Database Info

help with s-on

Can someone please help, I'm truly stuck here.
I have followed the guide here..
http://forum.xda-developers.com/show....php?t=1460713
I have managed to remove the revolutionary logo, and all was good. I then attempted to install the following RUU...
RUU_Saga_HTC_Europe_1.28.401.1_Radio_20.28b.30.080 5U_38.03.02.11_M_release_177977_signed
Went through all the prompts but the program "hung" at the sending screen. After around an hour I pulled the usb cable, yay the phone still boots. However I was still at the old HBOOT (cant remember the numbers 6.0.0002 or something ) and with the custom rom.
Though this might be a problem with the RUU... NAY.
I have since tried he following..
RUU_Saga_HTC_Europe_1.47.401.4_Radio_20.28I.30.085 AU_3805.06.02.03_M_release_199410_signed
RUU_Saga_S_HTC_Europe_2.10.401.5_Radio_20.4801.30. 0822U_3822.10.08.04_M_release_219480_signed
RUU_Saga_O2_UK_1.31.206.1_Radio_20.28b.30.0805U_38 .03.02.14_M_release_178935_signed
All with the same results.
So I downgraded the hboot manually to 0.98.0002 and tried them all again. Still no luck.
The reason I have tried the different RUU is that it was originally from carphone warehouse. Their phones are generally unbranded so assumed it would be a standard euro ruu.
Please help.

I really don't get what the problem is. Removing the "Revolutionary" logo isn't the same as being S-ON. But check out the link below to see if it helps.
forum.xda-developers.com/showthread.php?t=1549636

@pttynan
PLease run the fastboot command "fastboot getvar all" remember to remove your imei and serial from your post.
Then I will direct you to a solution

foX2delta said:
@pttynan
PLease run the fastboot command "fastboot getvar all" remember to remove your imei and serial from your post.
Then I will direct you to a solution
Click to expand...
Click to collapse
Hi Fox2delta. The command gives the following.
INFOversion: 0.5
INFOversion-bootloader: 0.98.2000
INFOversion-baseband: 38.03.02.11
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 1.28.401.1
INFOserialno: HT13Jxxxxxxxx
INFOimei: 3550670xxxxxxxxx
INFOproduct: saga
INFOplatform: HBOOT-7230
INFOmodelid: PG8810000
INFOcidnum: HTC__001
INFObattery-status: good
INFObattery-voltage: 4136mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: ENG
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 7b851d36
INFOhbootpreupdate: 12
INFOgencheckpt: 0
all: Done!
finished. total time: 0.031s

Dont suppose anyone has any thoughts on this? Carphone flat out refused to touch it once the noticed S-OFF

[q] phone stuck in hboot with nothing else!!

hey, my phone is spoilt and im in desperate help of somebody who can help me with my HTC Sensation XE w Audio Beats.
This is what happened,
i was trying to root my phone with help from hansoon all in one toolkit, after unlocking the device and trying my best to install recovery it comes to no avail, had been receiving error when tryng to install / flash pg58img from hboot ( model id incorrect ) . later after i accidentally click on flash kernel and my phone restarted on its own and got stuck in hboot thereafter. I don't have recovery, no USB debugging mode for me to superCID and ive search the whole entire forum for a cure.. i really wish somebody would help me out here as i really want to get my only phone working and running.
UNLOCKED
pyramid pvt ship s-on rl
hboot. 1.27.0000
emmc-boot
thats all i have, i apprieciate anybody who is willing to help me thank you so much!

yuzhi92 said:
hey, my phone is spoilt and im in desperate help of somebody who can help me with my HTC Sensation XE w Audio Beats.
This is what happened,
i was trying to root my phone with help from hansoon all in one toolkit, after unlocking the device and trying my best to install recovery it comes to no avail, had been receiving error when tryng to install / flash pg58img from hboot ( model id incorrect ) . later after i accidentally click on flash kernel and my phone restarted on its own and got stuck in hboot thereafter. I don't have recovery, no USB debugging mode for me to superCID and ive search the whole entire forum for a cure.. i really wish somebody would help me out here as i really want to get my only phone working and running.
UNLOCKED
pyramid pvt ship s-on rl
hboot. 1.27.0000
emmc-boot
thats all i have, i apprieciate anybody who is willing to help me thank you so much!
Click to expand...
Click to collapse
Go to fastboot on your device
Connect it to pc (usb debugging enable is not required) (phone reads fastboot usb)
Then go to your adb folder on pc
And Type this
fastboot getvar all
Post the complete output except imei and serial number
I'll guide you through the process after this
Sent from my pyramid.. Through blazing fast sonic waves

Just download the latest RUU for your device and run it

Yeah do that lol u can get ur ruu from file factory
Sent from my HTC One S using xda premium

[SOLVED] OP's problem was solved on the irc over 5 hours ago.

