[Completed] Galaxy Note 3 LTE Stuck in bootloop - XDA Assist

I very recently purchased a used Galaxy Note 3 that has been well used and loved. I bought it because I was told that the phone died whilst updating to Lollipop and because of this, the phone will now not boot. It is stuck in a bootloop with Recovery........ In the top corner.
Now my problem is this, I cannot get into Recovery Mode. It Just turns off again before I can access the screen, vibrates, then comes back on, rinse and repeat. I can get I to Odin mode, download mode, if you like.
I have tried flashing a Lollipop stock OS onto the device but I continually had the same problem, so I downloaded a CWM Recovery and flashed that onto the phone, but now I'm getting an error of SEAndroid is not enforcing... Blah blah.
I am incredibly stuck here and I know literally nothing about rooting. I just want this fixed, and am willing to try anything you throw at me if you're willing to push me to get there. Thanks, and I appreciate any advice!

Thank you for using XDA Assist. If you bought a device that was not working it may not be recoverable. Your best bet is to flash the stock firmware using Odin in your case. I've provided a link below for your device. Look in the general and q&a forums for how to return your device to stock. Good luck to you!
http://forum.xda-developers.com/galaxy-note-3
Sent from my Nexus 9 using XDA Free mobile app

Thread closed.

Related

[Q] My Verizon S3 is bootlooping

I have searched threads all over XDA similar to this one to ensure it is not a duplicate. Sadly I have not found any so I hope one of you at XDA can help me. I got my Galaxy S3 and rooted it as soon as it was available. Then two days ago I flashed Cynogenmod 10 onto it without a hitch. I liked it a lot but sadly there were some shortcomings so I wanted to reflash stock. This is where I believe I messed up. I looked up some instructions, and gave it a go. When I turned on the phone, the annoying verizon bootup image and sound came on, but my phone goes no further. I have no care about my data, I just want my phone back to stock, could a developer assist me in this?
If so I would be eternally grateful.
Just reboot to recovery (hold home, volume up, and power). Wipe everything and flash again.
Sent from my SCH-I535 using xda app-developers app
trent407 said:
I have searched threads all over XDA similar to this one to ensure it is not a duplicate. Sadly I have not found any so I hope one of you at XDA can help me. I got my Galaxy S3 and rooted it as soon as it was available. Then two days ago I flashed Cynogenmod 10 onto it without a hitch. I liked it a lot but sadly there were some shortcomings so I wanted to reflash stock. This is where I believe I messed up. I looked up some instructions, and gave it a go. When I turned on the phone, the annoying verizon bootup image and sound came on, but my phone goes no further. I have no care about my data, I just want my phone back to stock, could a developer assist me in this?
If so I would be eternally grateful.
Click to expand...
Click to collapse
Click gs3 link in sig
thanks so much guys!! both of you were big helps
droidstyle said:
Click gs3 link in sig
Click to expand...
Click to collapse
Im having a similar issue as the OP. I made a mistake last night and flashed cwm via rom manager and then loaded CM10. Now my phone just bootloops, but I can get into cwm. MY nandroid backup wont load, says "file invalid". I try to get into odin mode but when I hold the volume buttons and the power it just boots into cwm.
Help!
dreamsti said:
Im having a similar issue as the OP. I made a mistake last night and flashed cwm via rom manager and then loaded CM10. Now my phone just bootloops, but I can get into cwm. MY nandroid backup wont load, says "file invalid". I try to get into odin mode but when I hold the volume buttons and the power it just boots into cwm.
Help!
Click to expand...
Click to collapse
hold volume down and the power button
sent from locked bootloadrer SGS3 running a custom kernel

[Q] Bad CWM flash, can't boot to anything

I've been running Slim Bean 2.7 with the latest Gapps package (released 10/04). I was having trouble switching between 3g and 4g so i thought I would reinstall SB and Gapps. To do this, I started by flashing CWM Touch but i apparently had a bad download. When i tried to boot into recovery after flashing CWM, I found that my phone flashed the Samsung screen with the blue text in the top left corner but then flashed off and stopped responding. I tried removing the battery but it continues to do the same thing. Any suggestions? Thanks for your help.
Can you get to download mode? If so, odin flash back to stock, take the ota, root and unlock and try again. I've been using the new TWRP and its fantastic so far.
This
Sent from my SCH-I535 using Tapatalk 2
Fortunately since you get a boot splash you should be able to recover with Odin, as suggested. Always always check md5 on ROM and recovery downloads.
I appreciate the quick repsonses everyone. It seems that I was able to interrupt the bootloop (I'm not sure if I'm using that correctly) by booting into download mode, restarting, and booting normally. I'm poorly versed in development, but I'm still trying to learn more about the ins and outs of my phone so I run into trouble from time to time. These forums are life-savers. Thanks again.
Please read forum rules before posting
Questions go in Q&A
Thread moved
Thanks
FNM

[Q] I am stupid and forgot to unlock bootloader before flashing a CM10 nightly. Help?

