Hi,i'm a new member who use shw-m180l.
my tablet had really bad memory(444mb) so could't run any apps properly.
so I was about to install jellybean rom with odin.
I installed the usb driver about twice.
I run the odin and I open the file JB_SHW-M180L_Release_2.tar that made from some korean user.That custom rom was tested.
But I didn't know that I must check the usb tethering to install the android firmware.
So of course I got fail message from odin.
After that, My tablet had error "update not completed!".
this screenshot is from other blogger, but the error is probably same.
I tried samsung kies but my pc can't recognize tablet.
*the tablet can boot when I recharge. But it had that error again and again.
Please answer to fix this error!!
Related
Hello! I have a huge problem with my tf700t, Windows 8 won't recognise my device. In device manger it just says: Unknown device.
I'v tried to install the usb drivers manualy but it won't work... I just get "can not find driver software for this device" the error device mangere gives me is "Windows has stopped this device because it has reported problems. (Code 43)" I also tired to install asus sync....
I'm running newest frimware form asus (4.2.1)
Before i installet the 4.2.1 from asus I was running offical cm 10.1 and everything was working. Then i decided to go back stock because i was going to sell the device. I wiped everything including system to unroot the device. After that I downloaded the firmware for asus web page and flashed it. Everything was working except i couldn't connect it to a computer. So i decided to try to flash a older frimware (4.1.1) but I was not able to get into recovery.
I don't know what to do now. I can't install a new rom becouse i can't connect it to my computer or get ot the recovery. I can also not install a new recovery because i don't have root or adb and fastboot won't work.
Any ideas ?
TheGprodz said:
Hello! I have a huge problem with my tf700t, Windows 8 won't recognise my device. In device manger it just says: Unknown device.
I'v tried to install the usb drivers manualy but it won't work... I just get "can not find driver software for this device" the error device mangere gives me is "Windows has stopped this device because it has reported problems. (Code 43)" I also tired to install asus sync....
I'm running newest frimware form asus (4.2.1)
Before i installet the 4.2.1 from asus I was running offical cm 10.1 and everything was working. Then i decided to go back stock because i was going to sell the device. I wiped everything including system to unroot the device. After that I downloaded the firmware for asus web page and flashed it. Everything was working except i couldn't connect it to a computer. So i decided to try to flash a older frimware (4.1.1) but I was not able to get into recovery.
I don't know what to do now. I can't install a new rom becouse i can't connect it to my computer or get ot the recovery. I can also not install a new recovery because i don't have root or adb and fastboot won't work.
Any ideas ?
Click to expand...
Click to collapse
You do have USB debugging enabled??
What happens if you boot with Power and Volume Down, then select the flashing RCK icon with Volume Up? No recovery???
no....
Yes USB debugng is checked, and i'm not able to get to the recovery while pressing Power and Volume Down, then select the RCK icon....
See the picture of what happen when i choose RCK
TheGprodz said:
Yes USB debugng is checked, and i'm not able to get to the recovery while pressing Power and Volume Down, then select the RCK icon....
See the picture of what happen when i choose RCK
Click to expand...
Click to collapse
What you see there IS the stock recovery which overwrote CWM or TWRP when you flashed the stock firmware.
You can use the stock recovery only for one thing: Flashing an official Asus update. The Droid on his back tells you that the stock recovery does not find an update.
So that part is good. You're rom is intact and healthy.
Do you have access to a different computer? Can you try to get the tablet to connect in Windows 7?
I have no experience with Win8 - no idea what the driver problem may be. But that's what it is: You need to find he correct drivers....
I tried with my mothers laptop but that's also running windows 8 but same problem apres, and the other pc I have runs ubuntu :/
TheGprodz said:
I tried with my mothers laptop but that's also running windows 8 but same problem apres, and the other pc I have runs ubuntu :/
Click to expand...
Click to collapse
Check out this thread: http://forum.xda-developers.com/showthread.php?t=1583801
I'm not able to install drivers.... this is the error message translated from Norwegian to English
Can not install unknown device!
can not find driver software for device
If you know the name of the manufacturer of your device, please visit the manufacturer's website and look for driver software in the support section.
This is the error i get when i locate it to the drivers that i downloaded. I haved tried manny different drivers.
bump
Hi everyone,
I have currently some big issue with my GT-N8010.
My custom rom wasn't running very well so I decided to reset my tablet and go back to a new fresh installation.
I downloaded the latest firmware of the tablet on sammobile and started to update it with Odin PC, but in the middle of the transfert I got an error and now my tablet is stuck on the "Firmware upgrade encoutered an issue. Please select recovery mode in Kies & try again.".
I have no idea how to fix it! And I can't go back to download mode anymore. On top of that, my tablet seems not to be recognize by my computer (I tried to install Kies and the samsung usb driver several times but it keeps saying that's the driver is not ok)...
Can someone help me please ?
Thank you in advance!
What custom rom did you had ? 4.4.2 or 4.1.2 ?
KoRoZIV said:
What custom rom did you had ? 4.4.2 or 4.1.2 ?
