I have a B90 TF101 and I am able to get into recovery mode. I have no ROM on my internal SD card and have wiped and formatted everything. I have read that it is possible to push a file using ADB while in recovery.
However I am not able to see my device when I use the adb devices command. I noticed that the drivers for the transformer are not installed. So I tried to install them and it tells me that windows can't install. I am pointing the installer to the MTP devices driver folder.
How do I get the drivers to work so I can use ADB or can I set up ADB in Linux and not have to worry about the drivers?
edit: I forgot to mention I am running windows vista.
Hi! Search in transformer's support page, you can find the drivers there
Are you saying that the drivers in the MTP folder are not the right ones? I got them right from Asus' website. Which drivers should I be using?
Ageesaman, did you ever get the drivers working? I had the exact same problem (got adb working as far as listing devices, but then it returned with a blank line after "adb devices" in cmd window). I downloaded the ASUS site's USB drivers download as well as every other utility from that site; I also tried external sources; finally, I tried manually updating by pointing to the unzipped MTP folder - nothing worked. I used both 64 and 32 bit Windows 7 machines. I am stuck in the cwm recovery loop so I can't do much troubleshooting. I tried searching dozens of sites for several hours but came up short.
Thanks in advance for any help offered.
Unfortunately I have not found a solution to getting the drivers installed. I was hoping someone would be able to confirm/deny if I can do this in Linux without the drivers before going through with setting it up. However that will be my next step as soon as I have the time to do it.
Ageesaman,
Unfortunately I know nothing about Linux, but what finally got it working for me was starting the installation of PDANet for Android. I saw it look for and install the driver, then I got a ADB confirmation. I then canceled the PDANet install. If you decide to go this route and get error messages in the cmd window, retry "adb devices" up to 3 times. In the meantime, I hope you get your Linux answer. Good luck.
I will give that a try. Is PDAnet something from Asus? I will do a search and see if I can find it.
ageesaman said:
Unfortunately I have not found a solution to getting the drivers installed. I was hoping someone would be able to confirm/deny if I can do this in Linux without the drivers before going through with setting it up. However that will be my next step as soon as I have the time to do it.
Click to expand...
Click to collapse
Yes, I can confirm the TF101 works with ADB without drivers on Ubuntu linux [I am on 11.04]. The current [stable, with 12.04 betas] Ubuntu version is 11.10, and you can download it to a live CD and run it off the CD without installing it.
I just got my tf101 the other day and I tried using adb [and older version], and it did not show up. Then I downloaded the tf101 root.zip file, and tried the adb within that folder, and it worked.
I've uploaded it to mediafire:
adb-1.0.29 http://www.mediafire.com/?hqwxbljs2gbpfxe
md5 64c4afbab6d2f769ddbb229f0247cf8a
update: newest adb is 1.0.31 http://www.mediafire.com/download.php?vcvc4dxkdd57695
md5 ed5c8f9a221cae0cb24d6cdc8b76d396
download, and run
chmod +x ./adb-1.0.29
to make it executable
That worked! I can now connect to my device with ADB. Thanks for that pdanet advice.
Now I just need to figure out how to push the file. Can't seem to get it to work. Here is what I am typing in the cmd line.
adb push rom.zip /sdcard
The rom I am trying to push is in the Platform tools folder that I am using to access adb. Does anybody know what I am doing wrong? Any help would be awesome.
is the rom.zip in the same directory as you are in (cd <path>)?
What does it say when you try to transfer it?
You can also try to push it to the full path (/mnt/sdcard/)
The first issue I had was that Asus sync was on and causing problems. As soon as I shut that off ADB started to work and act normal.
The file is in the same path.
When I try the transfer it looks like it finishes and it just tells me the file size. It actually seems like it works I just can't find the file when it is finished. I tried rebooting recovery but it seems like the file is just not there.
I will try the /mnt/sdcard/ and see if that works.
ageesaman said:
The first issue I had was that Asus sync was on and causing problems. As soon as I shut that off ADB started to work and act normal.
The file is in the same path.
