Database Info

Need help un-bricking my soft-bricked GS3

First off, I have a Verizon GS3 (SCH-I535). As of this morning, it was running the new 4.3 standard (no root, no unlocked bootloader, no custom recovery). I didn't like some of the UI changes in 4.3, and since I wanted to try custom ROMs out anyways, I figured now would be as good a time as any.
After doing hours of research, I was able to successfully get my phone rooted and TWRP installed (using the GooManager app). I had the AOKP d2vzw rom (milestone 1) downloaded and on my phone. I then tried to use GooManager to install the ROM. The phone rebooted into download mode, then gave an error message. I think I didn't properly unlock the bootloader.
After that, the phone wouldn't boot to a ROM at all. I've been trying to install stock ROMs using ODIN and was able to get the stock recovery back, but now all I can get to is the stock recovery and the Download Mode. Whenever the phone boots normally, I get the message, "System software not authorized by Verizon Wireless has been found on your phone . . ."
The biggest issue I've had is that it seem like nothing will install properly using ODIN. When trying to flash TWRP, it fails after NAND Write Start!!. When trying to flash a bootloader, it'll give a write/fail after aboot.
At this point, I'll be happy just getting it back to a working ROM. Any help would be appreciated.

WhiteRabbit44 said:
First off, I have a Verizon GS3 (SCH-I535). As of this morning, it was running the new 4.3 standard (no root, no unlocked bootloader, no custom recovery). I didn't like some of the UI changes in 4.3, and since I wanted to try custom ROMs out anyways, I figured now would be as good a time as any.
After doing hours of research, I was able to successfully get my phone rooted and TWRP installed (using the GooManager app). I had the AOKP d2vzw rom (milestone 1) downloaded and on my phone. I then tried to use GooManager to install the ROM. The phone rebooted into download mode, then gave an error message. I think I didn't properly unlock the bootloader.
After that, the phone wouldn't boot to a ROM at all. I've been trying to install stock ROMs using ODIN and was able to get the stock recovery back, but now all I can get to is the stock recovery and the Download Mode. Whenever the phone boots normally, I get the message, "System software not authorized by Verizon Wireless has been found on your phone . . ."
The biggest issue I've had is that it seem like nothing will install properly using ODIN. When trying to flash TWRP, it fails after NAND Write Start!!. When trying to flash a bootloader, it'll give a write/fail after aboot.
At this point, I'll be happy just getting it back to a working ROM. Any help would be appreciated.
Click to expand...
Click to collapse
When you are on 4.3, you can't unlock your phone anymore. That means no AOSP roms, but you can still use custom touchwiz roms based on 4.3. You're softbricked and you have to use this thread to fix it.
http://forum.xda-developers.com/showthread.php?t=2586319
After that completes, you can use this to root.
http://forum.xda-developers.com/showthread.php?t=2565758
Once you're rooted, this is the only recovery you can install, don't flash any other recovery.
http://forum.xda-developers.com/showthread.php?t=2605648
Read up on all the threads, 4.3 is completely different then 4.1 was.
Sent from my SCH-I535 using Tapatalk 2

Extra Info:
With Odin, I have made sure Kies is uninstalled. I've also tried multiple USB cables, including the ones the phone came with, and I've tried almost every USB port on my computer. Whenever Odin fails, it's in the exact same spot every time, which makes me think it's a software issue, not a hardware issue.
EDIT:
I was actually able to get the stock.vzw-root66 ROM installed by Odin without any errors. The phone rebooted immediately, then showed the android robot with the blue spinny thing in his chest, then the phone went back to the same Verizon error message.

BadUsername said:
When you are on 4.3, you can't unlock your phone anymore. That means no AOSP roms, but you can still use custom touchwiz roms based on 4.3. You're softbricked and you have to use this thread to fix it.
http://forum.xda-developers.com/showthread.php?t=2586319
After that completes, you can use this to root.
http://forum.xda-developers.com/showthread.php?t=2565758
Once you're rooted, this is the only recovery you can install, don't flash any other recovery.
http://forum.xda-developers.com/showthread.php?t=2605648
Read up on all the threads, 4.3 is completely different then 4.1 was.
Sent from my SCH-I535 using Tapatalk 2
Click to expand...
Click to collapse
This worked like a charm! Thank you. I admit I am fairly new at all of this and did a ton of research beforehand, but I apparently did not research the differences between 4.1 and 4.3. You saved my butt!