Click to expand...
Click to collapse
It was a 4.1.2 (HD Revolution) and I tried to flash with odin the N8010XXUCMK2_N8010XSACNA2_XSA
First uninstall kies and all usb drivers. Restart your computer.
If you can get in download mode (power+volume down then volume up when asked) :
Install some drivers from the sticky topics here on xda. Download the firmware again from another location if possible. Use a different usb port.
If you can't get in download mode, you have to try with kies. I never had success whit it, and i really need it. But it says that n8010 does not support initializing or something like that. Maybe someone else can help with kies.
Sent from my GT-N8010 using Tapatalk
I don't know where it comes from...
I tried everything, uninstall/reinstall Kies/Usb driver, put a VM with Win7 (As I am under Windows 8.1), put Win7 in dual boot to maybe fix the compatibility issue but nothing seems to work! And of course I don't have any other computer to use...
That's maybe the reason the tablet get broken as I used to use Odin on another PC and I didn't check if the usb driver was installed on this one??
I just know that Odin recognized my tablet so I was able to launch the installation of the new firmware.
I feel really bad...Hope the tablet is not definitly dead!
Faulty USB cable perhaps ?
Sent from my GT-N8010 using Tapatalk
Ok so I went to a Samsung store and they told me that I have to send my tablet to the repair center in the country where I bought the device.
It's a big issue for me as I am now living in Australia and my tablet has been bought in France.
On top of that the guy from Samsung explained me that now it's normal if my tablet is not any longer recognize by my computer...
I heard about JTAG, I don't have any idea about the subject but may it fix my problem?
Does someone know how samsung is able to fix the tablet, so I may fix it myself instead of sending to them...?
Hi,
Figured id start off by explaining the history on my Samsung Note N8010
A while back i installed Hyperdrive Rom RS8 (i think), no problems, flawless. However it did change my device id to an N8013, not sure why.
Recently i wanted to use SkyGo Tablet app, however root cloak and Voodoo does not cloak SkyGo Tablet app on this specific rom so i figured id revert back to the original 4.1.2 stock.
I used Mobile Odin, grabbed the zip/tar from the Sam-mobile and hit go.
On reboot, it would not load in, stuck on the Samsung Note 10.1 splash. I do have access to download mode and recovery mode, but it's labelled Android System Reocvery <3e>.
It is worth noting that USB debug did not work on Hyperdrive, so currently no matter what computer i connect this tablet to Odin, Kies or anything will not see it.
When trying to "apply update from sd card" i get E:\ mount problems, it pretty much fails every time.
Any suggestions?
kitchenspoon said:
Hi,
Figured id start off by explaining the history on my Samsung Note N8010
A while back i installed Hyperdrive Rom RS8 (i think), no problems, flawless. However it did change my device id to an N8013, not sure why.
Recently i wanted to use SkyGo Tablet app, however root cloak and Voodoo does not cloak SkyGo Tablet app on this specific rom so i figured id revert back to the original 4.1.2 stock.
I used Mobile Odin, grabbed the zip/tar from the Sam-mobile and hit go.
On reboot, it would not load in, stuck on the Samsung Note 10.1 splash. I do have access to download mode and recovery mode, but it's labelled Android System Reocvery <3e>.
It is worth noting that USB debug did not work on Hyperdrive, so currently no matter what computer i connect this tablet to Odin, Kies or anything will not see it.
When trying to "apply update from sd card" i get E:\ mount problems, it pretty much fails every time.
Any suggestions?
Click to expand...
Click to collapse
The original issue is probably one of two things. If you downloaded the rom directly to your device its Likely a bad download. DID YOU CHECK MD5 Before flashing. There are also limitations to Mobile odin.
What i would suggest is to uninstall Kies . Make sure you have no other android devices installed on your computer .Download the older version again from Samsung website. Install on your computer. Download odin again i think you want the one a version back as well NOT Latest.
Reboot into download mode. Run odin. if it still does not see your device check Device manager and see if its showing up with a yellow mark. Look for a post i made last week explaining how to correct usb driver for windows.. Download mode should work with out usb debug on if i remember correctly..
erica_renee said:
The original issue is probably one of two things. If you downloaded the rom directly to your device its Likely a bad download. DID YOU CHECK MD5 Before flashing. There are also limitations to Mobile odin.
What i would suggest is to uninstall Kies . Make sure you have no other android devices installed on your computer .Download the older version again from Samsung website. Install on your computer. Download odin again i think you want the one a version back as well NOT Latest.
Reboot into download mode. Run odin. if it still does not see your device check Device manager and see if its showing up with a yellow mark. Look for a post i made last week explaining how to correct usb driver for windows.. Download mode should work with out usb debug on if i remember correctly..
Click to expand...
Click to collapse
Hi, cheers for the response,
I have tried all of what you have said but unfortunately no PC will see my device, not even an "unrecognized device". I have access to android system reocvery <e3> and Download mode (Odin) but the pc just won't recognized, tried new leads and so forth, nothing.
Hello everyone,
so my phone is soft-bricked after failure attempt to flash combination files in order to fix the csc.
