Related
On July 20th 2013, I bought a new Verizon Galaxy S3 i535 (no contract due to I need unlimited data). As a 50 year old guy, I admit that I never rooted before. I decided to do some research on the web which also included this XDA site. By the way, this is the best site!!
As someone who never rooted, I found multiple different ways of rooting which caused great confusion. Some told me to download Odin, while some did not. Some told me to download a superSU or something like that, while other directions did not, and so on and on......
But what really concerns me is that most of the directions were written back in 2012. Should this be a concern?
I don't want to seem like a retard or impose, but would someone do a video skype with me and walk me thru rooting my phone for the very first time? Perhaps during that skype session I could ask a few questions? I would pre download all files so that the session would not take too long.
Any volunteers?
Respectfully,
Bryan
All you need to Do is visit this link:
http://forum.xda-developers.com/showthread.php?p=42791826
Those are the most straight forward directions you can find. And it will Root, unlock your bootloader, and install a custom recovery.
thank you for the reply. this is yet another way off rooting. why does this not use Odin? will this method allow me to undo or fix something if something goes bad?
BKSinAZ said:
thank you for the reply. this is yet another way off rooting. why does this not use Odin? will this method allow me to undo or fix something if something goes bad?
Click to expand...
Click to collapse
It doesn't use Odin because it doesn't need to. The one click solution includes all the tools needed to make the necessary changes to your phone.
If something goes wrong, then you would use Odin to go back to stock no matter what root /unlock method you used. This is because Odin has the lowest level access to your phone, and can rescue it as long as you can boot into download mode.
As long as you don't flash files intended for other phones (including s3s from other carriers) your phone should be safe.
Sent from my SCH-I535 using xda app-developers app
Please read forum rules before posting
Questions and Help issues go in Q&A and Help section
Thread moved
Thank you for your cooperation
Friendly Neighborhood Moderator
funnyperson1 said:
It doesn't use Odin because it doesn't need to. The one click solution includes all the tools needed to make the necessary changes to your phone.
If something goes wrong, then you would use Odin to go back to stock no matter what root /unlock method you used. This is because Odin has the lowest level access to your phone, and can rescue it as long as you can boot into download mode.
As long as you don't flash files intended for other phones (including s3s from other carriers) your phone should be safe.
Sent from my SCH-I535 using xda app-developers app
Click to expand...
Click to collapse
Ok... here is one of my last questions before I begin the root process....
Do I need to make a backup of my stock phone? There are no pictures or music, but do I need to make a backup in anyway first so if things go bad I can return to stock?
BKSinAZ said:
Ok... here is one of my last questions before I begin the root process....
Do I need to make a backup of my stock phone? There are no pictures or music, but do I need to make a backup in anyway first so if things go bad I can return to stock?
Click to expand...
Click to collapse
I'm going to pop in here and help out. Once you do the casual root process, it will also install a recovery for you. You can make a nandroid backup with your recovery and just keep that somewhere safe. There are also directions on how to recover and return your phone to Verizon here. Hope that answers your question.
BKSinAZ said:
Ok... here is one of my last questions before I begin the root process....
Do I need to make a backup of my stock phone? There are no pictures or music, but do I need to make a backup in anyway first so if things go bad I can return to stock?
Click to expand...
Click to collapse
No, as I said above, as long as you can reach download mode on your phone you can always Odin back to stock. If you somehow break download mode, then your phone is pretty much bricked without sending it out to someone with a JTAG programmer. The risk of that happenning though is minimal unless you flash a ROM intended for a different device (such as the international i9300 S3).
funnyperson1 said:
No, as I said above, as long as you can reach download mode on your phone you can always Odin back to stock. If you somehow break download mode, then your phone is pretty much bricked without sending it out to someone with a JTAG programmer. The risk of that happenning though is minimal unless you flash a ROM intended for a different device (such as the international i9300 S3).
Click to expand...
Click to collapse
OK... did exactly what you and the directions stated. Upon the phone booting up, there is a 'padlock' and the option to swipe. When I swipe, I am not as the home screen that I am accustomed to. I am in the Team Win Recovery Project" with the only option to 'select zip to install" and 6 buttons to press (install, backup, mount, advanced, wipe, restore, settings, reboot)
This was an unexpected step and was wondering what to do next?.... or did I mess things up?
BKSinAZ said:
OK... did exactly what you and the directions stated. Upon the phone booting up, there is a 'padlock' and the option to swipe. When I swipe, I am not as the home screen that I am accustomed to. I am in the Team Win Recovery Project" with the only option to 'select zip to install" and 6 buttons to press (install, backup, mount, advanced, wipe, restore, settings, reboot)
This was an unexpected step and was wondering what to do next?.... or did I mess things up?
Click to expand...
Click to collapse
It sounds like you were successful in rooting and unlocking your phone's bootloader. The program you are seeing (TWRP recovery) allows you to flash roms/mods (install), backup your phone, wipe and restore your phone. However, this shouldn't be what you see on bootup unless you pressed volume up while booting. Your stock ROM may have been wiped during the root process.
I suggest you dive into the world of Custom ROMs with CleanROM which is basically a de-bloated and tweaked version of the stock ROM.
Download the file from here:
http://forum.xda-developers.com/showthread.php?t=1832070
Use your PC to put it on a microSD card. In TWRP recovery, perform a Factory Reset (from the Wipe Menu), then navigate to the external_sdcard and install CleanROM (from install menu). Wipe caches and reboot once installation is finished. You should boot straight into CleanROM.
funnyperson1 said:
It sounds like you were successful in rooting and unlocking your phone's bootloader. The program you are seeing (TWRP recovery) allows you to flash roms/mods (install), backup your phone, wipe and restore your phone. However, this shouldn't be what you see on bootup unless you pressed volume up while booting. Your stock ROM may have been wiped during the root process.
