Related
Updates
10/1/2011 - Added 00remounti9001 to remount the major partitions to noatime and disabled barriers for as well as delayed journaling to every 60 seconds (as opposed to 5) to /data, /persist, /cache. Added Acid Tweaks - Removed Useless Stuff i9001.zip to remove journaling from /cache and /system (It's safe). Also added JournalingOn.zip to revert back the two partitions to being journaled.
For the 00remount script, here's the how to:
0. Wait till Android finishes loading everything.
1. Install Script Manager from Market
2. Point script manager to the script you placed in the sdcard.
3. Run as root.
4. Do this at every boot, as mount points are reset to its default as set by the type of your lagfix. Voodoo (from what I am using will set barriers for /data and atime for every mount point except /system, /data, /cache, /dbdata which puts a slight risk at your disk for using atime.
5. You can add a widget to your home screen for the script so that you can
activate it easily.
The other two are CWM zips. You should know how to flash CWM zips right?
Introduction
I've made a Definite Guide on Android thread for i9000 that focuses on a few optimizations/scripts I've picked up over the months I've spent on XDA. I truly enjoyed sharing my knowledge with the i9000 community and since the tips/guide/scripts can also be applied here (save some exceptions that I would list down below),I would like to share this with the Captivate community too.
Exceptions
Take note that the guide is primarily for i9000 units. There are a few differences I can note here that you should be aware of:
1. The guide points out some kernels/ROMs that are for i9000. Hence the phones you are using may have different ROMs/kernels that may or may not correlate with the one in the guide.
2. The guide also mentions some apps/tweaks that are particularly alien to your unit and you may have never encountered it in your use of your phone or in XDA. Please ignore them for now, I'll make an effort to make the guide compatible in the future (with feedback from you guys of course )
3. Journaling scripts that are attached like the JournalingOn.zip and Acid Tweaks - Removed Useless Stuff and 00remount may not work well with your unit or it may completely brick it. I don't know this, but if you can post your mount partition configuration, I am willing to make the scripts work for you. You only have to type "mount" on your Terminal Emulator and provide the output to me, and I'll provide the rest. Zach's script however, have high compatibility towards a lot of phones, and thus can be used for your unit. Take note that there is a slight risk that it won't work well. If it doesn't, please post your problems here, and I'll try to fix it. Hence, it's best that you make a nandroid backup before attempting to use any tweaks here.
3. I've compiled a guide on a few notable tweaks in XDA here: LINK. If you would like me to evaluate scripts/tweaks/anything that you do not understand due to their terms being alien to you, I'll be glad to explain it here
Guide
You can refer to the guide here:
LINK
Hi pikachu!
I've made a screenshot of the terminal output after entering the mount command. Hope it provides you the needed informations!?
reneph said:
Hi pikachu!
I've made a screenshot of the terminal output after entering the mount command. Hope it provides you the needed informations!?
Click to expand...
Click to collapse
Thank you
I'll get to work on the scripts. Give me an hour or two
pikachu01 said:
Thank you
I'll get to work on the scripts. Give me an hour or two
Click to expand...
Click to collapse
Updated the scripts. Please read my guide before flashing any of those zips/scripts to know about its risks.
I am not responsible for any damages/bootloops if you did not read the guide before flashing those scripts/zips.
UPDATE 10/1/2011 - Added 00remounti9001 to remount the major partitions to noatime and disabled barriers for as well as delayed journaling to every 60 seconds (as opposed to 5) to /data, /persist, /cache. Added Acid Tweaks - Removed Useless Stuff i9001.zip to remove journaling from /cache and /system (It's safe). Also added JournalingOn.zip to revert back the two partitions to being journaled.
For the 00remount script, here's the how to:
0. Wait till Android finishes loading everything.
1. Install Script Manager from Market
2. Point script manager to the script you placed in the sdcard.
3. Run as root.
4. Do this at every boot, as mount points are reset to its default as set by the type of your lagfix. Voodoo (from what I am using will set barriers for /data and atime for every mount point except /system, /data, /cache, /dbdata which puts a slight risk at your disk for using atime.
5. You can add a widget to your home screen for the script so that you can
activate it easily.
First of all, thanks for the work.
I have tried to execute the remount-script using the script manager as root as you mentioned, but something fails. When running the script it outputs "mount: No such file or directory, mount: Invalid argument" and then the predefined echos of the script.
I had to remove following lines of code to get an output without the mount-errors:
mount -o noatime,remount,rw /mnt/.lfs /mnt/.lfs;
mount -o noatime,remount,rw /sys/kernel/debug /sys/kernel/debug;
Click to expand...
Click to collapse
more scripts and tweaks!
http://forum.xda-developers.com/showthread.php?t=1227269
reneph said:
First of all, thanks for the work.
I have tried to execute the remount-script using the script manager as root as you mentioned, but something fails. When running the script it outputs "mount: No such file or directory, mount: Invalid argument" and then the predefined echos of the script.
I had to remove following lines of code to get an output without the mount-errors:
Click to expand...
Click to collapse
Thanks for the heads up. I forgot to remove those lines actually. I reupload the script with those two lines remoevd.
sakindia123 said:
more scripts and tweaks!
http://forum.xda-developers.com/showthread.php?t=1227269
Click to expand...
Click to collapse
Thanks for the link. Yes, I've read this one before. My guide would explain more about what some of the tweaks do, and the script incorporates more than the link that you provided. You can edit the script and take a look if you want
is this working?
larry200ro said:
is this working?
Click to expand...
Click to collapse
Which tweak are you specifically asking about?
They should work provided you read the guide to know what those tweaks are
can i use this in my rom?thanks
sakindia123 said:
can i use this in my rom?thanks
Click to expand...
Click to collapse
Why not?
Let me know how good it is working for you. Remember to read the guide, as the scripts might not work well with other scripts (if your ROM also implements other scripts)
pikachu01 said:
Which tweak are you specifically asking about?
They should work provided you read the guide to know what those tweaks are
Click to expand...
Click to collapse
Honestly, I am at work now, I tried to read some things really quickly from your guide but I think that this is to technical for me. In a few words can you please describe what are they doing? I own a i9001 with Kernel 2.6.35.7-perf [email protected] #1 and build number gingerbread.xxkg1 android 2.3.3.
Sorry if my english is not to good, I am at work , have no time to concentrate, I am Romanian
larry200ro said:
Honestly, I am at work now, I tried to read some things really quickly from your guide but I think that this is to technical for me. In a few words can you please describe what are they doing? I own a i9001 with Kernel 2.6.35.7-perf [email protected] #1 and build number gingerbread.xxkg1 android 2.3.3.
