Related
My roommate bought an EVO 4G off Craigslist that was pre-flashed to MetroPCS. It had a clean ESN, so I tried to have it activated. I finally got voice and text to work, but no data. After searching the web, visiting flashing stores, and spending hours on the phone with Sprint's so called "Technical Support" over the last week, I finally figured it out...
This is my first tutorial, so bare with me. And I apologize if this is in the wrong forum, it seemed most appropriate. I performed all this in Windows 7 x64.
First you need some software-
1. QPST - http://www.mediafire.com/?m4s81a4zsdbmhen
2. HTC Diag phone drivers - http://www.mediafire.com/?631456zwxi09hh2
3. PRL File 60650 - http://www.corolada.com/prl/
4. I'm not sure if you need ADB installed, but I already did.
5. You will also need to know your MSL. It will most likely be 000000 if your phone is coming from Cricket or MetroPCS.
Now that we have those, we can get to work.
6. Connect your phone via USB and type in ##3424#, your phone should now be in Diag mode. Make sure USB Debugging is ENABLED!
7. Open your device manager in Windows and right click the unknown device "HTC DIAG", Select Update driver.
8. Select Browse my computer for driver. Click select device from list, Click next, Then click "Have Disk" and point to the appropriate HTC Diag driver folder you downloaded.
9. You now should have HTC Modem installed correctly. Right click on it and go to Properties, Then click on the modem tab. Find your port number eg. COM1, COM2, etc.
10. Open up QPST Configuration, Click the PORTS tab. On the bottom right click add port. Add the port you just found from the step above, and hit Enable.
11. Go back to the active phones tab, double click your phone.
12. On the bottom click read from phone. Then save it for a backup.
13. Click on Roaming tab. Find the PRL box, click browse and add your 60650 PRL file you downloaded.
14. Go back to the CDMA tab. Under phone number click the Class 1 box. Enter your phone number (xxx-xxx-xxxx) minus dashes in the box next to Class 1.
15. Click write to phone. Hard parts over!
16. Once that finishes, unplug and reboot your phone.
17. Go to Settings>Update Software>Update PRL then reboot again.
17. Once its back up go into your dialer. Punch in ##3282#. Hit Edit Mode. The password is your MSL.
18. Once in goto Data Profile. Hit Menu then hit RESET.
19. Your phone should now reboot and be able to activate on Sprints network!
I already did this for my roommate, so I am writing this out of memory. I wanted to post pictures but I would have to take CM7 off my phone and redo all of it... grrrr.
Again, this is my first guide so i might have missed something. But I hope not. So many people have helped me here on XDA, so this is my contribution to the community. I hope this helps some people.
I did this to a hero. I believe I just cleared all the ##data stuff and pep update manually.
Sent from my PC36100 using Tapatalk
I tried that to. But the only way to make it work was to flash the new PRL file. Neither Sprint or a Cricket flashing place could fix it. Which I thought was pretty stupid.
Another quick way of doing it.
Load Stock RUU.
This will rewrite PRL, NV items etc back as it rewrites the radio wich controls these.
Once done ##RTN# need MSL to use this, but this will help as well. and your done.
This is handy to have, and even better to have a few different ways to do it.
amoamare said:
Another quick way of doing it.
Load Stock RUU.
This will rewrite PRL, NV items etc back as it rewrites the radio wich controls these.
Once done ##RTN# need MSL to use this, but this will help as well. and your done.
Click to expand...
Click to collapse
Beat me to it.................. This will definitely work.
amoamare said:
Another quick way of doing it.
Load Stock RUU.
This will rewrite PRL, NV items etc back as it rewrites the radio wich controls these.
Once done ##RTN# need MSL to use this, but this will help as well. and your done.
Click to expand...
Click to collapse
thanks to all. this worked for me.
followed the guide, however data and market place is not working
calls and text work fine, any ideas ? thanks
amoamare said:
Another quick way of doing it.
Load Stock RUU.
This will rewrite PRL, NV items etc back as it rewrites the radio wich controls these.
