Hello, first time posted, long time browser...
So, I have a bricked (or almost totally bricked) LG G2X. Here is what I did:
I had flashed the Hellfire Sandwich 1.9 rom and was just fine...until my phone started turning off randomly. After reading somewhere here that I should nullify my phone and the re-flash the rom in order to fix my issue.
So, I backed up my data and downloaded the Aroma Nullifier from Volk (thanks for all you do). I booted to recovery and ran the Nullifier. Once the Nullifier had stopped, still while in Recovery, I tried to access my sdcard to re-flash my Rom...well, I couldn't access my SD card. Furthermore, I couldn't unmount the SD or mount the USB Storage.
Here comes the big mistake:
So, as I was doing some research about how to proceed, my USB cord wiggled out of the phone and my phone lost power. Now, since I had read from Volk not to let that happen, I knew I was in trouble.
At this point, I can only load into the LG Boot Screen and my computer loads drivers for "Asus Android Device" (I have the Asus Transformer Prime Tablet) and under that title "Asus Android Bootloader Interface". No APX, No USB Controller....no other communication.
Last little note, I took the phone to the Tmobile store on a hunch one of the guys who works there had some experience (which he did), and while he was trying to boot into recovery from battery power (something I have been unable to do) he got the USB communication interface...something like "S/W Do not disconnect".... Since then, I have not been able to reproduce that interface.
I am at the end of my abilities...I haven't seen anything that addresses this particular problem though I have tried a bunch of solutions without success. I have looked all through XDA forums, but if there is one I missed, please let me know.
Any thoughts would be very helpful.
Kickingcans
If you haven't already, I recommend looking into nvflash. I'm almost certain you'll be able to fix this. nvflash works at a very low level, requiring that you connect your phone without a battery using a special startup sequence. You will need the APX driver (for Windows) to make it recognize your phone in this recovery mode. At that point, you should be able to flash CWM using nvflash and go from there. If you can't get into recovery, I seem to recall flashing the stock ROM itself with nvflash.
This thread should help you: forum.gsmhosting.com/vbb/archive/t-1503546.html (I can't link yet)
Specifically, the link in the "I solved it" post.
Good luck, and let us know when you get it working :good:
Thanks much...but...
therealnexion said:
If you haven't already, I recommend looking into nvflash. I'm almost certain you'll be able to fix this. nvflash works at a very low level, requiring that you connect your phone without a battery using a special startup sequence. You will need the APX driver (for Windows) to make it recognize your phone in this recovery mode. At that point, you should be able to flash CWM using nvflash and go from there. If you can't get into recovery, I seem to recall flashing the stock ROM itself with nvflash.
This thread should help you: forum.gsmhosting.com/vbb/archive/t-1503546.html (I can't link yet)
Specifically, the link in the "I solved it" post.
Good luck, and let us know when you get it working :good:
Click to expand...
Click to collapse
Thanks for the thoughts. I will try that all again, but I have tried nvflash and tried updating APX drivers. My computer only recognizes the phone as an "Android Bootloader Interface". When I try to manually update/change the drivers for the "Android Device", there is a problem with 64-Bit operating System (Windows 7 Home Premium). I was going to try to boot the computer in Safe Mode, but I don't know if that will help.
I haven't been able to communicate with the phone, and only saw the S/W Upgrade screen once and that was in the Tmobile store without access to my computer.
I am going to try those suggested steps again. Thanks again.
Leigh
Got it going....
THANKS SO MUCH. I knew I was missing something stupid. I kept reading the nvflash instructions and pressing the Power and Volume Down button instead of Volume Up and Down.
Things are going again. Thanks so much.
Kickingcans
Hi all, I have an Android tablet (Diablotek D2-721, very cheap I know, but it serves its purpose) that is stuck in a boot loop. The real problem here is that this device apparently does not have any sort of recovery mode and being in a boot loop means it does not get recognized by ADB or any firmware flashing software.
I researched all day yesterday perusing forum after forum but almost every single solution requires booting into recovery. Is anyone able to shed any light and tell me what my options might be at this point?
Thanks in advance.
S1lent Echoes said:
Hi all, I have an Android tablet (Diablotek D2-721, very cheap I know, but it serves its purpose) that is stuck in a boot loop. The real problem here is that this device apparently does not have any sort of recovery mode and being in a boot loop means it does not get recognized by ADB or any firmware flashing software.
I researched all day yesterday perusing forum after forum but almost every single solution requires booting into recovery. Is anyone able to shed any light and tell me what my options might be at this point?
