So I decided to try to flash Zombie-Pop today and everything went fine during installation but when the tablet started booting up it was stuck on "android is starting.." and it seems to load the apps. I knew it would take a bit of time to stabilize so I let it run but after 1 hour of it stuck there, I tried to reboot into recovery but I get a black screen and I can't access TWRP. It just boots right back to the android is starting screen. It doesn't seem to be a boot loop since it finishes the boot sequence. My biggest problem is not being able to access recovery because of the black screen which apparently is happening to some people with TWRP. I tried to go through adb but since my tablet isn't done installing, it doesn't have the drivers to run adb. Is my tablet toast? bricked?
edit: apologies for the title. I must have deleted the text before posting.
agentkalaw said:
So I decided to try to flash Zombie-Pop today and everything went fine during installation but when the tablet started booting up it was stuck on "android is starting.." and it seems to load the apps. I knew it would take a bit of time to stabilize so I let it run but after 1 hour of it stuck there, I tried to reboot into recovery but I get a black screen and I can't access TWRP. It just boots right back to the android is starting screen. It doesn't seem to be a boot loop since it finishes the boot sequence. My biggest problem is not being able to access recovery because of the black screen which apparently is happening to some people with TWRP. I tried to go through adb but since my tablet isn't done installing, it doesn't have the drivers to run adb. Is my tablet toast? bricked?
edit: apologies for the title. I must have deleted the text before posting.
Click to expand...
Click to collapse
Which bootloader are you on?
How are you trying to boot to recovery?
Related
So ive been running CM 10.1 with CWM v6.0.4.3 for several months without major issue until last night. I went to send a text message to someone, and right as i went back to my home screen, the phone froze, rebooted, and when it finished rebooting, the deice would freeze again as soon as the lock screen was reached, and reboot again. Cue repeated circle of freeze, reboot, finish rebooting, freeze, reboot.
I turned the phone off by taking out the battery, put it back in and charged it overnight without booting it up. Went to start the phone today, same issue still. I would boot into recovery and try to re-flash the OS, and it would give me a status 7 error. After re-downloading everything into my sd card, i was eventually able to get the system to re-install cm10.1.3, and it booted up normally. I downloaded and installed ROM Manager, and installed the newest version of CWM Touch, version 6.0.4.5, and then tried to boot into recovery to install CM11. It showed the CWM Hat icon in the middle of the screen, with the version on the bottom of the screen, then rebooted on its own without showing any menu options.
Now if i try to boot into recovery, it just shows the icon and version again, then reboots, and wont go past the CM loading screen with the spinning cyanogenmod icon.
Not sure what to do at this point, i cant get into recovery to try and flash something new, and i cant get past the CM loading screen to actually use my phone. Any ideas? I have zero experience with adb, so im stumped.
UPDATE: Solved, i flashed TWRP over CWM using Odin, and was from there able to re-install the OS. Things seem to be working fine for the most part, with the exception of one random reboot last night.
Salomon3068 said:
So ive been running CM 10.1 with CWM v6.0.4.3 for several months without major issue until last night. I went to send a text message to someone, and right as i went back to my home screen, the phone froze, rebooted, and when it finished rebooting, the deice would freeze again as soon as the lock screen was reached, and reboot again. Cue repeated circle of freeze, reboot, finish rebooting, freeze, reboot.
I turned the phone off by taking out the battery, put it back in and charged it overnight without booting it up. Went to start the phone today, same issue still. I would boot into recovery and try to re-flash the OS, and it would give me a status 7 error. After re-downloading everything into my sd card, i was eventually able to get the system to re-install cm10.1.3, and it booted up normally. I downloaded and installed ROM Manager, and installed the newest version of CWM Touch, version 6.0.4.5, and then tried to boot into recovery to install CM11. It showed the CWM Hat icon in the middle of the screen, with the version on the bottom of the screen, then rebooted on its own without showing any menu options.
Now if i try to boot into recovery, it just shows the icon and version again, then reboots, and wont go past the CM loading screen with the spinning cyanogenmod icon.
Not sure what to do at this point, i cant get into recovery to try and flash something new, and i cant get past the CM loading screen to actually use my phone. Any ideas? I have zero experience with adb, so im stumped.
Click to expand...
Click to collapse
You can try to reflash CWM with Odin, if that not working, you could try to Odin back to stock.
buhohitr said:
You can try to reflash CWM with Odin, if that not working, you could try to Odin back to stock.
Click to expand...
