Hi,
I searched the forum, wiki, etc., but didn't find an answer.
I have an AT&T Fuze with the stock ROM (WM 6.1). I know the Fuze is supposed to support multiple simultaneous bt connections. What I would like to do is connect A2DP to my Pioneer stereo for music playback, and also connect handsfree to my Jawbone 2 headset for phone calls while in the car.
I can successfully connect A2DP to my stereo for music by itself.
I can successfully connect HFP to my Jawbone 2 by itself.
I *have* managed to connect to both at the same time, by staying on an active phone call with my Jawbone, then telling my Fuze to connect to the car stereo. However, no music could be heard (from either Mortplayer or WMP). The phone call stayed up just fine though.
Anyone know if there's a way to get both working at the same time?
(And before you ask, I would just use the hands-free capability of my Pioneer stereo for phone calls too, but I've found my car is too noisy for anyone to hear me with the Pioneer's microphone unless I hold it right in front of my mouth, which defeats the "hands free" goal...)
Thanks for any help you can offer.
Best,
Chris
In your case I do not think that is possible since the concept of being able to juggle 2 devices at the same time requires 1 to relinquish control while the other goes active. It turns off the music so you do not get distracted while talking and reconects the music after the call is over.
It seems to be a software protocol if anything. Yes both can be connected at the same time, but both cannot be "active" as in doing both music playback and voice calls.
I have a bt headset that handles 2 profiles at once and according to the protocol, if a call comes in, it pauses my ipod and then picks up the call and then resets back to normal after the call.. Either you have to mess with the coding itself or someone has to come up with a workaround, but I do not think that is possible.
Thanks for the reply. I had hoped it might be possible for the Fuze to route stereo audio to one BT profile (A2DP), while non-stereo audio (e.g., phone call, system tones, etc.) to the HFP profile, almost as though the profiles acted as addressable "service ports" (ala HTTP, SMTP, etc.).
But, unlike with TCP/IP, I admit to knowing next to nothing about how the BT stack works and how profiles are applied to certain types of data (or, how data is routed to a given BT association based on profile).
Thanks again,
Chris
well the thing is.. the fuze can connect to multiple devices simultaneously, but based on the music and voice call order, it is prohibited from doing both at the same time. so therefore when there is no call, the music plays, but when a call comes it, the music is paused and resumed after the call is done. (obviously the call has higher priority here).
My only suggestion is to leave it as it is since it is done so that you do not get distracted while talking and probably while you're driving.
Multitasking is difficult when you're listening to 2 things, responding to 1, and driving at the same time. The more you multitask the less you are able to devote to your main activity (in your case, driving).
but yeah. if you can find someone who can mess with that and allow for both to be active at the same time, then congrats. Otherwise just think of it as a safety measure.
Except that, when I had both the headset and the stereo connected to the Fuze, the music *didn't* pause. It just didn't output (as though the volume was muted). In fact, in both Mortplayer and WMP, it appeared as though it was playing at ~2X the normal rate (just watching the track playback time counter).
I know what you're talking about re: listen to music, call comes in, music pauses, call ends, music resumes. That's the behavior I get when I use the car stereo for both handsfree and A2DP.
The behavior when connected to two different devices seemed to be different, though, so I hoped that might mean it was in fact possible.
-Chris
yeah I know what you mean, but maybe the fact that it tried to do both tripped it up and so it took the call as a higher priority and focused the data towards the call.
atleast that is what I think.
I have almost the exact same configuration, except I am using a Sony car stereo but have a jawbone. What I have to do every time I get in the car is the following.
1. Let my stereo connect to both hands free and wireless headphone services.
2. Open bluetooth settings
3. Manually connect to my Jawbone.
It works great.
ATT Fuze
Energy Rom 072209
Old jawbone
Sony XPLOD Car Stereo
I'll also add it's pretty neat to be able to push the jawbone to activate MS Voice Commander and choose what music I want to play over my car stereo.
frankrizzo said:
What I have to do every time I get in the car is the following.
1. Let my stereo connect to both hands free and wireless headphone services.
2. Open bluetooth settings
3. Manually connect to my Jawbone.
It works great.
Click to expand...
Click to collapse
Thanks for the reply. I'll give that a shot. I'm not sure that my Pioneer stereo will automatically connect both handsfree and A2DP. I know it will do handsfree automatically. We'll see...
-Chris
Hello,
I have a car which supports only Bluetooth Phone option and this is the case of a lot of bluetooth car devices.
