Flashed Build HWI69 for US Retail on a Canadian wifi MZ604 xoom..tired of
waiting for 3.1 update.
adb reboot bootloader
fastboot oem unlock
adb reboot bootloader
Xoom will then reboot into bootloader screen
fastboot flash boot boot.img
fastboot flash system system.img
fastboot flash recovery recovery.img
fastboot flash userdata userdata.img
fastboot erase cache
fastboot oem lock
fastboot reboot
It is stuck on Starting RSD mode 2.
I can not get it to fastboot protocol...device does not turn off.
Any solutions?
Fastboot OEM lock is where you went wrong. Anyway see this thread.
OK I did this procedure yesterday but did not relock (I know it says to on the moto site but the guide I read said not to).
Anyway, pressing power and vol up will force a reboot. Unsure what will happen when it boots back up though...!
You should be fine. Only trying to relock will cause this error.
To get back to fastboot after a bad lock do this.
Power button and volume up, this will reboot the device.
As soon as the screen turns back on holds down power and volume down. In about 60 seconds your device should go to fastboot. Do not let go until it gets there.
Sent From My Evo
Thanks for the reply . It now says Failed to boot LNX 0X0004
Starting Fastboot protocol support
However it will not connect to xoom.
<wait for device> when issue fastboot command.
What the hell is going on?
you need to read this thread
http://forum.xda-developers.com/showthread.php?t=1108518
The exact thread I linked to...(-__-)'
I followed instruction from motorla dev support site.
"h**p://developer.motorola.com/products/software/?pubid=987654"
It uses command "fastboot oem lock"! So why did locking brick the device?
here it is:
Device Software Images
Select the appropriate device software image to download and re-lock your device. If you need to find your build number on your Motorola device go to Settings and About Phone or About Tablet.
The commands to flash and re-lock your device are as follows:
fastboot flash boot boot.img
fastboot flash system system.img
fastboot flash recovery recovery.img
fastboot flash userdata userdata.img
fastboot erase cache
fastboot oem lock
Note: If no userdata.img file is present in your download, please issue the command:
fastboot erase userdata
The Moto instructions are for locking the device back to it's own image. You are not using your device's own image. Every guide I've seen on here tells you not to relock, regardless of what Moto say. Believe the devs.
Thanxs
I now believe the devs......
Thanks for the reply. Sent the beast out to moto Canada today.
tfx1 said:
I now believe the devs......
Thanks for the reply. Sent the beast out to moto Canada today.
Click to expand...
Click to collapse
Try making or obtaining a factory cable which its different from an OTG cable. Start with the two links below. This might save the day.
http://forum.xda-developers.com/showthread.php?t=1077414
http://forum.xda-developers.com/showthread.php?t=1108518
Hey guys, do you have any idea how I can solve this issue? If I turn on the moto, all the time I access fastboot mode. Then I have to click volume up to get started
I switched to latest 4.4.2 GPE though
Thank you very much
It says:
fastboot reason utag boot mode configured as fastboot
Try this:
Code:
fastboot oem fb_mode_clear
Work fine this Fastboot command
I tried to root my MOTO G 2015 XT1550 using KINGROOT app.At that time it was running marshmallow 6.01 ,after running the kingroot application the phone restarted and stuck in startup menu with fastboot mode.Please help me out of this
Are u able to open stock recivery?
And have unlocked bootloader?
Amirphp said:
Are u able to open stock recivery?
And have unlocked bootloader?
Click to expand...
Click to collapse
No,I have not unlocked the bootloader,what i did was that i installed kingroot app and tried to root from the app.I don't know what it did to my device but now its stuck in fastboot mode.Please tell me how to open stock recovery.
divyandu said:
I tried to root my MOTO G 2015 XT1550 using KINGROOT app.At that time it was running marshmallow 6.01 ,after running the kingroot application the phone restarted and stuck in startup menu with fastboot mode.Please help me out of this
Click to expand...
Click to collapse
1. Stay calm.
1.a You cannot root your phone without unlocking bootloader.
1.b. You will need to do a thorough reading of how to unlock bootloader from threads in this forum or else where. You will also need to read and understand the process of fastboot mode of flashing stock firmware.
