Found this online. *****this is not my work****** All credit goes to the author quattrodevelopment.blogspot.com
Here is a step by step with roms included for the 4.5 quattro Not the HD or 5.7 HD maybe soon.
Disclaimer: These ROMs/Recoveries are only intended for the BLU Quattro 4.5, or the K-Touch v9(which is the chinese version) These WILL NOT work on the 4.5HD or 5.7HD devices(I will release ROMs/Recoveries specifically for your device at a later time)
Drivers: https://copy.com/BUMmsS9rhLJe
English Recovery: https://copy.com/XZxTDht2lQiz
Gapps(4.2) https://copy.com/utkbZgwRpsVB
Gapps(4.1) https://copy.com/pSd8SsqU9pdI
ROMs With Less Bugs: MIUI v5 (4.1) https://copy.com/sbmcN6PHwFfi CM/AOKP Hybrid? JB (4.1) https://copy.com/VeLz1VLbkNNI Shendu ROM 4.1(Modified/Tweaked by me) https://copy.com/NwiFnlO8JAek
ROMs With More Bugs: Cyanogenmod 10.1 (4.2) https://copy.com/8kt2EAU2ll8y
1- Download the drivers from link posted above, and extract it to the folder of your desire. Now turn the phone off, and hold Vol+ (volume up button) and Power button at the same time until you see a green screen, then release both buttons immediately. You should now be in APX mode(nvflash) it will be a black screen
2- Connect phone to computer via usb cable. Now you should get a pop-up window about installing drivers, you're going to want to choose to browse computer for driver software manually. Then choose let me pick from a list of device drivers on my computer, and click have disk. Now you're going to browse to the location where you extracted the drivers to, and click on it(Ignore warning if it pops up, and choose install)
3- Assuming everything went as planned, now download the recovery and extract it to the location you desire(must be in a directory that you can issue adb commands from) inside of that folder, locate a file named recovery.bat. Double click on that file and a command prompt with a bunch of chinese pops up. Give it a second and press enter, it will go through the process and flash a recovery onto your phone
4- After everything is done, hold down the power button for about ten seconds(until the device powers off) Power the device back on normally, and download the ROM/ROMs if you haven't already and place them on the internal or external sd card(your choice) With device connected to pc, open command prompt and type in "adb reboot recovery" (without quotes) and the device will boot into recovery mode
5- Now that we have an English recovery, the translations below aren't really needed. However, I'm going to leave them up for a few days, just until everybody can transition to the English recovery. They will be deleted after that!
Recovery Main Menu: -Reboot -Install from SD card -Wipe Data/Factory Reset -Wipe Cache -Backup&Restore -Mount/Format -Advanced
Install From SD Card Menu: -Install zip from external SD -Apply update.zip -Unknown* -Install zip from internal SD
Backup&Restore Menu: -Backup -Restore -The rest are unknown*
Advanced Menu: -Reboot Recovery -Wipe Dalvik Cache -The rest are unknown*
To install ROM- In recovery mode, Factory Reset/Wipe Cache/Wipe Dalvik Cache. Then choose install zip from sd card(then choose internal or external and locate the ROM you want to install) After that you need to do the same thing to install the gapps package(you need the gapps package for google apps to function) once all is done, reboot and wait(it takes a while to boot the first time after flashing new ROMs, it has to rebuild the Dalvik cache)
NOTE: In case you aren't familiar with flashing ROMs, once you click on something( "backup" for example) a menu pops up pretty much asing you if you're sure you want to do that. It will have a bunch of lines of the same thing(which is no) and then one of the lines will have a bunch of writing beside it(which means yes). Also BEFORE you flash any ROMs, make sure you factory reset/wipe cache/and wipe dalvik cache, then you can flash the ROM and gapps package
*These will be updated regularly, as I discover what they are **More ROMs to come!
Internal Memory
The "BLU Quattro 4.5" has 4GB internal memory partitioned into 0.98GB for ROM and apps and an internal usb-memory of 1.63GB.
Is it possible to merge or resize the partitions?
I have 16GB external SD so the 1.63GB internal reserved usb-memory is useless and I still having trouble out of space in primary partition.
Thanks and sorry my english =/
TechSoft said:
Found this online. *****this is not my work****** All credit goes to the author quattrodevelopment.blogspot.com
Here is a step by step with roms included for the 4.5 quattro Not the HD or 5.7 HD maybe soon.
