I have a 2011 Jeep Grand Chreokee. When I first got the phone, it paired fine and I was able to make and receive calls through the BT. I had this setup for about 1-2 days. I then rooted the phone with the stock ROM only removing bloat ware...now I cannot connect via bluetooth back to the car. It seems to connect then disconnect me right away. Ideas?
I know this seems obvious but have you tried unpairing and repairing the phone to the car? Sometimes bluetooth can get fidgety and most of the time it requires you to repair the device. In my experience that generally solves the issues I have had with bluetooth.
Any time I have factory restored my phone I have had to repair it to any Bluetooth devices it was once connected to. Not sure if the Bluetooth address changes for the phone or not on a reset or ROM change, but it seems to be the case. My Infiniti G37s has Bluetooth and I experienced the same issue as you, pair it again and see if that helps.
Thanks for replies...I tried to repair about 6 different times...same result. It seem that the phone and audio connections both connect for about 2 seconds, then the phone disconnects.
Funny, I wanted to try this but kept forgetting. So I just went down to my garage and tried it, and it paired successfully on the first try. Tried making a call via number/phonebook and it all worked.
I'm rooted running Das BAMF 1.3, and paired it with a '11 Sonata Limited.
So I got it working...but without the phone book downloaded. The issue is in fact when it tries to download the phone book. Need to get another phone loaded up with my contacts and do a sync to get phone book loaded to car.
DieselvRR said:
So I got it working...but without the phone book downloaded. The issue is in fact when it tries to download the phone book. Need to get another phone loaded up with my contacts and do a sync to get phone book loaded to car.
Click to expand...
Click to collapse
Did you do anything to get it working?
When the device asked me to allow connection to download the phone book, I declined, only then would it pair properly.
I think I figured it out, I have the Infiniti G37, when I rooted & re-paired the Bluetooth, somehow I ignored the question when it popped up asking to "allow" or "deny" the connection.
Yesterday during the whole 4G fiasco, I reflashed & had to re do everything this morning, when I paired my BT, it asked me whether to allow & this time I clicked allow & my BT connects & stays connected fine now.
My question is, is there a way to delete the BT pairing on the phone without having to completely wipe the phone with a reflash?
ruddogg said:
I think I figured it out, I have the Infiniti G37, when I rooted & re-paired the Bluetooth, somehow I ignored the question when it popped up asking to "allow" or "deny" the connection.
Yesterday during the whole 4G fiasco, I reflashed & had to re do everything this morning, when I paired my BT, it asked me whether to allow & this time I clicked allow & my BT connects & stays connected fine now.
My question is, is there a way to delete the BT pairing on the phone without having to completely wipe the phone with a reflash?
Click to expand...
Click to collapse
nevermind, I just found the answer
http://support.vzw.com/clc/devices/knowledge_base.html?id=39262
just hold down "paired"
I believe the issue is just with the MyGig radio on the Chrysler products. I have a SRT8 Magnum with the MyGig and allowing it to download the address book "Breaks" the B.T. connection. I don't know what the issue is? Perhaps too much information being sent to the MyGig and it "locks up"?
I also have a Ford Focus for a daily driver and allowing it to download the Address Book over the phone has no such issue.
DieselvRR said:
When the device asked me to allow connection to download the phone book, I declined, only then would it pair properly.
Click to expand...
Click to collapse
It does it on my aftermarket Kenwood double-din unit, too. I've seen it happen on several Ford units too.
usafle said:
I believe the issue is just with the MyGig radio on the Chrysler products. I have a SRT8 Magnum with the MyGig and allowing it to download the address book "Breaks" the B.T. connection. I don't know what the issue is? Perhaps too much information being sent to the MyGig and it "locks up"?
I also have a Ford Focus for a daily driver and allowing it to download the Address Book over the phone has no such issue.
Click to expand...
Click to collapse
I updated my 430N radio with the latest firmware update and phone book downloaded and BT is working without getting disconnected.
Thanks
Thanks for that info. Although I can't do it as I have the "MyGig" retro-fitted into my 07 SRT. So, if I apply the "official update" I will lose GPS time and a bunch of other things.
But, nice to know it works.
DieselvRR said:
I updated my 430N radio with the latest firmware update and phone book downloaded and BT is working without getting disconnected.
Thanks
Click to expand...
Click to collapse
I successfully paired my 16gb motoactv with my laptops Bluetooth connection. I was then able to play music from the device through my laptop. The pairing and connection was simple and strait forward . I accidentally hit 'forget' on my motoactv device and I went to pair again so I removed the device from my laptop and went on to pair. This time around the two devices will not discover one another.