Sorry if my english is not to good, I am at work , have no time to concentrate, I am Romanian
Click to expand...
Click to collapse
Umm, if you only want to use the scripts, you could scroll down to Zach's scripts and 00remount (Hint: They are in quoted text form). They are pretty short and simple to read. All the others in the guide would reinforce the things that are explained in there. If you don't understand something in the guide, post it here, and I'll offer up a simpler more laymen explanation of it
And you'll need a custom kernel with init.d support if you want to use the scripts.
pikachu01 said:
Umm, if you only want to use the scripts, you could scroll down to Zach's scripts and 00remount (Hint: They are in quoted text form). They are pretty short and simple to read. All the others in the guide would reinforce the things that are explained in there. If you don't understand something in the guide, post it here, and I'll offer up a simpler more laymen explanation of it
And you'll need a custom kernel with init.d support if you want to use the scripts.
Click to expand...
Click to collapse
Sorry but you lost me in the bold section. Where do I get a custom kernel with init.d support? I am searching for a month now for a custom kernel/custom rom/custom anything for my phone but found nothing than the successfull rooting guide in this forum.
Am I so stupid?
pikachu01 said:
And you'll need a custom kernel with init.d support if you want to use the scripts.
Click to expand...
Click to collapse
But not for the remount-script!?
Anyways, is there an existing custom kernel for the phone at all?
larry200ro said:
Sorry but you lost me in the bold section. Where do I get a custom kernel with init.d support? I am searching for a month now for a custom kernel/custom rom/custom anything for my phone but found nothing than the successfull rooting guide in this forum.
Am I so stupid?
Click to expand...
Click to collapse
Ahh, it appears that i9001 doesn't have a custom kernel If supercurio or chainfire is free, they could patch the initramfs with theirs and publish it here. I'm not an expert in initramfs and I don't have this phone
reneph said:
But not for the remount-script!?
Anyways, is there an existing custom kernel for the phone at all?
Click to expand...
Click to collapse
The remount script will always work, yes with Script Manager. No, I can see that i9001 doesn't have a custom kernel for it. Too bad
Actually, even without init.d support, you could use Script Manager to launch the scripts at boot. The only thing is that the screenstate_scaling would need the Script Manager to be on all the time, which will drain more battery than save it.
pikachu01 said:
Actually, even without init.d support, you could use Script Manager to launch the scripts at boot. The only thing is that the screenstate_scaling would need the Script Manager to be on all the time, which will drain more battery than save it.
Click to expand...
Click to collapse
So, you are saying that it's better not to use any scripts until a custom Kernel will appear?
larry200ro said:
So, you are saying that it's better not to use any scripts until a custom Kernel will appear?
Click to expand...
Click to collapse
You can use the scripts with Script Manager. A custom kernel only makes it easier to apply the scripts.
pikachu01 said:
You can use the scripts with Script Manager. A custom kernel only makes it easier to apply the scripts.
Click to expand...
Click to collapse
Ok, This I understood very well but, as you said before, this will need Script manager to be running all the time which will result in more battery spent.
Isn't the purpose of all tweaks/scripts to improve performance without lose of battery life and the phone to run the applications that you need and freeze/uninstall those you never use?(I've uninstalled the applications that I don't need with Titanium Backup and I have improved my battery life significantly).
Thanks very much pikachu for all the scripts and for the good work but I think this is not worth it because 1. galaxy s plus i9001 has a good 1.4Ghz processor and runs almost anything perfect. 2. You can safely improve the battery time with a simple software available on the market for free without risking with scripts.
Many thanks again, if you need any information from my phone for development purposes just let me know. I am willing to help
i want to create a rom for i9001..i have already started a thread for this.
and init.d will be one of the first things i would do!
all ur scripts will load automatically at startup!
Hi there,
I am fairly new to custom ROMs etc and recently installed LeeDroid 4.3.0 successfully. However, I also wanted to try out a custom ROM and installed Faux' kernel too (mainline).
Battery drain became a lot better, but there's an optional feature to under voltage the CPU. According to the guide in the thread, I have to put
Code:
echo "-25000" > /sys/devices/system/cpu/cpufreq/vdd_table/vdd_levels
somewhere. Can someone tell me in where I have to put this in detail? Any other things I should take care of / should be aware of?
If this topic was discussed already (sure it was), please don't hesitate to link me to it, I just couldn't find anything via forums search.
Thanks!
You can run it with a terminal emulator directly on your phone or through adb/shell on your pc.
Either way, it's not going to stick and you should repeat the operation after every reboot if you want to keep the UV.
You can add that line to a script, though, so that it is executed automatically after every boot.
I usually add that line to the init.post_boot.sh script in /system/etc (between the other MSN8660 tweaks). The alternative is adding a file in the init.d folder.
nTraum said:
Hi there,
I am fairly new to custom ROMs etc and recently installed LeeDroid 4.3.0 successfully. However, I also wanted to try out a custom ROM and installed Faux' kernel too (mainline).
Battery drain became a lot better, but there's an optional feature to under voltage the CPU. According to the guide in the thread, I have to put
Code:
echo "-25000" > /sys/devices/system/cpu/cpufreq/vdd_table/vdd_levels
somewhere. Can someone tell me in where I have to put this in detail? Any other things I should take care of / should be aware of?
If this topic was discussed already (sure it was), please don't hesitate to link me to it, I just couldn't find anything via forums search.
Thanks!
Click to expand...
Click to collapse
you could just get System Tuner Pro from the market and UV that way
Thanks, got it with Grandelama's method.
Grandelama said:
You can run it with a terminal emulator directly on your phone or through adb/shell on your pc.
Either way, it's not going to stick and you should repeat the operation after every reboot if you want to keep the UV.
You can add that line to a script, though, so that it is executed automatically after every boot.
I usually add that line to the init.post_boot.sh script in /system/etc (between the other MSN8660 tweaks). The alternative is adding a file in the init.d folder.
Click to expand...
Click to collapse
how did u put it in the init.post_boot.sh?
i cant do that cuz cannot write to that
and writing tool have super user permissions,
that file cannot be editing
or can? if - how?
Hi there
I got droidwall running on the SGY.
Please first read the whole post. I add changes at the end of it.
Here's what I did:
1. follow this great tut from irfanbagus. Thanks a lot irfanbagus!