When I try the transfer it looks like it finishes and it just tells me the file size. It actually seems like it works I just can't find the file when it is finished. I tried rebooting recovery but it seems like the file is just not there.
I will try the /mnt/sdcard/ and see if that works.
Click to expand...
Click to collapse
It's probably because /sdcard is a soft link to /mnt/sdcard/
if you did /sdcard/, I think it should probably work.
You sir are the man! Thanks for your time.
To get the process all in the same place for anyone else who may need this here you go. Just to make it clear.... This is what I did on my device and it worked. It may or may not work for you but maybe it's worth a try.
1. Downloaded SDK and Java JDK.
2. Used PDAnet to force windows to install the correct ADB device drivers.
3. When the drivers where installed and ADB was working I used this command to push the .zip file to the internal sd card.
adb push rom.zip /sdcard/
Just a few notes for this.
ADB was not working well at first because I had Asus sync running in the background. Make sure this is off.
Also make sure you put the file you are trying to push in the same directory you are using for ADB. For instance I used C:/android-sdk/platform-tools/ to access ADB so the file had to be in that folder in windows explorer.
To make it easier to type (I had to do this a lot while troubleshooting) I changed the name of the rom I was trying to push to rom.zip. This made typos less of an issue.
Make sure that you put the file extension (.zip in my case) in the ADB command even if it doesn't say it when you look at the file in windows explorer.
I think that is it in a nutshell. I hope this helps anyone else who needs to push a rom.
Good Luck
This method in this post didn't work for me, but this one did: http://forum.xda-developers.com/showthread.php?t=1689193
I set Windows to look for driver in c:. After a while one was installed and worked.
What I did on windows 7
Go to Device manager
Find transformer , right click on faulty marked unit.
Select properties
go to tab driver
update driver
Select browse
select path to the subfolder ANDROID ( containing usb drivers from asus )
include subfolders
Windows will find to alternatives , choose xxxx ADB
Windows will complain, ignore
done
/Claes R
W
This was answered a little bit in the S-Off thread and I would like to post it for everyone that has the PJ8310000 device and they are running into device "offline" when using adb devices. This is for Windows 8 only. I had the same problem in OSX, but I believe the solution is the same. I cannot post in the thread in the developer section yet, that is why this is here.
First, if you can't see your device in your device manager, make sure you have the latest HTC Device drivers installed or install the latest version of HTC Sync. This is very important for Windows 8.
Second, you will need to download and install the latest Android SDK. Just "Download From Other Platforms" and choose the appropriate SDK installation. You will need to run the SDK Manager.exe to install the latest tools. Note: ADB and Fastboot have been moved from the "tools" folder to "platform-tools".
Make sure your phone is in debugging mode by going into the Developer Options and choosing "Android debugging."
Find your SDK installation and make sure you are under "platform-tools" folder. You can ctrl-shift-right click on that folder to open a command prompt at that folder location. Saves you time.
Type in the command prompt:
Code:
adb devices
Your device should be listed and probably says Offline. This is normal. Take a look at your phone, you should get a prompt on your phone asking you if you trust the device that is trying to connect to it (this should be your computer). Allow it.
Type in the command prompt:
Code:
adb devices
This time, your device should be listed with the word "device" instead of offline.
To restart the daemon, type the following separately:
Code:
adb kill-server
adb start-server
This is the best I can do for everyone and it solved my problems with no further issues. I am not an expert and this is the only solution that has worked for me.
Thanks, this worked for me.
I did this in Windows 7 SP1 no problem. All I had to so was get the latest Android SDK and replace all the adb/fastboot files I already had and it worked no problems.
If you get permission denied when doing the last "adb shell" command, get adbd insecure from the forums here and run debugging mode insecurely from there.
Sent from my One X using xda app-developers app
Desertman123 said:
If you get permission denied when doing the last "adb shell" command, get adbd insecure from the forums here and run debugging mode insecurely from there.
Click to expand...
