This is a tried and tested method and it does work. This worked for me when EVERYTHING else failed and that includes MTK tools, mobile uncle tools, reflashing signed stock rom innumerable times. Thankyou @Chrizzly92 for this!!!
Follow this method this will surely work! Kudos to the developers!!:good:
IMPT YOU NEED TO HAVE A ROOTED PHONE SINCE YOU NEED TO PASTE A FILE IN THE /data/nvram FOLDER.
So first follow this section [Format EMMC with SP Flash Tool (Full Format)] with the help of the guide made by @codelover for honor 3c and then reflash your phone with the signed B108 international ROM. Then root your phone by the following method
Unlock your bootloader using the method given in the guide, then flash a custom recovery through spft and flash UPDATE-SuperSU-v2.40.zip attached with this post with the help of the custom recovery.
After following the above method, download ES File Explorer from play store and grant it superuser privileges.
NOW THE METHOD TO RESTORE YOUR IMEI
1. Download the attached imei.zip and extract it.
2. Run imei generator.bat
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3. Find your IMEI numbers on your phone product box or remove the battery of your phone and you'll find the IMEI numbers written there.
Then input your IMEI numbers in the command prompt window which is opened by imei generator.bat
4. A file will get generated in the folder where the bat file is located.
5. Now transfer the generated file onto your sd card or your internal sd card. Copy the file and navigate to /data/nvram/md/NVRAM/NVD_IMEI/ and replace the MP0B_001 file with your generated MP0B_001 file.
6. Restart your phone and wait for a few seconds and VOILA!! Networks have been restored!!:victory:
7. Now to make this fix permanent (yeah, up till now this was a temporary fix i.e. IMEI will again be lost after a factory reset), flash the UPDATE-ModemFix-MY.zip attached with this post through the custom recovery and reboot.
DONE!! :victory: Now your IMEI has been fully restored and will remain intact even if you factory reset your phone or flash a new ROM. And by chance if u break the IMEI again, follow the above steps again!
Feel free to ask any questions regarding this issue . This saved my ass BIG TIME!! THANKYOU TO THE BLESSED SOULS WHO DEVELOPED THIS GENERATOR and the guide by @codelover!! And hit thanks if this post helped you
worked
thank you.:good:
softroid said:
worked:good:
thank you.:good:
Click to expand...
Click to collapse
Glad i could help
Very useful
worked for me
hulkinBrain said:
This is a tried and tested method and it does work. This worked for me when EVERYTHING else failed and that includes MTK tools, mobile uncle tools, reflashing signed stock rom innumerable times. Thankyou @Chrizzly92 for this!!!
Follow this method this will surely work! Kudos to the developers!!:good:
Click to expand...
Click to collapse
i did all steps but still have no antena and IMEI null.
[ROM][UNOFFICIAL][5.1.1][CM 12.1] Cyanogenmod 12.1 port for Huawei Honor 3C (H30-U10)
h_asadbeigi said:
i did all steps but still have no antena and IMEI null.
[ROM][UNOFFICIAL][5.1.1][CM 12.1] Cyanogenmod 12.1 port for Huawei Honor 3C (H30-U10)
Click to expand...
Click to collapse
did you format the EMMC? because the first time i hadnt and faced the same problem.
hulkinBrain said:
did you format the EMMC? because the first time i hadnt and faced the same problem.
Click to expand...
Click to collapse
Please tell me how to format emmc. I have no clue. Many thanks.
Honor 4x Che1-L04
Pls provide the same type of tools forHonor 4x Che1-L04 Indian edition.
dyy1969 said:
Please tell me how to format emmc. I have no clue. Many thanks.
Click to expand...
Click to collapse
Here, see this guide: http://forum.xda-developers.com/showpost.php?p=54603767&postcount=5
neerajksw said:
Pls provide the same type of tools forHonor 4x Che1-L04 Indian edition.
Click to expand...
Click to collapse
This is a general tool. it should work for honor 4x too.
hulkinBrain said:
This is a tried and tested method and it does work. This worked for me when EVERYTHING else failed and that includes MTK tools, mobile uncle tools, reflashing signed stock rom innumerable times. Thankyou @Chrizzly92 for this!!!
Follow this method this will surely work! Kudos to the developers!!:good:
IMPT YOU NEED TO HAVE A ROOTED PHONE SINCE YOU NEED TO PASTE A FILE IN THE /data/nvram FOLDER.
So first follow this section [Format EMMC with SP Flash Tool (Full Format)] with the help of the guide made by @codelover for honor 3c and then reflash your phone with the signed B108 international ROM. Then root your phone by the following method
Unlock your bootloader using the method given in the guide, then flash a custom recovery through spft and flash UPDATE-SuperSU-v2.40.zip attached with this post with the help of the custom recovery.
After following the above method, download ES File Explorer from play store and grant it superuser privileges.
NOW THE METHOD TO RESTORE YOUR IMEI
1. Download the attached imei.zip and extract it.
2. Run imei generator.bat
3. Find your IMEI numbers on your phone product box or remove the battery of your phone and you'll find the IMEI numbers written there.
Then input your IMEI numbers in the command prompt window which is opened by imei generator.bat
4. A file will get generated in the folder where the bat file is located.
5. Now transfer the generated file onto your sd card or your internal sd card. Copy the file and navigate to /data/nvram/md/NVRAM/NVD_IMEI/ and replace the MP0B_001 file with your generated MP0B_001 file.
6. Restart your phone and wait for a few seconds and VOILA!! Networks have been restored!!:victory:
7. Now to make this fix permanent (yeah, up till now this was a temporary fix i.e. IMEI will again be lost after a factory reset), flash the UPDATE-ModemFix-MY.zip attached with this post through the custom recovery and reboot.
DONE!! :victory: Now your IMEI has been fully restored and will remain intact even if you factory reset your phone or flash a new ROM. And by chance if u break the IMEI again, follow the above steps again!
Feel free to ask any questions regarding this issue . This saved my ass BIG TIME!! THANKYOU TO THE BLESSED SOULS WHO DEVELOPED THIS GENERATOR and the guide by @codelover!! And hit thanks if this post helped you
Click to expand...
Click to collapse
Thanks for this guide , I have done exactly this but when i factory reset my phone the imei go back to null any help I can get i'll be very grateful thanks in advance
yarob95 said:
Thanks for this guide , I have done exactly this but when i factory reset my phone the imei go back to null any help I can get i'll be very grateful thanks in advance
Click to expand...
Click to collapse
Just crossing out all the possible problems... you formated your emmc right?If not, it can create problems. Before applying the UPDATE Modem fix, did it temporarily fix your imei problem?
hulkinBrain said:
Just crossing out all the possible problems... you formated your emmc right?If not, it can create problems. Before applying the UPDATE Modem fix, did it temporarily fix your imei problem?
Click to expand...
Click to collapse
Thanks for reply,
I have formatted emmc (full format), flashed the b108 signed rom, unlocked the bootloader, installed twrp and rooted the phone, boot and the phone with no signals and imei null, created the MP0b file and put it in the sd , replaced it with the one in system files set permissions and reboot and the signals showed, then I flashed the my-modem and everything was good and signals were there, then I factory reset the phone and again back to imei null
I want to relock the bootloader again and leave this rom_messy thing :/
yarob95 said:
Thanks for reply,
I have formatted emmc (full format), flashed the b108 signed rom, unlocked the bootloader, installed twrp and rooted the phone, boot and the phone with no signals and imei null, created the MP0b file and put it in the sd , replaced it with the one in system files set permissions and reboot and the signals showed, then I flashed the my-modem and everything was good and signals were there, then I factory reset the phone and again back to imei null
I want to relock the bootloader again and leave this rom_messy thing :/
Click to expand...
Click to collapse
Backup your IMEI using MTK tools when you get the signals. Then instead of using UPDATE modem fix to make the changes permanent, use MTK tools to restore your IMEI.
Check if this method works for you
what on earth is a second imei? is that S/N?
Penetralia13 said:
what on earth is a second imei? is that S/N?
Click to expand...
Click to collapse
You do know it's a dual SIM phone right? One IMEI for each sim slot. Open your phone dialer and type *#06#, you'll see.
hulkinBrain said:
You do know it's a dual SIM phone right? One IMEI for each sim slot. Open your phone dialer and type *#06#, you'll see.
Click to expand...
Click to collapse
lol i do the problem is that after the flash i have no imeis and at the back of the phone only imei 1 is written
Penetralia13 said:
lol i do the problem is that after the flash i have no imeis and at the back of the phone only imei 1 is written
Click to expand...
Click to collapse
What?! You sure that you aren't looking at the serial number? There must be 2 IMEI numbers at the back of the phone which you'll be able to see after removing the battery. If for some reason there is only 1 IMEI number present, then enter the same IMEI number twice when the tool asks for the IMEI numbers.
hulkinBrain said:
What?! You sure that you aren't looking at the serial number? There must be 2 IMEI numbers at the back of the phone which you'll be able to see after removing the battery. If for some reason there is only 1 IMEI number present, then enter the same IMEI number twice when the tool asks for the IMEI numbers.
Click to expand...
Click to collapse
Will do cheers
Penetralia13 said:
Will do cheers
Click to expand...
