Don't mix this guide with some other as i will not help in that case.
First of all, use read back to get rom dump (backup) as there is no stock rom available on net.
Go here and follow the guide.
Procedure:
1. Download and install drivers Driver_Auto_Installer_v1.1236.00.7z.
If not working try these too PDAnet_4150.rar.
Problem in installation?? Go here
2. Download and copy/move SuperUser to your memory card.
3. Download any kitkat recovery from here and place it in pc.
4. Open SP Flash tools and load this MT6582_Android_scatter.txt in it. (alternative download link of sp flash tools)
5. Click on 'recovery' in sp flash tools and select the downloaded Recovery .
6. Click Download in sp flash tools, remove the battery from phone and connect it to pc.
A green circle/download ok will confirm flashing.
7. Insert battery and press volume up+down+power on, then press volume up to select recovery.
Note: in ctr recovery you can swipe right to go forward and swipe back to go backward, use it to navigate, save volume buttons.
8. Tap on install from sd card and swipe right on screen to go forward, select "superuser.zip" and say yes to flash.
9. Reboot, Done.
In case any one wants working MTK droid tools, here or here
Please subscribe, rate and like this thread.
Sudeep Duhoon said:
...
Click to expand...
Click to collapse
i hope that this would work on my device too hehe
1st btw
hi Sudeep Duhoon can u plz upload the rom of unite 2
asif09ansari said:
hi Sudeep Duhoon can u plz upload the rom of unite 2
Click to expand...
Click to collapse
U can get it using read back.
Sent from my Micromax A106 using Tapatalk
Sudeep Duhoon said:
U can get it using read back.
Sent from my Micromax A106 using Tapatalk
Click to expand...
Click to collapse
i dont have the handset i want to port it to canvas A114
Rom size is 700mb i can't upload that much.
Sent from my Micromax A106 using Tapatalk
TWRP 2.5
hey i ported TWRP 2.5 , try this : http://d-h.st/LUZ
Shikhar A said:
hey i ported TWRP 2.5 , try this : http://d-h.st/LUZ
Click to expand...
Click to collapse
It's flipped.
Sent from my MyPhone Agua Rio Lite using Tapatalk
Sudeep Duhoon said:
It's flipped.
Sent from my MyPhone Agua Rio Lite using Tapatalk
Click to expand...
Click to collapse
u mean totally opposite? .... 180 * turned?
---------- Post added at 04:57 PM ---------- Previous post was at 04:55 PM ----------
Sudeep Duhoon said:
It's flipped.
Sent from my MyPhone Agua Rio Lite using Tapatalk
Click to expand...
Click to collapse
Can i get stock recovery.img ??
Well done .
But can you please try porting clockworkmod recovery .
Hello guys is anyone working to fix the usb otg
---------- Post added at 05:56 PM ---------- Previous post was at 05:52 PM ----------
Also requesting mods to create a section for mmx unite 2 it will be very help full
thanks
Sudeep Duhoon said:
..
Click to expand...
Click to collapse
friend i have found another alleged rebrand of our unit: wiko bloom
Scatter file
Sudeep Duhoon said:
...
Click to expand...
Click to collapse
how are you? if you have the time can you please check the scatter file from this Stock rom of mmx unite 2 because he instructed to use a different version of scatter file, is this normal? its only a request if you have the time..thanks in advance
unite 2
custom rom for micromax unite 2 ?
Can someone provide the Stock (Kitkat) ROM
Sudeep Duhoon said:
Don't mix this guide with some other as i will not help in that case.
First of all, use read back to get rom dump as there is no stock rom available on net.
Use the scatter from this thread and latest flash tools (the one i used is in downloads below)
Guide for Read Back:
Guide on how to read back or consider google, don't ask me about this.
Procedure:
1. Download and install MTK VCOM drivers.
2. Download and copy/move SuperSU v1.99r3.zip to your memory card.
3. Download this CTR v2.2 Recovery and place it in pc.
4. Open SP Flash tools and load this MT6582_Android_scatter.txt in it. (alternative download link of sp flash tools)
5. Click on 'recovery' in sp flash tools and select the downloaded CTR v2.2 Recovery .
6. Click Download in sp flash tools, remove the battery from phone and connect it.
A green circle will confirm flashing.
7. Insert battery and press volume up+down+power on, then press volume up to select recovery.
Note: in ctr recovery you can swipe right to go forward and swipe back to go backward, use it to navigate, save volume buttons.
8. Tap on install from sd card and swipe right on screen to go forward, select SuperSU.zip and say yes to flash.
9. Reboot, Done.
In case any one wants working MTK droid tools, here or here
Please subscribe, rate and like this thread.
Any problem, ask in fb group or pm me on facebook.
Click to expand...
Click to collapse
Can you try to port cwm on our device micromax a106 unite 2.....the methods shown on some websites are not working for me
Sudeep Duhoon said:
Don't mix this guide with some other as i will not help in that case.
First of all, use read back to get rom dump as there is no stock rom available on net.
Use the scatter from this thread and latest flash tools (the one i used is in downloads below)
Guide for Read Back:
Guide on how to read back or consider google, don't ask me about this.
Procedure:
1. Download and install MTK VCOM drivers.
2. Download and copy/move SuperSU v1.99r3.zip to your memory card.
3. Download this CTR v2.2 Recovery and place it in pc.
4. Open SP Flash tools and load this MT6582_Android_scatter.txt in it. (alternative download link of sp flash tools)
5. Click on 'recovery' in sp flash tools and select the downloaded CTR v2.2 Recovery .
6. Click Download in sp flash tools, remove the battery from phone and connect it.
A green circle will confirm flashing.
7. Insert battery and press volume up+down+power on, then press volume up to select recovery.
Note: in ctr recovery you can swipe right to go forward and swipe back to go backward, use it to navigate, save volume buttons.
8. Tap on install from sd card and swipe right on screen to go forward, select SuperSU.zip and say yes to flash.
9. Reboot, Done.
In case any one wants working MTK droid tools, here or here
Please subscribe, rate and like this thread.
Any problem, ask in fb group or pm me on facebook.
Click to expand...