Click to collapse
I had this problem because SU was only allowing apps in CM10.1 (4.2.1). I found the solution by enabling the Dev Options via multiple clicks on the Build number until dev options was enabled, then changed Root access to Apps adn ADB.
FYI for anyone else that gets lost like I was.
ok so i can s-off now?
yes get some, 9 steps to s0ff
Ponarona said:
ok so i can s-off now?
Click to expand...
Click to collapse
Yes, you can use the HTC One XL link in the S-Off thread with no issues. I made this to help people with Win8 and trying to get their phones to appear properly in their device manager and to list it under adb devices.
If you get device offline, my issue, I was running android 4.2.2 but had an outdated adb. Just update adb if you still have problems
I know this is exceedingly random, but if you run a mac and can't see your device in adb, and in the past you tried sharing your phone internet with your mac via usb try running this:
sudo kextunload /System/Library/Extensions/EasyTetherUSBEthernet.kext
./adb kill-server
I need to do that before every adb session.
I'd be amazed someone actually has those conditions, but hey, it might help someone.
Sent from my HTC One X using xda app-developers app
Are you getting errors like "device not found" or "device offline" while trying to run ADB commands? Here's a quick way to troubleshoot your problem on Windows.
Steps
1. Ensure USB Debugging is enabled in Developer Options.
2. Verify current Google USB Driver is installed and that Device Manager is using that driver.
3. Update to latest version of ADB.
1. Ensure USB Debugging is enabled in Developer Options.
Enable Developer Options by going to Settings -> About Phone and tapping on "Build Number" multiple repeated times. You will be greeted with "You are a developer."
Now, under Settings -> Developer Options, ensure you check the box for "USB debugging."
2. Verify current Google USB Driver is installed and Device Manager is using that driver.
You may skip this step if Device Manager lists your phone as "Android Phone -> Android Composite ADB Interface." If it does not, this is likely your root cause.
Go to the Google USB Driver page and download the latest driver directly from Google. Extract the zip file to a folder you know and will remember in the future.
Open up Device Manger in Windows with your Nexus 5 connected. Whatever your Nexus 5 is currently detected as, right click on it and select Properties. Then, in the Driver tab, hit "Uninstall." If available, select "Delete the driver software for this device." and hit "OK." It will remove the old drivers.
Restart your computer.
After restarting, reconnect your Nexus 5. It should be recognized as an unknown device in the Device Manager. (If it isn't, try the previous driver deletion steps again.)
Right click on the unknown Nexus 5 device, choose Properties, and in the Driver tab again select "Update driver." Browse your computer manually by putting in the path to the new Google USB Drivers you unzipped to a folder of your choice in the beginning of this step. Choose next and your drivers should install! You'll know everything completed successfully when you see the phone listed under "Android Phone -> Android Composite ADB Interface" in Device Manager.
This is the most finicky process, so don't be afraid to reboot your computer a time or two and repeat these steps if they don't work on the first try.
3. Update to latest version of ADB.
This is a crucial step. The new version of ADB is required to work with the "USB debugging authorizations" setting.
Perhaps you know how to update ADB, in which case, just do it. However, here's a detailed manual approach to download JUST the adb suite from the SDK:
Go to the Google Android SDK website and choose "Use An Existing IDE" and click the "Download the SDK Tools for Windows." This will allow you to download only an 80 MB file rather than the whole 400 MB suite.
Install the SDK tools exe to a folder of your choosing.
Run SDK Manager and uncheck everything except for "Android SDK Platform-tools." This is the ADB and Fastboot bundle. Install that.
Navigate to your SDK Path as indicated at the top of your Android SDK Manager window. You will now see a freshly downloaded platform-tools folder containing ADB.exe, Fastboot.exe, and a host of other files. That folder is now your updated, portable ADB tools folder. You can move it anywhere you like as long as you run ADB from a command prompt window set to that directory.
After you've followed these procedures, running "ADB Devices" should trigger a prompt on your device to accept the RSA fingerprint of your computer. Accept it, and now all should be working as intended!
Questions? Ask below!
Crowd-sourced solutions.