Click to collapse
Do let me know if it worked or not
Related
Hi guys and girls!!!
peoples are always worried about getting their device bricked so that i m making this tut to recover ur phone in only 3 steps, u dont need any special hardware or dont need to dissemble ur phone u will just need a usb cable and windows pc
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
READ THIS FIRST
this method is dangerous as it will format the whole system and all the partitions on your phone. this will also format ur EFS partition so if ur using this tut for downgrading bootloader than its strongly warned that u backup ur EFS folder otherwise u will loose ur IMEI number.
this whole process will wipe ur internal sd card, there is no way to recover/backup it as in bricked phone u cant mount ur storage.
if u have 2.1 bootloader and want to downgrade it to v2.0 so that u can use usb jig to reset binary counter u can use this method but this method is risky so its recommended to backup all ur data and specially EFS folder to save ur IMEI number.
if u r on bootloader 2.0 and dont have usb jig and u want to reset ur download counter than u can use this method but as this method is risky so better buy usb jig and use it. use this as a last option. and dont forget to backup EFS and SD card otherwise u will loose ur IMEI and data stored on SD card.
BACKING UP EFS
there are many ways to backup/restore EFS partitions is out there but using efs backup pro is recommend, this tool works like charm. u will need to root ur phone first to backup ur EFS partition. (those who have bricked their phone, there is no way to backup ur efs in bricked phone so u will have to give ur phone in ssc to reprogram ur imei)
http://forum.xda-developers.com/showthread.php?t=1068193
some peoples says that after restoring backup made by efs backup pro their imei gets messed, they r unable to revert their original imei. if u have lil bit knowledge of ADB u can use this method its best method to backup imei.
http://forum.xda-developers.com/showthread.php?t=1308546
NOTE FOR ICS USERS.
This unbricking tool is working on ICS also. but after this tool completes flashing u wont be able to flash stock ROM via odin directly to solve this u have to do a lil change in process.
after unbricking tool completes flashing, remove usb cable and reboot ur phone. phone will automatically boot in download mod as its not having OS.
now open odin, plug in ur device and flash ur desired stock ROM.
(thanks to UnknownzD for finding this solution.)HOW TO DO THIS???
STEP 1: DOWNLOADING REPAIR PACKAGE AND SETTING UP DRIVERS
Download the attached zip file and extract it to any directory like "C:\\SGR" or whatever u want. now remove battery of ur phone and insert it. now press VOLUME UP, HOME, POWER KEY together and insert usb cable to pc. ur pc will detect hardware named APX.
now open device manager. (right click on my computer>properties>device manager). u will see APX named hardware with yellow triangle on it. double click it and select update driver. now select "BROWSE MY COMPUTER......." option and it will ask for directory chose the directory in which u have extracted repair package. windows will show u warning ignore it and select install driver anyway.now see device manager in serial bus tree it should display hardware named NVIDIA RECOVERY........
STEP 2: FLASHING THE WHOLE FILE SYSTEM/BOOTLOADER
now everything is set for flashing the bootloader to ur bricked phone. open extracted folder in that u will find a file named GTI9103.bat open it, u will see command prompt window. now connect ur phone in APX mode as described in step 1. (to confirm that ur device is connected in apx mode u can look in device manager for hardware named nvidia recovery..... under serial bus tree). now after connecting device type 1 in opened command prompt and hit enter. now this tool will start flashing on ur sgr. after flash ur phone will reboot and download mode will appear as device starts.
STEP 3: FLASHING STOCK ROM AND FORMATTING DATA PARTITION
now open odin flashing tool (i faced problem while falshing with odin 1.86 so i recommend to use attached odin 1.80). remove usb cable from phone and connect it again, odin will detect phone and yellow mark with com port should appear. now this is important. here u have to check "RE PARTITION" in odin and click "PIT" buttom in odind and choose "p5.pit" file from extracted folder. in pda select the stock fw u want to flash. now check odin for this things "re partision, auto reboot, reset time is checked. in pit selection pit file is selected and in pda ur desired fw is selected." after checking this hit start and wait till flash finish. After flash ur phone will boot and will show error that /data is not found and ur phone will stuck at bootloop. Don't worry its normal as the flashing process have wiped data partition and its not ready to be used by os so phone won't boot. To solve this just boot in recovery mode by holding VOL UP + HOME key at boot. (U can use both stock and cwm recovery) and format the data partition and reboot. Ur phone will boot now and will work perfectly.
If u have backup of EFS than root ur phone and restore ur efs folder so that u can recover ur IMEI number.
If u dont have efs backup dont worry. Simply give ur phone in ssc and claim that phone is not receiving network. They will fix it for free
(If ur warranty is over, they will charge u for this)CREDITSXiaoyuz for making this flashing tool.
F3nix for sending me this flashing package.
UnknownzD for testing this tool on ICS roms and finding a workaround for odin flashing problem on ICS.
Attachments:
Repair Package:http://www.4shared.com/zip/piwOOt1J/GT-I9103_Dead_Repair_By_Xiaoyu.html
Odin v1.00: http://www.4shared.com/zip/WjuuJ4-2/Odin3_v10.html?
I was using titanium 2.1 with unknown kernel. I m using titanium since 3 months and i never faced any prob with it. On sunday my phones got bricked and i havent used my phone that day much only for checking xda with tapatalk. I dont know how it got bricked its still a mistery and will be always.
Sent from my GT-I9103 using Tapatalk 2
Okay when i do this i can go to shop and ask for refund?
But problem is i unlocked it with a program. Normally net is locked to 3 Austria so could this be a problem?
Sent from my GT-I9103 using xda premium
pudup said:
If you made a backup of your efs folder, you won't need to go to the ssc since you just fixed it yourself
Sent from my GT-I9103 using XDA
Click to expand...
Click to collapse
fk i didnt back up before unlock...
Sent from my GT-I9103 using xda premium
using root explorer i've copied the EFS folder and stored it in my system is it enough or should i use any tool to backup EFS folder...
mj.vikram said:
using root explorer i've copied the EFS folder and stored it in my system is it enough or should i use any tool to backup EFS folder...
Click to expand...
Click to collapse
Copying via root explorer only backup files, permissions are not saved with the files. If you restore later, the permissions may conflict and the IMEI get messed up.
So, it is better to use tool such as EFS backup pro that also backup permissions.
Will this tutorial work for my only "USB Bricked" SGR? If yes, then which steps should I follow?
Actual matter:-
-Doesn't charge via a wall charger nor USB cable.
-Download mode accessible.
-Reverted back to Stock Indian ROM as well as stock recovery.
-Doesn't detect on any PC. Also tried MAC. Not even in download mode.
-Can't charge at all. Have to charge my battery by putting it in my Sister's S2.
All i did was google for the zip. Glad I could help..
Sent from my GT-I9103 using XDA
@ OP
Thnx a ton buddy....
Ready guides to evacuate from every possible nightmare is a big support for the beginners like me.... Although my sgr is safe yet but its encouraging... thnx again
Sent from my GT-I9103
Great writeup! This thread has been STUCK!
Red5 said:
Great writeup! This thread has been STUCK!
Click to expand...
Click to collapse
thanks a lot
xlm13x said:
thanks a lot
Click to expand...
Click to collapse
i am getting on wiping cache screen
azhar.munshi said:
i am getting on wiping cache screen
Click to expand...
Click to collapse
i am getting screen of updating package
xlm13x said:
thanks a lot
Click to expand...
Click to collapse
i am stucking on recovery page can anyone guide me urgently
---------- Post added at 11:12 AM ---------- Previous post was at 10:16 AM ----------
xlm13x said:
Hi guys and girls (yes we do have girl member here ).
i have bricked my sgr yesterday and with help of some users and XDA i managed to repair it. peoples are always worried about getting their device bricked so that i m making this tut to recover ur phone in only 3 steps, u dont need any special hardware or dont need to dissemble ur phone u will just need a usb cable and windows pc
if u have 2.1 bootloader and want to downgrade it to v2.0 so that u can use usb jig to reset binary counter u can use this method but this method is risky so its recommended to backup all ur data and specially EFS folder to save ur IMEI number.
if u r on bootloader 2.0 and dont have usb jig and u want to reset ur download counter than u can use this method but as this method is risky so its not recommended to use this better buy usb jig and use it. use this as a last option.
READ THIS FIRST
this method is dangerous as it will format the whole system and all the partitions on your phone. this will also format ur EFS partition so if ur using this tut for downgrading bootloader than its strongly warned that u backup ur EFS folder otherwise u will loose ur IMEI number.
this whole process will wipe ur internal sd card, there is no way to recover/backup it as in bricked phone u cant mount ur storage.
STEP 1: DOWNLOADING REPAIR PACKAGE AND SETTING UP DRIVERS
Download the attached zip file and extract it to any directory like "C:\\SGR" or whatever u want. now remove battery of ur phone and insert it. now press VOLUME UP, HOME, POWER KEY together and insert usb cable to pc. ur pc will detect hardware named APX.
now open device manager. (right click on my computer>properties>device manager). u will see APX named hardware with yellow triangle on it. double click it and select update driver. now select "BROWSE MY COMPUTER......." option and it will ask for directory chose the directory in which u have extracted repair package. windows will show u warning ignore it and select install driver anyway.now see device manager in serial bus tree it should display hardware named NVIDIA RECOVERY........
STEP 2: FLASHING THE WHOLE FILE SYSTEM/BOOTLOADER
now everything is set for flashing the bootloader to ur bricked phone. open extracted folder in that u will find a file named GTI9103.bat open it, u will see command prompt window. now connect ur phone in APX mode as described in step 1. (to confirm that ur device is connected in apx mode u can look in device manager for hardware named nvidia recovery..... under serial bus tree). now after connecting device type 1 in opened command prompt and hit enter. now this tool will start flashing on ur sgr. after flash ur phone will reboot and download mode will appear as device starts.
