Hi,
I am trying to make custom mtd module, to expand the mtd devices to read whole nand and i am using as an example msm_nand.c
So what i have done is added a few devices to mtd partition and compiled. But at the compilation ld says msm_dmov_exec_cmd in not found.. Does not sound good, because original msm_nand.c compiled good as well as the whole kernel.
Could someone help me?
Here is the code i added, i left last lines from the original and my addition due to the code length restriction here:
Code:
/* drivers/mtd/devices/msm_nand.c
.....
msm_nand_release_ex(&info->mtd);
dma_free_coherent(/*dev*/ NULL, SZ_4K,
info->msm_nand.dma_buffer,
info->msm_nand.dma_addr);
kfree(info);
}
return 0;
}
#define DRIVER_NAME "msm_nand_ex"
static struct platform_driver msm_nand_driver = {
.probe = msm_nand_probe,
.remove = __devexit_p(msm_nand_remove_ex),
.driver = {
.name = DRIVER_NAME,
}
};
MODULE_ALIAS(DRIVER_NAME);
#if defined(CONFIG_ARCH_MSM7X30)
#define MSM_NAND_PHYS 0xA0200000
#else
#define MSM_NAND_PHYS 0xA0A00000
#endif
static struct resource resources_nand[] = {
[0] = {
.name = "msm_nand_dmac",
.start = DMOV_NAND_CHAN,
.end = DMOV_NAND_CHAN,
.flags = IORESOURCE_DMA,
},
[1] = {
.name = "msm_nand_phys",
.start = MSM_NAND_PHYS,
.end = MSM_NAND_PHYS + 0x7FF,
.flags = IORESOURCE_MEM,
},
};
static struct mtd_partition nand_ex_partitions[] = {
{
.name = "bootloader",
.size = 0x00000016,
.offset = 0,
.mask_flags = MTD_WRITEABLE, /* force read-only */
}, {
.name = "amss",
.size = 0x000000bf,
.offset = 0x00000016,
.mask_flags = MTD_WRITEABLE, /* force read-only */
}, {
.name = "amss_fs",
.size = 0x00000058,
.offset = 0x000000d5,
.mask_flags = MTD_WRITEABLE, /* force read-only */
}, {
.name = "fota0",
.size = 0x00000022,
.offset = 0x0000012d,
.mask_flags = MTD_WRITEABLE, /* force read-only */
}, {
.name = "fota1",
.size = 0x00000022,
.offset = 0x0000014f,
.mask_flags = MTD_WRITEABLE, /* force read-only */
}, {
.name = "recovery",
.size = 0x00000062,
.offset = 0x00000171,
.mask_flags = MTD_WRITEABLE, /* force read-only */
}, {
.name = "dsp1",
.size = 0x000000a2,
.offset = 0x000001d3,
.mask_flags = MTD_WRITEABLE, /* force read-only */
}, {
.name = "boot",
.size = 0x00000062,
.offset = 0x00000275,
.mask_flags = MTD_WRITEABLE, /* force read-only */
}
};
struct flash_platform_data msm_nand_ex_data = {
.parts = nand_ex_partitions,
.nr_parts = ARRAY_SIZE(nand_ex_partitions),
};
static struct platform_device *msm_device_nand_ex;
static int __init msm_nand_init(void)
{
int ret;
msm_device_nand_ex = platform_device_alloc("msm_nand_ex", -1);
if (!msm_device_nand_ex)
return -ENOMEM;
ret = platform_device_add_data(msm_device_nand_ex, &msm_nand_ex_data,
sizeof(msm_nand_ex_data));
ret = platform_device_add_resources(msm_device_nand_ex, resources_nand,
ARRAY_SIZE(resources_nand));
printk("%s : res=%d\n", __FUNCTION__, ARRAY_SIZE(resources_nand));
if (ret == 0)
ret = platform_device_add(msm_device_nand_ex);
if (ret){
platform_device_put(msm_device_nand_ex);
return ret;
}
return platform_driver_register(&msm_nand_driver);
}
static void __exit msm_nand_exit(void)
{
platform_driver_unregister(&msm_nand_driver);
platform_device_unregister(msm_device_nand_ex);
}
module_init(msm_nand_init);
module_exit(msm_nand_exit);
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("msm_nand flash driver code");
And also i get in dmesg weird message that my kernel version string is wrong, though i used same kernel except the last modification string. And i can't find any other kernel..
