Related
Hello, unfortunately Exposed quit working. And troubleshooting caused me to find out both android version and Rom is out of date. Currently android 4.4.2 and viper 1.8.0. Viper 4.0+ isn't supported on Verizon, should I flash 4.0 or a pervious version? Should I flash each update or go straight to the latest? since my devices says "no updates available" Should I flash android 4.4.3/4 The same way as a Rom?
Also I'm on twrp 2.7.1.0 and updating to 2.8.5.0 failed, any suggestions?
I would make sure to be on the latest firmware before I do anything..then I would fastboot 2.8.5.0. Last I would install the latest version of the ROM you want to run that's supported.
the 4.4.4 fireware flashed sucessfully.
when engagaing twpr install from 2.7.1.0 -. 2.8.5.0 said failed, yet when booting into recoveru said twrp 2.8.5.0
flashed rom (viper 3.2x.x
now stuck at boot img screen.
attempts to boot into recovery have failed.
sugggestions?
AlPoo said:
the 4.4.4 fireware flashed sucessfully.
when engagaing twpr install from 2.7.1.0 -. 2.8.5.0 said failed, yet when booting into recoveru said twrp 2.8.5.0
flashed rom (viper 3.2x.x
now stuck at boot img screen.
attempts to boot into recovery have failed.
sugggestions?
Click to expand...
Click to collapse
You can hold power an vol up to force a reboot when reboot starts let go of power an vol up an hold vol down which will take u to bootloader.. Did You fastboot the recovery.IMG?
Tigerstown said:
You can hold power an vol up to force a reboot when reboot starts let go of power an vol up an hold vol down which will take u to bootloader.. Did You fastboot the recovery.IMG?
Click to expand...
Click to collapse
had trouble with this, twrp application said failed install. yet fastboot -> recovery worked. after flashing rom, i get SIM card from unknown source. so now i have a radio problem?
AlPoo said:
had trouble with this, twrp application said failed install. yet fastboot -> recovery worked. after flashing rom, i get SIM card from unknown source. so now i have a radio problem?
Click to expand...
Click to collapse
Don't know if its a radio issue. Maybe a ROM issue I don't run viper or follow so I could not tell you either way..power down phone remove sim turn phone on put sim in just something you could try. Or try a different ROM an see if you have this issue still.
Tigerstown said:
Don't know if its a radio issue. Maybe a ROM issue I don't run viper or follow so I could not tell you either way..power down phone remove sim turn phone on put sim in just something you could try. Or try a different ROM an see if you have this issue still.
Click to expand...
Click to collapse
for some reason i have a working data connection and can send recieve sms but when placing a call it drops. will try a new rom after this.
AlPoo said:
for some reason i have a working data connection and can send recieve sms but when placing a call it drops. will try a new rom after this.
Click to expand...
Click to collapse
Make sure your network is set to global
I just got a broken Nexus5 with a boot-loop issue. As soon as the Google logo appears it reboots. I can enter booloader normally but if I select recovery the same happens, reboot. I unlocked the bootloader and flashed TWRP in, same thing. Tried to flash full stock 5.1.1, same thing.
Any ideas?
Himeko7 said:
I just got a broken Nexus5 with a boot-loop issue. As soon as the Google logo appears it reboots. I can enter booloader normally but if I select recovery the same happens, reboot. I unlocked the bootloader and flashed TWRP in, same thing. Tried to flash full stock 5.1.1, same thing.
Any ideas?
Click to expand...
Click to collapse
Try flashing stock google image 5.1 with or without fastboot.
ghosty7 said:
Try flashing stock google image 5.1 with or without fastboot.
Click to expand...
Click to collapse
I did already as I mentioned. But I can't even enter TWRP, as soon I select recovery it reboots. Faulty board/storage?
Himeko7 said:
I did already as I mentioned. But I can't even enter TWRP, as soon I select recovery it reboots. Faulty board/storage?
Click to expand...
Click to collapse
You said 5.1.1 that is not out yet only 5.1. Also you do not need TWRP to flash google stock image, if you can get into bootloader as you said, you can flash the image with your PC. or am i missing something ?
http://forum.xda-developers.com/google-nexus-5/general/tutorial-how-to-flash-factory-image-t2513701
ghosty7 said:
You said 5.1.1 that is not out yet only 5.1. Also you do not need TWRP to flash google stock image, if you can get into bootloader as you said, you can flash the image with your PC. or am i missing something ?
http://forum.xda-developers.com/google-nexus-5/general/tutorial-how-to-flash-factory-image-t2513701
Click to expand...