2. After running "make bcm21553_totoro_05_defconfig", set this in .config:
CONFIG_IP_NF_TARGET_REJECT=y
CONFIG_NETFILTER_XT_MATCH_OWNER=y
and continue irfanbagus's steps
3. Install the new boot.img, e.g. via mai77's method as shown here
4. Profit! (as in: use droidwall )
Notes:
Alternatively the changes in .config could be set in cm21553_totoro_05_defconfig or via make menuconfig
If you don't have your boot.img as a normal file, run this in adb, then pull the file:
dd if=/dev/block/bml7 of=/data/local/boot.img
I was surprised that there was no such modified kernel till now. Maybe this is because the TARGET_REJECT option is essential but only XT_MATCH_OWNER is largely discussed when dealing with droidwall.
See attachment (mikstev_SGY_Kernel_netfilter_for_droidwall_boot.img.zip) for a boot.img with only these modifications.
Please test and report. I only tested blacklist/whitelist mode with Google Play blocked/allowed on Wifi connection, but it worked.
Edit 1: I've added the necessary (and probably some more) modules so that droidwall's logging works. Use the second attached file instead the first one.
Here are the changes I made, compared to normal .config:
CONFIG_NETFILTER_NETLINK=y
CONFIG_NETFILTER_NETLINK_LOG=y
CONFIG_NETFILTER_XT_MATCH_OWNER=y
CONFIG_IP_NF_TARGET_REJECT=y
CONFIG_IP_NF_TARGET_LOG=y
CONFIG_IP_NF_TARGET_ULOG=y
I guess the first two aren't necessary but I didn't bother to check every single module if it's the correct one which droidwall needs for logging. However this shouldn't matter anyway. See mikstev_SGY_Kernel_netfilter_for_droidwall_with_log_boot.img.zip
Edit 2: Due to request I've added init.d support to the latest release. Thanks irfanbagus! See mikstev_SGY_Kernel_droidwall_initd_boot.img.zip
Edit 2.5: Seems only the following modules are required but that only as a side note:
CONFIG_NETFILTER_XT_MATCH_OWNER=y
CONFIG_IP_NF_TARGET_REJECT=y
CONFIG_IP_NF_TARGET_LOG=y
Edit 3: New method for adding init.d support to a (newest) boot.img, with kernel modules for droidwall (+logging) and init.d scripts to load these modules. Please read the readme, if you have questions, post here. Special thanks to irfanbagus See mikstev_add_initd_to_boot.img__kernel_modules_initd_scripts_for_droidwall.zip
Edit 4: Thanks to an idea by irfanbagus and another tutorial to include init.d support by kurotsugi, here's another release. Adding init.d support is now easier with kurotsugi's method plus there's a update.zip (modules_droidwall_signed.zip) which does the other steps for you (copying the modules, init.d scripts and applying the correct permissions for these files). NOTE: this update.zip is yet untested. If you test it please report. See mikstev_add_initd_to_boot.img__kernel_modules_initd_scripts_for_droidwall_v2.zip
Edit 5: The update.zip from edit 4 seems to work. If you're using a kernel with init.d support you only need to install the update.zip and it should work fine.
good job. i know droidwall depend on other kernel features beside CONFIG_NETFILTER_XT_MATCH_OWNER. since i don't have plan to use droidwall, i don't bother to find it.
Profit indeed! It works! Good job, mikstev! I was able to block dolphin HD on my phone just to test if it works and it did, much to my delight!
And to irfanbagus as well for that wonderful guide on how to compile a kernel.
Great job, guys!
Now let's hope that all the other kernel developers include this small bit of configuration in their builts
finally! ive been waiting for this for ages. thank you very muchhhh!
Sent from my GT-S5360 using xda premium
Logging doesn't work yet. I'll try the solution from highlandsun: http://forum.xda-developers.com/showpost.php?p=11110889&postcount=357 tonight and upload new kernel if successful.
No need for so much hassel
Just use "lbe privacy guard" (free in store) it has much more features than droidwall and it doesnt require any special kind of kernel.
Y u no press "thanks"!?
Sent from my GT-S5360 using XDA
Ok, logging works now, I'll upload the new kernel. See first post.
devilrulz4ever said:
No need for so much hassel
Just use "lbe privacy guard" (free in store) it has much more features than droidwall and it doesnt require any special kind of kernel.
Y u no press "thanks"!?
Sent from my GT-S5360 using XDA
Click to expand...
Click to collapse
It seems that there're at least some people who see this differently. Here're some of my reasons, why I prefer droidwall over LBE Privacy Guard:
- it's a good and easy to use firewall. Not more, nor less. That's what I want.
- no "hassel" (to use your words) with resticting internet access of "trusted" apps
- I did not find a way in LBE to block LBE from using internet. In the iptables rules created by Droidwall I can clearly see that droidwall is not allowed = blocked
@mikstev: I'm just curious...is it based on sgy's newest kernel?
I think so, the source code is the one mentioned in irfanbagus' post (update2) which I linked above.
nice...I can integrate dualboot and data-2sd mod into this kernel easily. thx
i got other option to make droidwall work.
on init.rc i added this line:
service netfilter /system/bin/iptables
disabled
oneshot
this also work with avast firewall..
gear12 said:
i got other option to make droidwall work.
on init.rc i added this line:
service netfilter /system/bin/iptables
disabled
oneshot
this also work with avast firewall..
Click to expand...
Click to collapse
Can anyone confirm this? I can't see how this could replace the missing kernel modules.
mikstev said:
Can anyone confirm this? I can't see how this could replace the missing kernel modules.
Click to expand...
Click to collapse
nope. iptables only a user space application that depend on kernel features. and you can't call iptables without command/params.
the firewall works great, also, I can see the logs but after disconnecting from the internet and a few minutes the log is empty again, is this normal or a bug?
off topic:
and can I make a request? can you make the your boot.img support init.d as well? please...
Adam_Blade said:
the firewall works great, also, I can see the logs but after disconnecting from the internet and a few minutes the log is empty again, is this normal or a bug?
Click to expand...
Click to collapse
Yep, I noticed this too. The droidwall source seems ok at first glance and I don't think it's related to the netfilter modules etc. My guess would be that it's dmesg's fault, maybe the log is truncated or something but this is just speculation. I'll investigate in this in a few days. Maybe someone else knows why this happens?
Adam_Blade said:
and can I make a request? can you make the your boot.img support init.d as well? please...
Click to expand...
Click to collapse
Sorry, I currently don't have the necessary skills, so if you're looking for a quick solution you might better ask someone else for help. (Especially since there're already kernels with this feature and including the modifications for netfilter/droidwall should be trivial). However as I wanted to build up my knowledge regarding android/kernel development anyway, I'll try to add this feature one time, but that surely would take >1 week.