Disclaimer: These ROMs/Recoveries are only intended for the BLU Quattro 4.5, or the K-Touch v9(which is the chinese version) These WILL NOT work on the 4.5HD or 5.7HD devices(I will release ROMs/Recoveries specifically for your device at a later time)
Drivers: https://copy.com/BUMmsS9rhLJe
English Recovery: https://copy.com/XZxTDht2lQiz
Gapps(4.2) https://copy.com/utkbZgwRpsVB
Gapps(4.1) https://copy.com/pSd8SsqU9pdI
ROMs With Less Bugs: MIUI v5 (4.1) https://copy.com/sbmcN6PHwFfi CM/AOKP Hybrid? JB (4.1) https://copy.com/VeLz1VLbkNNI Shendu ROM 4.1(Modified/Tweaked by me) https://copy.com/NwiFnlO8JAek
ROMs With More Bugs: Cyanogenmod 10.1 (4.2) https://copy.com/8kt2EAU2ll8y
1- Download the drivers from link posted above, and extract it to the folder of your desire. Now turn the phone off, and hold Vol+ (volume up button) and Power button at the same time until you see a green screen, then release both buttons immediately. You should now be in APX mode(nvflash) it will be a black screen
2- Connect phone to computer via usb cable. Now you should get a pop-up window about installing drivers, you're going to want to choose to browse computer for driver software manually. Then choose let me pick from a list of device drivers on my computer, and click have disk. Now you're going to browse to the location where you extracted the drivers to, and click on it(Ignore warning if it pops up, and choose install)
3- Assuming everything went as planned, now download the recovery and extract it to the location you desire(must be in a directory that you can issue adb commands from) inside of that folder, locate a file named recovery.bat. Double click on that file and a command prompt with a bunch of chinese pops up. Give it a second and press enter, it will go through the process and flash a recovery onto your phone
4- After everything is done, hold down the power button for about ten seconds(until the device powers off) Power the device back on normally, and download the ROM/ROMs if you haven't already and place them on the internal or external sd card(your choice) With device connected to pc, open command prompt and type in "adb reboot recovery" (without quotes) and the device will boot into recovery mode
5- Now that we have an English recovery, the translations below aren't really needed. However, I'm going to leave them up for a few days, just until everybody can transition to the English recovery. They will be deleted after that!
Recovery Main Menu: -Reboot -Install from SD card -Wipe Data/Factory Reset -Wipe Cache -Backup&Restore -Mount/Format -Advanced
Install From SD Card Menu: -Install zip from external SD -Apply update.zip -Unknown* -Install zip from internal SD
Backup&Restore Menu: -Backup -Restore -The rest are unknown*
Advanced Menu: -Reboot Recovery -Wipe Dalvik Cache -The rest are unknown*
To install ROM- In recovery mode, Factory Reset/Wipe Cache/Wipe Dalvik Cache. Then choose install zip from sd card(then choose internal or external and locate the ROM you want to install) After that you need to do the same thing to install the gapps package(you need the gapps package for google apps to function) once all is done, reboot and wait(it takes a while to boot the first time after flashing new ROMs, it has to rebuild the Dalvik cache)
NOTE: In case you aren't familiar with flashing ROMs, once you click on something( "backup" for example) a menu pops up pretty much asing you if you're sure you want to do that. It will have a bunch of lines of the same thing(which is no) and then one of the lines will have a bunch of writing beside it(which means yes). Also BEFORE you flash any ROMs, make sure you factory reset/wipe cache/and wipe dalvik cache, then you can flash the ROM and gapps package
*These will be updated regularly, as I discover what they are **More ROMs to come!
Click to expand...
Click to collapse
Please rename this For Others Such as [GUIDE]BLU Quattro HowtoRoot/Rom list. Thanks for the awesome Guide!
alanfrank said:
The "BLU Quattro 4.5" has 4GB internal memory partitioned into 0.98GB for ROM and apps and an internal usb-memory of 1.63GB.
Is it possible to merge or resize the partitions?
I have 16GB external SD so the 1.63GB internal reserved usb-memory is useless and I still having trouble out of space in primary partition.
Thanks and sorry my english =/
Click to expand...
Click to collapse
I've found this: http://forum.xda-developers.com/showthread.php?t=1171531
Any idea if this can be used with another phone them the LG one he have used in the guide?
I cant post in the thread because Im new user here =/
problem
I have done everithing you said, and my cell freezes on boot forever, now what????
BLU Quattro 4.5 HD & 5.7
Need to know how to restore both devices to stock. Any aplication ODIN like to restore it back to stock from the download mode?
Please help me root, i try binary method but i just get boot loop.
Recovery + Root My experience
Hello... I got my BLU Quattro 4.5 (D440) a while back, didn't fuzz with it much right off. The Stock ROM was sluggish at best thought there was even an issue with the Digitizer/screen. But this thread was extremely helpful. I am now running Shendu ROM 4.1.2 one of the suggested ROM's above. I tried the other 2 first and they were mostly in Chineese and I had an especially hard time getting them switched over to English. Either way onward to the point. I have put together a few helpful tips-tricks for my experience with this phone and its phoenix transition to an awesome handset. Thats right now this is my daily driver and I love it! See below hope its helpful.
BLU Quattro 4.5 (440D) GSM Recovery+Root
These steps for this phone only!! Not responsible for any issues.
1. download ROM's, Recovery, & Driver from XDA (this thread)
http://forum.xda-developers.com/showthread.php?t=2327417
2. Enable USB Debugging! Go into Apps-Settings-DevOptions - Check box for USB Debug
3. Have original USB cord if handy! I tried with a Samsung OEM cable but no luck getting drivers to stick. Use original is best. (If you have one.)
Plug in USB Cord to PC then Phone and see if windows detects drivers. let it. It wont get the ones u need later, but what it does find is for USB storage. (you can move over your ROM's/Gapps to storage, downloads folder is a good spot).
4. Go to... http://junefabrics.com/android/downloadold.php to get pdanet software. Install it and it will give i the right drivers for ADB support. I used 4.01 to match the android version currently on my phone.