Stuck in the same boot loop with my htc sensation
i just tried to flash my htc sensation xe for the first time, i successfully did S-OFF using the revolutionary tool and then tried to install ClockworkMod Recovery from PG58IMG.zip which succeeded,
but i havent been able to boot up the device since doing that. its stuck on the htc logo. kindly help.
this is what i get on doing c:\adb>fastboot getvar all
INFOversion: 0.5
INFOversion-bootloader: 1.27.1100
INFOversion-baseband: N/A
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 3.32.401.5
INFOserialno: SH1AJV804923
INFOimei: 358313047099531
INFOproduct: pyramid
INFOplatform: HBOOT-8260
INFOmodelid: PG5813001
INFOcidnum: HTC__038
INFObattery-status: good
INFObattery-voltage: 3811mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 617f0a98
INFOhbootpreupdate: 11
INFOgencheckpt: 0
all: Done!
finished. total time: 0.499s

reresp same
im having a similar problem - does anyone know what the solution was
edit: pretty much the same thing
stuck with the fastboot/cwr but can't get anything else to work
tried multiple RUU already

xenonxeno said:
i just tried to flash my htc sensation xe for the first time, i successfully did S-OFF using the revolutionary tool and then tried to install ClockworkMod Recovery from PG58IMG.zip which succeeded,
but i havent been able to boot up the device since doing that. its stuck on the htc logo. kindly help.
this is what i get on doing c:\adb>fastboot getvar all
INFOversion: 0.5
INFOversion-bootloader: 1.27.1100
INFOversion-baseband: N/A
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 3.32.401.5
INFOserialno: SH1AJV804923
INFOimei: 358313047099531
INFOproduct: pyramid
INFOplatform: HBOOT-8260
INFOmodelid: PG5813001
INFOcidnum: HTC__038
INFObattery-status: good
INFObattery-voltage: 3811mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 617f0a98
INFOhbootpreupdate: 11
INFOgencheckpt: 0
all: Done!
finished. total time: 0.499s
Click to expand...
Click to collapse
What is the last rom you had?
You can still go to bootloader thus you can go to recovery...
So enter recovery and tell me whether you are able to e ter or not
Sent from my pyramid.. Through blazing fast sonic waves

w00dberry said:
im having a similar problem - does anyone know what the solution was
edit: pretty much the same thing
stuck with the fastboot/cwr but can't get anything else to work
tried multiple RUU already
Click to expand...
Click to collapse
You mean you succesfully flashed RUU and still can't boot?
Sent from my pyramid.. Through blazing fast sonic waves

xenonxeno said:
i just tried to flash my htc sensation xe for the first time, i successfully did S-OFF using the revolutionary tool and then tried to install ClockworkMod Recovery from PG58IMG.zip which succeeded,
but i havent been able to boot up the device since doing that. its stuck on the htc logo. kindly help.
this is what i get on doing c:\adb>fastboot getvar all
INFOversion: 0.5
INFOversion-bootloader: 1.27.1100
INFOversion-baseband: N/A
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 3.32.401.5
INFOserialno: SH1AJV804923
INFOimei: 358313047099531
INFOproduct: pyramid
INFOplatform: HBOOT-8260
INFOmodelid: PG5813001
INFOcidnum: HTC__038
INFObattery-status: good
INFObattery-voltage: 3811mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 617f0a98
INFOhbootpreupdate: 11
INFOgencheckpt: 0
all: Done!
finished. total time: 0.499s
Click to expand...
Click to collapse
Flash an ICS ROM. Your GB ROM will not boot on 3.32 firmware.
---------- Post added at 11:28 AM ---------- Previous post was at 11:26 AM ----------
w00dberry said:
im having a similar problem - does anyone know what the solution was
edit: pretty much the same thing
stuck with the fastboot/cwr but can't get anything else to work
tried multiple RUU already
Click to expand...
Click to collapse
I need a better description of the problem.
"It doesn't work" "I tried multiple RUUs" are useless to me.
What happens when you flash the RUU? Is it successful?