I suggest you dive into the world of Custom ROMs with CleanROM which is basically a de-bloated and tweaked version of the stock ROM.
Download the file from here:
http://forum.xda-developers.com/showthread.php?t=1832070
Use your PC to put it on a microSD card. In TWRP recovery, perform a Factory Reset (from the Wipe Menu), then navigate to the external_sdcard and install CleanROM (from install menu). Wipe caches and reboot once installation is finished. You should boot straight into CleanROM.
Click to expand...
Click to collapse
It seems that when I went into the backup area and made a backup (a backup of what, I do not know because I am totally new to this) and after the backup the phone rebooted to the normal home screen with all the normal icons. I even just received a phone call so I guess all is good.
I don't know what to do now that my phone is rooted. My goal was just to uninstall unwanted programs etc, So when I get the courage, I will use the CLEANROM.
Question.... do I now have to constantly update my existing root or Cleanrom once installed? Do I now avoid Verizon or Samsung updates?
BKSinAZ said:
OK... did exactly what you and the directions stated. Upon the phone booting up, there is a 'padlock' and the option to swipe. When I swipe, I am not as the home screen that I am accustomed to. I am in the Team Win Recovery Project" with the only option to 'select zip to install" and 6 buttons to press (install, backup, mount, advanced, wipe, restore, settings, reboot)
This was an unexpected step and was wondering what to do next?.... or did I mess things up?
Click to expand...
Click to collapse
If you're not ready to flash roms just touch reboot and you'll be back to your stock jellybean. In regards to the padlock, I also got that after using CASUAL and underneath the padlock it says custom. I haven't gotten a definitive answer about that but the general consensus is that it's nothing to worry about. I suppose it's just Verizon letting you know that they detected changes to your phone.
Do yourself a favor and read for days and days before you start flashing roms. You'll find the answers here and YouTube.
BKSinAZ said:
It seems that when I went into the backup area and made a backup (a backup of what, I do not know because I am totally new to this) and after the backup the phone rebooted to the normal home screen with all the normal icons. I even just received a phone call so I guess all is good.
I don't know what to do now that my phone is rooted. My goal was just to uninstall unwanted programs etc, So when I get the courage, I will use the CLEANROM.
Question.... do I now have to constantly update my existing root or Cleanrom once installed? Do I now avoid Verizon or Samsung updates?
Click to expand...
Click to collapse
Great. The backup you made is what is called a "nandroid" backup. By default it includes the Android System, your apps, and associated application data and settings. This is great because it basically includes everything you need to restore your phone to it's previous state. So if you were to flash a custom ROM and ended up not liking it you could always restore this backup and it would restore your phone to how it is now.
Being rooted allows you to install and use applications from the Play store that require root. There are tons of them. The one I use most often is called Titanium Backup. It's primary purpose it to backup and restore your data and applications on an individual basis. I use it mostly to save my text messages and game save data between ROM flashes. It also allows you to uninstall, wipe data, and freeze (disable) any application on your phone.
Right now since you are still running stock rooted, you want to avoid installing any official updates, otherwise you may have to re-root. Beanstown may have disabled system updates through the rooting method, but I am not sure. If a new update is released, keep your eyes on the forums here, someone will create a flashable zip of the new firmware that maintains root/unlocked bootloader, you can then flash that in TWRP. Also once you flash a custom ROM like CleanROM, they removed the Samsung Firmware updater most likely so you don't have to worry about it.
My Atrix 2 is currently having some serious issues. Last night I rooted it. I changed the boot animation to what was supposed to be a human eye turned droid eye or something. When I rooted it and attempted to install Safestrap it didn't install correctly. As I am inexperienced with rooting android phones, I didn't think it'd hurt. I don't know if it did. When I rebooted to see the animation it just said android in silver letters with light flashing across it and it never got past that. I did several hard resets to see if that would fix it, after trying multiple battery pulls of course, and nothing. The phone is now dead and won't charge, when I plug it in it just shows the Motorola logo and doesn't do anything, but if I unplug it the logo doesn't go away. Help, please!
CreativeSin said:
My Atrix 2 is currently having some serious issues. Last night I rooted it. I changed the boot animation to what was supposed to be a human eye turned droid eye or something. When I rooted it and attempted to install Safestrap it didn't install correctly. As I am inexperienced with rooting android phones, I didn't think it'd hurt. I don't know if it did. When I rebooted to see the animation it just said android in silver letters with light flashing across it and it never got past that. I did several hard resets to see if that would fix it, after trying multiple battery pulls of course, and nothing. The phone is now dead and won't charge, when I plug it in it just shows the Motorola logo and doesn't do anything, but if I unplug it the logo doesn't go away. Help, please!
Click to expand...
Click to collapse
Phew, that was close. Hello and welcome to the help section of the A2 forum, for starters the trouble you're facing right now is called soft bricking. It's a very common problem, but is usually solved by flashing the correct ICS sbf for your region.
So firstly, is your phone branded AT&T or is it from another region? Please specify which. Next you need to recharge your battery externally either by an external battery charger or the Mcgyver method. (search the forum for more details).
After you've charged your battery up enough, put it back in your phone and put your phone into fastboot mode by holding the volume down button + power button and make sure it says 'Battery OK'.