Regarding dmesg: the buffer size is set by CONFIG_LOG_BUF_SHIFT=19 which means 2^19 Bytes = 512KiB. I'll check later if this relatively huge size is really used up.
@mikstev: make init.d support kernel is easy. we only have to add a few script inside init.rc file. we can do it easily by using dsixda's kitchen or put the script manually. you can see my modified init.rc here http://www.mediafire.com/?cc1kg8s7cx27onb
I believe the script that have to be added is
service sysinit /system/bin/logwrapper /system/xbin/busybox run-parts /system/etc/init.d
disabled
oneshot
Just to get sure: the init.rc which needs to be modified is the one in the initial ramdisk and not in the kernel (zImage), right?
I wrote this guide for originally in elk759's JB CM10 thread, but with some modifications it works with every ROM and every phone.
I thought other guides were too hard to understand so I concluded all neccessary information and nothing more.
This guide is for Windows, because it uses a Windows tool to make the process MUCH easier. This only affects the modding of services.jar, so look at the original Supercharger thread for instructions withot the Windows tool.
Here are the benefits of using SUPERCHARGER, I cn approve that it works, it's faster, more apps can run and no launcher redraws!
___________________________________________________________________________
Sources:
http://forum.xda-developers.com/showpost.php?p=12058585&postcount=1
http://forum.xda-developers.com/showpost.php?p=18703418&postcount=5021
zeppelinrox said:
What's it do?
It makes your phone FAST... super snappy with better multitasking!
It rearranges and fixes the OOM Groupings and Priorites and lowmemorykiller values.
So basically, it's a COMPLETE MEMORY MANAGEMENT FIX!
It's the ONLY one of it's kind
NO LAUNCHER REDRAWS, faster than ever, multitasking is better... why?
Because it works with the lowmemorykiller and letting it work the way it's meant to work.
Also, because of the rearrangement, it works the same on all roms!
The problem with using minfree tweakers like AMM or AKMO is that it doesn't work the same on all roms.
Secondary apps may be in slot 3 on some roms but in slot 5 in others!
That's why you hear people comment "I tried AKMO but it didn't do anything..."
Most likely it didn't do anything because the apps weren't sitting where they were expected to be.
So fasten your seat belts and enjoy the ride!
Click to expand...
Click to collapse
zeppelinrox said:
And -=Maximum Overdrive=- was born!
Upside: You can run up to 70 apps if you have enough RAM.
Downside: NONE
Click to expand...
Click to collapse
zeppelinrox said:
The Kick Ass Kernelizer
What Does The Kick Ass Kernelizer Do?
Memory Management++
MFK Calculator Info - explanation for vm.min_free_kbytes
LinuxInsight - The /proc filesystem documentation (Fantastic!)
XDA [REF] Startup script speed tweaks OP by hardcore
XDA Speed up your system with the noop scheduler
TCP Speed & Security
Security and Hardening the TCP/IP stack to SYN attacks
Click to expand...
Click to collapse
zeppelinrox said:
The 3G TurboCharger
In case of connection issues, see the notes in the 3G TurboCharger section at the top of /system/build.prop!
Homework/Background Info... see the folllowing links for resources used.
XDA Thread 1
XDA Thread 2
XDA Thread 3
Wi-Fi AfterBurner.
XDA Thread (Faster WIFI - N Standard Enabling)
The 3g build.prop tweaks aren't really anything new... but I did put a new spin on it! ;^]
You can find various individual configurations but as far as I know, my script is the only one that lets the user choose from more than one configuration.
Click to expand...
Click to collapse
___________________________________________________________________________
IF YOU HAVE ANY PROBLEMS, LOOK FIRST AT THE Q&A BELOW!
1. Prerequisites:
SuperCharger_Starter_Kit_xxx.zip (contins busybox, sqlite and zipalign)
[*]V6_SuperCharger_for_Android-Update9_RC11_xxx.sh.pdf
Script Manager for starting scripts (on first run enable root browse AND run every script with su rights, the skull and bones symbol)
ES File Explorer (with root rights in settings->root management)
optionally: Terminal Emulator
Recommended for everyone and REQUIRED for 4.0+ Roms:
pepcisko's Windows tool for patching services.jar
Place the V6_Supercharger script and the Supercharger_Starter_Kit.zip content to "/sdcard/V6"
Place the Windows tool somewhere on your Hard Drive
Install the required apps
2. Installation of Starter Kit:
Start SManager and confirm root rights when browsing
go to sdcard/V6/1_SuperCharger_Starter_Kit and click on StartMeUp.sh
select the SU button (skull + bones) and RUN it as script and follow the instructions (install at least busybox for being safe that everything works)
3. Patching services.jar
Background information (could be very useful):
Patching the services.jar gives you the multitasking mod. Apps shouldn't restart all the time, they will stay in RAM as long as they can.
Patching the services.jar is REQUIRED for Android 4.x.x, but you don't have to use multitasking mod.
For the other Android versions it isn't required, you only need this if you want to have multitasking mod, too.
If you have Sense 4.0+ and want multitasking mod, you have to follow this, more complex tutorial.
But you can also use this method, but your visible app limit stay at 8 Apps, instead of 50!
extract the Windows tool and launch it
You can choose between online mode (phone drivers needed) or offline mode, I'll explain offline mode:
make sure you have root rights in ES Explorer and that you mount system as R/W (read/writable)
copy the services.jar from /system/framework to your SD, and connect your phone to PC
move the services.jar to the framework folder of the Windows tool directory
in the windows tool specify your Android version + if the rom is odexed/deodexed
now press "enter" -> "y" for supercharge -> "enter" for die die-hard launcher -> "enter" -> "y" for multitasking -> "enter" -> "y" to delete temporary files
You have patched the services.jar, now you have two options (both files are in "dist" directory):
Place the update-signed.zip on sdcard and install it via recovery
OR
Place the modded services.jar (and if odexed rom the services.odex too) to /system/framework and overwrite. Then you have to set owner and permissions:
In Terminal Emulator
su
(confirm SuperUser Request)
busybox mount -o remount,rw /system
cd /system/framework
chown 0.0 services.jar
chmod 644 services.jar
Now go into recovery (or stay there after flashing update-signed.zip) and wipe cache & dalvik cache.
On your next reboot apps should be optimized.
4. Supercharger Installation
Remember: I can't promise, that the guide is always up to date. So it could happen that after an update of the script, the option numbers are different. Look at the text on the right side of the option
start the /sdcard/V6/V6_SuperCharger... script with SManager with SU rights
follow the instructions of driver options: You will be asked for Scroll Speed but also various tweaks which can improve the performance
The script calculates the preferred FreeMem size, you can use them or set your own prefered size:
After you have declined to use the calculated option you are in Driver's Console, you can choose between 33 options.
