1: Goto the market and download the Android VNC program
2: http://downloads.sourceforge.net/vnc-tight/tightvnc-1.3.10-setup.exe (If your using anything other than windows goto their download page, this file is for windows based pc's only)
3: Download #2, run the server and it will ask you to configure it. ALL YOU HAVE TO DO IS SET A PASSWORD THAT IS 8 CHARACTERS OR LESS AND CONFIRM IT. Click ok to finish loading the tightvnc. You should see a small little icon in the lower right corner near the time that looks like a little V
4: http://www.whatismyip.com/ Write down your ip address (you will need this to configure the VNC program to tell it where your computer is on the internet
5: *******THIS IS A LITTLE ADVANCED FOR SOME PEOPLE DONT ATTEMPT IF YOUR NOT COMFORTABLE, GOOGLE SHOULD HAVE A WALKTHROUGH FOR YOUR MODEL OF ROUTER*******
6: This is very important part or it WILL NOT work. To make sure the proper ports are open to allow the vnc program to work
7: click start menu > run (windows vista uses start/search) type cmd, will open a black box up.
8. Type ipconfig into this box. Look for your connection that your using and the gateway ipaddress of that connection (should be along the lines of 192.168.1.1 or 192.168.0.1 or 192.168.1.254 for most mass produced routers, also write down your ip address (IF YOUR USING WINDOWS VISTA YOU ARE LOOKING FOR IP ADDRESSV4 NOT V6)
9: After getting this information, type hostmask and hit enter, write down your computer name
10: Once inside of your router, there will be a dmz option to set (usually within a NAT/QOS menu)
*******This will open all ports on the computer to the internet, if you dont feel comfortable doing this, follow these directions*********
11: goto the port forwarding section (should be in the same area as DMZ)
12: usually theres a nickname you type in to label the port forwarding your doing (label it androidvnc)
13: the FROM port number will be 5800 and TO will be 5900 and make sure to check the enable box (if there is one)
14: once in the DMZ menu input your ipaddressV4 into it and enable dmz mode if a checkmark is needed to enable DMZ for that ip address
15: load AndroidVNC, configure the Nickname with the anything you you wrote down (not sure if this is neccessary, which after research is not needed its just a nickname of the connection your making) type the password that you set within the Tightvnc program, Address is the ip address that you got from www.whatismyip.com, leave the port number the same
16: Connect and once it says "downloading first frame" you are connected and give it a second to work and than you will see the screen in front of you of your pc!
17: Configure AndroidVNC for the color depth that runs the fastest for you, also input should be set to the last one on the list (touch pan trackball mouse or something) which will allow you to pan the screen by touching it and the trackball is now your mouse.
P.S. I used scaling to goto 1:1, not fit to screen as it looked horrible in that mode.
P.S.S. That should do it, now you have a vnc connection made and downloading files while your at work (or whatever have you!) Any questions please feel free to PM me and i will help out to the best i can. If i missed a step please let me know and i will add it, but thats all it should take (had mine working in 5-10 minutes)
P.S.S.S! Everytime you disconnect wirelessly (if you use wireless) or shut your computer down, your IP address will more than likely change, upon reboot you will have to redue this process by getting the newly obtained IP address and changing the port forwarding ip address to reflect your new ip. If you know how to set static IP's.... you probably dont need this tutorial
mine is stuck at handshake.
i have tried everything
i have a 2wire router and i put it into dmz plus mode which allows all incoming connections
inpherno3 said:
1
10: once in the DMZ menu input your ipaddressV4 into it and enable dmz mode if a checkmark is needed to enable DMZ for that ip address
Click to expand...
Click to collapse
Bad idea. You just opened every port on the PC to the world, removing an important layer of protection. Playing around with DMZ is something to be done only if you know the potential consequences.
VNC listens on port 5900/tcp. Only forward that one. Also you'll need to add an exception on any firewall you may have on the PC.
Yes i understood that when writing it, thing is, to walk someone through specifying the port was a little much. People want it working, thats the easiest way.
@kp123: Dont forget to check for a software firewall, if your running vista make sure you allow it through when you run it for the first time.
@TonyHoyle: Most people have a software firewall on their pc's, if not than yes, someone looking to do something can. But thats a slim chance. Oh and tightvnc also uses port 5800. Yes still a port range of 5800-5900 would work.
bump for love
TonyHoyle said:
Bad idea. You just opened every port on the PC to the world, removing an important layer of protection. Playing around with DMZ is something to be done only if you know the potential consequences.
VNC listens on port 5900/tcp. Only forward that one. Also you'll need to add an exception on any firewall you may have on the PC.
Click to expand...
Click to collapse
good point... haha just forwarded port 5900 instead of all ports
I just installed AndroidVNC on my phone... VNC-Tight on my notebook with Windows7.
filled in the same username as notebook
changed password in VNCtight
filled in at my Desire HD
the 192.. ipv4 ip
and connection in 0.5sec
a more secure option
For more security use SSH ( quick version ):
- Forward port 22 instead of 5900 to your PC. The PC must have a SSH server runnign. I have linux so is basically ready, for windows you have to get a ssh server.
- From android use connectbot (from the market) to log into your PC and do a port forwad of 5900 to localhost:5900.
- use android VNC viewer to connect to localhost:5900.
VNC connection through a secure line.
I'm grave digging here but i hit this problem just now I installed CrossLoop on my Laptop Win 7 Ultimate (32-Bit) i set a password, i installed crossloop on my ascend M860 i set the same password i entered my IPv4 into crossloop droid i hit connect it stays on handshake i tried it the other way around still sticks at handshake i have also tried conecting through partner connect and still sticks at handshake. I have forwarded port 4900 TCP on a verizon modem! STILL stuck on handshake any pointers?
