Related
Hi there,
I need your help urgently.
I received a brand new TF700T and did make it work to support root.
I also did unlock the bootrom protection.
When I tried to install a custom ROM manager (Clockwork Mod) image from:here
The device didn't want to start any more - showing message:
The Device ist Unlocked.
Android cardhu-user bootloader <2.10 e> released by "TW_epad-9.4.5.22-20120615" A03
Checking for android ota recovery
Booting recovery kernel image
But nothing happens anymore (
I can wait for the battery to run empty in this mode.
There' no chance to boot from Micro SD.
The only thing what works at the moment is to connect the device via APX drivers.
I tried to communicate with device via NVFLASH tool
But when trying this - I get the message:
Nvflash started
Unknown Device found
Does any one have an idea where to find appropriate drivers for Nvflash?
Or the parameters to match TF700T?
Thanks in advance!
if you are able to access APX then you still have hope, first of all you need to push custom recovery like TWRP via fastboot mode and then install custom ROM. Most likelly you were to lazy to read a lot information on this forum how to install stuff properlly.
EDIT: if Tf700t has pin hole you should turn it off despite waiting for it to discharge...
nikoltu said:
if you are able to access APX then you still have hope, first of all you need to push custom recovery like TWRP via fastboot mode and then install custom ROM. Most likelly you were to lazy to read a lot information on this forum how to install stuff properlly.
EDIT: if Tf700t has pin hole you should turn it off despite waiting for it to discharge...
Click to expand...
Click to collapse
I did already read a lot - for hours and nights.
But my main problem is: UNKNOWN DEVICE
What does TWRP mean? How do I get fastboot to work?
I'm even not allowed to enter recovery mode.
The device is just recognized as an APX -device...
I can't push or download any custom ROM since I can't communicate with the device in both directions...
For those who messed up really bad and can't boot but are unlocked.
EDIT: I didn't see that you are not unlocked. then you should Power on + volume down, wait, see two icons select wipe, pray to god it helped or not. And if it doesn't boot and you are not unlocked last thing to do is RMA.
You are not allowed to enter recovery because you have stock one with droid dead and red triangle I guess.This is TWRP site and all instructions are here TWRP - Team Win Recovery Project is alternative to ClockworkMod Recovery but better. to get to fast boot turn on your tab holding power on + volume down and then do nothing while it asks to pres up. if you are unlocked you will see 3 icons select usb drive icon. FASTBOOT mode. now follow instructions from TWRP site. after that youl need custom rom zip. if recovery instaled successfuly and you can get into it you'll need to put custom ro into microSD or if you can into internal storage. if you can't conect to pc via cable and start cmd if Windows or terminal if Linux or mac. type
Code:
adb shell
mount /dev/block/mmcblk1p1 /data/media
you will be able to access microSD via recovery (unless it is different than Prime tf201 you will need different command, but give it a try)
nikoltu said:
EDIT: I didn't see that you are not unlocked. then you should Power on + volume down, wait, see two icons select wipe, pray to god it helped or not. And if it doesn't boot and you are not unlocked last thing to do is RMA.
You are not allowed to enter recovery because you have stock one with droid dead and red triangle I guess.This is TWRP site and all instructions are here TWRP - Team Win Recovery Project is alternative to ClockworkMod Recovery but better. to get to fast boot turn on your tab holding power on + volume down and then do nothing while it asks to pres up. if you are unlocked you will see 3 icons select usb drive icon. FASTBOOT mode. now follow instructions from TWRP site. after that youl need custom rom zip. if recovery instaled successfuly and you can get into it you'll need to put custom ro into microSD or if you can into internal storage. if you can't conect to pc via cable and start cmd if Windows or terminal if Linux or mac. type
Code:
adb shell
mount /dev/block/mmcblk1p1 /data/media
you will be able to access microSD via recovery (unless it is different than Prime tf201 you will need different command, but give it a try)
Click to expand...
Click to collapse
Thanks for advise - BUT
I have no choice like selecting Fastboot or USB etc. with volume buttons.
These options unfortunately do not come up anymore.
My device is definetly unlocked. It shows up "Device unlocked" when trying to boot normally.
When trying to go to recovery, with Volume - hold, the device tries to launch to recovery but hangs in status:
Device is Unlocked
Android cardhu-user bootloader (2.10 e) released by "TW_epad-9.4.5.22-20120615" A03
Checking for android ota recovery
Booting recovery kernel.
I have NO option to go to fastboot! Only way will be APX but nvflas always tell me unknown device.
So I was looking for any other version of nvflash.
In other forum I did find hint for nvflash ICS but didn't find right version yet.
If I only could get communication via APX worked to my device, then I could send data via nvflash and APX...
I assume you can't even go to rom as it bootloops on EEE pad screen not on rom splash screen
1. Did you try Wipe option in (power + volume down, wait 5 sec.)? [it is esential in all situations of trying to recover]
2.ammm... when you enter "adb devices" in your cmd on PC doesn't it show anything (do it while your tablet is on and hangs anywhere, just make sure it is on)? list is empty? if not it shows your device with some random letters and numbers.
Try manually setting your pc. Download android SDK and all packages for Android 4.x then in Device Manager (Control panel) find your Tablet and update your driver to Android ADB interface (you can experiment, till your device is shown correctly via adb devices command).
But first of all make sure you do or did first step. it is common issue among Prime users so maybe it can help you.
nikoltu said:
I assume you can't even go to rom as it bootloops on EEE pad screen not on rom splash screen
1. Did you try Wipe option in (power + volume down, wait 5 sec.)? [it is esential in all situations of trying to recover]
2.ammm... when you enter "adb devices" in your cmd on PC doesn't it show anything (do it while your tablet is on and hangs anywhere, just make sure it is on)? list is empty? if not it shows your device with some random letters and numbers.
Try manually setting your pc. Download android SDK and all packages for Android 4.x then in Device Manager (Control panel) find your Tablet and update your driver to Android ADB interface (you can experiment, till your device is shown correctly via adb devices command).
But first of all make sure you do or did first step. it is common issue among Prime users so maybe it can help you.
Click to expand...
Click to collapse
I would like to exchange email-adresses to enhance communication.
You could also send email to [email protected]
I did try with button combination (power & + button) as well, but device did not wipe.
For now - I'm about to update Android SDK )
Hopefully this works to recognize my TF700T...
