hey guys,
i've a big problem with my Samsung P6800.
After problems with CM9, i got a Bootloop and an error within CWM: Davlik Cache -> E:unknown volume for path [sd-ext]
So I tried restoring an old NAND-Backup, but of course without SD access I wasn't successful.
Next option: Get back to Stock Rom via ODIN (the first time ODIN was closed by Windows during the flash action):
1. Start Odin and select the pit file from Sammobile
2. Plug in Tab in Download Mode
3. "Start" -> Success
4. Unplug
5. Select the newest ATO (P6800XXLQ2_P6800OXALQ2_ATO) in "PDA"-Field
6. Plug in Tab in Download Mode
7. "Start" -> Fail-Message when trying to Flash "KERNEL".
What can I do? Is it right to only select the ROM in the PDA field?
I don't have any access to the recovery anymore.
If you have any solution or tipp, please let me know
greetz!
Thomas
Install XXLPY Android 4.1.2 Jelly Bean Firmware on I9070 Galaxy S Advance
LINK-
http://www.hotfile.com/dl/187838919/fd98d34/I9070XXLPY_I9070SERLPY_SER.zip.html
STEPS-
Android 4.1.2 Official Firmware
1.Extract Firmware zip file that you downloaded already from above link, you will get a .tar file and some other files.
2.Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
3.Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
4.Now, put the Galaxy S Advance I9070 phone in Download Mode by pressing pressing and holding down the Volume Down and Home buttons while pressing the Power button until you are welcomed by a green robot indicating you are in Download Mode.
5.Now run Odin3 v3.07.exe (see Step 2) as an Administrator because Admin privileges is required to complete the process smoothly.
6.Now connect your Galaxy S Advance GT-I9070 with your PC using USB cable. A message will arrive under Odin’s message box in the bottom left saying “Added!!”. If you don’t get the same then you should try another USB port (try USB port located in back in your desktop PC). If that too don’t work then you should then reinstall the driver. If you successfully see the “Added!!” message in Odin then you are ready to go in next step. You should also see COM port with a number in Yellow if you successfully added your device.
7.Select these files in Odin at respective buttons from extracted I9070XXLPY firmware folder :
a)Click the PDA Button, and select the .tar file here with *code* appearing in its name
8.in Odin window, make sure Auto Reboot and F. Reset Time checkboxes are selected. Also, make sure that Re-Partition checkbox is selected, only if you are using a .pit file (see Step 7.4).
9.Double check everything that we mentioned in Step 7 & Step 8 above. Now, once satisfied hit the START button to begin the flashing process.
10.Once flashing completed, the phone will reboot automatically and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can then unplug the USB cable to disconnect your device from computer.
NOTE-If you have PARAMETER ERROR delete.md5,extension should end with .tar and put it in PDA.
ROOT(by shaaan)
How to :
1. Download the zip and place it in the root of your sd card.
PS : SD Card is a must.
2. Reboot to the stock recovery.
3. Select install update from external storage.
4. Select the root.zip file.
5. Viola
Enjoy your rooted JB.
LINK- http://d-h.st/ook
Thread already there under general.
http://forum.xda-developers.com/showthread.php?t=2086965
Reported.
hmm
thats was not a proper guide,
you edited it later.
Perform a factory reset after booting 4.1.2 ... else you will get "Insert SIM card" error.
Thread closed, its pretty much the same as this one >>> http://forum.xda-developers.com/showthread.php?t=2086965
Hi all i tried to flash i9003 galaxy SL from steps below to 2.3.6 , but the firmware zip file does not have MODEM, CSC and PDA files but only .dll file and tar.md5 file, where can i get the MODEM, CSC and PDA.
I download the firmwares from link below:-
http://www.tsar3000.com/Joomla/inde...alaxy-sl-firmwares&catid=55:samsung&Itemid=82
Firmware Update Steps:
Run Samsung I9003 Galaxy SL Downloader.
Check Re-Partition, Auto Reboot and F. Reset Time.
Click PIT button and select this file: latona_20110114.pit
Put your phone into download mode: Press Volume down + OK + Power.
Connect USB cable and the program will detect the phone's Com number.
Click Start button to download the PIT file to phone.
After it is Done Click on Reset button, then unselect Re-Partition box.
