Related
DISCLOSURE: Not responsible for you being retarded and breaking what doesn't need fixed.
DISCLOSURE 2: Do not use this on the O2x as it has a slightly different partition table.
Here is my step by step for repairing the internalsd Partitions... I don't think I've forgotten anything in this. If anyone knows how to write this into a .zip for flash via CWR it would be great. Credit goes to TeamWhiskey for helping me out when I screwed my partition table up...
WARNING: This can destory your internalSD card partitions. If it's not broke don't fix it!
ALL ENTRIES ARE IN RED
I am not responsible for any damage you do to your phone.
I did this same thing to my phone... I was still able to get into recovery though. You can repair the internal partitions through ADB if you can still get into recovery.
Steps to recreate partitions.
Boot into recovery
from your PC open cmd prompt
change to your ADB directory
run adb shell
mkfs /dev/block/mmcblk0
fdisk -H 1 /dev/block/mmcblk0
if the above fails try fdisk -l /dev/block/mmcblk0
then fdisk -H 1 /dev/block/mmcblk0
once in the fdisk of ../mmcblk0 you might as well delete all the partitions if you believe that they are corrupted
d
1
repeat for partition 2-8
one all of your partitions are gone you now have a blank internal SD and will need to execute the following to restore all the proper partition sizes
Partition 1
n
p
1
First Cylinder start 129
First Cylinder stop 55168
We will repeat this for partitions 2 and 3
Partition 2
n
p
2
Start 55169
Stop 63360
Partition 3
n
p
3
Start 63361
Stop 63616
On to partition 4 which will be extended (this is the last partion you will choose primary or extended)
Partition 4
n
e
4
Start 63617
Stop 975424
Now onto partition 4-8 which are automatically selected as logicall partions (no option is given)
Partition 5
n
Start 63681
Stop 64704
Partition 6
n
Start 64769
Stop 65088
Partition 7
n
Start 65153
Stop 261760
Partition 8
n
Start 261825
Stop 975424
Once you have done this the partitions are ready to be written to the internalSD
I would recommend choosing the command p to verify that all of your start and stop blocks are correct.
From this point you have the option to either quit without saving changes "q" or to write the partition table itself "w". Once you are sure that you have entered all of your partitions correctly you can choose the command w
At this point you have recreated all the partitions on your InternalSD card. If you have a nandroid backup at this point you should be able to restore it without a problem once you copy it over to the internal or external (depending on which CWR you are running).
I didn't have to go through the format portion of the fdisk as I had a nandroid backup which formats all the partitions itself.
If I've forgotten any steps please feel free to comment and include them.
Thanks to TeamWhiskey for helping me resolve this issue when I had it...
Don't forget to click the Thanks button if this helped...
When i get to
Code:
fdisk -h 1 /dev/block/mmcblk0
I get
Code:
unknown option -- hBusyBox v1.16.2androidminimal (2010-03-28 22:34:51 EDT) multi
-call binary.
Did i do anything wrong ?
exPos3D said:
When i get to
Code:
fdisk -h 1 /dev/block/mmcblk0
I get
Code:
unknown option -- hBusyBox v1.16.2androidminimal (2010-03-28 22:34:51 EDT) multi
-call binary.
Did i do anything wrong ?
Click to expand...
Click to collapse
My apologies it is the correct code but should be
Code:
fdisk -H 1 /dev/block/mmcblk0
"I sometimes forget linux commands are case sensitive"
After doing all the steps
When its time to write the tables by executing the "w" command i get this error
Code:
Command (m for help): w
w
The partition table has been altered!
Calling ioctl() to re-read partition table
fdisk: WARNING: rereading partition table failed, kernel still uses old table: D
evice or resource busy
exPos3D said:
After doing all the steps
When its time to write the tables by executing the "w" command i get this error
Code:
Command (m for help): w
w
The partition table has been altered!
Calling ioctl() to re-read partition table
fdisk: WARNING: rereading partition table failed, kernel still uses old table: D
evice or resource busy
Click to expand...
Click to collapse
seems as if I may have forgotten a step but I don't think that I did....
before doing the fdisk command try
Code:
mkfs /dev/block/mmcblk0
if that doesn't work goin into your adb shell and do an
Code:
fdisk -l /dev/block/mmcblk0
and
Code:
fdisk -H 1 /dev/block/mmcblk0
p
and paste the output
It worked thanks but now my sdcard still wont mount for any of my apps, or camera. I can add items to my sd card and install to it, but it still wont mount
I'm not in this area so i do not know where to find files ADB on my computer. If you have time, can you be more detailed instructions to help me ? thank you very much . I waiting for your answer,.
chulun9999 said:
I'm not in this area so i do not know where to find files ADB on my computer. If you have time, can you be more detailed instructions to help me ? thank you very much . I waiting for your answer,.
Click to expand...
Click to collapse
Please use the search function....
http://www.xda-developers.com/android/adb-easy-tutorial/
So I can boot into CWM, but when I try to use ADB it says "Device not found" ...
The phone will boot into the o2x OS, but I get no cell signal. When it boots into the OS, ADB finds it no problem.
Any suggestions?? Does ADB work with all versions of CWM??
Thanks so much for the partition table info!
Try this ... Stock nandroid
Command in windows
Can you post the command you mentioned for linux , to do it in windows . Am using windows 7 . LG update tool screwed my mobile and i have to proceed only with restoring the partition tables .
casper200519 said:
DISCLOSURE: Not responsible for you being retarded and breaking what doesn't need fixed.
DISCLOSURE 2: Do not use this on the O2x as it has a slightly different partition table.
Here is my step by step for repairing the internalsd Partitions... I don't think I've forgotten anything in this. If anyone knows how to write this into a .zip for flash via CWR it would be great. Credit goes to TeamWhiskey for helping me out when I screwed my partition table up...
WARNING: This can destory your internalSD card partitions. If it's not broke don't fix it!
ALL ENTRIES ARE IN RED
I am not responsible for any damage you do to your phone.
I did this same thing to my phone... I was still able to get into recovery though. You can repair the internal partitions through ADB if you can still get into recovery.
Steps to recreate partitions.
Boot into recovery
from your PC open cmd prompt
change to your ADB directory
run adb shell
fdisk -h 1 /dev/block/mmcblk0
once in the fdisk of ../mmcblk0 you might as well delete all the partitions if you believe that they are corrupted
d
1
repeat for partition 2-8
one all of your partitions are gone you now have a blank internal SD and will need to execute the following to restore all the proper partition sizes
Partition 1
n
p
1
First Cylinder start 129
First Cylinder stop 55168
We will repeat this for partitions 2 and 3
Partition 2
n
p
2
Start 55169
Stop 63360
Partition 3
n
p
3
Start 63361
Stop 63616
On to partition 4 which will be extended (this is the last partion you will choose primary or extended)
Partition 4
n
e
4
Start 63617
Stop 975424
Now onto partition 4-8 which are automatically selected as logicall partions (no option is given)
Partition 5
n
Start 63681
Stop 64704
Partition 6
n
Start 64769
Stop 65088
Partition 7
n
Start 65153
Stop 261760
Partition 8
n
Start 261825
Stop 975424
Once you have done this the partitions are ready to be written to the internalSD
I would recommend choosing the command p to verify that all of your start and stop blocks are correct.
From this point you have the option to either quit without saving changes "q" or to write the partition table itself "w". Once you are sure that you have entered all of your partitions correctly you can choose the command w
At this point you have recreated all the partitions on your InternalSD card. If you have a nandroid backup at this point you should be able to restore it without a problem once you copy it over to the internal or external (depending on which CWR you are running).
I didn't have to go through the format portion of the fdisk as I had a nandroid backup which formats all the partitions itself.
If I've forgotten any steps please feel free to comment and include them.