Windows 8 Diagnosis
Yorus said:
The following worked for me, since all of the suggestions mentioned here didn't work for me:
If you use a Windows 8.1 enterprise N or KN edition, install the Microsoft Media Feature Pack :
http://support.microsoft.com/kb/2929699/en
Sounds too simple to be true but work instantly for me.
Hope it works you some of the people here looking for a solution
Click to expand...
Click to collapse
Setting up ADB and Fastboot commands to work from ANY path (credit to original author in quote).
Chromium_ said:
Setup, Preparation and Prerequisites
ADB and Fastboot Installation
Download the full Android SDK here (scroll to the bottom of the page>DOWNLOAD FOR OTHER PLATFORMS>SDK Tools Only) or get a slimmed version containing only the essential components here (Thanks @El Daddy)
Extract the zip and place the android-sdk-windows folder on the root of your hard drive. (the path should be like this: C:\android-sdk-windows)
**If you chose to download the slimmed sdk skip to step 5**
Only if you downloaded the full sdk: Go into the folder and run SDK Manager.exe. Install the following packages (there are a total of 4 packages):
- Tools > Android SDK Tools, Android SDK Platform-tools
- Extras > Android Support Library, Google USB Driver
Only if you downloaded the full sdk: Go back into the android-sdk-windows directory, and you should see a new folder named platform-tools. If not, repeat the step above.
Open a command prompt window and run "sysdm.cpl" (without the quotes) and a new window should popup. Go to the Advanced tab > Environmental Variables
Now focus your attention to the System variables box (the lower box). Scroll down and look for the Path variable > highlight it > click Edit > go all the way to the end of the Variable value text box, and paste the following entry:
Code:
;C:\android-sdk-windows\platform-tools
(OR WHATEVER PLATFORM-TOOLS DIRECTORY YOU PICKED)
Click OK then close all of the System Properties windows
You should now be able to use adb/fastboot commands no matter what location your command prompt is in. To confirm that it is indeed working, open a command prompt window and enter "adb version" (without the quotes). If it displays "Android Debug Bridge version x.x.xx" it is working. If it is gives an error saying that adb is not a recognized command, it has not been successful. Carefully repeat the steps above if this is the case.
Click to expand...
Click to collapse
The importance of being careful with your command choices.
MkVsTheWorld said:
"Be sure to use the CORRECT adb/fastboot commands, double-check the path on all commands, and double-check the existence of each file you are working with."
I hate to admit this, but I couldn't figure out why nothing was appearing in the device list when I did "adb devices", while the phone was in Fastboot. I did everything from A-Z and tore my hair out for 30 minutes until it hit me, my phone's in Fastboot. I've been messing with Android for 3+ years and made a newbie mistake lol.
Click to expand...
Click to collapse
Fixing MTP device not showing up after installing ADB drivers.
dbareis said:
I'm not sure what happened but on my WINDOWS 7 (64 bit) OS I had to modify "%WINDIR%\inf\wpdmtp.inf" as shown here: "http://forum.xda-developers.com/showpost.php?p=37930602&postcount=937". I then uninstall the device and drivers and performed a hardware scan to get it to work. I also added a "...PID_4EE2&MI_01" line but I am not positive that was required.
Hope that helps someone.
Click to expand...
Click to collapse
Whyzor said:
You should also mention what worked for me in post #16 (& confirmed by a few others in other threads). That is to toggle Settings - Storage - USB Connection type from Camera to Mass storage & also the debugging mode on & off.
Click to expand...
Click to collapse
Ashcunak said:
Op might wanna tack this onto the bottom of the main post as a last resort for folks to "start over" and be sure they have no old drivers installed.
http://www.nirsoft.net/utils/usb_devices_view.html
i had to use this program (right click run as admin if permissions are set) to remove EVERY single android related driver in order to get mine working.. turns out i had so many old ones in my system and some i couldn't remove from the device manager, the buttons wouldn't become click able..
Click to expand...