Once done ##RTN# need MSL to use this, but this will help as well. and your done.
Click to expand...
Click to collapse
I tried this like 4 times, and it would never flash the PRL... the way I did it, it finally flashed sprints PRL.
brax said:
followed the guide, however data and market place is not working
calls and text work fine, any ideas ? thanks
Click to expand...
Click to collapse
Go into your phone settings, goto About Phone, what is the PRL number listed?
i am pretty sure i flashed the "60650.prl"
however i sold the phone and it will be back here tomorrow for repairs....
i had the guy do the settings -> update prl without luck....
sigh thanks for any help!
brax said:
i am pretty sure i flashed the "60650.prl"
however i sold the phone and it will be back here tomorrow for repairs....
i had the guy do the settings -> update prl without luck....
sigh thanks for any help!
Click to expand...
Click to collapse
Well if for some reason it didn't flash, then "update PRL" wont work cause its not looking for sprints PRL. Try to see what PRL is loaded on the phone, then I can probably help a little better.
guy claims under settings the prl says 1.77-003
thanks
brax said:
guy claims under settings the prl says 1.77-003
thanks
Click to expand...
Click to collapse
That's the PRI, not PRL. The PRL will be a five digit number. The latest Sprint PRL is 60675.
yeah thats what i figured, didnt know if that was a hex abbreviation with sprint's software for the prl or what... waiting for him to text me back...
i am pretty sure when i waited for him to activate the phone it showed a 3g icon when voice and text went active.. you sure if the prl is wrong everything else would work except data/mms/marketplace? thanks
the prl is = 60675
brax said:
yeah thats what i figured, didnt know if that was a hex abbreviation with sprint's software for the prl or what... waiting for him to text me back...
i am pretty sure when i waited for him to activate the phone it showed a 3g icon when voice and text went active.. you sure if the prl is wrong everything else would work except data/mms/marketplace? thanks
the prl is = 60675
Click to expand...
Click to collapse
Well you have a Sprint PRL. Did the phone go through the Hands Free Activation when you tried to activate it? If you see a 3G symbol then all should be good. You could have him call Sprint and tell them data isn't working and you need to re-activate it...
well we had to type in a diag code then hit update and then it activated, not OTA to get talk and text going... he said he spent a hour at the sprint store today and they couldnt solve it
You could try my guide again, from step 17.
i asked the guy via text to do the guide through 17 to end, he says they tried that at the sprint store... without luck... i guess i can try it tomorrow when the phones in my hands unless anyone else has any other ideas....
what i did was followed this guide after flashing a oem RUU back to the phone
"RUU_Supersonic_1.47.651.1_Radio_2.05.00.06.10_release_CL195459"
Did you get your phone working? Could you share some of your tricks? Thanks!
brax said:
what i did was followed this guide after flashing a oem RUU back to the phone
"RUU_Supersonic_1.47.651.1_Radio_2.05.00.06.10_release_CL195459"
Click to expand...
Click to collapse
Hi to all!
This morning i wake Up and whole day I can't call and recive calls and message. I search so much on interenet and i try evrything. But no hope.
After i reed that I need to install from ODIN the right AP(software) and CP(modem).
Please give me thah link please ((
At first, tell us, which version of Galaxy S6 you own. I mean F,W8, P etc...
Second, on which android version you have been? Or at least which version you want to use.
rychlin said:
At first, tell us, which version of Galaxy S6 you own. I mean F,W8, P etc...
Second, on which android version you have been? Or at least which version you want to use.
Click to expand...
Click to collapse
Thx a lot my firend for your fast replay
Im using Samsung S6 SM-G920F. And im 6.0.1
The main problem is "Not registered on network" when trying to make a call. I need to fix it. Please help me. :'(
The probel is he show the signal but when I want to call it show "Not registered on network" .
I try everything
- swich sim card to other sim card,
- manual chose network operator, (settings ... - search networks, and when i chose my network it show "Unable to connect, try latter".
- Reinstall the android...