Thanks to TeamWhiskey for helping me resolve this issue when I had it...
Click to expand...
Click to collapse
Can you post the commands to do it from windows ?
bibinkalarikkal said:
Can you post the commands to do it from windows ?
Click to expand...
Click to collapse
Read and go step by step, these are for windows
Sent from my LG-P999 using XDA Premium App
Is there a way to use this app to create one partition just for user app storage? I don't want or need an internal sdcard partition!
Sent from my LG-P999 using xda premium
DUDE!!
Thanks to your instructions and one hour of simple restoration work and my G2X was back in the game. This is for those not faint of heart, but if you've made it far enuff to delete your Internal partitions...Then you could handle these instructions...
PROPZ!!!!
I couldn't do it.When I wrote fdisk -h 1 /dev/block/mmcblk0 to adb shell there was 4 different options.
Usage:fdisk [-ull] [-C CYLINDERS] [-H HEADS] [-S SECTORS] [-b DISK
Change partition table
-u Starts and End are in sectors <instead of cylinders>
-l Show partition table for each DISK, then EXIT
-b 2048 <for certain MO disks>use 2048-byte sectors
-C CYLINDERS Set number of cylinders/heads/sectors
-H HEADS
-S SECTORS
~ #
I don't know what to do.Can you please help me with this?
I tried this because my device was failing while OneClickRecoveryFlash. NVError 0x120000
I'm about to get a g2x, however I have a question..
What causes bad partitioning table? Or messed up partition table?
nitrogen618 said:
I'm about to get a g2x, however I have a question..
What causes bad partitioning table? Or messed up partition table?
Click to expand...
Click to collapse
Flashing a G2X or WIND Optimus 2X which are the same LG-P999 handset with anything for the Optimus 2X (O2X) which is the LG-P990. They use the same internal hardware except for the cell radio modem and use different partition tables so their firmware and ROMs are incompatible. When the LG-P999 is flashed with LG-P990 stuff the LG-P999 will boot as an LG-P990 but there won't be any cell services.
Another reason is an incomplete flashing with LG-P999 firmware.
Core Memory said:
Flashing a G2X or WIND Optimus 2X which are the same LG-P999 handset with anything for the Optimus 2X (O2X) which is the LG-P990. They use the same internal hardware except for the cell radio modem and use different partition tables so their firmware and ROMs are incompatible. When the LG-P999 is flashed with LG-P990 stuff the LG-P999 will boot as an LG-P990 but there won't be any cell services.
Another reason is an incomplete flashing with LG-P999 firmware.
Click to expand...
Click to collapse
Ah, so basically they flashed a p990 rom on a p999.
Another question, when flashing a new rom on cwm you do
-clear data/factory reset
-clear cache partition
-clear dalvik cache
-install rom from sd
Right?
Here's the scenario: say you try out encryption on a ROM, either because your employer makes you or because you want the extra security. What happens when you can root your phone, like we can (easily) with the S3, and you want to flash a different ROM? The problem you will find yourself in very quickly is that you cannot do a successful wipe. You can't format an encrypted /data in CWM or any other recovery. If you cannot format /data, you can't flash a ROM - it fails, because /data is encrypted, and it cannot proceed. It turns out none of the recoveries can format an encrypted /data. You also cannot reverse encryption once you've done it. You're stuck, all because you flipped the switch on encryption.
I found myself in this problem as others have in many other forums (like this one for the GNex) (and another one, more detailed).
I also tried, admittedly somewhat out of desperation, the soft-brick instructions here. That didn't work because Nand Erase All fails. You can flash on top, and luckily you can use your same password to decrypt your /data (which I did) but you're still not going to have a clean ROM. Dirty flashes = lots of problems down the road.
I finally found a simple way to do this and wanted to save anyone else the trouble of digging. You can do it using CWM and adb and a few commands. Credit goes Shawn Webb's blog and utkanos on FreeNode's irc at #cyanogenmod.
Here is how to do this on our Verizon S3:
In CWM, wipe cache
adb shell
mke2fs -t ext4 /dev/block/mmcblk0p15
mount /data
mount /dev/block/mmcblk1p1 /data/media
If adb doesn't work in CWM, reboot recovery. You might need to create /data/media after mounting /data in order to do the last step, which I opted not to do. I hope this saves someone else a few hours of frustration, and I also hope that someday one of our recoveries can handle formatting encrypted data. Until then... I'm just not using encryption, period. There already is a lot of documentation against it, and this is one more reason in my book.
Thanks for this. I fell into the same scenario yesterday but after reading a lot of helpful posts from people like yourself I have managed to solve the issue. Basically I found two ways of doing it, one is as you have suggested and the other is by just replacing the custom recovery with the stock recovery. The SGS3 toolkit available on XDA made the 2nd option just slightly simpler for me and by spending less than 10 mins (excluding time for backups and downloads) the issue was resolved.
Just to share this option to save others from the headache of looking for a solution:
1) Get the toolkit
2) Install drivers as recommended and follow instructions to choose the build, or closest build, for your S3
3) Restore stock recovery with toolkit via ODIN (follow instructions)
4) After rebooting, go into Android and reset to factory settings, this would bring you to the stock recovery and wipe
5) Restore custom recovery with toolkit via ODIN (follow instructions)
6) Restore your system (luckily for me I had a nandroid backup before I encrypted)
Note: I did "lose" my internal sdcard files (pictures/documents). But I backed that up on my external sdcard before starting the process. My sdcard was not encrypted.
kitleon said:
Thanks for this. I fell into the same scenario yesterday but after reading a lot of helpful posts from people like yourself I have managed to solve the issue. Basically I found two ways of doing it, one is as you have suggested and the other is by just replacing the custom recovery with the stock recovery. The SGS3 toolkit available on XDA made the 2nd option just slightly simpler for me and by spending less than 10 mins (excluding time for backups and downloads) the issue was resolved.
Just to share this option to save others from the headache of looking for a solution:
1) Get the toolkit
2) Install drivers as recommended and follow instructions to choose the build, or closest build, for your S3
3) Restore stock recovery with toolkit via ODIN (follow instructions)
4) After rebooting, go into Android and reset to factory settings, this would bring you to the stock recovery and wipe
5) Restore custom recovery with toolkit via ODIN (follow instructions)
6) Restore your system (luckily for me I had a nandroid backup before I encrypted)
Note: I did "lose" my internal sdcard files (pictures/documents). But I backed that up on my external sdcard before starting the process. My sdcard was not encrypted.
Click to expand...
Click to collapse
You just saved my month. Drop me a message if I can get you a beer via paypal for this.
Cheers!
THANKS!
olm3ca said:
Here's the scenario: say you try out encryption on a ROM, either because your employer makes you or because you want the extra security. What happens when you can root your phone, like we can (easily) with the S3, and you want to flash a different ROM? The problem you will find yourself in very quickly is that you cannot do a successful wipe. You can't format an encrypted /data in CWM or any other recovery. If you cannot format /data, you can't flash a ROM - it fails, because /data is encrypted, and it cannot proceed. It turns out none of the recoveries can format an encrypted /data. You also cannot reverse encryption once you've done it. You're stuck, all because you flipped the switch on encryption.
I found myself in this problem as others have in many other forums (like this one for the GNex) (and another one, more detailed).
I also tried, admittedly somewhat out of desperation, the soft-brick instructions here. That didn't work because Nand Erase All fails. You can flash on top, and luckily you can use your same password to decrypt your /data (which I did) but you're still not going to have a clean ROM. Dirty flashes = lots of problems down the road.
I finally found a simple way to do this and wanted to save anyone else the trouble of digging. You can do it using CWM and adb and a few commands. Credit goes Shawn Webb's blog and utkanos on FreeNode's irc at #cyanogenmod.