Click to collapse
CrazyIvan said:
I've tried everything and cannot get the authorization prompt to pop up on my Nexus5 so when I run adb devices the phone shows up as "unauthorized". Any suggestions? This is with updated sdk and USB drivers. Device manager shows phone as "Android Phone->Android Composite ADB Interface" and "Portable Device->Nexus 5". Tried toggling between MTP/PTP, USB Debugging on/off, stopping and starting the adb server (latest version 1.0.31).
Thanks in advance!
EDIT: Finally got the ba$tard! Run this for some adb debug logging:
adb kill-server
set ADB_TRACE=all
adb nodaemon server
Go and look back at the output from the start for any errors. In my case it couldn't mkdir in c:\users\administrator, which for me doesn't exist. I changed the Windows environment variable "ANDROID_SDK_HOME" to point to "C:\users\<my account dir>", closed the DOS window, re-ran the commands and I got prompted for the permission on my phone. Yee ha! Now I can fire up hello world with the SDK on my phone. Praise be to Google search for turning up this thread that told me about the debug logging.
Click to expand...
Click to collapse
SonicAngel said:
I just rooted my N5 (using the guide on this forum so I had no other drivers other than Google's SDK) and after unlocking my bootloader windows did not recognize my phone so I couldn't go further. Upon checking device manager I saw something called "AOSP on Hammerhead", a quick online search found a lot of very complicated answers (uninstall all drivers, restart, install adb drivers was one example).
Instead of all that I just right clicked "AOSP on Hammerhead", chose Update Driver, manually choose driver, went to "Android bootloader", chose the default driver from "Google inc" manually and that for some reason worked.
I figured this might help someone since the other solutions I found really were very long.
Click to expand...
Click to collapse
Questions? Ask below!
MaxRabbit said:
Reserved.
Questions? Ask below!
Click to expand...
Click to collapse
Hey man, thanks for the tutorial, I seem to still have trouble with this. Followed all the steps, even reset the device, to no avail. Anyone else having issues?
KTT16 said:
Hey man, thanks for the tutorial, I seem to still have trouble with this. Followed all the steps, even reset the device, to no avail. Anyone else having issues?
Click to expand...
Click to collapse
You're welcome! What shows up in your Device Manager now?
MaxRabbit said:
You're welcome! What shows up in your Device Manager now?
Click to expand...
Click to collapse
Hey thanks for the quick reply! I got it to work finally via: http://forum.xda-developers.com/showthread.php?t=2507905
Great tips and tutorial though..so stoked to have this phone!
KTT16 said:
Hey thanks for the quick reply! I got it to work finally via: http://forum.xda-developers.com/showthread.php?t=2507905
Great tips and tutorial though..so stoked to have this phone!
Click to expand...
Click to collapse
What step exactly did you take that fixed it?
MaxRabbit said:
What step exactly did you take that fixed it?
Click to expand...
Click to collapse
Open a command prompt window and run "sysdm.cpl" (without the quotes) and a new window should popup. Go to the Advanced tab > Environmental Variables
Now focus your attention to the System variables box (the lower box). Scroll down and look for the Path variable > highlight it > click Edit > go all the way to the end of the Variable value text box, and paste the following entry:
Code:
;C:\android-sdk-windows\platform-tools
Click OK then close all of the System Properties windows
You should now be able to use adb/fastboot commands no matter what location your command prompt is in. To confirm that it is indeed working, open a command prompt window and enter "adb version" (without the quotes). If it displays "Android Debug Bridge version x.x.xx" it is working. If it is gives an error saying that adb is not a recognized command, it has not been successful. Carefully repeat the steps above if this is the case.
KTT16 said:
Open a command prompt window and run "sysdm.cpl" (without the quotes) and a new window should popup. Go to the Advanced tab > Environmental Variables
Now focus your attention to the System variables box (the lower box). Scroll down and look for the Path variable > highlight it > click Edit > go all the way to the end of the Variable value text box, and paste the following entry:
Code:
;C:\android-sdk-windows\platform-tools
Click OK then close all of the System Properties windows
You should now be able to use adb/fastboot commands no matter what location your command prompt is in. To confirm that it is indeed working, open a command prompt window and enter "adb version" (without the quotes). If it displays "Android Debug Bridge version x.x.xx" it is working. If it is gives an error saying that adb is not a recognized command, it has not been successful. Carefully repeat the steps above if this is the case.