If you manage to unbrick please post the information back here it may be helpful to others.
t-liner said:
My device is definetly unlocked. It shows up "Device unlocked" when trying to boot normally.
Click to expand...
Click to collapse
How did you get your TF700 unlocked? Asus hasn't posted an unlock tool for it yet that I could find.
Asus devices have the same unlock tool
Sent from my Transformer Prime TF201 using xda app-developers app
nikoltu said:
Asus devices have the same unlock tool
Sent from my Transformer Prime TF201 using xda app-developers app
Click to expand...
Click to collapse
Unlock + Root was never a problem.
I managed it to unlock the device using the TF300T tool / link.
Boot loop was big problem.
I did raise RMA in the meantime. New device is on the way.
Thanks to all repliers.
I will keep off doing this again / wait until xda-experts will provide a working way to CWM TF700T.
My Transformer Infinity isn't bricked, I just can't get it to boot into recovery. (I'm unlocked and rooted, but no custom ROM.) I have tried both CWM and TWRP 2.2.0 with GooManager. The tablet just won't boot into recovery mode. I can hold the Down Volume key and Power button to have the initial boot up menu display. When I press the Up Volume button to boot into recovery mode, it just hangs like the OP talks about. I then have to hold the power button for about five or so seconds to get it to power down again. I can turn it back on and it will boot normally.
I thought maybe something was messed up because I installed busybox, or hacked the Flash Player to work in desktop mode, or tweaked the build.prop file or something. I've put the build.prop file back to default, and removed the busybox apps, but that hasn't resolved the problem. I've tried re-running the unlock tool, but it fails halfway through. I'm not sure if that's normal or not after you've run it once, or an indication of something messed up.
Any suggestions on what else to try or look at are appreciated.
---------- Post added at 06:06 PM ---------- Previous post was at 05:13 PM ----------
UPDATE: I finally got TWRP 2.2.2.0 to work using the following option from the Instruction Page (http teamw.in/project/twrp2/105):
Download - ADB / Terminal method:
Download the above file. Save it to the root of your /sdcard directly (internal memory only) and rename it to twrp.blob
Launch terminal emulator or connect to your computer and open an adb shell, then type the following:
su
dd if=/sdcard/twrp.blob of=/dev/block/mmcblk0p4
Then reboot to complete installation.
stuck at boot logo
Im having the same issue, i was playing around with black baked bean roms i just installed early that day and i wanted to switch twrp to cwm and by deleting goo manger to get roms manger and install the recovery mod but damn i notice it say asus transformer prime and not infinity noe that think about i thats the reason i cant get into reboot recovery mode damn i fuk up bad. okay so i did the stock recovery boot mode got into that i i remember seeing in this post that someone say try to wipe data and i did that and now im juss stuck asus logo and with
(The Device ist Unlocked.)
Android cardhu-user bootloader <2.10 e> released by "TW_epad-9.4.5.22-20120615" A03
Checking for android ota recovery
Booting recovery kernel image
im just there and when i try to plug into my pc it shut down by self, i even wait till the battery die and hope to god that it well reboot itself and pwaw it reboot nope that ****..can any one please tell what i did wrong or didnt do it would help me alot .THanks a million in advanced
dough30i said:
Im having the same issue, i was playing around with black baked bean roms i just installed early that day and i wanted to switch twrp to cwm and by deleting goo manger to get roms manger and install the recovery mod but damn i notice it say asus transformer prime and not infinity noe that think about i thats the reason i cant get into reboot recovery mode damn i fuk up bad. okay so i did the stock recovery boot mode got into that i i remember seeing in this post that someone say try to wipe data and i did that and now im juss stuck asus logo and with
(The Device ist Unlocked.)
Android cardhu-user bootloader <2.10 e> released by "TW_epad-9.4.5.22-20120615" A03
Checking for android ota recovery
Booting recovery kernel image
im just there and when i try to plug into my pc it shut down by self, i even wait till the battery die and hope to god that it well reboot itself and pwaw it reboot nope that ****..can any one please tell what i did wrong or didnt do it would help me alot .THanks a million in advanced
Click to expand...
Click to collapse
Trying to flash the new CWM recovery, too. Mine gets stuck in the bootloader menu (where you have to choose between Wipe, fastboot mode, and cold startup). Every time I select fastboot it says "starting fastboot usb protocol" and just hangs there.
gaxiolafm said:
Trying to flash the new CWM recovery, too. Mine gets stuck in the bootloader menu (where you have to choose between Wipe, fastboot mode, and cold startup). Every time I select fastboot it says "starting fastboot usb protocol" and just hangs there.
Click to expand...
Click to collapse
Damn u too huh. **** I just got mine for only 2 week old and neva thought I go through this IDK what to do but wait gracefully for the senior member to help or come up with a way for us noobie to unbrick my 650 table...Oh BTW leave it alone then u still lucky if can go thru fast boot mode
I have the exact same problem
anyone has a solution to this problem
gaxiolafm said:
Trying to flash the new CWM recovery, too. Mine gets stuck in the bootloader menu (where you have to choose between Wipe, fastboot mode, and cold startup). Every time I select fastboot it says "starting fastboot usb protocol" and just hangs there.
Click to expand...
Click to collapse
That is what it says when you are in fastboot mode, the rest of the job you do with a computer. Also we have had major issues with cwm on the Prime, I would recommend TWRP!
Sent from my Transformer Prime TF201 using xda premium
Same problem
israodin said:
I have the exact same problem
anyone has a solution to this problem
Click to expand...
Click to collapse
Same problem.
Any help? Please! :crying:
Hi there, Can anyone help me to unrick my tf300, its stuck on the logo screen.
I have try many things, some guys from hong kong tell me i have to use APX mode to sort the problems out, I manage so far.
Drivers I download the is Universal_Naked_Driver_0.7, also use nvflash drivers, both I try. i still get te samethings when I try to use the nvflash
I turn on tf300 with volume up, few seconds the screen went blank, and hear a beep from my pc, so is connect alright.
I type download.bat command, with prime 1.4 rom in the same folder. after few seconds I get
nvflash start
unknow usb found.
Can anyone tell me what i done wrong here.
can someone show me some step by step.
otherwise is a waste of money, the tf300 not working.
THankyou
acelaw said:
Hi there, Can anyone help me to unrick my tf300, its stuck on the logo screen.