Click PDA button and select this file: I9003xxxxx-xxx...-PDA-low-CL890053.tar.md5 <<<<<<<<<<<<<<<
Click PHONE button and select this file: MODEM_I9003xxxxx_REV_00_CL889972.tar.md5 <<<<<<<<<<<<<<<<<
Click CSC button and select this file: GT-I9003-CSC-xxxxxx.tar.md5 <<<<<<<<<<<<<<<<<<<
Remove the battery, then enter Device into Download Mode again.
Click Start button to flash these files to phone.
Do not touch anything till you see PASS on the program window.
Do full reset by this Code: *2767*3855#.wares i download dont have CSC , PDA
suhailpuri said:
Hi all i tried to flash i9003 galaxy SL from steps below to 2.3.6 , but the firmware zip file does not have MODEM, CSC and PDA files but only .dll file and tar.md5 file, where can i get the MODEM, CSC and PDA.
I download the firmwares from link below:-
http://www.tsar3000.com/Joomla/inde...alaxy-sl-firmwares&catid=55:samsung&Itemid=82
Firmware Update Steps:
Run Samsung I9003 Galaxy SL Downloader.
Check Re-Partition, Auto Reboot and F. Reset Time.
Click PIT button and select this file: latona_20110114.pit
Put your phone into download mode: Press Volume down + OK + Power.
Connect USB cable and the program will detect the phone's Com number.
Click Start button to download the PIT file to phone.
After it is Done Click on Reset button, then unselect Re-Partition box.
Click PDA button and select this file: I9003xxxxx-xxx...-PDA-low-CL890053.tar.md5 <<<<<<<<<<<<<<<
Click PHONE button and select this file: MODEM_I9003xxxxx_REV_00_CL889972.tar.md5 <<<<<<<<<<<<<<<<<
Click CSC button and select this file: GT-I9003-CSC-xxxxxx.tar.md5 <<<<<<<<<<<<<<<<<<<
Remove the battery, then enter Device into Download Mode again.
Click Start button to flash these files to phone.
Do not touch anything till you see PASS on the program window.
Do full reset by this Code: *2767*3855#.wares i download dont have CSC , PDA
Click to expand...
Click to collapse
First of all post in the general section. Second, read a lot.
Thirdly, which firmware are you at present? If KPE, flash LF2. The new stock firmwares only have a single .tar file. No modem, csc or any other files needed. And download from here >> http://forum.xda-developers.com/showthread.php?t=1004647/
nbrian2012 said:
First of all post in the general section. Second, read a lot.
Thirdly, which firmware are you at present? If KPE, flash LF2. The new stock firmwares only have a single .tar file. No modem, csc or any other files needed. And download from here >> http://forum.xda-developers.com/showthread.php?t=1004647/
Click to expand...
Click to collapse
i dont know the firmware as the phone is bricked, i managed to get into firmware download mode but it gives me an error after flashing, i flash the pit file and then reset odin and then enter download mode again and select single firmware file and check PDA option but flashing fale.
What file do i download because i downloaded many firmwares gingerbread ones but they all have one single tar file.
Socon off all what box do i need to select if i am flashing a single file , PDA or phone or CSC.
Suhail
suhailpuri said:
i dont know the firmware as the phone is bricked, i managed to get into firmware download mode but it gives me an error after flashing, i flash the pit file and then reset odin and then enter download mode again and select single firmware file and check PDA option but flashing fale.
What file do i download because i downloaded many firmwares gingerbread ones but they all have one single tar file.
Socon off all what box do i need to select if i am flashing a single file , PDA or phone or CSC.
Suhail
Click to expand...
Click to collapse
Download KPE, the files from the link I gave you ^
and follow THIS guide carefully >>>
Misledz said:
2. Run Odin3 v1.83
3. Check Re-Partition, Auto Reboot and F. Reset Time.
4. Click PIT button and select this file: latona_20110114.pit
5. Set it to download mode : Press Volume down + OK first, then hold Power button.
6. Connect USB cable and the program will detect the phone's Com number.
7. Click Start button to download the PIT file to phone.
8. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir]
9. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
11. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
12. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
13: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!]
