Related
I have an interesting problem:
I have a tf300t curently running JRO03C.ww_epad-10.4.2.17-20121018
I ended up here after an unsuccessful flash with twrp. Tried to recover my back up with no joy. At this time it would only boot twrp recovery, finally flashed stock via micro sdcard and got it to boot again! Only I had no root anymore, so I tried to boot into recovery and there was none. So next I tried to boot into bootloader and when I select fastboot, the tablet says starting "starting fastboot download protocol" but after nothing else happens. ADB looses it, and it just stops right there.
The good news is that I can still use the tablet, it boots and everything works fine but I have no root. I have searched and read and searched and read. I don't know if the reflash flashes the bootloader but that didn't seam to have any effect. If anybody could point me in the right direction I would sure appriciate the help.
there is a way on the TWRP instructions using terminal when you are in system
nitsuj79 said:
I have an interesting problem:
I have a tf300t curently running JRO03C.ww_epad-10.4.2.17-20121018
I ended up here after an unsuccessful flash with twrp. Tried to recover my back up with no joy. At this time it would only boot twrp recovery, finally flashed stock via micro sdcard and got it to boot again! Only I had no root anymore, so I tried to boot into recovery and there was none. So next I tried to boot into bootloader and when I select fastboot, the tablet says starting "starting fastboot download protocol" but after nothing else happens. ADB looses it, and it just stops right there.
The good news is that I can still use the tablet, it boots and everything works fine but I have no root. I have searched and read and searched and read. I don't know if the reflash flashes the bootloader but that didn't seam to have any effect. If anybody could point me in the right direction I would sure appriciate the help.
Click to expand...
Click to collapse
I saw on another site that with this tablet it will go into fastboot but wont popup as fastboot device on your computer, but you can still use fastboot commands. worked for me
mikaole said:
there is a way on the TWRP instructions using terminal when you are in system
Click to expand...
Click to collapse
You must have root permission for that method
imp3r10 said:
I saw on another site that with this tablet it will go into fastboot but wont popup as fastboot device on your computer, but you can still use fastboot commands. worked for me
Click to expand...
Click to collapse
No when I try to flash recovery it says waiting for device and nothing ever happens.
I seamed to have got it. I down graded to 10.4.2.9 and back to 13. plugged it to the computer and this time it installed drivers and that time I was able to flash recovery. I don't know what happened and it was probably something that I was doing wrong. But just incase that is what did the trick and it helps someone else, i wanted to be sure and follow up.
I tried to install the android revolution hd one 71.1 on my phone and it went out good so far into the installation but after the installation, i rebooted my phone and it went to a boot logo then went to the TWRP recovery mode. i tried deleting the cache and doing a reset but nothing is happening. please help me.
patrickgrantm said:
I tried to install the android revolution hd one 71.1 on my phone and it went out good so far into the installation but after the installation, i rebooted my phone and it went to a boot logo then went to the TWRP recovery mode. i tried deleting the cache and doing a reset but nothing is happening. please help me.
Click to expand...
Click to collapse
Having the same problem. The phone only reboots into twrp recovery mode, yet shows no errors when re-flashing device with most recent version of sense ui.
I'd really like to be able to use my phone.
lurkeratthegate said:
Having the same problem. The phone only reboots into twrp recovery mode, yet shows no errors when re-flashing device with most recent version of sense ui.
I'd really like to be able to use my phone.
Click to expand...
Click to collapse
Flash latest stock RUU. Once phone is fixed you can go for a custom rom again
LS.xD said:
Flash latest stock RUU. Once phone is fixed you can go for a custom rom again
Click to expand...
Click to collapse
I tried that. My computer is no longer recognizing the device at all. I thought I was making progress through the first part of the day, but for some reason, usb recognition seems to fluctuate.
I'm normally pretty alright working with this type of thing, but this phone has me completely baffled.
lurkeratthegate said:
I tried that. My computer is no longer recognizing the device at all. I thought I was making progress through the first part of the day, but for some reason, usb recognition seems to fluctuate.