STEP 3: FLASHING STOCK ROM AND FORMATTING STORAGE
now open odin flashing tool (i faced problem while falshing with odin 1.86 so i recommend to use attached odin 1.80). remove usb cable from phone and connect it again, odin will detect phone and yellow mark with com port should appear. now this is important. here u have to check "RE PARTITION" in odin and click "PIT" buttom in odind and choose "p5.pit" file from extracted folder. in pda select the stock fw u want to flash. now check odin for this things "re partision, auto reboot, reset time is checked. in pit selection pit file is selected and in pda ur desired fw is selected." after checking this hit start and wait till flash finish. After flash ur phone will boot and will show error that /data is not found. Dont worry just aftet boot format ur internal sd (if u use pc than format it wit fat32 file system) and reboot now u have a perfect running device with no network as ur efs is wiped in this process.
If u have backup of EFS than root ur phone and restore ur efs folder so that u can recover ur IMEI number.
If u dont have efs backup dont worry. Simply give ur phone in ssc and claim that phone is not receiving network. They will fix it for free
CREDITSXiaoyuz for making this flashing tool.
F3nix for sending me this flashing package.
Attachments:
Repair Package:http://www.4shared.com/zip/piwOOt1J/GT-I9103_Dead_Repair_By_Xiaoyu.html
Odin v1.00: http://www.4shared.com/zip/WjuuJ4-2/Odin3_v10.html?
Click to expand...
Click to collapse
i had update repartition & firmware also but after that it going to recovery page but does not going ahead it stucks on same page
---------- Post added at 11:52 AM ---------- Previous post was at 11:12 AM ----------
how to format internalsd
my phone going in recovery page
azhar.munshi said:
how to format internalsd
my phone going in recovery page
Click to expand...
Click to collapse
Have you flashed the Pit file and stock firmware with the help of ODIN.
mj.vikram said:
Have you flashed the Pit file and stock firmware with the help of ODIN.
Click to expand...
Click to collapse
i had solved but now my imei is not working i didnt saved efs folder
can anyone guide me how i can resolve this issue
azhar.munshi said:
i had solved but now my imei is not working i didnt saved efs folder
can anyone guide me how i can resolve this issue
Click to expand...
Click to collapse
OK Good at least its booting now, no one can help you in this you need to take it to Samsung Service Center and tell them that all of sudden my phone is not working properly and network is not there....
Before doing this make sure you are on stock ROM and without CWM flashed on the device...
A question -> Does the unbrick process require downgrading bootloader? I suppose not. Correct me if I am wrong.
And if not, can xlm13x separate the two processes of downgrading for resetting counter with usb jig and unbricking the phone. Currently it looks a little confusing.
Also, anyone who has just bricked his phone may be a bit panicked and may not be paying full attention.
Just a thought. You may choose to ignore
Sent from my GT-I9103 using XDA
Downgrading bootloader and unbricking are actually same things, if u follow steps of this post actually it wipes the whole system parttition (the whole root folder, including efs and bootloader). And than it writes it back but it will write bootloader 2.0.
So in both cases (unbrick, downgrade bootloader) will have to follow the same process that's y I created this 2in1 thread.
Sent from my GT-I9103 using Tapatalk 2
hi
will it work for samsung galaxy i5503 ?
Phone: Cherry Mobile Titan (Rebrand of Konka w990/Spice-mi 500/Axioo Picopad GEW)
Processor: MTK6577
Hello guys, this is my first post as I could no longer find any solution on the internet. Hoping some experts could help
I accidentally formatted the NVRAM of my phone using SP Flash Tool. The new update didn't have the option not to format it. Now my IMEI's are lost. Although it is still possible to restore them using some methods. But none of the methods I have found were permanent. A simple wipe/data factory reset from CWM Recovery removes it instantly. Is there a way I could restore the NVRAM, or at least make the restoration methods permanent?
Thanks in advance guys!
EDIT: I tried flashing all available ROMs (SP Flash Tool Based / Flashable Zips) but still it shows an invalid IMEI. I also tried restoring a backup of my stock ROM to no avail.
ToldarkenHansam said:
Phone: Cherry Mobile Titan (Rebrand of Konka w990/Spice-mi 500/Axioo Picopad GEW)
Processor: MTK6577
Hello guys, this is my first post as I could no longer find any solution on the internet. Hoping some experts could help
I accidentally formatted the NVRAM of my phone using SP Flash Tool. The new update didn't have the option not to format it. Now my IMEI's are lost. Although it is still possible to restore them using some methods. But none of the methods I have found were permanent. A simple wipe/data factory reset from CWM Recovery removes it instantly. Is there a way I could restore the NVRAM, or at least make the restoration methods permanent?
Thanks in advance guys!
EDIT: I tried flashing all available ROMs (SP Flash Tool Based / Flashable Zips) but still it shows an invalid IMEI. I also tried restoring a backup of my stock ROM to no avail.
Click to expand...
Click to collapse
I'm in same case. I accidently damage my nvram ;
i have a complet backup made with mtkdroid tools (nvram included)
but sp flash tool doent give option to restore this part? how to restore?
the same problem for me. The phone is fully working, but it is very annoying to restore imei and delete wifi network (NVRAM WARNING err...) after each new ROM. And also I cannot sell this phone to anybody in the future.
No solution for this problem?
somebody can write commenttt???
---------- Post added at 07:54 AM ---------- Previous post was at 07:48 AM ----------
hey guys .at this picture error how can i solve this error?
h t t p : / /u1306.hizliresim.com/1b/l/p975s.jpg
first, you`ll need to root your device. refer to here:
http://forum.xda-developers.com/showthread.php?t=2332783
follow the tutorial step by step, if you brick your device i will laugh at you. if you got questions, ask them before doing random stuff.
if you got it rooted, you can recover your IMEI with different software. i will link one in this post later.
for questions - use this thread or PM me.
ToldarkenHansam said:
Phone: Cherry Mobile Titan (Rebrand of Konka w990/Spice-mi 500/Axioo Picopad GEW)
Processor: MTK6577
Hello guys, this is my first post as I could no longer find any solution on the internet. Hoping some experts could help
I accidentally formatted the NVRAM of my phone using SP Flash Tool. The new update didn't have the option not to format it. Now my IMEI's are lost. Although it is still possible to restore them using some methods. But none of the methods I have found were permanent. A simple wipe/data factory reset from CWM Recovery removes it instantly. Is there a way I could restore the NVRAM, or at least make the restoration methods permanent?
Thanks in advance guys!
EDIT: I tried flashing all available ROMs (SP Flash Tool Based / Flashable Zips) but still it shows an invalid IMEI. I also tried restoring a backup of my stock ROM to no avail.
Click to expand...
Click to collapse
I think your phone is dead. Is the phone detected when you plug it in to your pc via USB?
phone isn't dead. root it first, recovering imei is easy then. cannot explain more, im on smartphone right now.
sent from my Star N9770 using XDA App
so, here is a tool to generate the IMEI`s of your smartphone. you will usually find them in the back of your device. push the generated file to /data/nvram/md/NVRAM/NVD_IMEI/ and DON'T FORGET TO SET FULL RWX rights. (with ADB, cd to the mentined folder and set MP0B_001 with chmod to mode 777, in root explorer just check every box for read write and execute. otherwise phone cannot read the IMEI.
What a lame answers. Especially ones suggesting to root phone.
They guy clearly told he is able to restore MP0B_001 in phone, but its SOFT-IMEI and is lost after wipe/factory reset.
@ Original question by ToldarkenHansam, which is kinda outdated, but considering lame answers here:
To restore HARD-IMEI in NVRAM hidden partition use SN Write Tool or Maui META 3G. They are able to write hard IMEI and calibration to NVRAM partition.
@ kokabunga - if you have nvram.bin backup you can easily resore it with SP Flash Tool. Just open your scatter file with any text editor, find a __NODL_NVRAM section and remove __NODL_ part from it. Reopen scatter in SP Flash Tool and you'll be able to check NVRAM partition.
It might not be able to upload it without other parts selected. But you can you Options->Write memory, then manually enter start address, which will be show on download/upgrade page near NVRAM and length (your nvram.bin length) - that will always work. Be careful to write correct address thou.
Sidenote: all suggested methods before only touch SOFT-IMEI, stored in /data/nvram/md/NVRAM/NVD_IMEI/MP0B_001. Its lost with any wipe/reset, because whole /data partition are formatted. Then the whole /data/nvram directory (if it's empty) are restored from hidden NVRAM partition on EMMC. If you've corrupted your NVRAM when it won't restore correct IMEI ofc. With all methods mentioned above (i.e. replacing MP0B_001, echoing to pttycmd1, using mtkdroidtools, mobileuncletools and others) will only edit MP0B_001, i.e. soft copy of IMEI, which will be lost again with next hardware reset. Sure you restore your IMEI that way every time you wipe/reset/upgrade firmware. But its more solid to fix your IMEI partition with SN Write Tool / Maui META 3G so it will be correctly restored automatically from NVRAM at every wipe/etc.