I have try many things, some guys from hong kong tell me i have to use APX mode to sort the problems out, I manage so far.
Drivers I download the is Universal_Naked_Driver_0.7, also use nvflash drivers, both I try. i still get te samethings when I try to use the nvflash
I turn on tf300 with volume up, few seconds the screen went blank, and hear a beep from my pc, so is connect alright.
I type download.bat command, with prime 1.4 rom in the same folder. after few seconds I get
nvflash start
unknow usb found.
Can anyone tell me what i done wrong here.
can someone show me some step by step.
otherwise is a waste of money, the tf300 not working.
THankyou
Click to expand...
Click to collapse
You flashed a PRIME rom to your tf300?
First of all, we should know which firmware do you have before your tablet doesn't boot (Stock ICS, JB, Custom Rom).
Then, you can use fastboot to recover your tablet (i did it a lot of times). Try steps below:
1. Download latest oficial Asus firmware (V10.4.2.13). BE SURE to download your region (WW, US, etc...)
2. Extract downloaded zip and take blob file.
3. Download Android SDK and install them on C:\ (http://developer.android.com/sdk/index.html)
4. Execute SDK downloader and mark tools and platform-tool options for download.
5. OPTIONAL add tools and platform-tool folder to PATH, after that test if fastboot command runs on CMD.
6 Copy blob file on same SDK folder.
7. Connect TF300T with usb cable and put it in Download Mode (USB icon on recovery menu)
8. Wait until drivers are installed.
7. Open CMD, go to Android SDK folder and then type command below:
fastboot -i 0x0B05 flash system blob
wait 2 or 3 minutes and then you'll see a message that send and write was OK. Now type this command:
fastboot -i 0x0B05 reboot
And It should boot again.
ppmeis said:
First of all, we should know which firmware do you have before your tablet doesn't boot (Stock ICS, JB, Custom Rom).
Then, you can use fastboot to recover your tablet (i did it a lot of times). Try steps below:
1. Download latest oficial Asus firmware (V10.4.2.13). BE SURE to download your region (WW, US, etc...)
2. Extract downloaded zip and take blob file.
3. Download Android SDK and install them on C:\ (http://developer.android.com/sdk/index.html)
4. Execute SDK downloader and mark tools and platform-tool options for download.
5. OPTIONAL add tools and platform-tool folder to PATH, after that test if fastboot command runs on CMD.
6 Copy blob file on same SDK folder.
7. Connect TF300T with usb cable and put it in Download Mode (USB icon on recovery menu)
8. Wait until drivers are installed.
7. Open CMD, go to Android SDK folder and then type command below:
fastboot -i 0x0B05 flash system blob
wait 2 or 3 minutes and then you'll see a message that send and write was OK. Now type this command:
fastboot -i 0x0B05 reboot
And It should boot again.
Click to expand...
Click to collapse
but fastboot need a unlocked bootloader, no?
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
Yes, that's right, but I suppost if he tries to flash a custom rom he has already unlocked his device. You can't flash any rom without unlock bootloader.
I cant do anything apart from get on to apx mode, from apx mode how do I use command to flash back.
My tf300 is ics, unlock.
when i connect usb to pc. i press power and volume up. thats only things i can do.
so what do i do next?
thanks.
The same problem.
I only see: "device is unlocked" or something like that. And nothing go on.
Is it totaly bicked or is there any chance to restore it?
Please advice.
Did anybody ever figure this out. I'm in the same boat. Can't do vol down+power to get to recovery. But if i do volume up+power it shows in device manager as transformer prime apx interface (even though it's just a tf300)
bigworm82 said:
Did anybody ever figure this out. I'm in the same boat. Can't do vol down+power to get to recovery. But if i do volume up+power it shows in device manager as transformer prime apx interface (even though it's just a tf300)
Click to expand...
Click to collapse
Try this link.
http://forum.xda-developers.com/showthread.php?t=2034866
no way to unbrick tf300t
Funny, I bricked my tf300t without doing anything. One day it just got stuck in asus screen.
tried to recover, nothing happended.
tried hard reset. Nothing.
Wipe data: result: bricked tablet.
I'm looking for information it is defintely impossible to unbrick it.
Anybody else with the same situation can tell you that.
Nobody has even been able to do it.
If you send it to Asus they provide a new tablet.
Conclusion:
TF300T is a terrible product, as any other asus product i assume. Amazing that you can brick a tablet without even trying to flash it or without even being connected to a computer.
It bricks by itself. Hundreds of other users can confirm it.
My advice: dont by asus products
If you already have one, dont use wipe data as anybody who has done it has ended up with an expensive useless brick.
Odp: [Q] How to unbrick my tf300
I don't agree witch this, only think what you not should use is t the wipe data from bootloader menu - I already flashed many times not working kernel, get really often bootloop - the problem is - much users going to made stupid things when the get a soft bootloop - If you get this first try wipe data from recovery, if this won't help, try to format data from recovery - often happends that the ext4 filessystem get broken. Recovery should allowa us to run fsck on data - I fixed my bootloops many times with it without loosing my data.
Sent from my GALAXY Cooper
OP,
I think your anger is misdirected. The device, as it comes out of the box, works 100% without issues. YOU as a user decided to make changes that could potentially brick it. YOU chose to follow the steps with the full disclaimer that it can/may brick your device. So at the end of the day, its' not the fault of ASUS or the device for "bricking itself"; the responsibility of your actions lies on your own shoulders.
That being said, Asus will not provide warranty support for a tablet that has been unlocked. This is clearly stated in their unlocker app. So no, they won't "send you a new tablet" if you send it to them (unless you pay out of pocket for the repairs).
I've done just about as bad of a brick as I possibly can on my tablet and recovered just fine. It was just a matter of being CAREFUL, reading instructions three times before l followed them, and asking lots of questions. But what ultimately saved me was the NVFlash tool, and for that I am eternally grateful.
Just my two cents.
opethfan89 said:
OP,
I think your anger is misdirected. The device, as it comes out of the box, works 100% without issues. YOU as a user decided to make changes that could potentially brick it. YOU chose to follow the steps with the full disclaimer that it can/may brick your device. So at the end of the day, its' not the fault of ASUS or the device for "bricking itself"; the responsibility of your actions lies on your own shoulders.
