Related
it says- output :5v 500mah
the original says-output:5v 1a(amper i guess)
will this screw up the battery?
chances are no, considering it is half what htc recommends you charge it with, either it will charge it very slowly (half the current of the original) or the voltage wont provide enough to kick the phone into charging mode and nothing will happen (i.e. the charger "wont work")
Thanks for the help
It'll work, but as panyan said, it'll recharge much more inefficiently than with a 1 amp charger.
Actually... It will charge the phone exactly as charging via USB, as USB is limited to 0.5A.
Yep, it will charge your phone just fine @ USB charging speed, I have a similar charger.
And some of you forgot to mention that the phone will struggle when for example you will play games or use gps. Charge will be insufficient and instead charging it will slowly discharge while using it.
Sent from my Desire HD uing XDA App
Well yes and no, in normal usage it will charge phone, but when you use your phone the way that you would drain the batty in two hours, then it will discharge.
Hey... Yeah if the charger is a car charger then it may not charge fast enough if using GPS software which can drain the battery fast. 1Amp reccomended for faster charging... other than that should charge fine but just slow like USB charging (which has a max of 500mA).
One question guys... I bought a car charger from ebay listed as for HTC phones. It looks like a cheap knock off product with a glowing blue HTC logo when used in the car. The device is rated at 2Amps. Now from what little I know about electronics I've been told that AC/DC Plug packs with more Amps are ok and the device just only uses what it needs. I'm not however familiar whith battery charing when you have a higher rated Amps charger... Would the battery on the phone just be greedy and "ask" for the full 2Amps? Would this then put strain or be dangerous by charging the phone too quickly?
Secondly while we are on the topic of electronics... I'm trying out a super cheap ebay battery supposedly rated at 1600mAH (I know these rating are usually fake). I've noticed the HTC battery is around 4.17V when fully charged. This battery charged up to 4.2V fully charged... Is that dangerous for the device?
2 amp is better, correct me if i am wrong. So the output is 5V and 2A, is that mean the power is 10W every hour ?
2 A charging current (if the phone takes in that much) will damage the battery in a long term use.
It is incredibly unlikely that the phone will discharge the battery faster than it charges unless you're doing something very wrong, e.g. Running a console emulator while downloading a large file over HSDPA with WiFi enabled (but not connected) and using GPS navigation with screen brightness at maximum!
Screen and background services take approx 150mAh, and I doubt radio will take much more than that combined. That puts drain 200mAh less than USB charging, 700mAh less than direct charging.
FYI: There's a spec for USB charging of mobile phones from supported USB ports which can pull up to 1500mA.
DeathJester said:
It is incredibly unlikely that the phone will discharge the battery faster than it charges unless you're doing something very wrong, e.g. Running a console emulator while downloading a large file over HSDPA with WiFi enabled (but not connected) and using GPS navigation with screen brightness at maximum!
Click to expand...
Click to collapse
Hmm... not sure for Desire HD I haven't tested GPS with SatNav software using current widget... I do know that I'm pulling well over 200mA just with basic use at home with Wi-Fi on and GPS & Bluetooth off and I kill all backround apps. I do know that I've been in the car and seen TomTom app on my friend's jailbroken iPhone 3G (or 3Gs) and with the GPS on and not doing anything intensive... we were actually travelling down a long straight highway, the phone was chewing more battery than the car charger could charge, so he switched off GPS.
Ah also guys no need to worry about the 2Amp charger... It sh*t itself on the 3rd car use and no longer works at all. Junk! I also noticed on the 2nd car trip that opening Android SpareParts the charge is displayed as USB Charging not AC Charging so yeah I believe that the car charger was only a standard USB (max 500mA) power output and not 1Amp let alone 2Amps. Annoying how false advertising or labelling is part and parcel with cheap Chinese products.I was meaning to test the charger's output with Current Widget (which is what I'll do for my next car charger) but the charger crapped out and was useless before I got a chance.