After making it this far, you'll need RSD lite order to flash/install the sbf files. If everything goes fine without failure, then your phone will be back to stock and you've saved it! Here's a thread that has content that should guide you with further details: http://forum.xda-developers.com/showthread.php?t=2245825 Good luck!
Sent from the Ace's MB865 using xda-developers app
Aceofzeroz said:
Phew, that was close. Hello and welcome to the help section of the A2 forum, for starters the trouble you're facing right now is called soft bricking. It's a very common problem, but is usually solved by flashing the correct ICS sbf for your region.
So firstly, is your phone branded AT&T or is it from another region? Please specify which. Next you need to recharge your battery externally either by an external battery charger or the Mcgyver method. (search the forum for more details).
After you've charged your battery up enough, put it back in your phone and put your phone into fastboot mode by holding the volume down button + power button and make sure it says 'Battery OK'.
After making it this far, you'll need RSD lite order to flash/install the sbf files. If everything goes fine without failure, then your phone will be back to stock and you've saved it! Here's a thread that has content that should guide you with further details: http://forum.xda-developers.com/showthread.php?t=2245825 Good luck!
Sent from the Ace's MB865 using xda-developers app
Click to expand...
Click to collapse
As RSDLite was rebooting my phone I checked the forums and saw this! Hahah but thank you very much! This is pretty much exactly what I ended up doing. I posted this and then read up on the forums rules and some stuff and realized I should really learn to help myself if I want to . Took some time and a lot of mistakes but I put it together. Thank you very much for the reply.
CreativeSin said:
As RSDLite was rebooting my phone I checked the forums and saw this! Hahah but thank you very much! This is pretty much exactly what I ended up doing. I posted this and then read up on the forums rules and some stuff and realized I should really learn to help myself if I want to .
Took some time and a lot of mistakes but I put it together. Thank you very much for the reply.
Click to expand...
Click to collapse
You're welcome :thumbup: I'm glad it all worked out for you in the end. I still remember the time earlier this year when I just got my phone, went crazy with mods and ended up softbricking it for a whole week. It was hell just to get it working again cuz RSD Lite decided to hate me from the get-go. -_-
So I'm glad to help others out with this, but enough rambling lol, take greater care for the next flashes you do until you get used to it!
Sent from the Ace's MB865 using xda-developers app
Aceofzeroz said:
You're welcome :thumbup: I'm glad it all worked out for you in the end. I still remember the time earlier this year when I just got my phone, went crazy with mods and ended up softbricking it for a whole week. It was hell just to get it working again cuz RSD Lite decided to hate me from the get-go. -_-
So I'm glad to help others out with this, but enough rambling lol, take greater care for the next flashes you do until you get used to it!
Sent from the Ace's MB865 using xda-developers app
Click to expand...
Click to collapse
Thanks! Just got it all rooted again no problem. I'm trying to learn all this, any tips on something I could start working on?
CreativeSin said:
Thanks! Just got it all rooted again no problem. I'm trying to learn all this, any tips on something I could start working on?
Click to expand...
Click to collapse
Well now that you're back and rooted, if you're planning on doing any more flashing any time soon then I recommend you install boot menu manager. If you've previously installed safestrap or bootstrap, clear their data and uninstall them before installing bmm.
With that done, you've just made your phone a little safer from bricking because bmm allows multi rom booting, which are somewhat independent of the primary system. Refer to this thread for more info on how to make systems, etc.: http://forum.xda-developers.com/showthread.php?t=2115715
The first thing you'd want to do is make sure your apps/data is always backed up at all times with apps like titanium backup. Create 2 or more systems so that you can try the bmm compatible custom ROMs which are in the dev section if you want to try any of them. But please, read all instructions, warnings, requirements, etc. carefully before attempting any flashing in general.
The thread I posted in my earlier post above will have links to the specific custom ROMs. If you're doing any other kind of flashing, make sure to again, read instructions carefully and take your time with learning all of this.
Hi, I soft bricked my phone recently.
I was running stock ICS from Moto on a rooted Atrix 2. I wanted to upgrade it to JB so I installed Atrix 2 bootstrap and clicked Bootstrap Recovery (gave superuser permission) and then Reboot Recovery. It went into CWM and I wiped factory data and cache. Before I installed the JB zip I backed up my old ICS via CWM and then installed CyanogenMod-Dev-edison-nightly-20130401-2132-signed.591fan.com zip.
It was upgraded successfully to 4.2.2 but I couldnt get my updated contacts from the Super Recovery app, so I thought to restore the old ICS and backup the contacts once again. I installed Atrix 2 bootstarp apk again and went thought the same process ( Bootstrap recovery > gave Superuser permission > Reboot recovery). As soon as it rebooted the Motorola logo came on and after that the phone gave dark grey screen. I tried rebooting and going into CWM on startup but it didnt give the option of install zip from sd card as it did on my earlier attempt.
I am stuck with a bricked phone and all my work is stuck up.
I read about RSDlite but I have heard it causes hard bricking on several occasion. So, I am a bit cautious about using it and I dont know the exact procedure to use it also. Can you please guide me on how to regain my phone from this soft brick and where i went wrong during my installations.
Any help would be very much appreciated. Thanks a lot in advance.
kunal2711 said:
Hi, I soft bricked my phone recently.
I was running stock ICS from Moto on a rooted Atrix 2. I wanted to upgrade it to JB so I installed Atrix 2 bootstrap and clicked Bootstrap Recovery (gave superuser permission) and then Reboot Recovery. It went into CWM and I wiped factory data and cache. Before I installed the JB zip I backed up my old ICS via CWM and then installed CyanogenMod-Dev-edison-nightly-20130401-2132-signed.591fan.com zip.
