Enable Tethering / Hotspot Without Rooting AT&T S4 - AT&T Samsung Galaxy S 4 General

Enable Tethering / Hotspot Without Rooting AT&T S4 - AT&T Samsung Galaxy S 4 General

One Way .. First You Wait For Next Update . On That OTA Update .zip File ..
Eg Location : I337_NC1 to NI1_OTA_Update\patch\system\app\TetheringProvision.odex
Replace With http://forum.xda-developers.com/showthread.php?t=2535141 In This Link You Can Download The TetheringProvision.apk
Or Below Attached Check
TetheringProvision.apk and TetheringProvision.odex . Rename them to any name that you want, or just change apk and odex to bak .
Then Again .zip It. Then Update Via abd Sideloader
We Can Use This Method To Update Our Phone :
1) Install Samsung USB Drivers
2) Start Samsung Recovery [ Volume Up + Home + Power ]
3) Select " Apply Update From The ADB "
4) On PC : Install Minimal ADB and Fastboot Software ... Then Put The Update File (ZIP) On The Same Folder
5) Open Minimal ADB and Fastboot : After Type : - adb sideload FILE NAME.zip
5) Updated Successfully.
Afterwards Just Turn On Wifi Tethering / Hotspot .. It Will Works :laugh:
My Friend Tried This Method . Till Now I Didn't Try ..
Take U'r Own Risk

Related

[MOD] 4 way reboot menu for GT-S7562 [Stock] [Odexed] [XXBMD2]

Hello everyone!
i admit, i have been a lurker since the start of xda
so now i decided to share a mod for GT-S7562 (samsung galaxy s duos) which i have managed after a lot of head banging.
MOD TYPE :
4 way reboot for odexed Stock Rom
Firmware Details:
Build : IMM76IS7562XXBMD2
Baseband : S7562DDBMD1
Screenshots :
http://forum.xda-developers.com/attachment.php?attachmentid=2049319&stc=1&d=1371462382
http://forum.xda-developers.com/attachment.php?attachmentid=2049320&stc=1&d=1371462382
+++++++++++ IMPORTANT ++++++++++++++++++
1. DONT TRY THIS IF YOU ARE UNROOTED.
2. DONT TRY THIS IF YOU DONT HAVE CUSTOM RECOVERY (cwm recovery).
3. ANYTHING CAN GO WRONG, DON'T START THE BLAME GAME.
4. NO!! I DON'T TAKE ANY RESPONSIBILITY IF YOU MESS UP!!
5. ALWAYS MAKE A FRESH BACKUP (nandroid backup) BEFORE APPLYING ANY MOD.
+++++++++++++++++++++++++++++++++++++++++
Stepwise instructions:
1. Make sure you have the same baserom / build, it just might not work if you are on a different build / firmware.
2. Extract the files in attachment to c:\adb, Don't change the location because the patcher.bat is written for this location.
3. Connect your phone via usb cable and wait for the computer to recognize it.
4. Make sure you have enabled USB Debugging in developer options on the phone (Settings > Developer options > USB Debugging).
5. As a test for successful connection try and run on command prompt [c:\adb> adb shell] if its showing [[email protected]:/ $] that means connection ok.
6. Further test you have SU access by typing [[email protected]:/ $ su ] if your phone now shows [[email protected]:/ #] that means you have su working.
7. Must also have busybox installed in phone.
8. Now all set, exit adb shell su by exit.
9. On Command prompt c:\adb> type patcher.bat .
10. Phone would reboot and after booting is finished you will have 4 way reboot menu when you select restart option in power menu.
Though i have taken every care in writing this guide, if anyone want's to go further in details, reply in this thread and i might explain all the details further, or if this doesn't works for you ... well i have another script waiting for it, but i am almost certain this would work for everyone on the same firmware as mine.
best regards,
richie

https://www.virustotal.com/sv/file/...c62d71a33cea4b22ef318a23/analysis/1371468288/
ByteHero says that the .zip is infected with the following virus: Trojan.Malware.KillAV.Gen.001
Hope that it's false positive, after all, Kasperksy and Bitdefender says nothing.