I thought I'd be major gravedigging but apparently not.
I used to use this all the time, but it was confusing me today as to why it wasn't working..
Turns out I forgot to portforward!
*facepalm*
So i have the HTC HD2 and want to use the remote desktop which is build in the phone. The problem is that i have no clue how to set up my pc.
Im running on windows xp home edition and using a router. I saw a tutorial for setting it up where he basically told me to open a port and it works. After doing that it didnt work and i suspect there are some things not explained in the tutorial... Can anyone help me out on this?
Will not work on XP Home.
Ah i kinda had that feeling, im trying the same thing on my laptop which is windows xp proffesional. But i still cant log in. I also enabled the "allow remote"
Have you activated "Allow remote assistance" or did you activate "Allow connections" ? The latter is the one you need. Also make sure you're in the list of allowed users.
Doing this off the top of my head, I'm using Vista and it's been a while since I've needed to go into those options in XP.
You must have a password set too, so if the computer boots up and goes straight to your desktop without you having to log in, you'll need to set a password.
To access your computer when on the same network (wifi) use the computer's IP address.
Get this by running cmd on the computer and type ipconfig (then hit return).
To access your computer via the internet (over the phone network) use the computer's external IP address.
Get this by going to whatsmyip.org
You'll also need to configure your router to forward TCP port 3389 to the computer's IP address (found via ipconfig as above).
The thing is, with most home broadband connections, your external IP address can change, so get around this problem by using dynamic DNS.
Some routers have a DDNS client built in, with a list of compatible DDNS services. Just go to one of those services' websites and sign up, often it's free. Pick an domain name to register, ie p03p.dyndns.org, and use that to connect rather than your external IP address.
Best to check you can connect via wifi first using the computer's internal IP address.
If that doesn't work, are you running a firewall?
If you don't have a 3rd party one like Symantec/Norton, then check the windows firewall - ensure the Remote Desktop exception is ticked, if it is, then disable the firewall, and also untick the network connections on the advanced tab (even though the windows firewall says it's disabled, don't expect it to know that!).
If you use a 3rd party firewall, then look into how you can add a rule for port 3389 (RDP)
One way to get around the issue of a dynamic IP address on the home PC is to use Himachi2....it's a super-simple way to create a tunnel to your home pc no matter what the ever-changing external IP address is, and they have a winmo client now too. You simply set up the host once on your home PC, and as long as you leave it running it's very easy to create the remote connection just like you're on the local network with the PC....then you just use Remote Desktop that way
I ticked both the allow options just to be sure. What i also did is go on my 2nd laptop which also has windows xp pro on it to try and connect to my 1st laptop which also didnt work.
I think the problem lies in the list of allowed user. When i get into that list i dont see anyone in it. I assume i have to add my 2nd laptop in that list in order to get this to work. I tried to look a bit arround but i dont know how to add someone to that list.
As the subject states, non of the current roms/kernels appear to have the TUN/TAP driver to run openvpn.
Side note.. ATT pissed me off today (okay so I had it coming for tethering but still..) So, new solution is to run openvpn and force all the traffic through my openvpn gateway, this will keep ATT from spying, and also prevent them from using TTL (still speculation, but one of the methods to detect tethering)
Just out of curiosity, how did you confirm that the TUN/TAP driver was non-existant or not operating properly on the skyrocket?
I'm in the midst of doing the same ... installing openvpn. I have the server set up on my home PC and verified through another laptop off-network. But I have problems when trying to run openvpn settings. Here is what I did:
1) Copied .ovpn file, ca.crt, client1.crt, client1.key, ta.key FROM server TO /sdcard/openvpn directory on skyrocket
2) Installed busybox
3) Installed openvpn installer
4) Installed openvpn using #3
5) Installed and opened openvpn settings
6) Under "OpenVPN Settings" I checked the box saying "OpenVPN"
7) Under "OpenVPN Configurations", I selected my .ovpn file's checkbox
8) The .ovpn checkbox immediately disables and I have no openvpn
Was your approach similar?
I just checked via lsmod. I did not bother going through the process of moving my config files from my captivate to the skyrocket.
Samsung does not include the tun/tap driver in the stock kernel, so it will require a custom kernel, or at least someone to create the module with the same libraries as the stock kernel and just the tun.ko module file to copy across to our current phones.
Actually TUN/TAP is compiled directly into the stock kernel and not compiled as a module so you won't find it with lsmod. You also don't need to do an insmod to use it. I'm running openvpn just fine in tap mode.
There IS a bug in the OpenVPN Installer though that requires you to have ifconfig and route in /system/xbin/bb. It won't work if you select anything else during the openvpn install.
Here's what I did...
Install busybox to /system/xbin
Install openvpn to /system/xbin and select /system/xbin/bb as the location of ifconfig/route
adb shell or use a terminal on the device and do a su.
mount -o rw,remount /dev/block/mmcblk0p24 /system
mkdir /system/xbin/bb
cd /system/xbin/bb
ln -s ../busybox ifconfig
ln -s ../busybox route
mount -o ro,remount /dev/block/mmcblk0p24 /system
Configure and start openvpn.
Good to know.
Will try it in abit, I tried to run openvpn, but it failed on the tun driver, which is why I stopped, but I did not link bb, will give that a try when I get a chance... stupid ATT busted me for unauthorized tethering again.. so cannot get my existing openvpn config from my server yet...
gtj0:
I tried the directions you provided but with using tun and no luck. I'll try and reconfigure my openvpn server to run tap and will try agian.
jvanbrecht:
let me know if you make any progress
plarser48 said:
gtj0:
I tried the directions you provided but with using tun and no luck. I'll try and reconfigure my openvpn server to run tap and will try agian.
jvanbrecht:
let me know if you make any progress
Click to expand...