Click to expand...
Click to collapse
Ahh, your problem with my instructions then were that you weren't running ADB from inside the platform-tools folder
Definitely! I seriously got frustrated for a second and forgot how to read!
Sent from my Nexus 5 using XDA Premium 4 mobile app
Not showing up as removable storage
Hi, maybe you can help me.
Last night I unlocked my N5 using CF-Root, and flashed TWRP using Flashify. However, when I plug my N5 into my home computer it doesn't ever show up under 'My Computer' with other removable storage devices. It is present in the device manager under 'Android Phone -> Google Nexus ADB Interface'.
I've tried restrarting my computer, uninstalling the drivers and reinstalling them. Developer mode is enabled and if I switch from MTP to PTP then is shows up under removable storage, but I only have access to the DCIM folder. Switching back to MTP makes it disappear.
On my work computer it shows up correctly no problem.
My personal computer has had multiple installations of WugFresh Root toolkit and ADB/SDK files for my previous Galaxy Nexus and Nexus 7 but I uninstalled most of that before setting up the N5.
Thanks!
JonnyRock said:
Hi, maybe you can help me.
Last night I unlocked my N5 using CF-Root, and flashed TWRP using Flashify. However, when I plug my N5 into my home computer it doesn't ever show up under 'My Computer' with other removable storage devices. It is present in the device manager under 'Android Phone -> Google Nexus ADB Interface'.
I've tried restrarting my computer, uninstalling the drivers and reinstalling them. Developer mode is enabled and if I switch from MTP to PTP then is shows up under removable storage, but I only have access to the DCIM folder. Switching back to MTP makes it disappear.
On my work computer it shows up correctly no problem.
My personal computer has had multiple installations of WugFresh Root toolkit and ADB/SDK files for my previous Galaxy Nexus and Nexus 7 but I uninstalled most of that before setting up the N5.
Thanks!
Click to expand...
Click to collapse
same issue on my side...I canot use MTP only PTP...I also tryed new drivers from SDK but has not solved the problem
Alex
JonnyRock said:
Hi, maybe you can help me.
Last night I unlocked my N5 using CF-Root, and flashed TWRP using Flashify. However, when I plug my N5 into my home computer it doesn't ever show up under 'My Computer' with other removable storage devices. It is present in the device manager under 'Android Phone -> Google Nexus ADB Interface'.
I've tried restrarting my computer, uninstalling the drivers and reinstalling them. Developer mode is enabled and if I switch from MTP to PTP then is shows up under removable storage, but I only have access to the DCIM folder. Switching back to MTP makes it disappear.
On my work computer it shows up correctly no problem.
My personal computer has had multiple installations of WugFresh Root toolkit and ADB/SDK files for my previous Galaxy Nexus and Nexus 7 but I uninstalled most of that before setting up the N5.
Thanks!
Click to expand...
Click to collapse
This is a really strange problem :-/ what does it show up as when you are in device manager on your work computer?
MaxRabbit said:
This is a really strange problem :-/ what does it show up as when you are in device manager on your work computer?
Click to expand...
Click to collapse
It shows up as a 'Portable Device' -> 'Portable Media Player' (I was thinking it was a 'Device with Removable Storage').
I have full access to the internal file folders here at work.
Here's a suggestion for something to add to the OP.
"Be sure to use the CORRECT adb/fastboot commands, double-check the path on all commands, and double-check the existence of each file you are working with."
I hate to admit this, but I couldn't figure out why nothing was appearing in the device list when I did "adb devices", while the phone was in Fastboot. I did everything from A-Z and tore my hair out for 30 minutes until it hit me, my phone's in Fastboot. I've been messing with Android for 3+ years and made a newbie mistake lol.
Sent from my Nexus 5 using Tapatalk
JonnyRock said:
Hi, maybe you can help me.