Here is how to do this on our Verizon S3:
In CWM, wipe cache
adb shell
mke2fs -t ext4 /dev/block/mmcblk0p15
mount /data
mount /dev/block/mmcblk1p1 /data/media
If adb doesn't work in CWM, reboot recovery. You might need to create /data/media after mounting /data in order to do the last step, which I opted not to do. I hope this saves someone else a few hours of frustration, and I also hope that someday one of our recoveries can handle formatting encrypted data. Until then... I'm just not using encryption, period. There already is a lot of documentation against it, and this is one more reason in my book.
Click to expand...
Click to collapse
Just wanted to say thanks very much for this. I'd tried the method of reloading the stock ROM as described by a previous poster, but this way worked.
I did run into a small issue I was wondering if you could shed some light on. When I entered "mount /data", I got the following:
Code:
~ # mount /data
mount: mounting /dev/block/mmcblk0p37 on /data failed: Invalid argument
I bullied ahead and entered the last line "mount /dev/block/mmcblk1p1 /data/media" and got this:
Code:
~ # mount /dev/block/mmcblk1p1 /data/media
mount: mounting /dev/block/mmcblk1p1 on /data/media failed: No such file or directory
However after doing this, I was able to perform a complete wipe of /data using CWM and load a new ROM without issue.
I'd curious to know what might be causing these Invald argument responses.
My Device: HTC One (GSM)
Thanks again! :laugh:
olm3ca said:
Here is how to do this on our Verizon S3:
In CWM, wipe cache
adb shell
mke2fs -t ext4 /dev/block/mmcblk0p15
mount /data
mount /dev/block/mmcblk1p1 /data/media
If adb doesn't work in CWM, reboot recovery. You might need to create /data/media after mounting /data in order to do the last step, which I opted not to do. I hope this saves someone else a few hours of frustration, and I also hope that someday one of our recoveries can handle formatting encrypted data. Until then... I'm just not using encryption, period. There already is a lot of documentation against it, and this is one more reason in my book.
Click to expand...
Click to collapse
I'm trying to follow your instructions but fail at finding out my mount points.
Sorry for the noob question, but who do I find out what the mount points of internal and external SD card are on my device (Samsung Galaxy S4 Mini International 4G)? I found this post
stackoverflow. /questions/6824463/how-to-get-all-the-mount-point-information-for-android-device
which seems to include the answer but I don't know what tool / software they use. I'm no programmer.
My phone is encrypted and doesn't turn on, it doesn't accept my password saying it's wrong, though I know it's correct. OS is Cyanogenmod 10.1 stable. Booting into CWM v6.0.3.7 is possible though.
I appreciate everyone's help.
Stephan
I previously ran LolliGPE but was long overdue for an update. I downloaded the latest version and copied the image to my phone and flashed the ROM. I decided to go try a dirty install first to see if I could keep everything I had, since I had already been running a previous version and after reviewing the changelog did not see anything recommending to wipe clean. After installing successfully, Android asked me to enter my password to decrypt my data (I don't recall ever encrypting my data?), and so I did. It then told me that my password was right, but the data was corrupt, and presented me a button to reset my phone. The button redirected me to recovery and automatically attempted to wipe /data and then re-mount it, but the wipe failed. I rebooted again with the same issue, same failed attempt to wipe. I went to install the zip again, and this time do a full wipe, but it was unable to mount my phone's storage nor my SD card. I am not able to mount either at all now.
What's the best course of action? I'd like to retain as much as I can and avoid wiping all of the internal storage clean. Is there a simpler fix to this or am I doomed?
HBOOT: 3.19.0.0000
RADIO: 1.09.20.0926
OS: 3.28.605.4
EDIT: For anyone else having a problem like this that at least wants to get their data back, here's what you should do (I assume you know how to work with Linux!):
Make sure you have the latest version of TWRP and ADB.
Boot the phone into recovery mode and connect the phone to your computer via USB
Run "ls -al /dev/block/platform/msm_sdcc.1/by-name" and check the output. Make a note of the partition marked "userdata" - for me, it was /dev/block/mmcblk0p48.
Either: simply use adb pull to copy this file to your computer (this will require about 26 gigs of space), or attempt to mount the file. To use adb pull, execute "adb pull /dev/block/<ID> ./data" (ID being what you marked down). Your data partition will be copied to /data. To mount, use "mount -t ext4 /dev/block/<ID> /userdata". Whatever's left of your data will be on your phone's new /userdata folder.
Use ADB to pull what files you want from /userdata. If you pulled the partition, skip this step.
If you copied the files you wanted over, you're done. If you pulled the entire partition, you're going to want to try and mount it. On Windows, there are various tools to mount Linux partitions, a quick Google will find some good ones. However, if the data is corrupt, it will not work. I recommend attempting to repair the partition on linux, with the command "e2fsck -f -y /path/to/data", replacing the path to your data file as necessary. Once done, run "mount -t ext4 /path/to/data /mnt/data", replacing the paths as necessary.
Once mounted, you can access your data wherever it was mounted. If e2fsck appeared to fix many errors, chances are most of your data will be in the lost+found folder, and you'll need to sort through this yourself. If you're lucky, then your data will be intact and readily usable. Internal SD card data is located at ./media/0.
To fix the partitions and get Android back up and running, you need to install the latest firmware, format your data in TWRP, factory reset, and then flash a ROM again. Here's what I did to do that, without an SD card. If you have an SD card, simply copy your ROM zip to the SD card and skip the final steps:
Make sure you have the latest version of TWRP and ADB, and download the latest copy of the firmware (check the development forum here).
Boot the phone (doesn't matter to what) and run adb reboot bootloader. When your phone reboots, double-check by running fastboot reboot-bootloader.
Put your phone in RUU mode with fastboot oem rebootRUU. The phone will restart and the HTC logo will come up.
Wait a couple seconds, then run fastboot flash zip firmware.zip, where firmware.zip is the firmware you want to flash.
The first time you do this, it will fail saying something like "FAILED (remote: 90 hboot pre-update! please flush image again immediately)". Ignore this, run the last command again: fastboot flash zip firmware.zip
The progress bar will appear and begin filling. Wait until fastboot is finished flashig it (the progress bar may not fill completely), wait an extra 5 seconds or so, and then do fastboot reboot.
The phone will reboot. Android will still be messed up, but you can verify the partitions are in working order by checking adb shell cat /proc/emmc.
Once you know the partitions are working, get back into TWRP/recovery: adb reboot recovery
Format /data and wipe /cache, /data, dalvik/art cache, etc (factory reset). You will lose the contents of your internal storage and everything else.
If you don't have the ROM zip on an sd card, make sure the zip is in the same directory as adb and run adb push rom.zip /sdcard/rom.zip, where rom.zip is the ROM. You can also copy it to the external sd by swapping /sdcard/rom.zip with /external_storage/rom.zip.
Once copied, reboot into recovery and flash the zip. Back to normal!
Update:
It's a firmware problem. Apparently there was a new firmware update that the ROM uses that I don't have. mmcblk0p42 was changed to "vzw_logger" (which I don't have), making mmcblk0p49 userdata instead of previously mmcblk0p48. The data partition it expects to be /data is /cache. Got this information by comparing 'cat /proc/emmc' with information of the latest version I found here.
Is there a way to fix this that allows me to preserve the contents of my internal storage (/sdcard)? Can I just flash an older version of the ROM to backup my data?
Klayderpus said:
Update:
It's a firmware problem. Apparently there was a new firmware update that the ROM uses that I don't have. mmcblk0p42 was changed to "vzw_logger" (which I don't have), making mmcblk0p49 userdata instead of previously mmcblk0p48. The data partition it expects to be /data is /cache. Got this information by comparing 'cat /proc/emmc' with information of the latest version I found here.