X-zone said:
https://www.virustotal.com/sv/file/...c62d71a33cea4b22ef318a23/analysis/1371468288/
ByteHero says that the .zip is infected with the following virus: Trojan.Malware.KillAV.Gen.001
Hope that it's false positive, after all, Kasperksy and Bitdefender says nothing.
Click to expand...
Click to collapse
ROFL !! byte hero needs a serious virus check its just few files of which 2 files are android.policy.jar and android.policy.odex, 1 batch file , 4files of ADB.....

update.zip
tried making an update.zip for s7562 .... hope this works, make sure you backup first !!

Can I have a deodexed BMD6 version of this. As u can see In my signature I'm using SIlverNexus ROM which I made nd its Deodexed.

How to install u10 update in u251 version?

I'm new user in this forum.
I have the g6-u251 version, and My question is that i don't know how install the u10 B330 version update. Please help me!
POR FAVOR AYUDEN
ANDROID 4.4 EMUI 3 IN ASCEND G6 U251?

I dont now if works..., and this is B360!
dvf1278 said:
I'm new user in this forum.
I have the g6-u251 version, and My question is that i don't know how install the u10 B330 version update. Please help me!
POR FAVOR AYUDEN
ANDROID 4.4 EMUI 3 IN ASCEND G6 U251?
Click to expand...
Click to collapse
ROM B360 AVAILABLE for G6-U10.
-----
- Download official B136 Rom from austrian Huawei site
http://download-c.huawei.com/downlo...343&version=54000&siteCode=at&hc_location=ufi
- Extract the dload folder to PC and copy to SD card.
- Go to Options→System Info→Update System→Local Update
---- Phone will reboot in recovery mode and install the update. At the end you'll have Emui 2.0 JellyBean Rom B136 as your system
------------ If you previously flashed a custom recovery (i.e. CWM or TWRP) deleting the stock one, you'll get an error similar to "E:Invalid command argument". You have two solutions:
---------------- 1)Turn off the phone, press Volume DOWN+Volume UP+Power buttons, release power on boot, vols when start to flash it.
---------------- 2)Download this, is the original recovery image, https://docs.google.com/file/d/0B0xf81pxOQgxTVpxU3RaTWNyRWc/edit and flash it by fastboot with ADB,
fastboot flash recovery recovery.img
- Now reboot the phone and it should notifies of an available update to KitKat, rom B360. Simply accept the update.
- If update doesn't get proposed, download this file:
update.zip - https://drive.google.com/file/d/0B0xf81pxOQgxcWs1QVlLNllPVlE/view?usp=sharing&hc_location=ufi&pli=1
- Put the archive update.zip into "HwOUC" folder inside the sd-card, if dont have it you can created
- Go to Options→System Info→Update System→Local Update
---- Your system will be updated to Emui 3.0 KitKat Rom B360.
------If not, turn off the phone, press vol UP and power, clean cache and go to update by zip, look for the file update.zip
------Done
If you have missing apps in the end, to fix you need bootloader unlocked:
!!!!!!»»»»»»»»»»»How to Unlock your bootloader««««««««««««!!!!!
1º Request code to Huawei by e-mail
Ex:
" Hi!
My name is (your name) and I hereby request the bootloader code for my new smartphone HUAWEI ASCEND (your phone model) if possible.
Product SN: (In the backs)
IMEI: ( in key pad *#06# )
Product ID: ( in key pad *#*#1357946#*#*)
Thank you for your attention;
(your name) "
->This are the e-mails (Use the PC, is better) :
[email protected]; [email protected]
PS: When copy paste to send it, please change what is inside of ( ), there are how send it like it is!!!!! Belive me, you never, never,never gona recive anything if goes like this!!!!
When you get the code!
You need ADB!
