Database Info

Bricked P350

Hello ,
Ive bricked a LG P350me and need a german stock rom (kzl) endig to flash this with the LG flash tool . Any Idea where i can get one ? I´ve found nothing at the whole internet ...
got one http://csmg.lgmobile.com:9002/swdata/WEBSW/LGP350/ASEABK/V10c_00/V10C_00.kdz from LG server , has anyone the shortcut (ASEABK) for a German Rom ? ... got it ... ADEUAP

think the adminz need to bring a new forum for LG Optimus P350 in here !!

I've bricked my LG P350 too. After i use Call+Vol Up+End, I see this on my screen:
Fastboot mode started:
-- suspend --
-- reset --
-- portchange --
-- reset --
-- portchange --
STALL GET_DESCRIPTION 128 6 1006 0 18
fastboot: processing commands
What shall I do? Can anyone help me? What programs can I use to restore it?

I recieved today the same error-message:
I thought my p350 is bricked, but I tried with the following progs/images about 5 or 6 hours and my phone runs now with the custom rom.
-recovery-RA-pecan-2.2.1-GNM-drap.img.zip
-fastbootflasherV2.zip
-Pecamod_v0.5.zip
-install usb-driver for lg first. Don't run LG-Software
-open fastbootflasher
-connect phone via usb (several tries)
-flash recovery (recovery-RA-pecan-2.2.1-GNM-drap.img)
-reboot phone while holding volume down ,send + end buttons, than it will start in recovery mode.
-Install Pecamod_v0.5.zip from phone sd-card.
Good Luck

p350 bricked
I got similar error when I plugged my phone to my pc. It says:
Fastboot mode started:
-- suspend --
-- reset --
-- portchange --
-- reset --
-- portchange -
When not plugged in:
Fastboot mode started:
udc-start()
This is the only forum that tackles this subject/ and was trying to do these steps:
-install usb-driver for lg first. Don't run LG-Software
-open fastbootflasher
-connect phone via usb (several tries)
-flash recovery (recovery-RA-pecan-2.2.1-GNM-drap.img)
-reboot phone while holding volume down ,send + end buttons, than it will start in recovery mode.
-Install Pecamod_v0.5.zip from phone sd-card.
downloaded all of the files from net but unfortunately my pc doesnt detect my p350. I think I have downloaded all of the usb drivers available for my lg phone still no go/
Hey schweitzi67, can you give me a step by step instructions on how you did your recovery? I'd really appreciate it if you will. Thanks in advance.

first of all, since you all can boot into fastboot, NONE of you guys are bricked
and second, heres how to fix your fastboot (now before you continue, remember that you need to replace the lg optimus one files in this link with the files that suit your phone, which is to say that you need to find the kdz file for your phone before you begin this):
http://forum.xda-developers.com/showthread.php?t=1088046
http://forum.xda-developers.com/showthread.php?t=1015332
read through those two links carefully and make sure you know what you are doing because your phone can get bricked if you do something wrong. if you have the slightest doubt go research more

Hi. I tried doing all instructions from the first thread you posted. When everything is ready, plugged my p350, went to command prompt and typed "fastboot erase recovery" but it said "<waiting for device>" I have downloaded lgunited mobile driver from lgsetup (B2CappSetup). What do you think the problem is? Thanks!

joolsthebear said:
Hello ,
Ive bricked a LG P350me and need a german stock rom (kzl) endig to flash this with the LG flash tool . Any Idea where i can get one ? I´ve found nothing at the whole internet ...
got one from LG server , has anyone the shortcut (ASEABK) for a German Rom ? ... got it ... ADEUAP
Click to expand...
Click to collapse
Hey have you found a german rom? I am still searching, but i can´t find any Firmware with ADEUAP regioncode.
Maybe someone know where to get the firmware.
Nice Day

Be careful... I installed kdz wrong and now my phone, it does not work
I heard that can be easily solved if you start downloadmod but I do not know how to do it .... help

sweetnsour said:
first of all, since you all can boot into fastboot, NONE of you guys are bricked
and second, heres how to fix your fastboot (now before you continue, remember that you need to replace the lg optimus one files in this link with the files that suit your phone, which is to say that you need to find the kdz file for your phone before you begin this):
http://forum.xda-developers.com/showthread.php?t=1088046
http://forum.xda-developers.com/showthread.php?t=1015332
read through those two links carefully and make sure you know what you are doing because your phone can get bricked if you do something wrong. if you have the slightest doubt go research more
Click to expand...
Click to collapse
Thank you!! Your first link whas the solution for my problem, it wasn't easy for a noob like me, but it's doable if you follow those instructions very carefully
I'm so happy! thanks again.

my P350 is just dead
Hi Guys,
Have the very same problem here. Tried to flash new ROM, phone entered in yellow emergency screen, got an failed error from KDZ and now the phone is dead.
I can not seem to start it, tried any keys combinations but the phone seems to not respond at all.
If i at least could get into an emergency screen or something but...nothing...black screen and no hearth beat
Is this really the end of it?
Much appreciated for a solution here.