Last night I unlocked my N5 using CF-Root, and flashed TWRP using Flashify. However, when I plug my N5 into my home computer it doesn't ever show up under 'My Computer' with other removable storage devices. It is present in the device manager under 'Android Phone -> Google Nexus ADB Interface'.
I've tried restrarting my computer, uninstalling the drivers and reinstalling them. Developer mode is enabled and if I switch from MTP to PTP then is shows up under removable storage, but I only have access to the DCIM folder. Switching back to MTP makes it disappear.
On my work computer it shows up correctly no problem.
My personal computer has had multiple installations of WugFresh Root toolkit and ADB/SDK files for my previous Galaxy Nexus and Nexus 7 but I uninstalled most of that before setting up the N5.
Thanks!
Click to expand...
Click to collapse
I have the same problem and done the same exact things u did. any help?
I'm having no luck with unlocking bootloader of my Nexus 5 today. I've unlocked previous Android devices fine, but this one for some reason it's not detecting it in USB drivers. It shows as Other devices -> Nexus 5 in device manager, but when I select update driver & navigate to the dir where Android SDK/extras/google/usb_driver
Windows was unable to install your Nexus 5
Windows could not find driver software for your device.
I updated the OTA that came right away earlier, maybe this caused the Windows USB drivers to not work match the updated OTA build? Is there a way to ensure that old windows driver is uninstalled? I can only select 'uninstall', but not the 'remove old driver files' some docs mention. Also when I connect my Nexus 4 it's fine, and enabling debugging mode prompts for to allow the security fingerprint of the PC. But this prompt doesn't appear on Nexus 5, not sure if it's supposed to happen AFTER the PC is able to communicate with the N5 or not, which is the step that I'm stuck on. Tried it on another Windows 7 system and same problem.
UPDATE: Well my Nexus 4 worked fine along with adb until a few minutes ago, after toggling the Debugging Mode on the phone, it's not recognized on Windows now either. So definitely think it's a Windows 7 or Google USB Driver issue. Any pointers on how to start over (without reinstalling Windows) would be appreciated.
UPDATE 2: For future reference, I got around my Windows driver issue by going into Nexus - Settings - Storage - USB computer connection, toggle to Camera (PTP) and Media device (MTP), that reinitialized windows to recognize it in Device Manager again. Stupid Windows.
aluxzen said:
same issue on my side...I canot use MTP only PTP...I also tryed new drivers from SDK but has not solved the problem
Alex
Click to expand...
Click to collapse
I'm not sure what happened but on my WINDOWS 7 (64 bit) OS I had to modify "%WINDIR%\inf\wpdmtp.inf" as shown here: "http://forum.xda-developers.com/showpost.php?p=37930602&postcount=937". I then uninstall the device and drivers and performed a hardware scan to get it to work. I also added a "...PID_4EE2&MI_01" line but I am not positive that was required.
Hope that helps someone.
Whyzor said:
UPDATE 2: For future reference, I got around my Windows driver issue by going into Nexus - Settings - Storage - USB computer connection, toggle to Camera (PTP) and Media device (MTP), that reinitialized windows to recognize it in Device Manager again. Stupid Windows.
Click to expand...
Click to collapse
That... Thankyou for that info.
I was able to get ADB to work but was not able to get the device to popup as a storage device. That fixed it. Thanks!
I'm not sure what happened but on my WINDOWS 7 (64 bit) OS I had to modify "%WINDIR%\inf\wpdmtp.inf" as shown here: "http://forum.xda-developers.com/show...&postcount=937".
Click to expand...
Click to collapse
Thanks, that link was really helpful! I struggled with the correct detection before (seems I had some old drivers for my last phone on that windows installation...)
Whyzor said:
I'm having no luck with unlocking bootloader of my Nexus 5 today. I've unlocked previous Android devices fine, but this one for some reason it's not detecting it in USB drivers. It shows as Other devices -> Nexus 5 in device manager, but when I select update driver & navigate to the dir where Android SDK/extras/google/usb_driver
Windows was unable to install your Nexus 5
Windows could not find driver software for your device.