This one have already a software to unlock the phone
( Huawei_Bootloader_Unlocker ). and , than press "Desbloquear":
https://meocloud.pt/link/32ef02e9-4fd9-4963-ab33-622536ff34ff/ADB/
Only need to extract ADB folder from zip to desktop
--------------------------------------------------------------------------------
-with phone ON, turn on debug mode, open ADB_TOOLS folder and execute Boot_in_fastboot_mode.exe
»»»» OR
->Turn off the phone
->press vol - and power, release power on boot, release vol when you see the fastboot screen
--------------------------------------------------------------------------------
->plug the usb, let pc install the phone
->see if pc find the phone, execute See_if_phone_is_recognized.exe
-> must say samething like - 584566515 fastboot
-> if not, you must install the drivers for the phone or change the usb door.
->execute Huawei_Bootloader_Unlocker from the folder ADB TOOLS
->insert the code where says "Unlock code"!
->click in "desbloquear!"
->phone reboot and do a factory reset.
->Done
Now you need CWM recovery and kinguser.zip to root, Download this files:
-CWM-U10.zip:https://mega.co.nz/#!XpYxGC6D!K0dE4-sr7LmauOrVTRwlE5Qx8eX-mKfqNkTXteUkrTU
-UPDATE-Kinguser-3.4.0:https://mega.co.nz/#!bhp2AZyL!6R1zHtVrWC08tkHAcxv5XtwfjZjx_VbjV3qH2ezELuo
1. Unlock bootloader: https://www.facebook.com/groups/huawei.g6.development/permalink/457458214413436/
2. Download adb if you dont have it, from the link above:
3. extrad ADB TOOLS from zip to desktop, open it and open ADB_TOOLS
4. In PC go to c:\Windows\System32 look for cmd, COPY and paste in ADB_TOOLS.
5. Press volume down and power button to go in fastboot mode, and plug the phone in to PC.
6. Open cmd (doble click in cmd)
7. Type this:
Fastboot flash recovery CWM.img
fastboot reboot
8. Copy "UPDATE-Kinguser-3.4.0.zip" to your SD CARD
9. Turn OFF the phone, press vol + and power, release power on boot to go to recovery mode CWM
10. clear cache
11. Press install zip from sd card
12. Click update UPDATE-Kinguser-3.4.0.zip
13. wait for confirmation and after that when it complete REBOOT your phone
14. After rebooting go to Google play and install any root checker to see if is OK.
Now fix Cust:
The Roms are created for a specific provider , with a specific configuration. A ROM can be compatible with various models , such as U10 with the U251 , L11 with P7mini or even between the same zone countries .
But in the end we find small problems , such as lack of Shortcut Bar in version 4.3 and lack of applications in version 4.4 ! It has to do with the configuration of the CUST folder. How to fix ? We need access ROOT and an explorer as the Root Browser , which can be found in Google Play.
With Root Browser, in this case, we will go to folder /DATA and seek the custom.bin file, open it as a text file, you will see something such as vodafone/pt, for example, now we left the folder /DATA and go to the folder /CUST , we open it and we will usually find a folder with the name hw, we will change the name of it to the first name that we saw in custom.bin in our example will is vodafone, use small font, now we entered the vodafone folder and we will find another folder that usually his name is normal, let's switch to the second name of our exemple which will be pt, use small font!
Now just leave the Root Browser , turn off your phone , enter the recovery , perform a factory reset and start the phone normally.All will be fixed.
Tell if works!

like write data
[Hi, I have the g6 u251 but when i try to install it, says something like write data error update.app is a invalid package, how do i fix it?