One thing I did notice from looking at a log using Current Widget while charging my phone on the A/C charger in standby, the charge tapers off the power output the more the battery is charged. To get an accurate idea of if the car charger is going to be outputting 1Amp I'd be sure the phone battery is down to 40% (or in the 40s) then with all other stuff switched off I'd run a log on Current Widget and turn the screen off for a few minutes. You should have a reading of around +700 to +800mA if the car charger is rated at 1Amp.
Be wary of the cheap Asian knock of car chargers with the coil spring cord and the HTC logo that lights up blue.... Not worth the 3 or 4 bucks they sell on ebay for.
There's a spec for USB charging of mobile phones from supported USB ports which can pull up to 1500mA.
Click to expand...
Click to collapse
There's commonly those double USB cables for laptop hard drives so yeah I can see that if the USB ports are actually giving you the full rated maximum of 500mA you can get 1Amp output with this kind of cable but 1500mA?!? The only way I'd see possible for this is either you have a tripple USB cable connected to 3USB ports that are all outputting the full 500mA (and that's if a triple cable even exists or lets say you solder another one onto a double cable) or you have a USB AC/DC charger or some other USB port/hub you've rigged up which provides more than the USB standards of max 500mA per port. How else is this possible?!? Has the max power output of 500mA changed since USB 2.0 standards?
yeah there are usb 2.0 ports with more than 500mA power supply.
some companys give some extra juice to their (or often only one) usb ports.
for example: i've got an Dell Studio XPS 16 Notebook here. it has 3 usb ports, 2 with normal 500mA supply and one with 1A (for charging your phone, etc).
DN41
I've noticed that charging with 500mah charger, charges the battery MUCH slower than a 1000mah (1amp) charger, which charges really fast. I'll need to time it, but I'm thinking the 1000mah charger charges the stock battery in less than 2 hours, where as the 500mah charger takes many hours, I usually let it charge overnight.
My question is, is there any performance gain to slow charging vs fast charging? ie: slow charging giving a deeper charge, vs fast charging?
any opinions?
i use a 2amp charger i had already that fully charges the O3D in around half an hour/45 mins. get the same runtime whether i use that or the stock charger.
hefonthefjords said:
i use a 2amp charger i had already that fully charges the O3D in around half an hour/45 mins. get the same runtime whether i use that or the stock charger.
Click to expand...
Click to collapse
Any chance of a link to this charger, I'd really like that sort of charging speed.
Pete
My guess would be anything that would charge an iPad... those require like 2.1amp, so that would be a 2amp usb charger.... I've seen 2.1amp home chargers, car chargers, etc... all because of the ipad I'm guessing.
Its not that simple. Any device that uses USB for charging can only pull 500ma, that's a universal agreement. To get around this each manufacturer uses a method of "informing" their device that it is connected to a charger that can supply more current (HTC shorts the data leads in the supplied charger I don't know what LG does). I have a 1amp car charger but it still only gives 500ma but the genuine LG charger gives an amp because the phone "knows" it can supply more.
I'm going to stick a test meter into my LG chargers over the holidays to see how the data leads are connected.
Pete
Sent from my LG-P920 using xda premium
The charger i have is a noname brand. I bought it from walmart for 6 quid. It also came with a 2amp car charger and a micro usb cable.
Micro usb cables are not standardised like that. Ive never heard of such a thing at all. As far as i know most phones will "fast charge" if they dont detect a data connection and dump as much current as they can into the battery so you can pretty much present them with whatever current you like and the charge time will just get faster. There is probably a hardware limit to that somewhere in the charge circuit but i dont know what the limit is. 2amps is the highest power usb charger ive seen but its not exactly aomething i regularly keep an eye out for.
Sent from my LG-P920 using xda premium
Slow charging is always better as this will allow the optimal number of battery cycles before the battery's capacity will start to degrade.
So if you only ever slow charge then your battery will have a longer life cycle.