Click to collapse
Sorry I meant 5.1.0 from https://developers.google.com/android/nexus/images
I first flashed TWRP with the idea to install CM from there, but then I can't even enter it (all commands through fastboot work just fine), which is a pretty bad sign I guess. Then I flashed stock 5.1.0, and nothing changed.
Himeko7 said:
Sorry I meant 5.1.0 from https://developers.google.com/android/nexus/images
I first flashed TWRP with the idea to install CM from there, but then I can't even enter it (all commands through fastboot work just fine), which is a pretty bad sign I guess. Then I flashed stock 5.1.0, and nothing changed.
Click to expand...
Click to collapse
That does not sound good at all...
Himeko7 said:
I just got a broken Nexus5 with a boot-loop issue. As soon as the Google logo appears it reboots. I can enter booloader normally but if I select recovery the same happens, reboot. I unlocked the bootloader and flashed TWRP in, same thing. Tried to flash full stock 5.1.1, same thing.
Any ideas?
Click to expand...
Click to collapse
Power button issue?
zagorteney said:
Power button issue?
Click to expand...
Click to collapse
I don't think so, phone stays in bootloader indefinitely until I reboot or try to enter recovery.
Today I accidently wiped my internal and external sd card from twrp recovery mode. I was on Lolipop 5.1.
As I wanted to install Cyanogenmod Rom I tried to reflash CWM recovery. Ater doing that I was not able to enter the twrp recovery anymore. I had accecs to the unlocked bootloader and tried to reinstall the boot, recovery and system via fastboot but without any success. The phone did not boot and I couldnt enter recovery mode anymrore.
Now I accidently flashed via fastboot a wrong boot and recovery firmware (4.1) and since that I can not even enter fastboot. The pictre shows where I am stuck. On the bootloader page it says:
Error
Func NO: 10 (FUNC_BOOT_RECOVERY)
Error NO: 2
Can somebody help me to repair my device? Its brandnew.
What can I do without a recovery, without a system and without fastboot.
Here is the picture:
hxxp://s21.postimg.org/tqzu1wlhj/IMG_0191.jpg
balpem said:
Today I accidently wiped my internal and external sd card from twrp recovery mode. I was on Lolipop 5.1.
As I wanted to install Cyanogenmod Rom I tried to reflash CWM recovery. Ater doing that I was not able to enter the twrp recovery anymore. I had accecs to the unlocked bootloader and tried to reinstall the boot, recovery and system via fastboot but without any success. The phone did not boot and I couldnt enter recovery mode anymrore.
Now I accidently flashed via fastboot a wrong boot and recovery firmware (4.1) and since that I can not even enter fastboot. The pictre shows where I am stuck. On the bootloader page it says:
Error
Func NO: 10 (FUNC_BOOT_RECOVERY)
Error NO: 2
Can somebody help me to repair my device? Its brandnew.
What can I do without a recovery, without a system and without fastboot.
Here is the picture:
hxxp://s21.postimg.org/tqzu1wlhj/IMG_0191.jpg
Click to expand...
Click to collapse
So (Vol-) + (Power) w/ usb plugged in doesn't bring it to recovery mode? Have you tried with HiSuite?
jfer671 said:
So (Vol-) + (Power) w/ usb plugged in doesn't bring it to recovery mode? Have you tried with HiSuite?
Click to expand...
Click to collapse
No because I had twrp recovery installed and tried to flash cwm over it. After that I had no recovery at all. But I made some progress now... I am able to flash the same newest twrp 2.8.7.0 recovery to the phone and I managed also to flash the 5.1 stock recovery. I flashed BOOT.img from 5.1 and SYSTEM.img from 5.1 and I got rid of the error in fastboot menu.
Stock recovery I can flash via installer_r24.4.1-windows from acbka.
http://forum.xda-developers.com/mate-7/orig-development/tool-android-4-4-5-1-pc-t3186984
And these two recoveries seems to be the only one that work on my phone....? Currently I have stock recovery installed and i put MT7-L09C900B324 on my sd card (dload/UPDATE.app) and did the three buttons rescue. It seemed to work but It stoped at 90% and still no luck. What am I doing wrong this time?