That being said, Asus will not provide warranty support for a tablet that has been unlocked. This is clearly stated in their unlocker app. So no, they won't "send you a new tablet" if you send it to them (unless you pay out of pocket for the repairs).
I've done just about as bad of a brick as I possibly can on my tablet and recovered just fine. It was just a matter of being CAREFUL, reading instructions three times before l followed them, and asking lots of questions. But what ultimately saved me was the NVFlash tool, and for that I am eternally grateful.
Just my two cents.
Click to expand...
Click to collapse
I have problem that my partitions won't mount at all. I have access to fastboot, CWM, and adb but no matter what i cannot access my partitions and so i cannot install zip from CWM. When i try blob within fastboot my tablet just freezes.....
Hi, what happens if I have no access to fastboot? It loops in the ASUS logo and what ever I do, can't gain access to recovery because it doesn't get into fastboot. So how to solve it via APX? Thank you.
You wont solve the problem unless youve done a nvflash backup. If you tablet is recognised as APX while plugged in PC, then you have an unrecoverable brick. If nothing appears when you plug it, then try on another PC.
Sent from my TF300T using xda premium
unbrick tf300
ilyuha1108 said:
You wont solve the problem unless youve done a nvflash backup. If you tablet is recognised as APX while plugged in PC, then you have an unrecoverable brick. If nothing appears when you plug it, then try on another PC.
Sent from my TF300T using xda premium
Click to expand...
Click to collapse
Hi,
I am having a similar problem to the one described. I have unvblocked my TF300T and installed CWM recovery (v. 6.0.2.3), but it can't mount any filesystem, so I can not flash anything. The boot menu is gone (RCK, wipe tablet, android) and when I switch the tablet on It just goes to CWM. If I connect the tablet to a PC, I can send commands with adb from my win 7 PC (for instance "adb reboot" will reboot the tablet), but fastboot doesn't work (it keeps "waiting for device"). Prior to this my android version was JB 4.2. I didn't make any backup, so I am fearing the worst outcome. Did I brick my tablet for good?
Thanks a lot for any reply.
TF300T blocked on boot screen
hello everybody,
my name is jonathan, and i have a very big problem.
My Asus TF300t is blocked on boot screen after try to install a new rom on JB 4.2.2.
>My clockworkMod reconvery is v6.0.1.0.
I tried to install several roms, offical or not but the problem is the same, "The device is unlocked" on the boot screen Asus...
I read the previously posts and :
- i installed on my pc the sdk
- i dowload the "blob" file and i placed it on tools directory
- but, the actually problem is whis the lign "fastboot -i OxOBO5.... (i have copied and paste it on schell command) and enter
load_file: could not allocate 820157833 bytes
error: cannot load "blob": not enough space
can you help me please ?
i want to resolve this problem with you to install the best rom for this model.
Thank you very much and sorry for my english, i am french but i understand your paragraph.
See you soon
Jonathan
If you have mounting / PIT errors you could try my solution as described here:
http://forum.xda-developers.com/showpost.php?p=44244313&postcount=12
no guarantee though but it basically wipes your device so that you should be able to flash the blob file back.
also if your tab still is ICS- check if you are using the correct recovery - also bear in mind that cm10.1 afaik uses the new 4.2 bootloader and probably wont work with ics based PIT devices.
gl
same problem of space
Buster99 said:
If you have mounting / PIT errors you could try my solution as described here:
http://forum.xda-developers.com/showpost.php?p=44244313&postcount=12
no guarantee though but it basically wipes your device so that you should be able to flash the blob file back.
also if your tab still is ICS- check if you are using the correct recovery - also bear in mind that cm10.1 afaik uses the new 4.2 bootloader and probably wont work with ics based PIT devices.
gl
Click to expand...
Click to collapse
Hello man,
I try your method but the problem is the same when i want to copy the blob file, "not enough space ..."
fastboot erase system OK
fastboot erase recovery OK
fastboot erase userdata OK
fastboot erase boot OK
fastboot erase misc OK
fastboot erase cache OK
fastboot -i 0x0B05 flash system c:\adb\TF300t\blob PROBLEM
The message is the same like previously, always the problem of space.
I tries the method by copy the blob file on different directory on my computer and on a usb key too.
Always the same problem of space
I think the problem is the space on the tablet but i dont' understand. I erase system, recovery, userdata, boot, misc, cache, i think the tablet is empty.
Can you help me please ?
Thank you very much
Jonathan
which blob file did you use? Was the zip appropriate for your region? also what was the last stock rom version you ran - you said you wanted to update to 4.2.2 - what was the old version?
-Buster
Hello there!
I have a TF700T pad, I installed free rom manager application, from within that application I chose to install clockworkmod recovery, the application loaded the clockworkmod recovery from the internet (there was an indicator on top of the application screen).
After finished, I rebooted into recovery, but it doesn't reboot to recovery, it loads android normally, then I tried to boot to recovery manually by pressing and holding the the power button along with the volume down button it loads nothing and stays there for ever!! I did this several times then it it changed and now it doesn't even load the android normally.
And when I boot into APX mode, the adb can't find it!
In short, I can't access recovery nor system!
When I try to boot to recovery
(power + volume down) It freezs and the following shows on the screen:
"The device is unlocked.
Android cardhu-user bootloader <2.10 e> release by "CN_epad-9.4.5.30-20120907" A03
Checking for android ota recovery
Booting recovery kernel image"
- I downloaded the firmware from ASUS and renamed it to "EP201_768_SDUPDATE" and copied to the root of a formated FAT32 micro SD card and tried to boot, but still freezing on above mentioned screen.
- The PC recognizes it (drivers are correct, i downloaded them and installed them) but the adb can not find the pad and tells me to install tap's specific drivers!
- I tried to flash the recovery image image.img through adb, but same problem, it stays there for ever showing the message "waiting for device".
Please, help me with a solution for that situation!
Thank you.
shreef said:
Hello there!
I have a TF700T pad, I installed free rom manager application, from within that application I chose to install clockworkmod recovery, the application loaded the clockworkmod recovery from the internet (there was an indicator on top of the application screen).
After finished, I rebooted into recovery, but it doesn't reboot to recovery, it loads android normally, then I tried to boot to recovery manually by pressing and holding the the power button along with the volume down button it loads nothing and stays there for ever!! I did this several times then it it changed and now it doesn't even load the android normally.
And when I boot into APX mode, the adb can't find it!