I follow this thread, but the problem actually has nothing with that.
I used the latest patched odin V3.13.1, with a combination file named COMBINATION_FAC_FA80_G965USQU3ARG2.tar, and the proccess failed at flashing the system, and now i'm stuck; unable to flash other firmwares.
Before that, the phone was working perfectly after I've flashed a G965U1 firmware on it, in order to get rid of the bloatware of the original branded G965U (I don't live in the US).
Also, it successfully OTA updated to the latest G965U1UEU3ARK5 Firmware just a few days ago.
Things that I've tried so far with no success:
*Used different usb ports, both usb 2 and usb 3; and different cables
*Using both an Intel-based PC, and an AMD-based. (I know it may sound unrelated, but thats actually what prevented me from flashing the G965U1 fmwr the first time I tried, because i was using and AMD PC)
*Reinstalling Drives, installing latest kies, installing latest samsung smart switch
*using older versions of Odin
*tried to install the original Sprint firmware (v2) G965USQS2ARF4 through odin
*tried to install the G965U1UEU3ARK5 firmware through odin
The phone is stuck in download mode. sometimes if I disconnect and reconnect it, I get an unrecognized usb device message. so I need to reboot the phone again to download mode so the pc will recognize it.
and the result is always a failure:
either due to rev check, with the original OEM firmware
during the installation at 'vendor'/'system' step, due to auth error, when trying the G965USQU3ARG2 Combination file or the G965U1UEU3ARK5 files with patched odin
or even before that step with older versions of odin.
I'm out of ideas... I hope someone here has the knowledge to help in some way, Please...
Amsiman said:
Hello everyone,
so my phone is soft-bricked after failure attempt to flash combination files in order to fix the csc.
I follow this thread, but the problem actually has nothing with that.
I used the latest patched odin V3.13.1, with a combination file named COMBINATION_FAC_FA80_G965USQU3ARG2.tar, and the proccess failed at flashing the system, and now i'm stuck; unable to flash other firmwares.
Before that, the phone was working perfectly after I've flashed a G965U1 firmware on it, in order to get rid of the bloatware of the original branded G965U (I don't live in the US).
Also, it successfully OTA updated to the latest G965U1UEU3ARK5 Firmware just a few days ago.
Things that I've tried so far with no success:
*Used different usb ports, both usb 2 and usb 3; and different cables
*Using both an Intel-based PC, and an AMD-based. (I know it may sound unrelated, but thats actually what prevented me from flashing the G965U1 fmwr the first time I tried, because i was using and AMD PC)
*Reinstalling Drives, installing latest kies, installing latest samsung smart switch
*using older versions of Odin
*tried to install the original Sprint firmware (v2) G965USQS2ARF4 through odin
*tried to install the G965U1UEU3ARK5 firmware through odin
The phone is stuck in download mode. sometimes if I disconnect and reconnect it, I get an unrecognized usb device message. so I need to reboot the phone again to download mode so the pc will recognize it.
and the result is always a failure:
either due to rev check, with the original OEM firmware
during the installation at 'vendor'/'system' step, due to auth error, when trying the G965USQU3ARG2 Combination file or the G965U1UEU3ARK5 files with patched odin
or even before that step with older versions of odin.
I'm out of ideas... I hope someone here has the knowledge to help in some way, Please...
Click to expand...
Click to collapse
Guys at imeigurus has a service. Check on them. Those guys have access to special Samsung firmware that they can manipulate Samsung's as they like. They do what others can't, they can support you remotely using teamviewer. But snap the download pic here let me see
show me your device in download mode
leonardojt said:
Guys at imeigurus has a service. Check on them. Those guys have access to special Samsung firmware that they can manipulate Samsung's as they like. They do what others can't, they can support you remotely using teamviewer. But snap the download pic here let me see
Click to expand...
Click to collapse
successnbd said:
show me your device in download mode
Click to expand...
Click to collapse
OK so that's how it looked like:
download-mode
after writing this post I realized that I haven't tried flashing an OEM rev3 firmware
so I downloaded one after finding out which one is the right file
and I tried flashing it on a completly other pc than the 2 I've already tried it on
and it worked:victory:
here's the recovery after the successful flash:
recovery
So I've been tasked to fix this error by flashing an operating system; the device does not charge and is stuck in a boot loop (refer to the title for the error I'm getting). I've tried using Odin many time and I keep getting a connection error or a repartition error. I have also tried using ADB but I can't get it to show the prompt I need it to (I cannot boot into Android and enable USB Debugging). I've gone through multiple cables/PCs and nothing works. I keep getting the same results and I'm running out of time to do this. I have also confirmed that the firmware I want to flash matches my device model/region; and it is the stock firmware I am trying to install.
I also know absolutely nothing about how Android works since I myself am an iOS user, so forgive me for my naivety if its an issue lol
Any ideas?
pudiste solucionarlo?
Mod translation via GT: were you able to fix it?
I have exactly the same problem could not flash amy firmware with Odin but the firmware matches my device model and region too. Did you have any sucess ?