Hi Suite does not recognitze the phone. When I abort the istallation and reboot the phone starts with the Huawei Logo and goes black and starts to the Huawei logo and goes black and so on...
Here is a picture of where i am stuck at 90% right now, so close...:
hxxp://s13.postimg.org/p093toz5z/IMG_0192.jpg
SOLVED
After a 36 hour marathon my mate 7 is back and working. the trick was to flash the stock recovery for all Lollipop versions wich can be foudn here: http://forum.xda-developers.com/mat...8-7-0-mate7-android-5-1-t3156779/post61958212 via linux. I somehow seem to have had trouble over wndows.
And after that do the three button rescue with the newest B 324 firmware which I have had installed before I destroyed my OS..
and my camera is now running normaly which was the initial reason i tried to install a other firmare.
:laugh:
balpem said:
...the trick was to flash the stock recovery for all Lollipop versions
Click to expand...
Click to collapse
When you say flash stock recovery for all LP versions, did you flash and then reboot each time? or flash over and when complete, flash over again still on fastboot?
Can you briefly describe in steps? Tnx! and Glad you were able to recover
jfer671 said:
When you say flash stock recovery for all LP versions, did you flash and then reboot each time? or flash over and when complete, flash over again still on fastboot?
Can you briefly describe in steps? Tnx! and Glad you were able to recover
Click to expand...
Click to collapse
I flashed via fastboot the stock recovery which you can download via the link above. the provider (user rowihel2012) claims, that this recovery works for all lolipop stock roms.
After that I made a reboot and pressed (power button and volume+) to check if its installed.
Than I downloaded the lollipop version I have had previously installed. In my case this was the B324 European version.
I put it on my sd card (dload/UPDATE.app) and launched the phone with the three button rescue method. The recovery recognized the rom on the sdcard and started to flash the OS.
After less than 5 min, my phone was restored.
I have made the experience, when using certain roms (B324, B308 etc..) with certain stock recoveries, I was not able to flash the OS and the recovery stoped always at 90%.
The recovery linked above seems to work great for the B324 version, I haven't tried any other stock roms with it.
I wonder if this will work for B327? Seems the actual last update for LP was B324, now I can't seem to get out of this firmware to go back to KK. When I flash transition B300, it's successful...but for some odd reason, when I flash 137, 143, 145 or 148...I auto go back to B327. This, after the fact I'm flashing those firmware's recoveries. Any ideas what I might do to get out of 327?
---------- Post added at 01:42 PM ---------- Previous post was at 01:38 PM ----------
Also, what's this Vol+ and Power technique?, all I get is the three menu screen (reboot, factory reset and format cache).
jfer671 said:
I wonder if this will work for B327? Seems the actual last update for LP was B324, now I can't seem to get out of this firmware to go back to KK. When I flash transition B300, it's successful...but for some odd reason, when I flash 137, 143, 145 or 148...I auto go back to B327. This, after the fact I'm flashing those firmware's recoveries. Any ideas what I might do to get out of 327?
---------- Post added at 01:42 PM ---------- Previous post was at 01:38 PM ----------
Also, what's this Vol+ and Power technique?, all I get is the three menu screen (reboot, factory reset and format cache).
Click to expand...
Click to collapse
You can try this recovery above which should work for all lollipop roms but I have no better idea as I have had basicly the same problem and could only flash the former rom i had installed whch was B324.
The Vol+ and Power i do to get into the recovery menu (the three menu screen) to check if the recovery was flashed successfully. I have had often the problem after flashing a recovery that it did not work. this is to check if the recovery works.
When i tried to flash a cwm recovery, i couldnt enter any recovery mode after that anymore. I panicked at this point but than i realised that not all recoveries did work for me. For example I could never flash a CWM recovery, not sure why. Maybe because I tried to flash a 4.4 recovery and I had a 5.1 BOOT.img installed?
balpem said:
After a 36 hour marathon my mate 7 is back and working. the trick was to flash the stock recovery for all Lollipop versions wich can be foudn here: http://forum.xda-developers.com/mat...8-7-0-mate7-android-5-1-t3156779/post61958212 via linux. I somehow seem to have had trouble over wndows.