In short, I can't access recovery nor system!
When I try to boot to recovery
(power + volume down) It freezs and the following shows on the screen:
"The device is unlocked.
Android cardhu-user bootloader <2.10 e> release by "CN_epad-9.4.5.30-20120907" A03
Checking for android ota recovery
Booting recovery kernel image"
- I downloaded the firmware from ASUS and renamed it to "EP201_768_SDUPDATE" and copied to the root of a formated FAT32 micro SD card and tried to boot, but still freezing on above mentioned screen.
- The PC recognizes it (drivers are correct, i downloaded them and installed them) but the adb can not find the pad and tells me to install tap's specific drivers!
- I tried to flash the recovery image image.img through adb, but same problem, it stays there for ever showing the message "waiting for device".
Please, help me with a solution for that situation!
Thank you.
Click to expand...
Click to collapse
Do you have nvflash backup? if not, I believe you're done. You need to send out for repair.
Thank you for your quick response!
Isn't there any other way I could repair it without sending to ASUS repair?? i originally bought it from CHINA and now i am here in EGYPT!!!
shreef said:
Thank you for your quick response!
Isn't there any other way I could repair it without sending to ASUS repair?? i originally bought it from CHINA and now i am here in EGYPT!!!
Click to expand...
Click to collapse
I'm assuming you've unlocked the bootloader. Can you get the device into fastboot and push a new recovery through that?
shreef said:
Thank you for your quick response!
Isn't there any other way I could repair it without sending to ASUS repair?? i originally bought it from CHINA and now i am here in EGYPT!!!
Click to expand...
Click to collapse
ArmyAg08 said:
I'm assuming you've unlocked the bootloader. Can you get the device into fastboot and push a new recovery through that?
Click to expand...
Click to collapse
That would be the only remaining option, but ROM Manager is known to do this. If a user cannot even read on a forum before doing stuff, I'm not sure this is going to work out very well.
OK. I'll go back to my hermit cave now.
No, I can only boot in APX mode!
Isn't there any way we can make the adb reconize and access the PAD?
I can bring the recovery image and put in the root of the SD card, but what should I name it so the boot can reconize it and update? (the device says "checking for android ota recovery" !!
shreef said:
No, I can only boot in APX mode!
Isn't there any way we can make the adb reconize and access the PAD?
I can bring the recovery image and put in the root of the SD card, but what should I name it so the boot can reconize it and update? (the device says "checking for android ota recovery" !!
Click to expand...
Click to collapse
APX is NOT adb -- you need to issue commands using fastboot. Did you use the manufacturer's switch? "adb devices" won't return anything, even on a perfectly healthy 700. Take a look here:
http://forum.xda-developers.com/showthread.php?t=1926286
and don't forget to use that switch: -i 0x0B05, as in
fastboot -i 0x0B05 <command>
For example, fastboot -i 0x0B05 devices or fastboot -i 0x0B05 reboot
EDIT: APX = FASTBOOT, for clarity.
MartyHulskemper said:
That would be the only remaining option, but ROM Manager is known to do this. If a user cannot even read on a forum before doing stuff, I'm not sure this is going to work out very well.
OK. I'll go back to my hermit cave now.
Click to expand...
Click to collapse
I only asked because I thought ROM manager was known to brick this tablet if you tried to install a recovery with it. I may be mistaken though.
Sent from my ASUS Transformer Pad TF700T
MartyHulskemper said:
APX is NOT adb -- you need to issue commands using fastboot.
Click to expand...
Click to collapse
APX is also NOT fastboot - in APX mode you can *only* use nvflash, but for that you'd need to have created the blob before bricking.
I am sorry, I didn't really understand what you are trying to say!!
What does "manfacturer's switch" mean?
Also, what does APX = FASTBOOT ?
shreef said:
I am sorry, I didn't really understand what you are trying to say!!
What does "manfacturer's switch" mean?
Also, what does APX = FASTBOOT ?
Click to expand...
Click to collapse
shreef, the short answer is that only ASUS can help you now. I believe that is your only solution.
I'm so sorry.
OK, I have sent it to ASUS!
Thank you guys for your care and help.
Regards
ArmyAg08 said:
I only asked because I thought ROM manager was known to brick this tablet if you tried to install a recovery with it. I may be mistaken though.
Sent from my ASUS Transformer Pad TF700T
Click to expand...
Click to collapse
You're right. I wasn't mad/annoyed at your post. I just wanted to point out it has been known for a while now that ROM Manager does funky things on the 700. I'd just stay away from it -- iIn the sense that if one aspect of a program is broken by a device's particulars, changes are relatively high that some other aspect(s) is/are broken as well and you might get to know which one(s) that is/are by first-hand experience.
_that said:
APX is also NOT fastboot - in APX mode you can *only* use nvflash, but for that you'd need to have created the blob before bricking.
Click to expand...
Click to collapse
You're right. I was cutting the curve. I'm sorry for the confusion.
okantomi said:
shreef, the short answer is that only ASUS can help you now. I believe that is your only solution.
I'm so sorry.
Click to expand...
Click to collapse
That is quite the accurate summary.
@OP: hope ASUS treats your device nicely and you can get back in our midst with a 700 working well for you, soon.
To sum everything up:
1. My rom didn't work so I decided to find a new one :good:
2. I read and understand that it's much easier using fastboot
3. I was flashing the official rom when the antivirus requested a reboot
4. I forgot the flashing, and just clicked on reboot :silly: :crying:
The screen remains black when I try to boot it up :crying:
The only sign of life is when I'm charging the light is lighting and "APX" is showing in the device manager on pc with a yellow triangle, I haven't understand what "APX" stand for yet so please explain
(My bootloader was unlocked and I flashed twrp 2.5.5 just before I did this)
Do you have any tips for me? Or is the device bricked and have to be sent for service?
Please help me :fingers-crossed:
Edit: This is wrong section I know, can anyone move it to the Q&A please?
Moved.
mathiash98 said:
To sum everything up:
1. My rom didn't work so I decided to find a new one :good:
2. I read and understand that it's much easier using fastboot
3. I was flashing the official rom when the antivirus requested a reboot
4. I forgot the flashing, and just clicked on reboot :silly: :crying:
The screen remains black when I try to boot it up :crying:
The only sign of life is when I'm charging the light is lighting and "APX" is showing in the device manager on pc with a yellow triangle, I haven't understand what "APX" stand for yet so please explain
(My bootloader was unlocked and I flashed twrp 2.5.5 just before I did this)
Do you have any tips for me? Or is the device bricked and have to be sent for service?
