Modem + NON-HILOS
extract zip
Flash once with odin (no reboot)
Flash again with odin, reboot and
Enjoy
TELCEL NE2 https://mega.co.nz/#!qIxWhChD!VnNJw5uSsbjpxhSZX0esvRglo4QtcrkWApRnInyiPBc
CLARO NE3 https://mega.co.nz/#!rJwjgDaQ!L6rQf5S-1Zf2LLKO5nNUPdKOMAs1KRjlRsMadMcEwIw
djdedonrg said:
Modem + NON-HILOS
extract zip
flash with odin 2 times
Enjoy
https://mega.co.nz/#!qE5nzbBI!aogwLwt1B7Up0MgicUL4IVN7Fb6LM32C9_f-3ClAvjI
Click to expand...
Click to collapse
When did that come out?
I thought NC1 was the latest ?
Mine is NE1. Same question. When did it come and which carrier was it from? Thanks.
Sent from my GT-I9505G using Tapatalk
Extracted from latest firmware CLARO (Puerto Rico) June
What does non-hilOS mean? Do I have to flash both or just modem? Thanks.
Sent from my GT-I9505G using Tapatalk
Wondering if flashing this would fix my 5GHz wifi having terrible connection. Assuming the modem includes WIFI stuff, I have no idea.
ma678 said:
What does non-hilOS mean? Do I have to flash both or just modem? Thanks.
Sent from my GT-I9505G using Tapatalk
Click to expand...
Click to collapse
Flash modem only....
Is it safe to flash this modem on my Canadian i337m? Thanks.
Sent from my GT-I9505G using Tapatalk
I tried to flash it twice, but all failed.
Sent from my GT-I9505G using Tapatalk
If you are sure this flashear modem i337m, flashear without auto reboot, re-flashear with auto reboot
I tried two different laptops, all failed.
Sent from my SGH-I337M using Tapatalk
ma678 said:
I tried two different laptops, all failed.
Sent from my SGH-I337M using Tapatalk
Click to expand...
Click to collapse
Flash once with odin unchecking auto reboot,
mark the error,( no reboot )
now unplug USB cable and then reconnect
Flash again with odin, auto check reboot now
Repeat steps one more time
enjoy!
djdedonrg said:
Flash once with odin unchecking auto reboot,
mark the error,( no reboot )
now unplug USB cable and then reconnect
Flash again with odin, auto check reboot now
Repeat steps one more time
enjoy!
Click to expand...
Click to collapse
<ID:0/012> Added!!
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> SingleDownload.
<ID:0/012> modem.bin
<ID:0/012> NAND Write Start!!
<ID:0/012> Transmission Complete..
<ID:0/012> Now Writing.. Please wait about 2 minutes
<ID:0/012> FAIL! (Auth)
<ID:0/012>
<ID:0/012> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/012> Removed!!
<ID:0/012> Added!!
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> SingleDownload.
<ID:0/012> modem.bin
<ID:0/012> NAND Write Start!!
<ID:0/012> Transmission Complete..
<ID:0/012> Now Writing.. Please wait about 2 minutes
<ID:0/012> FAIL! (Auth)
<ID:0/012>
<ID:0/012> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/012> Removed!!
<ID:0/012> Added!!
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> SingleDownload.
<ID:0/012> modem.bin
<ID:0/012> NAND Write Start!!
<ID:0/012> Transmission Complete..
<ID:0/012> Now Writing.. Please wait about 2 minutes
<ID:0/012> FAIL! (Auth)
<ID:0/012>
<ID:0/012> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/012> Removed!!
<ID:0/012> Added!!
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> SingleDownload.
<ID:0/012> modem.bin
<ID:0/012> NAND Write Start!!
<ID:0/012> Transmission Complete..
<ID:0/012> Now Writing.. Please wait about 2 minutes
<ID:0/012> FAIL! (Auth)
<ID:0/012>
<ID:0/012> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/012> Removed!!
<ID:0/012> Added!!
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> SingleDownload.
<ID:0/012> modem.bin
<ID:0/012> NAND Write Start!!
<ID:0/012> Transmission Complete..
<ID:0/012> Now Writing.. Please wait about 2 minutes
<ID:0/012> FAIL! (Auth)
<ID:0/012>
<ID:0/012> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
Tried few more times still didn't work.
ma678 said:
<ID:0/012> Added!!
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> SingleDownload.
<ID:0/012> modem.bin
<ID:0/012> NAND Write Start!!
<ID:0/012> Transmission Complete..
<ID:0/012> Now Writing.. Please wait about 2 minutes
<ID:0/012> FAIL! (Auth)
<ID:0/012>
<ID:0/012> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/012> Removed!!
<ID:0/012> Added!!
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> SingleDownload.