Click to collapse
Can you try to port cwm to micromax unite 2 a106 ??
I heard that bootloader is locked and we need to replace boot.img as well with unlocked bootloader.
I tried to flash boot.img and recovery.img but getting 8038 error in SP flash tool, I used v1344, do you have any idea about this error?
Though I would try with latest version of SP Flash Tool and post the result.
nice_guy75 said:
I heard that bootloader is locked and we need to replace boot.img as well with unlocked bootloader.
I tried to flash boot.img and recovery.img but getting 8038 error in SP flash tool, I used v1344, do you have any idea about this error?
Though I would try with latest version of SP Flash Tool and post the result.
Click to expand...
Click to collapse
I am too getting the same error 8038.... tried the latest version of SP Flash tool too but no results
shri.vaibhav said:
I am too getting the same error 8038.... tried the latest version of SP Flash tool too but no results
Click to expand...
Click to collapse
nice_guy75 said:
I heard that bootloader is locked and we need to replace boot.img as well with unlocked bootloader.
I tried to flash boot.img and recovery.img but getting 8038 error in SP flash tool, I used v1344, do you have any idea about this error?
Though I would try with latest version of SP Flash Tool and post the result.
Click to expand...
Click to collapse
Don't mix this guide with some other.
This is working 100% there is no need of any mtk droid unlocked or something boot.img.
I will not help if you had followed any other guide and asking help from me, as i don't know what you had done and what not.
If you had followed only this guide properly, you must had got ctr recovery + root access.
Follow any guide over the internet but never mix things up and ask all the devs for help.
Related
I've upgraded my canvas 2 tl official jellybean rom v3.
I tried to root it with the step used to root canvas 2 on ICS, but it didn't work.
So pleaase guys, show me method to root it on Micromax A110 JB.
Thanks
i had faced same problem
what i did was simple i used cwm recovery to install cwm flashable supersu zip
what you need is sp flash tools, latest jellybean update from micromax and cwm recovery flash file
to make it easy you just go through this tutorial posted on droideser for a116
link is here droidiser.com/2013/03/working-rooting-guide-for-micromax-a116.html
but insted you take everything for a110
if you find this difficult please pm me ill make write down method
welcome
milav said:
i had faced same problem
what i did was simple i used cwm recovery to install cwm flashable supersu zip
what you need is sp flash tools, latest jellybean update from micromax and cwm recovery flash file
to make it easy you just go through this tutorial posted on droideser for a116
link is here droidiser.com/2013/03/working-rooting-guide-for-micromax-a116.html
but insted you take everything for a110
if you find this difficult please pm me ill make write down method
welcome
Click to expand...
Click to collapse
It would be really great help if you write a clear method step by step, because I'm not expert at these things..I've clicked thanks button.. waiting for your method..
PS : I have Stock rom JellyBean 4.1.1 official and sp flash tool already,, just show me the method.
PPS: I wanna root only to increase CPU performance, without rooted its under 6k score of antutu benchmark. So I hope rooting will increase performance! ..
jafardhada said:
It would be really great help if you write a clear method step by step, because I'm not expert at these things..I've clicked thanks button.. waiting for your method..
PS : I have Stock rom JellyBean 4.1.1 official and sp flash tool already,, just show me the method.
PPS: I wanna root only to increase CPU performance, without rooted its under 6k score of antutu benchmark. So I hope rooting will increase performance! ..
Click to expand...
Click to collapse
please give me few hours to write down the procedure if you can wait thank you
Waiting for it
I am also waiting
Naughtie said:
Waiting for it
Click to expand...
Click to collapse
even i am waiting for your response to get resolution. please give it asap.
I m also in row please provide root ing tutorial asao for official jb MMX ROM
Sent from my Micromax A110 using xda app-developers app
rooting v3 jb rom of mmx110
I need help to root my MMX110 its flashed using Sp tool now i have V3 official ROM of Jellybean please help.................
Me also...
Sent from my Micromax A110 using xda app-developers app
---------- Post added at 01:01 PM ---------- Previous post was at 12:59 PM ----------
I try but installation abort with stock recovery
Sent from my Micromax A110 using xda app-developers app
---------- Post added at 01:02 PM ---------- Previous post was at 01:01 PM ----------
Superuser file empty nothing there I unzip
Sent from my Micromax A110 using xda app-developers app
Friendz install cwm recovery from sp flash tool and update super user binaries through cwm ......
that's too easy
Sent from my GT-I9300 using xda premium
Hit Thax if I help?
tell the method for mmx a110
I've upgraded my canvas 2 tl official jellybean rom v3.
I tried to root it with the step used to root canvas 2 on ICS, but it didn't work please guys, show me method to root it on Micromax A110 JB.
i also tried flash method also its also not working
vjdsivakumar said:
I've upgraded my canvas 2 tl official jellybean rom v3.
I tried to root it with the step used to root canvas 2 on ICS, but it didn't work please guys, show me method to root it on Micromax A110 JB.
i also tried flash method also its also not working
Click to expand...
Click to collapse
for all of those who are facing this problem, i am posting the link here follow the instructions given there,
1) http://d-h.st/zEb this is for the official mmx jb 1.11 rom
2) http://d-h.st/2Hn this is vcom drivers( download it and install it on your pc/laptop)
3) http://d-h.st/KyK this sp flash tool
4) http://linksredirect.com/?pub_id=562CL546&url=http://www.mediafire.com/download.php?aak733itivap95w THIS IS CWM RECOVERY FOR MMX A110( download this file on your computer and rename it " recovery.img" without quotes offcourse
5) http://linksredirect.com/?pub_id=562CL546&url=http://download.chainfire.eu/310/SuperSU-v1.04.zip THIS is SU binaries
now to begin, first install mmx a110 drivers(connect your phone via usb now swithch off phone without disconnecting, wait for a few min drivers will be installed,) second download file no 2 (vcom drivers) install them on your pc/laptop
now if you have already flashed jb 1.11, then open sp flash tool, click scatter loading choose MT6577_android_scatter_emmc.txt, it will load everything , now deselect every option except recovery( very imp make sure u deselect every option except recovery) click on recovery and choose the file you downloaded in option 4( and renamed recovery.img)
now turn off your phone, take out the battery, and keep it aside,
in sp flash tools click download button(not firmware upgrade) after that connect your phone(in powered off battery rmoved state) via usb, and you will have cwm recovery.