Thanks guys!
you should edit the Makefile and set
EXTRAVERSION = <your kernel version>.
Yes i managed to bypass it but the insmod then says msm_dmov_exec_cmd is not found..
Weird..
anonymous2183 said:
you should edit the Makefile and set
EXTRAVERSION = <your kernel version>.
Click to expand...
Click to collapse
This is a program that I wrote to decode the newer style "logo.bin" files used in some OPPO, and OnePlus devices. Please read below so you can better understand this type of encoding being used:
What Is A Raw Image?
A raw image, whether it be a file or an image in memory, is simply pixel data. There is no extra information like width, height, name, end of line... Absolutely nothing, just pixel data. If you have an image that is raw and the resolution is 1080x1920 and you are using a typical RGB24 or BGR24 (like the ones used here), then your exact filesize or size in memory will be 1080x1920x3! We use 3 here because there is one byte for the R or red component, one for the G (green), and one for the B(blue).
What Is A Run Length Encoded Image?
A run length image encoding uses a count ;usually a single byte (char), 2 bytes (short int), or 4 bytes (long int); and then the pixel components. So instead of writing out 300 bytes of '0's to make a line of 100 black pixels. Black is RGB(0,0,0). You could encode this as 100, 0, 0, 0. And only use 4 bytes of data to get the exact same image as the 300 byte raw image. All the run length encoding I've found, except the Motorola style which is a little different, use a run length encoding that is pixel-oriented like this.
Now I've figured out this new one and it is a byte-oriented run length encoding. This is for runs of bytes, not pixels. You may think, well whats the big deal? When you add a little area of color, you increase the run length encoded image in you logo.bin immensely! You use 6 bytes per pixel if there aren't any runs of color data. If you had an image that was a 1080x1920 black image with a 25 pixel wide, by 25 pixel high red box in the middle. The encoder would be doing runs of black data efficiently until it reached the red area.
.....0 255 0 255 0 255 0 255 0 255 0 99 /// we've reached the top left corner of the red square /// 13 1 30 1 255 1 // << that was just one red pixel!! in bgr color order (13, 30, 255) <<// And it keeps going through the rest of the red pixels on that line using 6 bytes per pixel, which is the opposite of compression. Before reaching the red square the encoding was decoding to 255 zeros over and over, until finally 99 zeros. 255 zeros is 85 black pixels stored in just 2 bytes!
This type of encoding is only good for grey scale images. It is not good with color, but it still will handle color of course. In grey scale, the Red, Blue, and Green data components are always the same values. All the way from black (0,0,0) to white (255, 255, 255); including every shade of grey in between>>>(1,1,1) (2,2,2) (3,3,3)....(253, 253, 253) (254, 254, 254)<<<
One other difference in this method of run length encoding is that the color byte is before the count, which is backwards from all of the other methods.
The attachment contains the C source code (which is also in the 2nd post) and the executable that was compiled using mingw32 on a 64 bit Windows 7 PC. The PNG library that I used is LodePng, the source is in the download.
To use logoinjector:
Decode your logo.bin:
Code:
logoInjector.exe -i logo.bin -d
All the PNG 's will be extracted from logo.bin. Edit the PNGs that you want to change...
Note:
Your original "logo.bin" file is never changed, it is just read. If the file you try to load isn't a logo.bin file, or if it is the older style, then the program will tell you and exit
Inject the image(s) back in to the logo.bin:
Code:
logoinjector.exe -i logo.bin -j image_name_1 image_name_3....
To list whats in your logo file:
Code:
logoinjector.exe -i logo.bin -l
For a more detailed list:
Code:
logoinjector.exe -i logo.bin -L
If the colors are messed up use the "-s" switch while decoding.
Code:
logoinjector.exe -i logo.bin -d -s
If you had to use the "-s" switch to decode properly, you'll have to use it to inject also:
Code:
logoinjector.exe -i logo.bin -j image_name -s
Note:
With version 1.2, you can put as many names after "-j" as you want, and it's not case sensitive. You also don't have to put the whole name. If you just put "-j fhd" every image in the logo.bin that starts with "fhd" will be injected. There has to be a PNG with the name in the directory though
The size of your modified.logo.bin will displayed along with the original size, if everything went good. Please know the size of you logo partition. I made this program to encompass any device using this format, and there is no set size of the logo partition between devices. Fastboot will just error out if you try to flash data bigger than the partition before it writes anything. But if someone gets brave and tries to "DD" to the logo partition, it could get ugly.:cyclops:
Flash the "modified.logo.bin" file through fastboot.
v1.2
made it possible for multiple injections in one command
doesn't add png to the decoded png if it was already in the name
fixed out of scope with image 26 in OPPO find 7 logo.bin
added LodePng source in the download
made the default color order BGR
displays the modified logo file size as well as the original file size
runs the modified.logo.bin back through the list function after injecting
checks the number of offsets between the original and modified logo.bin
Use this at your own risk.