EDIT: @Chrizzly92 this software are very outdate. It generates 24 byte MP0B_001 file, used by old MT6573/6513 platforms. Newer 6575/6577 uses 120 bytes MP0B_001 which are different. If you put 24 byte MP0B_001 generated instead from imei.c software, your phone will be buggy and will be constantly loosing IMEI every few hours until reboot. It's better to use MtkDroidTools or terminal method (echoing to /dev/pttycmd1) to correctly restore 120 byte IMEI file.
n9770, mt6577, no problem at all with the generated files.
sent from my Star N9770 using XDA App
same thing happened to me.. only sn write tool maybe able to do the job..I have also lost wifi mac address..now getting nv110 error..
but I need database and modem files for xolo a700 can anyone help?
NStorm said:
What a lame answers. Especially ones suggesting to root phone.
They guy clearly told he is able to restore MP0B_001 in phone, but its SOFT-IMEI and is lost after wipe/factory reset.
@ Original question by ToldarkenHansam, which is kinda outdated, but considering lame answers here:
To restore HARD-IMEI in NVRAM hidden partition use SN Write Tool or Maui META 3G. They are able to write hard IMEI and calibration to NVRAM partition.
@ kokabunga - if you have nvram.bin backup you can easily resore it with SP Flash Tool. Just open your scatter file with any text editor, find a __NODL_NVRAM section and remove __NODL_ part from it. Reopen scatter in SP Flash Tool and you'll be able to check NVRAM partition.
It might not be able to upload it without other parts selected. But you can you Options->Write memory, then manually enter start address, which will be show on download/upgrade page near NVRAM and length (your nvram.bin length) - that will always work. Be careful to write correct address thou.
Sidenote: all suggested methods before only touch SOFT-IMEI, stored in /data/nvram/md/NVRAM/NVD_IMEI/MP0B_001. Its lost with any wipe/reset, because whole /data partition are formatted. Then the whole /data/nvram directory (if it's empty) are restored from hidden NVRAM partition on EMMC. If you've corrupted your NVRAM when it won't restore correct IMEI ofc. With all methods mentioned above (i.e. replacing MP0B_001, echoing to pttycmd1, using mtkdroidtools, mobileuncletools and others) will only edit MP0B_001, i.e. soft copy of IMEI, which will be lost again with next hardware reset. Sure you restore your IMEI that way every time you wipe/reset/upgrade firmware. But its more solid to fix your IMEI partition with SN Write Tool / Maui META 3G so it will be correctly restored automatically from NVRAM at every wipe/etc.
EDIT: @Chrizzly92 this software are very outdate. It generates 24 byte MP0B_001 file, used by old MT6573/6513 platforms. Newer 6575/6577 uses 120 bytes MP0B_001 which are different. If you put 24 byte MP0B_001 generated instead from imei.c software, your phone will be buggy and will be constantly loosing IMEI every few hours until reboot. It's better to use MtkDroidTools or terminal method (echoing to /dev/pttycmd1) to correctly restore 120 byte IMEI file.
Click to expand...
Click to collapse
Greetings NStorm i try your method i already got one backup with MTKDROID TOOLS so i can use the NVRAM.BIN , i already modify scatter file and try to write memory but i only receive red bar, no yellow or green, so i think it not work at all, any suggestions also sorry for my bad english im from Mexico, ohhh i forgot i already have a full backup from all the files in the smartphone do you know if i can FLASH the Full Backup back? or a CWM restore or other kind of solution?
foox2k said:
Greetings NStorm i try your method i already got one backup with MTKDROID TOOLS so i can use the NVRAM.BIN , i already modify scatter file and try to write memory but i only receive red bar, no yellow or green, so i think it not work at all, any suggestions also sorry for my bad english im from Mexico, ohhh i forgot i already have a full backup from all the files in the smartphone do you know if i can FLASH the Full Backup back? or a CWM restore or other kind of solution?
Click to expand...
Click to collapse
NStorm, thanks for your awesome explanation.
I do not fully understand the nvbin flashing part.
I also have a backup I believe, but I am unsure.
I do have a proper nvram backup, so the proper files that are overwritten on flash.
With SP flash tool I get error 8038 when trying to flash.
Firmware upgrade is not working either even with all partitions.
I tried to remove __NODL__ from the nvram to fix it, but no luck.
Can you explain how to make that imei file and flash it with dd command or anything?
Would be awesome to get this problem fixed!
thank you
[update]guess what, you can do it with mtk droid tools 2.4.8 too!
I tried that before, but I used a backup I made after the issue.
Found an older one and it seems to work![/update]
guys..for permanent nvram, imei error or invalid use sn write tools.
mine solve a long ago..please read this: http://forum.xda-developers.com/showthread.php?t=2206421
http://forum.xda-developers.com/showthread.php?t=2197378&page=3
btw use a complete sn write tool
well works for me ,after factory reset everthing still as writen..
my phone mtk 6577 chipset based
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Phone is Dead (canvas 2)
ToldarkenHansam said:
Phone: Cherry Mobile Titan (Rebrand of Konka w990/Spice-mi 500/Axioo Picopad GEW)
Processor: MTK6577
Hello guys, this is my first post as I could no longer find any solution on the internet. Hoping some experts could help
I accidentally formatted the NVRAM of my phone using SP Flash Tool. The new update didn't have the option not to format it. Now my IMEI's are lost. Although it is still possible to restore them using some methods. But none of the methods I have found were permanent. A simple wipe/data factory reset from CWM Recovery removes it instantly. Is there a way I could restore the NVRAM, or at least make the restoration methods permanent?
Thanks in advance guys!
EDIT: I tried flashing all available ROMs (SP Flash Tool Based / Flashable Zips) but still it shows an invalid IMEI. I also tried restoring a backup of my stock ROM to no avail.
Click to expand...
Click to collapse
i have selected "whole format" option in format tab in sp tools. but doing this my phone got dead. pls help me
Revived your ZTE V793 now!
Ok guys..
I'll share to you my ROM for flashing using SP Flash Tools application.
Note: I'll not take any responsibility for any damage, warranty void to your phone
1. Download SP Flas Tools - find it in xda or Google..
2. Download this ROM : This is backup ROM porting to my android device kindly remove in-necessary applications. As it's ready to flash via SP FLASH Tools so basically it'll be straight forward thing. Link here :
HTML:
[URL="http://www.4shared.com/archive/iBNm1jxI/V793_Files_to_FlashTool.html"]V793[/URL]
Password :
[email protected]
3. Extract the file using 7zip. Then extract the ZIP file inside.
4. Open SP_Flash_Tools.. select the extracted files earlier and select the scatter file.
5. Everything will be pick automatically.
6. Take your phone battery. Press start and wait "Searching" and connect your Phone (without battery) using USB.
7. Make sure you have the driver. Installed the driver if necessary.
8. Wait until you get "Doughnut" OK button. Warning : Never disconnect the cable during this operation as it'll brick your phone forever.
9. Once, OK. please disconnect your cable. Put the battery into the phone.
10. Make sure the battery at-least 80% before you perform the CWM steps.
Good Luck! If you need any further guide please revert here.. I'll try to create another 'empty' ROM after this if there is a request. Thanks.
---------- Post added at 04:23 AM ---------- Previous post was at 04:15 AM ----------
rohitjaiswal said:
i have selected "whole format" option in format tab in sp tools. but doing this my phone got dead. pls help me
Click to expand...
Click to collapse
Hi there..
before perform any update please... and please backup your ROM.. that's the reason "MTKdroidtools" being develop.
Use the application to gain "temp" root to able you to get the image files.
Then create SP Flash ready files from the backup image files.
If you don't have the backup ROM don't be hesitate to search it in google and XDA forum.. if your phone is "unique" please ask your friend. Loan the phone for a few minutes to make a backup images.
NStorm said:
What a lame answers. Especially ones suggesting to root phone.
They guy clearly told he is able to restore MP0B_001 in phone, but its SOFT-IMEI and is lost after wipe/factory reset.
@ Original question by ToldarkenHansam, which is kinda outdated, but considering lame answers here:
To restore HARD-IMEI in NVRAM hidden partition use SN Write Tool or Maui META 3G. They are able to write hard IMEI and calibration to NVRAM partition.
@ kokabunga - if you have nvram.bin backup you can easily resore it with SP Flash Tool. Just open your scatter file with any text editor, find a __NODL_NVRAM section and remove __NODL_ part from it. Reopen scatter in SP Flash Tool and you'll be able to check NVRAM partition.
It might not be able to upload it without other parts selected. But you can you Options->Write memory, then manually enter start address, which will be show on download/upgrade page near NVRAM and length (your nvram.bin length) - that will always work. Be careful to write correct address thou.
Sidenote: all suggested methods before only touch SOFT-IMEI, stored in /data/nvram/md/NVRAM/NVD_IMEI/MP0B_001. Its lost with any wipe/reset, because whole /data partition are formatted. Then the whole /data/nvram directory (if it's empty) are restored from hidden NVRAM partition on EMMC. If you've corrupted your NVRAM when it won't restore correct IMEI ofc. With all methods mentioned above (i.e. replacing MP0B_001, echoing to pttycmd1, using mtkdroidtools, mobileuncletools and others) will only edit MP0B_001, i.e. soft copy of IMEI, which will be lost again with next hardware reset. Sure you restore your IMEI that way every time you wipe/reset/upgrade firmware. But its more solid to fix your IMEI partition with SN Write Tool / Maui META 3G so it will be correctly restored automatically from NVRAM at every wipe/etc.