I'm normally pretty alright working with this type of thing, but this phone has me completely baffled.
Click to expand...
Click to collapse
Really weird. So you have no chance to get into fastboot mode, not even by selection reboot to bootloader in twrp?!
LS.xD said:
Really weird. So you have no chance to get into fastboot mode, not even by selection reboot to bootloader in twrp?!
Click to expand...
Click to collapse
I supposed I should have been more clear. Fastboot will work, but all of the adb commands fail as the "device not found". I have tried restarting everything multiple times, updated all of the drivers, deleted the drivers, re-installed them, and while it makes the chime noise when I plug the phone in, all I can do is look at it in device manager. I'm running windows 8.1 and twrp 2.8.5.0, by the way.
lurkeratthegate said:
I supposed I should have been more clear. Fastboot will work, but all of the adb commands fail as the "device not found". I have tried restarting everything multiple times, updated all of the drivers, deleted the drivers, re-installed them, and while it makes the chime noise when I plug the phone in, all I can do is look at it in device manager. I'm running windows 8.1 and twrp 2.8.5.0, by the way.
Click to expand...
Click to collapse
RUU flashing is fastboot based I suppose. So you won't need adb at all.
LS.xD said:
RUU flashing is fastboot based I suppose. So you won't need adb at all.
Click to expand...
Click to collapse
Wait, what? I can flash images like twrp to my phone via fastboot, but the only ruu's I've found either have executable wizard files, or are self extracting. How can I flash a rom or update utility using fastboot?
lurkeratthegate said:
Wait, what? I can flash images like twrp to my phone via fastboot, but the only ruu's I've found either have executable wizard files, or are self extracting. How can I flash a rom or update utility using fastboot?
Click to expand...
Click to collapse
Connect phone in fastboot mode, run RUU, click next plenty of times, and done
If your phone is S-ON, flash stock recovery first and relock the bootloader before running the RUU
Hi all,
I installed the TWRP recovery for my mate 7 - 09 version, with lollipop 5.1. But then I unknowingly wiped something I shouldn't have: I think it was the system folder. No backups were made
My phone keeps starting up to the huawei logo and then reboots\turns off. I can get into fastboot&rescue mode, but that's it. No recovery, no 3-button fix (as far as I know).
The second problem is that I cannot get my device to be recognised by my pc. adb devices doesn't give me any results.
I don't feel like I can install the drivers properly as well. Pherhaps thats the problem? How can I do this? I have a driversetup from a mate7 download, but double clicking it doesnt show any prompts.
Anyone who can help me in any way is more than welcome!
dekraan said:
Hi all,
I installed the TWRP recovery for my mate 7 - 09 version, with lollipop 5.1. But then I unknowingly wiped something I shouldn't have: I think it was the system folder. No backups were made
My phone keeps starting up to the huawei logo and then reboots\turns off. I can get into fastboot&rescue mode, but that's it. No recovery, no 3-button fix (as far as I know).
The second problem is that I cannot get my device to be recognised by my pc. adb devices doesn't give me any results.
I don't feel like I can install the drivers properly as well. Pherhaps thats the problem? How can I do this? I have a driversetup from a mate7 download, but double clicking it doesnt show any prompts.
Anyone who can help me in any way is more than welcome!
Click to expand...
Click to collapse
Hey Buddy, here's what you can try to do:
1.) Boot connect your phone to your computer.
2.) Next, boot your phone to fastboot.
3.) Next, open command prompt from the folder where your ADB files are stored.
4.)On CMD type:
fastboot devices
5.) If your device appears then you have 2 options now. You can either:
a.) Flash Stock recovery.img or
b.) Flash back TWRP
6.) If choosing option a.) you can then save stock firmware within dload folder on your external sd card then force upgrade via 3 btn method.
7.) If choosing option b.) you can boot to twrp then either sideload a custom rom or try to save on your external sd and flash
blitzkriegger said:
Hey Buddy, here's what you can try to do:
1.) Boot connect your phone to your computer.