Phone doesnt turn off!

So my phone got bricked ! It had the fastboot error , after i did the recovery crap on cmd it only showed lg startup logo , but i was able to go to emergency mode ! Now my phone wont turn on at all . I followed these instructions : http://forum.xda-developers.com/showthread.php?t=875881
Please explain me , is there a way to fix this ?! Will i be able to exchange for a new phone if i still have the guarantee for my phone ? What should i do i am pretty desperate i don't want my mom to kill me lol .

PacManOG said:
So my phone got bricked ! It had the fastboot error , after i did the recovery crap on cmd it only showed lg startup logo , but i was able to go to emergency mode ! Now my phone wont turn on at all . I followed these instructions : http://forum.xda-developers.com/showthread.php?t=875881
Please explain me , is there a way to fix this ?! Will i be able to exchange for a new phone if i still have the guarantee for my phone ? What should i do i am pretty desperate i don't want my mom to kill me lol .
Click to expand...
Click to collapse
P.S
I mean doesnt turn ON !

When you KDZ... ALWAYS " DISABLE " LG USB MODEM in Device Manager.
See if your phone enters emergency mode. Search this forum.
If its under warranty.. they might replace it for free but dont tell them you rooted your phone or anything!!

rr0yy said:
When you KDZ... ALWAYS " DISABLE " LG USB MODEM in Device Manager.
See if your phone enters emergency mode. Search this forum.
If its under warranty.. they might replace it for free but dont tell them you rooted your phone or anything!!
Click to expand...
Click to collapse
I did disable LG USB Modem . I know what is emergency mode i mean i cant do ANYTHING , its like put it to a pc or a charger take battery out try the same put the batery in the same , nothing . It simply doesnt want to turn on
Edit :
Ok so i found out .
Bricked means dead = i have to get a new phone , had the phone for only 2-3 months , so i have the guarantee , hope they will exchange it for a new one or let them fix it by replacing the circuit board or something

Here
If its not entering Emergency.. there is no other way to recover. Go to Service Centre!!

[Q] LG Optimus One bricked after failed reflash

Hello XDA-Developers
Before I am writing this, I want to say that I am relative jung and my English is not the best.
1 Year ago I rooted my phone, it worked great and so on.
After a half yeah I updatet the firmware on 2.3.3, but the root was still there.
No Problem, yesterday I wanted to install the cyagon-mod and I wanted first to flashback to the old Baseband @ 2.2.2.
I use the KDZ Updater and try to flashback to 2.2.2, but I followed the tutorials here, but at the time of flashing I
got a problem! The KDZ Updater sayed there was a fail. I attached the log. (Maybe the kdz file was damaged?)
I pulled it out and I took out the battery.
......
Now I think my LG Optimus one is bricked.
I if I try to start the phone nothing happend, if I try to get to the recovery mode it won´t give me a signal.
If I plug it into my PC with LG united Mobile Drivers installed it won´t get to the recovery mode.
I saw that I have a C++ runtime enviroment is that a Problem?
Is there probaly a method to repair the phone? Or can someone at my local mobilephone shop repair my mobile
Greetz

Bladgen said:
Hello XDA-Developers
Before I am writing this, I want to say that I am relative jung and my English is not the best.
1 Year ago I rooted my phone, it worked great and so on.
After a half yeah I updatet the firmware on 2.3.3, but the root was still there.
No Problem, yesterday I wanted to install the cyagon-mod and I wanted first to flashback to the old Baseband @ 2.2.2.
I use the KDZ Updater and try to flashback to 2.2.2, but I followed the tutorials here, but at the time of flashing I
got a problem! The KDZ Updater sayed there was a fail. I attached the log. (Maybe the kdz file was damaged?)
I pulled it out and I took out the battery.
......
Now I think my LG Optimus one is bricked.
I if I try to start the phone nothing happend, if I try to get to the recovery mode it won´t give me a signal.
If I plug it into my PC with LG united Mobile Drivers installed it won´t get to the recovery mode.
I saw that I have a C++ runtime enviroment is that a Problem?
Is there probaly a method to repair the phone? Or can someone at my local mobilephone shop repair my mobile
Greetz
Click to expand...
Click to collapse
if der is no light coming out than its hard bricked if you can go to emergency mode(google it) then u r lucky u can flash ur file again but this time use lgmdp method
or use kdz with precaution