5. Extract the Driver provided from XDA. Put it in a folder with the ADB commands. Or you can get it all here... http://downloadandroidrom.com/file/GalaxyNexus/rooting/GalaxyNexusRootNew.zipn <-- I know this isn't for BLU but, if you extract this to a folder, and also add the drivers extracted to it as well this works! I've done it.
6. Extract the English Recovery to the same folder.
7. Turn off your phone. Hold down Vol up and Power button for about 5-9 seconds. Once you see a green screen let go of both. Screen may flicker then go black but the icons at the bottom will stay lit. You are now in APX mode (nvflash) mode. (as stated above in original post)
8. Check your Win 7 PC device manager. For a Phone device with ADB. If you you may need to update driver with the one that came from XDA, but the PDANet software should make it work.
8. Go to the folder and find Recovery.bat file (may have Chinese in file name. Double click and a command prompt window will pop up with a bunch of unknown characters, wait 5 sec then hit enter. The batch file should take of pushing the necessary recovery through ADB to the phone. It will error if it can't.
9. If completes OK. Push power for 7-9 seconds to power off the phone. Hit power like normal to turn it back on. It will boot up like normal (or it should).
10. USB is still connected this whole time and you can open a command prompt window. Navigate to the folder you placed the Recovery into. Something like user/username/desktop/BLU/recovery..etc)
Type ADB devices....it should show you that is is connected to your device. Then type " adb reboot recovery " and the device should reboot, give it some time.
11. Once in recovery. Best to do a backup of the original ROM & system. that way you can get back into recovery if anything goes wrong and wipe out the problem by restoring and starting again.
After you backup === you can get into recovery without the command being typed in or even being connected to your PC.... By holding Vol up + Power till you see the green screen then let go of power but keep holding Vol up till you see the BLU Products boot screen then let go ===
Clockworkmod Recovery should be on your screen.
you can reboot phone now and get back to original with no changes. Or you can venture into the world of loading ROM's (There in your downloads folder if you saved them in Step 3)
ROM 101
BACKUP-BACKUP-BACKUP 1st thing once in Recovery ...can't stress enough how much of trouble you can keep yourself out of by keeping an original backup.
As I stated before the Shendu ROM + Gapps is running smooth and all features I've been trying are working flawlessly!! Thanks to original post for getting me going. Just thought I'd add my 2 Cents.
Ok, here are the BEST 2 ROMS for this Phone:
Android 4.0.4(close to vanilla) : MEGA
Cyanogenmod 10.2 (Android 4.3.1) : (some audio and video issues, in BETA version ) MEGA
Need to merge internal partitions ? (merge memories) this one really "resize" the partitions (first one 1,7GB, another one new size is 2Mb) the flash.cfg file you need to flash:
This phone dont have notificaion led, fixed with this app: MEGA (flash the botton menu buttons)
Altomugriento said:
Ok, here are the BEST 2 ROMS for this Phone:
Android 4.0.4(close to vanilla) : MEGA
Cyanogenmod 10.2 (Android 4.3.1) : (some audio and video issues, in BETA version ) MEGA
Need to merge internal partitions ? (merge memories) this one really "resize" the partitions (first one 1,7GB, another one new size is 2Mb) the flash.cfg file you need to flash:
This phone dont have notificaion led, fixed with this app: MEGA (flash the botton menu buttons)
Click to expand...
Click to collapse
Can you explain the merge memories procedure? it will be reaaaaally needed!!
tryed from a spanish forum with no luck
thanks
dinizbruno said:
Can you explain the merge memories procedure? it will be reaaaaally needed!!
tryed from a spanish forum with no luck
thanks
Click to expand...
Click to collapse
Do you try the procedure posted in 3dgames . com . ar? ( its my work translated from the 592zn page, all the credits for the chinesse people)
Anyone tried the K-touch V9 kit kat in the BLU??
www
needrom
com/
download/
k-touch-v9-miui-v5-kk
Yes, those roms (v5) are very slow. Just use the 4.0.4 stock.
I want to try the JB stock, but i can´t find the official one anywhere.
Blu quattro 4.5 official rom to download, after you delete the bloatware and put a nice and clean theme you´ll get a nice speed.
orig D440 (quattro 4.5) rom
You can find the rom on google plus under BLU Products Development search for the model!
Hope that helps. I took your advice tonight and I am back running old school. Works ok husfar
I need phone.apk of this rom for Blu Quattro
Trozzul said:
Please rename this For Others Such as [GUIDE]BLU Quattro HowtoRoot/Rom list. Thanks for the awesome Guide!
Click to expand...
Click to collapse
I need phone.apk for blu quatro
please send me the file
[email protected]
So by today (22.09.2014) is your phone oficialy renamed from "ZTE Red Bull V5" to "ZTE V5"
POSTING A PROBLEM
If you have some sort of problem with your device please please get us this info, so we could help you:
1-what rom/firmware are you using
2-what recovery
3-if you have rooted your device
4-what caused the problem
5-step by step description what you did before the problem shows up.
Hi i just made this thread to make a base for everyone who bought this (form me) superb phone.
So far we got root, custom recovery, and many chinese roms (based on Nubia UI, Color OS, LEWA OS, FROG OS...).