2.) Next, boot your phone to fastboot.
3.) Next, open command prompt from the folder where your ADB files are stored.
4.)On CMD type:
fastboot devices
5.) If your device appears then you have 2 options now. You can either:
a.) Flash Stock recovery.img or
b.) Flash back TWRP
6.) If choosing option a.) you can then save stock firmware within dload folder on your external sd card then force upgrade via 3 btn method.
7.) If choosing option b.) you can boot to twrp then either sideload a custom rom or try to save on your external sd and flash
Click to expand...
Click to collapse
I'll give that a try, thank you. With step 1, you just mean: connect the phone through usb to the computer, right?
When I rooted the phone, I did so on my work laptop, so I am hoping I can get it recognised there, but lets see what happens at home.
EDIT:
Ok, i've typed in fastboot devices, and it gave me one line with a 16-digit code (numbers and letters) some white space and then the word fastboot. What does that mean?
That should meen it recognizes your phone in fastboot mode. Next step is to flash as stated in step 5 that in the instructions.
Sent from my HUAWEI MT7-L09 using Tapatalk
dekraan said:
I'll give that a try, thank you. With step 1, you just mean: connect the phone through usb to the computer, right?
When I rooted the phone, I did so on my work laptop, so I am hoping I can get it recognised there, but lets see what happens at home.
EDIT:
Ok, i've typed in fastboot devices, and it gave me one line with a 16-digit code (numbers and letters) some white space and then the word fastboot. What does that mean?
Click to expand...
Click to collapse
EDIT AGAIN:
Ok, this is what I did. I downloaded the well known mate7 package, extracted the b119 tools folder and I put the twrp_2.8.7.0_mate7_5.1.img file from this forum (the TWRP for 5.1) inside this folder.
Then, I open cmd inside the folder, and I typed: fastboot flash recovery twrp_2.8.7.0_mate7_5.1.img. This is what happens:
target reported max download size of 471859200 bytes
sending 'recovery'(12644 KB)...
OKAY [ 1.302s]
writing 'recovery'...
OKAY [ 0.455s]
finished. total time: 1.756s
Now, I finally managed to get back into TWRP! I've only got 2% battery though (but I see a + which I think means charging...EDIT: yes, it is on 3% now. Better leave it like this...).
It tells me this:
TWRP has detected an unmodified system partition.
TWRP can leave your system partition unmodified to make it easier for you to take official updates. TWRP will be unable to prevent the stock rom from replacing TWRP and will not offer to root your device. Installing zips or performing adb operations may still modify the system partition.
I decided to swipe, to allow modifications.
So, I've got twrp back! For lollipop. This probably means I have to flash the lollipop rom? I will download the update.zip file next and put it on my sd card (using my pc and a microsd adapter...)
Keep you posted!
Ok, this is not working.
I put update.zip on my sd-card, and tried to install it. This is what I get:
Installing 'sd-ext/update.zip'...
checking for MD5 file...
Skipping MD5 check: no MD5 file found
E:unknown command [errno]
file_getprop: failed to stat
E: error executing updater binary in zup 'sd-ext/update.zip'
Error flashing zip 'sd-ext/update.zip'...
Updating partition details...
...done
EDIT:
I tried to sideload but on my pc I get:
error: protocol fault (no status)
And on my TWRP I get:
You need adb 1.0.32 or newer to sideload to this device.
EDIT:
Updated my adb to 1.0.32 for windows, and rebooted everything. Now i'm at 6% of sideload. Hoping this will work!
EDITn the PC everything seems to go ok, but on my phone it says: E:Zip signature verification failed:1
What should I try next?
dekraan said:
Ok, this is not working.
I put update.zip on my sd-card, and tried to install it. This is what I get:
Installing 'sd-ext/update.zip'...
checking for MD5 file...
Skipping MD5 check: no MD5 file found
E:unknown command [errno]
file_getprop: failed to stat
E: error executing updater binary in zup 'sd-ext/update.zip'
Error flashing zip 'sd-ext/update.zip'...