androidisfuture said:
if der is no light coming out than its hard bricked if you can go to emergency mode(google it) then u r lucky u can flash ur file again but this time use lgmdp method
or use kdz with precaution
Click to expand...
Click to collapse
Thank you for your help, what do you mean with no light coming out I don´t understand you.
Do you think a member of a company which repair mobile phones can repair the phone?
Greetz

Bladgen said:
Thank you for your help, what do you mean with no light coming out I don´t understand you.
Do you think a member of a company which repair mobile phones can repair the phone?
Greetz
Click to expand...
Click to collapse
by power on is lg logo comes
if not something or the other happens like emergency mode download mode if not
then its hard bricked
and i think u have your warranty over so just buy a new phone the company will charge u too much if u are hard bricked

No.. phone repair stores cant help you.
You have to do it yourself or take it to LG service centre.
First press Back + Vol up + Power button.. see if you get yellow emergency mode.
If no your phone is hard bricked.. no way to repair.. but stil search the forum.. see if you can make it work.
See if this helps
If emergency mode is working.. then you can easily recover your phone.
Here
Flash the recovery and then flash any rom of your choice!!

rr0yy said:
No.. phone repair stores cant help you.
You have to do it yourself or take it to LG service centre.
First press Back + Vol up + Power button.. see if you get yellow emergency mode.
If no your phone is hard bricked.. no way to repair.. but stil search the forum.. see if you can make it work.
See if this helps
If emergency mode is working.. then you can easily recover your phone.
Here
Flash the recovery and then flash any rom of your choice!!
Click to expand...
Click to collapse
i have said the same thing man

[How TO] Unbrick, hard bricked LG Optimus One (P500)

I was using
Device: LG Optimus One P500
Recovery: ClockworkMod 5.0.2.7
Kernel version: 2.6.35.10
Android version: 4.2.1
Current ROM: GenetICS 9.1.7
Then I downloaded another custom ROM [4.2.1]PACman 19.9.0 [PA][AOKP][CM](seems to be deleted now). Stating thats its some updated version of previous ROM.
Downloaded through XDA app and then opened it directly with ROM Manager to install it.
But unfortunately something went wrong and my phone got stuck on boot logo i.e. LG. :silly:
Then I tried to repair it with KDZ updater using V20c-00 firmware. Everything worked fine. I rooted it through SuperOne click and installed CWM recovery through ROM Manager. :victory:
Till then everything was looking under control.
After that I tried to flash another ROM through CWM Recovery, but again i got stuck on Boot Logo. I tried to repair it once again with KDZ updater as I did it previously, but everytime KDZ updater showed error.
Now my phone is not even responding to anything means not with hard keys combos or something. :crying:
I am not able to find any solution for this, even I searched it a lot.
Please please help me.
Edit: If only LG can help me now, can anyone tell me how much it will cost?

Unfortunately, if you removed the battery after KDZ gives out an error, you have hard-bricked your phone. Only LG can help you now

There is an emergency mode you can attempt, as long as you have the software on your computer to flash factory settings on to your phone.
To access emergency mode, do the following:
1) Take out the battery
2) Have a usb cable already connected to the computer.
3) Hold the power button + volume up + back button AND then connect the usb while holding those buttons
Yellow screen will appear with the words emergency mode in the middle.
At this point, do some forum searching, find some kind of stock image file and LG program to flash stock system on to the phone.
*there is also a forum post somewhere here that I learnt this stuff off of...see if you can find it

a_loo said:
There is an emergency mode you can attempt, as long as you have the software on your computer to flash factory settings on to your phone.
To access emergency mode, do the following:
1) Take out the battery
2) Have a usb cable already connected to the computer.
3) Hold the power button + volume up + back button AND then connect the usb while holding those buttons
Yellow screen will appear with the words emergency mode in the middle.
At this point, do some forum searching, find some kind of stock image file and LG program to flash stock system on to the phone.
*there is also a forum post somewhere here that I learnt this stuff off of...see if you can find it
Click to expand...
Click to collapse
I have not had any luck with KDZ or LGMDP with a device stuck in Emergency Mode. I have two P506's that are stuck in Emergency Mode, thanks to KDZ. I have tried every fix I can find here and on several other forums with no luck. I don't want to discourage you, but don't get your hopes up either.
I know this is OT, but...
This is the kind of stuff that we like to see from New Members here at XDA. This is the right way to get your 10 posts. Keep it up