Is there a way to fix this that allows me to preserve the contents of my internal storage (/sdcard)? Can I just flash an older version of the ROM to backup my data?
Click to expand...
Click to collapse
I posted a warning about this change in the general section early on. For you to have the partition changes means you are on the newer firmware which doesn't match what you posted above for os. You very likely at this point have nothing left to salvage. Are you on the latest twrp?
dottat said:
I posted a warning about this change in the general section early on. For you to have the partition changes means you are on the newer firmware which doesn't match what you posted above for os. You very likely at this point have nothing left to salvage. Are you on the latest twrp?
Click to expand...
Click to collapse
I am on the latest TWRP, yes. Since this post, I've actually been making good progress in getting the data partition back, or so I think. I've been using dd to copy /dev/block/mntblk0p48 to an image file, but got stuck when I reached the FAT32 limit, so I re-formatted my SD card, except now it's read-only.
Klayderpus said:
I am on the latest TWRP, yes. Since this post, I've actually been making good progress in getting the data partition back, or so I think. I've been using dd to copy /dev/block/mntblk0p48 to an image file, but got stuck when I reached the FAT32 limit, so I re-formatted my SD card, except now it's read-only.
Click to expand...
Click to collapse
If you Dd the entire data partition it's gonna be almost 25 gigs. If you can't mount data in twrp and find anything usable when browsing via adb in twrp there's probably not anything usable in there.
dottat said:
If you Dd the entire data partition it's gonna be almost 25 gigs. If you can't mount data in twrp and find anything usable when browsing via adb in twrp there's probably not anything usable in there.
Click to expand...
Click to collapse
I did a DD before while in ADB and it only got to about 1.3 gigs, but after running the image through e2fsck I actually found some images and downloads. I think there's usable stuff in there and I'd like to at least try to get it. There's family pictures and stuff on there that have some value to me. My SD card is 32 gigs so I could probably do it if anything for the hell of it.
Do you happen to know how I can get the SD card mounted? mount -o rw,remount /dev/block/mmcblk1p1 [some dir] is what I've been trying, but I've been getting either Read only filesystem or Invalid argument.
I might be a little crazy
Klayderpus said:
I did a DD before while in ADB and it only got to about 1.3 gigs, but after running the image through e2fsck I actually found some images and downloads. I think there's usable stuff in there and I'd like to at least try to get it. There's family pictures and stuff on there that have some value to me. My SD card is 32 gigs so I could probably do it if anything for the hell of it.
Do you happen to know how I can get the SD card mounted? mount -o rw,remount /dev/block/mmcblk1p1 [some dir] is what I've been trying, but I've been getting either Read only filesystem or Invalid argument.
I might be a little crazy
Click to expand...
Click to collapse
Its already mounted.. Just boot into TWRP while connected to your PC. Open cmd prompt in your adb directory.
adb shell
cd sdcard
ls
See if your internal SD card contents are listed.
dottat said:
Its already mounted.. Just boot into TWRP while connected to your PC. Open cmd prompt in your adb directory.
adb shell
cd sdcard
ls
See if your internal SD card contents are listed.
Click to expand...
Click to collapse
TWRP lists the internal SD card as being size 0 under Mount -> Select Storage and /sdcard is empty. I re-formatted my external SD card to make a full size image but that's what wasn't mounting.
Klayderpus said:
TWRP lists the internal SD card as being size 0 under Mount -> Select Storage and /sdcard is empty. I re-formatted my external SD card to make a full size image but that's what wasn't mounting.
Click to expand...
Click to collapse
Did you try the repair option for /data listed under wipe in TWRP?
dottat said:
Did you try the repair option for /data listed under wipe in TWRP?
Click to expand...
Click to collapse
Doesn't work. There's a couple of messages about not being able to mount /data and then:
Code:
Repairing Data using e2fsck...
E:Unable to repair '/data'.
E:Error repairing file system.
Klayderpus said:
Doesn't work. There's a couple of messages about not being able to mount /data and then:
Code:
Repairing Data using e2fsck...
E:Unable to repair '/data'.
E:Error repairing file system.
Click to expand...
Click to collapse
try this
adb shell
mount -t ext4 /dev/block/mmcblk0p49 /userdata
df
show me the output of df...
and if to be sure of which firmware you are on.. reboot recovery... and do the following....
adb shell
mount -t ext4 /dev/block/mmcblk0p48 /userdata
df
and show me that DF
I got all of my data back successfully. I'm updating the OP with the steps I did to get it back.
What's the next step? Change firmware? I have a local copy of what I needed from the phone, so anything's game now.
edit: /dev/block/mmcblk0p48 for me is userdata, 49 does not exist. Both mounts fail.
Code:
df
Filesystem 1K-blocks Used Available Use% Mounted on
tmpfs 933044 24 933020 0% /dev
tmpfs 933044 20 933024 0% /tmp
/dev/block/mmcblk0p47 1030828 16464 1014364 2% /cache
/dev/block/mmcblk1p1 30647232 12 29090436 0% /external_sd
/dev/block/mmcblk1p1 30647232 12 29090436 0% /and-sec
Klayderpus said:
I got all of my data back successfully. I'm updating the OP with the steps I did to get it back.
What's the next step? Change firmware? I have a local copy of what I needed from the phone, so anything's game now.
edit: /dev/block/mmcblk0p48 for me is userdata, 49 does not exist. Both mounts fail.
Code:
df
Filesystem 1K-blocks Used Available Use% Mounted on
tmpfs 933044 24 933020 0% /dev
tmpfs 933044 20 933024 0% /tmp
/dev/block/mmcblk0p47 1030828 16464 1014364 2% /cache
/dev/block/mmcblk1p1 30647232 12 29090436 0% /external_sd
/dev/block/mmcblk1p1 30647232 12 29090436 0% /and-sec
Click to expand...
Click to collapse
I would say update firmware. Since you confirmed blk48 as user data I know you don't have lollipop firmware.
I posted a firmware zip that contains the newest twrp which is compatible with lollipop in tigerstowns firmware thread. You can use that to update.
Then wipe and reinstall whatever Rom you want to use.
I fixed it this morning by updating firmware and will update the OP with the rest of the steps for the Googlers. Thanks again.
Klayderpus said:
EDIT: For anyone else having a problem like this that at least wants to get their data back, here's what you should do (I assume you know how to work with Linux!):
Make sure you have the latest version of TWRP and ADB.
Boot the phone into recovery mode and connect the phone to your computer via USB
Run "ls -al /dev/block/platform/msm_sdcc.1/by-name" and check the output. Make a note of the partition marked "userdata" - for me, it was /dev/block/mmcblk0p48.
Either: simply use adb pull to copy this file to your computer (this will require about 26 gigs of space), or attempt to mount the file. To use adb pull, execute "adb pull /dev/block/<ID> ./data" (ID being what you marked down). Your data partition will be copied to /data. To mount, use "mount -t ext4 /dev/block/<ID> /userdata". Whatever's left of your data will be on your phone's new /userdata folder.
Use ADB to pull what files you want from /userdata. If you pulled the partition, skip this step.
If you copied the files you wanted over, you're done. If you pulled the entire partition, you're going to want to try and mount it. On Windows, there are various tools to mount Linux partitions, a quick Google will find some good ones. However, if the data is corrupt, it will not work. I recommend attempting to repair the partition on linux, with the command "e2fsck -f -y /path/to/data", replacing the path to your data file as necessary. Once done, run "mount -t ext4 /path/to/data /mnt/data", replacing the paths as necessary.
Once mounted, you can access your data wherever it was mounted. If e2fsck appeared to fix many errors, chances are most of your data will be in the lost+found folder, and you'll need to sort through this yourself. If you're lucky, then your data will be intact and readily usable. Internal SD card data is located at ./media/0.
[/LIST]
Click to expand...