Each device, my laptop and motoactv will discover and pair with other devices (headsets, car head unit) just not with eachother. I tried all i could think which was uninstall all bluetooth drivers and bluetooth software and did a re-install. I rooted and rebooted in recovery. Did a full wipe and then installed a downloaded and installed 16gb stock rom and still it just will not discover. It is acting like it is still paired therefore not discovering one another. I feel the issue is more with my computer. I feel like the computer did not 100% get rid of the pairing information but i am not sure. I base that on the fact I did a complete wipe of the data and installed a fresh stock rom. How would I be able to re-pair these two or make sure the pairing was completly uninstalled on my laptop. Hp Pavillion dv6 win7
I dont get how this device can pair without a hitch the first time around and the second time around it wont even discover one another.
More small details, I was in the process of rooting the device - would that affect bluetooth discovery. Something I could figure out quickly but I doubt it. The motoactv also does not discover on my bluetooth enabled ipad. Not sure if it could or should discover. At this point im just doing trial and error to really figure out this odd problem,
Hi, you should try and look if your laptop has "Enable this device to be discovered" or something like that in the bluetooth options. Basically, you need to make your laptop discoverable. Then go to phone setup on motoactv and set it up. After that you should be able to see your laptop in the wireless menu in the motoactv and connect to it. I also use my motoactv to play music through my laptop speakers.
Hi. In the last couple of days, I used "Bluetooth Audio Receiver" from the Microsoft store to be able to play back music from my S20 FE android 11 device at work. I often step away from my work desk with my phone in my pocket, but yesterday I wasn't able to reconnect my phone via Bluetooth when I came back. Since then I can't connect to my work and my personal PC anymore, even tho I didn't even connect to my personal PC for a while.
I'm able to unpair and pair with said Windows 10 machines, but as soon as I tap the entry in the Bluetooth menu, it says "couldn't connect". I already tried to use the reset for wifi/Mobil/Bluetooth within the android setting, but it didn't change anything.
Restarted my phone and both PCs multiple times. It feels like something in my phone hang itself. I'm still able to send files from my PC to my phone and vice versa. I'm still able to fully use my smartwatch and Bluetooth headset.
Is there anything I can do? Any ideas?
PS: My phone is rooted.
Edit1: I just deleted cache and data of the Bluetooth app and did another reset of my network settings. I now can't pair with Windows 10 anymore. It says "couldn't connect" after the pairing dialog. My Win10 Device recognizes my Android device as paired. Which means I can't even send or receive files at my phone from my Windows 10 devices.
Edit2: My headset was still paired. Is there a way to reset saved pairing and data related to that?
Edit3: I don't know why I couldn't pair with my Windows device anymore, but it works again (Didn't do anything). Still can't connect to it, but can send files again.
TLDR:
Android 11 S20 FE can't connect to multiple Windows devices anymore with the massage: "can't connect".
UnPairing and pairing again won't help
Restarting effected devices won't help.
Resetting network settings won't help.
Nobody has an idea what it could have triggered it or what I could try to do?
Any idea is much appreciated.
I have been experiencing issues connecting to devices over Bluetooth. Sometimes it just works, other times it doesn't work at all, and some times it kinda works but not right.
All of these issues are resolved by restarting the phone, but that isn't a solution because the issue comes back.
3 Devices I have been having issues with
1. S Pen - Sometimes it won't connect to the phone, I get an "S-Pen Missing" message and it will not connect. If I t ry to connect to it manually via nRF Connect (The Nordic Semiconductors Bluetooth App) it tells me that the BLE device has a GATT error. It happens semi-randomly but I can always make it happen by doing #2
2. Car Stereo - This is the weird one, it will connect and play music, but it will not do "calls" if I connect to Discord it won't recognise the car as a Bluetooth device it can route to.
3. Raspberry Pi - This one it appears it will connect to ONCE, and then after a disconnect it will not connect again.
Again, each of these can be fixed by restarting the device, but they happen again after a while. The pen & RPi use BLE, I don't know what the car uses for calls.
Turn off global power management completely in Device Care.
Network reset, reboot and clear system cache from the boot menu.
Ok, I've done a network reset, and cleared the cache partition. I checked Device Care for something like global power management, and I couldn't find anything. Most of the pwm settings are off except the "optomise daily" setting.
I'll let you know later if I have the same issue again.
These, this is a N10+ running on Pie.