now after flashing, close flash tool, disconnect phone and power up,
now transfer the files you downloaded in step 5, to your sd card. now switch off the phone, hold vol down +vol up+ power button, get into recovery follow instructions there and get into cwm recovery, now choose option install from sd card and go to the files you transferred to your sd card from pc(one u downloaded in step 5) and just install them, NOW GIV URSELF A HIGH FIVE YOU HAVE ROOTED UR MMX
FOR FURTHER ASSISTANCE YOU CAN REFFER TO THESE THREADS,
1) http://forum.xda-developers.com/showthread.php?t=2167244
2) https://www.google.co.in/url?sa=t&r...n4GYAg&usg=AFQjCNEnye1swuWjZzXHN58fek2xrPmFQg
iTS NOT WORKING
mohit141785 said:
for all of those who are facing this problem, i am posting the link here follow the instructions given there,
1) http://d-h.st/zEb this is for the official mmx jb 1.11 rom
2) http://d-h.st/2Hn this is vcom drivers( download it and install it on your pc/laptop)
3) http://d-h.st/KyK this sp flash tool
4) http://linksredirect.com/?pub_id=562CL546&url=http://www.mediafire.com/download.php?aak733itivap95w THIS IS CWM RECOVERY FOR MMX A110( download this file on your computer and rename it " recovery.img" without quotes offcourse
5) http://linksredirect.com/?pub_id=562CL546&url=http://download.chainfire.eu/310/SuperSU-v1.04.zip THIS is SU binaries
now to begin, first install mmx a110 drivers(connect your phone via usb now swithch off phone without disconnecting, wait for a few min drivers will be installed,) second download file no 2 (vcom drivers) install them on your pc/laptop
now if you have already flashed jb 1.11, then open sp flash tool, click scatter loading choose MT6577_android_scatter_emmc.txt, it will load everything , now deselect every option except recovery( very imp make sure u deselect every option except recovery) click on recovery and choose the file you downloaded in option 4( and renamed recovery.img)
now turn off your phone, take out the battery, and keep it aside,
in sp flash tools click download button(not firmware upgrade) after that connect your phone(in powered off battery rmoved state) via usb, and you will have cwm recovery.
now after flashing, close flash tool, disconnect phone and power up,
now transfer the files you downloaded in step 5, to your sd card. now switch off the phone, hold vol down +vol up+ power button, get into recovery follow instructions there and get into cwm recovery, now choose option install from sd card and go to the files you transferred to your sd card from pc(one u downloaded in step 5) and just install them, NOW GIV URSELF A HIGH FIVE YOU HAVE ROOTED UR MMX
FOR FURTHER ASSISTANCE YOU CAN REFFER TO THESE THREADS,
1) http://forum.xda-developers.com/showthread.php?t=2167244
2) https://www.google.co.in/url?sa=t&r...n4GYAg&usg=AFQjCNEnye1swuWjZzXHN58fek2xrPmFQg
Click to expand...
Click to collapse
Hi i am facing the error as in the screenshot. Plz Helpp
Any other?
mohit141785 said:
for all of those who are facing this problem, i am posting the link here follow the instructions given there,
1) http://d-h.st/zEb this is for the official mmx jb 1.11 rom
2) http://d-h.st/2Hn this is vcom drivers( download it and install it on your pc/laptop)
3) http://d-h.st/KyK this sp flash tool
4) http://linksredirect.com/?pub_id=562CL546&url=http://www.mediafire.com/download.php?aak733itivap95w THIS IS CWM RECOVERY FOR MMX A110( download this file on your computer and rename it " recovery.img" without quotes offcourse
5) http://linksredirect.com/?pub_id=562CL546&url=http://download.chainfire.eu/310/SuperSU-v1.04.zip THIS is SU binaries
now to begin, first install mmx a110 drivers(connect your phone via usb now swithch off phone without disconnecting, wait for a few min drivers will be installed,) second download file no 2 (vcom drivers) install them on your pc/laptop
now if you have already flashed jb 1.11, then open sp flash tool, click scatter loading choose MT6577_android_scatter_emmc.txt, it will load everything , now deselect every option except recovery( very imp make sure u deselect every option except recovery) click on recovery and choose the file you downloaded in option 4( and renamed recovery.img)
now turn off your phone, take out the battery, and keep it aside,
in sp flash tools click download button(not firmware upgrade) after that connect your phone(in powered off battery rmoved state) via usb, and you will have cwm recovery.
now after flashing, close flash tool, disconnect phone and power up,
now transfer the files you downloaded in step 5, to your sd card. now switch off the phone, hold vol down +vol up+ power button, get into recovery follow instructions there and get into cwm recovery, now choose option install from sd card and go to the files you transferred to your sd card from pc(one u downloaded in step 5) and just install them, NOW GIV URSELF A HIGH FIVE YOU HAVE ROOTED UR MMX
FOR FURTHER ASSISTANCE YOU CAN REFFER TO THESE THREADS,
1) http://forum.xda-developers.com/showthread.php?t=2167244
2) https://www.google.co.in/url?sa=t&r...n4GYAg&usg=AFQjCNEnye1swuWjZzXHN58fek2xrPmFQg
Click to expand...
Click to collapse
If u dont mind... i there any other easier way to root it?
coz i had a rooted galaxy y duos and rooting it was too easy... this one is too complicated!
gvparab said:
Hi i am facing the error as in the screenshot. Plz Helpp
Click to expand...
Click to collapse
u messed up simply becoz u had logo selected along with recovery....chk d screenshot////
select recovery only.....then press download
it will work
---------- Post added at 02:08 PM ---------- Previous post was at 01:56 PM ----------
naman4797 said:
If u dont mind... i there any other easier way to root it?
coz i had a rooted galaxy y duos and rooting it was too easy... this one is too complicated!
Click to expand...
Click to collapse
flashing with d help of flash_tool is recommended and quite reliable but u can use d Bin4ry tool if u not accustomed.....