2. Since you are able to enter fastboot mode connect your mobile to your PC with your USB chord, open the minimal adb fastboot mode, try to get the unlock key, visit Motorola site and get your bootloader unlock key. There are other threads explaning how to do this. Download the correct stock firmware identified based on the phone model no. Eg xt1550 dual sim and store it onto your PC, you will also need the minimal adb fastboot file, Motorola drivers, twrp3.0., SuperSU 2.62-3 ( no other version of SuperSU works, only this version)
3. Once you unlock your bootloader, flash the stock firmware which you need to download from other thread of this forum using fastboot mode. Note, marshmallow 6.0.1 has 7 sparsechunk files. So be careful about fast boot commands. Do not use the commands you find on the stock firmware thread blindly as these have commands only for 6 sparsechunk files. You may open the flash file from the downloaded firmware to get an idea of all the commands to be typed and their respective partitions too.
4. Flash twrp to replace stock recovery. Enter recovery from fastboot mode using volume keys to navigate and powerkey to select.
5. Once into twrp, press mounts tab and tick to mount USB storage, and copy the SuperSU 2.62-3 file into the external memory card of your phone from pc. Install this SuperSU.zip file without unzipping it by pressing the install tab in twrp home screen and selecting the zip file and sliding the installer.
6. Reboot system. Done! You have your phone rooted the perfect way.
When I switch on my device(moto g3) the following message appears.
Start Up Failed
Your device didn't startup successfully.
Use the Software Repair Assistant on your computer to repair your device.
Connect your device to your computer to get the Software Repair Assistant.
AP Fastboot Flash Mode (Secure)
Failed to verify hab image boot
failed to validate boot image
ERROR: Failed to pass validation,backup to fastboot
Boot up failed
Please help with a solution asap??
divyandu said:
When I switch on my device(moto g3) the following message appears.
Start Up Failed
Your device didn't startup successfully.
Use the Software Repair Assistant on your computer to repair your device.
Connect your device to your computer to get the Software Repair Assistant.
AP Fastboot Flash Mode (Secure)
Failed to verify hab image boot
failed to validate boot image
ERROR: Failed to pass validation,backup to fastboot
Boot up failed
Please help with a solution asap??
Click to expand...
Click to collapse
Dear friend please have patience...
These things require a cool mind...
Did you try the hardware way of entering the fastboot mode? If not keep the volume down and power button pressed for some time till ulyou enter fastboot mode. Basically there is no info if you have tried to follow what was given earlier...have you tried it?
I am unable to unlock the bootloader from adb.
The problem I think is that my phone's USB debugging is off.Anybody plz tell me how do I turn my bootloader on from fastboot or recovery mode.
divyandu said:
No,I have not unlocked the bootloader,what i did was that i installed kingroot app and tried to root from the app.I don't know what it did to my device but now its stuck in fastboot mode.Please tell me how to open stock recovery.
Click to expand...
Click to collapse
@divyandu follow this and let me know if it works.
http://forum.xda-developers.com/2015...k-6-0-t3349468
you can get the Factory Firmware's on this Link.
http://forum.xda-developers.com/2015...mages-t3169639
divyandu said:
I am unable to unlock the bootloader from adb.
The problem I think is that my phone's USB debugging is off.Anybody plz tell me how do I turn my bootloader on from fastboot or recovery mode.
Click to expand...
Click to collapse
Dear friend,
You need not have your bootloader unlocked to flash factory firmware
Quote from the XDA forum factory firmware link:
"Frequently Asked Questions:
Can I restore Factory Firmware if my Bootloader is locked?
Yes."
And if you are still stuck with a phone stuck at logo or is looping at the boot, either follow steps given elsewhere in this forum or follow the method that I am enumerating below which is what I would have done (which in principle is same as given elsewhere).
Getting your phone revived is your first priority. Unlocking bootloader and rooting is secondary.
You would be needing a pc with administrator privilege, internet connection and of course your phone along with the usb cable.
You would be needing the drivers for your phone, minimal adb and fastboot files, stock firmware for your phone model. All these files are available in the XDA forum as per links provided by others or as per this link
http://forum.xda-developers.com/2015-moto-g/general/guide-fastboot-flashing-factory-t3187750
1. Correctly install drivers onto your pc using administrator privileges.
2. Unzip and Install the minimal adb and fastboot files onto your pc into some specific directory and click the executable files once. This would ensure that all the files are loaded and dos prompt recognizes the adb and fastboot commands (commands are different for ADB stage and FASTBOOT stage, what you are going to use is directly the fastboot stage commands given below). Install as an administrator. Note this specific directory and file where you unzipped and installed the minimal adb file as you will need it in the below step.