shinobisoft said:
I have not had any luck with KDZ or LGMDP with a device stuck in Emergency Mode. I have two P506's that are stuck in Emergency Mode, thanks to KDZ. I have tried every fix I can find here and on several other forums with no luck. I don't want to discourage you, but don't get your hopes up either.
I know this is OT, but...
This is the kind of stuff that we like to see from New Members here at XDA. This is the right way to get your 10 posts. Keep it up
Click to expand...
Click to collapse
I remember being successful with the LGMDP in emergency Mode with the P500, even though the stock rom that i used didnt quite work with the phone it got me past the boot logo and gave me access back into my recovery. Once you can at least get into the recovery you are golden (for the most part).
OT:
Thanks shinobi. I've been lurking xda for a while now since i got the p500, just recently i really wanted to post in rashed's thread for issues/bugs i found with the cm10.1 rom

a_loo said:
There is an emergency mode you can attempt, as long as you have the software on your computer to flash factory settings on to your phone.
To access emergency mode, do the following:
1) Take out the battery
2) Have a usb cable already connected to the computer.
3) Hold the power button + volume up + back button AND then connect the usb while holding those buttons
Yellow screen will appear with the words emergency mode in the middle.
At this point, do some forum searching, find some kind of stock image file and LG program to flash stock system on to the phone.
*there is also a forum post somewhere here that I learnt this stuff off of...see if you can find it
Click to expand...
Click to collapse
shinobisoft said:
I have not had any luck with KDZ or LGMDP with a device stuck in Emergency Mode. I have two P506's that are stuck in Emergency Mode, thanks to KDZ. I have tried every fix I can find here and on several other forums with no luck. I don't want to discourage you, but don't get your hopes up either.
I know this is OT, but...
This is the kind of stuff that we like to see from New Members here at XDA. This is the right way to get your 10 posts. Keep it up
Click to expand...
Click to collapse
a_loo said:
I remember being successful with the LGMDP in emergency Mode with the P500, even though the stock rom that i used didnt quite work with the phone it got me past the boot logo and gave me access back into my recovery. Once you can at least get into the recovery you are golden (for the most part).
OT:
Thanks shinobi. I've been lurking xda for a while now since i got the p500, just recently i really wanted to post in rashed's thread for issues/bugs i found with the cm10.1 rom
Click to expand...
Click to collapse
No luck to me guys. As I already mentioned that there is no response from phone, not even emergency mode.
Now I tried with even JTAG still no luck.
Went to LG day before yesterday as that was the only hope. But unfortunately my phone is out of warranty and the cost of motherboard is almost equal to the cost of phone itself.
So, that means I have no other option besides keeping it with me as a precious piece of brick.
Thanks to KDZ_Updater.

rishabhgangwar said:
No luck to me guys. As I already mentioned that there is no response from phone, not even emergency mode.
Now I tried with even JTAG still no luck.
Went to LG day before yesterday as that was the only hope. But unfortunately my phone is out of warranty and the cost of motherboard is almost equal to the cost of phone itself.
So, that means I have no other option besides keeping it with me as a precious piece of brick.
Thanks to KDZ_Updater.
Click to expand...
Click to collapse
Now my Phone has the same issue like you'r one. :crying:
Tried every hard button combo. no luck. Now woried because my phone also out of warranty.
Have you repaired your one?
How much cost you new motherboard buddy?

warlock911 said:
Now my Phone has the same issue like you'r one. :crying:
Tried every hard button combo. no luck. Now woried because my phone also out of warranty.
Have you repaired your one?
How much cost you new motherboard buddy?
Click to expand...
Click to collapse
Cost of motherboard from LG was 8800/- Indian Rupees. And the total cost of phone was 9999/- Indian Rupees.
But I got it repaired in 1800/- Indian Rupees with JTAG. Thanks to a local mobile repair shop.
But I am afraid that this service may not be available in your country.

I am also from India buddy. But I don't think so I could fund jtag in my city.
What is your location?

warlock911 said:
I am also from India buddy. But I don't think so I could fund jtag in my city.
What is your location?
Click to expand...
Click to collapse
I am living in delhi. What is your location?