Is there any possibility of porting Rom of canvas HD A116 into canvas 2 A110.??
Is there any possibility of porting Rom of canvas HD A116 (4.2.1) in Canvas 2 A110...??
More specifically ... Porting official rom...!!
Heard that official jelly bean rom 4.2.1 is out for canvas hd A116... Please reply..
Click to expand...
Click to collapse
Not able to root
I tried to root many times but every time I am getting following message:
BROM ERROR: S_DA_SOC_CHECK_FAIL (3013)
Image is also attached
Flash tool problem
rkbs said:
Friendz install cwm recovery from sp flash tool and update super user binaries through cwm ......
that's too easy
Sent from my GT-I9300 using xda premium
Hit Thax if I help?
Click to expand...
Click to collapse
Hi,
I am trying to flash recovery using flash tools but getting the BROM ERROR.
SOC verification failed,
---------- Post added at 03:30 PM ---------- Previous post was at 03:17 PM ----------
ajayzitshi said:
I tried to root many times but every time I am getting following message:
BROM ERROR: S_DA_SOC_CHECK_FAIL (3013)
Image is also attached
Click to expand...
Click to collapse
Hi, @ajayzitshi
I followed every step carefully.
But still getting the same error. Did you get your phone rooted? What procedure you follow ?
Not able to Root
AnanyBoss said:
Hi,
I am trying to flash recovery using flash tools but getting the BROM ERROR.
SOC verification failed,
---------- Post added at 03:30 PM ---------- Previous post was at 03:17 PM ----------
Hi, @ajayzitshi
I followed every step carefully.
But still getting the same error. Did you get your phone rooted? What procedure you follow ?
Click to expand...
Click to collapse
Hi AnanyBoss,
Today again tried to root but again got the same BROM Error. I am following each & every step mentioned in this thread carefully bu still I am getting the same error. May be because I am having official JellyBean ROM from company it is not allowing to root.
ajayzitshi said:
Hi AnanyBoss,
Today again tried to root but again got the same BROM Error. I am following each & every step mentioned in this thread carefully bu still I am getting the same error. May be because I am having official JellyBean ROM from company it is not allowing to root.
Click to expand...
Click to collapse
flash suvi v9 custom ROM through sp tools.. it is sp tool flashable..... and prerooted
Hi Gurus,
I have always got all my answers on XDA-developers.com..... You people are simply the best.... Thanks for your support always.
I got my new Canvas 2 two months back. I have a problem that my GPS is not responding. I have googled a lot for the same and all reply that only method is to root my phone.
Also to note that I have already upgraded it to Jellybeans yesterday, but still GPS is not responding.
Now I think of rooting my phone but I have a clear idea that it will void my warranty. But I am very sure that XDA-developers will surely have some method out here to root the phone and again unroot the same so that I can gain my warranty back.
Please do help so that I can resolve my GPS issue I am really stucked.
Thanks in well advance.
Chin2 :silly:
Yes we are here to help you . Yeah you can root pr unroot your device anytime as you want . just install MTK tools and flash it with a custom rom . i will suggest you SUVI ROM V6 Hit thanks if i helped
Sent from my Micromax A110 using xda premium
maddyrokieasta said:
Yes we are here to help you . Yeah you can root pr unroot your device anytime as you want . just install MTK tools and flash it with a custom rom . i will suggest you SUVI ROM V6 Hit thanks if i helped
Sent from my Micromax A110 using xda premium
Click to expand...
Click to collapse
Hey Maddy,
Thanks for such a prompt reply.
I knew you people rock!!!
As I am a newbie to this, can you just guide with the steps to do the same.
It would be a great favour to me....
Thanks once again...
Chin2
ha ha sure ) please hit thanks on reply insted of saying it would be more GOod for me lol by the way these are the steps -
First you need to download your device drivers and install it to your computer .
2. download Suvi rom from thred section
3. extract it in a folder
4. switch off your device , remove the bettery
5. press + and - volume and Power keys together .
6. install apx driver
7 . A popup sound cm
8 . place files in MTK TOOLS which you have extacted it in a folder and start the installation .
switch off the device after success .
Done . Enjoy your rooted device .. HIT THANKS
Sent from my Micromax A110 using xda premium
maddyrokieasta said:
ha ha sure ) please hit thanks on reply insted of saying it would be more GOod for me lol by the way these are the steps -
First you need to download your device drivers and install it to your computer .
2. download Suvi rom from thred section
3. extract it in a folder
4. switch off your device , remove the bettery
5. press + and - volume and Power keys together .
6. install apx driver
7 . A popup sound cm
8 . place files in MTK TOOLS which you have extacted it in a folder and start the installation .
switch off the device after success .
Done . Enjoy your rooted device .. HIT THANKS
Sent from my Micromax A110 using xda premium
Click to expand...
Click to collapse
Hey Maddy,
Sorry but couldn't understand much out of this...... :crying: sorry but I said I am a newbie on this....
I want to know some exact steps to root and unroot.....
Thanks once again for replying.... (I have also hit Thanks )
Chin2 :silly:
) okay no problem .. i will do it remotly tomorrow .. ok .. you dont need to worry about it give me your team viewer ID here ..
Sent from my Micromax A110 using xda premium
maddyrokieasta said:
) okay no problem .. i will do it remotly tomorrow .. ok .. you dont need to worry about it give me your team viewer ID here ..
Sent from my Micromax A110 using xda premium
Click to expand...