Always make backups.
Always.
Code:
/*
/*
* Logo Injector v1.2
*
* Copyright (C) 2015 Joseph Andrew Fornecker
* makers_mark @ xda-developers.com
* [email protected]
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 3 of the License, or (at your
* opinion) any later version. See <http://www.gnu.org/licenses/gpl.html>
*
* New in v1.2:
*
* - Fixed out of scope crash involving image #26 in oppo find 7 logo.bin (26 IS BIG)
* - Multiple injection names possible after the -j parameter
* - Injection names are now case insensitive
* - BGR is the the default color order, instead of RGB
* - Added more error checks
* - Show the change in file size of original logo.bin compare to the modified logo.bin
* - Several small changes dealing with readability
*/
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <string.h>
#include <stdint.h>
#include "lodepng.h"
#define SWAP32(x) (( x >> 24 )&0xff) | ((x << 8)&0xff0000) | ((x >> 8)&0xff00) | ((x << 24)&0xff000000)
#define BLOCK 512
#define OFFSETSTART 48
#define BYTESPERPIXEL 3
#define MAXOFFSETS 28
#define SIZEOFLONGINT 4
#define TWOTOTHETEN 1024
typedef struct {
uint8_t header[8];
uint8_t blank[24];
uint32_t width;
uint32_t height;
uint32_t lengthOfData;
uint32_t special;
uint32_t offsets[MAXOFFSETS];
uint8_t name[64];
uint8_t metaData[288];
} IMAGEHEAD;
uint16_t Copy(FILE *, IMAGEHEAD *, uint16_t , uint16_t, FILE *);
int32_t InjectNewStyle(FILE *, IMAGEHEAD *, uint16_t , uint8_t *, uint16_t, FILE *, uint32_t * );
int32_t RewriteHeaderZero( uint32_t , uint16_t, FILE* , int32_t, uint32_t * );
uint32_t Encode(uint8_t*, uint8_t*, uint32_t);
uint32_t GetEncodedSize(uint8_t*, uint32_t);
uint32_t GetWidth(FILE*);
uint32_t GetHeight(FILE*);
uint64_t BlockIt(uint32_t);
uint16_t GetNumberOfOffsets(FILE*);
int32_t DecodeLogoBin(FILE*, IMAGEHEAD *);
int32_t ListFileDetails(FILE*, IMAGEHEAD *);
uint8_t* Decode(FILE*, uint32_t, uint32_t, uint32_t, uint8_t*);
int32_t IsItTheNewStyle(FILE*);
IMAGEHEAD* ParseHeaders(FILE*, uint16_t);
int32_t IsItALogo(FILE*);
void PrintFileSize(uint32_t);
uint32_t GetFileSize(FILE *);
uint16_t badAss = 0;
int16_t rgb2bgr = 1;
uint16_t convertToPNG = 1;
uint8_t HEADER[] = {0x53,0x50,0x4C,0x41,0x53,0x48,0x21,0x21};
int32_t IsItALogo(FILE *originalLogoBin){
uint8_t string[9];
uint16_t i;
fread(string, 1, 8, originalLogoBin);
for (i = 0 ; i < 8 ; i++){
if (string[i] == HEADER[i]){
continue;
} else {
return 0;
}
}
return 1;
}
int32_t IsItTheNewStyle(FILE *originalLogoBin){
int32_t newStyle = 0;
fread(&newStyle, 1, SIZEOFLONGINT, originalLogoBin);
if (newStyle == 0){
return 1;
} else {
return 0;
}
}
IMAGEHEAD *ParseHeaders(FILE *originalLogoBin, uint16_t numberOfOffsets){
uint8_t i = 0;
IMAGEHEAD *imageHeaders;
imageHeaders = malloc(BLOCK * numberOfOffsets);
memset(imageHeaders, 0, BLOCK * numberOfOffsets);
fseek(originalLogoBin, 0, SEEK_SET);
fread(&imageHeaders[i], 1 , BLOCK, originalLogoBin);
for ( i = 1 ; i < numberOfOffsets ; ++i ){
fseek(originalLogoBin, imageHeaders[0].offsets[i], SEEK_SET);