Click to collapse
I figured it out yesterday actually and forgot to update! Indeed I was able to flash TWRP with odin, since CWM seemed to be blocking me from doing anything. Once that was up and running, things went back to normal, i was able to flash CM 10.2.1 and things seem to be working now.
One thing though, while playing skyrim last night i had it on the charger next to me, and the phone randomly rebooted without any interaction from me. Was odd, but it hasnt done it since. Keeping an eye on it still.
I have looked at multiple guides on this and other sites, googled and tried stuff and I cannot resolve this problem. Hopefully I am posting in the right place.
I took the jump and unlocked the bootloader on my Moto G first generation, XT1034 successfully. I flashed TWRP 2.8.60.xt1034.zip with adb and this was successful. Then I flashed Super SU 4.6 Update and that was successful. I got into trouble I guess when I tried to flash Cyanogenmod 12.1 nightly. I used TWRP to flash via install. The flash had an error, which unfortunately I didn't write down. I believe it was something to do with a partition. However, it looked like the flash failed. At this point and for hours I have been trying to fix the "Warning Bootloader Unlocked Loop I am stuck in.
I have been able to get into the phone and flash via adb commands. I've tried several commands suggest to fix this that I have found in forums. I have tried flashing several recoveries including an older TWRP per the method in this thread, a clockworkmod - and the original 2.8.6.0.xt1034. When I get into the phone bootloader which is available, I have not been able to access any options in recovery. Pushing the power button on recovery leads to a blank screen sometimes followed by a recovery starting or a Motorola Logo starting up and a couple times a recovery. TWRP has started a couple times, but never gets past the intro screen, where it locks up. clockworkmod (clockworkmod-6.0.4.7-falcon.img started once after flashing through adb and gave me flash options. I tried to sideload, didn't understand, went back and the recovery locked up. These recoveries no longer load at all.
Through all of this the "Warning Bootloader Unlocked" logo screen comes up after plugging into the computer (Windows 8.1).
Example, I open the phone bootloader by waiting for the phone screen to go from the "Warning Bootloader Unlocked" screen to blank - it cycles from logo to blank. If I'm quick the phone and hard boot the phone will boot into bootloader. I connect to the laptop through USB. When I toggle to recovery and hit the power button the screen goes blank, the Motorola Logo pops up, goes blank and then the "Warning Bootloader Unlocked" appears. The Laptop then seems to connect and disconnect as the Warning screen comes on and turns off.
The factory selection just goes to a blank screen.
I would really appreciate some advice on how to get the phone back to a state in which I can work with it and try again. It is very difficult wading through all of the information out there. I've learned a lot through this issue, but can't take it any further.
Thanks, Jeff
Solved - Stuck in "Warning Bootloader Is Unlocked" Loop
This resolution took many hours to figure out, but I finally got there with this guide - http://forum.xda-developers.com/showthread.php?t=2542219, this thread - http://forum.xda-developers.com/showthread.php?p=54855457#post54855457 and this thread - http://forum.xda-developers.com/gen...e-firmware-t3042687/post59139823#post59139823.
I tried RSD Lite on different computers and USB cables I could not get the device recognized. So I ended up with the MfastbootV2 method to reload stock firmware, which I found on the firmware thread above - this was big, as my phone is with Wind Mobile in Canada and the link is the right one. The only thing I picked up from a different website was to use a computer with USB 2 ports. This is what I did, but I don't know one way or the other if USB 2 was needed. .
Can't thank you hard working guys enough for the time you take to put these threads together. I'm back up and running. As a bonus, after a big clean up in the process, my phone is running fast again.
Thanks everyone.
Hello,
I bought a new device and therefore wanted to factory-resent my Nexus 5 to give it to my wife.
I did it from within Android and then it restarted and stayed in the "Erasing..." screen for quite a while, then showed the dead robot with the "!" triangle sign, then rebooted and started "Erasing..." again, with apparently no way out.
I had unlocked bootloader and TWRP, but also booting the recovery went back into "Erasing..." mode.
I then tried to boot from an external TWRP iso image with fastboot from the PC. TWRP seemed to load, then started doing a bunch of things like formatting "something" (was too quick to read) and suddenly in a matter of second it was back to the robot but now without the "Erasing..." label anymore and now it's stuck there.
No idea what happened and how to fix and now I'm somewhat scared of trying something else.
Any idea?
Never mind... Flashed ALL stock images from fastboot (just userdata and cache didn't work) and it rebooted.
No idea what the problem was.