To check if you have disabled global power go to Developer options>standby apps, all buckets should show as active otherwise power management is enable.
KindarConrath said:
I have been experiencing issues connecting to devices over Bluetooth. Sometimes it just works, other times it doesn't work at all, and some times it kinda works but not right.
All of these issues are resolved by restarting the phone, but that isn't a solution because the issue comes back.
3 Devices I have been having issues with
1. S Pen - Sometimes it won't connect to the phone, I get an "S-Pen Missing" message and it will not connect. If I t ry to connect to it manually via nRF Connect (The Nordic Semiconductors Bluetooth App) it tells me that the BLE device has a GATT error. It happens semi-randomly but I can always make it happen by doing #2
2. Car Stereo - This is the weird one, it will connect and play music, but it will not do "calls" if I connect to Discord it won't recognise the car as a Bluetooth device it can route to.
3. Raspberry Pi - This one it appears it will connect to ONCE, and then after a disconnect it will not connect again.
Again, each of these can be fixed by restarting the device, but they happen again after a while. The pen & RPi use BLE, I don't know what the car uses for calls.
Click to expand...
Click to collapse
Are those the only three devices you connect via BT? What other apps do you use that need to use BT (i.e. Galaxy Wear, Apple Music, etc.).
You mentioned "Nordic Semiconductors Bluetooth App." I looked it up. Why do you need a third party generic BLE connecting app? It seems to me that could be the problem. You shouldn't need a third-party app to connect your BLE devices. The S22U's native pairing will work with any BT device that adheres to BT standards.
Try uninstalling the nRF Connect app and see what happens.
The only other Bluetooth devices I have are other in-house hardware, running on SiliconLabs BGM13P chips or NRF52840 chips...
The NRF app isn't a replacement for your bluetooth pairing app, its a debugging app... it can connect to BLE devices and show their GATT profiles, update devices that have Nordic's OTA update code and copy a devices GATT profile to act as a BLE Server.
We use it for testing and debugging.
KindarConrath said:
The only other Bluetooth devices I have are other in-house hardware, running on SiliconLabs BGM13P chips or NRF52840 chips...
The NRF app isn't a replacement for your bluetooth pairing app, its a debugging app... it can connect to BLE devices and show their GATT profiles, update devices that have Nordic's OTA update code and copy a devices GATT profile to act as a BLE Server.
We use it for testing and debugging.
Click to expand...
Click to collapse
Ok. I recommend uninstalling nRF Connect anyway. If anything, to rule out the app. How old is your car and the Raspberry Pi? Even though BT 5.2 is backwards compatible, sometimes older BT devices won't work with newer devices. That doesn't account for the S Pen issue though.
I uninstalled nRF connect, and changed all the settings you both recommended. Exactly the same behaviour when I went to leave work. My car stereo would do music but not calls, then when I restarted my phone, it worked. Then when I got home, my S Pen would not connect to my phone, then I restarted my phone and it worked.
Its not a problem of not being compatible, its a problem of something stops working.
Please also note that these devices worked fine together in the past. I am concered that it is either a change made by an update or a Bluetooth chip that is faulty....
OP- Have you debloated at all and if so maybe you've removed something relevant that might be causing these issues?
No, stock image, no OS modification beyond the things that Samsung offers (GoodLock and Stock customisation)
I have our in-house apps for interacting with our equipment (over Bluetooth) installed, but #1 they shouldn't affect anything if they are not open and #2 they don't do this to ANY of our other test equipment.
I would just like to say, that I appreciate the assistance that you are all offering! I have used many forums over the years when looking for support on things and I rarely find a place that is more ready to try and help than XDA forums!
KindarConrath said:
I have been experiencing issues connecting to devices over Bluetooth. Sometimes it just works, other times it doesn't work at all, and some times it kinda works but not right.
All of these issues are resolved by restarting the phone, but that isn't a solution because the issue comes back.
3 Devices I have been having issues with
1. S Pen - Sometimes it won't connect to the phone, I get an "S-Pen Missing" message and it will not connect. If I t ry to connect to it manually via nRF Connect (The Nordic Semiconductors Bluetooth App) it tells me that the BLE device has a GATT error. It happens semi-randomly but I can always make it happen by doing #2
2. Car Stereo - This is the weird one, it will connect and play music, but it will not do "calls" if I connect to Discord it won't recognise the car as a Bluetooth device it can route to.
3. Raspberry Pi - This one it appears it will connect to ONCE, and then after a disconnect it will not connect again.
Again, each of these can be fixed by restarting the device, but they happen again after a while. The pen & RPi use BLE, I don't know what the car uses for calls.