14. Click Start button to flash these files to phone.
15. Do not touch anything till you see PASS on the program window.
16. Factory reset
17. [To fix issues that pertain] Reflash from steps 9 -15 again, No need of latona at this point.
Click to expand...
Click to collapse
Must you have any issue at any point, reply again.
The SL can never get bricked unless you flash a firmware not compatible with it
Sent from my Galaxy Nexus using Tapatalk 4 Beta
How can i flash a single file .tar.md5 with odin, becuause now all the firmwares come with a single file i.e. .tar.md5 unlike old firmwares have CSC, modem and PDA file
shall i put pit file first and then flash which option needs to be checked ?
This has become really confusing for me now.
Can i also put my phone in download mode and flash via KIES ?
Thanks in advance,
Suhail
suhailpuri said:
i dont know the firmware as the phone is bricked, i managed to get into firmware download mode but it gives me an error after flashing, i flash the pit file and then reset odin and then enter download mode again and select single firmware file and check PDA option but flashing fale.
What file do i download because i downloaded many firmwares gingerbread ones but they all have one single tar file.
Socon off all what box do i need to select if i am flashing a single file , PDA or phone or CSC.
Suhail
Click to expand...
Click to collapse
HELP NEEDED TO FLASH FIRMWARE IN SAMSUNG GALAXY SL GT-I9003
I have downloaded the firmwares suggested by you... Its not clear how to proceed with the flashing of the firmware, as the steps asked to perform by you are contradicting to your previous post -> As there is only only file i.e GT-I9003_XEO_I9003XWLF2_I9003OXXLF1_I9003XXLE4 and rest of the files i.e PHONE file: MODEM_I9003XXKPE_REV_00_CL1041909.tar, BOOTLOADER file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar, CSC file: GT-I9003-CSC-MULTI-OXAKPE.tar are not required. Please be specific what is to be done to complete the flashing procedure.
well i just wanna know how to flash with odin when you have one file for firmware and tutorials show 3 files, but whatever firmwares i download they all have one ta file and no 3 files as suggeted in tutorials.
Suhail
Flash first clean for mandatory starting
On CM10 Alpha 3 and all other basic Froyo, Gingerbread, ICS, JB
- drivers samsung.rar - 5.58 MB
- Open Odin 1.85 only !!!
- KPE FULL (do not forget the PIT) (Froyo only ! no forget bootloader)
reset odin then remove cable and battery after samsung logo
- LF2 (PDA only with Odin)
reset odin then remove cable and battery after second samsung logo
- CF Root LF2 (PDA only with Odin)
I followed all steps, but in STEP 2 when i download the file its iso and not not md5 or tar so i dont know how to proceed and flash it, i tried to mount it , burn it no sucess
Anyways i went to step 3 and flashed again, but phone gets stuck at boot screen samsung logo
Any
UNZIP ?§!
suhailpuri said:
I followed all steps, but in STEP 2 when i download the file its iso and not not md5 or tar so i dont know how to proceed and flash it, i tried to mount it , burn it no sucess
Anyways i went to step 3 and flashed again, but phone gets stuck at boot screen samsung logo
Any
Click to expand...
Click to collapse
Dude, if it's a zip file then extract it & use the file which is extracted.
Good luck!
Sent from my GT-I9003.
LoLaTiOn said:
UNZIP ?§!
Click to expand...
Click to collapse
Hi LoLaTiOn,
I have unzipped the CSROOT file, what I could see was a .img file where as while selecting the file in the ODin 1.85 it demands for a .tar file. Can you please further help in this and pass me the link for the actual file i.e CSROOTXXXXXXXX.tar file in the required format to flash the Android OS.
Rest all the files in the link provided by you are in the required format.
Siddhant Shankpal said:
Dude, if it's a zip file then extract it & use the file which is extracted.
Good luck!
Sent from my GT-I9003.
Click to expand...
Click to collapse
Hi Siddhant,
Anybody in the world knows that we have to unzip a zipped file before using it. The actual problem is that --> After unzipping the file , I see a .img file where as Odin requires a .tar file to flash the Android OS. I tried converting it into a .tar file by using a cygwin terminal but no luck. I also tried searching for the same file in other links (Websites) but still there was no luck.
