Device details:
N8010
Installed ROM: CM11 rooted
Recovery: CWM Recovery v6.0.3.6
Problem:
Device will not boot, but is stuck on "Samsung GALAXY Note 10.1" screen
when powering on the "Samsung GALAXY Note 10.1" screen comes on, then after a few seconds the screen gets slightly brighter but thats it.
I can boot into CWM but it will give me the following output:
Code:
Warning: No file_contexts
E: Can't open cache/recovery/log
E: Can't open cache/recovery/last_log
E: Can't open cache/recovery/last_log
I can boot into ODIN (v3.09 Techbeasts) and seemingly install stock firmware etc but it does neither solve the booting problem nor do i get the stock recovery or TWRP if i try to install that. Heres the log of my latest try to install stock firmware
Code:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N8010XXUDNE4_N8010OXADNE4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> param.bin
<ID:0/006> tz.img
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img
<ID:0/006> cache.img
<ID:0/006> hidden.img
<ID:0/006> RQT_CLOSE !!
<ID:0/006> RES OK !!
<ID:0/006> Removed!!
<ID:0/006> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
What i also tried was to delete the NAND completely but that gives me the following in ODIN
Code:
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Erase...
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Connecting via adb seems fine and mounting the external_sd also works
Any Ideas what i can try?
At this point I obviously dont care about any data left on the device, i just want to be able to use it again
Related
Can anyone help me root this phone? I bought it in China last year. So it has Samsungs Chinese thing on it, and I cannot read that.
Here is a link to screenshots from CPU-Z. ( http://imgur.com/a/oedjS#BCaZQvo )
Whenever I try to Use Odin 3.10.6 and 3.12.3 it always stops at: Write NAND start!! I have tried CF-autoroot, TWRP (different versions) and flashify to no avail.
Here is the image I get when I go into download mode, ( http://imgur.com/asckmRm ) when I press volume up it says on screen ODIN mode, the model of the phone, and that it is in fact in download mode. ( http://imgur.com/fyKxoMG )
Here is the image that pops up the moment I press start in Odin ( http://imgur.com/8HadBkP )
Auto reboot under options in Odin is disabled.
The phone is running Android 5.0.2, and the boot loader and kernel version is G9200ZCU1AOE4 as confirmed by CPU-Z.
Does anyone have any tricks? All the links on page 1 on google after countless searches have been clicked, and I am still not any closer to achieve this.
I broke the screen on my main phone, so I need to use this until I can afford a new one, but the Chinese OS and no Google apps makes it impossible to use. It is also prone to random reboots. I have changed the battery, so now I do not know if it is hardware or software related.
Log for CF-autoroot
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-zerofltechn-zerofltezh-smg9200.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1005)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Log for TWRP:
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1005)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Hello there,
I have successfully rooted my phone which was running stock Android Marshmallow v6.0.1.
The problem started when i turned off developer options by accident and not knowing that there was the option that disables FRP Lock.I restarted my phone and now im stuck in a boot loop displaying " Custom binary blocked by FRP. "
Is there any way to bypass this or am i screwed?
Thanks in advance
TheBeerAddict said:
Hello there,
I have successfully rooted my phone which was running stock Android Marshmallow v6.0.1.
The problem started when i turned off developer options by accident and not knowing that there was the option that disables FRP Lock.I restarted my phone and now im stuck in a boot loop displaying " Custom binary blocked by FRP. "
Is there any way to bypass this or am i screwed?
Thanks in advance
Click to expand...
Click to collapse
Greetings and welcome to assist. The easiest way to fix your phone is to reflash the latest stock firmware for your phone with odin/kies and then reroot
Good Luck
Sawdoctor
sawdoctor said:
Greetings and welcome to assist. The easiest way to fix your phone is to reflash the latest stock firmware for your phone with odin/kies and then reroot
Good Luck
Sawdoctor
Click to expand...
Click to collapse
I downloaded the official firmware from sammobile.com/firmwares and followed the steps that are listed below for flashing it.
Im getting Fail in Odin and an error message on my phone which says:
Volume Size is too big 143360 < 409600
ODIN : Invalid ext4 image
Odin logs:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1101)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> sbl1.mbn
<ID:0/006> rpm.mbn
<ID:0/006> tz.mbn
<ID:0/006> hyp.mbn
<ID:0/006> NON-HLOS.bin
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img.ext4
<ID:0/006> cache.img.ext4
<ID:0/006> hidden.img.ext4
<ID:0/006> FAIL! (Ext4)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Ive tried this procedure in Odin versions: v3.11.1 , v3.09 , v1.85
TheBeerAddict said:
I downloaded the official firmware from sammobile.com/firmwares and followed the steps that are listed below for flashing it.