Click to collapse
I have a laptop running Ubuntu: where do I run the "ls -al /dev/block..." command? As in what folder do I need to be in? The phone only appears in an mtp capacity...
EDIT: I figured that out but now I am stuck at "adb pull /dev/block/<ID> ./data". My ID was mmcblk0p28 but the command returns "Bash: mmcblk0p28: no such file or directory exists"
EDIT 2: Got that command to work but the file is too large to write (My disk is FAT32 ). So I then tried the mount command but again got "no such file or directory exists".
Same Issue "Decryption Unsuccessful"
I was trying to apply the OTA update for 5.1 on my M8 converted to GPE 5.01, but had to update to the stock recovery, and found myself in the same situation with the "Decryption Unsuccessful" message.
Following Klayderpus' steps to recover, but I'm running into a few issues:
1) Windows not Ubuntu so some (many) of the commands do not apply.
2) The device is not responding to adb, although it was prior to the "upgrade". Fastboot is working.
3) TWRP was not on the device, in fact I never could get to the recovery after trying to install the stock recovery when I converted to GPE 5.01 many months ago
I have a fresh nandroid backup, so I am just trying to get the device running. Being without the phone is causing me great pain....
I upgraded the firmware to 4.16 and did the factory reset from the stock 4.16 recovery. The phone boots back to the "Decryption Unsuccessful" message.
I am not sure, but I think the next step for me to try is to install the GPE ROM from graffixnyc from the microSD card (need to find/buy that little SD adaptor)
Any help would be greatly appreciated!!
========================
Update;
Recovery does not see the SD card , so I won't be able to install from there.
I'll try flashing TWRP recover to see if that will show the contents of the external card
========================
Update 2:
TWRP does see the external card, but the install failed as it is unable to mount /data and /storage.
I'm out of ideas....HELP!!
========================
Update 3
I noticed the "factory reset" in HBOOT and thought I'd try that instead of the "Wipe" in TWRP, but only made things worse.
Now the phone comes up to the "Decryption Unsuccessful" where I can then take the reset to get it into TWRP recover
TWRP comes up directly into a screen where it's "Running OpenRecovery Script" and then reboots.
I'm going to quit now, as I am only making matters worse.....
========================
Update 4
I got TWRP to quit whatever it was doing.
Now, In TWRP > Wipe > Advanced Wipe, I cannot wipe or repair the Data partition. I see a message "Could not mount /data unable to find crypto footer". Trying to wipe the Davlik Cache fails, "Unable to mount /data, " Unable to mount storage".
========================
version-bootloader: 3.19.0.0000
version-baseband: 1.25.214500021.06G
version-main: 4.16.401.10
modelid: 0P6B12000
cidnum: 11111111
========================
I've bricked the phone and it looks permanent.
I found another thread where everyone was solving this issue running this command "mke2fs -T ext4 /dev/block/mmcblk0p8" in TWRP. I failed to notice that it was not an M8 device thread. The phone won't boot at all, and windows sees it as a usb drive.
Haste makes waste
Do you still have fastboot?
Check out the RUU collection here and grab what apllies to your device:
http://forum.xda-developers.com/ver...zw-m8-master-ruu-firmware-collection-t2946473
Make sure you use the HTC fastboot.exe from post 3
highplains914drifter said:
I was trying to apply the OTA update for 5.1 on my M8 converted to GPE 5.01, but had to update to the stock recovery, and found myself in the same situation with the "Decryption Unsuccessful" message.
Following Klayderpus' steps to recover, but I'm running into a few issues:
1) Windows not Ubuntu so some (many) of the commands do not apply.
2) The device is not responding to adb, although it was prior to the "upgrade". Fastboot is working.
3) TWRP was not on the device, in fact I never could get to the recovery after trying to install the stock recovery when I converted to GPE 5.01 many months ago
I have a fresh nandroid backup, so I am just trying to get the device running. Being without the phone is causing me great pain....
I upgraded the firmware to 4.16 and did the factory reset from the stock 4.16 recovery. The phone boots back to the "Decryption Unsuccessful" message.
I am not sure, but I think the next step for me to try is to install the GPE ROM from graffixnyc from the microSD card (need to find/buy that little SD adaptor)
Any help would be greatly appreciated!!
========================
Update;
Recovery does not see the SD card , so I won't be able to install from there.
I'll try flashing TWRP recover to see if that will show the contents of the external card
========================
Update 2:
TWRP does see the external card, but the install failed as it is unable to mount /data and /storage.
I'm out of ideas....HELP!!
========================
Update 3
I noticed the "factory reset" in HBOOT and thought I'd try that instead of the "Wipe" in TWRP, but only made things worse.
Now the phone comes up to the "Decryption Unsuccessful" where I can then take the reset to get it into TWRP recover
TWRP comes up directly into a screen where it's "Running OpenRecovery Script" and then reboots.
I'm going to quit now, as I am only making matters worse.....
========================
Update 4
I got TWRP to quit whatever it was doing.
Now, In TWRP > Wipe > Advanced Wipe, I cannot wipe or repair the Data partition. I see a message "Could not mount /data unable to find crypto footer". Trying to wipe the Davlik Cache fails, "Unable to mount /data, " Unable to mount storage".
========================
version-bootloader: 3.19.0.0000
version-baseband: 1.25.214500021.06G
version-main: 4.16.401.10
modelid: 0P6B12000
cidnum: 11111111
========================
I've bricked the phone and it looks permanent.
I found another thread where everyone was solving this issue running this command "mke2fs -T ext4 /dev/block/mmcblk0p8" in TWRP. I failed to notice that it was not an M8 device thread. The phone won't boot at all, and windows sees it as a usb drive.
Haste makes waste
Click to expand...
Click to collapse
If you have fastboot do the following commands
Fastboot oem task 28
Fastboot oem task 29
Then try to flash your rom or ruu.
dottat said:
If you have fastboot do the following commands
Fastboot oem task 28
Fastboot oem task 29
Then try to flash your rom or ruu.
Click to expand...
Click to collapse
No Fastboot, nothing. Device was charged, but now acts as if the battery is dead. the Power button does nothing even after a long press.
Bad day...
Klayderpus said:
I previously ran LolliGPE but was long overdue for an update. I downloaded the latest version and copied the image to my phone and flashed the ROM. I decided to go try a dirty install first to see if I could keep everything I had, since I had already been running a previous version and after reviewing the changelog did not see anything recommending to wipe clean. After installing successfully, Android asked me to enter my password to decrypt my data (I don't recall ever encrypting my data?), and so I did. It then told me that my password was right, but the data was corrupt, and presented me a button to reset my phone. The button redirected me to recovery and automatically attempted to wipe /data and then re-mount it, but the wipe failed. I rebooted again with the same issue, same failed attempt to wipe. I went to install the zip again, and this time do a full wipe, but it was unable to mount my phone's storage nor my SD card. I am not able to mount either at all now.
What's the best course of action? I'd like to retain as much as I can and avoid wiping all of the internal storage clean. Is there a simpler fix to this or am I doomed?
HBOOT: 3.19.0.0000
RADIO: 1.09.20.0926
OS: 3.28.605.4
EDIT: For anyone else having a problem like this that at least wants to get their data back, here's what you should do (I assume you know how to work with Linux!):
Make sure you have the latest version of TWRP and ADB.
Boot the phone into recovery mode and connect the phone to your computer via USB
Run "ls -al /dev/block/platform/msm_sdcc.1/by-name" and check the output. Make a note of the partition marked "userdata" - for me, it was /dev/block/mmcblk0p48.
Either: simply use adb pull to copy this file to your computer (this will require about 26 gigs of space), or attempt to mount the file. To use adb pull, execute "adb pull /dev/block/<ID> ./data" (ID being what you marked down). Your data partition will be copied to /data. To mount, use "mount -t ext4 /dev/block/<ID> /userdata". Whatever's left of your data will be on your phone's new /userdata folder.