It was upgraded successfully to 4.2.2 but I couldnt get my updated contacts from the Super Recovery app, so I thought to restore the old ICS and backup the contacts once again. I installed Atrix 2 bootstarp apk again and went thought the same process ( Bootstrap recovery > gave Superuser permission > Reboot recovery). As soon as it rebooted the Motorola logo came on and after that the phone gave dark grey screen. I tried rebooting and going into CWM on startup but it didnt give the option of install zip from sd card as it did on my earlier attempt.
I am stuck with a bricked phone and all my work is stuck up.
I read about RSDlite but I have heard it causes hard bricking on several occasion. So, I am a bit cautious about using it and I dont know the exact procedure to use it also. Can you please guide me on how to regain my phone from this soft brick and where i went wrong during my installations.
Any help would be very much appreciated. Thanks a lot in advance.
Click to expand...
Click to collapse
Use boot menu manager instead of bootstrap recovery
Sent from my MB865 using XDA Premium 4 mobile app
I got my phone rooted , got the last update XNPH05Q installed but have a lot of problems
How can I do a factory reset ?
I read that sometimes it is also ok to flash the rom but where do I find that rom ?
I also have a backup on my PC from 22/11/2014 just after I have rooted my phone .
Some good advice please ?
Turn the phone off, hold vol down and power at the same time, boot into recovery and wipe data. That will erase the OS and you'll reboot into the setup phase.
so I will come back in the original OS ? CyanogenMod(11S) ?
And why not use factory settings on the device ?
Correct me if im wrong but wouldnt that just get you into a bootloop because there is no OS at all ?
But im Not an expert.
Sent from my HTC EVO 3D X515m using XDA Free mobile app
None of those answers are correct. A factory reset only resets user data (apps and settings), it will not erase the OS, it will not put the phone into a bootloop, it will not return the phone to a previous OS. All it does is erase your apps and settings.
@zaiko2000, I'm assuming the backup you have was made by TWRP? If so, you can just restore that to roll back.
Transmitted via Bacon
Thanks for the quick reply but one more question . Wouldn't it be better to start from the beginning ? I mean go back to the original state since I rooted the phone and then installed the update .
Can I do that with the factory reset or do you think install the backup again is better ?
I found also a bacon root kit what seems to be easy .
zaiko2000 said:
Thanks for the quick reply but one more question . Wouldn't it be better to start from the beginning ? I mean go back to the original state since I rooted the phone and then installed the update .
Can I do that with the factory reset or do you think install the backup again is better ?
I found also a bacon root kit what seems to be easy .
Click to expand...
Click to collapse
The most valuable piece of advice I can give you is to stay away from toolkits, they're more trouble than they're worth, plus they allow you to do things to your phone without actually knowing what's going on, which bypasses some very crucial learning and experience, and it's that experience that'll get you out of trouble in future when/if something goes wrong.
Anyway, the best way to do it is probably to start fresh, and the best way to start fresh is by wiping and flashing the stock images with fastboot. You'll find full instructions in section 8 of my guide thread here:
http://forum.xda-developers.com/showthread.php?t=2839471
The download I provide there is for the most recent update, so if you want the previous version you can get out from here:
http://builds.cyngn.com/factory/bacon/cm-11.0-XNPH44S-bacon-signed-fastboot.zip
The fastboot commands are the same.
Transmitted via Bacon
Did it this afternoon and it worked fine !!!!
Great job and many thanks !!!
I am probably not putting this in the right place, if so can a mod please move it?
My brother just got a Oneplus 3t and my dumbass ****ed it up. I followed the instructions on this video (youtube .com/watch?v=kGZyX9e7-C4) to root it, but didn't realize that the tutorial was for the 3 not the 3t (may have been the first issue i ran into.)
Every step went perfectly until the very very end. My phone was stuck on the boot screen for an excessively long time. So i ended up going back into the twrp menu and did a factory wipe, thinking it would just restore it back to factory default settings. It didn't and now it just says "No os installed are you sure you want to reboot?" I just want to restore the phone to factory settings so it can be used. Can someone please help me? I obviously have no clue what I'm doing.
edit: on a side note I did at least use a 3t img file, but I didn't think it was relevant to say.
franklyepic said:
I am probably not putting this in the right place, if so can a mod please move it?
My brother just got a Oneplus 3t and my dumbass ****ed it up. I followed the instructions on this video (youtube .com/watch?v=kGZyX9e7-C4) to root it, but didn't realize that the tutorial was for the 3 not the 3t (may have been the first issue i ran into.)
Every step went perfectly until the very very end. My phone was stuck on the boot screen for an excessively long time. So i ended up going back into the twrp menu and did a factory wipe, thinking it would just restore it back to factory default settings. It didn't and now it just says "No os installed are you sure you want to reboot?" I just want to restore the phone to factory settings so it can be used. Can someone please help me? I obviously have no clue what I'm doing.
edit: on a side note I did at least use a 3t img file, but I didn't think it was relevant to say.
Click to expand...
Click to collapse
Greetings and welcome to assist, don't panic. If you can still access twrp you can still flash the correct the correct rom for your device. You should be able to download a prerooted rom for your device from here
http://forum.xda-developers.com/oneplus-3t/development
and flash through recovery. The experts there will be able to guide you
Good Luck
Sawdoctor
I never thought that this would happen, especially after 6 years of being an ardent flashaholic but here I am like another noob requesting for guidance.