[Guide](Tmp/Permanent TWRP) Get Root and Xposed on MIUI 7/8 (Tested on Both)

First and Foremost : If you think that i am a noob and you should not follow my guide then don't. If you do follow my guide then looks at my posts and threads from before.
******************************************************************
1 ) Stuff to Download Link to Mega Folder
^ This Folder Contains everything that you need to download for flashing and stuff
Link to ADB/Fastboot Instaler
^ For The actual flashing of recovery
^^ This Stuff Should Be installed/Downloaded before you do anything at ALL !!!
******************************************************************
- For Root/Xposed1 ) Keep The Following files on your Internal Storage.
- xposed-v87-sdk21-arm64-MIUI-edition-by-SolarWarez-20161126.zip
- xposed-uninstaller-20150831-arm64.zip
- XposedInstaller_3.1.1.apk
- twrp-3.0.2-0-ferrari.img
- SR2-SuperSU-v2.79-SR2-20170103215521.zip
- Deep_Sleep for MIUI.zip
Keep This File on Your PC
- Twrp 2.x.img ( RENAME IT TO TW)
2 ) Connect Your Device to The Pc. Enable Developer Mode and USB Debugging Beforehand
- Go to the folder where your twrp file is located and press Shift+Right Mouse Button and choose open command window Here
3 ) Type in The Following Commands
adb reboot bootloader
Click to expand...
Click to collapse
fastboot boot TW.img
Click to expand...
Click to collapse
4 ) Soon TWRP will load up swipe to access it.
5 ) If You want to ROOT ONLY Then Only Flash SR2-SuperSU-v2.79-SR2-20170103215521.zip and Reboot.
6 ) If you want Xposed As well then flash xposed-v87-sdk21-arm64-MIUI-edition-by-SolarWarez-20161126.zip and Reboot
6 1/2 ) Flash The Deep Sleep Patch For Better Battery Life
If You reboot now TWRP will be Erased/Not Be Installed/Remain on Your Device. To Install It permanently Follow Below
7 ) If You want Permanent TWRP then go to Install And Click on Images Button and then select twrp-3.0.2-0-ferrari.img and Next Choose Recovery Partition. Then Reboot to recovery and You will see new and updated twrp.
******************************************************************
Boot back to The System
go to SuperSU and Set it Up
Go to File Manager and install Xposed and Install Modules.
******************************************************************
This Thread Will Be Updated With more Information Soon.

[Resolved] Trouble shoot for Xolo Era X and 4G Twrp installation.

Hello Everyone -
Welcome back , In previous post i explained " How to install twrp and root Xolo Era X,4G" but i forgot to mention some things which resulted errors for many users making it non-beneficial , I mean wasted time , data , or may be the android rom. Thanks for describing problems in previous post.Now it's mine turn to return you something original , something good .Search your question answers here and problems.
Please note that this thread is only for Xolo era X , 4G marshmallow 6.0 version only , 5.1 is not supported .Sorry but update to 6.0.
1. `adb` is not recognized as an internal or external command
Ans - If you are facing this error then probably you are not in the folder where adb and fastboot tools are installed .
You have to open command prompt only where adb tools,drivers are installed.Still not solving then google it.
2. adb devices = blank (nothing is shown)
Ans - I think you have either not connected your smartphone with usb debugging on or you have not installed proper version of adb and fastboot drivers.Please google for different versions of adb and fastboot.
3. fastboot devices = blank (nothing is shown)
Ans - Same as in above answer.
4. fastboot flash recovery recovery.img = <waiting for device>
Ans - It means that you have not installed fastboot drivers properly or you have not connected your devices in fastboot mode.
5. fastboot flash recovery recovery.img = no such file found or recovery.img not found.
Ans - You have not copied or moved recovery.img(twrp or cwm image file) in the folder where adb and fastboot are installed .So put the recovery.img (it can be twrp.img or somename.img) in the adb and fastboot tools folder(it can be either found in local drive C or at any custom location) .
6. Recovery Installed successfully but still booting in stock recovery or Computer shows installation successful but still opens stock recovery.
Ans - This is a great problem for many users and it is happening due to security policies of android 6.0. To fix it Do as following-
(1) Install twrp recovery and when it say success plug your battery out .
(2)Put battery back and open smartphone in recovery mode by holding VOL Up + Power Button for 15 seconds.
(3)Now your smartphone will boot in TWRP recovery but your twrp recovery is still temporary .
(4)Install SuperSu.zip by twrp recovery and this zip file will patch boot.img and system files.
(5)After installation of zip file reboot your smartphone .
(6)Your smartphone will restart 2-3 times and finally will boot .
(7) Finally you have rooted your smartphone and installed TWRP permanently .Now install busybox and enjoy.
Note: Please Select Expert Mode when you open SuperSu app first time after this process(you will be asked by SuperSu app to select two modes 1 Expert , 2 New User ; always select Expert or root will not function properly).
I hope you got what you wanted . If i helped you then please Subscribe , like and share also Hit thanks here on xda.
Download SuperSu zip from here - https://drive.google.com/open?id=0B_Mx_zMB6YZOUENHdHpDTXZucXc