[Q] Weird Problem With HTC Sensation XE

Hello guys
I have a problem with my HTC Sensation XE.
I jtag'ed the phone with RIFF Jtag box (changed IMEI, s-off'ed and rewrote boot). After that the phone started to reset itself over and over. After that by using RIFF box, I erased, rewrote boot and tried 5 or 6 different RUU's.
Now, I can open the phone (it vibrates and I can hear HTC opening voice) but the screen is completely black. I tried to send a call to this device and it received the call but I could not answer the call. So everything but screen looks like working.
Screen problem occured after jtag so I think it is not a hardware issue but I am not sure.
I am searching for 3 weeks now but I could not find a satisfactory answer. Can you help me to fix this problem. Any ideas? suggestions? Is there something that I might do wrong?
Thanks for your answers and sorry for my bad English and terminology.

kmrock said:
Hello guys
I have a problem with my HTC Sensation XE.
I jtag'ed the phone with RIFF Jtag box (changed IMEI, s-off'ed and rewrote boot). After that the phone started to reset itself over and over. After that by using RIFF box, I erased, rewrote boot and tried 5 or 6 different RUU's.
Now, I can open the phone (it vibrates and I can hear HTC opening voice) but the screen is completely black. I tried to send a call to this device and it received the call but I could not answer the call. So everything but screen looks like working.
Screen problem occured after jtag so I think it is not a hardware issue but I am not sure.
I am searching for 3 weeks now but I could not find a satisfactory answer. Can you help me to fix this problem. Any ideas? suggestions? Is there something that I might do wrong?
Thanks for your answers and sorry for my bad English and terminology.
Click to expand...
Click to collapse
hmm you did some advanced stuff ...pushing boot and other files using jtag ...can you now go into bootloader ? also there too the screen is blank ?
if you can go to bootloader ..why not try running ruu manually? (not jtag this time )

ganeshp said:
hmm you did some advanced stuff ...pushing boot and other files using jtag ...can you now go into bootloader ? also there too the screen is blank ?
if you can go to bootloader ..why not try running ruu manually? (not jtag this time )
Click to expand...
Click to collapse
Hello, first of all, thanks for your answer.
Unfortunately now same black screen appears in the bootloader screen. Before erase operation I could go into the bootloader but after erase, I can not see the screen.

kmrock said:
Hello, first of all, thanks for your answer.
Unfortunately now same black screen appears in the bootloader screen. Before erase operation I could go into the bootloader but after erase, I can not see the screen.
Click to expand...
Click to collapse
Looks like some important partition got wiped.. So ruu flash is best choice
Can you confirm that the device in bootloader
By typing this command in the command prompt from your adb folder (assuming that you have adb/fastboot setup)
And you need to connect your device to pc though
fastboot devices
(the phone serial number should be shown)
If it's working fine
Can you post the complete output of the following command too?
fastboot getvar all ( except imei and serial number)
Then we can see what state your current device is in and can determine which RUU to run
Sent from my pyramid.. Through blazing fast sonic waves

kmrock said:
Hello, first of all, thanks for your answer.
Unfortunately now same black screen appears in the bootloader screen. Before erase operation I could go into the bootloader but after erase, I can not see the screen.
Click to expand...
Click to collapse
Did you JTAG it yourself? if so when you reassembled the phone did you make sure that the 2 cables you had to disconnect from the cpu mainboard were properly reconnected?

Jonny said:
Did you JTAG it yourself? if so when you reassembled the phone did you make sure that the 2 cables you had to disconnect from the cpu mainboard were properly reconnected?
Click to expand...
Click to collapse
Yes, check this.
It doesn't sound like you flashed any partitions that shouldn't have been touched / would affect the display. And if so, it sounds like it'd be a partition not included in RUUs.

Hello everybody, thanks for your answers.
Jonny said:
Did you JTAG it yourself? if so when you reassembled the phone did you make sure that the 2 cables you had to disconnect from the cpu mainboard were properly reconnected?
Click to expand...
Click to collapse
Yes I JTAGd it myself (with the owner of the RIFF BOX with me). I double checked all the cables and sockets and everything seems fine.
ganeshp said:
Looks like some important partition got wiped.. So ruu flash is best choice
Can you confirm that the device in bootloader
By typing this command in the command prompt from your adb folder (assuming that you have adb/fastboot setup)
And you need to connect your device to pc though
fastboot devices
(the phone serial number should be shown)
If it's working fine
Can you post the complete output of the following command too?
fastboot getvar all ( except imei and serial number)
Then we can see what state your current device is in and can determine which RUU to run
Sent from my pyramid.. Through blazing fast sonic waves
Click to expand...
Click to collapse
Here is the output:
Code:
C:\Windows\system32>fastboot devices
************ fastboot
C:\Windows\system32>fastboot getvar all
INFOversion: 0.5
INFOversion-bootloader: 1.27.0000
INFOversion-baseband: N/A
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 3.32.401.105
INFOserialno: ************
INFOimei: ***************
INFOproduct: pyramid
INFOplatform: HBOOT-8260
INFOmodelid: PG58*****
INFOcidnum: HTC__032
INFObattery-status: good
INFObattery-voltage: 4201mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 617f0a98
INFOhbootpreupdate: 11
INFOgencheckpt: 0
all: Done!
finished. total time: 0.505s
Thanks for your help.