There are Mokee AOSP 4.4.4. rom in develpoment and CM11 in development, CM12 also.
2015.02.13 - Latest firmware is 1.17 (andorid 4.4.2, nubia UI2.5.1)!!!
Changelog(google translation from chineese):
-optimize the signal problem
-solving open U disk mode or restart the phone, ringtones revert to the default issue
into the video again, this video from one schedule to start playing the video
-update time management software, to solve the problem of the shutdown alarm clock does not ring
-media library interface, Pictures Pictures folder appear as a blank
-to use the gallery under OTG open unsupported file error
-switching to the media library interface, multiple exposure, suggesting that language View screenshot untranslated
-save the video recording status suspended again after recording, the Pause button to display the error
-optimization manually Focus
-video recording in the recording pause again, long display of detailed information is incorrect
-horizontal screen - portrait - horizontal screen operation, not full screen
-video player interface to open the USB mass storage press the return key error
here is link to my google drive. It contains stock roms from 0.50 to 1.12, GAPPS ect. Also contains tools to root and flash custom recovery.
MY GOOGLE DRIVE ZTE V9180 FOLDER
In my Google Drive there is also two custom recovery CWM and TWRP (thanx a lot to FAZERGOO from 4PDA.ru, here on XDA it is fazerg, so please thank him for his work)..the script in my root+recovery folder is updated, so you have option to flash CWM (6.0.5.1) or TWRP (2.8.0.0.)
here is list of commands you can dial in dialer and get some hidden menu and settings:
*#06# - displays IMEI
##36 - update server settings for OTA
*#*#4636#*#* - display phone information, battery information, battery history, usage statistics, WiFi information
*#406# - touch screen calibration
--proximity sensor calibration--
*#777# - no cover of proximity sensor
*#776# - cover proximity sensor with hand 2-5 cm above..so the bar is in the green
*# 405# - MHL test
to go to recovery you have to poweroff the phone and hold "vol+" and "power" for 2 sec
to go to safe mode....???
best resources for ROMS (chinese sites):
bbs.anzhi.com
www.tdbeta.cn
www.ztehn.com
And of course our friends from Russia thread:
www.4pda.ru
proDOOMmans mega drive where you can find all Mokee, CM11, PAC roms:
HERE! and dont forget to hit THANKS button for everyone who develop and help us to use this device!!!!
TIPS & TRICKS
-HOW TO CHANGE LCD DENSITY and switch to phablet UI!!! Beware, the camera app is little bit smaller then the screen, becaouse of the density, but still works well.
-HOW TO ADD ONE HAND FEATURE
-did you know that when holding home button on locked screen lights a flashlight?
-when you double tap home button on locked screen the time changes to media player controls?
-when you tap several times on any home screen your glas will broke?
-when you zoom out with two fingers on any home screen you will get into screen manager?
-in alarm clock app there is setting "power of alarm", when turned on, you can turn off your phone at night and the phone turns on by itself in the alarmclock time and wakes you up?
complete guide by navin_n
People always asking again and again on flashing ROMs, Recovery, GApps, Root etc. So, I have made detailed step by step guide for this. Hope now it will be clear to everyone for these processes:
BEFORE YOU DO ANYTHING FROM FOLLOWING, PLEASE MAKE ANANDROID BACKUP, BEST WITH TWRP!!!BECAUSE TWRP CAN MAKE BACKUP INCLUDING PRESIST AND MODEMST PARTITIONS!!![/CENTER]
GUIDE TO FLASH STOCK ROM:
NOTE:
1. Be sure to backup all important data (contacts, messages, call records, etc.) before proceeding
2. Ensure that Phone Battery is at least 40%.
3. Downloaded required STOCK ROM.
4. Phone with Stock Recovery.
STEPS:
1. Copy the downloaded zipped STOCK ROM to the root directory of External SD card or Internal SD card.
2. Power-off the phone.
3. Put the phone in the Recovery Mode and for this you need to press Vol+ and Power button at the same time for few secs and then release the Power Button.
4. In the Stock Recovery, perform wipe data/factory reset and wipe cache partition (In the menu, use +/- volume keys to scroll up/down & power button for confirmation).
5. Depending on which SD card you have copied the zipped STOCK ROM, choose "Apply update from /sdcard" or "Apply update from external /sdcard" accordingly.
6. Select the zipped STOCK ROM to flash.
7. Wait until you get the confirmation of successful flashing.
8. Reboot the phone by selecting "reboot system now".
9. DONE. (Initial boot may take some time so have patience.)
GUIDE TO INSTALL CUSTOM RECOVERY + CUSTOM ROM:
AS FOR CERTAIN REPORTS IT IS STRONGLY RECOMMENDED TO FLASH CWM RECOVERY IF YOU HAVE 1/8 VERSION
REQUIREMENTS:
1. Be sure to backup all important data (contacts, messages, call records, etc.) before proceeding.
2. Working Windows PC with ADB Drivers installed - without proper installation of drivers the process will not be successful.
3. Ensure that Phone Battery is at least 40%.
STEPS: (If you need only Custom Recovery, then follow the steps from 2 to 7, other steps you can skip)
1. Download the required zipped Custom ROM and copy it to the root directory of External SD card or Internal SD card.
2. Download the Recovery Tool zip file. (Link to download the Tool) . Make sure to download whole files. After that copy the zipped file to the root directory of C:\ or any place you prefer and then unzip the downloaded file.