I updated the OTA that came right away earlier, maybe this caused the Windows USB drivers to not work match the updated OTA build? Is there a way to ensure that old windows driver is uninstalled? I can only select 'uninstall', but not the 'remove old driver files' some docs mention. Also when I connect my Nexus 4 it's fine, and enabling debugging mode prompts for to allow the security fingerprint of the PC. But this prompt doesn't appear on Nexus 5, not sure if it's supposed to happen AFTER the PC is able to communicate with the N5 or not, which is the step that I'm stuck on. Tried it on another Windows 7 system and same problem.
UPDATE: Well my Nexus 4 worked fine along with adb until a few minutes ago, after toggling the Debugging Mode on the phone, it's not recognized on Windows now either. So definitely think it's a Windows 7 or Google USB Driver issue. Any pointers on how to start over (without reinstalling Windows) would be appreciated.
UPDATE 2: For future reference, I got around my Windows driver issue by going into Nexus - Settings - Storage - USB computer connection, toggle to Camera (PTP) and Media device (MTP), that reinitialized windows to recognize it in Device Manager again. Stupid Windows.
Click to expand...
Click to collapse
Thank you for sharing your solution.
I have read many guides about setting up and using ADB, I am using an older computer with windows xp sp3. I just got my first nexus device which is a nexus 5, in device manager the phone shows up as " samsung android phone" and then "google nexus adb interface". I have tried uninstalling and then reinstalling the drivers using many different ones found on xda. I have the android sdk installed and adb seems to be working, at least when I type in "adb version" the version number comes up, but when I type "adb devices" nothing comes up as attached devices. This is really frustrating me, as I have have been trying to get this working for days now.i have already uninstalled every other android related driver using USBDeview. If anyone could please help me with this I would greatly appreciate it. I'm almost to the point go giving up! Could the problem be because I rooted the phone before getting all this setup? I ask this because when I try to update the driver in device manager it always shows driver type as clockwork mod no matter what driver I try to use
Did you enable ADB via Dev Options on the phone?
theesotericone said:
Did you enable ADB via Dev Options on the phone?
Click to expand...
Click to collapse
Do you mean USB debugging, yes I have that enabled
Go to device manager select your phone (samsung device or whatever it's showing!!) and right click and select "Update Driver Software".
On the next screen, select "Browse my computer for driver software" and set the path to : C:\Program Files (x86)\Android\android-sdk\extras\google\usb_driver"
I have used C:\Program Files (x86) because that's the place in which I have installed the SDK. Put a tick mark on "Include subfolders" and then hit Next...
Your device drivers will be installed again and adb will be working!
PS: Please make sure you have the latest android sdk and usb_driver downloaded from SDK manager!!
I am actually following the steps from the pwnieexpress guide to build my own pwn phone, in an attempt to build my own pwn phone. With no malicious intent, I'm trying to build up my pentest skills on the go.
I'm currently on Windows 7 using the android sdk. Fastboot devices manage to return my device but on step 13, my adb devices shows blank in the list of devices.
When I plugged in my wiped out nexus 5, device manager shows the Google nexus adb driver, but I cannot seem to get the adb devices to show my device.
I tried restarting the adb server and reconnecting my device to multiple USB ports but doesn't seem to work.
Any ideas? I've yet to try on a different machine, but could it be a problem with the ports?
Looking forward for any help available.
Don't slam me for asking the obvious, but do you have USB debugging ticked on in the os settings? You may have to go through an update of the android composite adb interface drivers via device manager. Just choose to browse computer, pick from a list, then run the update on each item listed. This doesn't install anything new but does seem to reset drivers. Beyond that, can't help.
Sent from my Nexus 9 using Tapatalk
Fixed. Seem to be a problem with the usb drives on my home PC, it failed to detect the device during adb devices. Weird, as fastboot seemed to work out well.
I basically installed the drivers in another machine and adb devices and adb push .. /sdcard/ worked just fine.
Thanks!