EDIT: @Chrizzly92 this software are very outdate. It generates 24 byte MP0B_001 file, used by old MT6573/6513 platforms. Newer 6575/6577 uses 120 bytes MP0B_001 which are different. If you put 24 byte MP0B_001 generated instead from imei.c software, your phone will be buggy and will be constantly loosing IMEI every few hours until reboot. It's better to use MtkDroidTools or terminal method (echoing to /dev/pttycmd1) to correctly restore 120 byte IMEI file.
Click to expand...
Click to collapse
i have imei problem , i have tried all of ways to write/restore/repair imei but failed. i have radio problem. System/dev/radio/pttycmd1
Radio is empty. there is no pttycmd1 so i can't writ imei . please tell how i can restore pttycmd1 or whole radio restore on my device ?
is it possible ? please please reply me soon. thanks,
[email protected]:crying:
Solution of NVRAM.img and no-services Lenovo S820
javedsipra said:
i have imei problem , i have tried all of ways to write/restore/repair imei but failed. i have radio problem. System/dev/radio/pttycmd1
Radio is empty. there is no pttycmd1 so i can't writ imei . please tell how i can restore pttycmd1 or whole radio restore on my device ?
is it possible ? please please reply me soon. thanks,
[email protected]:crying:
Click to expand...
Click to collapse
Solution of NVRAM.img and no-services Lenovo S820...thanks
foox2k said:
Greetings NStorm i try your method i already got one backup with MTKDROID TOOLS so i can use the NVRAM.BIN , i already modify scatter file and try to write memory but i only receive red bar, no yellow or green, so i think it not work at all, any suggestions also sorry for my bad english im from Mexico, ohhh i forgot i already have a full backup from all the files in the smartphone do you know if i can FLASH the Full Backup back? or a CWM restore or other kind of solution?
Click to expand...
Click to collapse
if you have CWM backup so you can install CWM on your phone and make a backup of current OS, then put the CWM backup in it and restore it.
if you have MTK Droid tools backup then you first make a flash able backup by choosing MD5 file from the backup. then it makes a new folder !file_to_flashtools . this is your flash able backup with scatter file.
Open MTK flashtools and select the scatter file and choose download or upgrade firmware which you like. connect the PC with battery or without battery , choose the options for battery.
make sure your android adb interface driver and preloader driver and cdc drivers are installed ?
how to install drivers ?
on your phone and select development and check debugging option and connect with PC. PC install drivers automatically if you have windows 7 . stop that process and install drivers manually . second time switch off your device put the battery out for 15 sec and put it again but no phone on. just off mode. connect with pc and install its preloader driver. Now press the power button continuously on phone device its ask for CDC drivers. install it and now your drivers are done.
for further detail contact on [email protected]
NStorm said:
What a lame answers. Especially ones suggesting to root phone.
They guy clearly told he is able to restore MP0B_001 in phone, but its SOFT-IMEI and is lost after wipe/factory reset.
@ Original question by ToldarkenHansam, which is kinda outdated, but considering lame answers here:
To restore HARD-IMEI in NVRAM hidden partition use SN Write Tool or Maui META 3G. They are able to write hard IMEI and calibration to NVRAM partition.
@ kokabunga - if you have nvram.bin backup you can easily resore it with SP Flash Tool. Just open your scatter file with any text editor, find a __NODL_NVRAM section and remove __NODL_ part from it. Reopen scatter in SP Flash Tool and you'll be able to check NVRAM partition.
It might not be able to upload it without other parts selected. But you can you Options->Write memory, then manually enter start address, which will be show on download/upgrade page near NVRAM and length (your nvram.bin length) - that will always work. Be careful to write correct address thou.
Sidenote: all suggested methods before only touch SOFT-IMEI, stored in /data/nvram/md/NVRAM/NVD_IMEI/MP0B_001. Its lost with any wipe/reset, because whole /data partition are formatted. Then the whole /data/nvram directory (if it's empty) are restored from hidden NVRAM partition on EMMC. If you've corrupted your NVRAM when it won't restore correct IMEI ofc. With all methods mentioned above (i.e. replacing MP0B_001, echoing to pttycmd1, using mtkdroidtools, mobileuncletools and others) will only edit MP0B_001, i.e. soft copy of IMEI, which will be lost again with next hardware reset. Sure you restore your IMEI that way every time you wipe/reset/upgrade firmware. But its more solid to fix your IMEI partition with SN Write Tool / Maui META 3G so it will be correctly restored automatically from NVRAM at every wipe/etc.
EDIT: @Chrizzly92 this software are very outdate. It generates 24 byte MP0B_001 file, used by old MT6573/6513 platforms. Newer 6575/6577 uses 120 bytes MP0B_001 which are different. If you put 24 byte MP0B_001 generated instead from imei.c software, your phone will be buggy and will be constantly loosing IMEI every few hours until reboot. It's better to use MtkDroidTools or terminal method (echoing to /dev/pttycmd1) to correctly restore 120 byte IMEI file.
Click to expand...
Click to collapse
your method of writing memory manually worked for me to bring back my /dev/radio folder and its contents, still cwmr write my imei though
This is to show you how to get Google Play on the Huawei Enjoy 5, which standard Chinese Stock ROM does not have Play store enabled.
Note: when unlocking the phone and installing custom recovery, it might mean that the OTA updates don't work anymore.
Since we have not yet had an update since I installed this, I could not check, but this is what is said in the Huawei unlock site...
Credits: my sincere thanks to andrik22, who guided me through the whole process...
Prerequisites:
Huawei Enjoy 5 phone (TIT-AL00)
Huawei Unlock tool (attached)
ADB drivers (attached)
ADB / Fastboot software (attached)
CWM Recovery file (attached)
GAPPS Pico for ARM64, Android 5.1 --> Download from Opengapps.org
Steps to complete:
1. Install ADB Drivers
2. Unzip ADB software in C:\adb
3. Unzip CWM_Recovery.img in C:\adb
4. Copy the GAPPS file into C:\adb
C:\adb should look like this now:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
5. Now got to the phone and write down:
Settings -->about phone --> Status--> IMEI 1 + Serial Number
6. Connect phone by USB to computer
7. Enable USB debugging on phone --> slide down the notification area and touch "USB connection options", then on the bottom of the screen enable "USB Debugging"
7a. Copy the GAPPS file from C:\adb to the root of the external SD card on your phone
8. Unzip and open the Unlock tool (you might need to disable the virus checker, as this will be flagged and deleted, at least this was the case with me) --> fill in IMEI 1, get Product ID, write that down.
9. Go to the Huawei site to get your unlock code (log in with Facebook, or Huawei ID, fill in the required information product type = Smartphone, product ID = TIT-AL00, serial number from the phone, IMEI code, Product ID). Your unlock code will be below in Red)
10. Startup command prompt (Windows key + R, type cmd, enter)
11. In command prompt, type "cd \adb" to get to the adb directory
12. In command prompt check if device is recognized (typing "adb devices" in the command prompt should show you this)
13. Now reboot the phone into fastboot by typing "adb reboot bootloader"
14. This should reboot the phone into fastboot mode (black screen, only showing "fastboot>" on the bottom
15. In the command prompt, type "fastboot devices" to see if the device is recognized.
Your screen should look something like this:
The next command will unlock your phone AND make a hard reset... if any data or settings would need to be preserved, please make a backup!
16. Now type in the command prompt:"fastboot oem unlock XXXXX" where XXXX is the unlock code you got from the website
17. Then type in command prompt: "fastboot reboot". After this, your phone will reboot and reset.
18. When Phone is rebooted, make sure USB debugging is on again (same as point 7)
19. Now reboot the phone into fastboot by typing "adb reboot bootloader"
20. This should reboot the phone into fastboot mode (black screen, only showing "fastboot>" on the bottom
21. In the command prompt, type "fastboot devices" to see if the device is recognized.
22. Now we are going to flash CWM Recovery: type in command prompt: "fastboot flash recovery CWM_recovery.img"
23. reboot into recovery by typeing into command prompt: " "fastboot reboot" while holding VOL+ on the phone.
24. When the options screen on the phone appears, press VOL- to select the recovery mode. This will boot into CWM recovery.
25. In CWM recovery, select "install ZIP" and select "From Memory card" and select the Open Gapps file we have copied there in step 7a.
26 When flashing is done, type into the command prompt: "adb reboot" to reboot the phone.
This should reboot the phone. first 5 minutes it might be very slow as it is optimizing (Google) apps, but then Google Play store should be working on your phone!
Attention!
When installing SuperSU you can NOT get ROOT!!!
You will receive a cyclic reboot. And for the restoration of the phone need flash original recovery, and then install the firmware version B128 from the official site (update.zip).
Links for firmware version B128:
TWRP recovery
Original Recovery
Official page TIT-AL00
Firmware version C00B128 from the official site and mirror. Size: 1,2 Gb (The Chinese have made a mistake, inside the archive file located in the upgrade "dlaod" - is wrong, the folder should be called dload.)
Firmware version C00B132 from the official site and mirror. Size: 1,2 Gb
Firmware version C00B135 from the official site and mirror. Size: 1,2 Gb
Firmware from the official site installed only from original recovery, so if you have installed CWM recovery, you must first restore the original as it is written above, and already from it to make a clean install.
Can't open the Huawei Unlock tool...
Thanks for the guide but there's a crucial step that seems not to work: the "Huawei Unlocker.zip" tool only contains an adb.exe, fastboot.exe, and a few non-Windows-executable files (busybox and 2 .dll's) so how do we execute this tool?
gordonnorth said:
8. Unzip and open the Unlock tool (you might need to disable the virus checker, as this will be flagged and deleted, at least this was the case with me) --> fill in IMEI 1, get Product ID, write that down
Click to expand...