kmrock said:
Hello everybody, thanks for your answers.
Yes I JTAGd it myself (with the owner of the RIFF BOX with me). I double checked all the cables and sockets and everything seems fine.
Here is the output:
Code:
C:\Windows\system32>fastboot devices
************ fastboot
C:\Windows\system32>fastboot getvar all
INFOversion: 0.5
INFOversion-bootloader: 1.27.0000
INFOversion-baseband: N/A
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 3.32.401.105
INFOserialno: ************
INFOimei: ***************
INFOproduct: pyramid
INFOplatform: HBOOT-8260
INFOmodelid: PG58*****
INFOcidnum: HTC__032
INFObattery-status: good
INFObattery-voltage: 4201mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 617f0a98
INFOhbootpreupdate: 11
INFOgencheckpt: 0
all: Done!
finished. total time: 0.505s
Thanks for your help.
Click to expand...
Click to collapse
ok the HTC__032 is of east europe
so try this RUU
(run the ruu on pc with phone connected in bootloader mode (check using fastboot devices))
http://www.filefactory.com/file/70cre7fl6rol/n/RUU_PYRAMID_LE_ICS_35_S_HTC_Europe_3.32.401.105_R2_Radio_11.69.3504.00U_11.22.3504.07_M_release_253443_signed.exe
if cid failed error came
then change the cid to HTC__001 (two underscores remember)
fastboot oem writecid HTC__001
fastboot reboot-bootloader
fastboot getvar cid (verify the cid from the output of this command)
then run the same RUU again

Hello
I downloaded the file and installed it successfully (no cid failed error)
However same behavior continues. Here is the fastboot getvar all output:
Code:
C:\Windows\system32>fastboot getvar all
INFOversion: 0.5
INFOversion-bootloader: 1.29.0000
INFOversion-baseband: N/A
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 3.32.401.105
INFOserialno: -------------
INFOimei: ---------------
INFOproduct: pyramid
INFOplatform: HBOOT-8260
INFOmodelid: PG58*****
INFOcidnum: HTC__032
INFObattery-status: good
INFObattery-voltage: 4213mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 705f86f6
INFOhbootpreupdate: 11
INFOgencheckpt: 0
all: Done!
Any ideas? suggestions?
Thanks

kmrock said:
Hello
I downloaded the file and installed it successfully (no cid failed error)
However same behavior continues. Here is the fastboot getvar all output:
Code:
C:\Windows\system32>fastboot getvar all
INFOversion: 0.5
INFOversion-bootloader: 1.29.0000
INFOversion-baseband: N/A
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 3.32.401.105
INFOserialno: -------------
INFOimei: ---------------
INFOproduct: pyramid
INFOplatform: HBOOT-8260
INFOmodelid: PG58*****
INFOcidnum: HTC__032
INFObattery-status: good
INFObattery-voltage: 4213mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 705f86f6
INFOhbootpreupdate: 11
INFOgencheckpt: 0
all: Done!
Any ideas? suggestions?
Thanks
Click to expand...
Click to collapse
If ruu didn't solved the problem then the digitizer connections were not made proper... Or hardware issue
Sent from my pyramid.. Through blazing fast sonic waves

ganeshp said:
If ruu didn't solved the problem then the digitizer connections were not made proper... Or hardware issue
Sent from my pyramid.. Through blazing fast sonic waves
Click to expand...
Click to collapse
Thanks for your efforts. I disassembled and looked through all sockets and hardware but everything looks fine. If I insert a sim card and start the device it opens. Also it receives calls and reflects to the volume buttons. But whatever I did with touchscreen, I could not get a reaction. So both screen and digitizer won't work.
Thanks for your answers.