3. Enable USB debuging mode. ("Menu Button" >> System settings(Settings) >> About phone(On the phone) >> Tap 6 times on Build number>>"Back button">> More >> Developer options >> Enable USB Debugging)
4. Connect the phone to the PC.
5. Go to the folder where you have unzipped the Recovery Tool file, and then execute the batch file "run.bat".
6. In PC, new window will open. Input your choice of Custom Recovery accordingly.
7. Follow the steps on-screen until all completes.
8. After completion, in the Fastboot menu, select "Boot recovery".
9. If the Custom Recovery was flashed succesfully, you will get CWM or TWRP recovery menu.
10. Perform wipe data/factory reset and wipe cache partition.
11. To flash the firmware: Select "Install ZIP" >> "choose zip from sdcard0 or sdcard1" depending on which SD card you have copied the ROM, external or internal >> Select Custom ROM >> Click Yes to flash selected ROM.
12. Wait until you get the confirmation of successful flashing.
13. Reboot the phone by selecting "reboot system now".
14. DONE. (Initial boot may take some time so have patience.)
GUIDE TO INSTALL GAPPs & ROOT:
REQUIREMENTS:
1. Backup all important data (contacts, messages, call records, etc.) before proceeding, if necessary.
2. Requires CUSTOM RECOVERY.(Mandatory)
STEPS:
1. Download appropriate flashable zipped GAPPS & ROOT files and copy it to the root directory of External SD card or Internal SD card.
2. Power-off the phone.
3. Put the phone in the CWM or TWRP Recovery Mode and for this you need to press Vol+ and Power button at the same time for few secs and then release the Power Button.
4. Flash the zipped files (one at a time): Select "Install ZIP" >> "choose zip from sdcard0 or sdcard1" depending on which SD card you have copied the file, external or internal >> Select Zipped File >> Click Yes to flash selected file.
(No need to do wipe data/factory reset and wipe cache partition)
5. After successful flashing, reboot the phone by selecting "reboot system now". If it ask to fix the permission when you reboot, select Yes.
7. Wait until you get the confirmation of successful flashing.
8. DONE. (Your phone will have GApps and Root Permission)
and don´t forget to hit thanx button to @navin_n, @fazerg and me maybe @DallasCZ
APPS taht can be remover (thanx navin_n)
If you have already Rooted your device then you can easily uninstall the system apps using "Root Uninstallers" available in Google Play.
However, for me , i prefer to use Root Explorer and delete the apps from system folder. The following apps are safe to delete but still i advise you to backup the files before deleting. If you use Root Explorer, make sure to change attribute of the system folder from Read Only (R/O) to Read Write (R/W) when deleting.
Be ware you make it on your own!! If there is also odex file, delete them too!!!
APPs that can be deleted:
folder --> /system/app
nubia_account.apk - only if you log in in nubia account (maybe you need this to use themes)
nubia_Calculator_v1.2.1.apk - calculator app (i dont like it so i installe another one and delete this)
nubia_Calendar_v1.0.apk - nubia calendar app
nubia_ClockWidget.apk - clock widget
nubia_Music.apk - nubia music player
nubia_myfile.apk - nubia file manager
nubia_NBSecurity.apk - nubia antivirus and system cleaner
nubia_NotePad_v1.1.5.apk - nubia notepad
nubia_zbiglauncher_v2.0.apk - nubia launcher for old people (everything is biiig)
NubiaPlatLogo_V1.0.0.apk - nubia lanim showing when you tap on NUBIA version in "about phone"
ZAppDataBackup.apk - nubia main app for backup your phone
ZDataBackup.apk - nubia backup app
ZQuickSearchBox.apk - nubia quick search box (if you install GAPPS it contains original google search box)
ZVideo.apk - very basic media player
If you dont use Live Wallpapers you cen delete the main app:
LiveWallpapersPicker.apk
and of course all livepaper apks
BasicDreams.apk
HoloSpiralWallpaper.apk
LiveWallpapers.apk
MagicSmokeWallpapers.apk
NoiseField.apk
PhaseBeam.apk
folder --> /system/preset_apps
TP_360AppStore_1.9.203.apk
TP_360Video_1.2.0_Nubia.apk
TP_BaiduInput_1000541a.apk
TP_baidumap_6.2.0.apk
TP_baiduvideo_5.3.0.apk
TP_gowhere_1044_131118_150501.apk
TP_iReader_2013122410.apk
TP_JdAndroid_2.6.0.apk
TP_QQ_4.2.apk
TP_QRCodeScaner_v1.0.apk
TP_tieba_5.5.2.apk
TP_Weibo_4.0.0_602.apk
TP_weixin_502.apk
Hi, I'm interested in buying this phone.. Could you tell me your first impressions?
It seems very good but I can't see any support for it, even if it has a Snapdragon 400..
Sent from my VOTO X2
DallasCZ said:
ROOT
the only way to root it so far is to run an Chinese exe, which will root your phone and install superuser (chinese one). Then you need to uninstall the superuser and install one from google play.