Click to collapse
=> How to "open the Unlock tool"? It seems to be missing from the .zip file... could you re-upload somehow?
Thanks again!
tomvanbraeckel said:
Thanks for the guide but there's a crucial step that seems not to work: the "Huawei Unlocker.zip" tool only contains an adb.exe, fastboot.exe, and a few non-Windows-executable files (busybox and 2 .dll's) so how do we execute this tool?
=> How to "open the Unlock tool"? It seems to be missing from the .zip file... could you re-upload somehow?
Thanks again!
Click to expand...
Click to collapse
Hi!
I see that I attached the wrong file here. have corrected in the meantime.
Please try the unlocker tool that is attached now.
gordonnorth said:
Hi!
I see that I attached the wrong file here. have corrected in the meantime.
Please try the unlocker tool that is attached now.
Click to expand...
Click to collapse
It worked perfectly now. Google Apps are installed. Thanks a lot, guys!
One more gotcha: the Huawei Unlocker.exe didn't work for me when executed directly from the .zip file, even though it's only one file so I expected that to work... Perhaps it self-extracts... Anyway, you need to unpack the .zip file first and then execute the unlocker .exe
; said:
when I flash the gapps.zip from sdcard.
cwm told me the signature verification faild...
maybe I should try another gapps?
Click to expand...
Click to collapse
; said:
I tried 5 gapps blow but none of them works...
Click to expand...
Click to collapse
Found the problem. and finnaly it works.
The first time of the CWM installation failed. ( but adb told me OK).
so I just flash CWM again to solve the problem.
Many thanks.
so many chinese user also wanna to use gapps, even the Gov. banned google services here.
Hope there's a way to root the device , to delete those useless pre-installed apps.
Thanks again.
different huawei emuı page
hi my friends,
there is a problem about huawei emui page
I check the your advice but When I want to appliacaiton this step, I see different page in web site
and than I can not submit this step I don't take unlock code.
what is the problem pls help me !!
thanks
petere15 said:
hi my friends,
there is a problem about huawei emui page
I check the your advice but When I want to appliacaiton this step, I see different page in web site
and than I can not submit this step I don't take unlock code.
what is the problem pls help me !!
thanks
Click to expand...
Click to collapse
Hi petere15,
did you go to this website? it still seems fine to me?
https://emui.huawei.com/en/plugin.php?id=unlock&mod=detail
The same model TIT-AL00 announced to India with the name of Honor Holly 2 Plus.
Review
This means that you can install the firmware, which has services Googe.
andrik22 said:
The same model TIT-AL00 announced to India with the name of Honor Holly 2 Plus.
Review
This means that you can install the firmware, which has services Googe.
Click to expand...
Click to collapse
Hey Andrik,
do you know where we can download that firmware?
and did you test that already? might be good to have a more westernized ROM available, so also the EMUI badges might work for whatsapp for example...
gordonnorth said:
Hey Andrik,
do you know where we can download that firmware?
and did you test that already? might be good to have a more westernized ROM available, so also the EMUI badges might work for whatsapp for example...
Click to expand...
Click to collapse
Today just announced!
On sale from 15 February. I think the firmware will be closer to the date of sale.
Firmware appear on this page.
The same phone will be sold in Europe, called Huawei Y6 Pro.
http://www.notebookcheck.com/Huawei...er-unteren-Mittelklasse-geleakt.156905.0.html
http://www.allmobilearea.com/huawei-y6-pro/
User guide in English and Mirror.
hi,
im not expert for phones so i need little help. Problem begine on geting unlock key.
My Huawei page look diferent , don't have product type.
Cant paste link coz im new here: h t t p://imgur.com/nGkL3R1.
Any idea what to do next?
in product model i try to write" huawei tit-al00", only "tit-al 00" and i get the same message.
Sorry on my bad english, hope someone will understand my problem.
thx
GONF said:
hi,
im not expert for phones so i need little help. Problem begine on geting unlock key.
My Huawei page look diferent , don't have product type.
Cant paste link coz im new here: h t t p://imgur.com/nGkL3R1.
Any idea what to do next?
in product model i try to write" huawei tit-al00", only "tit-al 00" and i get the same message.
Sorry on my bad english, hope someone will understand my problem.
thx
Click to expand...
Click to collapse
Manufacturer again changed the method of obtaining the unlock code.
You need to go to the phone account Huawei. For example, Huawei club, HiApp or Huawei Cloud+.
The report said that you did not go to these applications for more than 14 days.
The second option - for unlock to write their e-mail data (down - contact us).
thx for answering, first solution didnt work, so i sent mail, hope i will get some positive answer.
Hmm, still no answer from huawei tehnical support.
Anyone have some expirience with them?
Or, is ther any other solution for my problem?
pls anyone.... girl will cut my ..... if i don fix her mobile
GONF said:
Hmm, still no answer from huawei tehnical support.
Anyone have some expirience with them?
Or, is ther any other solution for my problem?
pls anyone.... girl will cut my ..... if i don fix her mobile
Click to expand...
Click to collapse
Unfortunately, there is only a version of the installation software VPN, included in the service with Huawei phone with the expectation of 14 days.
I have not tested it should work in theory.
Perhaps you can write in support of Huawei in your country - that they may request an unlock code from colleagues in China.
Hi, I still have not solved my problem, so I have one question.
Will it be possible in the near future root this device?
Or i can trow it in the trash.
GONF said:
Hi, I still have not solved my problem, so I have one question.
Will it be possible in the near future root this device?
Or i can trow it in the trash.
Click to expand...
Click to collapse
Even if it will be able to get root, too, need to unlock the bootloader on it.
You have tried to write an e-mail?
Send an email to [email protected] Email them the following. They usually email you back and tell you to do go online to unlock your bootloader and it should work on the website, or never email you back:
Hello. I keep getting an error when trying to unlock my phone on the unlock page.
Model: TIT-AL00 (Or whatever model you have)
Serial: Put in your phones serial number here. (You get this in About phone, Status)
IMEI: Put in your phones IMEI number here. (You get this in About phone, Status, it's IMEI1)
Product ID: (Go into your phone dialer and dial *#*#1357946#*#* and it will give you your Product ID, or use Huawei Unlocker)
Good night guys, and happy new year.
Yesterday (December 31), the GSM network of my X2 blocked out of nowhere, and now, is asking for the NCK code to release the network. Also when I go to check the IMEI number, it appears only zeros. I researched the internet on how to get the NCK, but I did not find the methods of deblocking reliable. Has anyone had this problem? Does anyone know any way to solve this? Strange to say, since I've been with the device for almost 3 years and it has never happened before. And to make matters worse, some apps are no longer working, like google play, gmail ...
Thank you very much in advance,
I have the same problem
I put my SIM Card into another phone and it works without any problems, so it guess it's a problem on the X2 side.
I did a factory reset, formating the internal card, reinstall the system and restore a backup, none of them helped
I tried to do the same, and it did not work, either.
Do you use Magisk? If you do so, it's known for being the culprit.
Yes, I installed the newest version of Magisk.
I deinstalled the app without any success to solve the problem and then I reseted the phone several times also without solving the problem.
Does anybody has a clue where this information is stored???
Thanks in advance
Wolfgang
woschirmer said:
Yes, I installed the newest version of Magisk.
I deinstalled the app without any success to solve the problem and then I reseted the phone several times also without solving the problem.
Does anybody has a clue where this information is stored???
Thanks in advance
Wolfgang
Click to expand...
Click to collapse
Uninstalling the app won't do anything because Magisk modifies your kernel (boot.img) which you must restore to the original one from a TWRP Backup or use the Magisk uninnstaller.zip.
erayrafet said:
Uninstalling the app won't do anything because Magisk modifies your kernel (boot.img) which you must restore to the original one from a TWRP Backup or use the Magisk uninnstaller.zip.
Click to expand...
Click to collapse
I tried this several times, but it didn't work
I'll see what I can do - thank you!
I got the same situation
1. unlock phone........ok
2. TWRP.................................ok
3. ROOT SuperSU.....................stay in flower LOGO too long. So I POWER OFF
4. Change to ROOT Magisk15.2.zip I got the same situation as you
Now. I think that we lost EFS
SO.We need someone backup EFS with TWRP
and share the backup files to us
We can try restore EFS with TWRP. And bless someting good happen
Germano1980 said:
Good night guys, and happy new year.
Yesterday (December 31), the GSM network of my X2 blocked out of nowhere, and now, is asking for the NCK code to release the network. Also when I go to check the IMEI number, it appears only zeros. I researched the internet on how to get the NCK, but I did not find the methods of deblocking reliable. Has anyone had this problem? Does anyone know any way to solve this? Strange to say, since I've been with the device for almost 3 years and it has never happened before. And to make matters worse, some apps are no longer working, like google play, gmail ...
Thank you very much in advance,
Click to expand...
Click to collapse
ForeverYangGo said:
I got the same situation
1. unlock phone........ok
2. TWRP.................................ok
3. ROOT SuperSU.....................stay in flower LOGO too long. So I POWER OFF
4. Change to ROOT Magisk15.2.zip I got the same situation as you
Now. I think that we lost EFS
SO.We need someone backup EFS with TWRP
and share the backup files to us
We can try restore EFS with TWRP. And bless someting good happen
Click to expand...