WhiteRabbit44 said:
This worked like a charm! Thank you. I admit I am fairly new at all of this and did a ton of research beforehand, but I apparently did not research the differences between 4.1 and 4.3. You saved my butt!
Click to expand...
Click to collapse
TW 4.3 discussion thread has most info consolidated in one place:
http://forum.xda-developers.com/showthread.php?t=2575661
Sent from my SCH-I535 using Tapatalk 4

[Q] New Note Pro?

Hey guys, I just got my Note Pro a week ago and just started looking into rooting. I keep getting a notification about a 128mb stability update. I would assume it's gonna update to the latest build but I'm not sure what the latest build is or if it'll be rootable afterwords. my current build is KOT49H.P900UEU1ANAE. What is the latest build #? Is there a list of updates somewhere detailing what the improvements are? I just want to root, debloat, turn off OTA and remove KNOX.
Edit: sorry forgot to mention it's just the wife model SM-P900

So 48 views and not one person can tell me the latest build# ? I'll figure out the rest.
Sent from my SM-N900V using Tapatalk

Have you checked SamMobile?
http://www.sammobile.com/firmwares/database/SM-P900/XAR/
How i got there:
http://www.sammobile.com
1. Click Firmware on the top.
2. Click the greyed out firmware database link under the blue banner.
3. Under "Select your firmware" I picked Tablet-->Android-->SM-P900....-->Cellular South (which matches the US variants)

muzzy996 said:
Have you checked SamMobile?
http://www.sammobile.com/firmwares/database/SM-P900/XAR/
How i got there:
http://www.sammobile.com
1. Click Firmware on the top.
2. Click the greyed out firmware database link under the blue banner.
3. Under "Select your firmware" I picked Tablet-->Android-->SM-P900....-->Cellular South (which matches the US variants)
Click to expand...
Click to collapse
Thanks muzzy! I had already been to SamMobile but all it had was foreign countries listed. I didn't know about Cellular South being the US version. I'll look again.
Edit: oh look a list of the updates and release dates! My Wi - fi reception seems slow, do any of the update fix that?

I honestly can't say. I'm on NC5 which is dated back in April and have no major issues.
I'm rooted and debloated though, not that this would impact the wifi performance . .

48 views doesn't mean 48 users. About 44 of those are Google Content Crawler, which is Google search engine's bots crawling the net for content to display in google.com. It is an automated process.
Samsung doesn't release changelists, so we don't know what each update does beyond what we can see.

Thanks for the help guys! I just accepted the first update and it took me to ANC5. I guess I'll have to accept all updates until current and then try CF-Auto-Root. I'll report back then.

Actually I just got my tablet like a week ago as well. I m on the same build no as well....haven't updated yet. I also haven't installed Knox either. There is a download arrow on the Knox icon and if I click the icon it starts downloading so I just cancel it. I am thinking of rooting as well. Well what I m trying to say is...keep the thread updated and I will just follow your lead.....hehe.

It always helps to know your country as well as different countries are on slightly different versions. You can always go to sanmobile.com, click on firmware and search for p-900. That will give you the list of all the latest ROMs for different countries / carriers. US based ROMs are listed as "Cellular South".

Successful Root!
Okay guys sorry it's taken so long to respond, I had hernia surgery on Monday so I've been behind on getting this rooted.
My plan was to use CF-Auto-Root and then load TWRP recovery and then load "Debloat Stock Variant" by Gatsrom. I decided to do it in that order because I wasn't sure I could load a custom recovery without being rooted first.
I accepted all updates up to the current = P900UEU1BNK1. Using Win 7 and loaded Samsung drivers. Downloaded ODIN 3.09, Odin 3.07 came with CF-Auto-Root and downloaded TWRP. Booted into download mode and made sure ODIN recognized my P900. And this is when to fun began! Everything seem to be going okay but I did run into a snag. I used ODIN 3.07 because that's what came with Auto- Root and I'd read somewhere of people having trouble with 3.09??? Anyways I got a red "FAIL" message and my screen displayed multicolored lines. I tried running it in ODIN 3.09 and got the same result. (i didn't disconnect anything between the 3.07 or 3.09 attempts, maybe i should have?). I disconnected my P900 and it rebooted giving me a Firmware Error screen telling me to use Kies "Recovery Mode". I tried Kies Recovery but Kies3 wouldn't even recognize the P900. (I started freaking a little at this point!) Anyways, I decided to try and load TWRP because I thought I've got nothing to lose! I loaded TWRP into ODIN and it took, so I thought, because my P900 rebooted into an up and running normal state. (Big Sigh!) I tried booting into recovery but TWRP didn't take, it came up to stock recovery, trying to load TWRP just kicked the P900 out of the Firmware Error state it was in?? I decided to give Auto-Root another go after rebooting Win 7. Used ODIN 3.09 this time and everything went fine and I was rooted! Then I loaded TWRP and it loaded fine! I performed a TWRP backup at this point and things seem to be running smoothly. I still need to load the Debloat Variant, that's what's on my plate for today.
http://forum.xda-developers.com/showthread.php?t=2656551
http://forum.xda-developers.com/showthread.php?t=2706982
http://forum.xda-developers.com/gal...t/rom-original-stock-debloated-stock-t2860069