Click to collapse
I just reconfigured my server over to tun mode and it's still working fine.
Can you try running openvpn from a command line and see what errors it spits out?
I.E. openvpn --config server.ovpn
Also can you check if /dev/tun exists?
edit.....
Here's my config...
client
dev tun0
proto udp
float
remote vpn.example.com 21194
resolv-retry infinite
nobind
persist-key
persist-tun
ca vpn.example.com.ca.crt
cert zzz.crt
key zzz.key
tls-auth vpn.example.com.ta.key 1
cipher AES-256-CBC
comp-lzo
verb 4
mute 20
plarser48 said:
gtj0:
I tried the directions you provided but with using tun and no luck. I'll try and reconfigure my openvpn server to run tap and will try agian.
jvanbrecht:
let me know if you make any progress
Click to expand...
Click to collapse
I had no problems getting it to work, I borrowed my co workers usb modem to pull down my configs from my old Captivate (I use ssl-admin and store the configs with the certificates in zip format).
The problem I am having at the moment is getting tethering to work while openvpn is running.
Laptop can talk to the phone (using wifi tethering, usb tethering kills the adb session, but I suspect it would work just fine), and phone can talk to the world, but laptop will not connect to the world.
The routes are in place, I checked the sysctl options, and ip forwarding is enabled. Just no traffic will pass... it is driving me nuts... heh.
Success for me too! Not sure what was wrong. The server was always working no problem and was always able to connect directly over home wifi from laptop. But I wasn't able to connect on the Skyrocket.
But I used gtj0's config file, changed the remote ip address/port, and worked perfectly. Thanks!
jvanbrecht: I haven't tried it with tethering yet and probably won't get to until at least a few days. Hope to be able to help by trying on my phone sometime soon.
Everyone: Any idea if it is better to run tun or tap for mobile phone openvpn? Regarding tethering, do both tap and tun hide detectable elements like TTL at the IP layer?
EDIT: VPN Not Porting Properly?
Hmm. It seems I am able to connect no problem and openvpn on the phone says it's connected. But when I go to www.whatismyip.com from my phone, it still says an AT&T address. I expected with openvpn running that it should show my home server ip address no? Also, openvpn on skyrocket indicates that it is connected as 10.3.0.6. But if I try to ping 10.3.0.6 from the server I get no response. Is that expected?
plarser48 said:
Success for me too! Not sure what was wrong. The server was always working no problem and was always able to connect directly over home wifi from laptop. But I wasn't able to connect on the Skyrocket.
But I used gtj0's config file, changed the remote ip address/port, and worked perfectly. Thanks!
jvanbrecht: I haven't tried it with tethering yet and probably won't get to until at least a few days. Hope to be able to help by trying on my phone sometime soon.
Everyone: Any idea if it is better to run tun or tap for mobile phone openvpn? Regarding tethering, do both tap and tun hide detectable elements like TTL at the IP layer?
EDIT: VPN Not Porting Properly?
Hmm. It seems I am able to connect no problem and openvpn on the phone says it's connected. But when I go to www whatismyip com from my phone, it still says an AT&T address. I expected with openvpn running that it should show my home server ip address no? Also, openvpn on skyrocket indicates that it is connected as 10.3.0.6. But if I try to ping 10.3.0.6 from the server I get no response. Is that expected?
Click to expand...
Click to collapse
TAP provides a bridged connection so broadcasts on the server's network are propagated across the connection. For network-to-network connections this may be needed for things like dhcp and windows networking. For end users, this usually isn't a good thing because it eats up bandwidth. TUN, which is routed instead of bridged, is the better way to go.
My config only routes traffic destined for the server's LAN over the vpn connection so the behavior you see with whatsmyip is normal. Check openvpn's config file paramters to make the vpn the default route for all traffic.
See my other post. I included my configs.
Just add redirect-gateway option to your client configuration, or the server side client configuration in the ccd directory.
I have everything working. As for what att will see. Only an encrypted tunnel initiated from you phone to your vpn server. Ttl, ip options etc will not be visible to att.
Sent from my SAMSUNG-SGH-I727 using XDA App
Cool thanks again. I'll try updating my configs and trying again tonight. I'm sure not being able to ping across the tunnel was probably a configure issue a well.
You also need the Client to Client option enabled if you want the openvpn server to advertise routes to other vpn client devices and their associated networks. That would be another reason why you cannot ping across the tunnel if you are trying to ping another vpn device.
jvanbrecht:
I'm not seeing your config files on the board here. I'm fairly new here so maybe I'm not looking at the right place. But I didn't see an attachment.
The configs are posted in my other thread.
http://forum.xda-developers.com/showthread.php?t=1378970
Thank you. I'll try out the details in that post. If I have any questions I am going to post over there from now on because that post is more closely aligned with my goal and thus more relevant.
Some research into bypassing T-mobile’s tether restrictions reveals there are several things carriers can do to detect hotspot usage and block those packets:
-is hotspot data sent through a second anp?
-does carrier mark the packets coming through the wlan interface?
-do they filter by user agent strings?
-do they view the ttl?
-do they block urls that phones do not use?