Click to collapse
You just need to restore your stock boot.img. There's no EFS partition here because this isn't a device with a Qualcomm chip.
For root you can use SuperSU 2.82-SR5 + suhide.
erayrafet said:
You just need to restore your stock boot.img. There's no EFS partition here because this isn't a device with a Qualcomm chip.
For root you can use SuperSU 2.82-SR5 + suhide.
Click to expand...
Click to collapse
could anybody upload a clean boot.img? I tried to restore the boot image from my custom release (AJ Kangvip V3), but it didn't help.
I need help
Hi friend
I restore stock recovery and got stock rom and copy dload floder to SD card
Then press power, vol+,vol- 3 keys at same time
But The New system stay in some situation
Could you tell me how to restore my stock boot.img
I try to get boot.img file form UPDATE.APP
Then run fastboot flash boot boot.img
But nothing to happen?
Could you tell me more?
erayrafet said:
You just need to restore your stock boot.img. There's no EFS partition here because this isn't a device with a Qualcomm chip.
For root you can use SuperSU 2.82-SR5 + suhide.
Click to expand...
Click to collapse
ForeverYangGo said:
Hi friend
I restore stock recovery and got stock rom and copy dload floder to SD card
Then press power, vol+,vol- 3 keys at same time
But The New system stay in some situation
Could you tell me how to restore my stock boot.img
I try to get boot.img file form UPDATE.APP
Then run fastboot flash boot boot.img
But nothing to happen?
Could you tell me more?
Click to expand...
Click to collapse
Yeah, it should be good. Maybe you should install your firmware with Stock recovery and dload method. Then a factory reset shoud fix the problem but don't flash Magisk.
How to install firmware with Stock recovery ?
whick files belong to "firmware" and how to do?
I need step by step teaching :crying:
---------- Post added at 01:01 PM ---------- Previous post was at 12:36 PM ----------
Hi friend
I copy dload floder to SD card，Then press power, vol+,vol- 3 keys at the same time
I think this way incloud boot.img ,firmware and all needs for phone system
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
erayrafet said:
Yeah, it should be good. Maybe you should install your firmware with Stock recovery and dload method. Then a factory reset shoud fix the problem but don't flash Magisk.
Click to expand...
Click to collapse
ForeverYangGo said:
How to install firmware with Stock recovery ?
whick files belong to "firmware" and how to do?
I need step by step teaching :crying:
---------- Post added at 01:01 PM ---------- Previous post was at 12:36 PM ----------
Hi friend
I copy dload floder to SD card，Then press power, vol+,vol- 3 keys at the same time
I think this way incloud boot.img ,firmware and all needs for phone system
Click to expand...
Click to collapse
1.Extract recovery.img from UPDATE.APP with HuaweI Extractor.
2.Open your Settings app, go to the About tablet section and tap on Build number 7 times. Go back, open Developer options and enable USB debugging.
3.Connect your tablet to your PC and open a command prompt in the platform tools folder.
4. Type:
adb reboot bootloader
Wait a second. Now type:
fastboot flash recovery
and drag the extracted recovery.img file, then hit enter.
5.Type:
fastboot reboot
6.Open Project menu with *#*#2846579#*#*
7.Select Software Upgrade, tuen SDCard Upgrade and Ok. Make sure that you have the UPDATE.APP file in the dload folder on your SD card.
I Extract recovery.img and recovery2.img from UPDATE.APP with HuaweI Extractor
So Just take recovery.img right?
erayrafet said:
1.Extract recovery.img from UPDATE.APP with HuaweI Extractor.
2.Open your Settings app, go to the About tablet section and tap on Build number 7 times. Go back, open Developer options and enable USB debugging.
3.Connect your tablet to your PC and open a command prompt in the platform tools folder.
4. Type:
adb reboot bootloader
Wait a second. Now type:
fastboot flash recovery
and drag the extracted recovery.img file, then hit enter.
5.Type:
fastboot reboot
6.Open Project menu with *#*#2846579#*#*
7.Select Software Upgrade, tuen SDCard Upgrade and Ok. Make sure that you have the UPDATE.APP file in the dload folder on your SD card.
Click to expand...
Click to collapse
ForeverYangGo said:
I Extract recovery.img and recovery2.img from UPDATE.APP with HuaweI Extractor
So Just take recovery.img right?
Click to expand...
Click to collapse
Yes
Dear
I understand the process you say
But I don't know what's different with my doing
First I turn off phone ......presss power + Vol down ...enter fastboot mode
Then I flash stock recovery.img which Extract from UPDATE.APP (download from TW wesite)
REBOOT to system
Then I copy dload floder to SD card
connect PC and phone with USB(I know how to set developmenter and USE debug before this )
I turn off phone and press 3 keys at same time, System will restore to new one
But either the way you say or my doing went to the same result
the SIM network NCR need unlock
ForeverYangGo said:
I Extract recovery.img and recovery2.img from UPDATE.APP with HuaweI Extractor
So Just take recovery.img right?
Click to expand...
Click to collapse
ForeverYangGo said:
Dear
I understand the process you say
But I don't know what's different with my doing
First I turn off phone ......presss power + Vol down ...enter fastboot mode
Then I flash stock recovery.img which Extract from UPDATE.APP (download from TW wesite)
REBOOT to system
Then I copy dload floder to SD card
connect PC and phone with USB(I know how to set developmenter and USE debug before this )
I turn off phone and press 3 keys at same time, System will restore to new one
But either the way you say or my doing went to the same result
the SIM network NCR need unlock
Click to expand...
Click to collapse
I saw that you have a GEM-702L with parts from GEM-701L firmware which might also be the issue. You must use a firmware made for you hardware variant or debrand to GEM-701L firmware which requires you to do some extra steps. Check your build number and post a screenshot.
Dear
I find the situaction. So I post a screenshot
But I really don't know why to happen
Could you tell me where to show the build number
because My fhone is not English System
---------- Post added at 07:35 AM ---------- Previous post was at 07:23 AM ----------
*#*#1357946#*#* will show Product ID (8 numbers)
But after unlock phone I found *#*#1357946#*#* will show nothing
erayrafet said:
I saw that you have a GEM-702L with parts from GEM-701L firmware which might also be the issue. You must use a firmware made for you hardware variant or debrand to GEM-701L firmware which requires you to do some extra steps. Check your build number and post a screenshot.
Click to expand...
Click to collapse
ForeverYangGo said:
Dear
I find the situaction. So I post a screenshot
But I really don't know why to happen
Could you tell me where to show the build number
because My fhone is not English System
---------- Post added at 07:35 AM ---------- Previous post was at 07:23 AM ----------
*#*#1357946#*#* will show Product ID (8 numbers)
But after unlock phone I found *#*#1357946#*#* will show nothing
Click to expand...
Click to collapse
It's at the top on this page.
Hi
in this thread i will show you how to do each of this:
POCO X3 PRO{vayu}
1.TWRP+ROOT
2.RSA DISABLE
3.DIAG MODE
4.EFS RESET
5.IMEI REPAIR
without Any Box.
----------
***********You Will Do it By Your Responsibility and I'm not Responsible for any damage to your Device,Read Thread Carefully and then Do it and try not to mess your device*********
--------
Requirements:
-Iphone 6 Board for its Resistor
-Xiaomi Imei Tool Link
-Qpst Link
-Twrp + EFS Reset Tool Link
-Magisk 23 zip file Link
-Magisk Manager APP Link
-Stock Firmware Link
-Eng Firmware LINK >>>>File Password is : iaasteam.com<<<<<<
--------
I Did All of this Steps and Job Done this Means Its Tested dont Blame me For Any Damage to Your Device
Do it Just if you know What you Do
Not for Newbies
---------------
Some Poco X3 Pro Devices Bootloop After EFS Reset:
it can caused Becuase of Firmware Security or RSA Encryption of Device Imei:
We Have Two Method For this:
1.Flash ENG Rom Then Continue The Steps 1 to 4 and no need root(Because ENG rom have root access already)
2.Do entire Steps on stock Firmware then if it gives error try method 1
But if Not if this methods Work Problem is with the Step 1.RSA DISABLE and you should Check You Resistor
---------------
1.RSA DISABLE
You Should Disable RSA of the Phone To Write Imei on it.
For this
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Remove this resistor and Change it with Picture 2 from Iphone 6 Board 50k resistor
for better Performance of work you can Measure its kohm by ohm meter it should be 45 to 50k by ohm meter
replace the resistor in picture one with this
------------
First Time We do entire of Job on stock Firmware if firmware security Prevent us to do our work then we flash the phone with eng firmware,and eng firmware no need root just need flash twrp
-----------
2.TWRP + ROOT
Download Reqirment TWRP + EFS RESET TOOL
Reboot phone in fastboot and connect it to pc
run .bat file and press key 1
twrp will be flashed
Wipe/factory reset Phone by twrp if storage not shown for installing packages reboot agian to twrp
Download Magisk zip and Apk from reqirement
****Go to Backup Section of TWRP>Check EFS Partition>Back it up and Copy it to PC for Avoid Baseband null***** And then Continue the other Steps
Connect Phone to pc
Copy Magisk23.zip to phone storage and install it by twrp
Reboot phone to system
and install Magisk Manager
Now phone Should Be Rooted.