I lost my wall charger that came with my HP touchpad. The round plug thingie is what I'm looking for. Searching on Amazon brings up a number of items, for example:
http://www.amazon.com/HP-North-American-Charger-TouchPad/dp/B0055QYJJM/ref=dp_cp_ob_e_title_3
However, is there an alternative that works? I was able to use the Evo cable rather than the original HP sync/charge cable that came with the wall charger, but is there an alternative wall plug that works as well? Paying almost $28 for a charging cable seems a bit ridiculous.
Any help and advice would be most appreciated.
[[FOUND MY ANSWER]]
I found that Walmart was having a sale on the North American charger with the barrel wall connector for $11.99 and Meritline was having a sale for 6' long USB to micro-usb cables (pair for $4.99 no tax/shipping).
The listing on the Meritline page says that the cables are compatible with the Evo.
Given that the cable that comes with the HP barrel charger is pretty much monkey spit and fails within a month, I found a solution that works for less than $20.
Links are below:
Walmart HP Touchpad charger
http://www.walmart.com/ip/HP-TouchPad-Accessory-Travel-AC-Wall-Adapter-Charger/16641536
Meritline Cables (use this code MLCK222YNL1 for discount (cannot guarantee how long this code is good for, drops the price for a twin pack of the 6' cables from $10.99 to $4.99)
http://www.meritline.com/showproduc...e=6-feet-high-speed-micro-hdmi-cable-ethernet
Pretty much any USB charger will work, but most give a notification on the Touchpad screen indicating that they may not be charging. This is because the official charger is at the high end of both voltage and current capability. I charge from laptop, desktop and a variety of Blackberry chargers with no issue, but the available current will determine how long it takes to charge and whether it charges much while the screen is on. Go for a USB charger that gives you 2 Amps and you should be fine.
dmarchant said:
Pretty much any USB charger will work, but most give a notification on the Touchpad screen indicating that they may not be charging. This is because the official charger is at the high end of both voltage and current capability. I charge from laptop, desktop and a variety of Blackberry chargers with no issue, but the available current will determine how long it takes to charge and whether it charges much while the screen is on. Go for a USB charger that gives you 2 Amps and you should be fine.
Click to expand...
Click to collapse
Thank you for the advice. To be more specific, can you recommend any alternative charging cables/wall charger units specifically?
Any brand name USB charger that gives off 2 amps should be fine. I tend to stay away from really cheap generic chargers. Any microUSB cable should be fine even a generic one if it has decent reviews. I worry about generic chargers since a poorly regulated one could send a voltage too high, but generic cables should be fine.
The chargers I am currently using, as well as the one that came with the TP, are the one that came with a Blackberry Playbook and the one from my HTC Desire HD.
The Blackberry charger gives an error on the screen that it may not charge the TP, but as it gives 2 amps, charges in pretty much the same time as the official unit.
The HTC again gives the warning and takes about twice as long to charge.
what about the nook color charger i know it higher amps might work as well
cesar2010 said:
what about the nook color charger i know it higher amps might work as well
Click to expand...
Click to collapse
I just tested the TP with a charger for the NC, and unfortunately, it still gives the same "may not charge" warning...
There is NO after market charger that will charge at full rate like the HP barrel charger!
At best they will trickle charge at a much lower rate and take considerably longer to charge.
The TP relies on precise signaling which it will only get from the OEM item or specially modded after market units or cables.
Do a google for further info ie webosnation.com forums.
I think your looking for a 5.1v charger, aka rapid charger. This is used by the iPad, and some android phones like the Motorola droid 3, razr and htc rezound.
I could be wrong though,I haven't gotten my touchpad yet.but I do own all said device above (except the razr) and they all use the faster charging technology.
Sent from my rezound.
Izeltokatl said:
I think your looking for a 5.1v charger, aka rapid charger. This is used by the iPad, and some android phones like the Motorola droid 3, razr and htc rezound.
I could be wrong though,I haven't gotten my touchpad yet.but I do own all said device above (except the razr) and they all use the faster charging technology.
Sent from my rezound.
Click to expand...
Click to collapse
They will not work at full rate!
No one else uses 5.2 volts
Sent from my Samsung Galaxy S2
Don't believe all the hype about using ONLY the HP charger, there are many that do the job perfectly well. Too many people make these authoritarian statements and all they do is cause FUD.