Click to collapse
hi a very warm welcome to you into the xda family,
now that you are here i request you to please explore the community.
i am posting the solution for your problem, however i advice you that from now on before posting a query, or starting a thread, please go through the threads, as many problems have already been sorted and solutions are already there, moreover by going through the threads you will significantly increase ypur knowledge abt the device, etc
SO HERE IS YOUR SOLUTION
or all of those who are facing this problem, i am posting the link here follow the instructions given there,
1) http://d-h.st/zEb this is for the official mmx jb 1.11 rom
2) http://d-h.st/2Hn this is vcom drivers( download it and install it on your pc/laptop)
3) http://d-h.st/KyK this sp flash tool
4) http://linksredirect.com/?pub_id=562...ak733itivap95w THIS IS CWM RECOVERY FOR MMX A110( download this file on your computer and rename it " recovery.img" without quotes offcourse
5) http://linksredirect.com/?pub_id=562...erSU-v1.04.zip THIS is SU binaries
now to begin, first install mmx a110 drivers(connect your phone via usb now swithch off phone without disconnecting, wait for a few min drivers will be installed,) second download file no 2 (vcom drivers) install them on your pc/laptop
now if you have already flashed jb 1.11, then open sp flash tool, click scatter loading choose MT6577_android_scatter_emmc.txt, it will load everything , now deselect every option except recovery( very imp make sure u deselect every option except recovery) click on recovery and choose the file you downloaded in option 4( and renamed recovery.img)
now turn off your phone, take out the battery, and keep it aside,
in sp flash tools click download button(not firmware upgrade) after that connect your phone(in powered off battery rmoved state) via usb, and you will have cwm recovery.
now after flashing, close flash tool, disconnect phone and power up,
now transfer the files you downloaded in step 5, to your sd card. now switch off the phone, hold vol down +vol up+ power button, get into recovery follow instructions there and get into cwm recovery, now choose option install from sd card and go to the files you transferred to your sd card from pc(one u downloaded in step 5) and just install them, NOW GIV URSELF A HIGH FIVE YOU HAVE ROOTED UR MMX
FOR FURTHER ASSISTANCE YOU CAN REFFER TO THESE THREADS,
1) http://forum.xda-developers.com/show....php?t=2167244
2) https://www.google.co.in/url?sa=t&rc...N58fek2xrPmFQg
mohit141785 said:
hi a very warm welcome to you into the xda family,
now that you are here i request you to please explore the community.
i am posting the solution for your problem, however i advice you that from now on before posting a query, or starting a thread, please go through the threads, as many problems have already been sorted and solutions are already there, moreover by going through the threads you will significantly increase ypur knowledge abt the device, etc
SO HERE IS YOUR SOLUTION
or all of those who are facing this problem, i am posting the link here follow the instructions given there,
1) http://d-h.st/zEb this is for the official mmx jb 1.11 rom
2) http://d-h.st/2Hn this is vcom drivers( download it and install it on your pc/laptop)
3) http://d-h.st/KyK this sp flash tool
4) http://linksredirect.com/?pub_id=562...ak733itivap95w THIS IS CWM RECOVERY FOR MMX A110( download this file on your computer and rename it " recovery.img" without quotes offcourse
5) http://linksredirect.com/?pub_id=562...erSU-v1.04.zip THIS is SU binaries
now to begin, first install mmx a110 drivers(connect your phone via usb now swithch off phone without disconnecting, wait for a few min drivers will be installed,) second download file no 2 (vcom drivers) install them on your pc/laptop
now if you have already flashed jb 1.11, then open sp flash tool, click scatter loading choose MT6577_android_scatter_emmc.txt, it will load everything , now deselect every option except recovery( very imp make sure u deselect every option except recovery) click on recovery and choose the file you downloaded in option 4( and renamed recovery.img)
now turn off your phone, take out the battery, and keep it aside,
in sp flash tools click download button(not firmware upgrade) after that connect your phone(in powered off battery rmoved state) via usb, and you will have cwm recovery.
now after flashing, close flash tool, disconnect phone and power up,
now transfer the files you downloaded in step 5, to your sd card. now switch off the phone, hold vol down +vol up+ power button, get into recovery follow instructions there and get into cwm recovery, now choose option install from sd card and go to the files you transferred to your sd card from pc(one u downloaded in step 5) and just install them, NOW GIV URSELF A HIGH FIVE YOU HAVE ROOTED UR MMX
FOR FURTHER ASSISTANCE YOU CAN REFFER TO THESE THREADS,
1) http://forum.xda-developers.com/show....php?t=2167244
2) https://www.google.co.in/url?sa=t&rc...N58fek2xrPmFQg
Click to expand...
Click to collapse
Thanks Mohit,
You have provided me a best solution and I was able to follow it very quickly thanks once again.
I still want to ask about unrooting it again. Tell me the steps for the same if you can please help me out with this.
so nice of you.
Regards,
Chin2. :silly:
chin2h said:
Thanks Mohit,
You have provided me a best solution and I was able to follow it very quickly thanks once again.
I still want to ask about unrooting it again. Tell me the steps for the same if you can please help me out with this.
so nice of you.
Regards,
Chin2. :silly:
Click to expand...
Click to collapse
if you want to unroot just flash the official mmx update via sp flash tool. and your pfone will be stored to factory condition
Can u pls explain the process with screenshots that how to unroot canvas2 to official jellybean??
Sent from my Micromax A110 using XDA Premium 4 mobile app
hii all i am megatron007 from canvas hd forum now i will be working wid degrus for canvas doodle 2 roms from now these forum will be with a lots of rom thanx 1 rom is releasing today cheers !! :highfive:
Thanx for your job ! But for the lewa os rom can you put the french language because i'm french ...?
Bagoul said:
Thanx for your job ! But for the lewa os rom can you put the french language because i'm french ...?
Click to expand...
Click to collapse
yes i will put in next build
Megatron007 said:
yes i will put in next build
Click to expand...
Click to collapse
When you will be available?
Megatron007 said:
hii all i am megatron007 from canvas hd forum now i will be working wid degrus for canvas doodle 2 roms from now these forum will be with a lots of rom thanx 1 rom is releasing today cheers !! :highfive:
Click to expand...
Click to collapse
Can you also provide original firmaware and steps to install it in case i want to get back to original rom after installing custom rom.
tushargupta said:
Can you also provide original firmaware and steps to install it in case i want to get back to original rom after installing custom rom.
Click to expand...
Click to collapse
yes sure i will give steps
Megatron007 said:
yes sure i will give steps
Click to expand...
Click to collapse
Desperately waiting for it so that i can install the custom rom.:fingers-crossed:
Not able to flash custom rom on my canvas doodle 2 when tries it gave error .i am not able to find wipe davlic cache option in recovery mode even after rooting the phone. Can this be the reason? If yes than how to solve it. Thanks in advance.