You are a much braver sole than I. Hope all goes smoothly.

I could be wrong but I would think that if one is going to a different ROM then rooting isn't necessary. Simply use Odin to flash TWRP but ensure that auto reboot is not enabled in Odin when you do it. If you allow the device to begin booting into stock system it's going to overwrite recovery again (with stock recovery) so what you want to do is flash TWRP, and once it's flashed FORCE a reboot directly into recovery again using the hardware keys on the device. At that point you can do an nandroid backup and then flash your ROM.
Sent from my SM-P900 using Tapatalk

treetopsranch said:
You are a much braver sole than I. Hope all goes smoothly.
Click to expand...
Click to collapse
I'm not that brave treetop! I just know my way around a computer and I've rooted a few of these things. Plus I know the guys here on XDA are good at helping out if you hit a snag. Luckily I figured this one out on my own! You've just gotta do your research before jumping in and search read, search read, search read! I provided some links to get you started....get to it!
muzzy99 said:
I could be wrong but I would think that if one is going to a different ROM then rooting isn't necessary. Simply use Odin to flash TWRP but ensure that auto reboot is not enabled in Odin when you do it. If you allow the device to begin booting into stock system it's going to overwrite recovery again (with stock recovery) so what you want to do is flash TWRP, and once it's flashed FORCE a reboot directly into recovery again using the hardware keys on the device. At that point you can do an nandroid backup and then flash your ROM.
Sent from my SM-P900 using Tapatalk
Click to expand...
Click to collapse
Thanks for the info muzzy, I'll remember that for next time! :good:
I did get the Debloat Variant up and running and loaded Xposed framework with sdcard full access. Everything seems to be running smoothly!

Ok So I finally got to it and successfully rooted (in first try, if I may add ). Thanks to xblue's guide/heroic efforts I avoided certain things and everything went smoothly. So Basically I installed samsung drivers using Kies, rebooted pc (Win 8.1). Downloaded cf autoroot and downloaded odin 3.09 as autoroot comes with 3.07. Replaced ONLY 3.07 odin exe with 3.09. Started Odin in Admin mode, put the tablet in download mode. Attched to pc and Odin recognized it. Then Gave it a final thought......lol. Pressed Start, device booted couple times. Then PASS appeared on the Odin window after like 30 secs. Installed root checker...successfully rooted. Installed TWRP via odin and flashed that successfully. Made a full back up and installed a ROM of my choice. I am a happy camper.

Sweet Deal singhsta! I'm glad my efforts were a help!

i would update to the latest version.. i tried using the original one that you have however i got the screen flicker issue so had to update.. the first update isnt very good wifi keeps dropping but the most recent version doesn't tho you may have a bug where every time you unlock the screen the tablet is still asleep even though the icons are visible so you have to lock the screen again and unlock. however if you factory reset this bug goes away.
i find the latest version is the most stable and battery life is better if you disable all the unnecessary apps that you can i usually get rid of most of the samsung back up apps and all the google ones bar the ones it needs to run play store etc and maintaining the ones that sync for back up.
wifi was really slow when i first got it and would drop very annoying but now it seems better but have experienced slow wifi i think it's a hardware issue all note pro's have in built that should have been sorted by the latest build. i hope they finally give it an update in the coming months even to 4.4.4. or something.

Nothing will flash anymore...