And after that do the three button rescue with the newest B 324 firmware which I have had installed before I destroyed my OS..
and my camera is now running normaly which was the initial reason i tried to install a other firmare.
:laugh:
Click to expand...
Click to collapse
balpem said:
You can try this recovery above which should work for all lollipop roms but I have no better idea as I have had basicly the same problem and could only flash the former rom i had installed whch was B324.
The Vol+ and Power i do to get into the recovery menu (the three menu screen) to check if the recovery was flashed successfully. I have had often the problem after flashing a recovery that it did not work. this is to check if the recovery works.
When i tried to flash a cwm recovery, i couldnt enter any recovery mode after that anymore. I panicked at this point but than i realised that not all recoveries did work for me. For example I could never flash a CWM recovery, not sure why. Maybe because I tried to flash a 4.4 recovery and I had a 5.1 BOOT.img installed?
Click to expand...
Click to collapse
I see, so then it seems like some recoveries did in fact work with fastboot on me, because the Vol+ and Power worked, but it either only put me in V100R001C900B300 OR MT7-L09C900B300. I've read that I can't just flash KK over LP, that I needed to flash the B300 which is why I flashed transition package first. Should I not have done this?
Once in transition mode though (I booted up and checked, then went back into recovery), if I flashed 4.4 (recovery), it oddly put me back to B327...strange even though the recovery flashed was B137 or B145.
Let me see this link above. I'm back again at 5.1.1 LP B327. I'll do instead fastboot and flash above the recovery and so on, and I'll post the results, if any. Oddly enough, if I flashed boot, recovery and system images of 4.4, I get an "Android" boot screen that hangs, no Huawei.
I really like LP because of some of the features not found in KK like the dual windows, camera tweaks, etc. But no root yet available. TWRP doesn't seem to work as well, fails in fastboot.
balpem said:
After a 36 hour marathon my mate 7 is back and working. the trick was to flash the stock recovery for all Lollipop versions wich can be foudn here: http://forum.xda-developers.com/mat...8-7-0-mate7-android-5-1-t3156779/post61958212 via linux. I somehow seem to have had trouble over wndows.
And after that do the three button rescue with the newest B 324 firmware which I have had installed before I destroyed my OS..
and my camera is now running normaly which was the initial reason i tried to install a other firmare.
:laugh:
Click to expand...
Click to collapse
Okay...so I was able to flash down to B324, but not via the link provided. What I did was, flash B300 cust.img on (fastboot) then flash boot/recovery/cust/system.img (fastboot). Rebooted with VolumeUp + Power to check for recovery (success), performed a wipe and done! Back to B324.
Now I gotta figure how to go back down to B145, which is where I was at with Root and with no problems at all. If I flash B300 again and then B145...I get the "Android" logo (instead of Huawei) and then the HAM7 reboots and recovers itself back to B324.
Hi, I'm new to XDA. Sorry if I did something wrong already. But I have a problem, I tried installing a new boot animation to my moto e 1st gen (bootloader was unlocked, it was rooted too). Now whenever I turn the phone on, The WARNING BOOTLOADER UNLOCKED image shows up, but there is no boot animation. I cannot access anything, I can only go into recovery mode and CWM. I have tried factory reset using Recovery Mode (No success, just does WARNING boot loop again ) I have also tried factory reseting through CWM, till no success. I am giving up, I just recently bought this phone. NAY help would be appreciated. Thanks in advance!
rakibshahid said:
Hi, I'm new to XDA. Sorry if I did something wrong already. But I have a problem, I tried installing a new boot animation to my moto e 1st gen (bootloader was unlocked, it was rooted too). Now whenever I turn the phone on, The WARNING BOOTLOADER UNLOCKED image shows up, but there is no boot animation. I cannot access anything, I can only go into recovery mode and CWM. I have tried factory reset using Recovery Mode (No success, just does WARNING boot loop again ) I have also tried factory reseting through CWM, till no success. I am giving up, I just recently bought this phone. NAY help would be appreciated. Thanks in advance!
Click to expand...
Click to collapse
Hello,
Can you tell us what firmware was your phone running? Also what recovery do you have on your phone?
If stock, you may try flashing stock firmware via fastboot.
-Vatsal
Vatsal said:
Hello,
Can you tell us what firmware was your phone running? Also what recovery do you have on your phone?