Updating partition details...
...done
EDIT:
I tried to sideload but on my pc I get:
error: protocol fault (no status)
And on my TWRP I get:
You need adb 1.0.32 or newer to sideload to this device.
EDIT:
Updated my adb to 1.0.32 for windows, and rebooted everything. Now i'm at 6% of sideload. Hoping this will work!
EDITn the PC everything seems to go ok, but on my phone it says: E:Zip signature verification failed:1
What should I try next?
Click to expand...
Click to collapse
I don't advise you to flash lollipop firmware first. It's more prudent to go back to kitkat first as I believe Lollipop needs kitkat as base
1.) Put stock kitkat update.app on dload folder of your memory card. Also make sure you have the LO9 stock kitkat recovery.
2.) With your phone connected to pc, go to twrp and reboot to bootloader.
3.) Once on bootloader open cmd on your tools folder then fastboot flash the stock kitkat recovery.
4.) Once done, fastboot reboot then force upgrade to install stock firmware.
5.) Once you have stock kitkat follow the drill to reach lollipop
blitzkriegger said:
I don't advise you to flash lollipop firmware first. It's more prudent to go back to kitkat first as I believe Lollipop needs kitkat as base
1.) Put stock kitkat update.app on dload folder of your memory card. Also make sure you have the LO9 stock kitkat recovery.
2.) With your phone connected to pc, go to twrp and reboot to bootloader.
3.) Once on bootloader open cmd on your tools folder then fastboot flash the stock kitkat recovery.
4.) Once done, fastboot reboot then force upgrade to install stock firmware.
5.) Once you have stock kitkat follow the drill to reach lollipop
Click to expand...
Click to collapse
Hi, thank you for your advice. I have but one question remaining: what stock kitkat update should I use? And where can I find the right recovery that goes with it?
I've tried several recovery_stock.img I found, and it does take away TWRP, so it might have done the trick. Only problem is that I cannot force upgrade to install whats on my sd-card....The phone keeps turning on (after a long push) and after seeing the logo for a little while, it turns off (short vibration)... Is there another way?
dekraan said:
Hi, thank you for your advice. I have but one question remaining: what stock kitkat update should I use? And where can I find the right recovery that goes with it?
I've tried several recovery_stock.img I found, and it does take away TWRP, so it might have done the trick. Only problem is that I cannot force upgrade to install whats on my sd-card....The phone keeps turning on (after a long push) and after seeing the logo for a little while, it turns off (short vibration)... Is there another way?
Click to expand...
Click to collapse
You should flash B137SP03 firmware. You can also refer to this guide:
http://forum.xda-developers.com/mate-7/help/5-1-to-4-4-2-bootloop-t3132888
1.)Prepare the Stock B137SP03 firmware on your SD card
2.)Download the fastboot.zip guide and extract it to a separate folder.
3.) next connect your phone to your computer and go to fastboot mode.
4.) Flash the boot.img and recovery.img you find on that guide.
5.) Once done, do the force upgrade with the B137 firmware.
blitzkriegger said:
You should flash B137SP03 firmware. You can also refer to this guide:
http://forum.xda-developers.com/mate-7/help/5-1-to-4-4-2-bootloop-t3132888
1.)Prepare the Stock B137SP03 firmware on your SD card
2.)Download the fastboot.zip guide and extract it to a separate folder.
3.) next connect your phone to your computer and go to fastboot mode.
4.) Flash the boot.img and recovery.img you find on that guide.
5.) Once done, do the force upgrade with the B137 firmware.
Click to expand...
Click to collapse
I've followed the guide you are reffering to. And I flashed the boot and recovery, and managed to get the roll back force installed. But for the life of me, I cannot get my phone to force install the B137 zip. I just can't get into force install mode. Are there tips or tricks? I am holding power up and down, and then press power untill I feel a short vibration. But all it does it show me the huawei logo screen and then shuts down again.