Use ADB to pull what files you want from /userdata. If you pulled the partition, skip this step.
If you copied the files you wanted over, you're done. If you pulled the entire partition, you're going to want to try and mount it. On Windows, there are various tools to mount Linux partitions, a quick Google will find some good ones. However, if the data is corrupt, it will not work. I recommend attempting to repair the partition on linux, with the command "e2fsck -f -y /path/to/data", replacing the path to your data file as necessary. Once done, run "mount -t ext4 /path/to/data /mnt/data", replacing the paths as necessary.
Once mounted, you can access your data wherever it was mounted. If e2fsck appeared to fix many errors, chances are most of your data will be in the lost+found folder, and you'll need to sort through this yourself. If you're lucky, then your data will be intact and readily usable. Internal SD card data is located at ./media/0.
To fix the partitions and get Android back up and running, you need to install the latest firmware, format your data in TWRP, factory reset, and then flash a ROM again. Here's what I did to do that, without an SD card. If you have an SD card, simply copy your ROM zip to the SD card and skip the final steps:
Make sure you have the latest version of TWRP and ADB, and download the latest copy of the firmware (check the development forum here).
Boot the phone (doesn't matter to what) and run adb reboot bootloader. When your phone reboots, double-check by running fastboot reboot-bootloader.
Put your phone in RUU mode with fastboot oem rebootRUU. The phone will restart and the HTC logo will come up.
Wait a couple seconds, then run fastboot flash zip firmware.zip, where firmware.zip is the firmware you want to flash.
The first time you do this, it will fail saying something like "FAILED (remote: 90 hboot pre-update! please flush image again immediately)". Ignore this, run the last command again: fastboot flash zip firmware.zip
The progress bar will appear and begin filling. Wait until fastboot is finished flashig it (the progress bar may not fill completely), wait an extra 5 seconds or so, and then do fastboot reboot.
The phone will reboot. Android will still be messed up, but you can verify the partitions are in working order by checking adb shell cat /proc/emmc.
Once you know the partitions are working, get back into TWRP/recovery: adb reboot recovery
Format /data and wipe /cache, /data, dalvik/art cache, etc (factory reset). You will lose the contents of your internal storage and everything else.
If you don't have the ROM zip on an sd card, make sure the zip is in the same directory as adb and run adb push rom.zip /sdcard/rom.zip, where rom.zip is the ROM. You can also copy it to the external sd by swapping /sdcard/rom.zip with /external_storage/rom.zip.
Once copied, reboot into recovery and flash the zip. Back to normal!
Click to expand...
Click to collapse
Hey
I have a HTC one m7 verizon & same problem storage decryption failed. See my case here in below post. And please tell me if anything possible. Please......
http://forum.xda-developers.com/verizon-htc-one/help/storage-encryped-htc-one-m7-vzw-s-t3279869
This guide was written for the Huawei y6 with a gpt partition table, mounts that use partition names not numbers and the userdata partition is the last one on disk however with a little adaption this should work for most gpt devices.
If you are unsure if your system uses partition names for the mount system look in /fstab."hardware" to see if your devices are labelled in the following manner. "/dev/block/bootdevice/by-name/system".
If the fstab file does not exist all is not lost look in your root directory at the .rc files for the command mounting system.
If you are unsure ask in the thread before doing anything. Better to ask than be stuck with a brick.
This guide covers modification to only system and userdata partitions but if you use great care the basics covered here will allow for modification to other partitions as long as you understand the risk and know that backups are your friend.
If you are unable to follow instructions and end up with a bricked device that is your own fault and attempts to blame me will be laughed at.
I obtained the attached parted binary from here
So you have flashed a custom ROM and without all the OEM bloatware you now have some unused free space in your system partition just sitting there gathering dust.
You are stuck with this space... Wrong.
You can repartition your device with a little paitence, time and work.
Read along if you are curious about how to get the space you deserve.
Prerequisites:
Free space (Duh).
The ability to follow instructions and to read ALL steps before you start so you know what your plan is.
An unlocked bootloader which you already have if you flashed a custom ROM.
A custom recovery (twrp preferred).
Parted binary (see attachment at the bottom of this post).
A computer with adb installed and working (there are many guides out there if you don't have it, Google is your friend).
A calculator (well I'm sure your computer has one but just so you know).
Some knowledge using terminal commands.
Risk of Bricking your device:
Low if you backup and can double check typing and calulations.
High if you can't do one of the above.
Because parted does not allow resizing of ext4 partitions you must delete partitions you want to change then recreate them.
All steps must be performed while in recovery because you are going to have to unmount any partition before you can change it.
Step 1:
Boot into recovery and make a backup. You MUST do this otherwise you will have nothing to restore.
Step 2:
Plug your device into your computer.
Copy the parted binary into your working directory on your PC.
Open your Command Prompt (Windows) or Terminal (Linux) and navigate to where adb is installed and you also put parted, or if you have adb in your PATH just go to where parted is.
Run
Code:
~ # adb devices
to ensure your device is present.
Run
Code:
~ # adb root
to get root priviliges.
Run
Code:
~ # adb push parted /sbin/parted
/sbin is in your devices PATH so you don't have to worry about typing /parted.
Run
Code:
~ # adb shell
Run
Code:
~ # chmod 755 /sbin/parted
If you get an error about a read only file system run
Code:
mount -o remount,rw /
then try again.
Step 3: Now you need to do some homework to find your sector size, sector count and how much free space you have available.
DO NOT shrink your filesystem to smaller than you need to operate. I always add at LEAST 50 mb to the used space however I recommend you think for the future, are you planning on restoring to stock?, are you planning on flashing OpenGAPPS?, are you planning on moving third party apps into the system?, are you planning on adding media or custom boot animations to the system?
So in the case below I would not make the partition any smaller than 800 MB.
Code:
~ # df
Filesystem Size Used Free Blksize
/system 1.2G 748.5M 441.8M 4096
/data 5.2G 3.5G 1.6G 4096
/cache 147.2M 4.7M 142.5M 4096
Now issue the following command to get your disks sector size in bytes remember to note this down.
Code:
~ # blockdev --getss /dev/block/mmcblk0
512
Time to use parted.
Issue the following commands to get some info on your current partitions.
"unit s" tells parted to show sectors instead of blocks, bytes etc.
Code:
~ # parted /dev/block/mmcblk0
(parted) unit s
(parted) print
Number Start End Size File system Name Flags
22 876562s 1191132s 314571s ext4 cache
23 1191133s 3990839s 2799707s ext4 system
24 3990840s 15269854s 11279015s ext4 userdata
Remember to not the partition number as you will need it later.
Remember to note your partition name with exact case, if you changed "system" to "System" you will have problems.
Also note the start sector of your system partition for the later steps.
Also note the end sector number for your userdata partition for the later steps.
Now get your calulator ready.
Some things to keep in mind here are that the number of sectors times sector size is the size of your partition in bytes and your starting sector must be 1 after the end of the previous partition.
So the following equation will give you the numbers you need.
Desired size in MB * 1024 * 1024 / Sector Size = Number of sectors
Starting sector + Number of sectors - 1 = Last Sector
If you want a 1.1 Gb partition, you have 512 byte sectors and the starting sector is 1191133 you would then use the following equation.
1100 * 1024 * 1024 / 512 = 2252800
1191133 + 2252800 - 1 = 3443932
Step 4:
Now using the info you have gathered you can change your partitions.
So I would issue the following commands to delete, create and name the system partition with the size I want.
Code:
(parted) rm 23
(parted) mkpart 23 ext4 1191133 3443932
(parted) name 23 system
Now to resize the data partition.