Have you Installed CWM Recovery ?
tushargupta said:
Not able to flash custom rom on my canvas doodle 2 when tries it gave error .i am not able to find wipe davlic cache option in recovery mode even after rooting the phone. Can this be the reason? If yes than how to solve it. Thanks in advance.
Click to expand...
Click to collapse
Have you Installed CWM Recovery ?
If no... please install it via SP Flash Tools or MobileUncle..
Recovery.img is attached here....
Steps to be followed:-
1. Download Recovery.img and copy to root of phone.
2. Install Mobile Uncle Tools from Google Play store
3. Select Flash Recovery From SdCard option from MobileUncle Tools
4. Select Recovery.img... Flash... Reboot...
5. Enjoy new freedom... for flashing custom rom's.
hit Thanks if i have helped...
Megatron007 said:
hii all i am megatron007 from canvas hd forum now i will be working wid degrus for canvas doodle 2 roms from now these forum will be with a lots of rom thanx 1 rom is releasing today cheers !! :highfive:
Click to expand...
Click to collapse
Problems which I faced is the pure white keyboard ; camera not working ; audio profile not working
dark side expera ultimate rom not working. noting happens after installing rom it does not go beyod the experia logo.
defy403 said:
Have you Installed CWM Recovery ?
If no... please install it via SP Flash Tools or MobileUncle..
Recovery.img is attached here....
Steps to be followed:-
1. Download Recovery.img and copy to root of phone.
2. Install Mobile Uncle Tools from Google Play store
3. Select Flash Recovery From SdCard option from MobileUncle Tools
4. Select Recovery.img... Flash... Reboot...
5. Enjoy new freedom... for flashing custom rom's.
hit Thanks if i have helped...
Click to expand...
Click to collapse
Can you help me in installing stock rom back to my phone.
follow below steps
tushargupta said:
Can you help me in installing stock rom back to my phone.
Click to expand...
Click to collapse
Do you have Stock rom?
If yes...
Flash it via latest SP Flash Tool...
1. Switchoff your phone..
2. Open SP Flash Tools..
3. Select scartter file... from stock rom folder
4. select firmware upgrade option..
5. click on download...
6. now attach your phone with computer.. don't switch it on....
7. if you have all drivers installed .. i.e. mtk65xx pre-loader, vcom drivers... then flashing shuould start and complete in 5 mins....
8. keep your box of phone handy along with MTK Droid Tools 2.5.3 as you may need to restore your IMEI number...
hit thanks if i helped.. and ask if have any doubts...
---------- Post added at 01:08 PM ---------- Previous post was at 01:05 PM ----------
tushargupta said:
dark side expera ultimate rom not working. noting happens after installing rom it does not go beyod the experia logo.
Click to expand...
Click to collapse
Try This Experia ROM... i ported from a MMX A116 ... 4.4.2....
https://dl.dropboxusercontent.com/u/51418011/Defy403/A240 ROMs/Xperia_Z2_Port_A240.zip
give feedback...
defy403 said:
Do you have Stock rom?
If yes...
Flash it via latest SP Flash Tool...
1. Switchoff your phone..
2. Open SP Flash Tools..
3. Select scartter file... from stock rom folder
4. select firmware upgrade option..
5. click on download...
6. now attach your phone with computer.. don't switch it on....
7. if you have all drivers installed .. i.e. mtk65xx pre-loader, vcom drivers... then flashing shuould start and complete in 5 mins....
8. keep your box of phone handy along with MTK Droid Tools 2.5.3 as you may need to restore your IMEI number...
hit thanks if i helped.. and ask if have any doubts...
---------- Post added at 01:08 PM ---------- Previous post was at 01:05 PM ----------
Try This Experia ROM... i ported from a MMX A116 ... 4.4.2....
https://dl.dropboxusercontent.com/u/51418011/Defy403/A240 ROMs/Xperia_Z2_Port_A240.zip
give feedback...
Click to expand...
Click to collapse
I found following problems in the ROM:
1. Resolution of camera is limited to 6M
2. Camera not detecting internal SD so not working.
3.not able to install any app from play store because of SD card prob.
4. On boot first Sony xperia z2 is shown than boot logo of doodle comes if logo of doodle can be removed than it will look great.
Kindly help me in installing mtk driver. First I will like to confirm that can I use them in windows 8. Problem I am facing is when I connected my phone in switch off condition mtk preloaded was flashed in device manager but as soon as charging starts it disappeared.
please see the attached... drivers
tushargupta said:
Kindly help me in installing mtk driver. First I will like to confirm that can I use them in windows 8. Problem I am facing is when I connected my phone in switch off condition mtk preloaded was flashed in device manager but as soon as charging starts it disappeared.
Click to expand...
Click to collapse
1. Install these drivers... VCOM first... before connecting your device... and use MT65xx to upgrade drivers if you see your device already installed on device manager
2. Click Install drivers anyway... if you get a security prompt...
3. completely switch off... device... wait for 2 minutes...
4. Start SP Flash Tools... Load Scartter File....
5. Select.. Firmware Upgrade... click download...
6. Attach phone to pc... now all should be fine....
7. windows 8 should not be a major issue... i have win 7... but yes... can not test it... so can not promise...
tushargupta said:
I found following problems in the ROM:
1. Resolution of camera is limited to 6M
2. Camera not detecting internal SD so not working.
3.not able to install any app from play store because of SD card prob.
4. On boot first Sony xperia z2 is shown than boot logo of doodle comes if logo of doodle can be removed than it will look great.
Click to expand...
Click to collapse
Will you remove the bugs in your rom and repost it. I really like the interface of your ported rom.
Darkside Zyvex Rom
Megatron007 said:
hii all i am megatron007 from canvas hd forum now i will be working wid degrus for canvas doodle 2 roms from now these forum will be with a lots of rom thanx 1 rom is releasing today cheers !! :highfive:
Click to expand...
Click to collapse
I have installed the Darkside Zyvex rom and it runs great.
UI is very good,feels like using kitkat but there are some bugs like the audio profiles does not open, camera app not working and the icons are a little big and also apps don't move to SD card. Please can you fix them?