CWM
so far there is only chinese CWM 6.0.4.6..looking for someone who can make it english.
Click to expand...
Click to collapse
Hi, can you please provide me the exe file to root and explain me the process to root? I would be really grateful for your help! Thanks
I have WCDMA/GSM V5 3G 9180
ROOT CWM
Hello,
i made a simple bat file, which will root your phone, install custom recovery or original recovery.
here is the link: Dallas Google Drive.
you made everything on your own ..i am not responsible for any phone software/hardware damage.
jday17 said:
Hi, I'm interested in buying this phone.. Could you tell me your first impressions?
It seems very good but I can't see any support for it, even if it has a Snapdragon 400..
Sent from my VOTO X2
Click to expand...
Click to collapse
Hi,
there ar ea lot of Chinese phones, this phone is ment to be sell china only.
There are many forums but in Chinese.
I wrote a little review on gizchina.cz (is in Czech language,so use google translator)
TIP
For new users i recommend do this:
-boot your phone and see vhich version of formware you have (latest at this time is 0.50).
-If you have 0.44, then go to dialer and dial ##36. You get to the menu where you can select which server will be used for updates (at this time is 0.50 only for few people for feedback). then go to ybout phone and tap serach for updates and you get the update.
-after update is installed, go to about phone and tap 5times "build number" line , go back and go to "more" and "developer option" and turn on usb debugging.
-launch my root.bat, select root your phone and th ephone will reboot to bootloader and will be rooted.
-now you can install custom recovery (from my bat.file) it is bilangual CWM 6.0.4.9 recovery. Everything works fine as i used it.
-now after root and cwm recovery installed, make backup of your 0.50 rom and then you can proceed to delete bloatware (a lot of bloatware).
for rotted phones with CWM recovery:
if you want to make update from ZTE OTA, you have to load original recovery, the one in my package is not functional with update to 0.50 and above, so you have to flash from CWM recovery this package, then reboot and get the proper stock recovery, which will be functional with the update 0.44-0.50 and later.
DallasCZ said:
For new users i recommend do this:
-boot your phone and see vhich version of formware you have (latest at this time is 0.50).
-If you have 0.44, then go to dialer and dial ##36. You get to the menu where you can select which server will be used for updates (at this time is 0.50 only for few people for feedback). then go to ybout phone and tap serach for updates and you get the update.
-after update is installed, go to about phone and tap 5times "build number" line , go back and go to "more" and "developer option" and turn on usb debugging.
-launch my root.bat, select root your phone and th ephone will reboot to bootloader and will be rooted.
-now you can install custom recovery (from my bat.file) it is bilangual CWM 6.0.4.9 recovery. Everything works fine as i used it.
-now after root and cwm recovery installed, make backup of your 0.50 rom and then you can proceed to delete bloatware (a lot of bloatware).
for rotted phones with CWM recovery:
if you want to make update from ZTE OTA, you have to load original recovery, the one in my package is not functional with update to 0.50 and above, so you have to flash from CWM recovery , then reboot and get the proper stock recovery, which will be functional with the update 0.44-0.50 and later.
Click to expand...
Click to collapse
Thanks for the info! I'm currently updating to 0.5 and will let you know if I manage to root it too.
I`ve read the review and mine phone too has the squeaky back cover. It started squeaky after just few back panel removals. This is not a concern for me, but I wanted to ask you something else: How is you call quality? When I do calls the other side can hear me perfectly but the sound through my ear speaker is muffled and not very clear. Increasing the volume make it even worse. Do you experience such an issue?
-the back cover is really squeaky (i allready ordered another one)
-I am very happy vith the call quality. I had a nexus s whos volume vas up to 100%. Now i am about 60% and everything is loud and clear as i can hear
root and installing cwm is like a charm..i made it in the las 2 weeks (as i own the phone) about 10times
one Question: If you reboot the device do you also have the message "android is upgrading" every time no matter what you do or not do with the system?
DallasCZ said:
-the back cover is really squeaky (i allready ordered another one)
-I am very happy vith the call quality. I had a nexus s whos volume vas up to 100%. Now i am about 60% and everything is loud and clear as i can hear
root and installing cwm is like a charm..i made it in the las 2 weeks (as i own the phone) about 10times
one Question: If you reboot the device do you also have the message "android is upgrading" every time no matter what you do or not do with the system?
Click to expand...
Click to collapse
- I tried updating to 0.5 both through FOTA and with direclty downloaded update from the chinese official site to the sd card, but I always get some error (forgot what it was), will try tomorrow once again.
- My apps are upgrade after each reboot too. I was hoping that 0.5 will fix this issue, but It seems this is not the case.
- I'm on the hunt for a new back cover too, but I will wait for the official blue ones Share your thoughts on the one you purchased after a few days of usage
My only problem with the phone I experience is the bad incoming sound quality during calls. I will have try another sim card.
ps: boy this phone is a beauty
HuKuTo said:
- I tried updating to 0.5 both through FOTA and with direclty downloaded update from the chinese official site to the sd card, but I always get some error (forgot what it was), will try tomorrow once again.
- My apps are upgrade after each reboot too. I was hoping that 0.5 will fix this issue, but It seems this is not the case.