Thanks in advance.
Click to expand...
Click to collapse
Maybe you can try to flash a recovery like CWM via ODIN.
Just my 2 cents!!
No, I cannot flash anything because the tablet refuses to talk to my computer while in this boot loop. I tried ADB, Odin, and the manufacturer's flashing tool but nothing would register the device as being connected. Plus I set up a second operating system and tried doing all of the same things on Windows 7 because Windows 8 has been problematic with drivers but it still made no difference. Still, thanks for the suggestion. x.O
The matter is null now. I just took it back and got another tablet, one with a recovery mode.
For anyone searching on this D2-721 tablet, be wary because with no recovery mode available it is very hard if nigh impossible to recover from a lot of things normally recoverable from any Android device. I tried for two days and spent hours pouring through forums but in the end my computer just could not talk to the tablet while in a boot loop. And trust me, I tried everything.
Thanks for the responses and help, it was appreciated.
I bricked a TF300T today, and I'd like to know if there is possibility that it might be repaired.
I was attempting to install CyanogenMod 10.1 on the tablet for my friends, which I offered to do since I have a bit of experience doing similar on other devices. It was running Android 4.2, and had the latest firmware (v10.6.1.15.3, WW). After researching the XDA forums, I unlocked and rooted the device, and installed the TWRP recovery (2.5.0.0). I used TWRP to flash CM 10.1 and the Google apps, but when I tried to boot I got stuck at the Asus logo. After some more research I realized that the official release of CM doesn't work with the 4.2 bootloader, and that if I wanted to install that ROM I would need to downgrade my bootloader (right?).
The trouble occurred during the downgrade. I downloaded the 10.4.2.20 firmware and used flashboot to flash it. The flash completely successfully and I was going to run "flashboot reboot." Thinking I'd save keystrokes on the command line, I hit the up arrow to call up my last command, and meant to delete the last half of it, but I managed to hit 'enter' instead, starting the flash over again. I cancelled the command (^C), which might not have been wise -- but then I made my dumbest move, and powered the device off. (I'm not really sure why; I guess I assumed I'd still be able to get into fastboot mode.)
Now the device will not boot at all, except into APX mode -- i.e., the screen is blank, but when plugged into the computer the device registers. From what I've read here, there isn't really anything useful I can do in APX mode, given that I never setup nvflash, and I can't figure out any way of getting the tablet to do anything else.
Is there anything I've missed? Is there anything I could accomplish by cracking open the tablet (popping out the battery)? I've seen references to replacing the logic board – would that work, and how should I go about this? I know most if not all of these questions have been answered in different places before, and I tried to do my homework, but I figured I'd ask in case anyone had new experience or expertise to share.
I think to only solution is to replace the main board OR buy a new tablet :'(
Sent from my ASUS Transformer Pad TF300T
jay-roc said:
I bricked a TF300T today, and I'd like to know if there is possibility that it might be repaired.
I was attempting to install CyanogenMod 10.1 on the tablet for my friends, which I offered to do since I have a bit of experience doing similar on other devices. It was running Android 4.2, and had the latest firmware (v10.6.1.15.3, WW). After researching the XDA forums, I unlocked and rooted the device, and installed the TWRP recovery (2.5.0.0). I used TWRP to flash CM 10.1 and the Google apps, but when I tried to boot I got stuck at the Asus logo. After some more research I realized that the official release of CM doesn't work with the 4.2 bootloader, and that if I wanted to install that ROM I would need to downgrade my bootloader (right?).
The trouble occurred during the downgrade. I downloaded the 10.4.2.20 firmware and used flashboot to flash it. The flash completely successfully and I was going to run "flashboot reboot." Thinking I'd save keystrokes on the command line, I hit the up arrow to call up my last command, and meant to delete the last half of it, but I managed to hit 'enter' instead, starting the flash over again. I cancelled the command (^C), which might not have been wise -- but then I made my dumbest move, and powered the device off. (I'm not really sure why; I guess I assumed I'd still be able to get into fastboot mode.)
Now the device will not boot at all, except into APX mode -- i.e., the screen is blank, but when plugged into the computer the device registers. From what I've read here, there isn't really anything useful I can do in APX mode, given that I never setup nvflash, and I can't figure out any way of getting the tablet to do anything else.
Is there anything I've missed? Is there anything I could accomplish by cracking open the tablet (popping out the battery)? I've seen references to replacing the logic board – would that work, and how should I go about this? I know most if not all of these questions have been answered in different places before, and I tried to do my homework, but I figured I'd ask in case anyone had new experience or expertise to share.