It's been a long night and I'm at a complete loss as to what to look for next...
Around 9PM last night, my phone randomly rebooted... it's done this a few times before, and i thought nothing of it. When it finally booted back up, I was at the "choose your language" setup screen. WTF.
I lost literally EVERYTHING.
FYI, this was on stock rom, and I didn't even have the OTA(s) because I was rooted and was content with 4.4.2
Well, since all my data was gone, I figured it was about time to see what I could get with a custom ROM. The phone's been sluggish lately, so I figured a bloat-less upgrade would help.
Long story short, I loaded the 5.1 firmwares for VZW, and the HBOOT as well, and flashed GPE_5.1 on it. It took it like a champ, but refused to boot. I tried changing the kernels during the GPE install, but none of them worked. Some would loop, some would kick me into recovery, and one would just stall and the animation would run forever. No worries, I'm sure I can go to a stock 5.x rom! But that's a big NOPE. I just get "installation aborted" with no reasoning or errors in CWM (I had TWRP at one point as well, and it didn't get me anywhere either) Or I get "symlink: some symlinks failed" ... it depends what rom i'm flashing.
I've tried stock and custom, rooted and not... literally nothing will take.
ALSO, in my attempts to remedy the problem, I tried to reflash the firmware, but fastboot starts that there's not enough space. A quick google search pointed to "not enough ram in the PC" which is BS because it's done it on 2 different systems, both with 16GB ram, one running Win8.1 and the other Win7.
To top it all off, somehow I relocked the phone (but i still have S-OFF) and without being able to boot into the OS, I can't unlock it with SunShine/Firewater.
Hopefully, someone can point me in the right direction...

Welp... It's working now...
Not 100% sure what I ended up doing that worked, but I was able to run the unlocker via creating a new unlock_code.bin from htcdev and ran that with the all in one toolkit.
From there, I was able to use the toolkit to flash a stock ruu rom (I flashed the 5.0.1 RUU, but when it booted, I was still in 4.4.2)
It apparently didn't like somwething in the boot order other than the ROM itself.
I'm now running S-OFF, relocked but rooted 5.0.1 after it took several OTAs. Not sure how many more OTA's are pending, but it just keeps prompting me lol...
At this point, I'm just happy it's booting, stock or not. I don't even know what recovery I'm running at this point...

Did you update your recovery??? To the latest one
Sent from my HTC6525LVW using XDA Premium 4 mobile app

Bricked? This shouldn't be happening.

Here's a basic rundown of what happened. I completely rooted my Galaxy S III i535 on 4.4.2, and i installed SafeStrap (A Version of TWRP) since the Verizon S3 has a locked bootloader.
So here's what I tried to do. Using SafeStrap, I backed up my stock rom. And i selected another ROM slot. Using this, i tried experimenting by installing a ROM for another Carrier (They say not to do this, but i have in the past with success, so i thought it mightve worked)
(KEEP IN MIND, THE STOCK OS WAS STILL INSTALLED AND I EVEN HAD A BACKUP)
So, it didnt work and stopped halfway. I rebooted the phone, and Hard bricked.
Doesnt boot up, does not turn on, will not boot recovery or download, or any sign of some boot at all.
And, i get the qhsusb_dload sign on my pc.
Can anyone point me in the right direction, or at least tell me the cause of this problem? Thanks.

CrimsonKatsuro said:
Here's a basic rundown of what happened. I completely rooted my Galaxy S III i535 on 4.4.2, and i installed SafeStrap (A Version of TWRP) since the Verizon S3 has a locked bootloader.
So here's what I tried to do. Using SafeStrap, I backed up my stock rom. And i selected another ROM slot. Using this, i tried experimenting by installing a ROM for another Carrier (They say not to do this, but i have in the past with success, so i thought it mightve worked)
(KEEP IN MIND, THE STOCK OS WAS STILL INSTALLED AND I EVEN HAD A BACKUP)
So, it didnt work and stopped halfway. I rebooted the phone, and Hard bricked.
Doesnt boot up, does not turn on, will not boot recovery or download, or any sign of some boot at all.
And, i get the qhsusb_dload sign on my pc.
Can anyone point me in the right direction, or at least tell me the cause of this problem? Thanks.
Click to expand...
Click to collapse
The solution may be a debrick image. They are designed to boot the phone from an external sdcard and from there reinstall the stock rom/firmware. I haven't searched yet, but check the general and development threads, possibly the stickied summary thread.
Check this thread

Root on PD2 6.0.1 Sprint S6 Edge/TWRP 3.0.2-1.