Very frustrating!
EDIT:
ok, I noticed that when my sd-card is not inserted, the phone easily boots into the force install mode. It shows the logo for a couple of seconds, screen goes black and then the force install loads. So this is what I did: insert the sd card half way, press vol up and down, and power on. Then after the logo when the screen goes black, insert the sd-card all the way and when the phone goes to force install mode, it can find the update!
Now installing.... hope this helps someone else out there!
Worked! And I am up and running again! Thank you for saving my mate
I got my Mate bricked and i've been trying to figure out how to solve it. I tried lots of things from different guides, but just an hour ago I found this guide and it worked! I can't tell you how happy I am right now, thanks guys!
aleksik said:
I got my Mate bricked and i've been trying to figure out how to solve it. I tried lots of things from different guides, but just an hour ago I found this guide and it worked! I can't tell you how happy I am right now, thanks guys!
Click to expand...
Click to collapse
Glad to hear both of you guys have your mates up and running again. As long as a phone turns on and is not dead as a brick there's always hope it can be restored
Hi everyone, I have the same problem with my mate 7, i was messing with unlocking bootloader(which I succesfully have done), couldn't get my phone rooted so installed TWRP recovery for Lollipop(which was already installed when i bought the phone). Ended up with soft bricked phone(no OS, no recovery at all).
I tried different tutorials how to fix it, none of them worked(including that one unfortunatelly).
I have taken some pictures to show you what the problem is but cannot post them until reach 10 posts on forum
Basically, i can get into fastboot mode by holding volume down with power button. Windows and Hisuite don't recognise my device but in fastboot mode i can check devices connected. Typing "fastboot devices" i get "P6Q7M14A15008421 fastboot", which i guess is my device indeed.
After that i try flashing boot.img and recovery.img(which are reported OK). Then rebooting with 3 button(vol up and down, power) and Huawei logo screen appears for a bit and goes into white screen saying "rescue mode" and at the bottom: "Error Func NO: 10(FUNC_BOOT_RECOVERY) Error NO:2". Trying rebooting into recovery mode(vol up and power) it shows similar "recovery mode" screen but with different errors: "Error! Func NO:12(FUNC_LOAD_IOM3) Error NO:1".
That's it! It seems like i cannot flash my device successfully for some reason. What Windows version did you guys use?? I tried Win 8.0 and Win 10, maybe i should use older systems? Please help, i had my phone for a week only and broke it(
I can't help you much because I don't have enough knowledge about these kind of things.. I use Windows 7 and from my previous experiences I can say that working with Windows 8 can be frustrating. PS. I bricked my Mate 12hrs after buying it
muzammil84 said:
Hi everyone, I have the same problem with my mate 7, i was messing with unlocking bootloader(which I succesfully have done), couldn't get my phone rooted so installed TWRP recovery for Lollipop(which was already installed when i bought the phone). Ended up with soft bricked phone(no OS, no recovery at all).
I tried different tutorials how to fix it, none of them worked(including that one unfortunatelly).
I have taken some pictures to show you what the problem is but cannot post them until reach 10 posts on forum
Basically, i can get into fastboot mode by holding volume down with power button. Windows and Hisuite don't recognise my device but in fastboot mode i can check devices connected. Typing "fastboot devices" i get "P6Q7M14A15008421 fastboot", which i guess is my device indeed.
After that i try flashing boot.img and recovery.img(which are reported OK). Then rebooting with 3 button(vol up and down, power) and Huawei logo screen appears for a bit and goes into white screen saying "rescue mode" and at the bottom: "Error Func NO: 10(FUNC_BOOT_RECOVERY) Error NO:2". Trying rebooting into recovery mode(vol up and power) it shows similar "recovery mode" screen but with different errors: "Error! Func NO:12(FUNC_LOAD_IOM3) Error NO:1".
That's it! It seems like i cannot flash my device successfully for some reason. What Windows version did you guys use?? I tried Win 8.0 and Win 10, maybe i should use older systems? Please help, i had my phone for a week only and broke it(
Click to expand...