Click to expand...
Click to collapse
APX mode is useless without nvflash installed and nvflash can only be installed while on ICS and once you leave ICS you can't go back.
Some Info: the vehicles to recover without nvflash are
1. recovery - stock or twrp
2. adb
3. fastboot
Do any of these work?
Try this link to find ways you may not have used yet -to get to the bootloader - thus recovery or fastboot
[GUIDE] Enter APX mode or Bootloader-recovery menu!
For future reference here is the way I see the recovery and rom matching issue.
4.1 bootloader - 10.4.2.9, 10.4.2.13, 10.4.2.17, 10.4.2.18, 10.4.2.20 - twrp openrecovery-twrp-2.5.0.0-tf300t-JB.blob
4.2 bootloader - 10.6.1.8 - twrp openrecovery-twrp-2.4.4.0-tf300t-4.2.blob
4.2.1 bootloader - 10.6.1.15.3 - twrp openrecovery-twrp-2.5.0.0-tf300t-4.2.blob
tobdaryl said:
APX mode is useless without nvflash installed and nvflash can only be installed while on ICS and once you leave ICS you can't go back.
Some Info: the vehicles to recover without nvflash are
1. recovery - stock or twrp
2. adb
3. fastboot
Do any of these work?
Try this link to find ways you may not have used yet -to get to the bootloader - thus recovery or fastboot
[GUIDE] Enter APX mode or Bootloader-recovery menu!
Click to expand...
Click to collapse
Thanks for the response. I've already tried the relevant methods in the guide, except for disconnecting the battery. I can get into APX mode -- the tablet registers as an APX device when plugged into the computer -- but I can't get it to enter the bootloader, so recovery, adb, and fastboot do not work. At this point I don't have much hope that the device will ever boot again without replacing the motherboard.
jay-roc said:
Thanks for the response. I've already tried the relevant methods in the guide, except for disconnecting the battery. I can get into APX mode -- the tablet registers as an APX device when plugged into the computer -- but I can't get it to enter the bootloader, so recovery, adb, and fastboot do not work. At this point I don't have much hope that the device will ever boot again without replacing the motherboard.
Click to expand...
Click to collapse
I'm sorry, I hoped the guide would give you a chance of recovery.
I definitely appreciate the help, and the guide's a great resource.
tobdaryl said:
I'm sorry, I hoped the guide would give you a chance of recovery.
Click to expand...
Click to collapse
jay-roc said:
I definitely appreciate the help, and the guide's a great resource.
Click to expand...
Click to collapse
You are welcome!
I had wished for better results.
Good Luck!
noahvt said:
I think to only solution is to replace the main board OR buy a new tablet :'(
Click to expand...
Click to collapse
Is there any tips for buying mainboard? Should it be exactly the same as in my tablet (I mean the same region and, therefore, version of ROM installed), maybe serials.
I have a bricked TF300T, and the only way I have to resurrect it - MB replacement. So, please, ANY info will be useful. Thanks in advance.
try to get it into fastboot somehow - i was stuck in apx too but with a bit of trying i was able to get to fastboot (try resetbutton + vol-down, let it completly drain of power, charge it back and try again)
here is what i did after i regained fastboot:
http://forum.xda-developers.com/showpost.php?p=44244313&postcount=12
gl
-Buster
Buster99 said:
try to get it into fastboot somehow - i was stuck in apx too but with a bit of trying i was able to get to fastboot (try resetbutton + vol-down, let it completly drain of power, charge it back and try again)
here is what i did after i regained fastboot:
http://forum.xda-developers.com/showpost.php?p=44244313&postcount=12
gl
-Buster
Click to expand...
Click to collapse
I'm so damn appreciated! Thank you so much)) I'd add this way to get to fastboot - adb reboot fastboot - just from faulty CWM. Other way it didn't worked.
I got mine working this way
Link to my thread --> http://forum.xda-developers.com/showthread.php?p=45120193#post45120193
Hope it helps. Try It!
ozkrtech said:
Link to my thread --> http://forum.xda-developers.com/showthread.php?p=45120193#post45120193
Hope it helps. Try It!
Click to expand...
Click to collapse
I have the same problem...
My TF300T got bricked and now i cant boot at all anymore, i just see the Asus logo.
Vol down and power doesnt work but i think i can boot it into APX mode, screen stays black but my pc recognises an APX device.