Im getting Fail in Odin and an error message on my phone which says:
Volume Size is too big 143360 < 409600
ODIN : Invalid ext4 image
Odin logs:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1101)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> sbl1.mbn
<ID:0/006> rpm.mbn
<ID:0/006> tz.mbn
<ID:0/006> hyp.mbn
<ID:0/006> NON-HLOS.bin
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img.ext4
<ID:0/006> cache.img.ext4
<ID:0/006> hidden.img.ext4
<ID:0/006> FAIL! (Ext4)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Ive tried this procedure in Odin versions: v3.11.1 , v3.09 , v1.85
Click to expand...
Click to collapse
Ok that is normally a csc issue, some carriers have a smaller csc partition. I'd try using kies/smart switch
Sent from my Mi Max using Tapatalk
Hello there!
My phone is in Bootloop and i'm trying to flash the original firmware with Odin, but i'm getting an fail:
Odin error:
<ID:0/006> Removed!!
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1205)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> boot.img
<ID:0/006> cache.img
<ID:0/006> cm.bin
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Phone error:
[CM] SW REV. check fail device: 5, binary 3
I'm from Netherlands, with an unlocked phone but i'm Using Vodafone as a provider.
Can someone please help me in the right direciton.
thanks in advance!
EDIT: Fixed the problem myself
for those wanne know how: I tried to flash a different firmware and that worked.
bro try a firmware with 4 files just google it
i have a s7 sm-g930vl and got odin to flash it to sm-g930v and it failed with a auth fail and now all i get to a boot recovery loop and download mode can someone help the fix me phone
Someone here had the same problem but fixed it just flashing the 4 ROM sections
https://forum.xda-developers.com/galaxy-s7/help/screwed-sm-g930vl-please-help-t3416539
Check "Repartition" in ODIN settings if you're changing CSC
Use ODIN 3.12.3 or newer
*Detection* said:
Someone here had the same problem but fixed it just flashing the 4 ROM sections
https://forum.xda-developers.com/galaxy-s7/help/screwed-sm-g930vl-please-help-t3416539
Check "Repartition" in ODIN settings if you're changing CSC
Use ODIN 3.12.3 or newer
Click to expand...
Click to collapse
it still failed to flash
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1203)..
<ID:0/006> File analysis..
<ID:0/006> skip file list for home binary
<ID:0/006> Home Binary Download
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> cache.img.ext4
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Wjb89 said:
it still failed to flash
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1203)..
<ID:0/006> File analysis..
<ID:0/006> skip file list for home binary
<ID:0/006> Home Binary Download
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> cache.img.ext4
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Try flashing without the BL section of the ROM
nop
*Detection* said:
Try flashing without the BL section of the ROM
Click to expand...
Click to collapse
fail
<ID:0/006> Odin engine v(ID:3.1203)..
<ID:0/006> File analysis..
<ID:0/006> skip file list for home binary
<ID:0/006> persist.img.ext4
<ID:0/006> Home Binary Download
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img.ext4
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
G930U firmware works on the G930V and VL according to XDA
http://forum.xda-developers.com/showpost.php?p=71418277&postcount=3
Try the G930U firmware
I've been trying for a few weeks to flash a combination firmware on my Galaxy Tab E (SM-T377W) and have been unsuccessful. I managed to get the original firmware back to it. But every time I try to flash the combination firmware to it with Odin it gives me this log.
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1401)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 959 M
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I've Tried both
COMBINATION_OYA_FA60_T377WVLU2AQG1_OYAFAC_.tar.md5
COMBINATION_OYA_FA60_T377WVLU2API1_OYAFAC_.tar.md5
But to no avail could really use some help. Thank you
(Fixed) by @hainguyenthao
An amazing person who took the time to deal with me even when I was being stupid
10/10
would recommend
Hint: Add Galaxy Tab E (SM-T377W) to this thread's title thus mainly owners of such phone get addressed.
(Fixed) by @hainguyenthao
The_One_True_Bean said:
I've been trying for a few weeks to flash a combination firmware on my Galaxy Tab E (SM-T377W) and have been unsuccessful. I managed to get the original firmware back to it. But every time I try to flash the combination firmware to it with Odin it gives me this log.
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1401)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 959 M
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I've Tried both
COMBINATION_OYA_FA60_T377WVLU2AQG1_OYAFAC_.tar.md5
COMBINATION_OYA_FA60_T377WVLU2API1_OYAFAC_.tar.md5
But to no avail could really use some help. Thank you
(Fixed) by @hainguyenthao
An amazing person who took the time to deal with me even when I was being stupid
10/10
would recommend
Click to expand...
Click to collapse
Hello There,
May I know how you fixed the issue and what are the steps you did?