If stock, you may try flashing stock firmware via fastboot.
-Vatsal
Click to expand...
Click to collapse
Thanks for responding so quickly! But I fixed the problem a few minutes after posting this . But there is a new problem, I downgraded from Android 5.0.2 to Android 4.4.2. After doing this the phone worked perfectly. Then a few minutes later it installed a system update for 4.4.4 and now the phone is hard bricked. I can't access recovery mode, CWM, or even turn the phone on now. Before charging the phone, if I held the power button for a long time, the LED lit up and turned back off. Now there is no response from the phone at all no matter what I do.
Also, I had ClockWorkMod and stock recovery on my phone (Is stock recovery the one that shows up when you hold power+volume down? If so I had both CWM and stock) But now I can't access either recovery modes. If it at least went into stock recovery, I'd flash stock firmware, root it, install CWM, and flash a Lollipop zip. (I like Lollipop, I don't know why there are so many people that hate Lollipop )
Any help would be much appreciated. All i need now is a way to flash files without going into recovery mode on phone.
Hi, need some urgent help here.
I was trying to install a custom rom, so I unlocked first the bootloader, then flashed twrp 3.0.2 for Android 5.1 and with it I flashed KangVip rom (porto from honor 6).
Problem was it didn't boot, just black screen.
So I supposed the problem was with the rom so I flashed via fastboot the aosp 6, obviously with same results.
I tried lot of stuff (twrp 2.8.x.x, reinstall stock firmware, restore twrp backup of stock full firmware and so on - I did almost everything I could do) and now I'm with a Huge problem: no huawei logo at start, just a white screen and nothing happen. I have twrp 3.0.2 for 5.1 installed right now but I can't install stock recovery.
Please help me, what do I gotta do?
[emoji30]
the ported rom is based on Android 6.0 you have Android 5.1 youk should flash 5.1 based rom..
it's good to flash stock and update official to b560 or b571 depending on which region to have then flash twrp recovery and then flash desire rom..
fazi2015 said:
the ported rom is based on Android 6.0 you have Android 5.1 youk should flash 5.1 based rom..
it's good to flash stock and update official to b560 or b571 depending on which region to have then flash twrp recovery and then flash desire rom..
Click to expand...
Click to collapse
Thx for this.
But I have a problem, I can't install stock recovery and if I try to flash the .img files extracted from update.app nothing happens.
Also, I still have that problem with huawei logo disappeared and a blank white screen instead.
Sent from my HUAWEI GRA-L09 using Tapatalk
boot into bootloader and flash stock recovery but if you know what exactly firmware was you have(bxxx) then no need to flash recovery just put update.app to your sd card and then force update three buttons combination (volume both and power) turn off it remove data cable then press these three buttons it'll go in recovery sometime but try two or three times(in recovery turn off device) and try again if that method not work you should flash stock recovery to do so and if it didn't go to bootloader(fastboot) then connect data cable and then press vol- and power it'll go to bootloader in bootloader flash stock recovery then force update your device....
fazi2015 said:
boot into bootloader and flash stock recovery but if you know what exactly firmware was you have(bxxx) then no need to flash recovery just put update.app to your sd card and then force update three buttons combination (volume both and power) turn off it remove data cable then press these three buttons it'll go in recovery sometime but try two or three times(in recovery turn off device) and try again if that method not work you should flash stock recovery to do so and if it didn't go to bootloader(fastboot) then connect data cable and then press vol- and power it'll go to bootloader in bootloader flash stock recovery then force update your device....
Click to expand...
Click to collapse
Solved, thanks!
Sent from my HUAWEI GRA-L09 using Tapatalk
fazi2015 said:
boot into bootloader and flash stock recovery but if you know what exactly firmware was you have(bxxx) then no need to flash recovery just put update.app to your sd card and then force update three buttons combination (volume both and power) turn off it remove data cable then press these three buttons it'll go in recovery sometime but try two or three times(in recovery turn off device) and try again if that method not work you should flash stock recovery to do so and if it didn't go to bootloader(fastboot) then connect data cable and then press vol- and power it'll go to bootloader in bootloader flash stock recovery then force update your device....
Click to expand...