At my office, I use the AC charger from my last Samsung phone (mythic) and it works IDENTICALLY to the OEM one. I have also used a Moto and and LG with NO PROBLEMS. I have no issues getting to fully charged in little time.
At home, my OEM cable is plugged into a high-power USB port (2.1A, I believe) and it has no problem charging from near zero to full as well. Front or top-mounted USB ports tend to be 500mA or less, but the rear ones (coming directly off the motherboard) tend to have a higher supply. I also use a non-HP USB cable occasionally and it works fine.
(I got my TP during the original fire-sale and have been charging it these ways ever since with ZERO ISSUES.)
R1ptide said:
No one else uses 5.2 volts
Sent from my Samsung Galaxy S2
Click to expand...
Click to collapse
The small voltage difference is marginal and isn't going to matter, the internal hardware should be able to tolerate a few tenths of a volt difference. In fact, I tested my Motorola charger rated at 5.1v and the Touchpad charger rated at 5.2v on a multimeter. The Motorola charger was outputting 5.20v and the Touchpad charger 5.16v. Granted this is at no load, but switching transformers are regulated so they should supply rated voltage at any current draw equal to or less than rated. Also depending on how well the voltage is regulated there may still be a slight AC ripple that the device has to deal with.
Does anyone know the time difference between using the TP charger and a standard droid/blackberry charger? Also curious if the charges last the same. I know theoretically they should since the battery is full either way, but electricals can be tricksiy..
sirclesam said:
Does anyone know the time difference between using the TP charger and a standard droid/blackberry charger? Also curious if the charges last the same. I know theoretically they should since the battery is full either way, but electricals can be tricksiy..
Click to expand...
Click to collapse
Its all down to the charge rate that the TP is able to draw.
2A which is theoretically possible from TP AC barrel charger would charge the 6A+ battery of the TP from flat to full in approximately 6.5 hours.
If the BB charger were able to have 500mA drawn by the TP then it would fully charge in approximately 26 hours.
The charges would be no different.
To convert any regular USB charger into a TouchPad charger you need to add 2 resistors as per the diagram attached.
The presence of the resistors will trigger the TouchPad to draw the full 2A from the charger rather than the trickle charge it does when they are not there.
Please do not modify a cheap charger that is only rated for 500mA as you will most likely overheat it and it could present a fire risk.
stuart_f said:
To convert any regular USB charger into a TouchPad charger you need to add 2 resistors as per the diagram attached.
The presence of the resistors will trigger the TouchPad to draw the full 2A from the charger rather than the trickle charge it does when they are not there.
Please do not modify a cheap charger that is only rated for 500mA as you will most likely overheat it and it could present a fire risk.
Click to expand...
Click to collapse
Just pointing out that you need to start with a charger that is rated at least 2Ah to start with.
You can't turn a low rated one into a high rated one.
pa49 said:
Just pointing out that you need to start with a charger that is rated at least 2Ah to start with.
You can't turn a low rated one into a high rated one.
Click to expand...
Click to collapse
oh, for the love of gods. REALLY? I was just asking for a replacement cable. I don't want to reinvent the charging paradigm. I just need a simple recommendation for a cable. If a thread could be highjacked any further I don't know how it could be.
I appreciate all your "advice" but seriously, this is NOT what I was asking.
Anyone know if I can get a similar cable in the UK? Kind of lost my TP cable, and I miss the flexibility the long cable gave me, it was so much easier to use on charge!
well i know that my tbolt cable works. i have to use the tp adapter though. my tbolt adapter makes the touchpad say that the charger is incompatible.
Hi,
Wanted your thoughts and opinions on charging speeds. I've never actually timed how long it takes to charge. i leave it overnight and it's ready when i wake up.
When i plug the phone into the charger, it flashes up slow charging for 2 seconds then disappears. which got me wondering how much it's actually using.
i used to use Current Widget app on my Samsung S3 which told me exactly how much current the phone was taking from the charger. typically it was 1A via AC/mains and 499mA from a PC. Plugged in to AC, I could play a power hungry game and it would still charge the phone at a good rate.