- Wipe data in recovery
And noting is better. it is still the same. Please, please, pleasehelp me
[email protected] said:
The probel is he show the signal but when I want to call it show "Not registered on network" .
I try everything
- swich sim card to other sim card,
- manual chose network operator, (settings ... - search networks, and when i chose my network it show "Unable to connect, try latter".
- Reinstall the android...
- Wipe data in recovery
And noting is better. it is still the same. Please, please, pleasehelp me
Click to expand...
Click to collapse
Your imei is gone?.
Sent from my SM-G925F
Rosli59564 said:
Your imei is gone?.
Sent from my SM-G925F
Click to expand...
Click to collapse
When I go to IMEI information i see it. I see IMEI and IMEI SV. There are the numbers. What to do???
Rosli59564 said:
Your imei is gone?.
Sent from my SM-G925F
Click to expand...
Click to collapse
But when I put on dailer *#0011# and click STACK 1 on the last one where is IMEI Status is NG (i think is no good it is not ok). BUT HOW? How did I lost it? last night i just go t osleap and this morning it doesent work.
Please how to fix it?
Did you buy the phone used? Black listed IMEI?
Sent from my iPhone using Tapatalk
LNJ said:
Did you buy the phone used? Black listed IMEI?
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
I buy used phone, but I work 40 days with no problem. I change the ROM to Slim ROM and work exelent. Last night it was working very well, then I go to sleap, and Now i see it doesent work. I do new sistem on ODin but still notiing.
Sounds to me like someone probably reported it stolen and your IMEI has been blacklisted.
Try a full emergency recovery via Smart Switch.
Sent from my iPhone using Tapatalk
I try but i dont see on the list notting. I go from stock rom to custom rom, and it works for a 40 days very good. And know I can make any calls.
How and what to do next?
[email protected] said:
I try but i dont see on the list notting. I go from stock rom to custom rom, and it works for a 40 days very good. And know I can make any calls.
How and what to do next?
Click to expand...
Click to collapse
hello buddy, have you found a fix for this?
i cant use data on my verizon note 5. i was not able to use it in both UAE and UK. is there anyway i could enable it
Thanks
rkoforever90 said:
i cant use data on my verizon note 5. i was not able to use it in both UAE and UK. is there anyway i could enable it
Thanks
Click to expand...
Click to collapse
You need to go into Settings and then Mobile Network and manually add the APN which is the Access Point Name in order to get it to work. Have you done this?
MrMike2182 said:
You need to go into Settings and then Mobile Network and manually add the APN which is the Access Point Name in order to get it to work. Have you done this?
Click to expand...
Click to collapse
i tried and it didnt work , ill try with an another operator
rkoforever90 said:
i tried and it didnt work , ill try with an another operator
Click to expand...
Click to collapse
Did you put the correct settings in it? It's best to go directly to the provider you're going to used and have them set it up to work for you!
MrMike2182 said:
Did you put the correct settings in it? It's best to go directly to the provider you're going to used and have them set it up to work for you!
Click to expand...
Click to collapse
problem is now solved i went to the service provider directly they manually did the settings
Hi
After installing NXT-L09C432B320 everything is perfect exept sms message is not working
any help please
Try delete caches turn off phone than press VOL+ and POWER when phone boot you will see options to delete cache
Huawei Fan Club Group
www.facebook.com/groups/huaweifanclub
Unfortunately didn't work
Any advice
APN
monos111 said:
Unfortunately didn't work
Any advice
Click to expand...
Click to collapse
Make sure the APN is configured correctly, sometimes has to be done manually.
I think I configured it correctly
Sorry but can you tell me the right way just to make sure of what I did.
monos111 said:
I think I configured it correctly
Sorry but can you tell me the right way just to make sure of what I did.
Click to expand...
Click to collapse
The APN configuration depends on your carrier, it must happen automatically when you put in the SIM card but sometimes when your fiddling with your device it doesn't and you have to do it manually.
Go to settings > more > mobile network > Access point names, take a screen shot and share it here.