- I'm on the hunt for a new back cover too, but I will wait for the official blue ones Share your thoughts on the one you purchased after a few days of usage
My only problem with the phone I experience is the bad incoming sound quality during calls. I will have try another sim card.
ps: boy this phone is a beauty
Click to expand...
Click to collapse
Hi, can you please tell the name of chinese official site for our phone? thanks!
SITES IN cHINESE LANGUAGE
Hello,
so there are many sites. To see attachments you have to register to the sites, which is a little bit tricky due to instatnt need of translation in the registration process, but it can be done.
official with a lot of new information also from ZTE service:ztehn.com
the best for custom ROM and Recovery (development):anzhi.com
to see anzhi.com you need to add two adress in your windows hosts file see here
also some good information can be found here on myzte.cn
another tip
-If you get the "android is upgrading" on every boot, then you have to uninstall titanium backup, reboot, wait 3 minutes and let the system settle down, then install titanium again, reboot, and its done.
-if you want to restore WIFI access point and passwords form Titanium Backup, use backup from tar file, not from XML!!!
Waiting on a custom rom
Hello everyone,
I used the method I found at needrom.
It did the trick; the device was rooted, gapps installed, an multilangual.
But I didn't manage to install the latest update (50). I thought it was because the device was rooted, so I removed root, whitout succes, I am still not able to install the update.
Also I think the contact manager is buggy; newly added contacts dissapear after rebooting the device, it doesn't matter if I sync the device. I have to import my contacts from my SD card every time this happens.
So, I hope there comes a good custom rom for this device with this excellent hardware! I have Miui unofficiall on my Xiaomi Mi2s, it works like a charm. I hope soon this device appears on the list one of these days
update
-if you installed the ROm from needrom, i think you cannot upgrade to 0.50.
-on www.ztehn.com you can download the full 0.50 rom (only english and chinese language) this rom you can flash.
-contacts: If you are in contacts, press "more" and "advanced" and check the "default storage" it must be set to your google account. Then go back and check "display settings" and check which accounts are to show in contact list.
I had same problem and the problem was, that all new contact automaticly save to local storage and i have the local storage unchecked to display..so i havent seen my newly added contacts!!!
I have same issue
I have same isse. I dont hear anyone. But everyone hear me. i think that built in speaker doesnt work.
ZTE v5 DualSIM v1.06 beta released (4.4.2 + Nubia UI 2.0, package contains new recovery, H106 update package and G050 restore package)
http://pan.baidu.com/share/link?shareid=2878143782&uk=2436317143 Pass: [COLOR=#0640]j7cb
MD5:[/COLOR][COLOR=#0640]3C318AE402AC5424444F5862B540AF2D
[COLOR=#0640]Uploaded to my MEGA acc: link (1.06 unzipped too)
[COLOR=#0640]BETA release [COLOR=#0640]but seems stable (according to chinese forum feedbacks) I will try thi[COLOR=#0640]s next week, when i receive my v9180 2/8G. [/COLOR][/COLOR][/COLOR]
[/COLOR][/COLOR]
I sucessfully installed 1.06 and its looking good so far. The problem Im facing is the "No connection to google servers" error when I try to add my google account. There is no playstore and I tried to manually install it trhough .apk but again no luck. Have you guys managed to run the playstore with this new firmware?
install my gapps package trough cwm recovery.
Hello!
Today I show you How to modify your stock ROM.
In this guide I won't use PC or other software because I want to make this guide easy for all.
Important notes:
For this guide I'll use Samsung Galaxy J3 2016, but similar principles works on other devices.
What you need:
TWRP Recovery for your device.
Root Explorer
Rooted Android Device
And APKs(See later what I think)
Step 1:Activating OEM unlock
Don't skip this step because it's the most important.
Go to Settings and tap About Phone.
Tap 7 times on Build Number and activate Developer Settings.
Enter in Developer Settings and search for OEM UNLOCK, ignore warning and activate them.
If you don't have OEM unclock don't worry you can skip this step.
Step 2: Flashing TWRP Recovery via Odin(Samsung Phones only)
If you don't own Samsung device(or device which can be rooted via KingoRoot) you can skip this step because this step is important for rooting phone.
YOUR WARRANTY IS NOW VOID
Download TWRP recovery for your device and flashable .zip file of SuperSu v2.XX(determine which version is best for your phone).
Run Odin, when Odin starts go to Options tab and de-check Factory Reset Time and Auto Reboot,
then return to main section. And click on AP button and locate your twrp recovery .tar file and than press open. Now turn of your phone and enter in Download Mode hold Power Button + Volume Down Button + Home Button and connect to PC and click on start. When green message PASS apear in Odin you successfully flash recovery.
To restart phone hold power and volume buttons for some seconds or simply remove and return battery
Step 3: Rooting phone
Enter in Recovery Mode(for Samsung device hold power+volume up+home). Swipe slider to allow modification on system partition. Tap on install and find zip file from SuperSU flashable zip and swipe slider to install zip. Wait to installation complete and reboot phone (your phone can reboot some times to complete.
Installing Root Explorer and exploring system/app and system/app-priv
Install Root Explorer and grant Root access.
Now we explore system partition, but before we start in TWRP Recovery make a backup of System partition.
Enter in system/app directory and search for bloatware and other unuseful apps, but be careful what you delete!