-do they have a monitoring app pre-installed? (ex delete com.tmobile.pr via titanium backup)
Getting around these restrictions while using the native hotspot functionality requires work-arounds that I did not go far enough to successfully implement. One cannot by default edit the APNs for instance. I had to set up a duplicate, but theorize T-mobile was still routing to the hotspot APN I could not edit. With root access (which I have) it should be possible to achieve success, but I have found satisfactory non-root ways of achieving unlimited internet with MetroPCs (owned by T-mobile). I have, however, compiled a number of resources and may look back into what hacks must be used on the native app in the future. If anyone has a good guide on how you're getting hotspot with the Nougat LG V10 please post!
It stands to reason that one must use a non-native application to disguise the tether usage, or significantly modify the native one. After stalling with the mods, I pursued the non-native of attack and found (2) independent working ways to get unlimited tethered internet.
Wifi Tethering apps
I tried various wifi tether apps and without additional modifications or configuration I could not get them to work including:
-native hotspot (which works despite not having a hotspot plan, but t-mobile blocks)
-Wifi tether router by Fabio Grasso ($2.90) (requires root access)--(t-mobile was blocking the connection)—in discussion with developer on how to get working, will update. UPDATE: After back and forth with dev, he recommended using a VPN. His app does route the VPN through the hotspot connection if that feature is toggled. I have not tested. Potentially, changing the TTL of the computer may do something.
-Open Garden Wifi Tether—crashed when attempting to start service
Wifi Direct apps:
Wifi apps such as NetShare (red-themed play store entry is completely free, several paid versions) which use the native wifi direct functionality create a proxy server through which you can connect to via wifi. These DO WORK without additional modifications, but most native desktop apps on your computer cannot access the internet. All websites will load however. You have to set up your internet connection as through a proxy server on the client side but do not need to install additional software. A GOOD OPTION TO HAVE. I have found that one sometimes may need to stop and start the service to get it to give you internet access. The way I do it is start then quickly bring up the wifi menu, computer recognizes the network and connects quickly. If there is too much of a delay between starting and connecting via the client Netshare(Pro) doesn’t seem to work without a quick disable/enable afterwards.
USB tethering apps:
Rely on the phone’s native USB debugging feature in the hidden developer tools menu. (Go to about phone, software info, and tap on build repeatedly until enabled.) NO ROOT required. I tested Easy Tether ($9.99) and ClockWorkMod Tether ($4.99). Both worked well. PDAnet+ may also fall into this category but I have not researched. THIS IS MY PREFERRED METHOD so far. It is also possible to USB tether to certain types of wifi routers and thus get wifi for the home.
-There are PC, Mac, or Linux applications and drivers which must be installed on the computer side.
-Must have USB debugging enabled, and USB options set to Photo Transfer (Media Transfer does not work, and why I originally failed with ClockWorkMod…otherwise probably would have not pursued root!)
-These USB tether apps have the benefit of reducing the heat generated by your phone (no wifi signal generation), so runs cooler (think chips last longer) and uses less energy than when you have wifi hotspot enabled. For this reason, and for the phone being so handy when connected to my laptop, I actually prefer this method. Plus you have access to the pictures and DICM folders of internal storage so you can transfer stuff to the phone fairly immediately. To get full access, however, you’ll have to switch to MTTP mode, which on LG phones such as this V10 will break the internet connection. Other phones may not have this particular issue.
Bluetooth Tether apps:
Easy Tether and probably PDAnet+ support Bluetooth tether. With easy tether I wouldn’t suspect any issues at all using this.
Potential other methods WHICH SEEMED PROMISING, I sorted through a lot! For your inspiration:
-One youtuber mentioned using a desktop hospot application + PDAnet+ to get legit wifi hotspot functionality. The desktop PDAnet+ application apparently disguises the tethering operation. Video here: https://youtu.be/D98abWOkkQI
-Exposed framework and tether for rooted devices (did not try): https://highonandroid.com/android-a...n-rooted-android-att-t-mobile-sprint-verizon/
-Claims you’ll be able to tether any rooted android with this rooted wifi app and particular settings (similar to wifi tether router) https://highonandroid.com/android-a...android-smartphone-or-tablet-universal-guide/ (UPDATE: I tried, app is not compatible with the phone)
See comments section of this article for the below quotes: https://www.groovypost.com/howto/hide-data-usage-get-truly-unlimited-tethering-tmobile-one/
----------------------------------------------------------------------------
“The main issue I see people having is the lack of apn editing. This has been my setup for four years now
-Dd-wrt with iptables to edit the ttl value to 65 -Change TTL on windows PC to 65 so that it appears data is coming from the phone. (41 in hex = 65 in dec) https://social.technet.microsoft.co...o-live-ttl-in-windows?forum=w7itpronetworking
-Changed apn of hotspot to match the apn of normal mobile date. Doesn’t matter if you use fast.xxxx.com or alpha/beta BUT YOU CANT USE THE ORIGINAL HOTSPOT APN it’ll say mobile web or some ****. If you do you will be routed through their hotspot server and tracked. I’ve done this on iOS and android.
-FOR THE FOLKS THAT SAY THE VPN DOESNT WORK. Once again you MUST change the apn AND you have to make sure that your traffic is actually being routed through the VPN, in my experience on both android and iOS hotspot traffic bypass your phones VPN, and VPN on the router/computer traveling through the phone can be tracked if the phone isn’t the one using the VPN, to make it force traffic through the VPN I had to use the for data option in the tether me app on iOS. These things all work if you do it properly.”--Wifi tether router does have this VPN routing function but I have not tested.
"My COMBO works for me on T-Mobile unlimited.