Hi folks,
just posting this writeup thinking maybe it might be of help to some people.
Started with a clean S6 Edge straight from Samsung repair for broken screen. Factory wipe, KNOX reset. It had the PD2 update. Tried using Skipsoft's Toolkit and ponied up a donation to get the Pro version with the S6 Edge 6.0.1 update, but it didn't work: it got stuck at the "SEANDROID NOT ENFORCING" screen after flashing TWRP 3.0.2. I know there are issues with 3.0.2, but it's what's optioned in Toolkit now.
Flashing TWRP 2.8.7.0 results in normal boot, but I could not enter recovery mode for some reason. 3.0.0-0 didn't work, either.
What I ended up doing is forcing phone into download mode (Power+Volume Down+Home), ODINing TWRP 3.0.2-1. This resulted in a bootloop (somewhat expected). But I could get into recovery easily. From recovery, I flashed Renegade's PD2-Aroma V3.0 Full ROM via ADB sideload. After a very long first boot, everything works 100%! Root, SuperSU, etc., all taken care of. Hotspot works.
Notes and tips:
- While I didn't use Skipsoft's Toolkit in the end, it's still worth supporting. Might work smoothly using 3.0.2-1 instead of 3.0.2.0, but I'm comfortable with adb/fastboot/etc. so just ended up using that. If you don't already have Android SDK and tools/platform-tools, Skipsoft conveniently includes those commands in its directory under C:\Unified_Android_Toolkit (they're named adb-toolkit and fastboot-toolkit. You can copy and rename them as "adb" and "fastboot" for convenience).
- Make sure you get the right TWRP 3.0.2-1 device version. You want to use twrp-3.0.2-1-zeroltespr.tar.md5 for Sprint S6 Edge. Remove the .md5 part and set it to use the .tar extension (stupid Windows asks you to confirm file extension type change).
- In TWRP you can either push your custom ROM or sideload it. To push a file, move the custom ROM into the same directory you've got adb/fastboot for convenience. Open a terminal window in that directory, and either "adb push customromfilenamehere.zip /sdcard/" or in TWRP, click Advanced/ADB Sideload, and enter "adb sideload customromfilenamehere.zip".
- If you're sideloading it, it's gonna take a while, and will start flashing even while the transfer percentage is creeping up. Example: at around 9%, it started AROMA, around 14%, it went through some of the installation options. It was done flashing everything and ready for reboot even though the terminal window said only 76% was transferred. That's ok. Click "finish" in AROMA on phone, reboot. Unplug phone. Wait a long time for first boot (this took around 20 minutes for me). ENJOY.
Remember: all is not lost as long as you can get into download mode! Power-Volume Down-Home until you get to screen prompting to get to download mode. Volume up to select that mode. You can ODIN from here.
Additionally: if you find yourself for whatever reason stuck at the initial S6 Edge boot screen with "SEANDROID NOT ENFORCING," you might be in some kinda of boot limbo. I was able to issue some adb commands here, even with recovery was borked and the phone didn't boot all the way. Doing an "adb reboot-bootloader" would let me do a complete boot to ROM while I was trying to get the different TWRP versions working (until 3.0.2-1).
Hope this helps someone.
tl;dr: For PD2/6.0.1 Sprint S6 Edge, manual flash TWRP 3.0.2-1. Push custom ROM through Recovery. Reboot, wait a long time. Success!

Just to Clarify (and mostly for myself), I think this is the simplest and most foolproof way to get yourself fully update and on a custom rom with root.
1. ODIN Stock PD2 Image. Reboot, make sure dev options + USB debugging is enabled.
2. ODIN latest TWRP 3.0.2.1 - HERE.
3. Obtain root by going into TWRP immediately after you install it and flashing the root kernel Ram did for this device - HERE
4. Then after wiping cache, dalvik and data in TWRP, flash Renegade ROM 3.0 PD2.
Using CFauto root method is known to cause issues. This is the type of approach I took and it was flawless. The initial boot of the Renegade ROM can seriously take like 20min though, I thought I was looping for a second.
If anyone disagrees with this method or sees where it can be done better, please advise. This seems to prevent the instance of any loops or issues. The Renegade ROM has a rooted kernel so flashing the root kernel is likely a redundant step. You could omit Step 3 if you are flashing a custom ROM, probably, but it seems to prevent any hangups. But if you plan to stay stock, you still have to flash a rooted kernel after TWRP.