<ID:0/012> modem.bin
<ID:0/012> NAND Write Start!!
<ID:0/012> Transmission Complete..
<ID:0/012> Now Writing.. Please wait about 2 minutes
<ID:0/012> FAIL! (Auth)
<ID:0/012>
<ID:0/012> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/012> Removed!!
<ID:0/012> Added!!
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> SingleDownload.
<ID:0/012> modem.bin
<ID:0/012> NAND Write Start!!
<ID:0/012> Transmission Complete..
<ID:0/012> Now Writing.. Please wait about 2 minutes
<ID:0/012> FAIL! (Auth)
<ID:0/012>
<ID:0/012> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/012> Removed!!
<ID:0/012> Added!!
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> SingleDownload.
<ID:0/012> modem.bin
<ID:0/012> NAND Write Start!!
<ID:0/012> Transmission Complete..
<ID:0/012> Now Writing.. Please wait about 2 minutes
<ID:0/012> FAIL! (Auth)
<ID:0/012>
<ID:0/012> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/012> Removed!!
<ID:0/012> Added!!
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> SingleDownload.
<ID:0/012> modem.bin
<ID:0/012> NAND Write Start!!
<ID:0/012> Transmission Complete..
<ID:0/012> Now Writing.. Please wait about 2 minutes
<ID:0/012> FAIL! (Auth)
<ID:0/012>
<ID:0/012> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
Tried few more times still didn't work.
Click to expand...
Click to collapse
Try to Odin v3.07
I just updated the first post, something was wrong with the modem NE3, I went back up and now everything is perfect, all an apology.
also went up the new modem TELCEL I337MUMUFNE2 NE2
djdedonrg said:
I just updated the first post, something was wrong with the modem NE3, I went back up and now everything is perfect, all an apology.
also went up the new modem TELCEL I337MUMUFNE2 NE2
Click to expand...
Click to collapse
So which modem are you using, NE2 or NE3? What was your problem? Thanks.
Sent from my GT-I9505G using Tapatalk
The problem was uploading the file was corrupted, now I'm using the NE2 telcel.
The modem is the newest CLARO NE3
The files and work perfectly and again apologize to everyone.
First picture with modem TELCEL
Second photo with modem CLARO NE3
New NE3 works for me after the first flash. I haven't seen significant change yet.
Thanks.
Sent from my GT-I9505G using Tapatalk
I had to use the older Odin 3.07 to get it to "stick".
Instructions I followed
1. Unplug phone from computer or any charger, etc.
2. Remove battery from phone, wait 10 seconds, re-insert battery.
3. Power up phone holding the volume down and home button until warning screen, hit up volume to continue.
4. Plug USB cable from computer into phone, wait 30 seconds.
5. Launch Odin 3.07, put a checkmark beside phone, pick the modem.bin file extracted from NE3 rar file. UNCHECK auto reboot, then flash.
6. When flashing is complete close Odin.
7. Unplug USB cable from phone.
8. Wait 10 seconds, plug phone back in.
9. Wait 30 seconds, open Odin 3.07, put a checkmark beside phone, pick same modem.bin file, this time leave auto reboot checked, flash away.
10. As soon as screen on phone goes blank unplug USB cable from computer and let phone boot under its own power.
I flashed it probably 10 times and it never worked until I followed those exact steps. Not sure if it was removing the battery before starting that is the trick or not.
Check out the release date on the kernel!!! Bleeding edge baby
-Jamie M.
Jamie,
How about signal strength and battery drain on the new NE3 and the latest GPE ROM? I found my battery drains quicker than previous one.
toysareforboys said:
I had to use the older Odin 3.07 to get it to "stick".
Instructions I followed
1. Unplug phone from computer or any charger, etc.
2. Remove battery from phone, wait 10 seconds, re-insert battery.
3. Power up phone holding the volume down and home button until warning screen, hit up volume to continue.
4. Plug USB cable from computer into phone, wait 30 seconds.
5. Launch Odin 3.07, put a checkmark beside phone, pick the modem.bin file extracted from NE3 rar file. UNCHECK auto reboot, then flash.
6. When flashing is complete close Odin.
7. Unplug USB cable from phone.
8. Wait 10 seconds, plug phone back in.
9. Wait 30 seconds, open Odin 3.07, put a checkmark beside phone, pick same modem.bin file, this time leave auto reboot checked, flash away.
10. As soon as screen on phone goes blank unplug USB cable from computer and let phone boot under its own power.
I flashed it probably 10 times and it never worked until I followed those exact steps. Not sure if it was removing the battery before starting that is the trick or not.
Check out the release date on the kernel!!! Bleeding edge baby
-Jamie M.
Click to expand...
Click to collapse
Related
Hello. Sorry for my enlgish.