Click to collapse
Sounds like the wrong boot.img or recovery.img has been flashed. May I know what Mate 7 model you have and which Lollipop firmwre version your phone came last with?
Try to obtain boot.img and revoery.img for your lollipop version then flash that via fastboot
blitzkriegger said:
Sounds like the wrong boot.img -recovery.img has been flashed. May I know what Mate 7 model you have and which Lollipop firmwre version your phone came last with?
Try to obtain boot.img and revoery.img for your lollipop version then flash that via fastboot
Click to expand...
Click to collapse
My phone mt7-09l, european version 16gb. Came with lollipop 5.1 when I bought it but I think I have formatted it via twrp recovery so it shouldn't matter what boot and recovery version I am trying to flash, should it? I'll extract boot and recovery from b308 today andtry that, see if this works. If not, only thing I can try is using win7 and that's it really, no more possibilities
dekraan said:
I've followed the guide you are reffering to. And I flashed the boot and recovery, and managed to get the roll back force installed. But for the life of me, I cannot get my phone to force install the B137 zip. I just can't get into force install mode. Are there tips or tricks? I am holding power up and down, and then press power untill I feel a short vibration. But all it does it show me the huawei logo screen and then shuts down again.
Very frustrating!
EDIT:
ok, I noticed that when my sd-card is not inserted, the phone easily boots into the force install mode. It shows the logo for a couple of seconds, screen goes black and then the force install loads. So this is what I did: insert the sd card half way, press vol up and down, and power on. Then after the logo when the screen goes black, insert the sd-card all the way and when the phone goes to force install mode, it can find the update!
Now installing.... hope this helps someone else out there!
Click to expand...
Click to collapse
I'm stuck on this stage, no errors while flashing but no boot either. Shows logo then like a spark a bit of music and animation (1 sec maybe) and reboot, so on and on and on...
muzammil84 said:
My phone mt7-09l, european version 16gb. Came with lollipop 5.1 when I bought it but I think I have formatted it via twrp recovery so it shouldn't matter what boot and recovery version I am trying to flash, should it? I'll extract boot and recovery from b308 today andtry that, see if this works. If not, only thing I can try is using win7 and that's it really, no more possibilities
Click to expand...
Click to collapse
If you were on Lollipop when everything went sour, you should do what I did, thanks to advice from @blitzkriegger:
You should flash B137SP03 firmware. You can also refer to this guide:
http://forum.xda-developers.com/mate...tloop-t3132888
1.)Prepare the Stock B137SP03 firmware on your SD card
2.)Download the fastboot.zip guide and extract it to a separate folder.
3.) next connect your phone to your computer and go to fastboot mode.
4.) Flash the boot.img and recovery.img you find on that guide.
5.) Once done, do the force upgrade with the B137 firmware.
I used the full steps from the link in there: flashed the right boot and recovery through fastboot. Then I flashed the rollback zip from my sd-card, and then I flashed the B137 zip from my sd-card. I can't tell you more about it, obviously
brack11 said:
I'm stuck on this stage, no errors while flashing but no boot either. Shows logo then like a spark a bit of music and animation (1 sec maybe) and reboot, so on and on and on...
Click to expand...
Click to collapse
Been there, done that. Very frustrating! I've tried several things, none of which are probably the right way, but they worked for me. sometimes....
Can you get into stock recovery (vol+ and power)? What I tried several times was wipe cache, and then hold the powerbutton untill my phone turned off. That worked occasionally to get the device totally turned off. Then try to get to force update with your sd-card half way in, and flip it in totally when the logo dissapears and the screen is black. I also tried to shut down the constant starting up by going into fastboot/recovery mode and then holding power down. As long as it takes. Good luck! And hopefully someone can give you proper advice...
Hello guys !
First of all, thank you to you all for all the help i've already found on the forum.
I've got an Honor 8, and I tried to flash it for solving battery drain.