Can you give a hand to help me out.
suhailpuri said:
Hi Siddhant,
Anybody in the world knows that we have to unzip a zipped file before using it. The actual problem is that --> After unzipping the file , I see a .img file where as Odin requires a .tar file to flash the Android OS. I tried converting it into a .tar file by using a cygwin terminal but no luck. I also tried searching for the same file in other links (Websites) but still there was no luck.
Can you give a hand to help me out.
Click to expand...
Click to collapse
U mentioned "step 2" that means u were stuck in DDLF2 flashing step. But now ur telling "CFROOT LF2" step.
Okay, now in this step u don't need to unzip this file & just flash it from odin as in PDA section.
But I hope ur able to boot into ur phone after flashing DDLF2 firmware.
Good luck!
Sent from my GT-I9003.
Siddhant Shankpal said:
U mentioned "step 2" that means u were stuck in DDLF2 flashing step. But now ur telling "CFROOT LF2" step.
Okay, now in this step u don't need to unzip this file & just flash it from odin as in PDA section.
But I hope ur able to boot into ur phone after flashing DDLF2 firmware.
Good luck!
Sent from my GT-I9003.
Click to expand...
Click to collapse
My bad, I have mentioned it earlier that I have tried flashing the same .img file in the entire process but no luck.
suhailpuri said:
My bad, I have mentioned it earlier that I have tried flashing the same .img file in the entire process but no luck.
Click to expand...
Click to collapse
Download this DDLF2 firmware & extract it. http://forum.xda-developers.com/showthread.php?t=2329200
1. After extracting, switch off your phone & go to download mode.
2. Open odin 1.85 on ur PC & connect ur phone to ur PC. Check, whether it is connected by the yellow signal.
3. First only flash .pit file from the extracted folder. Then remove battery & put it back then again go download mode.
4. Browse & select all respected files from the extracted folder. (Do not include bootloader file if ur coming back to stock from CM 10 based roms.)
5. Click start.
Good luck!
Sent from my GT-I9003.
Odin is the saviour tool for all Samsung devices. The method for flashing by Odin differs from device to device.
This thread will give step by step instructions on how to flash a stock rom from Odin on the GT-I8262/I8260 :
A. Download Odin tools from here Mod edit: Link removed.-Dev-Host links are no longer allowed on XDA.
B. Download the stock rom from*www.samfirmware.com
Setting up Odin :
1. Make sure you have installed the necessary drivers for this device.
The drivers can be installed from within KIES or seperately .
2. Run Odin as administrator.
*3. Setting up the files is divided in two types depending on the firmware type :
a. If the firmware is a multi package file, put the files in the corresponding sections.ie. CSC file in CSC section, PDA file in PDA section.
b. If the firmware is a single package, add the single file in the*PDA section.
4. Now that Odin is setup, put the phone in download mode.
To do that, power off the phone and press 'home+power+volume down' buttons together.
Keep the buttons pressed till Download mide appears.
5. Now that Odin and the phone are setup, connect the phone to the device. Odin will detect the device and show something like 'com port (1)'
6. Flash the device.
7. The flash will take 5 minutes for a full flash on average
8. When the flashing is complete, DO NOT remove the device until Odin shows ' PASS '.
9. The device will reboot. Remove the device, go to recovery mode and do a factory/data reset.
That's it. Happy flashing ..!!
The title of this thread should be
HOW TO FLASH STOCK FIRMWARE
Click to expand...
Click to collapse
Use odin GT-I8262 / I8260
tnx...bro..
qstar.inc said:
The title of this thread should be
Click to expand...
Click to collapse
Yeah ur right xD
Win 7 x86 in Mac OSX Virtual Box VM
Hi, I'm trying to run the Odin with a Windows 7 x86 VM over Mac OSX. The VM has 2GB of RAM and still given to be the message "Program too big to fit in memory.".
I got this message due I'm trying to execute the EXE file by CMD because when I tryed by double clicking a CMD window opened and closed without any action.
Is there a Mac OSX software like Odin?
Thanks.
thanks bro
Hi, i have some doubts about this process:
1) Does flashing stock fw removes TWRP custom recovery? I wannt to put I8260 completely in factory condition...
2) does flashing stock fw increments flash counter?