The Options 2 to 9 set the MinFree size, for the different Ram Size of the devices.
For the Desire I recommend option 6 which is called "balanced". You can try a lower or a higher option, too.
Lower values are better for Multitasking, higher values are better for the speed on the visible app.
go back to driver options and type 21 for Nitro Lag Nullifier, confirm with N (could be unstable, you don't have to use this)
After you are finished press option 17 for Engine Flush and after that option 32 for SuperClean& Restart
After the restart you should open SManager again and navigate to /system/etc/init.d, click on S99SuperCharger and enable SU + Run on Boot.
Press Save. This should avoid issues if you want to launch Supercharger Script again (for me it worked without doing that)
Widgets for easy and fast freemem change:
For compairing settings, you can make widgets, settings will be changed instantly:
- you have to select the option you want to use as a widget (e.g. option 5 of supercharger) one time in V6_Supercharger script
Your selected options will appear as a small script in sdcard/V6_Supercharger/PowerShift_Scripts
- long press on home screen, click on Widgets and select SManager
- choose the script you want to use (e.g. 512HP_UnLedded...)
Q&A Supercharger
Q: Supercharger says "sorry, your rom wipes service entries on boot". Is it an issue?
A: No you can ignore it. You'll stay supercharged. (thx to abelle_abelle for the hint)
Q: Supercharger says that I'm only 75%/50% supercharged. What is the reason?
A: Propably the services.jar hasen't been patched right. Check if the services.jar is replaced and if the owner and the permissions are right. Try it out with offline mode in the Windows tool.
Q: Do I have to patch the services.jar again after rom update?
A: If you flash the rom you have to replace the original services.jar again. I don't know if you can use the previous patched services.jar.
Q: Do I have to run the whole script again after a rom update?
A: You have to run the Supercharger script again, but it has stored the last settings and can restore them. Then you have to Wipe Cache & Dalvik, reboot and set /system/etc/init.d/S99SuperCharger to run with SU rights + at boot.
Q: Did my settings stick?
A: If Supercharger says "100% supercharged" everything should be fine. If you think there is something wrong, because of a particular message paste the log text in pastebin.com and give me the link in your post.
Q: Do I have to install the Supercharger StarterKit?
A: No, you cann try it without this first if you want. BUT some busybox versions doesn't work with Supercharger (everything below 1.16.2 and even some versions above 1.16.2.
The StarterKit installs a recommended version.
Q: My phone is getting slower from time to time.
A: This can happen if you don't reboot often (1 or 2 days). The cache is growing and there is less and less RAM.
If you don't want to reboot all the time you can make the EngineFlush in V6_SuperCharger (option 17) and a script will be created (!FastEngineFlush.sh). You can make a widget for it after you set it as favorite or launch it normally in Script Manager.
A more detailed guide about making widgets is written above.
Q: Everythings (apps and launcher) stucks after NitroLagNullifier/V6 Supercharger installation. What can I do?
A: The user abelle_abelle had this issue. He had to hard reset his device (hard reset wipes your partitions -> deletes your data) and had to reinstall the rom.
Q: Are there any possibilites to make my rom even faster?
A: Yes, with KickAssKernelizer (KAK):
http://forum.xda-developers.com/showpost.php?p=32508611&postcount=35
Maybe I will write a bit more detailed guide for this. You can see what it does at the benefits of Supercharger at the top of my first post.----------------------------------------------------------------------------------------------------------------------------------------------------------
It took me long to test and to write please give a Thanks if I helped you
Also thank the creator of the scripts (check links)
Reserved for possible addition and Q&A
Have been using this for some time, and I can confirm it works.
Sent from my toaster.
I'm stuck in the CM logo screen after installing service.jar (online mode) and wiped davlink and cache.
aledex said:
I'm stuck in the CM logo screen after installing service.jar (online mode) and wiped davlink and cache.
Click to expand...
Click to collapse
Which Rom you are using?
Androidmarketuser said:
Which Rom you are using?
Click to expand...
Click to collapse
I'm sorry, I thought I edited the post. I'm using Elk's CM10 for Desire.
After trying several times to wait after having wiped cache and davlink (and fixed permissions) I re-flashed the rom and tried to apply the superchager script.
Problem 1: not enough spaces on the system (I'm using INT2EXT)
Problem 2: supercharger only at 50%
Problem 3: Apex launcher not recognized
Should I try to re-do everything, maybe this time with the offline method? But how to avoid the system space problem?
aledex said:
I'm sorry, I thought I edited the post. I'm using Elk's CM10 for Desire.
After trying several times to wait after having wiped cache and davlink (and fixed permissions) I re-flashed the rom and tried to apply the superchager script.
Problem 1: not enough spaces on the system (I'm using INT2EXT)
Problem 2: supercharger only at 50%
Problem 3: Apex launcher not recognized
Should I try to re-do everything, maybe this time with the offline method? But how to avoid the system space problem?
Click to expand...
Click to collapse
First off, I used it for CM10 too but without int2ext.
The reason for 50% is propably the unpatched service.jar(at beginning I had this issue too)
First, I would try to use the offline mode, the utility propably hasn't patched anything so try if it's working by manual way.
Just put the service.jar on PC, patch it and replace it. Then start the Supercharger V
script gain and it should be 100%.
otherwise do that:
On your SD Card there should be a Supercharger.html with a "log" or sth like that, please send it to me.
Additionally check if there is a "V6 Supercharger" folder on your SD, created by the script.
And check the output of the Windows tool! Be sure you have phone drivers on your PC and your phone is connected without SD Card Read if you use online.
-------------------------------------------
The space on system shouldn't be a problem, you have to use at least 250mb system (so stock hboot), int2ext only mounts /data on ext, so as I understood it is used for fatsys hboots which have 450mb system and NO space for data...
Why do you think that the space is a problem? Where did you notice it?
The APEX problem can be discussed after getting the rest work...
Please give feedback whether it worked or not
Androidmarketuser said:
First off, I used it for CM10 too but without int2ext.
The reason for 50% is propably the unpatched service.jar(at beginning I had this issue too)
First, I would try to use the offline mode, the utility propably hasn't patched anything so try if it's working by manual way.
Just put the service.jar on PC, patch it and replace it. Then start the Supercharger V
script gain and it should be 100%.
otherwise do that:
On your SD Card there should be a Supercharger.html with a "log" or sth like that, please send it to me.
Additionally check if there is a "V6 Supercharger" folder on your SD, created by the script.
