I have E6653 on Fido, and the LTE seems pretty bad from my house and is overall rather spotty ranging from 0-3 bars. Outside I can get 3-4 bars in some areas, but at home I can get next to no bars of LTE but still full bars of HSPA+/3G...
Same here on Rogers.. I believe it has something to do with the fact that the modem is Bell by default as its a Belll exclusive phone. so unless rogers ( which also owns fido ) carries it, I don't think we'll see a radio / modem we can flash to make it better... Mines absolutely terrible and I'm downtown toronto
Mine is a factory-unlocked import from Taiwan. I only had a prepaid 3G unlimited data plan in Taiwan so I was unable to test its LTE reception there.
The thing is, when there's 0 bars of LTE it should just switch to HSPA... I was on Telus before and their LTE was very good and only rarely switched to HSPA...
Related
2nd time my phone dropped to EDGE for like 1+ hours. Is this my phones fault or T-mobiles?
I've got the KB3 radio + CM7 Nightly 26
T-Mobile and orange share siginal, if its dropping to EDGE you could have bad siginal on T-Mobile 3g /Orange 3g /or HDSPA so its dumped you onto the next best connection in the area.
or your phones having a hissy fit like mine does and drops to really **** GPRS / EDGE in my house then when you go into a new Cell area, 3g gets a lock and then it works again in your usual area.
i had no 3g only G in my house where i usually get almost 2meg over 3G, so i drove to work and when i checke dit in that area ( 12 miles away ) 3G was back and then when i got home it was still connected to 3G
I'm in the US so there's really only AT&T and T-mobile competing the GSM bands. Verizon and Sprint got their own thing going on.
I just switched to VZW, and I'm somewhat confused: should I be able to get data over CDMA? EvDO is 3G, are my options 3G, 4G, or bust? GSM has GPRS, which will faithfully deliver me data nearly wherever I am.
I don't know whether my VZW phone is simply mis-configured, or whether EV-DO is required for data access.
evdo rev a is verizon and sprints 3g
Is there anything slower than evdo on Verizon?
FFS one of you has got to bleeding know.
in some rare areas there might be evdo rev 0 witch is a tad bit slower.
1x which is national acesss and will be slower than dial up...
i almost never saw a "1x" / 1xEV-DO / cdma2000 icon on my phone during this trip. when i very rarely did see some icon on screen, it was usually 3G.
would you expect this on a somewhat-off-the-path road trip? i often had 5 bars, but still no data service; that seemed extremely odd to me coming from AT&T.
cdma has a 1x, it's like a gprs in gms
thanks for the help all. seems clear enough now.
now if only 1X had the availability/saturation of gprs, which seemed available basically everywhere.
Hello,
I have been seeing horrible quality of network service in my area on Ting. I have a white 32GB Nexus 5. I work in a three story building that seems to turn my phone into Digital roaming/CDMA 1xRTT network only going outside I barely get 3G. I have mapped it out and see more service in the area where people on Sprint are getting 4G LTE in the area or WIMAX. I was wondering if anyone on Ting/Sprint has the same issue.
I do see 3G on my commute and downtown Sacramento, California where I should see 4G LTE I am barely getting 3G 2 to 3 bars. Most of my day at work in Folsom, California area is all 1xRTT 2G or Roaming when inside my office, and lower end 3G outside. I have two 3G/WIMAX towers next to my area at work in Folsom and I should be getting some 3G.
I went through the cell network code to enable band 26, and band 41 and changed priorities on the band from 1 to 0 and individually tested each band in my area. band 41 seems to be the best and the others are pretty bad. Band 41 gets me -100 dBm, 99asu, 950ms ping on CDMA 1xRTT.
I now have it back to all priority 1 (Bands: 25/26/41) Band 26 and 41 enabled. I have updated my Profile and PRL multiple times.