Finaly
ankitnandgavia said:
Hello Everyone -
Welcome back , In previous post i explained " How to install twrp and root Xolo Era X,4G" but i forgot to mention some things which resulted errors for many users making it non-beneficial , I mean wasted time , data , or may be the android rom. Thanks for describing problems in previous post.Now it's mine turn to return you something original , something good .Search your question answers here and problems.
Please note that this thread is only for Xolo era X , 4G marshmallow 6.0 version only , 5.1 is not supported .Sorry but update to 6.0.
1. `adb` is not recognized as an internal or external command
Ans - If you are facing this error then probably you are not in the folder where adb and fastboot tools are installed .
You have to open command prompt only where adb tools,drivers are installed.Still not solving then google it.
2. adb devices = blank (nothing is shown)
Ans - I think you have either not connected your smartphone with usb debugging on or you have not installed proper version of adb and fastboot drivers.Please google for different versions of adb and fastboot.
3. fastboot devices = blank (nothing is shown)
Ans - Same as in above answer.
4. fastboot flash recovery recovery.img = <waiting for device>
Ans - It means that you have not installed fastboot drivers properly or you have not connected your devices in fastboot mode.
5. fastboot flash recovery recovery.img = no such file found or recovery.img not found.
Ans - You have not copied or moved recovery.img(twrp or cwm image file) in the folder where adb and fastboot are installed .So put the recovery.img (it can be twrp.img or somename.img) in the adb and fastboot tools folder(it can be either found in local drive C or at any custom location) .
6. Recovery Installed successfully but still booting in stock recovery or Computer shows installation successful but still opens stock recovery.
Ans - This is a great problem for many users and it is happening due to security policies of android 6.0. To fix it Do as following-
(1) Install twrp recovery and when it say success plug your battery out .
(2)Put battery back and open smartphone in recovery mode by holding VOL Up + Power Button for 15 seconds.
(3)Now your smartphone will boot in TWRP recovery but your twrp recovery is still temporary .
(4)Install SuperSu.zip by twrp recovery and this zip file will patch boot.img and system files.
(5)After installation of zip file reboot your smartphone .
(6)Your smartphone will restart 2-3 times and finally will boot .
(7) Finally you have rooted your smartphone and installed TWRP permanently .Now install busybox and enjoy.
I hope you got what you wanted . If i helped you then please Subscribe , like and share also Hit thanks here on xda.
Download SuperSu zip from here - https://drive.google.com/open?id=0B_Mx_zMB6YZOUENHdHpDTXZucXc
Click to expand...
Click to collapse
Wahooooooo I it happened. Its done TWRP flashed successfully n my phone Is rooted. Big thanks to you and Murali Dharan and that's how it's done. Here is some point
Es file explorer can't excess root of my phone even if I hit allow.
All other root app are working fine
Can I reflash super user zip of kingo root I am asking coz there was additional files with superuser files u provided to fix twrp
I have lost ur channel put links n I will like n subscribe

CheifX said:
Wahooooooo I it happened. Its done TWRP flashed successfully n my phone Is rooted. Big thanks to you and Murali Dharan and that's how it's done. Here is some point
Es file explorer can't excess root of my phone even if I hit allow.
All other root app are working fine
Can I reflash super user zip of kingo root I am asking coz there was additional files with superuser files u provided to fix twrp
I have lost ur channel put links n I will like n subscribe
Click to expand...
Click to collapse
Hii ,
When you open SuperSu app first time , Please select Expert Mode otherwise root will not work even after granting permission.

ankitnandgavia said:
Hii ,
When you open SuperSu app first time , Please select Expert Mode otherwise root will not work even after granting permission.
Click to expand...
Click to collapse
Hallooooo!
I have already selected expert mode and other root apps working perfectly fine.