You need to start with the first available sector after the end of system and end with the last available sector noted earlier.
Code:
(parted) rm 24
(parted) mkpart 24 ext4 3443933 15269854
(parted) name 24 userdata
Now that your partitions are all done you can exit parted with the following.
Code:
(parted) quit
Step 5:
Now restore the backup you made earlier.
If you get an error restoring which usually only happens if you have altered partition numbers just reboot back into recovery and restore then so the kernel gets to update its own info.
Reboot.
Congratulations you now have repartitioned your device.
Don't forget to thank this post if you are grateful.
Is there anything diferent to do about moderm mmcblkop14(/firmware)? I want to reduce it to 100 mb but i noticed its blocksize it's different from the others (others =4096, firmware=16384). I saw in your pictures you reduce it, so i will try it to do that. I have a nandroid so i hope this try works.
OK, i should probably been the first idiot to bricked his phone by reading a tutorial.
I need some help. I was trying to make this extra space and i have a few problems during the process.
First of all, in my case i have a partition 23 called cust, exactly the same in size with the cache. So i started with the cache calculating and then the other 3( 23 cust, 24 system, 25 userdata). For that moment i already made my nandroid, buy for some stupid reason I saved to my pc.
My problems came when i began with step 4. When i tried to put the cache it told me that it can't do it because it was in use. So i twrp y put on mount and desmounted that partition and then i could keep going. Same thing happened with Data partition, i did the same.
Finally, i did it all the tutorial, just needed to restore as it said in step 5 because i didn't have it in my phone. So i tried with adb push but nothing and i couldn't mount again those partition with twrp. Then, in a desperate move, i tried to reflash my cm rom, so i did that. And later, it bootloop with te huawei logo and i can´t flash a rom o restore my nandroid. It doesn't read a sdcard.
And now, when i see the script in twrp (sorry i don't know how is the name, i talking about the center botton in twrp) it appears in red "unable to mont '/data', '/system', '/cache'.
I don't know what to do, really, i need a hand.
beatLeo said:
OK, i should probably been the first idiot to bricked his phone by reading a tutorial.
I need some help. I was trying to make this extra space and i have a few problems during the process.
First of all, in my case i have a partition 23 called cust, exactly the same in size with the cache. So i started with the cache calculating and then the other 3( 23 cust, 24 system, 25 userdata). For that moment i already made my nandroid, buy for some stupid reason I saved to my pc.
My problems came when i began with step 4. When i tried to put the cache it told me that it can't do it because it was in use. So i twrp y put on mount and desmounted that partition and then i could keep going. Same thing happened with Data partition, i did the same.
Finally, i did it all the tutorial, just needed to restore as it said in step 5 because i didn't have it in my phone. So i tried with adb push but nothing and i couldn't mount again those partition with twrp. Then, in a desperate move, i tried to reflash my cm rom, so i did that. And later, it bootloop with te huawei logo and i can�´t flash a rom o restore my nandroid. It doesn't read a sdcard.
And now, when i see the script in twrp (sorry i don't know how is the name, i talking about the center botton in twrp) it appears in red "unable to mont '/data', '/system', '/cache'.
I don't know what to do, really, i need a hand.
Click to expand...
Click to collapse
Ok this is difficult because of your wording but it sounds like data, system and cache no longer exist.
Is your device the y6?
Do you have adb access?
Did you finish recreating the partitions?
Did you manage to name them if so?
Are you able to use recovery?
If you have adb can use please issue the following code, if you don't have adb can you please use twrp, advanced, terminal command to issue it.
Code:
ls /dev/block/bootdevice/by-name/
and let me know if it shows your cache, userdata and system.
DestructoSphere said:
Ok this is difficult because of your wording but it sounds like data, system and cache no longer exist.
Is your device the y6?
Do you have adb access?
Did you finish recreating the partitions?
Did you manage to name them if so?
Are you able to use recovery?
If you have adb can use please issue the following code, if you don't have adb can you please use twrp, advanced, terminal command to issue it.
Code:
ls /dev/block/bootdevice/by-name/
and let me know if it shows your cache, userdata and system.
Click to expand...
Click to collapse
- Yes, my device is Y6 (SCL-L03).
- Seems that i don't have access to adb, because in cmd show me "offline" device.
-Yes, i fineshed with that, but couldn't do the restore of backup.
- I did all step 4.
- Yes, i'm using twrp.
I put the code with twrp... and here it says not found.
Any ideas? I hope you could help me.
beatLeo said:
Ok this is difficult because of your wording but it sounds like data, system and cache no longer exist.
Is your device the y6?
Do you have adb access?
Did you finish recreating the partitions?
Did you manage to name them if so?
Are you able to use recovery?
If you have adb can use please issue the following code, if you don't have adb can you please use twrp, advanced, terminal command to issue it.
- Yes, my device is Y6 (SCL-L03).
- Seems that i don't have access to adb, because in cmd show me "offline" device.
-Yes, i fineshed with that, but couldn't do the restore of backup.
- I did all step 4.
- Yes, i'm using twrp.
I put the code with twrp... and here it says not found.
Any ideas? I hope you could help me.
Click to expand...
Click to collapse
You need to put a space between ls and the /
DestructoSphere said:
You need to put a space between ls and the /
Click to expand...
Click to collapse
ups, ok, i did that and i see all the partitions including cache, cust, system and userdata. Please, what is next?
beatLeo said:
ups, ok, i did that and i see all the partitions including cache, cust, system and userdata. Please, what is next?
Click to expand...
Click to collapse
Ok I suspect maybe the filesystems never got created.
Can you run
Code:
df
this will show you the currently mounted partitions free space.
Output will look something like this
Code:
Filesystem Size Used Free Blksize
/dev 442.6M 60.0K 442.5M 4096
/system 1.2G 948.5M 241.8M 4096
/data 5.2G 2.8G 2.4G 4096
/cache 147.2M 176.0K 147.0M 4096
/persist 3.9M 776.0K 3.1M 4096
/firmware 99.8M 46.8M 52.9M 2048
If you dont see data or cache they never got mounted at twrp start, system is not mounted by default.
Then if data is not listed try
Code:
mount -t ext4 /dev/block/bootdevice/by-name/userdata /data
Remember to have spaces between arguments.
Or try system by replacing "userdata" with "system" and "/data" with "/system"
If you get an error trying to mount please do the following referring to the attached screenshots.
In twrp, go to "wipe", "advanced wipe". Then select one of the partitions and select "repair or change filesystem".
This should give you info about the partition.
If you wish to reformat it select "change filesystem" then select "ext4" and swipe to confirm.
Now retry the mount command and hopefully it will succeed.
Do this for each partition then retry your backup/flash.
Hopefully this works, good luck.
Thanks for your help. At first i couldn't see cache or data partition. I did what you told me, and i made cache to appears with df command. System too. But i couldn't made the same with the userdata partition. I tried to repair but it didn't work.
Is there another way to remount that partition?
A question apart: what was that "cust" partiton i've got and you didn't in your images posted in cm12.1 post? Because i recalculated it too.
beatLeo said:
Thanks for your help. At first i couldn't see cache or data partition. I did what you told me, and i made cache to appears with df command. System too. But i couldn't made the same with the userdata partition. I tried to repair but it didn't work.
Is there another way to remount that partition?
A question apart: what was that "cust" partiton i've got and you didn't in your images posted in cm12.1 post? Because i recalculated it too.
Click to expand...
Click to collapse
Hi,
Does twrp show the userdatas partition filesystem type? Like in my previous screenshot cache is shown as ext4.
If not can you try change filesystem instead of the repair option and choose ext4.
I removed my cust partition altogether as I had no use for it.
DestructoSphere said:
Hi,
Does twrp show the userdatas partition filesystem type? Like in my previous screenshot cache is shown as ext4.