I am running 4.4.2 with Xposed Framework version 1.5, with Franco kernel r33. I did see Franco kernel r34 and will probably flash the update ASAP to see if it works any better. I am not using any power save settings for cell network quality. I am also using a Spiegen slim-armor case and tried to see if it was interfering with signal strength, it wasn't.
So my question comes down to has anybody known a fix for getting solid 3G in an area where I should be seeing some LTE and atleast full strength 3G. I am barely seeing 2G most of the time. I am just crossing my finger it isn't an antenna issue with the phone itself.
Any help, tips, or tricks would be greatly appreciated!!!
adramalech707 said:
Hello,
I have been seeing horrible quality of network service in my area on Ting. I have a white 32GB Nexus 5. I work in a three story building that seems to turn my phone into Digital roaming/CDMA 1xRTT network only going outside I barely get 3G. I have mapped it out and see more service in the area where people on Sprint are getting 4G LTE in the area or WIMAX. I was wondering if anyone on Ting/Sprint has the same issue.
I do see 3G on my commute and downtown Sacramento, California where I should see 4G LTE I am barely getting 3G 2 to 3 bars. Most of my day at work in Folsom, California area is all 1xRTT 2G or Roaming when inside my office, and lower end 3G outside. I have two 3G/WIMAX towers next to my area at work in Folsom and I should be getting some 3G.
I went through the cell network code to enable band 26, and band 41 and changed priorities on the band from 1 to 0 and individually tested each band in my area. band 41 seems to be the best and the others are pretty bad. Band 41 gets me -100 dBm, 99asu, 950ms ping on CDMA 1xRTT.
I now have it back to all priority 1 (Bands: 25/26/41) Band 26 and 41 enabled. I have updated my Profile and PRL multiple times.
I am running 4.4.2 with Xposed Framework version 1.5, with Franco kernel r33. I did see Franco kernel r34 and will probably flash the update ASAP to see if it works any better. I am not using any power save settings for cell network quality. I am also using a Spiegen slim-armor case and tried to see if it was interfering with signal strength, it wasn't.
So my question comes down to has anybody known a fix for getting solid 3G in an area where I should be seeing some LTE and atleast full strength 3G. I am barely seeing 2G most of the time. I am just crossing my finger it isn't an antenna issue with the phone itself.
Any help, tips, or tricks would be greatly appreciated!!!
Click to expand...
Click to collapse
Go to about phone and check your Baseband version, if your modem driver is older you may want to upgrade it. Or if it is newer, potentially a downgrade has shown better performance as well. All depends.
Read this thread thoroughly and make sure you do a backup before doing anything and see if this helps.
http://forum.xda-developers.com/showthread.php?t=2514095
adramalech707 said:
Hello,
I have been seeing horrible quality of network service in my area on Ting. I have a white 32GB Nexus 5. I work in a three story building that seems to turn my phone into Digital roaming/CDMA 1xRTT network only going outside I barely get 3G. I have mapped it out and see more service in the area where people on Sprint are getting 4G LTE in the area or WIMAX. I was wondering if anyone on Ting/Sprint has the same issue.
I do see 3G on my commute and downtown Sacramento, California where I should see 4G LTE I am barely getting 3G 2 to 3 bars. Most of my day at work in Folsom, California area is all 1xRTT 2G or Roaming when inside my office, and lower end 3G outside. I have two 3G/WIMAX towers next to my area at work in Folsom and I should be getting some 3G.
I went through the cell network code to enable band 26, and band 41 and changed priorities on the band from 1 to 0 and individually tested each band in my area. band 41 seems to be the best and the others are pretty bad. Band 41 gets me -100 dBm, 99asu, 950ms ping on CDMA 1xRTT.
I now have it back to all priority 1 (Bands: 25/26/41) Band 26 and 41 enabled. I have updated my Profile and PRL multiple times.
I am running 4.4.2 with Xposed Framework version 1.5, with Franco kernel r33. I did see Franco kernel r34 and will probably flash the update ASAP to see if it works any better. I am not using any power save settings for cell network quality. I am also using a Spiegen slim-armor case and tried to see if it was interfering with signal strength, it wasn't.