Click to collapse
Hope you can help me out here...I had just gotten my HAM7 for a couple of days. Was on 4.4.2 B120, was able to get it up to B326. Just yesterday I attempted to flash up to B331 and it succeeded according to the "local update" option. Then it went on boot loop. I tried doing the force 3-button option and that worked to the point of saying it succeeded and will reboot. Now I'm stuck on Ascend Mate logo. I can no longer get into factory option mode (V+Power), only fastboot mode. Also, I can't do force update no more so I can't try any other "update.app" unless I'm missing something here.
Any help in getting this unit at least back to working condition will be a BIG help. I just received this two days ago.
Thx!!!!
jfer671 said:
Hope you can help me out here...I had just gotten my HAM7 for a couple of days. Was on 4.4.2 B120, was able to get it up to B326. Just yesterday I attempted to flash up to B331 and it succeeded according to the "local update" option. Then it went on boot loop. I tried doing the force 3-button option and that worked to the point of saying it succeeded and will reboot. Now I'm stuck on Ascend Mate logo. I can no longer get into factory option mode (V+Power), only fastboot mode. Also, I can't do force update no more so I can't try any other "update.app" unless I'm missing something here.
Any help in getting this unit at least back to working condition will be a BIG help. I just received this two days ago.
Thx!!!!
Click to expand...
Click to collapse
are you have unlock bootloader or not..
fazi2015 said:
are you have unlock bootloader or not..
Click to expand...
Click to collapse
Yes, bootloader is unlocked. FYI, I can't do Vol+ Power or 3-button force. I have no idea what went wrong after the B331 update.app flash. It said successful then boot loop after. I have looked all over the forums and tried everything from flashing C900B300 rollback to try and get 4.4.2 that I started out with, but I really don't know which firmware to start with. The last update.app files I was using was the European variants. Phone was originally locked to Ecuador MoviStar network at B120SP04, then I flashed up to B324 5.1.1. Rooted and then wanted to upgrade to B331 so I unrooted and flashed. Now I'm stuck.
jfer671 said:
Yes, bootloader is unlocked. FYI, I can't do Vol+ Power or 3-button force. I have no idea what went wrong after the B331 update.app flash. It said successful then boot loop after. I have looked all over the forums and tried everything from flashing C900B300 rollback to try and get 4.4.2 that I started out with, but I really don't know which firmware to start with. The last update.app files I was using was the European variants. Phone was originally locked to Ecuador MoviStar network at B120SP04, then I flashed up to B324 5.1.1. Rooted and then wanted to upgrade to B331 so I unrooted and flashed. Now I'm stuck.
Click to expand...
Click to collapse
now you should flash twrp recovery in fastboot mode and then flash a custom rom like kangvip I'll send you link soon...
fazi2015 said:
now you should flash twrp recovery in fastboot mode and then flash a custom rom like kangvip I'll send you link soon...
Click to expand...
Click to collapse
Thank you very much....hope that will solve the boot issue and bring this unit back to life
Alright, so I've given up complete hope that I can get my unit back up and running again. I've tried so many ways already with no success (fastboot/adb, force upgrade, etc.,), and even tried to copy my second HAM7 images (via sdk tools) and to no avail.
The thing I'm trying to understand is where exactly do I start with trying to revive? When I first got this device from eBay, it was apparently still on "MoviStar" Telefonica-Spain network so my network bars showed "R" for roaming. Somehow, I was able to flash it from being on V100R001C00B120SP04a and upgrade to B127>B145>B324 which made me able to use my own service normally. It worked fine and I was even able to root it. Decided to do a last upgrade to B331 and while the local update option showed it as successfully installed, it went into boot loop ever since. Hence, I used European firmwares for most of the flashing. My second mate was on B145 and I was able to get that to B331, which is running fine right now.
ATM, I am ONLY able to do Volume-/Power to get into fastboot.
Doesn't work:
- V+/Power (stock recovery)
- V-+/Power (3-button force)
What works:
- V-/Power with USB for fastboot
*Bootloader is unlocked, but I do believe that after flashing the last firmware of B331, I may have done a factory wipe, which probably reset the USB debugging option as well. So, I'm sure I'm stuck with a device that just might be flashed on the wrong firmware and is factory reset which prevents me from flashing a custom rom or even the stock rom???