Please help me :fingers-crossed:
Edit: This is wrong section I know, can anyone move it to the Q&A please?
Click to expand...
Click to collapse
Apx is a method provided by the cpu manufacture for recovery. Due to the way asus has handled locking the unit apx is only available if nvflash is installed while on ICS (4.0).
Reset may be a good option for you. Power on unit. Hold volume down and insert a small paperclip to into into the reset hole. This may get you into the bootloader.
Reset: A small hole about 25mm or 1inch below the sdcard slot.
Note: If this fails you could do the same but hold volume up and hope.
Beyond this running the battery down has worked for some or remove the back cover and disconnect the battery. Leave it disconnected for thirty minutes, then reconnect.
Also see my signature for other methods to get into the bootloader. Don't bother with apx as it is useless for us.
We are looking for any change in the unit. With a change may come use of adb, fastboot, or recovery.
Try do each thing in turn and repeat this sequence twice more.
Thanks for the explanation and fir the tips! I'm going to try this
mathiash98 said:
Thanks for the explanation and fir the tips! I'm going to try this
Click to expand...
Click to collapse
Good Luck!
tobdaryl said:
Good Luck!
Click to expand...
Click to collapse
It doesn't seem that any of the following work, but I haven't tried the battery pull thing, because I see that it's a sticker over the cover that says that the warrenty is void if removed. If I send it for service will the guys know that I have unlocked it, and then void the warranty?
mathiash98 said:
It doesn't seem that any of the following work, but I haven't tried the battery pull thing, because I see that it's a sticker over the cover that says that the warrenty is void if removed. If I send it for service will the guys know that I have unlocked it, and then void the warranty?
Click to expand...
Click to collapse
I understand. If still in warranty I wouldn't remove it either.
I'm sorry that is all I have for your situation.
Lads, let me join your conversation. I've almost same problem, probably different root cause, but same summary:
1. Originally I downloaded JB 4.2 from support.asus.com source
2. Tablet got reflashed & worked as normal, but I lost roots which I had earlier, therefore I decided to get root privs again.
3. So, I went into TWRP web-site & downloaded openrecovery-twrp-2.5.0.0-tf300tg-JB.blob blob file & via ADB was able to flash TWRP 2.5 onto my TF300T, but...
4. ...somehow TWRP doesn't let me to mount neither system, not SD-card, nothing. And currently
5. I think I'm bricked (& my TF300T too). When I press power button - tablet switches on & gets straight into TWRP, where I've only option to power it down or reboot TWRP tells me "are you sure? No OS installed".
6. When I try to switch tablet into bootload (with volume -) writing "The Device is Unlocked" shortly blinks slightly brighter, kind of trying to get into bootloader, but gets into TWRP anyway.
Any help, please! I know how Donate button works!
P.S. Because I very new writer (but really old reader) of XDA - I can't incert outside links...
goldenval said:
Lads, let me join your conversation. I've almost same problem, probably different root cause, but same summary:
1. Originally I downloaded JB 4.2 from support.asus.com source
2. Tablet got reflashed & worked as normal, but I lost roots which I had earlier, therefore I decided to get root privs again.
3. So, I went into TWRP web-site & downloaded openrecovery-twrp-2.5.0.0-tf300tg-JB.blob blob file & via ADB was able to flash TWRP 2.5 onto my TF300T, but...
4. ...somehow TWRP doesn't let me to mount neither system, not SD-card, nothing. And currently
5. I think I'm bricked (& my TF300T too). When I press power button - tablet switches on & gets straight into TWRP, where I've only option to power it down or reboot TWRP tells me "are you sure? No OS installed".
6. When I try to switch tablet into bootload (with volume -) writing "The Device is Unlocked" shortly blinks slightly brighter, kind of trying to get into bootloader, but gets into TWRP anyway.
Any help, please! I know how Donate button works!
P.S. Because I very new writer (but really old reader) of XDA - I can't incert outside links...
Click to expand...
Click to collapse
Which tablet do you have? You show TF300T but using TF300TG twrp.
The bootloader changed again with 4.2 firmware and requires twrp especially for that version. I have been told the openrecovery-twrp-2.5.0.0-tf300t-4.2.blob does not work properly so you should have used openrecovery-twrp-2.4.4.0-tf300t-4.2.blob if you have a tf300t.
We need to break the cycle of going into twrp and only twrp.
Let's try to use twrp for that purpose. While in twrp select reboot while holding volume down.
If that fails to make a change while in twrp type adb reboot bootloader.
If that makes no change type fastboot -i 0x0B05 reboot-bootloader.
If there is still no change try the reset while holding volume down.
Reset: A small hole about 25mm or 1inch below the sdcard slot. Use a small paperclip to insert into the hole and press gently while holding volume down.
Dear Friend! :good: That what makes difference between you - old member & me - amatuer. Yes, I loaded ...TG version of TWRP onto my ..T tablet. Bad words aren't allowed in XDA forum, otherwise I'd call myself with proper name. Anyway,
I tried to reboot from TWRP, held volume - & had no success. It loaded into TWRP again.
Then tried to reboot with command adb reboot bootloader, as you mentioned - my Windows7 PC doesn't see tablet, showing Transformer with yellow ! sign. And I tried fastboot -i 0x0B05 reboot-bootloader command, ADB is saying <waiting for device> forever & nothing happens. so I stopped here so far, waiting for your advise...
We need to break the cycle of going into twrp and only twrp.
Let's try to use twrp for that purpose. While in twrp select reboot while holding volume down.
If that fails to make a change while in twrp type adb reboot bootloader.
If that makes no change type fastboot -i 0x0B05 reboot-bootloader.
If there is still no change try the reset while holding volume down.
Reset: A small hole about 25mm or 1inch below the sdcard slot. Use a small paperclip to insert into the hole and press gently while holding volume down.
No bad words needed. We all make mistakes. I them pointed out for future reference in case you were not aware.
First you need to get your drivers loaded for windows.