Sent from my HUAWEI NXT-L09 using XDA-Developers mobile app
I think it's reading the network correctly
monos111 said:
I think it's reading the network correctly
Click to expand...
Click to collapse
Any Help Please.
monos111 said:
Any Help Please.
Click to expand...
Click to collapse
I don't think it has anything to do with you APN settings, these actually control the data connectivity to the network ( 3G, HSDPA or 4G services ). It's most likely you have the wrong SMS center number. Open the Huawei Messaging app . Open Settings and look around for a setting called "SMS center number" , most likely in the "Advanced" menu ( in my case, but I'm running Nougat Beta which may be different from EMUI 4.0/4.1 ) . There you can set the correct SMS center number , which you can find by googling around or calling you voice provider's support number. After setting the correct SMS center number, restart the phone before testing.
When trying to open the message settings it close the message app and back to home page.
So I can't get in the message settings .
monos111 said:
When trying to open the message settings it close the message app and back to home page.
So I can't get in the message settings .
Click to expand...
Click to collapse
Downgrade to an official firmware, 320 is not officially realeased as far as i know.
which rom do you suggest and is it by dload?
monos111 said:
which rom do you suggest and is it by dload?
Click to expand...
Click to collapse
Which phone do you have and what region?
I've used SKR tool convert my NXT-AL10 to C900B320 and got the message issue then tried C432B320 the Issue steel there
monos111 said:
I've used SKR tool convert my NXT-AL10 to C900B320 and got the message issue then tried C432B320 the Issue steel there
Click to expand...
Click to collapse
Try c432b180 you can find in stock firmware thread and do a factory reset after flashing.
Thank you I'll try it
just through Dload ?
thats only the setting for internet!
monos111 said:
I think it's reading the network correctly
Click to expand...
Click to collapse
Take a look at my screen shot, in my case there are 3 diferent configurations, 1 is exclusive for the MMS, in your screen shot theres only 1 setting and thats is so you have connection to the internet.
Now I would not now how to configure it for your carrier but you might find it in google.
Another possible fix to your problem is to flash the CUST back up that you should have if you backed up your original ROM before upgrading.
I searched the forum for this and maybe I missed something but I can't find help anywhere.
My mother recently passed and we're trying to crack open her LG Velvet. She was very secretive about passwords and such and I can't break passed her finger pattern lock screen. Everything I've found says I can wipe her phone clean and it'll be clear but we need in to access her information and photos, we don't know what details she kept on her phone so we desperately need in. Does anyone know a way we can get passed the lock screen without erasing data? We've tried 55 times all the patterns we think she used but it's so far to no avail. We have T-Mobile, of which I called. They can't help so they sent me to LG and they can't help.
PLEASE SOMEONE HELP!!!
Id u can get an custom recovery installed on that go to /Data/system/ and erase all files with lockscreen name on it and it would remove the pattern
Kratos574 said:
Id u can get an custom recovery installed on that go to /Data/system/ and erase all files with lockscreen name on it and it would remove the pattern
Click to expand...
Click to collapse
Thanks for the reply. Anyway to keep the info on the phone? I don’t mind it going away but I need stuff off the phone.
rdyzzle89 said:
Thanks for the reply. Anyway to keep the info on the phone? I don’t mind it going away but I need stuff off the phone.
Click to expand...
Click to collapse
by the method I told u it doesnt remove any data files
Kratos574 said:
by the method I told u it doesnt remove any data files
Click to expand...
Click to collapse
I’ve not done this in some time, any direction you can point me to get a customer recovery on?
Hey you found a way to get past the code without losing data files? My situation is the exact same except it’s my brother, and it’s sooo frustrating!
Copperheadcross said:
Hey you found a way to get past the code without losing data files? My situation is the exact same except it’s my brother, and it’s sooo frustrating!
Click to expand...
Click to collapse
Hey there, just saw this message. Nope not yet. Terribly frustrating! Her laptop is locked too.
Any luck for you yet?