Hi guys,
I've just gotten my G2 setup to overclock at 1.4GHz and I'm trying to set up some profiles so that it runs at around stock or just higher when it's on battery.
Problem I'm having is that the sliders for setting the frequencies won't let me choose anything in between!!
It only allows me to go from 768 straight up to 1401 but nothing in between!
Can anyone help at all?
Much appreciated!!
I'm currently using CM10.1 AOSP [KANG] from the thread here -- http://forum.xda-developers.com/showthread.php?t=2115520. In essence, I cannot raise either the minimum or maximum CPU speeds above 384MHz.
I just tried restoring my phone using a RUU recovery.exe file, then re-rooted, S-OFF'd, unlocked the bootloader and then updated the firmware. Right after flashing CM10.1, I am still having issues with changing the CPU speed. The maximum and minimum CPU speeds I can choose are either 192MHz or 384MHz. I can go into settings > performance then change the maximum CPU speed to anything higher than that, but almost instantly after I select it the maximum CPU speed drops back down to 384 MHz. The same goes for trying to raise the minimum CPU speed above 384MHz. It makes the phone nearly unusable, as it takes multiple seconds to open almost any application and also reboots randomly quite often. Is there any way I can fix this?
Thanks!
Anyone have ideas/insight? Sorry to bump this!
Right. Here's what I did last time. I used something called SetCPU. Ticked the Set On Boot then it worked. But I unticked the ones in the Performance option.
This is what I do. Hope I help.
if you want do this also
go to system>etc>init.qcom.post_boot.sh and put this line(you can edit with simple text editor)
echo the value > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
do the same for cpu1 if you want to have the same frequency in both cpu
hey everyone i just installed cm12.1 on my OPO. and i got some problems.
1. my cpu is only showing the cpu states 2.46, 2.27, 1.96, 1.73, 1.57. and deep sleep. all the other cpu states are not shown for me in betterbatterystats app. and when i check in rom toolbox pro my cpu sliders are both set to maximum ghz. and i did try to take the min freq slider to the minimum and set on boot, but it did not help. the sliders were still on max when i startet the app again and the same cpu states in BBS. i can't even see or find what would be the wakelock for this or something... it does go to deepsleep but when it is awake it is never showing the lowest cpu state 300 MHZ the lowest it goes to is 1.57 GHZ
2. sometimes when i shut down my phone it restarts by itself even though i tell it to shut of.
does any of you know anything about these problems? please help me! i really need help with this.
my samsung galaxy s4 on the ''same'' rom 10-24 is not having any of these problems. the cpu is normal and i haven't noticed any reboots when telling it to shut down.
any thoughts or answers are welcome
Hello,
Mi 4i lags/slows down most of the time, when i check CPU-Z during that time, i can see that only the lower clocked 2/4 cpu cores run constantly at 800 Mhz. It is very difficult to use when it is so slow. Other 4/6 cores remain inactive.
Is there any solution for this weird behavior while running in Balanced mode. Even when switching to Performance mode, nothing changes. I believe due to the heat generated, the OS automatically underclocks the CPU. I have already rooted and tried changing the CPU Governor, Clock speed but it resets to default every time. Sometimes i am unable to change that too.
Thank you.
There's a configuration that does this, just try to use the provided tweaks available here and then configure the phone's cores and so manually.
http://en.miui.com/thread-140563-1-1.html
I tried tweaking the thermal config using the above thread. But still only four cores are active @ 800 Mhz. The phone is so lagging that it is not usable at most of the time. Unable to change governor in any CPU clocking app, turn on the other cores. If you can help me out, please let me know.
Thanks.
Hackerpunk1 said:
There's a configuration that does this, just try to use the provided tweaks available here and then configure the phone's cores and so manually.
Click to expand...
Click to collapse
Might be a bug. Try a clean install and see
Same here
I am having a similar issue, very frustrating. I tried Sensei kernel, but no luck
i don't know what do you mean bro
everytime i change to other rom,other kernel
the results is...
all core is on
vijayr2002 said:
Hello,
Mi 4i lags/slows down most of the time, when i check CPU-Z during that time, i can see that only the lower clocked 2/4 cpu cores run constantly at 800 Mhz. It is very difficult to use when it is so slow. Other 4/6 cores remain inactive.
Is there any solution for this weird behavior while running in Balanced mode. Even when switching to Performance mode, nothing changes. I believe due to the heat generated, the OS automatically underclocks the CPU. I have already rooted and tried changing the CPU Governor, Clock speed but it resets to default every time. Sometimes i am unable to change that too.
Thank you.
Click to expand...
Click to collapse
strange, i am using miuipro with sensei and havent found any problem.
This happens in the latest stable MIUI7 ROM. I think it is time to change to a custom rom.
Hey guys, for some reason my CPU settings jump around on their own and I can't set the frequency. This happens on multiple apps. I have already disabled "per-app profiles" in the battery settings. The only apps I have installed that deal with the CPU settings are 3C Toolkit Pro and Kernel Aduitor. I've tried installing SetCPU and setting the frequency there doesn't do anything. Any idea why this is happening? I'm on a LG G3 running Resurrection Remix for 6.0.1.
Edit: I think it might have to do with the thermal driver. Is it possible that this is the case? It stopped doing the jumping for now, so maybe it's because it cooled off.