The LG kernel doesn't like these apps - the mA value is all over the place but it's typically <500mA displayed.
I could buy a USB ammeter to work out how much the USB charger is supplying but do you have any other methods of finding out? Do you know what your phone uses?
at home, i use a Xtrememac dual USB charger, 2x 2.1A output with a shielded 3M USB cable. for those wondering, it's the same regardless what cable i use. Have also tried with generic usb chargers, iPad chargers and official and OEM cables from LG and various other manufacturers. Have also used a data-shorted USB cable from PC which is the same result.
I haven't tried the LG charger yet (mainly as it's a 2 flat-pin plug and i don't know where i put the box) but i think i recall it being a 1.8A charger.
I use an application called "charger report" which can display current consumption and Xtar "USB detector" device. They both show the same numbers. But Xtar USB detector can detect voltage of a charger. The charging current of LG g pro 2 is 1.4-1.5A when the smartphone is not used and higher when I use it. Using USB detector I found out that this smartphone can charge with maximum current a charger can give only if the charger's voltage is 5.3v. So it chargers at full speed with original charger and two other chargers I have: a charger from my Lenovo s6000 (2A 5.4V) and from my Asus t100 (2A 5.3V).
i tried that app too and got the same results as with Current Widget.
i'll buy a "usb detector". thanks.
I forgot to mention that it take approximately two hours for charging indicator to reach 100% when the smartphone reports that it fully charged. And it's necessary to left it connected to a charger for ten to twenty minutes to be really fully charged. Otherwise charging indicator will soon drop to 90%. One can tell if a smartphone is still charging by touching a charger or by looking at current consumption: a charger would be warm and current would be higher than 200mA.
Is the GP2 Quick Charge (1 or 2) enabled? I can't read anything about it other than it's in Snapdragon chipsets. Not sure if it can be disabled or not.
ray-lee said:
Is the GP2 Quick Charge (1 or 2) enabled? I can't read anything about it other than it's in Snapdragon chipsets. Not sure if it can be disabled or not.
Click to expand...
Click to collapse
The Snapdragon 800,801 and 805 is for Quick Charge 2.0
The Snapdragon 600 for 1.0
ok, does anyone use a Quick Charger with their GP2? is it noticeably faster?
not yet available in Austria, I have read it kills the battery life on
ray-lee said:
Hi,
Wanted your thoughts and opinions on charging speeds. I've never actually timed how long it takes to charge. i leave it overnight and it's ready when i wake up.
When i plug the phone into the charger, it flashes up slow charging for 2 seconds then disappears. which got me wondering how much it's actually using.
i used to use Current Widget app on my Samsung S3 which told me exactly how much current the phone was taking from the charger. typically it was 1A via AC/mains and 499mA from a PC. Plugged in to AC, I could play a power hungry game and it would still charge the phone at a good rate.
The LG kernel doesn't like these apps - the mA value is all over the place but it's typically <500mA displayed.
I could buy a USB ammeter to work out how much the USB charger is supplying but do you have any other methods of finding out? Do you know what your phone uses?
at home, i use a Xtrememac dual USB charger, 2x 2.1A output with a shielded 3M USB cable. for those wondering, it's the same regardless what cable i use. Have also tried with generic usb chargers, iPad chargers and official and OEM cables from LG and various other manufacturers. Have also used a data-shorted USB cable from PC which is the same result.
I haven't tried the LG charger yet (mainly as it's a 2 flat-pin plug and i don't know where i put the box) but i think i recall it being a 1.8A charger.
Click to expand...
Click to collapse
Hey ray-lee!
I just bought this phone and as it seems it could get someday similar problems as my former phone the Galaxy Note 2.