Hi all, have a rooted OPO that was running ExodusOS. I decided to try a flash of Lineage and so booted into recovery, backed everything up, flashed it. Everything seemed to go okay but after the boot logo the screen just goes black and stays that way until it gets shut back off. I went back to TWRP, loaded my backup and all seemed well as I was still able to use my old backup just as normal. Well, I tried reflashing Lineage from TWRP again and I still get the same black screen issue. This time, however, the phone will neither boot into Fastboot nor into recovery mode and just goes straight into loading Lineage. Because of this I am left with a soft brick until I can get this straightened out. I tried connecting the phone to my PC but it is not detected as a device. I only need to boot into my backup one more time so that I can back everything up, so even if it's only a temporary fix, I'm okay with that too. Any suggestions?
AMpageg2 said:
Hi all, have a rooted OPO that was running ExodusOS. I decided to try a flash of Lineage and so booted into recovery, backed everything up, flashed it. Everything seemed to go okay but after the boot logo the screen just goes black and stays that way until it gets shut back off. I went back to TWRP, loaded my backup and all seemed well as I was still able to use my old backup just as normal. Well, I tried reflashing Lineage from TWRP again and I still get the same black screen issue. This time, however, the phone will neither boot into Fastboot nor into recovery mode and just goes straight into loading Lineage. Because of this I am left with a soft brick until I can get this straightened out. I tried connecting the phone to my PC but it is not detected as a device. I only need to boot into my backup one more time so that I can back everything up, so even if it's only a temporary fix, I'm okay with that too. Any suggestions?
Click to expand...
Click to collapse
https://forum.xda-developers.com/oneplus-one/general/tool-oneplusrecovery-tool-v1-0-restore-t2991851
Sounds like a Hardware issue? Sorry to say what your saying doesn't add up and or make sense. Fastboot should work no matter what even if you soft brick it and mess up recovery. I suggest letting the power fully drain maybe and google how to fast boot in case you are doing it wrong.
Mr.Ak said:
https://forum.xda-developers.com/oneplus-one/general/tool-oneplusrecovery-tool-v1-0-restore-t2991851
Click to expand...
Click to collapse
I've tried that but it can't find the phone. The phone gets detected as a new device in windows as evident from the device connection sound but it also never shows up in the list of devices from My Computer.
AMpageg2 said:
I've tried that but it can't find the phone. The phone gets detected as a new device in windows as evident from the device connection sound but it also never shows up in the list of devices from My Computer.
Click to expand...
Click to collapse
I agree with what @Shinobi_warrior said.Seems like you just have a soft brick,so you should be able to boot into fastboot mode without any issues.Are you sure you're doing it the right way? Did you try draining battery completely and then booting into fastboot(yes,you don't need much battery to boot into fastboot mode)?
Well I was finally able to get the device detected by ADB, but it just shows as offline. I attempted to use the repair kit and nothing seemed to happen. I also attempted a different tool (https://forum.xda-developers.com/on.../oneplus-one-toolkit-manudroid19-gui-t2807418) and then booting into either fastboot or recovery that way, a terminal window pops up and quickly disappears, and then nothing else happens. I still see the TugaPower boot logo and it still goes to the blank black screen after this.
My father-in-law's S6 was rebooting right after the menu screen came up. After trying numerous things which wouldn't work (still had varying boot loops) like getting into the recovery mode and doing a factory wipe, I decided to use Odin and flash the base stock Android nougat on this (it had the one verizon security patch after that, so should be no issue doing this).
That went okay and it rebooted and got all the way to "Android is starting" which you see after a firmware upgrade. But I didn't realize the battery had run down through all this so it died at this stage. So it was taking a charge now, so let it charge overnight and give it another run.
Got up today, tried to start it...back to the boot loop. So I figured I'd flash stock again with Odin (can always get back to that mode).
It completes successfully and then after the reboot at about 32% jumps to "erasing" and then the boot loop again.
Got into recovery mode once and wiped cache (pointless at this point, but whatever) and did factory reset there, then boot to bootloader. Got all the way to the verizon screen...and then boot loop again.
Is this phone just done? The only thing I can consistently get to is Odin mode. I tried the stock reflash a couple more times and keep ending up in a boot loop and it doesn't even get past the "custom" screen now. And I can't even actually get it to shutdown for that matter. I can get to the battery pull mode but if I try to power off from there, I just get the black screen with the blue light.
And, to make matters even worse, now on restart, it brings up the blue system update screen for a second, then jumps over to the no command screen, sits there for a second, then reboots again. I think I've somehow managed to even blow the recovery menu but this has all been stock and never had any custom firmware or root.
Any help/suggestions would be greatly appreciated!