So my question comes down to has anybody known a fix for getting solid 3G in an area where I should be seeing some LTE and atleast full strength 3G. I am barely seeing 2G most of the time. I am just crossing my finger it isn't an antenna issue with the phone itself.
Any help, tips, or tricks would be greatly appreciated!!!
Click to expand...
Click to collapse
Look for the modem thread (didn't see you post it so if you did, sorry), and try flashing the .15 radio. That seems to be the best. The stock 4.4.2 radio (.21 or .23 can't remember) sucks. I could be halfway between towers and drop to 3g and not get LTE at all. The .15 holds LTE as long as there is really an LTE signal just fine.
i just read that ting uses sprints network. that might be the issue there, as sprint isnt known to have great coverage nor great data speeds.
adramalech707 said:
Hello,
!
Click to expand...
Click to collapse
Sacramento is entirely legacy lucent equipment. Basically **** sucks and won't get better anytime soon till they cluster launch the area. They won't fire up anything (3g / 800 mhz / 4G LTE) until they cluster launch. They can't cluster launch the area until all 200 or so sites are fully upgraded which is a ways off.
B41 is running of old Clearwire sites for now and should be mostly done by around may but you cannot connect to them unless you force LTE only mode and do the PRL update work around (i.e. PRL update every time you reboot the radio) and even then it leaves much to be desired.
So your option is to stick it out on the ****ty legacy network or find another provider that suits your needs. ATT is running 5 mhz on LTE 700 B, Tmobile has a 10x10 FDD-LTE network on AWS that is spotty as **** in around south sac area and drops to Edge when you go indoors which is probably a no go for you.
Probably the best option for you is an ATT MVNO considering your needs are inside a building.
-- Though if you do stick it out Sprint has quite an amazing portfolio in the Sacramento area with full access to eSMR 800 (5x5 mhz FDD-LTE band 26) + eSMR 800 1xAdvance, 20 mhz of PCS A-F + the 10mhz of PCS G (5x5mhz FDD-LTE Band 25) along with 55mhz of BRS (2500) + innumerable EBS (2600). Right now they're running B41 on EARFCN 40978 which is about 2630mhz or smack dab in the EBS block.
Tmobiles is here at 40mhz of AWS and ~30 mhz of PCS + the 700A later this year. They run 10x10 for FDD-LTE Band 4 and DC-HSPA+ on the other 20 mhz of AWS. They run a single PCS 5 mhz WCDMA 3G carrier and the rest of the PCS is GSM. Their 700A Band 12 will be limited to about 3x3mhz FDD-LTE when they deploy later.
ATT has quite a mishmash of spectrum. 12 mhz of 700B Band 17 (5x5 mhz FDD-LTE), 700D block Band 29 which is unpaired and unusable, the Cell 850 A block, 10mhz of AWS good for 5x5 FDD-LTE on Band 4, and 20 mhz of PCS A + D which is split for numerous WCDMA 3G + GSM carriers. So they're probably going to run AWS LTE and aggregate it with their 700B block LTE and then moving onto refarming PCS carriers later. IE -a nightmare.
Take your poison.
I'm not in your area, but Ting has been swell for me in Minnesota. Sprint's coverage map shows NO LTE in the Twin Cities of Minneapolis & St. Paul, though it exists well to the west in rural MN. Imagine my surprise to get it at my home in Hopkins, at least 75 miles away from Sprint's nearest report of coverage. Phone service is unchanged from when I was a Sprint customer.
SomeTing wong
Sent from my Nexus 5
Yes som ting is wong
Firstly it looks like when you got your service you only provided them the ESN number which they can provide you 3G and 1X
however you need a sprint 4G lte sim to actually get LTE along with 3G and 1X ask ting about it.