3. Download the stock 6.0.1 mm firmware for XT1550 from the link below store it in you pc.
http://forum.xda-developers.com/2015-moto-g/general/index-moto-g-factory-firmware-images-t3169639
Unzip the stock firmware. Now copy all the files of the stock firmware (all of them) into the specific file of the minimal adb and fastboot which you unzipped into and installed earlier and noted the location. You need to copy all the firmware files into the minimal adb and fastboot directory as that way you avoid specifying the location of the files for each flash command which is both simple and saves us from a lot of mistakes.
4. After copying all the unzipped stock firmware files in the minimal adb fastboot directory, press the shift button on keyboard and right click the mouse on the screen where in a dialogue box appears and choose to open the command prompt in this directory. This will open a command prompt with default reference to the current directory.
5. In what ever condition your phone is in (other than the fastboot mode), press simultaneously the volume down key + power button together for about 8-10 secs. This action will automatically lead your phone to enter the fastboot mode. After entering the fastboot mode you can connect the phone to your pc using a usb cable and your pc should ring a note that it has detected the phone. To check if the pc has detected the phone and the link is established, type the following command in the command prompt window which you opened in step 4
fastboot devices
This command displays your device number if all is well in the command prompt window. NOW you are ready to flash the stock firmware I.E. after successful detection of the phone by your pc.
6. Carefully type each and every of the commands in italics or copy and paste them ONE by ONE and wait for each command to be executed. The commands are being given below to help you (these are for flashing the 6.0.1mm onto the XT1550 only) in the opened command prompt window (Ensure that you do not miss any of the commands and follow the order given below) :
fastboot oem fb_mode_set
fastboot flash partition gpt.bin
fastboot flash bootloader bootloader.img
fastboot flash logo logo.bin
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img_sparsechunk.0
fastboot flash system system.img_sparsechunk.1
fastboot flash system system.img_sparsechunk.2
fastboot flash system system.img_sparsechunk.3
fastboot flash system system.img_sparsechunk.4
fastboot flash system system.img_sparsechunk.5
fastboot flash system system.img_sparsechunk.6
fastboot flash system system.img_sparsechunk.7
fastboot flash modem NON-HLOS.bin
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
fastboot erase cache
fastboot erase userdata
fastboot erase customize
fastboot erase clogo
fastboot oem fb_mode_clear
fastboot reboot
If you have done every thing correctly till now you should see the command prompt returning a OKAY afer each command with the time taken for flashing each file. This should revive your device first.
After this you may try unlocking the bootloader and rooting as the next step. But be patient and retain a cool head to read first and think clearly..... you will need it a lot as is necessary for such things... good luck and happy learning!!
Follow the instructions in this thread ...to unlock bootloader and root...
Works 100%.
http://forum.xda-developers.com/2015-moto-g/general/root-how-to-root-moto-g-2015-android-t3320113
arunhebbare said:
Dear friend,
You need not have your bootloader unlocked to flash factory firmware
Quote from the XDA forum factory firmware link:
"Frequently Asked Questions:
Can I restore Factory Firmware if my Bootloader is locked?
Yes."
And if you are still stuck with a phone stuck at logo or is looping at the boot, either follow steps given elsewhere in this forum or follow the method that I am enumerating below which is what I would have done (which in principle is same as given elsewhere).
Getting your phone revived is your first priority. Unlocking bootloader and rooting is secondary.
You would be needing a pc with administrator privilege, internet connection and of course your phone along with the usb cable.
You would be needing the drivers for your phone, minimal adb and fastboot files, stock firmware for your phone model. All these files are available in the XDA forum as per links provided by others or as per this link
http://forum.xda-developers.com/2015-moto-g/general/guide-fastboot-flashing-factory-t3187750
1. Correctly install drivers onto your pc using administrator privileges.
2. Unzip and Install the minimal adb and fastboot files onto your pc into some specific directory and click the executable files once. This would ensure that all the files are loaded and dos prompt recognizes the adb and fastboot commands (commands are different for ADB stage and FASTBOOT stage, what you are going to use is directly the fastboot stage commands given below). Install as an administrator. Note this specific directory and file where you unzipped and installed the minimal adb file as you will need it in the below step.