And check the output of the Windows tool! Be sure you have phone drivers on your PC and your phone is connected without SD Card Read if you use online.
-------------------------------------------
The space on system shouldn't be a problem, you have to use at least 250mb system (so stock hboot), int2ext only mounts /data on ext, so as I understood it is used for fatsys hboots which have 450mb system and NO space for data...
Why do you think that the space is a problem? Where did you notice it?
The APEX problem can be discussed after getting the rest work...
Please give feedback whether it worked or not
Click to expand...
Click to collapse
Here's my problem:
1 - Installation of starter kit:
http://i50.tinypic.com/dqp5qf.png
2 - Patch of services.jar went ok with offline mode, but when I try to change permissions
http://i45.tinypic.com/34drlog.png
(this problem is obviously related to point 1)
Supercharger.html in attachments
aledex said:
Here's my problem:
1 - Installation of starter kit:
http://i50.tinypic.com/dqp5qf.png
2 - Patch of services.jar went ok with offline mode, but when I try to change permissions
http://i45.tinypic.com/34drlog.png
(this problem is obviously related to point 1)
Supercharger.html in attachments
Click to expand...
Click to collapse
Do you have stock hboot?
Try to delete some unnecessary preinstalled apps with file explorer.
(I search for some which you could delete...)
Edit: in system/app/ you can delete at least Calenar.apk, ES File Explorer.apk and Email.apk (after backup I think you can delete Gallery2.apk too, don't know how this affects on camera)
This should free at least 4mb and should be enough.
The file was just a help file and not a log, sorry for the mistake, thought it would create a og, but you have showed me the eroor with the pics...
Hey mate can you make a youtube video showing the steps. I understand better with visuals, and thanks for sharing.
Sent from my HTC Desire using xda app-developers app
Androidmarketuser said:
Do you have stock hboot?
Try to delete some unnecessary preinstalled apps with file explorer.
Click to expand...
Click to collapse
Yes I have stok hboot, and this is the first time I try to install V6 on a JB rom.
Concerning the lack of space I've done like you said, thank you!... BUT when I try to install binay 3.1 (which should fix the segmentation faults) it points out that it's only for ICS and aborts the installation. So I fixed the permission manually.
Now I'm going to check the rest and see what happens.
Fixed permission, flashed update-signed.zip, wiped davlink and cache, rebooted and... well, after HTC logo the screen turned off and only the hardkeys were illuminated
I'm going to flash the rom again and start from the beginning for the third time.
aledex said:
Yes I have stok hboot, and this is the first time I try to install V6 on a JB rom.
Concerning the lack of space I've done like you said, thank you!... BUT when I try to install binay 3.1 (which should fix the segmentation faults) it points out that it's only for ICS and aborts the installation. So I fixed the permission manually.
Now I'm going to check the rest and see what happens.
Fixed permission, flashed update-signed.zip, wiped davlink and cache, rebooted and... well, after HTC logo the screen turned off and only the hardkeys were illuminated
I'm going to flash the rom again and start from the beginning for the third time.
Click to expand...
Click to collapse
I saw that you are going to install Paranoid anyway, I have flashed CM10 recently so I have to redo my Supercharger and I will explain it in detail for you.
I will edit this post but give you a overview first.
I recommend to flash Gapps first and then enable a2sd.
Try installing Supercharger without the use of Starter Kit, Busybox, SQlite and SU binaries (v3.2) are preinstalled (if you want to check for update anyway check it in SuperUser app)
StarterKit is designed to give everyone the TESTED busybox version, to avoid problems, but try it without the installation of StarterKit, just if it doesn't work because of busybox get the one of StarterKit (I will try it with preinstalled version, not the one of StarterKit)
So here are my steps, I'll try:
1. patch services.jar with offline mode, then put the output service.jar with ES File Explorer in /system/framework
2. With terminal emulator I will set the permissions and the owner
3. I will launch the Superuser script.
You can try this while I am using this method, too, but in any case I will report if it works or not
Edit: I decided to make a video, for this I will use StarterKit too, to show everything.
chico1620 said:
Hey mate can you make a youtube video showing the steps. I understand better with visuals, and thanks for sharing.
Sent from my HTC Desire using xda app-developers app
Click to expand...
Click to collapse
I'll have to see, I have only a camera of the year 2005 or a old samsung phone of the year 2008/2009
I don't know if the quality would be good enough + I would do it only for 4.0+ ROM
Androidmarketuser said:
I'll have to see, I have only a camera of the year 2005 or a old samsung phone of the year 2008/2009
I don't know if the quality would be good enough + I would do it only for 4.0+ ROM
Click to expand...
Click to collapse
Does not matter my problem is the terminal coding i dont want to mess it up and change something crucial.
Sent from my HTC Desire using xda app-developers app
chico1620 said:
Does not matter my problem is the terminal coding i dont want to mess it up and change something crucial.
Sent from my HTC Desire using xda app-developers app
Click to expand...
Click to collapse
I'm currently making a video but I don't know if I can upload it today, but tomorrow you'll have it in any case
Quality is good I noticed.
Androidmarketuser said:
I'm currently making a video but I don't know if I can upload it today, but tomorrow you'll have it in any case
Quality is good I noticed.
Click to expand...
Click to collapse
Omg ty mate, i will be looking forward to it. Im also trying to follow your guide and see how things go, jopefully i succeed
Sent from my HTC Desire using xda app-developers app
Androidmarketuser said:
I saw that you are going to install Paranoid anyway, I have flashed CM10 recently so I have to redo my Supercharger and I will explain it in detail for you.
I will edit this post but give you a overview first.
I recommend to flash Gapps first and then enable a2sd.
Try installing Supercharger without the use of Starter Kit, Busybox, SQlite and SU binaries (v3.2) are preinstalled (if you want to check for update anyway check it in SuperUser app)
StarterKit is designed to give everyone the TESTED busybox version, to avoid problems, but try it without the installation of StarterKit, just if it doesn't work because of busybox get the one of StarterKit (I will try it with preinstalled version, not the one of StarterKit)
So here are my steps, I'll try:
1. patch services.jar with offline mode, then put the output service.jar with ES File Explorer in /system/framework
2. With terminal emulator I will set the permissions and the owner
3. I will launch the Superuser script.
You can try this while I am using this method, too, but in any case I will report if it works or not
Click to expand...
Click to collapse
Thank you, you are very patient and nice!
Yes I'm indeed trying Paranoid, because it solves the big problem I had with Elk's CM10 (wifi not working with wifi networks with PEAP), although it is slower and I intend to revert back as soon as the problem is fixed.