As the title says, I am really stupid and flashed a ROM before unlocking my bootloader. I had just rooted and that step completely crossed my mind.
When I try to boot, I get a screen that says: "System software not authorized by Verizon Wireless has been found on your phone. Please turn off your phone and go to the nearest Verizon Wireless store for help."
I have flashed CM10 before, but I recently cracked the screen on my phone and had it replaced with a new one. I have tried booting into recovery mode, which I is Volume up, home, and power I believe, I see a screen that says Samsung and has small blue text on the top left of the screen that says: "Recovery Booting..." but then it goes back to the error screen. I am unsure what to do at this point besides go to a Verizon store which I do not want to do. Thank you for your time helping.
section 6 of my guide will bring your device back.
droidstyles guide is awsome and will fix ya right up.
Sent from my SCH-I535 using xda app-developers app
Same Thing
I did the same thing awhile back. It was my first rom ever flashing i had to go into download mode and then re-flash it with odin. Then it booted right up and i was able to unlock boot and reflash and it worked perfectly.

[Q] Verizon Samsung Galaxy SIII (SCH-1535) BOOT LOOPED, LOST RECOVERY AND OS!!

HELP!!!
About 1 month ago, my Galaxy S3 running 4.4.2 (Completely stock: no root, rom, or custom firmware), suddenly got into a boot loop about 3 weeks after receiving the 4.4.2 update. At first, it would boot up completely into the OS, then shut down before I even had time to enter PIN. Sometimes, after shutting down, it would restart by itself, but only on some occasions. I was able to enter and constantly use recovery and download mode with no shutdowns, so it wasn't a battery problem, instead a software/firmware one. I found that if the phone was plugged in while booting, I was able to use the phone with no problem, but it shut off as soon as the charger was removed. I then factory reset it, wiped the cache and such, but the problem still persisted. After about not touching it for a week, the phone wouldn't even make it past the first Samsung boot animation and jingle without turning off. However, the plugging in method would make it go further into the boot sequence, but it still wouldn't boot into the OS. After leaving it alone for one more week, I then LOST RECOVERY ACCESS! It would boot up to the android figure, but shut off immediately. I was able to access download mode, and therefore, tried to flash an earlier firmware with ODIN.
The phone was recognized by ODIN, but the flashing process failed. I first tried to root the stock ROM, but ODIN couldn't find the recovery. I then tried to downgrade my firmware to 4.1.2. I got a FAIL message on my PC and an error message on the phone (in ODIN mode) saying, " SW REV CHECK FAIL: FUSED 2 BINARY 0" Now every time I try to turn on the phone, it goes straight into ODIN mode, and it shows the message, : Firmware upgrade encountered an issue, Please use Software Repair Assistant & try again" with an image of a phone and PC linked together, but being interrupted by a yellow triangle with an exclamation mark in it.
HELP ME PLEASE. I LOVE THIS PHONE AND I STILL HAVE A WHILE UNTIL I CAN GET A NEW ONE!!!!
Is your phone still under warranty with your wireless carrier? If it is, you may want to contact the customer support department. You may be able to get a new phone as a warranty replacement.
Cindy
Sent from my Samsung Galaxy Tab 4 8" model using Tapatalk
cindylike24 said:
Is your phone still under warranty with your wireless carrier? If it is, you may want to contact the customer support department. You may be able to get a new phone as a warranty replacement.
Cindy
Sent from my Samsung Galaxy Tab 4 8" model using Tapatalk
Click to expand...
Click to collapse
Good point cindy if its an internal hardware issue verizon will replace it at no charge
From my Wicked S3 running MIUI
how is this even possible?
gorilla29 said:
HELP!!!
About 1 month ago, my Galaxy S3 running 4.4.2 (Completely stock: no root, rom, or custom firmware), suddenly got into a boot loop about 3 weeks after receiving the 4.4.2 update. At first, it would boot up completely into the OS, then shut down before I even had time to enter PIN. Sometimes, after shutting down, it would restart by itself, but only on some occasions. I was able to enter and constantly use recovery and download mode with no shutdowns, so it wasn't a battery problem, instead a software/firmware one. I found that if the phone was plugged in while booting, I was able to use the phone with no problem, but it shut off as soon as the charger was removed. I then factory reset it, wiped the cache and such, but the problem still persisted. After about not touching it for a week, the phone wouldn't even make it past the first Samsung boot animation and jingle without turning off. However, the plugging in method would make it go further into the boot sequence, but it still wouldn't boot into the OS. After leaving it alone for one more week, I then LOST RECOVERY ACCESS! It would boot up to the android figure, but shut off immediately. I was able to access download mode, and therefore, tried to flash an earlier firmware with ODIN.
The phone was recognized by ODIN, but the flashing process failed. I first tried to root the stock ROM, but ODIN couldn't find the recovery. I then tried to downgrade my firmware to 4.1.2. I got a FAIL message on my PC and an error message on the phone (in ODIN mode) saying, " SW REV CHECK FAIL: FUSED 2 BINARY 0" Now every time I try to turn on the phone, it goes straight into ODIN mode, and it shows the message, : Firmware upgrade encountered an issue, Please use Software Repair Assistant & try again" with an image of a phone and PC linked together, but being interrupted by a yellow triangle with an exclamation mark in it.
HELP ME PLEASE. I LOVE THIS PHONE AND I STILL HAVE A WHILE UNTIL I CAN GET A NEW ONE!!!!