Now download apks from apk mirror(clean apks) and place in system/app and when you finished with placing apk files reset phone to Factory Settings.
Tips:
If you have older Android version( <5.0 Lollipop)
download and install XPosed Framework and MonsterUI from Google Play to have Lollipop Notification Bar.
If you have Samsung device with Android Lollipop 5.1.1 or newer go to system/priv-app(or app-priv) and find SecSetupWizard folder delete them and Factory Reset your phone and Voila Setup Wizard is now AOSP.
For Samsung TouchWiz Lollipop ROMs or newer you can download Material Status bar to get AOSP like experience.
If you running Samsung TW Lollipop ROM and want to have AOSP Phone and Contacts app go to system/app-priv(or priv-app) search for SecContacts_L folder and delete them, insert Google Dialer apk(downloaded from apk mirror looks for MINAPI(I USE MINAPI21) and Google Contacts apk and Factory Reset Phone. Now you free from Samsung Phone and Contacts app.
Customizing Stock ROM is so funny and you can make a new ROM(not new but different ).
If I help you Hit thanks button :victory:
And if you have suggestion write in post(s).
Any update on the video ?
Mr.Reticent said:
Any update on the video ?
Click to expand...
Click to collapse
You need to wait to I upload ROM now I'm testing Lineage OS by @djeman
Take a screenshot to I'm not lie
Uploading but it can take a long time...
ROM IS NOW AVAILABLE.
SEARCH ON XDA: J3 RELOADED(ONLY FOR FN MODELS)
-=-=-
mod edit - thread closed as per OP request
I tried to flash MIUI core module using magisk. But MIUI security keeps stopping. Any idea how to fix? Using k33a42. On custom rom (AOSP Extended V4.6)
Hey Bash,
Disclaimer:- once you root your mobile you will lose warranty ad support from the respective companies product you use.
Steps how to install MIUI core in android 7
Download MIUI ROM
Power off your device and restart it into recovery mode.
To turn the phone into recovery mode, press & hold Volume up + Home button (middle button) + Power button simultaneously.
Touch won’t work in Clockworkmod recovery mode (unless you’ve installed touch recovery).
Hence, use the Volume keys for navigation and use the Home button for selection.
In recovery, take a Nandroid backup of your current ROM.
Now, select the ‘wipe data/factory reset option using volume keys.
On the next screen press the Yes option to start the wiping process.
Return to the main menu and select the Advanced option.
On the next screen select the Reboot Recovery option.
This will restart your (x)andorid phone back into recovery.
Click on the ‘install zip from SD card option from the main menu.
Furthermore, select the ‘choose zip from SD card option.
This will display the data present on your mobile.
Simply select the downloaded MIUI 7.zip file.
On the next screen select the ‘Yes’ option to start the ROM flashing process.
Similarly, flash the Google Apps zip file as you have installed the MIUI ROM.
Do not wipe data and cache partitions after installing the GApps file.
Finally, click on the ‘reboot system now option to restart your device.
Enjoy your phone has been successfully installed MIUI7. In my opinion, you should move with the latest android and MIUI version it will fix your all bugs and the newly updated android has many new features that 7 does not have. If you have still an issue then you need to talk with a mobile developer or you should visit your nearest mobile service shop. Try to contact a web app development company that is also an expert in various mobile fields.
Thanks
Katherine272 said:
Hey Bash,
Disclaimer:- once you root your mobile you will lose warranty ad support from the respective companies product you use.
Steps how to install MIUI core in android 7
Download MIUI ROM
Power off your device and restart it into recovery mode.
To turn the phone into recovery mode, press & hold Volume up + Home button (middle button) + Power button simultaneously.
Touch won’t work in Clockworkmod recovery mode (unless you’ve installed touch recovery).
Hence, use the Volume keys for navigation and use the Home button for selection.
In recovery, take a Nandroid backup of your current ROM.
Now, select the ‘wipe data/factory reset option using volume keys.
On the next screen press the Yes option to start the wiping process.
Return to the main menu and select the Advanced option.
On the next screen select the Reboot Recovery option.
This will restart your (x)andorid phone back into recovery.
Click on the ‘install zip from SD card option from the main menu.
Furthermore, select the ‘choose zip from SD card option.
This will display the data present on your mobile.
Simply select the downloaded MIUI 7.zip file.
On the next screen select the ‘Yes’ option to start the ROM flashing process.
Similarly, flash the Google Apps zip file as you have installed the MIUI ROM.
Do not wipe data and cache partitions after installing the GApps file.
Finally, click on the ‘reboot system now option to restart your device.
Enjoy your phone has been successfully installed MIUI7. In my opinion, you should move with the latest android and MIUI version it will fix your all bugs and the newly updated android has many new features that 7 does not have. If you have still an issue then you need to talk with a mobile developer or you should visit your nearest mobile service shop. Try to contact a web app development company that is also an expert in various mobile fields.
Thanks
Click to expand...
Click to collapse
Thank you so much! But there is no miui custom rom for Lenovo k33a42. Do you have any link?
Btw, I saw in GitHub that we can use miui apps by flashing miui core from magisk. I did flash and also Flashed miui security zip. After reboot app appears but it crashes automatically..