That phone has had problems with charger and cable also. I had to buy another set of charger and cable since the original ones gave up a few months after i purchased the phone (it was used). The cable managed only 500mA wich is very slow for a battery that strong. One night was once not enough to charge my phone from 30% to 100%. As it seems it is problematic to manufacture cables, that can hold up and continually grant the 1,8 A that would charge our device in just 2 hours. I read somewhere that the G Pro 2 is one of 5 devices that has blazing fast speeds on charging the battery. If you handle the cables with caution hopefully you will not encounter problems. If so my guess is, that you will have a hard time in finding a cable that can hold up. Sadly the stock cables are always more expensive. I do not get it, why companies dont build travel adapters that only charge ur phones built solid with sturdy cables to ensure the transmission of high currents. That way with charger + usb cable is just stupid, even when tis is an all in one solution.
I like this phone very much and i hope, that the cables will not be that sloppy as the cables that Samsung had/ still has. With Current Widget i get readings around 1500 mA (1,5 A) when connected to the stock charger. And yes the LG Charger is an 1,8 A one. I have also flat pins, but received an adapter to be able to connect it in Hugary.
Just sharing thoughts here, that will maybe helpful to someone...
:highfive:
2amp charger, charges my Pro 2 in apprx 1 hour while my old LG 1amp charger fills it in 1.40 hours apprx
ray-lee said:
Is the GP2 Quick Charge (1 or 2) enabled? I can't read anything about it other than it's in Snapdragon chipsets. Not sure if it can be disabled or not.
Click to expand...
Click to collapse
i "think" as long as device has snapdragon it is Quick Charge enabled
I use the "Charging Report" app on my phone, and it reports proper values.
(Around 1500mAh with the LG charger, and around 1600mAh with the 2.0A Samsung charger.)
If your phone is charging slowly, check the CABLE. Cable can broke too.
(Many people complain about their Samsung charging cables, because they just stop delivering power after a while and just charge the device slowly.)
Anyone tried Quick charge 2.0?? https://www.qualcomm.com/products/snapdragon/quick-charge
enkhtwshn said:
Anyone tried Quick charge 2.0?? https://www.qualcomm.com/products/snapdragon/quick-charge
Click to expand...
Click to collapse
All Devices with the Snapdragon 800 have Quick Charge 2.0!
letschky said:
All Devices with the Snapdragon 800 have Quick Charge 2.0!
Click to expand...
Click to collapse
So anyone tried it? That is the question
Yes, I have the Motorola Turbo Charger.
coastalmikey said:
Yes, I have the Motorola Turbo Charger.
Click to expand...
Click to collapse
How long does it charge from 0-50 from50-100 from 0-100?
There aren't many chargers out there. and the ones that are, are usually US 2 pin. I need a UK 3 pin or travel charger (changeable pins) really.
enkhtwshn said:
So anyone tried it? That is the question
Click to expand...
Click to collapse
To achieve full charging speeds, a Quick Charge 2.0 enabled device must be paired with a Quick Charge 2.0 certified adapter
My g flex 2 H959 cant charge while playing games, for example like temple run or even old nokia games like snakes 97?! it will actually drain the battery while charging if i use a SAMSUNG charger and it gains around 1 percent per 5 minutes if i use my LG FAST CHARGING charger, so the question is why lose so much when you play such light games.
my note 4 never did this!
john islam said:
My g flex 2 H959 cant charge while playing games, for example like temple run or even old nokia games like snakes 97?! it will actually drain the battery while charging if i use a SAMSUNG charger and it gains around 1 percent per 5 minutes if i use my LG FAST CHARGING charger, so the question is why lose so much when you play such light games.
my note 4 never did this!
Click to expand...
Click to collapse
off topic: yellow on white? are you kidding me/us?
on topic: in Games the GFlex2 use the whole Power of the Snapdragon 810 and maybe the GFlex2 is not optimized for playing Games, can be, but you can help your battery:
turn down the brightness, root your phone and use Greenify and disable or delete bloatware and useless google stuff, force your SD 810 to a lower frequency and so on
john islam said:
My g flex 2 H959 cant charge while playing games, for example like temple run or even old nokia games like snakes 97?! it will actually drain the battery while charging if i use a SAMSUNG charger and it gains around 1 percent per 5 minutes if i use my LG FAST CHARGING charger, so the question is why lose so much when you play such light games.
my note 4 never did this!