So I'm perfectly able to receive and send phone call but I cannot send music to the car speakers through Bluetooth (this is really due to bluetooth car device and not phone itself).
I'm wondering if it might be possible to emulate phone dialog in order to let the car thought it is receiving a phone communication and so play it.
Phone Music --> Phone call emulation in Bluetooth (caller voice normally transmitted is replaced by music played) ....> Car bluetooth phone call reception --> Speakers
It should be probably needed too to emulate car bluetooth receiver as a bluetooth sound player (in order to cheat android phone) .
Thanks to share your opinion / ideas.
Olivier
Music is usually routed to Media channel on the phone. Maybe avoiding that could be the solution. Figure out a way to route the audio to the Ringer for example. That might work.
Sent from my MT15i using XDA
I use my N5 in my car which has built-in bluetooth (Ford Focus, 2011 w/ sync).
The in-car speakerphone mode works great. However, the car doesn't send audio to the phone other than during a call. And since the phone sees a BT headset connected, it disables its own mic. So things like google now and voice commands don't work. And the car does voice-commanded dialing through its own phonebook rather than the phone's phonebook. So I have to regularly sync the two to keep the car's database updated.
Is there a way to have the N5 use the car only as a A2DP and AVRCP device, until a phone call comes in, and then switch over to a headset profile? That way I could still use the phone's mic for voice commands but have the car's speakers/mic handle calls.
timropp said:
I use my N5 in my car which has built-in bluetooth (Ford Focus, 2011 w/ sync).
The in-car speakerphone mode works great. However, the car doesn't send audio to the phone other than during a call. And since the phone sees a BT headset connected, it disables its own mic. So things like google now and voice commands don't work. And the car does voice-commanded dialing through its own phonebook rather than the phone's phonebook. So I have to regularly sync the two to keep the car's database updated.
Is there a way to have the N5 use the car only as a A2DP and AVRCP device, until a phone call comes in, and then switch over to a headset profile? That way I could still use the phone's mic for voice commands but have the car's speakers/mic handle calls.
Click to expand...
Click to collapse
I think you can do it with Utter! and Tasker.
Sent from my Nexus 5
Not sure what utter is needed for - I will look into getting tasker to do it.
Hello everyone,
I have a specific problem with a bluetooth device and with my limited knowledge I haven't worked out how to fix it, so I am asking for your help. I will explain it best I can...
I have a third-party bluetooth stereo in my car that has a built in mic for voice calls. However, the microphone is of terrible quality and as it's in the stereo unit it's quite far from me when I'm driving meaning it is almost useless to use for voice calls. Because of this I purchased a seperate good quality bluetooth speaker/mic that fits on to the car's sun visor. The problem I have is when I get in to my car my phone connects to the stereo only and not the small speaker. I want my phone to connect to the stereo via b/t so I can play my music through it, which is great, but not for voice calls. I see in the b/t options on my phone (HTC One) that you can check/uncheck boxes for the type of connections, in this case 'Phone Audio' and 'Media Audio'. If I just have the Media Audio setting checked, the phone fails to connect to the stereo at all, not even for music, so in order for it to automatically connect to the stereo I need the Phone Audio option enabled too, causing it to then not connect to the seperate device, thus diverting all calls through the stereo, which is really inconvenient. There are no options within the stereo that isolates these individual settings.
Are there any apps or methods you can advise me on that will allow my phone to connect to the stereo automatically but with voice disabled? I have looked in to Tasker but I am not skilled enough to work out how to set it up, so if this is the best option can somebody talk me through this please?
I appreciate the help on this, and I hope I've explained it adequately.
Simon
I am having issues figuring out how to best manage bluetooth on my device.
I use a bluetooth headset, and separate bluetooth headphones.
I am having the following problems:
1. If I am on a call and my headphones are on lying on my desk from an earlier music session, when I answer the call it goes to headphones. Thats OK, but sometimes I just want to speak on the phone. So I hit the bluetooth icon on my call screen to just speak into the handset. This works but after a few seconds it automatically keeps connecting unless I turn off the headphones. Is there any way to keep this from happening other than switching it off (which sometimes is a pain since it may be packed away in a bag, etc.)
2. Similar problem except between bluetooth devices. The call may get answered by my headset, and then during the call it ends up switching to the headphones. Is there any way to prioritize between two different bluetooth audio devices that are both connected in terms of which one you prefer to handle the phone calls?
Thanks.