Thaxnx a lot friends!
vvaibhavv said:
Odin is the saviour tool for all Samsung devices. The method for flashing by Odin differs from device to device.
This thread will give step by step instructions on how to flash a stock rom from Odin on the GT-I8262/I8260 :
A. Download Odin tools from here :* http://d-h.st/hSj
B. Download the stock rom from*www.samfirmware.com
Setting up Odin :
1. Make sure you have installed the necessary drivers for this device.
The drivers can be installed from within KIES or seperately .
2. Run Odin as administrator.
*3. Setting up the files is divided in two types depending on the firmware type :
a. If the firmware is a multi package file, put the files in the corresponding sections.ie. CSC file in CSC section, PDA file in PDA section.
b. If the firmware is a single package, add the single file in the*PDA section.
4. Now that Odin is setup, put the phone in download mode.
To do that, power off the phone and press 'home+power+volume down' buttons together.
Keep the buttons pressed till Download mide appears.
5. Now that Odin and the phone are setup, connect the phone to the device. Odin will detect the device and show something like 'com port (1)'
6. Flash the device.
7. The flash will take 5 minutes for a full flash on average
8. When the flashing is complete, DO NOT remove the device until Odin shows ' PASS '.
9. The device will reboot. Remove the device, go to recovery mode and do a factory/data reset.
That's it. Happy flashing ..!!
Click to expand...
Click to collapse
Hey douche, got a link that doesn't go Str8 to porn?!
I have some questions regarding installing COSMIC ROM on galaxy core duos GT-I8262.
Is it necessary to flash Gapps.zip along with COSMIC. zip?
If Yes, which Gapps should I prefer?
I have Gapps.zip for Marshmallow version, shall I go with it? or else...
Sent from my Sparkle V using Tapatalk
For the past 6 hours I've been trying to unbrick my Samsung Galaxy S6 Edge (G925-W8). I accidentally cleared all the files/ caches with TWRP, now I do not have any OS on it.
Things I've done:
Used Odin to flash a md5 file or a rom I keep getting an error
I'm so lost, I just got the phone yesterday as well too
Do you have twrp? If so, you can sideload a rom. I think you could also mount your sdcard while you're in twrp, and browse it in Windows.
badchip said:
Do you have twrp? If so, you can sideload a rom. I think you could also mount your sdcard while you're in twrp, and browse it in Windows.
Click to expand...
Click to collapse
Yes i still have access to TWRP, but the rest of what you said i have no idea on how to move forward lol
jamescao said:
Yes i still have access to TWRP, but the rest of what you said i have no idea on how to move forward lol
Click to expand...
Click to collapse
Download official firmware from sammobile if u want official, or a custom rom from here on XDA.
Link to YOUR phones official firmware: http://www.sammobile.com/firmwares/database/SM-G925W8/
(Please note that firmware downloads from Sammobile are very limited on speed if you are not a premium member. This download can take a few hours to complete)
If you have an official firmware downloaded:
1. extract the zip file to get your .tar.md5 file
2. turn your phone completely off, then back on in "download mode" you can do this by holding the volume down + home + power keys, then click volume up key to go into download/odin mode.
3. Connect your phone to your computer AFTER phone is in download mode and odin is opened and ready, you will then see it connected.
4. In odin, click on the "PDA" or "AP" (in some versions) button, and find your .tar.md5 file and add it.
5. When this is done make sure only F. Reset Time and Auto Reboot is checked, and most importantly, NOT Re-partition!!
6. Click start and wait for phone to automaticly get the firmware and reboot, when the ID:COM is green, and says completed, you may unplug your phone and set it up.
If you have downloaded a custom ROM from XDA:
1. Connect your phone to the computer.
2. Place the downloaded flashable ROM somewhere on your SD card.
3. Remove phone from PC
4. Boot phone into TWRP (custom recovery)
5. Do a data/factory reset
6. Choose install, find and select your file & click add.
7. Drag pointer to flash selected file.
8. For good spirits, do another wipe of ONLY "dalvic cache & cache" before you reboot phone to start it up.
Hope some of this information can be of any help to you just ask if anything is unclear / bad explained BEFORE you actually do something your unsure of!
Regards
- Renolz
Looks like you tried something without searching first
How did this go? All resolved?
Sent from my SM-G920F using Tapatalk