So it started a few days back when the Flashaholic in me wanted something to divert my mind from the monotonicity of a good ROM.I was using "[8.1.x][WEEKLIES] CarbonROM | cr-6.1 [bacon]" Rom on my 3 year old bacon happily when I decided to try "Crdroid ROM for OnePlus ONE crdroid-4.6".
As mentioned in the instructions I followed the steps to each word i.e. wipe,flash rom and then gapps (using modded twrp-3.2.1-K2-bacon.)and the ROM booted fine.I setup it as usual post boot however I faced few reboots which made me doubt myself so i thought of reflashing the same ROM again but the butter fingers got the best of me and while selecting partitions to WIPE( I guess) I selected some incorrect partition and after the flash my phone went into bootloop..
I tried to boot into recovery but I wasnt able to so but I knew I could boot into recovery using Fastboot so I reflashed the recovery while in fastboot mode and ran fastboot boot TWRP.img as I wasnt able to boot into recovery with VolumeDown+Power.I tried to fetch the nandroid backup but to my astonishment it was gone and my /data partition was wiped clean.I blame myself as I must have done something wrong as I was panicked.
Since then(last sunday)my phone has been in bootloop and doesnt start in recovery unless I boot recovery from fastboot. I have spent countless hours to fix it and the things I have tried already are mentioned below
1)Flash Stock rom (CM11,CM12,CM13)
2)Erase and flash persist.img
3)Flashed CM13 snapshot or bacon_firmware_update_2015_05-15_DI.3.0.c6-00241.zip followed by RR 5.8.5 ,RR 6.0 ,Carbon rom 6.1 and c-droid 4.6
4)Flashed coloros and then stock rom(CM11,CM12,CM13) or RR 5.8.5 ,RR 6.0 ,Carbon rom 6.1 and c-droid 4.6
I have gone through this awesome guide ultimate-answer-to-bacon-flavored- by @Timmmmaaahh ,other noob friendly guides indexes , compilations ,threads on softbrick and hardbrick topics and used almost every tool created for one plus one.
I have ruled out below
1)Volume button not working as I can boot into fastboot fine using VolumeUp+Power button
2)Battery not working as my phone can stay in fastboot for pretty much a day with 50% battery or bootloops throughtout the day
I am really out of my depth and I am trying to find where I had kept my nandroid backup on Laptop/Drive but I dont think even that can help me now.I have lost a lot of precious and Important data due to my panicking and wouldnt want to lose my phone so any help and guidance would be really appreciated.
Hopefully I am posting in the correct place and havent breached any XDA rules!Aplogies in advance if I have
you are sure, that you have flash thr TWRP and not only load TWRP via sideload into the ram?
please post the command, which you have send to the phone
So I use below command to install the twrp from fasboot
fasboot flash recovery <path/twrp file>
Also I've tried to flash twrp in recovery from twrp by selecting image file option but it doesn't boot into recovery ever
I've tried twrp 2.7,2.8,3.0,3.1 and 3.2 as well on every rom that I've flasher given the compatibility.
to boot into recovery as it's not accessible I use below command
Fastboor boot <path/twrp file>
Stupid thing it seems but try different micro usb cable
vedanth123456 said:
So I use below command to install the twrp from fasboot
fasboot flash recovery <path/twrp file>
Also I've tried to flash twrp in recovery from twrp by selecting image file option but it doesn't boot into recovery ever
I've tried twrp 2.7,2.8,3.0,3.1 and 3.2 as well on every rom that I've flasher given the compatibility.
to boot into recovery as it's not accessible I use below command
Fastboor boot <path/twrp file>
Click to expand...
Click to collapse
Okay, let's optimize your environment first. Make sure the path to your adb is c:\adb (don't flash stuff like "c:\users\dinky doodle\my awesome downloads\android shizzle\recovery manizzle"). Use the amazing 15 seconds adb installer and let it install the drivers as well. @kallum7 makes a good point, do try that.
Use the TWRP recommended in my guide and follow the clean flash steps (including CM13 step again).
More importantly: check md5 hashes on all your downloads. You really want to avoid flashing a corrupted recovery download. Only continue flashing ROMs once you have a stable TWRP installation going. If it's not properly booting to TWRP, do not bother flashing anything else.
When successfully booted in TWRP, make sure MTP is enabled under mount and connect it to your PC. Browse for possible backups via your computer. If you can't find any, you've probably wiped internal memory. If you didn't make a copy to your computer, the data is most likely gone forever (sorry).
Panicking is indeed a bad idea, we've all been there and it's an excellent learning process (you'll appreciate your failures later, lol). It's better to work step by step slowly, make sure you read everything thoroughly. When in doubt, just post here and we'll follow up. We'll get there, don't worry.
---------- Post added at 08:51 AM ---------- Previous post was at 08:47 AM ----------
Oh and rename the recovery file to recovery.img and place it in your adb folder to avoid any complications. Less = more!
Because I had bricked my phone a few months ago and I changed my USB cable and it worked perfect
kallum7 said:
Stupid thing it seems but try different micro usb cable
Click to expand...
Click to collapse
Thanks mate..I did try that but it didn't endure fruitful results
Timmmmaaahh said:
Okay, let's optimize your environment first. Make sure the path to your adb is c:\adb (don't flash stuff like "c:\users\dinky doodle\my awesome downloads\android shizzle\recovery manizzle"). Use the amazing 15 seconds adb installer and let it install the drivers as well. @kallum7 makes a good point, do try that.
Use the TWRP recommended in my guide and follow the clean flash steps (including CM13 step again).