I am from gwalior.
How much time taken by a jtag technician / shop to repair your mobile.????

warlock911 said:
I am from gwalior.
How much time taken by a jtag technician / shop to repair your mobile.????
Click to expand...
Click to collapse
It took around 1 hour.

Hmm
One hour... But 800 buks ... Let Mr see if it is available in my city.
Thanks

lg phoenix p505 softbrick fix
had an lg phoenix that kept giving status 7 errors when I tried to flash in recovery, failures in fastboot, and normal boot just went to black screen
Then I found "how-to-fix-lg-phoenix-fastboot-issues" a page that has working KDZ instructions (after a fashion), now it boots to an ugly fuzzy blue bad driver ancient version of android, but hey, it's alive again!
I would post the link, but spam filter prevents it. it was over at lg-phones dot org.

help
I am having same problem.
Can you tell me contact of mobile of repair shop
rishabhgangwar said:
Cost of motherboard from LG was 8800/- Indian Rupees. And the total cost of phone was 9999/- Indian Rupees.
But I got it repaired in 1800/- Indian Rupees with JTAG. Thanks to a local mobile repair shop.
But I am afraid that this service may not be available in your country.
Click to expand...
Click to collapse

search web for OCTOPUSBOX or MEDUSABOX, this are sites for JTAG sales but they offer software for free, maybe you will have luck
or bring it to repair shop, it will cost you around 20$

Could you pls tell me if this procedure helps in my situation?
a_loo said:
There is an emergency mode you can attempt, as long as you have the software on your computer to flash factory settings on to your phone.
To access emergency mode, do the following:
1) Take out the battery
2) Have a usb cable already connected to the computer.
3) Hold the power button + volume up + back button AND then connect the usb while holding those buttons
Yellow screen will appear with the words emergency mode in the middle.
At this point, do some forum searching, find some kind of stock image file and LG program to flash stock system on to the phone.
*there is also a forum post somewhere here that I learnt this stuff off of...see if you can find it
Click to expand...
Click to collapse
Hi a_loo!
I Have a LG P500 2.3.3 V20e.
I rooted it today without any problem. Loaded ROM manager, flashed ClockworkMod recovery.
Then I downloaded from Cyanogen cm-7.2.0-p500.zip and placed it on the SD card.
And from ROM manager I did an "install ROM from SD card."
It worked for a while the it froze with a cyanogenmod 7 image. None of the controls & buttons and working.
I'm rather new and trying not to panic.
I'd really appreciate your assistance.

kocag said:
Hi a_loo!
I Have a LG P500 2.3.3 V20e.
I rooted it today without any problem. Loaded ROM manager, flashed ClockworkMod recovery.
Then I downloaded from Cyanogen cm-7.2.0-p500.zip and placed it on the SD card.
And from ROM manager I did an "install ROM from SD card."
It worked for a while the it froze with a cyanogenmod 7 image. None of the controls & buttons and working.
I'm rather new and trying not to panic.
I'd really appreciate your assistance.
Click to expand...
Click to collapse
Thanks to the post I was able to boot into recovery, then reload my old ROM from backup. Issue is closed.

Can u Plz upload the stock rom for lg in Kdz format
Sent from my GT-I9082 using Tapatalk 2
---------- Post added at 02:35 PM ---------- Previous post was at 02:29 PM ----------
Can u Plz upload lg stock rom in Kdz format
Sent from my GT-I9082 using Tapatalk 2

Bricked Lg P500
I hard bricked my LG P500 today. It seems there is no hope... No life at all. Oh well... Life sucks I'm in South Africa and don't want to spend money on older phone. I probably did something wrong with LG KDZ, trying to flash stock ROM.

[Completed] Verizon LG G2 bricked after OTA kitkat update

My G2 has been bricked since April and have had no success to revive my phone.
The phone goes to a blank screen after the LG logos shows up. Also I can't get into download or recovery mode. Whenever I connect the phone to my computer a bunch of drivers start popping up and that's as far as I can get.
Please can somebody help me out!!!!!

Caj31 said:
My G2 has been bricked since April and have had no success to revive my phone.
The phone goes to a blank screen after the LG logos shows up. Also I can't get into download or recovery mode. Whenever I connect the phone to my computer a bunch of drivers start popping up and that's as far as I can get.
Please can somebody help me out!!!!!
Click to expand...
Click to collapse
Hi!
I found a similar issue....perhaps it can help?
Otherwise without being able to get into download or recovery modes is not good. Service may be the only other option.
http://forum.xda-developers.com/showthread.php?t=2654355
Good luck!