When multilanguage ROM will it be available?
tushargupta said:
Problems which I faced is the pure white keyboard ; camera not working ; audio profile not working
Click to expand...
Click to collapse
I have also installed the Zyvex Rom, facing the same problems, :crying:
Hope Megatron007 fix all the bugs soon. :angel:
Need Help LAVA iris 504q+
Please provide the stock rom for lava iris 504q plus
i have bricked my phone and need it urgently
Stock rom
downloadwww31.adrive.com/public/view/Rpt2ww.html
Link doesnt work
Please provide another link
will that work?
shubham56 said:
Link doesnt work
Please provide another link
Click to expand...
Click to collapse
is the stock recovery working dude??
sophisticatedjoker said:
is the stock recovery working dude??
Click to expand...
Click to collapse
nah dude
bt i got cwm somehow working
plz post d rom i need it urgently
cwm
shubham56 said:
plz post d rom i need it urgently
Click to expand...
Click to collapse
post ur cwm package here ..i'll extract the rom from my device and give that to you
but u may need to remove the bootloader
u can install cwm via mtk droid tools...its easy
follow these steps
Things to necessary---
*Mtk droid tool
*Rooted phone
*usb driver must be installed
*enable usb debbuging
STEPS:-
* Connect your switched on rooted mtk device to your computer and open MTKDroid tool, the tool will recognise your device and connect to it, if the colour indicator in the bottom left corner is green, you already have root shell,and can go on to the next step, if it is yellow, click on the root button at the bottom, and wait for the progress. When the indicator turns to green you have root shell which is necessary for this operation.
* Next click on the tab 'root,backup,recovery' and select 'to use boot from phone' then click on 'recovery and boot' and shortly after a dialogue box will appear asking if you want to 'make cwm recovery automatically' click yes.
* The tool will then create the recovery and another dialogue box will appear asking to 'install created recovery to phone', click yes.
*finally cwm has been installed.
shubham56 said:
u can install cwm via mtk droid tools...its easy
follow these steps
Things to necessary---
*Mtk droid tool
*Rooted phone
*usb driver must be installed
*enable usb debbuging
STEPS:-
* Connect your switched on rooted mtk device to your computer and open MTKDroid tool, the tool will recognise your device and connect to it, if the colour indicator in the bottom left corner is green, you already have root shell,and can go on to the next step, if it is yellow, click on the root button at the bottom, and wait for the progress. When the indicator turns to green you have root shell which is necessary for this operation.
* Next click on the tab 'root,backup,recovery' and select 'to use boot from phone' then click on 'recovery and boot' and shortly after a dialogue box will appear asking if you want to 'make cwm recovery automatically' click yes.
* The tool will then create the recovery and another dialogue box will appear asking to 'install created recovery to phone', click yes.
*finally cwm has been installed.
Click to expand...
Click to collapse
Hoe to root the phone in kitkat 4.4.2???
i tried framaroot,towelroot and kongo via PC
in framaroot it shows error 9
terrors94 said:
Hoe to root the phone in kitkat 4.4.2???
i tried framaroot,towelroot and kongo via PC
in framaroot it shows error 9
Click to expand...
Click to collapse
Check this out VROOT for PC
Download- http://www.mediafire.com/download/v3e3mtgxp1khlar/VRoot_1.6.0.3690_Setup.exe
root any phone in three steps
1>download ,install and open V Root
2>enable usb debugging and connect your phone
3>after it recognizes 504q+ click on root,it will reboot ur phone 3-4 times and when you see a 'TICK' sign
surprise surprise u have rooted ur phone
I m attaching my cwm package too
hope dis helps...
N dont forget to hit thanks if dis helps
Shubham is your phone rooted and is cwm installed pls help me too i also have 504q+
srb007 said:
Shubham is your phone rooted and is cwm installed pls help me too i also have 504q+
Click to expand...
Click to collapse
i have given the root guide on prev page
for cwm
download the cwm package
extract it and rename both files to recovery(retain the extensions)
copy to your sd card
download mobile uncle mtk tools
https://play.google.com/store/apps/details?id=com.mobileuncle.toolbox&hl=en
choose the recovery option
and select the copied recovery and press yes
done
kitkat update.zip require
shubham56 said:
i have given the root guide on prev page
for cwm
download the cwm package
extract it and rename both files to recovery(retain the extensions)
copy to your sd card
download mobile uncle mtk tools
https://play.google.com/store/apps/details?id=com.mobileuncle.toolbox&hl=en
choose the recovery option
and select the copied recovery and press yes
done
Click to expand...
Click to collapse
Shubham Can you provide me kitkat update.zip ??? i hav rooted and CWM installed ..........
Hi guys, I have rooted my 504q+ and installed carliv touch recovery, now I can't get kitkat update, please upload stock recovery img and kitkat update.
Thanks in advance.
Asking for password to download
nitish103 said:
downloadwww31.adrive.com/public/view/Rpt2ww.html
Click to expand...
Click to collapse
Hi dude,,, i am trying to flash this stock rom.... when i try to download it, its asking for password... please provide.....
shubham56 said:
Check this out VROOT for PC
Download- http://www.mediafire.com/download/v3e3mtgxp1khlar/VRoot_1.6.0.3690_Setup.exe
root any phone in three steps
1>download ,install and open V Root
2>enable usb debugging and connect your phone
3>after it recognizes 504q+ click on root,it will reboot ur phone 3-4 times and when you see a 'TICK' sign
surprise surprise u have rooted ur phone
I m attaching my cwm package too
hope dis helps...
N dont forget to hit thanks if dis helps
Click to expand...
Click to collapse
above setup file is in chiness.......do you have English version......Don't know how to root since can't understand language
Root by update-Su2.0.zip through cwm
Sent from my 504Q+ using Tapatalk
Any Developer Please Help us...
nitish103 said:
Root by update-Su2.0.zip through cwm
Sent from my 504Q+ using Tapatalk
Click to expand...
Click to collapse
How to root with this.... please provide steps or helpful link...
Any Developer please help us to ROOT Lava Iris 504Q+ after upgrading to KitKat 4.4.2
Please.....
need sctter file for iris504q+
Softbricked my phone as I was updating to 4.4.2 (>.<)
Can anyone plz give me scatter file so that I can flash cwm and restore my cwm backup
Any other help will be really great.