Nexus 5x – rooted 6.01 with “settings put global tether_dun_required 0”
PLUS
Asus n31u router (w/ net.ipv4.ip_default_ttl = 65, bridge mod)
Works for Window 7 desktop and laptop, chromebook, and tablets. All about 80 Gigs last month”
“The TTLstands for “time to live” it is a counter on the data you send for its maximum hop count, or the number of devices it can travel through, for ever device it goes down by one, windows has a default TTL of 128, while Android has one of 64, if you change the TTL for windows to 65 when it gets to the phone the TTL will go down by one makeing it equal 64 the same as the phone. There are more adwanced way to do this so you can run a whole network off this by using a router with either DD-wrt, Tomatos or open-wrt or a dedicated pc running either pfsense, linux, or freebsd to act as a router and mangle the TTl on the fly, the benefits of this is it gets ALL of the data(windows seem to miss a small amount arohnd 5%) and its possible to edit the User agent in ways that dont mess up websites with squid and just appending the device.”
Reserved
For USB tether clients, ClockWorkMod seems to be programmed in a lower-level fashion and produce significantly less heat than running Easytether. I will be monitoring and update.
Arr123 said:
Some research into bypassing T-mobile’s tether restrictions reveals there are several things carriers can do to detect hotspot usage and block those packets:
-is hotspot data sent through a second anp?
-does carrier mark the packets coming through the wlan interface?
-do they filter by user agent strings?
-do they view the ttl?
-do they block urls that phones do not use?
-do they have a monitoring app pre-installed? (ex delete com.tmobile.pr via titanium backup)
Getting around these restrictions while using the native hotspot functionality requires work-arounds that I did not go far enough to successfully implement. One cannot by default edit the APNs for instance. I had to set up a duplicate, but theorize T-mobile was still routing to the hotspot APN I could not edit. With root access (which I have) it should be possible to achieve success, but I have found satisfactory non-root ways of achieving unlimited internet with MetroPCs (owned by T-mobile). I have, however, compiled a number of resources and may look back into what hacks must be used on the native app in the future. If anyone has a good guide on how you're getting hotspot with the Nougat LG V10 please post!
It stands to reason that one must use a non-native application to disguise the tether usage, or significantly modify the native one. After stalling with the mods, I pursued the non-native of attack and found (2) independent working ways to get unlimited tethered internet.
Wifi Tethering apps
I tried various wifi tether apps and without additional modifications or configuration I could not get them to work including:
-native hotspot (which works despite not having a hotspot plan, but t-mobile blocks)
-Wifi tether router by Fabio Grasso ($2.90) (requires root access)--(t-mobile was blocking the connection)—in discussion with developer on how to get working, will update. UPDATE: After back and forth with dev, he recommended using a VPN. His app does route the VPN through the hotspot connection if that feature is toggled. I have not tested. Potentially, changing the TTL of the computer may do something.
-Open Garden Wifi Tether—crashed when attempting to start service
Wifi Direct apps:
Wifi apps such as NetShare (red-themed play store entry is completely free, several paid versions) which use the native wifi direct functionality create a proxy server through which you can connect to via wifi. These DO WORK without additional modifications, but most native desktop apps on your computer cannot access the internet. All websites will load however. You have to set up your internet connection as through a proxy server on the client side but do not need to install additional software. A GOOD OPTION TO HAVE. I have found that one sometimes may need to stop and start the service to get it to give you internet access. The way I do it is start then quickly bring up the wifi menu, computer recognizes the network and connects quickly. If there is too much of a delay between starting and connecting via the client Netshare(Pro) doesn’t seem to work without a quick disable/enable afterwards.
USB tethering apps:
Rely on the phone’s native USB debugging feature in the hidden developer tools menu. (Go to about phone, software info, and tap on build repeatedly until enabled.) NO ROOT required. I tested Easy Tether ($9.99) and ClockWorkMod Tether ($4.99). Both worked well. PDAnet+ may also fall into this category but I have not researched. THIS IS MY PREFERRED METHOD so far. It is also possible to USB tether to certain types of wifi routers and thus get wifi for the home.
-There are PC, Mac, or Linux applications and drivers which must be installed on the computer side.
-Must have USB debugging enabled, and USB options set to Photo Transfer (Media Transfer does not work, and why I originally failed with ClockWorkMod…otherwise probably would have not pursued root!)
-These USB tether apps have the benefit of reducing the heat generated by your phone (no wifi signal generation), so runs cooler (think chips last longer) and uses less energy than when you have wifi hotspot enabled. For this reason, and for the phone being so handy when connected to my laptop, I actually prefer this method. Plus you have access to the pictures and DICM folders of internal storage so you can transfer stuff to the phone fairly immediately. To get full access, however, you’ll have to switch to MTTP mode, which on LG phones such as this V10 will break the internet connection. Other phones may not have this particular issue.
Bluetooth Tether apps:
Easy Tether and probably PDAnet+ support Bluetooth tether. With easy tether I wouldn’t suspect any issues at all using this.
Potential other methods WHICH SEEMED PROMISING, I sorted through a lot! For your inspiration:
-One youtuber mentioned using a desktop hospot application + PDAnet+ to get legit wifi hotspot functionality. The desktop PDAnet+ application apparently disguises the tethering operation. Video here: https://youtu.be/D98abWOkkQI
-Exposed framework and tether for rooted devices (did not try): https://highonandroid.com/android-a...n-rooted-android-att-t-mobile-sprint-verizon/
-Claims you’ll be able to tether any rooted android with this rooted wifi app and particular settings (similar to wifi tether router) https://highonandroid.com/android-a...android-smartphone-or-tablet-universal-guide/ (UPDATE: I tried, app is not compatible with the phone)
See comments section of this article for the below quotes: https://www.groovypost.com/howto/hide-data-usage-get-truly-unlimited-tethering-tmobile-one/
----------------------------------------------------------------------------
“The main issue I see people having is the lack of apn editing. This has been my setup for four years now
-Dd-wrt with iptables to edit the ttl value to 65 -Change TTL on windows PC to 65 so that it appears data is coming from the phone. (41 in hex = 65 in dec) https://social.technet.microsoft.co...o-live-ttl-in-windows?forum=w7itpronetworking
-Changed apn of hotspot to match the apn of normal mobile date. Doesn’t matter if you use fast.xxxx.com or alpha/beta BUT YOU CANT USE THE ORIGINAL HOTSPOT APN it’ll say mobile web or some ****. If you do you will be routed through their hotspot server and tracked. I’ve done this on iOS and android.