More importantly: check md5 hashes on all your downloads. You really want to avoid flashing a corrupted recovery download. Only continue flashing ROMs once you have a stable TWRP installation going. If it's not properly booting to TWRP, do not bother flashing anything else.
When successfully booted in TWRP, make sure MTP is enabled under mount and connect it to your PC. Browse for possible backups via your computer. If you can't find any, you've probably wiped internal memory. If you didn't make a copy to your computer, the data is most likely gone forever (sorry).
Panicking is indeed a bad idea, we've all been there and it's an excellent learning process (you'll appreciate your failures later, lol). It's better to work step by step slowly, make sure you read everything thoroughly. When in doubt, just post here and we'll follow up. We'll get there, don't worry.
---------- Post added at 08:51 AM ---------- Previous post was at 08:47 AM ----------
Oh and rename the recovery file to recovery.img and place it in your adb folder to avoid any complications. Less = more!
Click to expand...
Click to collapse
Hi mate,So I pulled an all nighter yesterday and was somehow magically able to boot in TWRP.I don't remember what I did but I booted into TWRP 2.8.7.0 and the first thing I did was check if any nandroid backup was there but I was disappointed to see my /data with free 55326 MB also no backups on my drive.All my data is gone and I can't curse myself enough for that,moving on so I did manage to gather my sense and flashed TWRP 3.2.1-K2 and flashed RR-O-v6.1.0 but the phone goes into boot loop again and again.
Since then my phone is displaying some weird behavior so if I unplug my device and start my phone the phone won't boot and wont go past oneplus one splashscreen so I thought my battery is gone but if I can go in fastboot mode or TWRP mode while being plugged in and unplug my device but my phone wont die,it'll be in the respective mode for ages.
I do have a clean setup (K:\oneplus\adb\) that's how I stayed away from this mess since ages but I guess I got too cocky.
I have religiously followed your thread and it has helped me a lot so once I am home I will check the TWRP part again and get back with the results.
Once again..thanks for your guidance.
vedanth123456 said:
Hi mate,So I pulled an all nighter yesterday and was somehow magically able to boot in TWRP.I don't remember what I did but I booted into TWRP 2.8.7.0 and the first thing I did was check if any nandroid backup was there but I was disappointed to see my /data with free 55326 MB also no backups on my drive.All my data is gone and I can't curse myself enough for that,moving on so I did manage to gather my sense and flashed TWRP 3.2.1-K2 and flashed RR-O-v6.1.0 but the phone goes into boot loop again and again.
Since then my phone is displaying some weird behavior so if I unplug my device and start my phone the phone won't boot and wont go past oneplus one splashscreen so I thought my battery is gone but if I can go in fastboot mode or TWRP mode while being plugged in and unplug my device but my phone wont die,it'll be in the respective mode for ages.
I do have a clean setup (K:\oneplus\adb\) that's how I stayed away from this mess since ages but I guess I got too cocky.
I have religiously followed your thread and it has helped me a lot so once I am home I will check the TWRP part again and get back with the results.
Once again..thanks for your guidance.
Click to expand...
Click to collapse
This is weird I just restarted my phone to see if it magically starts but it went into bootloop(displaying splashscreen not boot logo) in contrast to earlier when it died instantly when not plugged in also I can't boot into my recovery now!
Once I am plugged in and the phone is on bootloop and if I hold the volumedown+Powerkey it boots into TWRP properly..
This is just weird and I havent seen this behavious in the past three years of using my old lovely bacon
Try using the color os toolkit https://steemit.com/oneplus/@delusionalgenius/how-to-unbrick-oneplus-one-bacon and even though it says do not use if it is soft bricked use it this helped me
Sorry for getting back rather late (again). I'm in the middle of organizing an event and it's leaving very little XDA time. Anyway...
Isn't a hardbrick tutorial kinda agressive? I mean, I've used it before, and it's excellent, but then my device was actually hardbricked. I'd rather go for the 'back to stock' method first, setting the system back to CM13, which is a much better base for further flashing compared to ColorOS.
@vedanth123456 if you didn't take any action yet then I suggest following this thread (skip step 4!!).
The deal is to flash all images from fastboot. This will – naturally – wipe every single partition on your device!
I suggest doing the fastboot flashing manually (copy paste each command one by one) to avoid your device getting its bootloader locked. You DO NOT want to lock the bootloader on a OnePlus One if you ever wish to unlock it again.
When you successfully booted CM13, go though its initial setup, [disable recovery protection in system or developer settings] (it's been so long since I've experienced this process that I'm not sure if this option was present in CM13; if you can't find it, don't mind), get back to fastboot mode and flash K2 TWRP. First thing to do at this point: create a full nandroid backup of your working CM13 setup and copy it externally. ROM flashing should now be successful. If not, I'm afraid your hardware is failing. Do try several ROMs.
Don't forget to check those md5 hashes!
By the way, your /data is supposed to be empty after a factory reset. /data merely contains settings and app data (user added information). Backups and user media go to the /sdcard partition, which is known as internal memory. If I may suggest a ROM, go for CrDroid. It's more stable compared to RR, it's still actively developed and it has similar features.
Timmmmaaahh said:
Sorry for getting back rather late (again). I'm in the middle of organizing an event and it's leaving very little XDA time. Anyway...
Isn't a hardbrick tutorial kinda agressive? I mean, I've used it before, and it's excellent, but then my device was actually hardbricked. I'd rather go for the 'back to stock' method first, setting the system back to CM13, which is a much better base for further flashing compared to ColorOS.