At first my pc didnt install the driver but than i found APX drivers in these forums.
I've downloaded the APX drivers from a thread and i can choose to install various drivers, i tried all of them.
The one i think i need is the Asus Transformer ADB interface driver but this one along with every other one i can choose from doesn't work.
After installing and trying fastboot devices and adb devices i never had a device name show up
im kinda stuck right now
Can anyone please give me some advice ?
Cheers, any help is appreciated
marty
martyzzz said:
I have the same problem...
My TF300T got bricked and now i cant boot at all anymore, i just see the Asus logo.
Vol down and power doesnt work but i think i can boot it into APX mode, screen stays black but my pc recognises an APX device.
At first my pc didnt install the driver but than i found APX drivers in these forums.
I've downloaded the APX drivers from a thread and i can choose to install various drivers, i tried all of them.
The one i think i need is the Asus Transformer ADB interface driver but this one along with every other one i can choose from doesn't work.
After installing and trying fastboot devices and adb devices i never had a device name show up
im kinda stuck right now
Can anyone please give me some advice ?
Cheers, any help is appreciated
marty
Click to expand...
Click to collapse
Can you explain me step by step what you did to get bricked? Are you on bootloader 4.1 or 4.2+? 10.4.x.x is 4.1 and 10.6.x.x is 4.2+
ozkrtech said:
Can you explain me step by step what you did to get bricked? Are you on bootloader 4.1 or 4.2+? 10.4.x.x is 4.1 and 10.6.x.x is 4.2+
Click to expand...
Click to collapse
Bought the Asus tab a year back and kept it original and updated by Asus for a few months.
Begin this year i unlocked it through a guide here on XDA (i dont thin through the Asus APK but another way).
After it succesfully unlucked (you could see "your device is unlocked" in the left top of the Asus boot screen i installed CWM.
After CWM i installed Cyogenmod 10.1 and kept it updated for months
This was all in the beginning of this year...
In june after updating Cyogenmod 10.1 to a newer version it wouldnt boot up anymore (i still had acces to my CWM recovery at this time).
So i switched back to the last working Cyogenmod 10.1 version (think it was 15th or 16th june).
I left it again for 2 months, still everything was fine till i saw that Cyogenmod 10.2 was out on XDA.
The upcomming is all last week;
First i tried to install 10.2 through CWM but my tab wouldnt boot up.
Than i switched recovery through fastboot because i have read that 10.2 was only compatible with TWRP 2.5+ so i got the latest TWRP
(2.6.0.0 i think)
After booting into TWRP i fully wiped the tab (i might have wiped everything because i dont know TWRP so well), after the wipe i wanted to install 10.2 again.
My tab still didnt boot so i got anctious and wanted to switch back to my latest version 10.1 (june 2013 that did work) so i could at least use my tab again.
Installing 10.1 again didnt work through TWRP, after that i came to the conclusion that i couldt install any rom anymore, at every rom i got an error in TWRP so i thought i had the wrong TWRP installed. (see my other post for a link to the screenshot of the error msge, i just cant find it atm).
Last but not least i tried to load my old CWM again as recovery, after i did this i couldnt get into recovery anymore...
Thans basicly the whole story.
Hope some1 can help me out.
Thanks in advance !
Cheers
martyzzz said:
Bought the Asus tab a year back and kept it original and updated by Asus for a few months.
Begin this year i unlocked it through a guide here on XDA (i dont thin through the Asus APK but another way).
After it succesfully unlucked (you could see "your device is unlocked" in the left top of the Asus boot screen i installed CWM.
After CWM i installed Cyogenmod 10.1 and kept it updated for months
This was all in the beginning of this year...
In june after updating Cyogenmod 10.1 to a newer version it wouldnt boot up anymore (i still had acces to my CWM recovery at this time).
So i switched back to the last working Cyogenmod 10.1 version (think it was 15th or 16th june).
I left it again for 2 months, still everything was fine till i saw that Cyogenmod 10.2 was out on XDA.
The upcomming is all last week;
First i tried to install 10.2 through CWM but my tab wouldnt boot up.
Than i switched recovery through fastboot because i have read that 10.2 was only compatible with TWRP 2.5+ so i got the latest TWRP
(2.6.0.0 i think)
After booting into TWRP i fully wiped the tab (i might have wiped everything because i dont know TWRP so well), after the wipe i wanted to install 10.2 again.
My tab still didnt boot so i got anctious and wanted to switch back to my latest version 10.1 (june 2013 that did work) so i could at least use my tab again.