3. Download the stock 6.0.1 mm firmware for XT1550 from the link below store it in you pc.
http://forum.xda-developers.com/2015-moto-g/general/index-moto-g-factory-firmware-images-t3169639
Unzip the stock firmware. Now copy all the files of the stock firmware (all of them) into the specific file of the minimal adb and fastboot which you unzipped into and installed earlier and noted the location. You need to copy all the firmware files into the minimal adb and fastboot directory as that way you avoid specifying the location of the files for each flash command which is both simple and saves us from a lot of mistakes.
4. After copying all the unzipped stock firmware files in the minimal adb fastboot directory, press the shift button on keyboard and right click the mouse on the screen where in a dialogue box appears and choose to open the command prompt in this directory. This will open a command prompt with default reference to the current directory.
5. In what ever condition your phone is in (other than the fastboot mode), press simultaneously the volume down key + power button together for about 8-10 secs. This action will automatically lead your phone to enter the fastboot mode. After entering the fastboot mode you can connect the phone to your pc using a usb cable and your pc should ring a note that it has detected the phone. To check if the pc has detected the phone and the link is established, type the following command in the command prompt window which you opened in step 4
fastboot devices
This command displays your device number if all is well in the command prompt window. NOW you are ready to flash the stock firmware I.E. after successful detection of the phone by your pc.
6. Carefully type each and every of the commands in italics or copy and paste them ONE by ONE and wait for each command to be executed. The commands are being given below to help you (these are for flashing the 6.0.1mm onto the XT1550 only) in the opened command prompt window (Ensure that you do not miss any of the commands and follow the order given below) :
fastboot oem fb_mode_set
fastboot flash partition gpt.bin
fastboot flash bootloader bootloader.img
fastboot flash logo logo.bin
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img_sparsechunk.0
fastboot flash system system.img_sparsechunk.1
fastboot flash system system.img_sparsechunk.2
fastboot flash system system.img_sparsechunk.3
fastboot flash system system.img_sparsechunk.4
fastboot flash system system.img_sparsechunk.5
fastboot flash system system.img_sparsechunk.6
fastboot flash system system.img_sparsechunk.7
fastboot flash modem NON-HLOS.bin
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
fastboot erase cache
fastboot erase userdata
fastboot erase customize
fastboot erase clogo
fastboot oem fb_mode_clear
fastboot reboot
If you have done every thing correctly till now you should see the command prompt returning a OKAY afer each command with the time taken for flashing each file. This should revive your device first.
After this you may try unlocking the bootloader and rooting as the next step. But be patient and retain a cool head to read first and think clearly..... you will need it a lot as is necessary for such things... good luck and happy learning!!
Click to expand...
Click to collapse
Ty everyone for the support and the quick answers.My phone is unbricked and is running 6.0.1
Special thanks arunhebbare your suggestion worked out finally
I tried to root my MOTO G 2015 XT1550 using KINGROOT app.At that time it was running marshmallow 6.01 ,after running the kingroot application the phone restarted and stuck in startup menu with fastboot mode.
:crying: When I switch on my device(moto g3) the following message appears.
Start Up Failed
Your device didn't startup successfully.
Use the Software Repair Assistant on your computer to repair your device.
Connect your device to your computer to get the Software Repair Assistant.
AP Fastboot Flash Mode (Secure)
Failed to verify hab image boot
failed to validate boot image
ERROR: Failed to pass validation,backup to fastboot
Boot up failed
plz help me
vidya_sagar said:
I tried to root my MOTO G 2015 XT1550 using KINGROOT app.At that time it was running marshmallow 6.01 ,after running the kingroot application the phone restarted and stuck in startup menu with fastboot mode.
:crying: When I switch on my device(moto g3) the following message appears.
Start Up Failed
Your device didn't startup successfully.
Use the Software Repair Assistant on your computer to repair your device.
Connect your device to your computer to get the Software Repair Assistant.
AP Fastboot Flash Mode (Secure)
Failed to verify hab image boot
failed to validate boot image
ERROR: Failed to pass validation,backup to fastboot
Boot up failed
plz help me
Click to expand...
Click to collapse
You tried the above solution a few posts back??
Broadcasted from Zeta Reticuli
Gravemind2015 said:
You tried the above solution a few posts back??
Broadcasted from Zeta Reticuli
Click to expand...