After several attempts and almost get there, now the phone is totally bricked.
Here some useful information:
- Bootloader in unlocked
- When in fastboot mode, Fastboot recognize my device but not ADB. I tried installing several drivers but nothing
- Flashing different recovery from fastboot don't work. I mean, it works but the device don't enter in recovery mode ( stuck in Your device is booting now....)
When try to install an update.app from stock recovery, i get error, both unable to find the package and unable to verify the package content.
When first I wasable to get in TWRP, when trying flashing a rom, it alwayg gaves me error like UNABLE TO MOUNT /DATA or /CACHE.
I think I really messed up with partitions and now everything seems doesn't be able to get into the phone.
I started yesterday, still here....
I guess dozens of users encountered same problems, I've tried everythinh from the forum but nothing worked....
Someone has any idea ? Cause my girlfriend will soon kill me.....
Yeah, even with volume up and power. It stuck on boot.
I've tried the most common fix, tried several twrp and rom. Same for update from SD, tried everything, différents rom, rollback....
Nothing...
Rommco05 said:
What happens when you hold +/-/off,on together?
Click to expand...
Click to collapse
It starts in automatic update mode. When trying to connect to WI-FI and download, an error message appear, seems unable to found the update.
When trying to update from SD, several update.app has failed.
When trying to clean all data from Emui recovery mode, the first 2 attempt stops at 7%, the third stops at 99%. Every time i have tried...
I really think is a partition issues, something that don' let the firmware recognize the phone and get the update
Rommco05 said:
Whitch model you have and witch fw you had installed before problem?
Click to expand...
Click to collapse
I have a FRD-L09 and i had the last update B380
Yeah the rollback package revives any brick. I've been through it all once and this will fix any mess so find a way to flash it.
By the way to access recovery you need to have your phone not plugged to USB (that's the bit i was missing for a long time) With your phone completely off (you can turn it off from the eRecovery (vol+ vol- power) ) hold vol+ & power and when the phone vibrates let go off the power and just hold vol+
http://www.hihonor.com/uk/support/details/index.html?DOC_ID=92131 and then flash B131 fw
http://www.hihonor.com/uk/support/details/index.html?DOC_ID=92101
if you can't get into recovery use huawei firmware extractor and get a recovery.img from one of those firmware packages and flash it via fastboot mode.
sysak said:
Yeah the rollback package revives any brick. I've been through it all once and this will fix any mess so find a way to flash it.
By the way to access recovery you need to have your phone not plugged to USB (that's the bit i was missing for a long time) With your phone completely off (you can turn it off from the eRecovery (vol+ vol- power) ) hold vol+ & power and when the phone vibrates let go off the power and just hold vol+
http://www.hihonor.com/uk/support/details/index.html?DOC_ID=92131 and then flash B131 fw
http://www.hihonor.com/uk/support/details/index.html?DOC_ID=92101
if you can't get into recovery use huawei firmware extractor and get a recovery.img from one of those firmware packages and flash it via fastboot mode.
Click to expand...
Click to collapse
Ok, tries, an error message says "impossible to find the package".
Maybe there are some issues with the SD card formatting, so he's not able to get into the dload folder ?
Rommco05 said:
Can you try another sd card or format on pc?
Click to expand...
Click to collapse
In FAT32 ?
Tonioparis said:
Ok, tries, an error message says "impossible to find the package".
Maybe there are some issues with the SD card formatting, so he's not able to get into the dload folder ?
Click to expand...
Click to collapse
did you extract the rollback package?
and yes important to put extracted update.app into dload folder on SD and unplug your device while doing this
if not flash stock recovery, system and so one with huawei extractor from your current running rom
you can enter fastboot mode, turn off your device and hold volume down + power, try this with plugged or unplugged device, but must be turned off..if this helps enter fastbootmode, then flash the extracted images
Dimontiman said:
did you extract the rollback package?
and yes important to put extracted update.app into dload folder on SD and unplug your device while doing this
if not flash stock recovery, system and so one with huawei extractor from your current running rom
you can enter fastboot mode, turn off your device and hold volume down + power, try this with plugged or unplugged device, but must be turned off..if this helps enter fastbootmode, then flash the extracted images
Click to expand...