As I start my phone it just boots to stock recovery.
Just want to boot in cwm instead plz help.
This is How to Unbrick Lava Iris 504Q+
theprozaic said:
Softbricked my phone as I was updating to 4.4.2 (>.<)
Can anyone plz give me scatter file so that I can flash cwm and restore my cwm backup
Any other help will be really great.
As I start my phone it just boots to stock recovery.
Just want to boot in cwm instead plz help.
Click to expand...
Click to collapse
Bro.... download the STOCK ROM of 4.2.2 from here...
http://androidxda.com/download-lava-stock-rom-firmware
and follow the instructions given there to flash it manually...... Done.... your phone is back with all out of the box features.......
Give me a THANKS if i Helped....... :good:
Installing Clockworkmod Recovery on your Micromax Unite 2 means that you will be able to flash new custom ROMs on it. Without custom recovery you cannot flash new ROMs. Also, it should be installed on rooted devices. Clockworkmod Recovery can also be used to backup your entire ROM.
MODEDIT: ALL LINKS REMOVED DUE TO BEING PAYPERCLICK REDIRECTS
METHOD A (WITHOUT PC):
You need:
1. CWM recovery
a) For Kitkat (Download)
b) For Jellybean (Download)
2. MobileUncle tools (install from play store)
3. Rooted Phone (How to root | Root without PC)
Follow these steps to flash custom recovery without PC:
Step 1: Put downloaded recovery in external SD card.
Step 2: Install Mobileuncle tools.
Step 3: Open Mobileuncle tools.
Step 4: If asked grant root permission.
Step 5: Open Recovery Update.
Step 6: Choose the recovery you want to flash.
Step 7: Tap OK to confirm flashing recovery.
Step 8: Tap OK to reboot to newly flashed recovery.
METHOD B (PC):
You need:
1. CWM recovery
a) Kitkat (Download)
b) Jellybean (Download)
2. SP Flash tools (Download)
3. Scatter file (Create)
4. Micromax Unite 2/Myphone Rio Lite
Follow these steps to flash custom recovery using sp flash tools:
Step 1: Extract/unzip all downloaded files.
Step 2: Open SP flash tool and load scatter file.
Step 3: Unselect all blocks and select only RECOVERY.
Step 4: Click the location column of RECOVERY and select downloaded recovery.
Step 5: Remove battery of your phone, click Download in SP flash tool and connect your phone via USB cable (without battery).
My work:
[Repartition][Without pc] Increase apps storage in Micromax A106 Unite 2
CWM recovery for Micromax Unite 2 / Myphone Rio Lite
Recovery Flashable Stock ROM for Micromax A106 Unite 2
Hit Thanks :good: if i helped you..
mobileuncle mathod not working
bhai mobileuncle mathod is not working, actuly I increased the app memory with HK ROM editor. Maybe that's why its not working I don't have a pc bro help me out in this please okay !! thanks in advance
If you're facing any problem in mobileuncle tools then use flashify
Sent from my Micromax A106 using XDA mobile app
sreenshots
i dnt know in what method ( a or b ) the screennshot will be used...........i want to go with method A without pc......after clicking reboot to recovery what happen next......will my unite 2 show these scrren shot by clicking reboot to recovery........???
You can use either method A or method B. The screenshots are given to show how cwm recovery looks
Sent from my Micromax A106 using XDA mobile app
cwm files removed
Cwm recovery kitkat download link is not working.. It is showing files removed. Please upload it again... :highfive::cyclops:
Mobile uncle tools is not working.
Try 'recovery tools' (you can get it on play store)
comport problem on my pc
When I connecting my unite 2 phone to my pc without battery the comport is automatically disconnected what shuld I do and I install all drivers correctly plese reply me
Im in lollypop
From where i can get cwm recovery
What can ido for recovery mode in 5.0
Sent from my Micromax A106 using XDA Free mobile app
Can i use it for micromax a107
I have micromax a107. It has the same specifications as a106. Can i use this img file my phone, because i cant find any recovery file for a107. It is already rooted.
any screnshot of the rom
Is this recovey stable for cm based roms ported for unite 2?
rushabhdesai55 said:
I have micromax a107. It has the same specifications as a106. Can i use this img file my phone, because i cant find any recovery file for a107. It is already rooted.
Click to expand...
Click to collapse
No, the behavior of recovery.img depends on a lot of things like preloader, ik, boot
You can't use any other phone's recovery without porting it
---------- Post added at 08:27 AM ---------- Previous post was at 08:25 AM ----------
sameersssam said:
When I connecting my unite 2 phone to my pc without battery the comport is automatically disconnected what shuld I do and I install all drivers correctly plese reply me
Click to expand...
Click to collapse
Well, depends on what r u tryng 2 do, if u tryng 2 flash smthing with SPFT, click the download button before connecting
---------- Post added at 08:28 AM ---------- Previous post was at 08:27 AM ----------
Rajeshajith11 said:
Im in lollypop
From where i can get cwm recovery
Click to expand...
Click to collapse
Stable TWRP is available
onlyaliallowed said:
bhai mobileuncle mathod is not working, actuly I increased the app memory with HK ROM editor. Maybe that's why its not working I don't have a pc bro help me out in this please okay !! thanks in advance
Click to expand...
Click to collapse
How u increase your ROM with HK ROM Editor..... Plz help me I have a problem
shivambro said:
How u increase your ROM with HK ROM Editor..... Plz help me I have a problem
Click to expand...
Click to collapse
Just install the app rest it's UI is simple...
ChahatGupta said:
Just install the app rest it's UI is simple...
Click to expand...
Click to collapse
Ohh thank but when I do this my phone is off
shivambro said:
Ohh thank but when I do this my phone is off
Click to expand...
Click to collapse
Yeah obviously it'll reboot
ChahatGupta said:
Yeah obviously it'll reboot
Click to expand...
Click to collapse
Thank u so much ....
shivambro said:
Thank u so much ....
Click to expand...
Click to collapse
http://forum.xda-developers.com/android/software/mod-t3430353/