CheifX said:
I have already selected expert mode and other root apps working perfectly fine.
Click to expand...
Click to collapse
Then please update or install busybox or you have to restart device after installing busybox or try changing es explorer app version..Es file explorer with root is working fine in mine smartphone.

ankitnandgavia said:
Then please update or install busybox or you have to restart device after installing busybox or try changing es explorer app version..Es file explorer with root is working fine in mine smartphone.
Click to expand...
Click to collapse
I will try busybox later what about reflashing kingo root supperuser.

Es explorer root mot work in xolo era 4g ..same with me........can u provide cwm for my phone 5.1....plzzz

CheifX said:
I will try busybox later what about reflashing kingo root supperuser.
Click to expand...
Click to collapse
Flashing kingo root superuser is not a bad idea, you can try it but be aware of risks so take a backup through TWRP.You can try anything new after taking backup,if something goes wrong then restore your backup.Good luck.

Need latest twrp recovery
I want the latest version of recovery for xolo era 4g and want some custom roms....plz make it.....plzz

I'm facing an issue with the OEM Unlock toggle in developer options. When I toggle it On and select OK for the pop-up box that comes. It automatically disables it. Can u help me out with this and tell me why I'm facing this issue?

yes.. i was too facing this problem but if u are trying to install custom rom then u can flash 5.1 version through SPD Upgrade Tool and then toogle that option then install ur custom rom...
no option is there!

[Resolved] How to root Vodafone Smart Tab 7 (Tablet) VFD 1100 (Solved)

Hello,
After i searched almost 24 hours on the web for a way to root this stupid tablet, i find an unusual one.
I try to make it clear for all of you.
Requirements:
- PC running Windows 7/8/8.1/10 | You can use linux but I cannot guide you as how to setup adb drivers or preloader drivers,
- USB Cable,
- ADB-Setup file (see below),
- TWRP recovery aka recovery.img.zip,
- SP_Flash_Tool (SPFT),
- MT6580_Android_scatter.txt (see below),
- MTK_USB_All preloader usb vcom drivers,
- superuser.zip (don't confuse this file with phh superuser, they are not the same),
- phh superuser (install it at the end, on the tablet).
DO NOT EXTRACT the superuser.zip !!
You can extract all other files.
Flashing TWRP
1. Download the MTK_USB_All preloader drivers from the archive of this post and follow the guide on how to install.
2. Download the new SP_Flash_Tool from the archive of this post and extract it anywhere.
3. Open the SPFT folder and locate flash_tool.exe and RUN it as Administrator.
4. If it says anything like cannot locate scatter, press ok and ignore that message. Go to scatter loading and select your MT6580_Android_scatter file you downloaded.
5. Download TWRP recovery aka recovery.img.zip from the archive of this post.
Extract the archive to get the recovery.img file.
5.1 After you open the flash_tool.exe, look on the list from the scatter file for recovery; Follow step 6.
6. Select the recovery by pressing the little box next to it and then move over to location of the recovery and choose the recovery.img.
7. Power off your tablet, wait 1-2 minutes and then connect your usb cable to your PC.
8. Press Download at the top and then connect your tablet to your PC throught the USB Cable.
If you have the battery in and it doesn't work, wait until the logo of the tablet shows up then try again. If that doesn't work then try again without the battery.
8.1 When the Download is finished (you will see a red bar, then a green bar to confirm), if the tablet doesn't open up, remove the USB Cable from it and wait for few seconds.
Then the TWRP menu should appear. This should do the magic.
Rooting:
1. Download superuser.zip from the attached files and place it on your SD card.
1.1 ADB arhive has in it a ADB Drivers installer that only needs 15 seconds to do the trick. Please follow the instructions from there.
1.2 ADB folder will be located from default on partition C, or if you have another one, on the OS partition.
2. Reboot your phone to recovery using the command "adb reboot recovery" from a CMD runned as administrator from the ADB folder, or do it via external buttons.
2.1 When you execute the command "adb reboot recovery" the TWRP Menu will appear.
3. Navigate using volume buttons and select using power button, or touch if you want. Go to install from the TWRP Menu then choose superuser.zip from SD card.
Flashing should take only few secconds, then reboot your tablet.
4. Install phh superuser app from the arhive of this post and that's it. You will be rooted.:good:
* I hope this will help you to do this step more easily then me. Be well !
Password for archive is: vfd1100