Installing 10.1 again didnt work through TWRP, after that i came to the conclusion that i couldt install any rom anymore, at every rom i got an error in TWRP so i thought i had the wrong TWRP installed. (see my other post for a link to the screenshot of the error msge, i just cant find it atm).
Last but not least i tried to load my old CWM again as recovery, after i did this i couldnt get into recovery anymore...
Thans basicly the whole story.
Hope some1 can help me out.
Thanks in advance !
Cheers
Click to expand...
Click to collapse
What happends when you press volume down+ power?
It jeeps rebooting or it goes to black screen? Have you tried pressing the reset button is below the micro sdcard slot.
You should be able to boot any recovery.
is I recall correctly cm switched partition layout to 4.2 on tf300.
if you still have fastboot try my guide to flash stock and then flash recovery and cm10.2. since it sounds a lot like my error I had with cm it should work for you as well.
good luck
Sent from my TF300T using xda app-developers app
ozkrtech said:
What happends when you press volume down+ power?
It jeeps rebooting or it goes to black screen? Have you tried pressing the reset button is below the micro sdcard slot.
You should be able to boot any recovery.
Click to expand...
Click to collapse
When i press vol down+power i get the asus boot screen for a minute or 2, the tab switches off and on again to the same boot screen.
I cant boot into recovery
---------- Post added at 06:51 PM ---------- Previous post was at 06:42 PM ----------
Buster99 said:
is I recall correctly cm switched partition layout to 4.2 on tf300.
if you still have fastboot try my guide to flash stock and then flash recovery and cm10.2. since it sounds a lot like my error I had with cm it should work for you as well.
good luck
Sent from my TF300T using xda app-developers app
Click to expand...
Click to collapse
I dont have fastboot in any way.
I can only power on the device with volume up + power to enter APX mode, than only my pc sees a USB device.
I tried a lot of differtent drivers but for nome of them i can ADB of Fastboot to the device.
It would help if someone that has managed to unbrick through APX mode posted the right driver for a TF300T
Cheers
have you tried the apx drivers that come with the sdk?
Sent from my GT-I9505 using xda app-developers app
Buster99 said:
have you tried the apx drivers that come with the sdk?
Sent from my GT-I9505 using xda app-developers app
Click to expand...
Click to collapse
Ive tried searching in the SDK forders but i cant find any.
If i try to install drivers automaticly and than point to the root SDK folder i get the windows msge the best drivers are already installed (no matter what driver is in stalled at that time)
martyzzz said:
Ive tried searching in the SDK forders but i cant find any.
If i try to install drivers automaticly and than point to the root SDK folder i get the windows msge the best drivers are already installed (no matter what driver is in stalled at that time)
Click to expand...
Click to collapse
don't just point at the folder
manually select the driver for the device from android-sdk\extras\google\usb_driver
gl
I am trying to resurrect my tf101. This is my starting point. Some time ago I installed cm10-20130929-NIGHTLY-tf101 into my tf101 using twrp. That installed fine but in the process something happened and I cannot boot into twrp I can now only boot into CM by holding the power button and volume up. I was not able to install gapps . Also I think my bootloader is corrupted because if I try to boot into it I just get a blank screen. I was able to install the Official TWRP App and can run it but it crashes every time "Unfortunately the app has stopped".
I am about ready to throw this laptop out because I have tried many options on this board and nothing worked. I can connect the tf101 to my computer and I can see it in device manager and I can open the laptop in file manager. I would even be willing to wipe the entire laptop and start from scratch but I don't know enough how to do this.
Any help or suggestions would be welcome.
Hi. First, I'll explain to you that for 10 years I had no contact with flashing phones. I didn't have any problems with the previous models. So I stopped somewhere at the level of the Samsung Galaxy S3-S4. Some time ago I decided that I would bring two Asus tf101s back to life and install a new KitKiss ROM on them. I set to work confidently. Turns out it's not that simple. I can do nothing. Some of the links have expired and the tips seem outdated. I can not upload a new recovery or even root the device. Strange things are happening. First of all, after turning on the device in recovery mode, after some time it goes into system boot and exits recovery. I've tried many ways and I don't understand any of it anymore. In the command line (CMD) it seems to see the device but does not want to respond to any commands, even to "adb reboot fastboot". I can do like this :
1. Ask for simple instructions for a "boy" and current links to the necessary files.
2. Look for someone who will perform a miracle and install the required Android for me.
Will someone help me?