@vedanth123456 if you didn't take any action yet then I suggest following this thread (skip step 4!!).
The deal is to flash all images from fastboot. This will – naturally – wipe every single partition on your device!
I suggest doing the fastboot flashing manually (copy paste each command one by one) to avoid your device getting its bootloader locked. You DO NOT want to lock the bootloader on a OnePlus One if you ever wish to unlock it again.
When you successfully booted CM13, go though its initial setup, [disable recovery protection in system or developer settings] (it's been so long since I've experienced this process that I'm not sure if this option was present in CM13; if you can't find it, don't mind), get back to fastboot mode and flash K2 TWRP. First thing to do at this point: create a full nandroid backup of your working CM13 setup and copy it externally. ROM flashing should now be successful. If not, I'm afraid your hardware is failing. Do try several ROMs.
Don't forget to check those md5 hashes!
By the way, your /data is supposed to be empty after a factory reset. /data merely contains settings and app data (user added information). Backups and user media go to the /sdcard partition, which is known as internal memory. If I may suggest a ROM, go for CrDroid. It's more stable compared to RR, it's still actively developed and it has similar features.
Click to expand...
Click to collapse
Hi mate
Apologies for not acknowledging your message and not replying back earlier. I've been traveling using a spare phone and things just aren't the same on it.
To give u an update, I tried the steps mentioned in the link (which I had tried previously as well) but the phone didn't boot. Same bootlooping and issue with the twrp.
So I went through other forums and links and finally found an exe that worked.!!!!!! So the exe seems to be an modified version of the one mentioned in the hard brick method and has been created by someone else (NOT ME!!)
My phone after many moons has booted and its on the good old cyanogen CM 11.0 XNPH44S. I've tried numerous roms on this bad boy but there is some beauty in the simplicity of the good old roms.
My phone battery is charging pretty slowly and wifi is not turning on so I'm still tensed but the fact that it booted is a small victory. I would want to upgrade to a stable rom once my phone is charged and not displaying erratic behavior so I'll wait for a day and see how it works but I'll want to upgrade to a slightly latest rom probably not a battery hogging one.
I believe I'll have to first install an old twrp followed by nandroid backup(save on every goddammed devices I own), then some CM snapshot and finally the rom but please can you confirm and suggest.
vedanth123456 said:
Hi mate
Apologies for not acknowledging your message and not replying back earlier. I've been traveling using a spare phone and things just aren't the same on it.
To give u an update, I tried the steps mentioned in the link (which I had tried previously as well) but the phone didn't boot. Same bootlooping and issue with the twrp.
So I went through other forums and links and finally found an exe that worked.!!!!!! So the exe seems to be an modified version of the one mentioned in the hard brick method and has been created by someone else (NOT ME!!)
My phone after many moons has booted and its on the good old cyanogen CM 11.0 XNPH44S. I've tried numerous roms on this bad boy but there is some beauty in the simplicity of the good old roms.
My phone battery is charging pretty slowly and wifi is not turning on so I'm still tensed but the fact that it booted is a small victory. I would want to upgrade to a stable rom once my phone is charged and not displaying erratic behavior so I'll wait for a day and see how it works but I'll want to upgrade to a slightly latest rom probably not a battery hogging one.
I believe I'll have to first install an old twrp followed by nandroid backup(save on every goddammed devices I own), then some CM snapshot and finally the rom but please can you confirm and suggest.
Click to expand...
Click to collapse
Heya!
Well, this is legacy material so I kinda forgot what TWRP worked best for the older ROMs (2.8?). The latest TWRP should be backwards compatible and support CM11 so you can give that a whirl first. You're just making a backup (no write actions) and TWRP's are easily replaced with other version so there ain't much to lose. Anyway, glad you got it running! I'd still go with the CM13 flash before moving to one of the modern ones. If you encounter more bootloops, that same exe should recover it for ya. By the way, can you PM me a link to that exe? Who knows, it might come in handy one day.
As a stable up-to-date ROM I can really suggest crDroid. I've been using it myself for a few weeks now. @chineel is a talented and devoted dev.
Timmmmaaahh said:
Heya!
Well, this is legacy material so I kinda forgot what TWRP worked best for the older ROMs (2.8?). The latest TWRP should be backwards compatible and support CM11 so you can give that a whirl first. You're just making a backup (no write actions) and TWRP's are easily replaced with other version so there ain't much to lose. Anyway, glad you got it running! I'd still go with the CM13 flash before moving to one of the modern ones. If you encounter more bootloops, that same exe should recover it for ya. By the way, can you PM me a link to that exe? Who knows, it might come in handy one day.
As a stable up-to-date ROM I can really suggest crDroid. I've been using it myself for a few weeks now. @chineel is a talented and devoted dev.
Click to expand...
Click to collapse
Try bacon root toolkit you can perform most of the things very easily.
chineel said:
Try bacon root toolkit you can perform most of the things very easily.
Click to expand...
Click to collapse
Hey man, thanks for pinching in. I'm personally not a fan of these toolkits as one can accidentally lock the bootloader and I prefer manual style because it's educational and you see more of what's going on. It's like I preferred DOS over Windows 3.11 back in the day. That's pretty much the same, right?... ?
Timmmmaaahh said:
Heya!
Well, this is legacy material so I kinda forgot what TWRP worked best for the older ROMs (2.8?). The latest TWRP should be backwards compatible and support CM11 so you can give that a whirl first. You're just making a backup (no write actions) and TWRP's are easily replaced with other version so there ain't much to lose. Anyway, glad you got it running! I'd still go with the CM13 flash before moving to one of the modern ones. If you encounter more bootloops, that same exe should recover it for ya. By the way, can you PM me a link to that exe? Who knows, it might come in handy one day.