-FOR THE FOLKS THAT SAY THE VPN DOESNT WORK. Once again you MUST change the apn AND you have to make sure that your traffic is actually being routed through the VPN, in my experience on both android and iOS hotspot traffic bypass your phones VPN, and VPN on the router/computer traveling through the phone can be tracked if the phone isn’t the one using the VPN, to make it force traffic through the VPN I had to use the for data option in the tether me app on iOS. These things all work if you do it properly.”--Wifi tether router does have this VPN routing function but I have not tested.
"My COMBO works for me on T-Mobile unlimited.
Nexus 5x – rooted 6.01 with “settings put global tether_dun_required 0”
PLUS
Asus n31u router (w/ net.ipv4.ip_default_ttl = 65, bridge mod)
Works for Window 7 desktop and laptop, chromebook, and tablets. All about 80 Gigs last month”
“The TTLstands for “time to live” it is a counter on the data you send for its maximum hop count, or the number of devices it can travel through, for ever device it goes down by one, windows has a default TTL of 128, while Android has one of 64, if you change the TTL for windows to 65 when it gets to the phone the TTL will go down by one makeing it equal 64 the same as the phone. There are more adwanced way to do this so you can run a whole network off this by using a router with either DD-wrt, Tomatos or open-wrt or a dedicated pc running either pfsense, linux, or freebsd to act as a router and mangle the TTl on the fly, the benefits of this is it gets ALL of the data(windows seem to miss a small amount arohnd 5%) and its possible to edit the User agent in ways that dont mess up websites with squid and just appending the device.”
Click to expand...
Click to collapse
I recently been looking into this as well. I've currently been using the new pdanet with with wifi direct but it seem to be hit or miss when getting a internet connection when using the proxy method. I have a few devices where i cant install the interface so im looking for reliable method
Few scenarios im looking at. The first one you cover quite a bit, was wondering if your using IPV4 or IPV6 with your different apn settings? 2nd scenario is being able to tether when connected to wifi like from a hotel and being able to pass that to other devices and the 3rd is being able to pass along a vpn connection if connected to free wifi places
Sorry for the necropost, I just wanted to point out that currently the only method you can use to hide tethering from T-mo is PDANet with it's "Hide Tether Usage" feature.
All other methods are detected and if you have tethering, will count against your tethering allotment.
majikfox said:
Sorry for the necropost, I just wanted to point out that currently the only method you can use to hide tethering from T-mo is PDANet with it's "Hide Tether Usage" feature.
All other methods are detected and if you have tethering, will count against your tethering allotment.
Click to expand...
Click to collapse
Thanks for the heads up. Just wanted to make sure since I wanted to try the TTL method, but that is also blocked by T-Mobile correct?
TTL 65 didn't work on my computers, but 85 and 99 did. So don't be afraid to try different things.
However, the phone should be able to modify the TTL before it forwards the packet. How is there not an app that does this, or is there a setting or hack we can do to make it change the TTL as it passes through the phone?
edit: have searched more and learned some apps do, but they don't work on my phone. Not sure why.
I have metro pcs with 15gb of hotspot data.. i run out every month.. once my data runs out i use hotspotvpn. A free app on the google play store and it works for everything.. been doing it for months..never had any issues
CHEEF WALKING-FROG said:
I have metro pcs with 15gb of hotspot data.. i run out every month.. once my data runs out i use hotspotvpn. A free app on the google play store and it works for everything.. been doing it for months..never had any issues
Click to expand...
Click to collapse
Which one do you use? I saw a few that had the same name
Same here metro
13crigby said:
Which one do you use? I saw a few that had the same name
Click to expand...
Click to collapse
Im also wondering which app you're referring to. Theres quite a few with that name
CHEEF WALKING-FROG said:
I have metro pcs with 15gb of hotspot data.. i run out every month.. once my data runs out i use hotspotvpn. A free app on the google play store and it works for everything.. been doing it for months..never had any issues
Click to expand...
Click to collapse
Let me third the request. I just clocked through 8 or 9 different apps with that name. Who is the publisher?
Thanks!
Bypass With Termux
I've done this for ever and it's not going to be restricted to who you have but it will 100 percent get around any data throttling.
Download Termux app and install openssh-server on it. Go ahead and hotspot your phone, then run ifconfig inside Termux to get your current tethering local IP. It will be the only 192. spit out when you run ifconfig. Save this. Run sshd -dD inside Termux which starts an openssh server waiting to be connected to in debug mode to audit traffic. Now pop onto a PC or router you can SSH into, whatever and connect it to your hotspot from your phone. Now SSH tunnel all the traffic from the device back through the openssh server your running on the Termux app. Now that you are on the same local network you can SSH tunnel into that IP address you saved earlier. As long as you make sure all your traffic passes through the tunnel it 100 percent shows that all your internet is being used by Termux app not your hotspot app so you need no other spoofing of hops or anything because to your phone and carrier you are just using a bunch of data in termux, you do it right you will never be throttled I've used 150GB data multiple times.