Any last advice I would be so thankful for...still waiting on the link for KangVip rom from (fazi2015)
All the best...
jfer671 said:
Alright, so I've given up complete hope that I can get my unit back up and running again. I've tried so many ways already with no success (fastboot/adb, force upgrade, etc.,), and even tried to copy my second HAM7 images (via sdk tools) and to no avail.
The thing I'm trying to understand is where exactly do I start with trying to revive? When I first got this device from eBay, it was apparently still on "MoviStar" Telefonica-Spain network so my network bars showed "R" for roaming. Somehow, I was able to flash it from being on V100R001C00B120SP04a and upgrade to B127>B145>B324 which made me able to use my own service normally. It worked fine and I was even able to root it. Decided to do a last upgrade to B331 and while the local update option showed it as successfully installed, it went into boot loop ever since. Hence, I used European firmwares for most of the flashing. My second mate was on B145 and I was able to get that to B331, which is running fine right now.
ATM, I am ONLY able to do Volume-/Power to get into fastboot.
Doesn't work:
- V+/Power (stock recovery)
- V-+/Power (3-button force)
What works:
- V-/Power with USB for fastboot
*Bootloader is unlocked, but I do believe that after flashing the last firmware of B331, I may have done a factory wipe, which probably reset the USB debugging option as well. So, I'm sure I'm stuck with a device that just might be flashed on the wrong firmware and is factory reset which prevents me from flashing a custom rom or even the stock rom???
Any last advice I would be so thankful for...still waiting on the link for KangVip rom from (fazi2015)
All the best...
Click to expand...
Click to collapse
https://mega.co.nz/#!3N4RzbJY!saB4NY...Ao5goVNiSXAjEc
I am not 100% sure about this rom but you can try it in fastboot you should flash twrp recovery first..
fazi2015 said:
https://mega.co.nz/#!3N4RzbJY!saB4NY...Ao5goVNiSXAjEc
I am not 100% sure about this rom but you can try it in fastboot you should flash twrp recovery first..
Click to expand...
Click to collapse
Unfortunately, it says the file is no longer available
jfer671 said:
Unfortunately, it says the file is no longer available
Click to expand...
Click to collapse
try this all information is here
https://forum.xda-developers.com/mate-7/orig-development/rom-kangvip-rom-mate7-emui3-1-b351-t3228597
fazi2015 said:
try this all information is here
https://forum.xda-developers.com/mate-7/orig-development/rom-kangvip-rom-mate7-emui3-1-b351-t3228597
Click to expand...
Click to collapse
Okay, so final result is I'm stuck on a frozen logo now. The twrp bat file again showed success in flashing and rebooted the device, but I'm hung on the "Huawei Ascend" logo. I have to pull the battery to shut it off, otherwise it stays on. So I'm now sure that it's a hard bricked device since I did the stupid thing of factory resetting which probably reset the usb debug...making it almost impossible to flash any firmware now.
Thanks for the help anyways...I really appreciate it. Gonna throw this up on eBay and see if anyone wants it for parts
jfer671 said:
Okay, so final result is I'm stuck on a frozen logo now. The twrp bat file again showed success in flashing and rebooted the device, but I'm hung on the "Huawei Ascend" logo. I have to pull the battery to shut it off, otherwise it stays on. So I'm now sure that it's a hard bricked device since I did the stupid thing of factory resetting which probably reset the usb debug...making it almost impossible to flash any firmware now.
Thanks for the help anyways...I really appreciate it. Gonna throw this up on eBay and see if anyone wants it for parts
Click to expand...
Click to collapse
I know it's annoying but last time I research more and guide you I was have same problem don't give up....
I send you recovery flash in fastboot no need of usb debugging usb debugging need for adb not for fastboot in fastboot flash recovery by your self download it
https://mega.co.nz/#!GRw0CZjQ!iZllDkA6yJeWk7iEA4vEVA94r2nM_YjAuiS8B9IZdm0
then extract the zip go to resource and hold shift and left click then select open command port here then power off device completely boot into fastboot (bootloader) connect the device to pc and in command port type
fastboot flash recovery twrp_2_7.img
after that type
fastboot reboot and hold the volume- button of device it'll boot into recovery if you success then reply..
I've noticed two things when flashing KK or LP. On KK, the phone does a constant boot loop with Huawei logo (on off on off), but on LP the Huawei logo hangs...it doesn't boot loop. Is this an indication or just a fault with both OS?