Hello,
My girlfriend and I are on Koodo network (a Telus MVNO) and we have issue with signal reception in our house. Both phones were getting good signal with others carriers (Rogers and Videotron). According to the coverage map at the Koodo store, we should get strong LTE/HSPA signal in our neighborhood, which is the case, but unfortunately when we are inside our house, the signal drop to -110dBm (0-1 bar) and even no signal at all in some areas of the house. We get descent signal reception right outside our house (around -80dBm 3-4 bars).
What I would like to do is to take that signal from the outside and bring it inside the house so we can use our cell phones at home and get rid of our land line. I need your help to determine which repeater/booster I should use. We don't really care having LTE data inside the house because we already have high-speed internet trough a wifi router, only being able to make/receive calls would be fine.
I'm looking for something priced below 200$-250$. I can do the installation myself without any problem (i.e installing an antenna on the roof if required). I found that one: http://www.tigerdirect.com/applications/SearchTools/item-details.asp?EdpNo=8950334&CatId=4977
not sure if it suited for our needs. Afaik, Koodo use 800/1900 MHz for HSPA and 1700/2100 for LTE
Any suggestions/personal experience/advices would be appreciated. Changing carrier is not an option atm.
Yep,just install a booster,it'll help.
Spoiler
I provide support in Q&A and Kindle Fire HD sections. Xbox:computernerd888. I'm currently applying for Forum Ambassador on there. MCPE:TechGuy341523,R3kTtechMC or r3kt_iSuck3r.
Hi guys recently I bought an unlocked g955u1 from best buy and am on Verizon. I've noticed that my cell signal has been reading a bit off despite doing the Verizon software update. My phone is almost always stuck on 3 bars lte according to lte discovery and the range of dBm will average -100 to as low as -108 which realistically should be 1-2 bars not 3. In the past the only time I've really saw inaccurate readings like this is when I've been on gsm carriers. It's not as much as a problem as more of an annoyance as everything works fine. My question is anybody know why it's reading so inaccurate?
The bars are more or less just approximate visualizations of the network strength anyway. It varies from carrier to carrier, as well as phone manufacturer. You're better off sticking with the dB display if you want a truly accurate reading. Imho.
I have a T-Mobile variant and have noticed the my DL and UL speeds are a lot faster than any of the phone I've had in the past. We live out from town and even on the Nexus 6 it shows 3 bars and on the S8+ I get all the bars and the DL speed on the other phones at my house are around 5Mbps and on the S8+ I get 17-20Mbps at the house now. In town it has gone up from 40Mbps to 55Mbps.
My ATT S8+ reception
While I agree that the dBm is what you should be looking at, I have noticed some funky things going on with my ATT S8+ in terms of reception. Using the same SIM card, placing the phone in the exact same place, my S6 Active has a signal strength of -124 dBm /asu 16/"In service" on LTE. The S8+ gets a signal strength of -113 dBm/asu of 0/"Out of service." To me this seems like the S8+ is actually getting better reception than the 6S Active but the phone is out of service. I also tried this same test in another location using a different cell tower. Same results, the S8+ gets better reception...but the phone does not perform as well. In location number 2 I have also notice the S8+ fish for better signal and switch from LTE to HSPA where the signal strength is -99 dBm but the asu is only 7.
Since I live in a area with weak cell coverage the S8+ is driving me nuts...I contacted ATT about it last night, will see what happens.
Also somewhat related:
I'm using a US Unlocked on T-Mobile, and I've noticed my signal dropping out in areas where I previously had great signal on my Pixel XL. My buddy (also on T-Mo) just got an LG G6 and had full signal when mine dropped out.
Anyone else notice a weak signal? If I flash the T-Mo firmware, will that improve my signal? Did I get a bad unit? I hope not as everything else is perfect, screen included.
i notice (with TMobile) that if i am in 4g lte, then move to area with only edge for a few mins, then back to the 4g lte area...my phone doesn't connect back to the best signal
only a reboot let's me reconnect to 4g lte