Step by step > https://github.com/RiFi2k/unlimited-tethering
RiFi2k said:
I've done this for ever and it's not going to be restricted to who you have but it will 100 percent get around any data throttling.
Download Termux app and install openssh-server on it. Go ahead and hotspot your phone, then run ifconfig inside Termux to get your current tethering local IP. It will be the only 192. spit out when you run ifconfig. Save this. Run sshd -dD inside Termux which starts an openssh server waiting to be connected to in debug mode to audit traffic. Now pop onto a PC or router you can SSH into, whatever and connect it to your hotspot from your phone. Now SSH tunnel all the traffic from the device back through the openssh server your running on the Termux app. Now that you are on the same local network you can SSH tunnel into that IP address you saved earlier. As long as you make sure all your traffic passes through the tunnel it 100 percent shows that all your internet is being used by Termux app not your hotspot app so you need no other spoofing of hops or anything because to your phone and carrier you are just using a bunch of data in termux, you do it right you will never be throttled I've used 150GB data multiple times.
Click to expand...
Click to collapse
This is amazing. How do I use my Windows PC to connect to the openSSH server to create the traffic tunnel? Also, how do I force my Windows 10 traffic through the tunnel?
I am guessing with Putty and then setup SSH proxy in a browser to force traffic? Won't that only allow browser based traffic through the tunnel and not all traffic from the Windows computer?
VICosPhi said:
This is amazing. How do I use my Windows PC to connect to the openSSH server to create the traffic tunnel? Also, how do I force my Windows 10 traffic through the tunnel?
I am guessing with Putty and then setup SSH proxy in a browser to force traffic? Won't that only allow browser based traffic through the tunnel and not all traffic from the Windows computer?
Click to expand...
Click to collapse
So I am an everyday linux user and for me personally I use sshuttle to route everything back through the tunnel because it already handles the TCP over TCP problem because the guy that wrote it is a boss. This here explains that.
If I was on windows I would go with their vagrant solution because then you get the benefit of sshuttle and all your responsible for is making sure all traffic goes through the VM. Also you could use something like proxycap and putty works as well although I guess it's slow people have said.
Browser traffic can be handled with SOCKS proxies.
I feel like it's a pretty great solution overall and can benefit some people so I started a repo and I'll fully document how it works, I'm just too tired tonight so keep an eye out https://github.com/RiFi2k/unlimited-tethering and I'll step by step linux and windows for everyone as much as possible, plus if anyone else has scripts and whatnot feel free to contribute.
RiFi2k said:
So I am an everyday linux user and for me personally I use sshuttle to route everything back through the tunnel because it already handles the TCP over TCP problem because the guy that wrote it is a boss. This here explains that.
If I was on windows I would go with their vagrant solution because then you get the benefit of sshuttle and all your responsible for is making sure all traffic goes through the VM. Also you could use something like proxycap and putty works as well although I guess it's slow people have said.
Browser traffic can be handled with SOCKS proxies.
I feel like it's a pretty great solution overall and can benefit some people so I started a repo and I'll fully document how it works, I'm just too tired tonight so keep an eye out https://github.com/RiFi2k/unlimited-tethering and I'll step by step linux and windows for everyone as much as possible, plus if anyone else has scripts and whatnot feel free to contribute.
Click to expand...
Click to collapse
Thanks a lot, will read up on this. Adding your github to my bookmarks as well. :good:
RiFi2k said:
I've done this for ever and it's not going to be restricted to who you have but it will 100 percent get around any data throttling.
Download Termux app and install openssh-server on it. Go ahead and hotspot your phone, then run ifconfig inside Termux to get your current tethering local IP. It will be the only 192. spit out when you run ifconfig. Save this. Run sshd -dD inside Termux which starts an openssh server waiting to be connected to in debug mode to audit traffic. Now pop onto a PC or router you can SSH into, whatever and connect it to your hotspot from your phone. Now SSH tunnel all the traffic from the device back through the openssh server your running on the Termux app. Now that you are on the same local network you can SSH tunnel into that IP address you saved earlier. As long as you make sure all your traffic passes through the tunnel it 100 percent shows that all your internet is being used by Termux app not your hotspot app so you need no other spoofing of hops or anything because to your phone and carrier you are just using a bunch of data in termux, you do it right you will never be throttled I've used 150GB data multiple times.
Step by step > https://github.com/RiFi2k/unlimited-tethering
Click to expand...
Click to collapse
Had any user tried this already and confirm that it works with metropcs?
Pdanet+ documentation details that only usb tether+hide tether usage works with metropcs. It took me a while to go around all of it, but I haven't tested due to I want to switch carriers to metropcs.
RiFi2k said:
I've done this for ever and it's not going to be restricted to who you have but it will 100 percent get around any data throttling.
Download Termux app and install openssh-server on it. Go ahead and hotspot your phone, then run ifconfig inside Termux to get your current tethering local IP. It will be the only 192. spit out when you run ifconfig. Save this. Run sshd -dD inside Termux which starts an openssh server waiting to be connected to in debug mode to audit traffic. Now pop onto a PC or router you can SSH into, whatever and connect it to your hotspot from your phone. Now SSH tunnel all the traffic from the device back through the openssh server your running on the Termux app. Now that you are on the same local network you can SSH tunnel into that IP address you saved earlier. As long as you make sure all your traffic passes through the tunnel it 100 percent shows that all your internet is being used by Termux app not your hotspot app so you need no other spoofing of hops or anything because to your phone and carrier you are just using a bunch of data in termux, you do it right you will never be throttled I've used 150GB data multiple times.