As a stable up-to-date ROM I can really suggest crDroid. I've been using it myself for a few weeks now. @chineel is a talented and devoted dev.
Click to expand...
Click to collapse
Hi Mate,
My perils seem not to end.So after the last update I tried to start my phone and it started but as soon as I removed the power cord the phone switched off.
I realized that the issue was with the battery so I got it replaced in one of the OnePlus Authorized service center.
The new battery with only one month warranty started just fine and I could see the phone hold power without the charger attached.So I reached home and did the below
1)Flash Twrp
2)Flash CM 13 snapshot
3)Flash cdroid and gapps
4)Reboot phone
Everything seems to work as expected other than the goddamn network and the wifi.My phone has no IMEI and ofcourse I have no EFS backup stored cause of my previous fiasco.
Any ideas mate,I see forums where itts told to install color os and then cm11 and then something but I dont want to risk anything anymore .
Any advice ?
vedanth123456 said:
Hi Mate,
My perils seem not to end.So after the last update I tried to start my phone and it started but as soon as I removed the power cord the phone switched off.
I realized that the issue was with the battery so I got it replaced in one of the OnePlus Authorized service center.
The new battery with only one month warranty started just fine and I could see the phone hold power without the charger attached.So I reached home and did the below
1)Flash Twrp
2)Flash CM 13 snapshot
3)Flash cdroid and gapps
4)Reboot phone
Everything seems to work as expected other than the goddamn network and the wifi.My phone has no IMEI and ofcourse I have no EFS backup stored cause of my previous fiasco.
Any ideas mate,I see forums where itts told to install color os and then cm11 and then something but I dont want to risk anything anymore .
Any advice ?
Click to expand...
Click to collapse
you are going to have to use the colour os toolkit to get the imei info back there is nothing else you can do
---------- Post added at 05:34 PM ---------- Previous post was at 05:20 PM ----------
vedanth123456 said:
Hi Mate,
My perils seem not to end.So after the last update I tried to start my phone and it started but as soon as I removed the power cord the phone switched off.
I realized that the issue was with the battery so I got it replaced in one of the OnePlus Authorized service center.
The new battery with only one month warranty started just fine and I could see the phone hold power without the charger attached.So I reached home and did the below
1)Flash Twrp
2)Flash CM 13 snapshot
3)Flash cdroid and gapps
4)Reboot phone
Everything seems to work as expected other than the goddamn network and the wifi.My phone has no IMEI and ofcourse I have no EFS backup stored cause of my previous fiasco.
Any ideas mate,I see forums where itts told to install color os and then cm11 and then something but I dont want to risk anything anymore .
Any advice ?
Click to expand...
Click to collapse
you are going to have to use the colour os toolkit to get the imei info back there is nothing else you can do
kallum7 said:
you are going to have to use the colour os toolkit to get the imei info back there is nothing else you can do
---------- Post added at 05:34 PM ---------- Previous post was at 05:20 PM ----------
you are going to have to use the colour os toolkit to get the imei info back there is nothing else you can do
Click to expand...
Click to collapse
Mate ,can you please help me with the link ?
I know I can google it but I just dont want to take chances anymore
vedanth123456 said:
Hi Mate,
My perils seem not to end.So after the last update I tried to start my phone and it started but as soon as I removed the power cord the phone switched off.
I realized that the issue was with the battery so I got it replaced in one of the OnePlus Authorized service center.
The new battery with only one month warranty started just fine and I could see the phone hold power without the charger attached.So I reached home and did the below
1)Flash Twrp
2)Flash CM 13 snapshot
3)Flash cdroid and gapps
4)Reboot phone
Everything seems to work as expected other than the goddamn network and the wifi.My phone has no IMEI and ofcourse I have no EFS backup stored cause of my previous fiasco.
Any ideas mate,I see forums where itts told to install color os and then cm11 and then something but I dont want to risk anything anymore .
Any advice ?
Click to expand...
Click to collapse
I'd hate to say I told you so ?
Don't worry too much. The cool thing about flashing with Android is that there's always other ways to get to a working system. Plus, having a fizzled up system is how you'll learn the most about how this all works. You'll be a pro in no time. I personally got seriously into troubleshooting with a hard bricked OPO that had a wasted flash chip. Believe me when I say that's a whole other world of pain.
One question: did you wipe system/data/caches between the CM13 and the crDroid flash? That's kind of important. It would also be useful to mention the versions of everything.
I have no first person experience with broken EFS partitions but according to what I've read you'll indeed have to get ColorOS running. You could try wiping everything again and flash CM13 to see if that boots fine (with working connectivity) but I'm afraid you'll have to go through the whole works: wipe all, flash or fastboot flash ColorOS, get it running (verify IMEI), flash TWRP and backup EFS (MAKE AN EXTERNAL COPY), wipe all again, flash CM13, get it running, wipe all again, flash crDroid + Gapps, wipe caches and boot to a (hopefully) working system. If EFS broke again you can simply restore the backup made earlier instead of starting over.
Mind that when I say wipe all, it doesn't have to include internal memory or you'll be wiping backups you might need later on.
Alright, here goes your 27th attempt. Good luck! ?
mate here is the link https://forum.xda-developers.com/oneplus-one/general/guide-unbrick-oneplus-one-t3013732 even though it says do not use on soft brick devices in your case you are going to have to