Click to expand...
Click to collapse
I've seen the issue of the spen disconnecting but only a couple of times and the issue worked itself out within a couple of minutes with me not having to do anything.
I've also have had a couple of wonky issues when connecting a new Samsung phone to my car. I've narrowed down my issue to the fact that when I transfer my data & settings via Samsung smart switch, it includes the details of my Bluetooth pairings. To fix it, I have to go in and delete my Bluetooth phone settings from the car and from my phone and re-pair them.
Rubby1025 said:
I've seen the issue of the spen disconnecting but only a couple of times and the issue worked itself out within a couple of minutes with me not having to do anything.
I've also have had a couple of wonky issues when connecting a new Samsung phone to my car. I've narrowed down my issue to the fact that when I transfer my data & settings via Samsung smart switch, it includes the details of my Bluetooth pairings. To fix it, I have to go in and delete my Bluetooth phone settings from the car and from my phone and re-pair them.
Click to expand...
Click to collapse
As cool as I think Smart-Switch is as a program, I actually never use it when moving from one phone to another. The junk that Google drags with me from one phone to the next is already too much, I like to use a new device as a chance to do some housecleaning. So no old-data oddities here.
KindarConrath said:
I uninstalled nRF connect, and changed all the settings you both recommended. Exactly the same behaviour when I went to leave work. My car stereo would do music but not calls, then when I restarted my phone, it worked. Then when I got home, my S Pen would not connect to my phone, then I restarted my phone and it worked.
Its not a problem of not being compatible, its a problem of something stops working.
Please also note that these devices worked fine together in the past. I am concered that it is either a change made by an update or a Bluetooth chip that is faulty....
Click to expand...
Click to collapse
Hmmm.. Ok. You're probably right about the suspect causes. I know there is a code you can dial to get into diagnostic mode, I just don't know what it is.
The only other option you can try (as a last resort) is to factory reset it. If it is update caused, a factory reset MAY fix it. If you take it to a service center, send it in for repairs, or do a warranty replacement, they're going to factory reset it, or have you reset it.
have you tried running diagnostics in device care ?
or check with this dc
android
Bluetooth test*#*#232331#*#*
samsung
Bluetooth Test Mode*#232331#
I still haven't done a factory reset, but I continue to have the issue.
I have run the BT Test in device care, it always reports good.
I tried the codes, neither of them work as the first one is for vanilla android and the second is for older versions of Samsung firmware.
I've tried completely unpairing from the car radio and re-pairing, disconnecting and connecting from the other device to no avail.
KindarConrath said:
I still haven't done a factory reset, but I continue to have the issue.
I have run the BT Test in device care, it always reports good.
I tried the codes, neither of them work as the first one is for vanilla android and the second is for older versions of Samsung firmware.
I've tried completely unpairing from the car radio and re-pairing, disconnecting and connecting from the other device to no avail.
Click to expand...
Click to collapse
I'm not entirely sold on the idea that it is a hardware fault. It could be a hardware limitation; meaning you cannot connect to more than a certain number of devices simultaneously. I don't know how many BT devices you can connect to at once. I know at least two simultaneous connections (I've only had two simultaneous connections at a time).
You said you have other BT devices in your house other than those three your having issues with. How many are there? How many are you connected to at any given moment?
Is it possible that you have too many simultaneous connections?
When you try to connect to your car.. Did you check under BT connection (your vehicle) to make sure both audio and calls are checked..
doubledragon5 said:
When you try to connect to your car.. Did you check under BT connection (your vehicle) to make sure both audio and calls are checked..
Click to expand...
Click to collapse
Yes, and I've disconnected, reconnected and even unpaired and re-paired the phone to the car.
gernerttl said:
I'm not entirely sold on the idea that it is a hardware fault. It could be a hardware limitation; meaning you cannot connect to more than a certain number of devices simultaneously. I don't know how many BT devices you can connect to at once. I know at least two simultaneous connections (I've only had two simultaneous connections at a time).
You said you have other BT devices in your house other than those three your having issues with. How many are there? How many are you connected to at any given moment?
Is it possible that you have too many simultaneous connections?
Click to expand...
Click to collapse
Unless having multiple connections causes the BT to fail completely, no. Even after turning the car off and walking away, it still will not connect to the S Pen. The only BT devices I use with that phone regularly are:
S Pen, Car (Music & Calls)
At work I develop devices that use Bluetooth and I sometimes connect to them, but only ever one at a time.