Step by step > https://github.com/RiFi2k/unlimited-tethering
Click to expand...
Click to collapse
Hey bro!! Thank you !!
This is great idea, I would try it on my country to see if this works
myself379 said:
Hey bro!! Thank you !!
This is great idea, I would try it on my country to see if this works
Click to expand...
Click to collapse
For sure! See the nice thing about this method is that your phone doesn't register any of the data used as coming from the tethering app, it 100% all gets attributed to the Termux app because of the SSH tunnel. So basically there is no way for anyone at your carrier to know, or prove that you actually were tethering at all. If you open up the apps section and check out the part where it shows you how much data each app used you will see what I mean. So basically it really doesn't matter what country / carrier / phone you have, as long as you have access to be able to tether and you have a computer you can use for the SSH tunnel it's impossible for them to throttle you because they can't prove you actually used the data tethering. When you read the fine print about them throttling it basically says the same thing, if they can't definitively prove the data came from tethering it doesn't go on your tethering cap.
Hello RiFi2k,
OK, thanks for the information. I'm trying to translate this into a windows environment(Windows 10 phone and PC).
Here is what I have so far, but a few of your points are unclear. A little clarity would be fantastic.
Translation for Windows 10 phone
Since, I'm on a windows phone there is no Termux app. I guess Termux is used to install the SSH server and gain access to a command prompt, correct?
1. Ok since openssh server is built into the windows phone OS and I can access the command prompt via putty, I should be fine, right.
2. Generate key pair and stored public key on phone. Working fine.
3. Hotspot connection to phone.
4. Run ipconfig(windows) on phone or local machine. On local machine, gateway address is the needed ip, same as hotspot address on phone.
5. SSH Server is started on phone once the phone is placed in development mode.
Can't put server in debug mode on phone, but I'm pretty certain that it's hard coded to listen on port 22.
6. Your instructions on github.com have duplicated the step number 5, which should be 6 and I am having a little trouble sorting through it.
7. I guess the only way to tunnel to the phone is to run a putty session from the Windows machine configured per your instructions.
Are these commands executed on the device or phone?:
ssh -D 8123 -fqgN [email protected].1 -p 22 (ssh client)
sshuttle -r [email protected].1:22 0.0.0.0/0 0.0.0.0 (sock proxy)
Either way, I will need to use putty for the SSH Client portion. What are the switches in your example "-fqgN"? Are the switches concatenated?
-f Specifies a per-user configuration file.
-q Quiet mode
-g Allows remote hosts to connect to local forwarded ports.
-N ???
And finally, depending on where the above commands are run, I will need to find a sock proxy solution, if I want all traffic going through the tunnel.
Again, thanks for all your hard work.
davy4620 said:
Hello RiFi2k,
OK, thanks for the information. I'm trying to translate this into a windows environment(Windows 10 phone and PC).
Here is what I have so far, but a few of your points are unclear. A little clarity would be fantastic.
Translation for Windows 10 phone
Since, I'm on a windows phone there is no Termux app. I guess Termux is used to install the SSH server and gain access to a command prompt, correct?
1. Ok since openssh server is built into the windows phone OS and I can access the command prompt via putty, I should be fine, right.
2. Generate key pair and stored public key on phone. Working fine.
3. Hotspot connection to phone.
4. Run ipconfig(windows) on phone or local machine. On local machine, gateway address is the needed ip, same as hotspot address on phone.
5. SSH Server is started on phone once the phone is placed in development mode.
Can't put server in debug mode on phone, but I'm pretty certain that it's hard coded to listen on port 22.
6. Your instructions on github.com have duplicated the step number 5, which should be 6 and I am having a little trouble sorting through it.
7. I guess the only way to tunnel to the phone is to run a putty session from the Windows machine configured per your instructions.
Are these commands executed on the device or phone?:
ssh -D 8123 -fqgN [email protected].1 -p 22 (ssh client)
sshuttle -r [email protected].1:22 0.0.0.0/0 0.0.0.0 (sock proxy)
Either way, I will need to use putty for the SSH Client portion. What are the switches in your example "-fqgN"? Are the switches concatenated?
-f Specifies a per-user configuration file.
-q Quiet mode
-g Allows remote hosts to connect to local forwarded ports.
-N ???
And finally, depending on where the above commands are run, I will need to find a sock proxy solution, if I want all traffic going through the tunnel.
Again, thanks for all your hard work.
Click to expand...
Click to collapse
Ok, so the N is `-N Do not execute a remote command. This is useful for just forwarding ports (protocol version 2 only).` reference https://linux.die.net/man/1/ssh
It's completely fine if you don't have debug mode on when you start the sshd server on your phone, you actually don't technically need any flags. One is debug and one is detached so it runs in the background, which you are generally going to want.
Both those commands are run on your computer, but you only use one or the other. Follow my link to sshuttle they have information for using it on Windows, it will transparently route all your traffic through the tunnel for you already so it's way better than anything else.
So just to recap, you start the sshd (ssh server) on your phone and it will spit out a port. Then you go to your PC and ssh or sshuttle (ssh client) connect to your phone.
I'm around if you need more help!
---------- Post added at 12:44 AM ---------- Previous post was at 12:40 AM ----------
Also once you get it working on Windows with your phone if you don't mind letting me know what version of Windows and what model your phone is, and where the directions hung you up, because I'll mention it all to help the next person.
Thanks for the quick reply. I'm going to have to dig a little deeper. It looks as if Microsoft is doing some kind of filtering on the WiFi interface and blocking this approach. Again, thanks for the great start.