Click to expand...
Click to collapse
I would love to help, but please help me first. how do you claim to have 4.4 kitkat when for the i535 there is confirmed to only be 4.3 for a stock OS? this will make a big difference in the outcome of who can help you. Google and android both confirm that 4.3 is the last update for this phone coming from verizon. How can you have 4.4 stock with touchwiz and everything? unless you have AOSP, which is another things entirely. this phone does poorly for 4.4 in AOSP because we don't have a proper kernel or baseband for it. it wasn't officially released.
anyway, that is my question to you.
cyberkeeper1 said:
I would love to help, but please help me first. how do you claim to have 4.4 kitkat when for the i535 there is confirmed to only be 4.3 for a stock OS? this will make a big difference in the outcome of who can help you. Google and android both confirm that 4.3 is the last update for this phone coming from verizon. How can you have 4.4 stock with touchwiz and everything? unless you have AOSP, which is another things entirely. this phone does poorly for 4.4 in AOSP because we don't have a proper kernel or baseband for it. it wasn't officially released.
anyway, that is my question to you.
Click to expand...
Click to collapse
4.4.2 is the latest and probably the last update for the i535. This should fix your problem OP. http://forum.xda-developers.com/showthread.php?t=2791801
I wish it was.
cindylike24 said:
Is your phone still under warranty with your wireless carrier? If it is, you may want to contact the customer support department. You may be able to get a new phone as a warranty replacement.
Cindy
Sent from my Samsung Galaxy Tab 4 8" model using Tapatalk
Click to expand...
Click to collapse
No, Cindy, it isn't under warranty anymore. It has been more than one year. I wish it was though!
Thanks, but...
JudgeFutta said:
4.4.2 is the latest and probably the last update for the i535. This should fix your problem OP. http://forum.xda-developers.com/showthread.php?t=2791801
Click to expand...
Click to collapse
Thank you so much for your help. I flashed the file, and I got recovery back. However, the phone has just returned to the state that this problem begun with. It still goes further into the boot sequence (still won't start) when plugged in, but it will shut off before it finishes and as soon as it's unplugged. It won't even start the sequence without the charger.
Any other suggestions?
Is that so? I had no idea. I was told by Verizon the 4.3 is the last one. I certainly will investigate. On ODIN, make SURE you check the bootloader update option, F. Reset Time, and auto reboot. Otherwise, the bootloader will not allow you to boot.
Sent from my SCH-I535 using XDA Free mobile app
gorilla29 said:
Thank you so much for your help. I flashed the file, and I got recovery back. However, the phone has just returned to the state that this problem begun with. It still goes further into the boot sequence (still won't start) when plugged in, but it will shut off before it finishes and as soon as it's unplugged. It won't even start the sequence without the charger.
Any other suggestions?
Click to expand...
Click to collapse
Try flashing the .tar file from the second post. Also make sure you have odin setup correctly like cyberkeeper1 said.
cyberkeeper1 said:
Is that so? I had no idea. I was told by Verizon the 4.3 is the last one. I certainly will investigate.
Sent from my SCH-I535 using XDA Free mobile app
Click to expand...
Click to collapse
VRUDNE1 4.4.2 has been available for roughly two months.
Verizon PDF (laziness, Verizon did not change the software name to VRUDNE1): http://www.verizonwireless.com/support/system_update/galaxys3.html
Samsung PDF (click first question under FAQ): http://www.samsung.com/us/support/owners/product/SCH-I535MBBVZW?
Quick online search: http://www.droid-life.com/2014/06/19/verizons-samsung-galaxy-s3-galaxy-s4-mini-kit-kat/
SlimSnoopOS said:
VRUDNE1 4.4.2 has been available for roughly two months.
Verizon PDF (laziness, Verizon did not change the software name to VRUDNE1): http://www.verizonwireless.com/support/system_update/galaxys3.html
Samsung PDF (click first question under FAQ): http://www.samsung.com/us/support/owners/product/SCH-I535MBBVZW?
Quick online search: http://www.droid-life.com/2014/06/19/verizons-samsung-galaxy-s3-galaxy-s4-mini-kit-kat/
Click to expand...
Click to collapse
Many thanks, Slim.
Should be made a sticky. This is important stuff for this phone.
Sent from my SCH-I535 using XDA Free mobile app
cyberkeeper1 said:
Is that so? I had no idea. I was told by Verizon the 4.3 is the last one. I certainly will investigate. On ODIN, make SURE you check the bootloader update option, F. Reset Time, and auto reboot. Otherwise, the bootloader will not allow you to boot.
Sent from my SCH-I535 using XDA Free mobile app
Click to expand...
Click to collapse
Would the file go under PDA (AP) or BL?
gorilla29 said:
Would the file go under PDA (AP) or BL?
Click to expand...
Click to collapse
PDA (AP)
JudgeFutta said:
PDA (AP)
Click to expand...
Click to collapse
I tried everything you suggested. I am able to boot into the OS, but only while connected to power. Definitely helped, but didn't solve.
Any suggestions?
gorilla29 said:
I tried everything you suggested. I am able to boot into the OS, but only while connected to power. Definitely helped, but didn't solve.
Any suggestions?
Click to expand...
Click to collapse
However, the phone will still shut down once booted, despite it being connected to power.
gorilla29 said:
However, the phone will still shut down once booted, despite it being connected to power.
Click to expand...
Click to collapse
It may be the battery or the phone just went out.
JudgeFutta said:
It may be the battery or the phone just went out.
Click to expand...
Click to collapse
Maybe, but the phone never shuts off during recovery. I bet the phone is just done. Lol