I will try your method, hoping that the hateful fragmentation fault problem doesn't occur anymore. :fingers-crossed:
aledex said:
Thank you, you are very patient and nice!
Yes I'm indeed trying Paranoid, because it solves the big problem I had with Elk's CM10 (wifi not working with wifi networks with PEAP), although it is slower and I intend to revert back as soon as the problem is fixed.
I will try your method, hoping that the hateful fragmentation fault problem doesn't occur anymore. :fingers-crossed:
Click to expand...
Click to collapse
Thanks for you thanks
I don't know if it is rally the segmentation (or whatever it's called) because it only occurs in ICS, if you want to install the su binary of the StarterKit it says NO because you don't need this (I think so)
I will upload a video tomorrow and I hope it solves your problem, for me everything's working fine
Does reinstalling the rom gets rid of the script? Because I'm currently using mildwild 5.0 and when I installed the supercharger script the rom got slightly slower, so I was wondering if reinstalling the rom gets rid of the script. Maybe I picked the wrong choices when installing the script I'm gonna wait for you to make a video so I can correctly do it.
Sent from my HTC Desire using xda app-developers app
chico1620 said:
Does reinstalling the rom gets rid of the script? Because I'm currently using mildwild 5.0 and when I installed the supercharger script the rom got slightly slower, so I was wondering if reinstalling the rom gets rid of the script. Maybe I picked the wrong choices when installing the script I'm gonna wait for you to make a video so I can correctly do it.
Sent from my HTC Desire using xda app-developers app
Click to expand...
Click to collapse
Reinstalling the rom deletes supercharger, because system is wiped (i think so)
The Video will show how you install the script, there aren't man decisions which you can choose incorrectly.
The speed is especially affeced by multitasking mod (keeps apps in memory, a bit less RAM for games) and freemem options which you choose in supercharger script, I recommend Option 6 for balanced settings.
AS I said the video only shows the basic things (and only for 4.0+)...
Edit: Video wont have many anotations, will be under time pressure
Sent from my HTC Desire using xda app-developers app
So.
As i was slowly preparing DSC v2.0 i met a hard decision: what root tool to include
Both Superuser and SuperSU are nice, but quite heavy
I decided to take my own way - rewrite su executable itself to suit my vision:
I've aknowledged that i have not modified my root access list for half a year. I don't need and don't want a separate Java process to control root access. I want a simple way to allow root access for application (via whitelist), but block unwanted (i.e. all not in list). Still, it should allow end-user to install either SuperSU or Superuser.
In short - ideal su solution for myself that should also work good for depersonalized custom ROM (with predefined access list), leaving it to end-user to decide which app he will install for superuser access.
And i didn't find a ready solution, so decided to write my own.
Here it is (attached):
SimpleSU
Simplest and lightest superuser solution (with access control)
How it's done:
Same as usual SU for Linux with control access list read from /system/etc/dsc.su_list
dsc.su_list structure is very simple:
One line per android app (case sensitive), windows and unix line breaks should be supported fine.
Current proposed list for DSC 2.0 (and an example):
dsc.SimpleSU.acl
dsc.settings
dsc.uv
dsc.levels
dsc.mugen
jackpal.androidterm
ru.org.amip.ClockSync
eu.chainfire.supersu
eu.chainfire.supersu.pro
com.ryosoftware.adbw
com.googlecode.droidwall.free
com.noshufou.android.su
de.schaeuffelhut.android.openvpn
de.schaeuffelhut.android.openvpn.installer
com.elsdoerfer.android.autostarts
com.speedsoftware.rootexplorer
com.geeksoft.screenshot
com.rerware.android.MyBackupPro
com.ghostsq.commander
ws.plattner.cifsmanager
mobi.pruss.superdim
com.force.timezonefixer
com.bigtincan.android.adfree
Caller process tree is walked till init, if match is found, access is granted.
How to install?
Via adb shell:
Code:
adb push su /system/xbin/
adb shell chmod 6755 /system/xbin/su
adb push dsc.su_list /system/etc
adb shell chown root.root /system/etc/dsc.su_list
adb shell chmod 644 /system/etc/dsc.su_list
Note that you have to manually add entries to white list (/system/etc/dsc.su_list) to grant root access in form of app full Java class name. For example, it's com.keramidas.TitaniumBackup for Titanium Backup.
As pointed by dr911, works in multiuser environment (being a linux binary).
Currenly SimpleSU supports two command formats:
Usual: su -c 'make me a sandwich'. Note that only "-c" works now. Seems to be enough though. Command simply passed to the shell.
Legacy (as seen in Google/Android su source): su username make me a sandwich. Shell is not executed in this case, so no environment variables right now in this format.
Have fun,
Sergei.
Changelog:
02.04.2013: v0.7. ":service" suffix granted root access for already granted app, more logging on reject. (0.6 had only more logging)
27.11.2012: GUI updated - forgot about remounting /system in rw mode. Attached to this post.
21.11.2012: GUI done. http://forum.xda-developers.com/showpost.php?p=34439975&postcount=41
14.11.2012: v0.5. LD_LIBRARY_PATH fixup (taken from ChainsDD), pointed by Rupert Rawnsley. Also some legacy format command-line handling changed. Also, insecure version added (no checks made, asked=granted).
11.11.2012: v0.4. Code cleanup, no longer beta, revised and fixed code with potential string overflows.
09.11.2012: v0.3b. Code changed to allow legacy format command execution.
09.11.2012: v0.2b. Fixed call with multiply parameters. OpenVPN installer works. Dynamic linking, so very small binary. Logging to system log.
07.11.2012: Fixed segmentation fault on reject, added version and build date, removed debug info.
A request:
If somebody owns Pro/Elite/other commercial Superuser or SuperSU - would you provide it's full Java class name?
For example, it's
eu.chainfire.supersu
com.noshufou.android.su
for free versions.
eu.chainfire.supersu.pro
Sent from my Amazon Kindle Fire using Tapatalk 2
Can I avoid these little delays (the appearing popup of SuperSU or Superuser) with this alternative?
And if I have Superuser preinstalled can I delete it and are there other files which belongs to it and can be deleted?
Thank you for sharing your work
com.noshufou.android.su.elite for Superuser Elite
Hi
Have you noticed any improvement in terms of speed etc? Is superuser really that heavy? How much RAM can i get by using this and ditching the superuser app? We can use this in our Galaxy 3 forum !
Get the list of all android activities from here
http://activities.droidicon.com/
Androidmarketuser said:
Can I avoid these little delays (the appearing popup of SuperSU or Superuser) with this alternative?
And if I have Superuser preinstalled can I delete it and are there other files which belongs to it and can be deleted?