Problems/Stuck at HBoot

Hello all :
First the Data :
--------------------------------------------------------------
****Security Warning*****
Saga PVT, Ship S-On RL
HBoot-0.98.0000
Radio 38.03.02.14_M
emmc-boot
March 10 2001, 14:58:38
---------------------------------------------------------------
fastboot getvar all :
INFOversion: 0.5
INFOversion-bootloader: 0.98.0000
INFOversion-baseband: 38.03.02.14_M
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 3.04.401.1
INFOserialno: XXXXXXXXXX
INFOimei: XXXXXXXXXX
INFOproduct: saga
INFOplatform: HBOOT-7230
INFOmodelid: PG8810000
INFOcidnum: O2___102
INFObattery-status: good
INFObattery-voltage: 4060mV
INFOpartition-layout: Generic
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 361a7ba6
INFOhbootpreupdate: 12
INFOgencheckpt: 0
all: Done!
I tried allmost everything i found, but i cannot flash anything.
Maybe the Problems lies on the Stuff i marked with bold Text.
Made a Goldcard under Linux, well i used Cat /sys/class..... and got this
001b534d3030303030100441616500b800 Normal
00b800656141041030303030304d531b00 Reversed
I used that to reverse it by Hand, and gave that to revskills website to download the goldcard.img
Well anyways, there is no chance to get away from the Bootloader.
If i'm using the O2 RUU's i get "140 - Bootloader error" tried it on the normal Way, as well with Rom.zip renamed to PG88IMG.zip
if i use the European RUU "2.10.401.8" comes "Main Version is older" or "CID Error"
tried it on the normal Way, as well with Rom.zip renamed to PG88IMG.zip
I even tried many PG88IMG's from here with Hboot, recovery etc....most gave me a "Signature error"
well i'm like to tinkle, but this time..i'm out of Idea's.
Anyone who's maybe able to help ?

Noone ?

Got it
1. Downloaded the Chinese OTA (http://forumt.xda-developers.com/showthread.php?t=1722571)
2. Got the Firmware.zip out of it
3. Renamed it to PG88IMG.zip
4. That on the SD-Card + reboot into Fastboot/Hboot. (SD-Card must be a Goldcard)
5. Dang it updated to the new Hboot 2.x
6. unlocked the Bootloader with HTCDev
7. installed a Costom Recovery on it (CWM)
8. Installed with that Recovery a Costom-Rom (Fallout for me).
9. used the boot.img to flash boot under the bootloader.
10. used misc_version + O2 RUU to go back to the Stocksystem....as i wanted.

Sensation Stuck on HTC LOGO

Hi guys, i got a HTC Sensation PG5813000 from the friend, and phone doesnt boot, it just hand on HTC logo. And I want to get it work again, I dont know what is reason for that, here is my info abaout phone.
When I turn on it with volume down and power i got this:
=JuopunutBear=
PRYAMID PVT SHIP S-OFF RL
HBOOT-1. 27. 1111
RADIO - 11. 22. 3504. 07_M
OpenADSP-v02. 6. 0 .2226. 00. 0131
eMMC-boot
Jan 13 2012, 17:33:34
And with fastboot getvar all i got this information.
Code:
INFOversion: 0.5
INFOversion-bootloader: 1.27.1111
INFOversion-baseband: 11.22.3504.07_M
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 1.24.401.1
INFOserialno:
INFOimei:
INFOproduct: pyramid
INFOplatform: HBOOT-8260
INFOmodelid: PG5813000
INFOcidnum: 11111111
INFObattery-status: good
INFObattery-voltage: 3782mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 617f0a98
INFOhbootpreupdate: 11
INFOgencheckpt: 0
all: Done!
finished. total time: 0.546s
Can someone help me to bring this phone to live, what ruu I need a download to instal it, radio, image?
Lock, problem solved.

In your shoes, I'd suggest attempting to flash a recovery environment to your phone, such as Clockworkmod or 4EXT.
Boot your phone into the bootloader in the fashion that you have presumably done already (hold down the down volume button and then press the power button for a second or two) and then when the bootloader appears, select Fastboot. Plug your USB cable into your PC (assuming you already have necessary drivers installed; you may need to download HTC Sync if not) and then use the Android Development Bridge (from the Android SDK) to flash a recovery of your choice.
When recently S-Offing and rooting a Sensation XE (a bit over a week ago) I had to start by flashing an older version of Cyanogenmod; CM9, the last official release directly from them, from their website, using some of their instructions here:
http://wiki.cyanogenmod.org/w/Install_CM_for_pyramid
...and the last stable release of CM9 for the Sensation, from here:
http://download.cyanogenmod.org/?type=stable&device=pyramid
After that, I was able to jump to 4EXT and install Shantur's CM11 ROM here:
http://forum.xda-developers.com/showthread.php?t=2692278