Click to expand...
Click to collapse
You can try if you dont already custom thermal settings from user probaina.
It's your usb cable!
The cable quality is very important. Even if you have a good 5V charger, it's useless with a slim and long cable.
The more resistance (ohm) there is on your cable, the more intensity you will lose (A). And the resistance goes by two factor, cable thickness (AWG in USA and mm² elsewhere) and cable lenght. The thinner and the more lenghtful is the cable, the less Amp will go thru.
I have a usb voltmeter and ampmeter so I can give a value on each scenario.
I have a usb charger that can deliver 2.1A and 5V. With a normal cable that was bundled with blackberry (I got them at work) I get 690mA. Cable is 1.2m long and 28AWG is marked on the cable.
With the same charger and a 50cm long cable and 28/22AWG gauge (I suppose it's 28AWG for the data cable and 22AWG for the charging cable), I get 1.29A
With a 3m cable (yes it's long but I have a purpose for it) of unknown gauge, I get 250mA, sometime 300mA maximum. And this intensity it's just a little more than 1W. Even overnight I lose battery percentage.
But with the LG Fast Charger it's all different. It's not labeled Qualcomm Quick Charge 2.0 because it don't deliver 12V. The LG charger deliver 5V and 9V while Qualcomm spec for QC2.0 must be with 12V too. Anyway lets say it's a quick charge 2.0 charger because it act like one.
With the LG charger, with the 3m cable, I have 8.2V and 1.2A which is nearly 10W, more than enough to play and charge at the same time.
I can explain why the 9V tension help with the high resistance of the cable but to make it short it's the same as the big high tension cable in country side, the high voltage help for the long distance even if there is very big cable.
The usb cable provided with the Flex 2 is very good, it's 20AWG on the charging pair. But if you can find shorter cable it's even better (Western Digital cable is very good but to find one of their device bundled with a short and tick WD cable that is not mini usb and not usb 3.0 is very hard).
If you want the fastest charging speed you have to buy a QC2.0 certified charger and a 22AWG or 20AWG short cable. For daily charging I recommand using your old 5V charger (your samsung one).
Thank you so much for this answer bro
Le_Zouave said:
It's your usb cable!
The cable quality is very important. Even if you have a good 5V charger, it's useless with a slim and long cable.
The more resistance (ohm) there is on your cable, the more intensity you will lose (A). And the resistance goes by two factor, cable thickness (AWG in USA and mm² elsewhere) and cable lenght. The thinner and the more lenghtful is the cable, the less Amp will go thru.
I have a usb voltmeter and ampmeter so I can give a value on each scenario.
I have a usb charger that can deliver 2.1A and 5V. With a normal cable that was bundled with blackberry (I got them at work) I get 690mA. Cable is 1.2m long and 28AWG is marked on the cable.
With the same charger and a 50cm long cable and 28/22AWG gauge (I suppose it's 28AWG for the data cable and 22AWG for the charging cable), I get 1.29A
With a 3m cable (yes it's long but I have a purpose for it) of unknown gauge, I get 250mA, sometime 300mA maximum. And this intensity it's just a little more than 1W. Even overnight I lose battery percentage.
But with the LG Fast Charger it's all different. It's not labeled Qualcomm Quick Charge 2.0 because it don't deliver 12V. The LG charger deliver 5V and 9V while Qualcomm spec for QC2.0 must be with 12V too. Anyway lets say it's a quick charge 2.0 charger because it act like one.
With the LG charger, with the 3m cable, I have 8.2V and 1.2A which is nearly 10W, more than enough to play and charge at the same time.
I can explain why the 9V tension help with the high resistance of the cable but to make it short it's the same as the big high tension cable in country side, the high voltage help for the long distance even if there is very big cable.
The usb cable provided with the Flex 2 is very good, it's 20AWG on the charging pair. But if you can find shorter cable it's even better (Western Digital cable is very good but to find one of their device bundled with a short and tick WD cable that is not mini usb and not usb 3.0 is very hard).