Alpine- said:
Just to Clarify (and mostly for myself), I think this is the simplest and most foolproof way to get yourself fully update and on a custom rom with root.
1. ODIN Stock PD2 Image. Reboot, make sure dev options + USB debugging is enabled.
2. ODIN Ram's TWRP 3.0.2 - HERE I'm assuming the other guy's 3.0.2 works fine too, I am not sure why you hung and had to revert to a 2.x TWRP build.
3. Obtain root by going into TWRP immediately after you install it and flashing the root kernel Ram did for this device - HERE
4. Then after wiping cache, dalvik and data in TWRP, flash Renegade ROM 3.0 PD2.
Using CFauto root method is known to cause issues. This is the type of approach I took and it was flawless. The initial boot of the Renegade ROM can seriously take like 20min though, I thought I was looping for a second.
If anyone disagrees with this method or sees where it can be done better, please advise. This seems to prevent the instance of any loops or issues. The Renegade ROM has a rooted kernel so flashing the root kernel is likely a redundant step. You could omit Step 3 if you are flashing a custom ROM, probably, but it seems to prevent any hangups. But if you plan to stay stock, you still have to flash a rooted kernel after TWRP.
Click to expand...
Click to collapse
I noticed chainfire now has a CF-autoroot for the 925P 6.01 and people were having success using the one for the 925F. Any verification on this? Haven't seen anyone on this forum say anything about it. I just bought a new S6 edge for sprint. I always am about year behind on phones because of the high cost of the latest and greatest. I picked the edge because my wife has had one a year and it gets a lot better reception than my N5. But, I gots to have root and don't wanna screw up a new phone. I know the first thing I need to do is check which software it's running. Should I do this before I activate it or can i stop any system upgrades before they install?

baknblack said:
I noticed chainfire now has a CF-autoroot for the 925P 6.01 and people were having success using the one for the 925F. Any verification on this? Haven't seen anyone on this forum say anything about it. I just bought a new S6 edge for sprint. I always am about year behind on phones because of the high cost of the latest and greatest. I picked the edge because my wife has had one a year and it gets a lot better reception than my N5. But, I gots to have root and don't wanna screw up a new phone. I know the first thing I need to do is check which software it's running. Should I do this before I activate it or can i stop any system upgrades before they install?
Click to expand...
Click to collapse
I have not attempted to use CF-autoroot just because of reported issues and the general recommendation being to use the standard method. It may work fine now that its been updated, but I have not personally tested it.

Alpine- said:
I have not attempted to use CF-autoroot just because of reported issues and the general recommendation being to use the standard method. It may work fine now that its been updated, but I have not personally tested it.
Click to expand...
Click to collapse
I just bought my phone new off ebay it updated to PF4 just as soon as I activated it. I couldn't stop it. Anyway I used the CF autoroot on it and it worked perfectly. I tried to do it manually a couple times first and never could get TWRP to flash. It would say it was successful but, stock recovery stayed. Anyways, I got er done and running Renegade wich btw is an awesome ROM. This is my first samsung device and had I done a bit more research I'd of known the majority of development is on the regular S6. I just picked the edge because my wife has one and it worked so much better in the boonies than my N5 did.

baknblack said:
I just bought my phone new off ebay it updated to PF4 just as soon as I activated it. I couldn't stop it. Anyway I used the CF autoroot on it and it worked perfectly. I tried to do it manually a couple times first and never could get TWRP to flash. It would say it was successful but, stock recovery stayed. Anyways, I got er done and running Renegade wich btw is an awesome ROM. This is my first samsung device and had I done a bit more research I'd of known the majority of development is on the regular S6. I just picked the edge because my wife has one and it worked so much better in the boonies than my N5 did.
Click to expand...
Click to collapse
Edge is better imo, certainly looks better. All you need is Renegade rom anyway. May be a few more roms in active dev for s6 but nothing better per se. Renegade rom dev is alive and well.

Would these root methods trip knox?

chen69chuck said:
Would these root methods trip knox?
Click to expand...
Click to collapse
Yes

Thanks.

Working for g920v 6.0.1?

freaking thank you been struggling with twrp on and off for two days trying to bring this phone back from the dead! YOU the man