Thank you for sharing your work
Click to expand...
Click to collapse
Delete system/xbin/su and uninstall your superuser app from the system.
Oh. Looks SimpleSU got in news
Androidmarketuser said:
Can I avoid these little delays (the appearing popup of SuperSU or Superuser) with this alternative?
And if I have Superuser preinstalled can I delete it and are there other files which belongs to it and can be deleted?
Thank you for sharing your work
Click to expand...
Click to collapse
You won't experience any delays - but in cost of manually editing the list. And no popups, it's simply a linux binary. After replacing su binary you may uninstall Java part.
Shree_Jamdar said:
Have you noticed any improvement in terms of speed etc? Is superuser really that heavy? How much RAM can i get by using this and ditching the superuser app? We can use this in our Galaxy 3 forum !
Click to expand...
Click to collapse
I did experience lags when using Superuser and SuperSU. I don't think modern device would benefit from SimpleSU. I expect to free 15-20MB. Good for Streak with 512MB.
I may eventually write a list editor, but most probably won't.
Again, this tool would do as preinstalled SU solution in Custom ROM (though i can't test >2.3 compatibility):
Grant predefined (and included in ROM) apps the superuser rights.
Allow end-user to choose and install he's preffered SU solution right from Play Store.
--
Have fun,
Sergei
_n0p_ said:
You won't experience any delays - but in cost of manually editing the list. And no popups, it's simply a linux binary. After replacing su binary you may uninstall Java part.
I did experience lags when using Superuser and SuperSU. I don't think modern device would benefit from SimpleSU. I expect to free 15-20MB. Good for Streak with 512MB.
I may eventually write a list editor, but most probably won't.
Again, this tool would do as preinstalled SU solution in Custom ROM (though i can't test >2.3 compatibility):
Grant predefined (and included in ROM) apps the superuser rights.
Allow end-user to choose and install he's preffered SU solution right from Play Store.
--
Have fun,
Sergei
Click to expand...
Click to collapse
Exactly what I searched, thanks :good:
I will test it on my old Desire with Android 4.1, I can tell you whether it's compatible or not.
nice tool...very lite. i m using this in extreme barebone roms for my galaxy mini. really nice, but the problem is only some apps r being granted permissions, some denied.
i hope u increase the list of activities. then this is a hit for me
good luck..
Android_United said:
nice tool...very lite. i m using this in extreme barebone roms for my galaxy mini. really nice, but the problem is only some apps r being granted permissions, some denied.
i hope u increase the list of activities. then this is a hit for me
good luck..
Click to expand...
Click to collapse
Can you provide an example of app you have added to the access list, but it didn't work?
i looked in the op and still dont understand how to install?? flash the simple SU zip in recovery.. then what???
evo401 said:
i looked in the op and still dont understand how to install?? flash the simple SU zip in recovery.. then what???
Click to expand...
Click to collapse
if you couldnt read/understand the OP, then your probably better off sticking with SuperSU or SuperUser...
Heres my non-developer understanding (potentially flawed):
Its a binary, with manual entry's (IE text editing) of pre-approved apps, it doesnt have a frontend/gui like SuperSU or SuperUser which allow you to graphically chose what to allow and what to deny...
OP: I like it so far, as for your thoughts on a graphical editor, I for one would love to see one, and before I get jumped for saying then whats the difference between the other options, an editor would be short and sweet, open, edit list, close, ram once again free (since that is the concern), instead of having it stay resident in RAM...
On that note, if I may, there are tools like Rays Toolbox and Android Tuner (formerly system tuner), that I would like to put in a feature request for them to add an editor in the app (Android Tuner already has a few editor's, adding a SimpleSU editor would just add to the overall completeness of the toolkit) to edit the list for SimpleSU, with your permission of course!
Thanks again!
Latest version working on Galaxy fit !!! It really imporves performance on low ram(We got 256mb) devices maybe OP might consider sharing it by moving thread to a more general location on xda rather than on a device forum my thoughts.
Dark Passenger said:
Latest version working on Galaxy fit !!! It really imporves performance on low ram(We got 256mb) devices maybe OP might consider sharing it by moving thread to a more general location on xda rather than on a device forum my thoughts.
Click to expand...
Click to collapse
Yes, exactly.. it works on galaxy y duos and galaxy yseries.. its better to move it to android app development section may be? as it will get more support there i feel.. Please do consider op.. And thanks for this cool app.. Its awesome. And i dont think it needs an editor, as we can have editors from many apps .. i have around 4-5 apps which has editors.. surely users who use this app will be bit advanced users..
and i bet all of them will have file editors.. and all file explorer apps comes with editors nowadays.. well , just my thoughts.. but if you can keep the file browser to bare minimum and keep size of apk less.. then i would surely like to see it too
i am hoping to use this from now on.. so i will give review for new updates.. have you pushed it to play store? i think you should do that.. many will like this idea!
Thanks again..
As far as i understood we can edit it to add new apk names to give permission.. Because Android_united kinda confused me.. So, asked this again.. i did use it and it did worked.. its just may be he didnt see that?
Works like a charm! The only problem I had is that I was doing this through Terminal Emulator, and for some reason, when i did all this, superuser perrmisions were not granted for Terminal Emulator. After a little digging i found that i have to add this line
Code:
jackpal.androidterm2
and leave the one that's there by default
Code:
jackpal.androidterm
to the dsc.su_list
Now it works, i have SU for Terminal Emulator, Adfree, and i added SetDNS (Impossible to use Google play on CM7.2 without it )
I like the idea of this but be extra careful to only whitelist activities you really use.
I could imagine a malware somehow managing to enter your system and masquerading as one of the prepopulated entries in dsc.su_list, though of course no such vulnerability exists so far.
Thank you for feedback.
--
I cannot publish it on Play Store - it's not an Android app. To publish it, i need to write SimpleSU Installer, or something like that (see below).
--
Regarding editor - it would be nice if someone else would write it I really don't expect to have enough free time required.
--
A 0.4 version i consider as stable (revised potentially bad code with possible string overflows) attached to first post.
--
Malware that could act as Java class - i thought of several scenarios, but any requres root access beforehand. And if you install an app - it's your responsibily to be careful.
--
Have fun,
Sergei
_n0p_ said:
Can you provide an example of app you have added to the access list, but it didn't work?
Click to expand...
Click to collapse
titanium backup, es-file explorer. i tested wit only these 2. as these 2 weren't gaining root access, so i stopped using this. if u want me to test wit more apps, i can help u out.
will be using this surely once it receives more updates :good:
:good: gud luck..