If you want the fastest charging speed you have to buy a QC2.0 certified charger and a 22AWG or 20AWG short cable. For daily charging I recommand using your old 5V charger (your samsung one).
Click to expand...
Click to collapse
The thing is i have no complaint otherwise, my lg charger is pretty blazing fast with no games, its like 1 percent per minute fast, but as soon as i play games everything is lost and worsened!
thank you though for your answer. May Allah guide you to islam!
bro i cant root, its 5.1.1 no root has ever been discovered
kutulu32 said:
You can try if you dont already custom thermal settings from user probaina.
Click to expand...
Click to collapse
thanks though for your contribution. May Allah guide you to Islam insh Allah as you seem like a nice person!
john islam said:
The thing is i have no complaint otherwise, my lg charger is pretty blazing fast with no games, its like 1 percent per minute fast, but as soon as i play games everything is lost and worsened!
Click to expand...
Click to collapse
What you describe is different from the original post.
First you said that with a 5V charger (samsung) you lose percentage while playing but it was ok with the LG 9V charger.
then you say while answering to me that even with the LG charger you lose percentage but even if your cable is crap, the LG Fast Charger deliver enough power for any situation.
So you really lose percentage while playing with the LG Fast Charger?
And please, no proselytism.
Le_Zouave said:
What you describe is different from the original post.
First you said that with a 5V charger (samsung) you lose percentage while playing but it was ok with the LG 9V charger.
then you say while answering to me that even with the LG charger you lose percentage but even if your cable is crap, the LG Fast Charger deliver enough power for any situation.
So you really lose percentage while playing with the LG Fast Charger?
And please, no proselytism.
Click to expand...
Click to collapse
nope but with the lg charger it charges at around 5-8 mins for 1 percents, excuse me but that is wrong , it shouldnt
you meant it's not fast enough or too fast? I don't get your point.
If it's not fast enough, then do not use the phone while it charge or get a Quick Charge 2.0 charger that can do 12V.
If it's too fast, roll back to a 5V charger.
I was always under the impression that it is really bad for the battery to use the phone while it's charging. Perhaps just plug it in and let it charge while not using it is the best solution to charge faster.
I tried a Quick Charge 2.0 charger. The one supplied with our Flex 2 is not a QC 2.0 because it's only 5V and 9V. It still use QC 2.0 spec as at first it's 5V and when it identify the device it deliver 9V but it's not QC 2.0 certified as it don't deliver 12V.
So with a QC 2.0 charger, it deliver 9V too to the Flex 2. That mean that even if the S810 is capable of 12V charging, it's up to manufacturer to specify how it works. It won't charge at 12V.
I don't have another recent snapdragon to test the 12V.
Same!!!
I know its not good for batteries to be used while charging, but for example, i also have a Moto G and its okey playing while its connected to an outlet.
But with my Flex 2 its different, it charges incredibly slow, and worse... it gets HOT! REALLY HOT!
I'm trying now the thermal adjustments suggested by probaina.
Hope it works.
I'm going crazy...
What? My ATT version charges incredibly FAST! Sometimes it gets warm, but nothing I would be concerned about and it's even less after 5.1.1 update. Heck, my M8 gets just as warm if not more.
LMELME83 like OP you have to clarify things, is it slow to charge with a normal 5V charger (like the charger from your old phone) or is it also slow to charge with the charger provided, the LG Fast Charger?
For the 5V charger, the usb cable make all the difference.
For the LG Fast charger or a Qualcomm Quick Charge 2.0 charger, it's all about if the charger recognize your phone and there is no way to tell it on the charger or the phone. You have to use a usb voltmeter. I can recommand one that can take 12V.
Anyway it's normal that the LG G Flex 2 get warmer than the Motorolla Moto G (regardless of the generation because there is 3 or 4 different moto G). Any entry level phone will be colder, like a Core i3 will be colder than a Core i7 even if no one is crazy enough to use a core i7 with the stock heatspread and fan.