[GUIDE] How to install Universal Naked Drivers
Use that guide to get your drivers properly installed and retry the adb and fastboot commands.
goldenval said:
Dear Friend! :good: That what makes difference between you - old member & me - amatuer. Yes, I loaded ...TG version of TWRP onto my ..T tablet. Bad words aren't allowed in XDA forum, otherwise I'd call myself with proper name. Anyway,
I tried to reboot from TWRP, held volume - & had no success. It loaded into TWRP again.
Then tried to reboot with command adb reboot bootloader, as you mentioned - my Windows7 PC doesn't see tablet, showing Transformer with yellow ! sign. And I tried fastboot -i 0x0B05 reboot-bootloader command, ADB is saying <waiting for device> forever & nothing happens. so I stopped here so far, waiting for your advise...
We need to break the cycle of going into twrp and only twrp.
Let's try to use twrp for that purpose. While in twrp select reboot while holding volume down.
If that fails to make a change while in twrp type adb reboot bootloader.
If that makes no change type fastboot -i 0x0B05 reboot-bootloader.
If there is still no change try the reset while holding volume down.
Reset: A small hole about 25mm or 1inch below the sdcard slot. Use a small paperclip to insert into the hole and press gently while holding volume down.
Click to expand...
Click to collapse
Ok...
So, I bricked my tf300t. I ordered a new motherboard off ebay and replaced the bricked one. It works, but it was not factory reset and still has the owners info, etc. It is password protected. I don't know the pw. When I try to boot into the recovery console, I get a dead android. Going into the menu, I have an option to wipe or boot android. How do I get around this?
n3tm0nk said:
So, I bricked my tf300t. I ordered a new motherboard off ebay and replaced the bricked one. It works, but it was not factory reset and still has the owners info, etc. It is password protected. I don't know the pw. When I try to boot into the recovery console, I get a dead android. Going into the menu, I have an option to wipe or boot android. How do I get around this?
Click to expand...
Click to collapse
My suggestion is use stock recovery to replace the encrypted os (probably JB 4.2) with JB 4.1 (10.4.2.20). You can download here [INDEX]25 Apr 2013 - TF300T/TG WITH ALL ASUS ORIGINAL TOOLS-Firmwares-Kernels-Guides-. Look in firmware TF300T. Use the proper sku (ww, us, etc) for your country. Please give philos64 a thanks while there he spent much time creating that post, supporting the downloads, and updating.
Unzip the downloaded file once - rename to EP201_768_SDUPDATE.zip. Place the file on your internal sdcard if possible if not place on your micro sdcard. Boot into the recovery console and make the hungry android happy. This will probably take ten plus minutes.
Dear tobdaryl! Thanks very much for your advice, I had to dissapear for couple of days, so couldn't answer. I followed your link & had no success. When I power on TF300T & connect it to PC, it's being read as Transformer (see my 1st picture), unlike in the guide they are working with Asus Eee pad device (my 2nd picture), so when I'm trying to install drivers from un-zipped folder it says "...couldn't install drivers for your Transformer".
Looking for more help... (
tobdaryl said:
No bad words needed. We all make mistakes. I them pointed out for future reference in case you were not aware.
First you need to get your drivers loaded for windows.
[GUIDE] How to install Universal Naked Drivers
Use that guide to get your drivers properly installed and retry the adb and fastboot commands.
Click to expand...
Click to collapse
goldenval said:
Dear tobdaryl! Thanks very much for your advice, I had to dissapear for couple of days, so couldn't answer. I followed your link & had no success. When I power on TF300T & connect it to PC, it's being read as Transformer (see my 1st picture), unlike in the guide they are working with Asus Eee pad device (my 2nd picture), so when I'm trying to install drivers from un-zipped folder it says "...couldn't install drivers for your Transformer".
Looking for more help... (
Click to expand...
Click to collapse
Right click on the Transformer with the yellow symbol and point to your Universal Naked Drivers inf file. If one inf files fails to install then try the other.
tobdaryl said:
Right click on the Transformer with the yellow symbol and point to your Universal Naked Drivers inf file. If one inf files fails to install then try the other.
Click to expand...
Click to collapse
Tobdaryl, I couldn't find "Donate Me" button in your profile, so give me your paypal account for a little present please! :good: It worked!!! I installed correct driver from given guide, rebooted into bootloader, using ADB comand & got 3 icons: RCK, Android & Wipe Data. I tried Wipe Data, it said "can't mount something", don't remember now what. I rebooted again & clicked on Android & loaded into normal screen. Because of Asus became completely flat I put it on charge now. And after that I will have to come back to original task - to root my TF300T. While it's charging I downloaded Goo manager & tried to install TWRP, it said "No recoveries were found for your device", but in same time file for my device (that's where I made mistake, downloading TF300TG version) does exist, so what's story here? I guess this is may be because my TF300T isn't rooted yet?
Adding later. after digging this & other forums I found that in order to get root & have to have CWM/TWRP on my device & I can't get them until my TF300T is rooted. Am I confused & talking rubbish?
Adding 2 hours later. I rooted the device using XDA guide. Still trouble to reboot device. It always reboots into TWRP, then I have to connect it to PC & reboot with ADB commands. This isn't right...
goldenval said:
Tobdaryl, I couldn't find "Donate Me" button in your profile, so give me your paypal account for a little present please! :good: It worked!!! I installed correct driver from given guide, rebooted into bootloader, using ADB comand & got 3 icons: RCK, Android & Wipe Data. I tried Wipe Data, it said "can't mount something", don't remember now what. I rebooted again & clicked on Android & loaded into normal screen. Because of Asus became completely flat I put it on charge now. And after that I will have to come back to original task - to root my TF300T. While it's charging I downloaded Goo manager & tried to install TWRP, it said "No recoveries were found for your device", but in same time file for my device (that's where I made mistake, downloading TF300TG version) does exist, so what's story here? I guess this is may be because my TF300T isn't rooted yet?
Adding later. after digging this & other forums I found that in order to get root & have to have CWM/TWRP on my device & I can't get them until my TF300T is rooted. Am I confused & talking rubbish?
Adding 2 hours later. I rooted the device using XDA guide. Still trouble to reboot device. It always reboots into TWRP, then I have to connect it to PC & reboot with ADB commands. This isn't right...
Click to expand...
Click to collapse
Go manager does not have the proper twrp for our tablet.
Rooting is no longer required to flash twrp. Motochopper will root with just adb.
I suggest we try to get everything working properly with stock before changing or adding anything.