If not can you try change filesystem instead of the repair option and choose ext4.
I removed my cust partition altogether as I had no use for it.
Click to expand...
Click to collapse
Yes, it shows current file system: ext4. I tried repair and change file system but nothing. When i'm trying to use "mount -t ext4 /dev/..." it says "failed: invalid argument"
What else could i do?
I really appeciate your help man.
P.S: Sorry, i don't know why the screenshot looks not vertical.
beatLeo said:
Yes, it shows current file system: ext4. I tried repair and change file system but nothing. When i'm trying to use "mount -t ext4 /dev/..." it says "failed: invalid argument"
What else could i do?
I really appeciate your help man.
P.S: Sorry, i don't know why the screenshot looks not vertical.
Click to expand...
Click to collapse
Ok for some reason filesystem seems to have issues.
Can you please try
Code:
mkfs.ext2 -j /dev/block/bootdevice/by-name/userdata
to manually format it?
Remember spaces before and after -j option.
DestructoSphere said:
Ok for some reason filesystem seems to have issues.
Can you please try
Code:
mkfs.ext2 -j /dev/block/bootdevice/by-name/userdata
to manually format it?
Remember spaces before and after -j option.
Click to expand...
Click to collapse
It says mkfs.ext2: lseek: Value too large for define data type
beatLeo said:
Ok for some reason filesystem seems to have issues.
Can you please try
It says mkfs.ext2: lseek: Value too large for define data type
Click to expand...
Click to collapse
As far as I know that happens when you break some size limit.
How big did you make your userdata partition? Maybe you had a typo so I'm thinking you may want to run through the guide again to check but first can you let me know what you get if you write
Code:
blockdev --getsize64 /dev/block/bootdevice/by-name/userdata
DestructoSphere said:
As far as I know that happens when you break some size limit.
How big did you make your userdata partition? Maybe you had a typo so I'm thinking you may want to run through the guide again to check but first can you let me know what you get if you write
Code:
blockdev --getsize64 /dev/block/bootdevice/by-name/userdata
Click to expand...
Click to collapse
it says 5465161216
beatLeo said:
As far as I know that happens when you break some size limit.
How big did you make your userdata partition? Maybe you had a typo so I'm thinking you may want to run through the guide again to check but first can you let me know what you get if you write
it says 5465161216
Click to expand...
Click to collapse
Ok the number seems ok.
Can you please try using parted again with the guide to delete then recreate the partition making sure to specify the filesystem.
Hopefully that works but if not I think you need to rewrite the partition table a start again.
If it doesn't work can you please post the output from
Code:
parted
unit s
print free
DestructoSphere said:
Ok the number seems ok.
Can you please try using parted again with the guide to delete then recreate the partition making sure to specify the filesystem.
Hopefully that works but if not I think you need to rewrite the partition table a start again.
If it doesn't work can you please post the output from
Code:
parted
unit s
print free
Click to expand...
Click to collapse
Hi DestructoSphere,
tried to do that, but remember i can't get to adb so i can't find a way to paste the parted file into de sbin. Any ideas about that?
beatLeo said:
Ok the number seems ok.
Can you please try using parted again with the guide to delete then recreate the partition making sure to specify the filesystem.
Hopefully that works but if not I think you need to rewrite the partition table a start again.
If it doesn't work can you please post the output from
Hi DestructoSphere,
tried to do that, but remember i can't get to adb so i can't find a way to paste the parted file into de sbin. Any ideas about that?
Click to expand...
Click to collapse
In twrp can you mount mtp or usb storage and copy it to sdcard then twrp filemanager to copy to sbin?
Ok, i tried with a sdcard, but i couldn't either. It didn't recognize my sdcard. And i don't have an otg's usb.
But in twrp's cmd showed "mtp enabled". Could this means that i have to mounted the sd partition? If that is a yes, could you please write me the code ?
beatLeo said:
Ok, i tried with a sdcard, but i couldn't either. It didn't recognize my sdcard. And i don't have an otg's usb.
But in twrp's cmd showed "mtp enabled". Could this means that i have to mounted the sd partition? If that is a yes, could you please write me the code ?
Click to expand...
Click to collapse
Hi DestructoSphere, i finally resolve this. It was a lot simplier than you ever thought. I tried changing to ext2 my data partion, and then change it again to ext4 and that's how it works again.
Take a look into my partitions. But i still want to reduce to 100mb the modem partition.
Can't flash anything through recovery. (failed to mount "/cpefs" (Invalid Response)
I recently got this phone and I've been trying to install a custom rom, however, I can't seem to do anything while using TWRP. For some reason the file explorer shows no files and no /storage folder. It also says that the /system partition weights 0MB. I've already tried formatting the /data partition from EXT4 to extFAT, but it won't let me because it cannot mount the "/cpefs" partition, which I've been unable to find any information about.
I can flash the stock firmware trough ODIN, and I can flash the recovery. The internal storage works fine, but nothing shows up when I open TWRP.
I've tried formatting the data partition, repairing it, changing the partition format, wiping, installing a custom rom, installing superSU. But it won't allow me to do any of those things. Either "/data" can't be mounted, or "/cpefs" can't be mounted while formatting /data.
Cepillado said:
I recently got this phone and I've been trying to install a custom rom, however, I can't seem to do anything while using TWRP. For some reason the file explorer shows no files and no /storage folder. It also says that the /system partition weights 0MB. I've already tried formatting the /data partition from EXT4 to extFAT, but it won't let me because it cannot mount the "/cpefs" partition, which I've been unable to find any information about.
I can flash the stock firmware trough ODIN, and I can flash the recovery. The internal storage works fine, but nothing shows up when I open TWRP.
I've tried formatting the data partition, repairing it, changing the partition format, wiping, installing a custom rom, installing superSU. But it won't allow me to do any of those things. Either "/data" can't be mounted, or "/cpefs" can't be mounted while formatting /data.
Click to expand...
Click to collapse
Which phone you're using?
J7 Pro?
Secondly make sure to enable OEM unlock options from the stock ROM's Developer option!
Thirdly check the recovery patches etc of the desired recovery's webiste (you're using) and flash it through the recovery if you're facing the problem!
It'll work, mostly some users said they fixed this by the above mentioned step!
If no luck, maybe someone will sort it out for ya, soon! :laugh:
Good Luck! :good:
sosukeaizen said:
Which phone you're using?
J7 Pro?
Secondly make sure to enable OEM unlock options from the stock ROM's Developer option!
Thirdly check the recovery patches etc of the desired recovery's webiste (you're using) and flash it through the recovery if you're facing the problem!
It'll work, mostly some users said they fixed this by the above mentioned step!
If no luck, maybe someone will sort it out for ya, soon! :laugh:
Good Luck! :good:
Click to expand...
Click to collapse
Thanks for your reply. The model of the phone is SM-J710MN. The OEM unlock option is enabled, otherwise I wouldn't be able to flash the recovery. I am trying to use TWRP. Where would I find a recovery patch for this model?. Everything works fine in the recovery, but it won't let me wipe/format/repair or change ANY partition. It can't mount anything, and the error that I see the most often is that it cannot mount the /cpefs partition.
Cepillado said:
Thanks for your reply. The model of the phone is SM-J710MN. The OEM unlock option is enabled, otherwise I wouldn't be able to flash the recovery. I am trying to use TWRP. Where would I find a recovery patch for this model?. Everything works fine in the recovery, but it won't let me wipe/format/repair or change ANY partition. It can't mount anything, and the error that I see the most often is that it cannot mount the /cpefs partition.
Click to expand...
Click to collapse
try flashing a lower version of the same frimware you've already installed e.g if the latest is nougat 7.1.1 with the recent security update, try flashing with another nougat version that is lower to the recent one's security patch #