DevOpsXDA said:
Hello,
After i searched almost 24 hours on the web for a way to root this stupid tablet, i find an unusual one.
I try to make it clear for all of you.
Requirements:
- PC running Windows 7/8/8.1/10 | You can use linux but I cannot guide you as how to setup adb drivers or preloader drivers,
- USB Cable,
- ADB-Setup file (see below),
- TWRP recovery aka recovery.img.zip,
- SP_Flash_Tool (SPFT),
- MT6580_Android_scatter.txt (see below),
- MTK_USB_All preloader usb vcom drivers,
- superuser.zip (don't confuse this file with phh superuser, they are not the same),
- phh superuser (install it at the end, on the tablet).
DO NOT EXTRACT the superuser.zip !!
You can extract all other files.
Flashing TWRP
1. Download the MTK_USB_All preloader drivers from the archive of this post and follow the guide on how to install.
2. Download the new SP_Flash_Tool from the archive of this post and extract it anywhere.
3. Open the SPFT folder and locate flash_tool.exe and RUN it as Administrator.
4. If it says anything like cannot locate scatter, press ok and ignore that message. Go to scatter loading and select your MT6580_Android_scatter file you downloaded.
5. Download TWRP recovery aka recovery.img.zip from the archive of this post.
Extract the archive to get the recovery.img file.
5.1 After you open the flash_tool.exe, look on the list from the scatter file for recovery; Follow step 6.
6. Select the recovery by pressing the little box next to it and then move over to location of the recovery and choose the recovery.img.
7. Power off your tablet, wait 1-2 minutes and then connect your usb cable to your PC.
8. Press Download at the top and then connect your tablet to your PC throught the USB Cable.
If you have the battery in and it doesn't work, wait until the logo of the tablet shows up then try again. If that doesn't work then try again without the battery.
8.1 When the Download is finished (you will see a red bar, then a green bar to confirm), if the tablet doesn't open up, remove the USB Cable from it and wait for few seconds.
Then the TWRP menu should appear. This should do the magic.
Rooting:
1. Download superuser.zip from the attached files and place it on your SD card.
1.1 ADB arhive has in it a ADB Drivers installer that only needs 15 seconds to do the trick. Please follow the instructions from there.
1.2 ADB folder will be located from default on partition C, or if you have another one, on the OS partition.
2. Reboot your phone to recovery using the command "adb reboot recovery" from a CMD runned as administrator from the ADB folder, or do it via external buttons.
2.1 When you execute the command "adb reboot recovery" the TWRP Menu will appear.
3. Navigate using volume buttons and select using power button, or touch if you want. Go to install from the TWRP Menu then choose superuser.zip from SD card.
Flashing should take only few secconds, then reboot your tablet.
4. Install phh superuser app from the arhive of this post and that's it. You will be rooted.:good:
* I hope this will help you to do this step more easily then me. Be well !
Password for archive is: vfd1100
Click to expand...
Click to collapse
Hi, i can use this way Also for Vodafone Smart Tab 10?

Database Info

welcome