Each time you reboot your phone from Recovery to system,TWRP recovery will be deleted onm your phone
when you see your phone rooted
----------
3.DiagPort & QCN Backup & Modify
Download QPST in reqirement
Xiaomi Imei Tool in reqirement
Install Xiaomi Imei Tool
View attachment 5515295
Connect phone to pc in normal Mode
Enable USB Debugging and Select File Transfer mode on phone
Click Open Diag Port now your diag prot enabled
***** Do not use Xiaomi Imei tool QPST******
Install QPST from Reqirements Section
Run QPST Configuration(you can search in start menu for it Because it dont have shortcut in desktop)
QPST Configuration Detect Your phone in diag mode then
Click on Start Clinets>Software Download>Backup
Backup QCN And Xqcn Both(QCN is enough but I suggest you to backup both of them)
when you backed up Qcn
Open Xiaomi Imei Tool
And run QCN Editor
View attachment 5515301
1.select Qcn file you Backed Up
2.Select Registration Method on 2Sim Like in picture
3.Write Imei 1 and imei 2
4.Click Create Button and Save our Modified QCN.
--------------------
4.EFS Reset And Modified QCN Restore(Imei Repair)
Warning:You should Backed up your EFS By TWRP in STEP 2 and Copied it in PC And Then Come To This Step
Reboot your Phone to Fastboot
-Open TWRP+EFS reset .bat file you downloaded in step 2
-press 1 and wait untill phone reboots to twrp recovery
-in the .Bat File Menu press key 2 when phone already is in twrp menu
-Reboot Phone to system Again Now Efs Reseted and Phone Dont Have IMEI
*******If You Dont Replaced Correct Resistor in Step 1 then your phone should give you NV Data Corrupted Error in this Step or Phone Restarts Each Time********
-When Phone Comes Up Enable Diag port Again and run QPST
Run QPST Configuration(you can search in start menu for it Because it dont have shortcut in desktop)
QPST Configuration Detect Your phone in diag mode then
Click on Start Clinets>Software Download>Restore
Select Modified Qcn that you Created By Xiaomi Imei Tool in Step 3 and Push Start.
Wait Untill Progress Done And Phone Reboots.
Now You Should Have Poco X3 pro Dual Imei Repaired.
If you Get Any Error Just Read Troubleshooting Section
--------------------------------
*****************Troubleshooting****************
1-After EFS Reset Phone Restarts and dont Work Correct
A:it can caused by two problem: 1- firmware security 2-Resistor Change Problem
For Firmware Security:
-Download ENG Firmware From Requirement section and Flash it by fastboot
-then Reboot To Fastboot again Flash Twrp recovery and do not try to root ENG firmware(Because it have Root Access by default)
-In Twrp Reset EFS Again In Step 4
-Reboot to ENG firmware and Enable Diag Port and Write Modified Qcn
-Flash Global Stock Firmware i have linked to requirement no diffrence at all you can flash any version of global firmware
***If Again Problem Not fixed It's your 50k Resistor Changing Problem and you should check it***
2-When I Enable Diag Port QPST Can not find my phone
A:Just Check You Drivers And Device Manager
--------------------------------
*****In Some Websites Says You Need ENG QCN for imei repair,No need of ENG QCN Just Modify Phones Original QCN******
--------------------------------
Files Uploaded To mega.nz and Links Stays Alive forever.
--------------------------------
Push Thanks Button,Like if this Guide fixed your problem
If you have a question, feel free to ask and I will answer as soon as possible
***********You Will Do it By Your Responsibility and I'm not Responsible for any damage to your Device,Read Thread Carefully and then Do it and try not to mess your device*********
I have a question, if I have a Poco X3 Pro with a blank imei and an unknown baseband, I don't have the EFS backup or the box where the imei comes from, changing the resistance and following the step-by-step guide could I recover the imei?
felixpaz1992 said:
I have a question, if I have a Poco X3 Pro with a blank imei and an unknown baseband, I don't have the EFS backup or the box where the imei comes from, changing the resistance and following the step-by-step guide could I recover the imei?
Click to expand...
Click to collapse
if problem not with the hardware
yes of course you can fix it
when you remove resistance and disable rsa
and write its original imei on it.
Any change in the imei ID of the device is illegal in most countries, please respect the law.and Also respect XDA Law about it.
I've reverted the OP and thread title as they were, as well as unlocking it, and will PM all appropriate users.
Thank you.
roirraW edor ehT said:
I've reverted the OP and thread title as they were, as well as unlocking it, and will PM all appropriate users.
Thank you.
Click to expand...
Click to collapse
Thank you, I took the time to write this
Thank you for your positive management
After removing the resistor can it be re-installed?
Jssdje said:
After removing the resistor can it be re-installed?
Click to expand...
Click to collapse
no then rsa enabled again
Non of one of your attachment are available please update the pictures of resistor pic
Thanks
mosirezaei said:
Non of one of your attachment are available please update the pictures of resistor pic
Thanks
Click to expand...
Click to collapse
Hi thank you for report i have uploaded them but now the attachments deleted
wait untill tomorrow i will fix it
dashti.95 said:
Hi thank you for report i have uploaded them but now the attachments deleted
wait untill tomorrow i will fix it
Click to expand...
Click to collapse
Hello
I still waiting for the attachment photos of resistors
if you can send it to my email will be great
[email protected],com
thanks bro
backup efs eng firmware mode .backup was saved fsc,fsg,modemst1 and modemst2. after reset efs baseband unknown. flash backup partition in fastboot mode. still baseband unknown.
problem solved by write qcn.
alak said:
backup efs eng firmware mode .backup was saved fsc,fsg,modemst1 and modemst2. after reset efs baseband unknown. flash backup partition in fastboot mode. still baseband unknown.
problem solved by write qcn.
Click to expand...
Click to collapse
Can you give me the qcn please....
Mail : [email protected]
kallumama said:
Can you give me the qcn please....
Mail : [email protected]
Click to expand...
Click to collapse
tomorrow i will send you
I repair 2nd Imei of Poco X3 pro Vayu from UMT RSA method in eng Rom. I get backup of QCN. it shows imei1 0 imei2 (86*************12) but when I flash global rom. it shows NV data corrupt. I again flash ENG rom. write that backup QCN it shows Original IMEI's but when I flashed Global Rom It shows nv data error again. although Original imei of that Phone. I erase efs from Fastboot that also doesn't help me. what is the problem & how to solve it.
can I flash custom rom for mobile work normally without sim?
or custom rom doesn't help?
if any firmware that solve my problem & phone work normally (without sim) kindly tell me.
saqibsm said:
I repair 2nd Imei of Poco X3 pro Vayu from UMT RSA method in eng Rom. I get backup of QCN. it shows imei1 0 imei2 (86*************12) but when I flash global rom. it shows NV data corrupt. I again flash ENG rom. write that backup QCN it shows Original IMEI's but when I flashed Global Rom It shows nv data error again. although Original imei of that Phone. I erase efs from Fastboot that also doesn't help me. what is the problem & how to solve it.
can I flash custom rom for mobile work normally without sim?
or custom rom doesn't help?
if any firmware that solve my problem & phone work normally (without sim) kindly tell me.
Click to expand...
Click to collapse
1.What Flasher you using to flash data?
2.give me a list of files in your firmware directory please list it for me.
I need to know because:
In qualcomm series of xiaomi phones you have a file named *NON-HLOS*
You should use NON-HLOS file from eng Rom not the original file from global rom.(NON-HLOS file is eng modem file)
give me info i will help you
dashti.95 said:
1.What Flasher you using to flash data?
2.give me a list of files in your firmware directory please list it for me.
I need to know because:
In qualcomm series of xiaomi phones you have a file named *NON-HLOS*
You should use NON-HLOS file from eng Rom not the original file from global rom.(NON-HLOS file is eng modem file)
give me info i will help you
Click to expand...
Click to collapse
I have a doubt in which directory of the ENG Rom I find the NON-HLOS file and if I can back it up, I "install" it in the global Rom, would the QCN written when it was in the ENG Rom work?
dashti.95 said:
1.What Flasher you using to flash data?
2.give me a list of files in your firmware directory please list it for me.
I need to know because:
In qualcomm series of xiaomi phones you have a file named *NON-HLOS*
You should use NON-HLOS file from eng Rom not the original file from global rom.(NON-HLOS file is eng modem file)
give me info i will help you
Click to expand...
Click to collapse
I have followed the guide, I was able to recover the original imei that came in the box, I have changed the 50ohm resistor, when I go back to stock rom I have baseband, I have both imei, but I have no signal, if I want to call a message appears saying "deactivate the airplane mode to call"
felixpaz1992 said:
I have followed the guide, I was able to recover the original imei that came in the box, I have changed the 50ohm resistor, when I go back to stock rom I have baseband, I have both imei, but I have no signal, if I want to call a message appears saying "deactivate the airplane mode to call"
Click to expand...
Click to collapse
Its because of qcn you used its not compatible with your device.
dashti.95 said:
Its because of qcn you used its not compatible with your device.
Click to expand...
Click to collapse
I used the published QCN ENG and edited it with the imei that I found in the original box of the equipment, now both imei appear in the global Rom but I have the ghost plane mode, absolutely everything works except the mobile radio
felixpaz1992 said:
I have followed the guide, I was able to recover the original imei that came in the box, I have changed the 50ohm resistor, when I go back to stock rom I have baseband, I have both imei, but I have no signal, if I want to call a message appears saying "deactivate the airplane mode to call"
Click to expand...
Click to collapse
two questions:
1.Which NON-HLOS you used?Stock or Eng?
2.What type of Qcn you used?.xqcn or .qcn?