Click to collapse
Hey...Seems to be working....:cyclops::cyclops::cyclops:
Rommco05 said:
after format card?
Click to expand...
Click to collapse
YYYESSSSSSSSS !!!!
All this time I tried everything and it was the SD card....formatted in NTFS....
MANY THANKS GUYS !!
Now, meanwhile I needed a phone and I got a P10....
Anyone need an Honor 8???
eheh
Yeah, of coure ! Was a joke, means I should probably learn patience
Just another question : when power on now there's no "You can't trust your device".
May I assule that now the bootloader is blocked ?
Thanks again to you all guys !
Rommco05 said:
Yes now is bootloader relocked, you can try again experiments but be carefull and read before anything you do and dont know what you do
Click to expand...
Click to collapse
I guess i'll still like that eheh.
My only concern is about battery drain. I'll try to stay with marshmallow and see if is better than Nougat !
Rommco05 said:
Noo Nougat is match better! https://forum.xda-developers.com/showpost.php?p=72177403&postcount=133
Click to expand...
Click to collapse
uhm but I cannot get the B381 OTA, isn it ?
Rommco05 said:
Dont wait for OTA, use Firmware Finder or flash via twrp...
Click to expand...
Click to collapse
you mean maees around with the bootloader again eh ? ahah
Ok i downloaded the full OTA, but how to install it directly ?
Tonioparis said:
Ok i downloaded the full OTA, but how to install it directly ?
Click to expand...
Click to collapse
Update process:
1. Unzip [extract] the update.zip to the SD card into the dload folder (if folder is not present, create it yourself)
2. In the phone app, enter the combination *#*#2846579#*#*, then select "Software Upgrade" and
The update from SD start
3. Delete the data in the dload folder
4. Repeat point 1-3 with the update_data_full_hw_eu.zip
5. WipeCache (personal recommendation)
Hello
I bought a Huawei x2 and brought a Chinese rom that gave me many problems.
I tried to ask him for updates using the "dload" method but he gave me an error.
The fact is that I formatted it from Flashtool thinking that I had the bootloader open.
After trying everything, he discovered that the bootloader is closed, but now the phone does not boot because I think I have flashed the entire system.
Flash a recovery, it makes me ok but then it does not pass Huawei's logo.
I guess without opening the bootloader it will be impossible to fix it.
I can access the Fastboot mode but I do not know what to do.
I also tried to flash img from the Huawei Extractor, which had previously worked on another X2 that I had brickered.
I guess without the open bootloader it's impossible to do anything.
I need your help. Thank you
Checked in fastboot, bootloader is unlocked.
But I cant install Twrp
I erase system, boot, user data etc
And now I dont have fastboot mode
Running error
boot image security verify failed
Help, please
lobodemonte said:
I erase system, boot, user data etc
And now I dont have fastboot mode
Running error
boot image security verify failed
Help, please
Click to expand...
Click to collapse
Flash this boot.img in fastboot which should still work. This boot.img is from B212 but should work on any B2xx rom. I'm not sure how else to help you when I don't know much about your device.
https://drive.google.com/file/d/1Ss3nkPJhQrlfHRgQzBRqXxTw6N7Pmz91/view?usp=sharing
Thanks ,but now I dont have access to fastboot mode
You have to use a usb cable and connect your phone to your PC first.
Then press volume down first + power to boot into Fastboot.
I know how use fastboot but now phone cant enter in fastboot..
Boot from B212 dont work
lobodemonte said:
Boot from B212 dont work
Click to expand...
Click to collapse
I don't know how else to help you. If you want to ship me your device Ill get it working for you and ship it back. You should always be able to get into the bootloader to run fastboot commands.
Now I can enter in fastboot.
I tried ALL but dont works.