Click to collapse
i'm not sure about Enabling USB debugging. is that above process will work??when i don't enable usb debugging?
tnx for ur reply
---------- Post added at 10:45 AM ---------- Previous post was at 10:07 AM ----------
vidya_sagar said:
i'm not sure about Enabling USB debugging. is that above process will work??when i don't enable usb debugging?
tnx for ur reply
Click to expand...
Click to collapse
if u dont mind can u post the vedio of this process
bad
iam unlocked my boot loader in my moto g3 running 6.0.1...after i try to flash twrp to root ..but it is no worked ..so i use king root app to root my phone root installed successfully ...but my sims signels are not showing ...so i do hard reset ...after phone is on and stucks at language selection what should i do
vidya_sagar said:
i'm not sure about Enabling USB debugging. is that above process will work??when i don't enable usb debugging?
tnx for ur reply
---------- Post added at 10:45 AM ---------- Previous post was at 10:07 AM ----------
if u dont mind can u post the vedio of this process
Click to expand...
Click to collapse
My internet is not fast enough for a video upload sorry. But if you are not sure about the process you can search lost101's firmware flashing guide in general section. I have flashed it and it works.
Broadcasted from Zeta Reticuli
ok reading other threads i see others having issues with flashing twrp also.
i followed the unlock procedure and it was a sucess.
procedure:
in command prompt with files in directory
1: adb reboot-bootloader
2: fastboot -i 0x1bbb oem unlock
3: fastboot -i 0x1bbb oem device-info (bootloader confirmed unlocked)
4: fastboot -i 0x1bbb reboot
5: let deviice reboot
6: adb reboot-bootloader
7: got files from here http://forum.xda-developers.com/idol-3/general/twrp-custom-recovery-idol3-6045-t3162608
8: fastboot -i 0x1bbb flash recovery twrp-2.8.7.0-idol3.img
10: rebooted
11: scratched head as default recovery booted.
so i am assuming i need to apply root before flashing custom recovery?
thanks in advance for any help provided.
I'm not sure there is any difference between the 5.5" & the 4.7" in term of the procedure but here's what I did on my 5.5"
1. Get ADB SDK application installed on PC
2. Download and install the correct USB driver for the phone. Assume you already downloaded the custom TWRP recovery image
3. Enable USB debugging mode on the phone
4. Plugin the phone to the PC, open Command Prompt
a. adb devices // to make sure the phone is recognized and listed
b. adb reboot bootloader
c. fastboot -i 0x1bbb flash recovery twrp-2.8.7.0-idol3.img // browse to where the .img is located first
Should be it!
You can root it AFTER install the custom recovery.
Hope that help!
deamon1311 said:
ok reading other threads i see others having issues with flashing twrp also.
i followed the unlock procedure and it was a sucess.
procedure:
in command prompt with files in directory
1: adb reboot-bootloader
2: fastboot -i 0x1bbb oem unlock
3: fastboot -i 0x1bbb oem device-info (bootloader confirmed unlocked)
4: fastboot -i 0x1bbb reboot
5: let deviice reboot
6: adb reboot-bootloader
7: got files from here http://forum.xda-developers.com/idol-3/general/twrp-custom-recovery-idol3-6045-t3162608
8: fastboot -i 0x1bbb flash recovery twrp-2.8.7.0-idol3.img
10: rebooted
11: scratched head as default recovery booted.
so i am assuming i need to apply root before flashing custom recovery?
thanks in advance for any help provided.
Click to expand...
Click to collapse
I had to use Flashify to get it to stick on my 60450. Otherwise, I would have to use commands to get it to boot into TWRP rather than stock.
5.5" cricket here.
it boots into twrp till it loads the os wich seems to repair the recovery.
be annoying if it is self repaiiring.
ok root applied.
how do i flashify twrp.
Oneplus 7 pro android 11
downloaded adb from web on linux
unlocked bootloader
then goto fastboot and flashed twrp tried to recovery but got stuck at fastboot
i tried everything that i found on internet
i found that this device has 2 slots thats confused me.
help!
To exit Fastboot mode try this
Code:
fastboot devices
fastboot reboot
jwoegerbauer said:
To exit Fastboot mode try this
Code:
fastboot devices
fastboot reboot
Click to expand...
Click to collapse
its work in terminal but not in the device.
everytime i tried it start with bootup logo and endup with fastboot mode.