Theres a soft-bricked SM-P900, I can normally open download mode. (But on normal system loading it asking for Kies)
(Samsung Galaxy Note Pro 12.2 WiFi SM-P900)
No ROM installed now. I just can't install it.
Here's the Odin log:
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
It's always stucks on "system.img" in ANY .tar I try to flash.
Yesterday, it could power on. But now it's not powering on at all. I hope this is because of battery charge.
===UPD: Yes, it was because of battery charge. Now it's powered on
===UPD2: Now it's powered off again and I can't power it on, what the hell?...
What should I do, guys? Help, please!
Thread closed / Duplicate
odin 3.10 says this when i try to install firmware on my bricked s6 edge.
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can someone please help me.
Mate ur failed is at bootloader means u Trying to flash old bootloader on newer one then knox wont let u install it success so download the latest fw from sammobile firmweare then flash it again ok
Good luck,,
Hi Dear;
i have a problem with s6. I rooted it 1 year ago. Than i will try to remove root. When i try to unroot my phone will crush.Than i cant open it. I found the stock rom in internet but i can't flash it. I see this error o odin. How can i fix it . Please help me guys. Save me from this trouble.
I add 4 rom to odin BL-AP-CP-CSC all stock rom. Than it's error.
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Is it G920F?
Hey,
I keep having issues with my S8+ that has never been rooted. I flashed it trying to fix an issue with my WiFi forgetting saved networks. If I turned off WiFi or rebooted my phone it forget all saved networks.
I used Samfirm and Odin 3.12.7 to flash it to the latest firmware AQJ4 and then did an OTA update that popped up. I'm still having the issue but keep getting a notification about "Unauthorized modifications, reboot".
Now, I can't even flash the phone anymore... I keep getting a Fail! (Auth) error when trying to flash BL, AP, or CSC... CP seems to work fine.
I've tried everythign I can find online but nothing helps... When in download mode I see:
FRP Lock is off
Warranty Voidis 0x0
System Status is Official
The one thing I've noticed is that my device shows Baseband version AQJ4 but my Build number is AQK3... Is that normal?
Any ideas?
Code:
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1207)..
<ID:0/004> File analysis..
<ID:0/004> skip file list for home binary
<ID:0/004> apdp.mbn
<ID:0/004> msadp.mbn
<ID:0/004> persist.img.ext4
<ID:0/004> userdata.img.ext4
<ID:0/004> Home Binary Download
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> abl.elf
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Ok so ive been trying to flash twrp so i can flash cyanogen mod on my g930u. Its not rooted and ive used many diffirent cables, laptops, versions of odin to no avail. I downloaded the .tar version of the latest version of twrp for it. usb debugging and oem unlocking are on and frp lock is off. This is the error message i get when trying to flash twrp. Auto reboot is also off. Also tried diffirent pc usb ports. The phone is also in perfect condition and works fine. please help
<ID:0/012> Added!!
<ID:0/012> Removed!!
<ID:0/012> Added!!
<ID:0/012> Odin engine v(ID:3.1301)..
<ID:0/012> File analysis..
<ID:0/012> Total Binary size: 43 M
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> NAND Write Start!!
<ID:0/012> SingleDownload.
<ID:0/012> recovery.img
<ID:0/012> RQT_CLOSE !!
<ID:0/012>
<ID:0/012> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Please help
Varied Gamer said:
Ok so ive been trying to flash twrp so i can flash cyanogen mod on my g930u. Its not rooted and ive used many diffirent cables, laptops, versions of odin to no avail. I downloaded the .tar version of the latest version of twrp for it. usb debugging and oem unlocking are on and frp lock is off. This is the error message i get when trying to flash twrp. Auto reboot is also off. Also tried diffirent pc usb ports. The phone is also in perfect condition and works fine. please help
<ID:0/012> Added!!
<ID:0/012> Removed!!
<ID:0/012> Added!!
<ID:0/012> Odin engine v(ID:3.1301)..
<ID:0/012> File analysis..
<ID:0/012> Total Binary size: 43 M
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> NAND Write Start!!
<ID:0/012> SingleDownload.
<ID:0/012> recovery.img
<ID:0/012> RQT_CLOSE !!
<ID:0/012>
<ID:0/012> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Please help
Click to expand...
Click to collapse
You need to root it first, as in access to root directory. You can't do nothing until you've done that.
cooltt said:
You need to root it first, as in access to root directory. You can't do nothing until you've done that.
Click to expand...
Click to collapse
One of my friends has the same model unrooted and he was able to get it to flash first try and said I don't need root.
Varied Gamer said:
One of my friends has the same model unrooted and he was able to get it to flash first try and said I don't need root.
Click to expand...
Click to collapse
Well get your friend to do it, what do we know.