Go to to this link and download the stock Asus firmware 10.4.2.20. Choose the proper sku for your location (ww, us or whatever). Don't forget to thank philos64 while there. Unzip once and place on your tablet, flash with twrp, if that fails unzip again and place the blob file in the directory with adb and fastboot and flash with fastboot. Verify everything works properly before making any other changes.
Thank you for the donation offer.
I don't have a method to receive donations. A simple click on thanks will be good.
My problem is that because I installed wrong TWRP by mistake - it can't mount anything & I can't install anything from SD or internal memory. So, should I delete existing TWRP somehow &/or replace it by CWM recovery?
tobdaryl said:
Unzip once and place on your tablet, flash with twrp, if that fails unzip again and place the blob file in the directory with adb and fastboot and flash with fastboot
Click to expand...
Click to collapse
goldenval said:
My problem is that because I installed wrong TWRP by mistake - it can't mount anything & I can't install anything from SD or internal memory. So, should I delete existing TWRP somehow &/or replace it by CWM recovery?
Click to expand...
Click to collapse
No don't delete twrp or install cwm. We should have access to adb and or fastboot. We should be able to use either to get sorted.
Go to to this link and download the stock Asus firmware 10.4.2.20. Choose the proper sku for your location (ww, us or whatever). Don't forget to thank philos64 while there. Unzip twice and place the blob file in the directory with adb and fastboot and flash with adb. Verify everything works properly before making any other changes.
adb push blob /sdcard/blob
adb shell
su
dd if=/sdcard/blob of=/dev/block/mmcblk0p4
exit
adb reboot
May I ask you then? My ROM number is: JOP40D.WW_epad-10.6.1.15.3-20130416 & as I can see from numbers you are offerring me to downgrade (from 4.2 to 4.1). Will this not kill the device? And why can't we re-install existing ROM through ADB? I'm not arguing, just trying to understand.
tobdaryl said:
No don't delete twrp or install cwm. We should have access to adb and or fastboot. We should be able to use either to get sorted.
Go to to this link and download the stock Asus firmware 10.4.2.20. Choose the proper sku for your location (ww, us or whatever). Don't forget to thank philos64 while there. Unzip twice and place the blob file in the directory with adb and fastboot and flash with adb. Verify everything works properly before making any other changes.
adb push blob /sdcard/blob
adb shell
su
dd if=/sdcard/blob of=/dev/block/mmcblk0p4
exit
adb reboot
Click to expand...
Click to collapse
Hi!
Unfortunately there is no topic for Asus Tf303CL, but since it is the member of the TF3xx family I hope this post can stay here.
The problem is, that I'm stuck at the Asus boot (static white) logo and can't go further in booting.
I've tried ADB, but there's no response on the "adb devices" command.
I've also tried fastboot, but only two commands are woriking:
"fastboot devices" comes back with an alphanumeric number and
"fastboot continue" turns off the tablet.
The other fastboot commands are returning with the message "fastboot failed <remote failure>"
So finally I've found some hints that maybe with xFSTK I would able to fix fastboot, then with the Asus Flast Tool I supposed to be able to flash the stock raw rom (which I've already done before).
But unfortunately xFSTK is ether not working (no communication) or I'm using it wrong. As far as I know TF303CL has Intel SoC with Baytrail platform, so I used the Baytrail B0 tab in xFSTK and I've loaded the *ifwi*.bin file which I found in the stock raw rom.
Is this the right way to fix fastboot or I have to do something else? Or the tablet may has hardware defect?
mucden1 said:
Hi!
Unfortunately there is no topic for Asus Tf303CL, but since it is the member of the TF3xx family I hope this post can stay here.
Click to expand...
Click to collapse
I think it was a good idea to open this thread. To my mind your device is really very close related to TF300T and TF700T. The OS is Android 4.4. So it might be worth to attempt to flash a CR like "KatKiss - Nougatella"
But before you may start is to clarify following:
1. Is the bootloader on your device unlocked?
2. Is there already any custom recovery like TWRP on your device?
3. Can you boot into fastboot protocol by holding Power on and Volume down together?
If you cannot get access neither through ADB or Fastboot, your device is bricked for good. Sorry!
1. Is the bootloader on your device unlocked?
I have no idea. It bought it brand new, but I already had to debrick it once with Asus Flash Tool about a year ago. So raw firmware was flashed. I don't know whether flashing a raw rom with AFT requires unlocked bootloader or not.
2. Is there already any custom recovery like TWRP on your device?
As far as I know it has stock recovery.
3. Can you boot into fastboot protocol by holding Power on and Volume down together?
I think Power on & Vol down is the key combination for recovery mode. Power on & Vol up is the combination for fastboot. I can't access to recovery, but fastboot may partially work.
If you cannot get access neither through ADB or Fastboot, your device is bricked for good. Sorry!
Whit adb
Code:
adb devices
command has no response. With fastboot I have a response on the
Code:
fastboot devices
command, it returns some kind of an id. Beside this
Code:
fastboot continue
makes the device to turn off. Other fastboot commands (as I wrote) are returning with the "fastboot failed <remote failure>" response.
These are what I have tried so far:
reboot, reboot bootloader, update, flash (several images), erase cache, erase data
mucden1 said:
1. Is the bootloader on your device unlocked?
I have no idea. It bought it brand new, but I already had to debrick it once with Asus Flash Tool about a year ago. So raw firmware was flashed. I don't know whether flashing a raw rom with AFT requires unlocked bootloader or not.
Click to expand...
Click to collapse
People usually unlock their bootloader to root their device or install Custom ROM on it. I think your bootloader is still locked. On the other side in the left above corner of the dark screen should appear the hint "the device is unlocked" during the boot process.
For the TF300xx family there is an Asus unlock tool V8 available. I don't know if it is useable for your device. Please call Asus support and ask them about that. On the other hand there is a tutorial here: https://qitapso.com/how-to-unlock-asus-transformer-pad-tf303cl-bootloader/
Should I try to unlock the bootloader?
mucden1 said:
Should I try to unlock the bootloader?
Click to expand...
Click to collapse
Of course!
But it's on your own risk. You have to make the decision yourself.
ebonit said:
Of course!
But it's on your own risk. You have to make the decision yourself.
Click to expand...
Click to collapse
The link above goes to "AutorootTools" which is not a real sw, only promising download after an unwanted and long survey. I consider it as a dangerous site.