[Completed] I would like to know what has gone wrong with my rooted Samsung Galaxy j7

Before you read my problem plz note that i am only 16 and i have very little knowledge about anything related to rooting.
I rooted my phone a month ago because i wanted to use Xmod for Clash of Clans. I tried using Kingroot but it didnt work so i installed TWRP using Odin through my pc. After that i flashed SuperSU and the phone got rooted.
I didnt want xmod anymore so i decided to unroot my phone. I wanted to install the stock recovery and i read that i can do this by flashing the recovery.img file using Flashfy. So when i flashed it the app said that i need to reboot my device. So i pressed reboot and the screen went blank. But it didnt reboot. The screen that says Samsung Galaxy J7, which comes whenever i reboot or restart my phone, shows up but doesnt change. It also says "recovery is not seandroid enforcing" on top of the screen. It started coming when i installed TWRP. Nothing happened when i long pressed the power button. So i took out the battery, put it back and did 3 things:
1) Switching it on using the power button,
2) Directly going to recovery, and
3) Putting it for charging without switching it on.
The same screen comes everytime. PLEASE tell me what has gone wrong as soon as possible and if there is a way to fix this. Thanks a lot in advance.
XDA Visitor said:
Before you read my problem plz note that i am only 16 and i have very little knowledge about anything related to rooting.
I rooted my phone a month ago because i wanted to use Xmod for Clash of Clans. I tried using Kingroot but it didnt work so i installed TWRP using Odin through my pc. After that i flashed SuperSU and the phone got rooted.
I didnt want xmod anymore so i decided to unroot my phone. I wanted to install the stock recovery and i read that i can do this by flashing the recovery.img file using Flashfy. So when i flashed it the app said that i need to reboot my device. So i pressed reboot and the screen went blank. But it didnt reboot. The screen that says Samsung Galaxy J7, which comes whenever i reboot or restart my phone, shows up but doesnt change. It also says "recovery is not seandroid enforcing" on top of the screen. It started coming when i installed TWRP. Nothing happened when i long pressed the power button. So i took out the battery, put it back and did 3 things:
1) Switching it on using the power button,
2) Directly going to recovery, and
3) Putting it for charging without switching it on.
The same screen comes everytime. PLEASE tell me what has gone wrong as soon as possible and if there is a way to fix this. Thanks a lot in advance.
Click to expand...
Click to collapse
Greetings,
Thank you for using XDA Assist.
There are no specific forums for your device on XDA.
However, if you create an XDA account, you can post your question here:
Android Q&A
You'll receive expert advice there.
Good luck and welcome to XDA!
Thanks for answering.
I have already asked the question on Q&A but there has been no reply. I will keep checking. Thanks again

Categories

Resources