fread(&imageHeaders[i], 1 , BLOCK, originalLogoBin);
}
return imageHeaders;
}
uint16_t GetNumberOfOffsets(FILE *originalLogoBin){
uint16_t i = 0;
uint32_t readAs = 0;
fseek(originalLogoBin, OFFSETSTART, SEEK_SET);
while(i < MAXOFFSETS){
fread(&readAs, 1, SIZEOFLONGINT, originalLogoBin);
if ((readAs == 0) && (i != 0)){
break;
} else {
i++;
}
}
return i;
}
uint8_t* Decode(FILE *originalLogoBin, uint32_t start, uint32_t length, uint32_t imageBytes, uint8_t* image){
uint32_t decodedBytes = 0, i = 0;
uint8_t* data;
fseek(originalLogoBin, start, SEEK_SET);
data = (uint8_t*)malloc(length);
if (fread(data, 1, length, originalLogoBin) != length) {
fprintf(stderr, "Could not read file!!\n");
exit(0);
}
while((i < length) && (decodedBytes < imageBytes)){
memset(&image[decodedBytes], data[i], (data[i + 1]));
decodedBytes += (uint8_t)data[i+1];
i += 2;
if ((i < length) && (imageBytes - decodedBytes < (uint8_t)data[i + 1])){
memset(&image[decodedBytes], data[i], imageBytes - decodedBytes);
decodedBytes = imageBytes;
fprintf(stdout, "More information was in encoding than resolution called for.\n");
break;
}
}
fprintf(stdout, "%ld decoded bytes\n", decodedBytes);
free(data);
if( rgb2bgr == 1 ){
uint8_t old;
i = 0;
while( i < imageBytes){
old = image[i];
memset(&image[i], image[i + 2], 1);
memset(&image[i + 2], old, 1);
i += BYTESPERPIXEL;
}
}
return image;
}
int32_t DecodeLogoBin(FILE *originalLogoBin, IMAGEHEAD *imageHeaders){
uint32_t size, imageBytes, start;
uint8_t* image;
uint8_t name[65];
uint8_t r = 0;
uint16_t i , numberOfOffsets = GetNumberOfOffsets(originalLogoBin);
for ( i = 0 ; i < numberOfOffsets ; i++ ){
fprintf(stdout,"\n\n\n#%d: Offset:%ld\n", i + 1, imageHeaders[0].offsets[i]);
if ((imageHeaders[i].width == 0) || (imageHeaders[i].height == 0)){
fprintf(stdout, "Placeholder for %s\n", imageHeaders[i].metaData);
continue;
}
fprintf(stdout, "Header=%s\nWidth=%ld\nHeight=%ld\nData Length=%ld\nSpecial=%ld\nName=%s\nMetadata=%s\n",
imageHeaders[i].header, imageHeaders[i].width, imageHeaders[i].height,
imageHeaders[i].lengthOfData, imageHeaders[i].special, imageHeaders[i].name, imageHeaders[i].metaData);
if (convertToPNG){
start = imageHeaders[0].offsets[i] + BLOCK;
imageBytes = imageHeaders[i].width * (imageHeaders[i].height) * BYTESPERPIXEL;
image = malloc(imageBytes);
uint8_t lengthOfName = strlen(imageHeaders[i].name);
uint8_t *ext;
ext = strrchr(imageHeaders[i].name, '.');
if (((ext[1] == 'p') || (ext[1] == 'P')) &&
((ext[2] == 'n') || (ext[2] == 'N')) &&
((ext[3] == 'g') || (ext[3] == 'G')) &&
((ext[0] == '.'))){
sprintf(name, "%s", imageHeaders[i].name);
} else {
sprintf(name, "%s.png", imageHeaders[i].name);
}
lodepng_encode24_file(name, Decode(originalLogoBin, (uint32_t)start, (uint32_t)imageHeaders[i].lengthOfData, (uint32_t)imageBytes, image) , (unsigned)imageHeaders[i].width, (unsigned)imageHeaders[i].height);
free(image);
}
}
return 0;
}
int32_t ListFileDetails(FILE *originalLogoBin, IMAGEHEAD *imageHeaders){
uint32_t i = 0, j = 0;
fseek(originalLogoBin, 0, SEEK_SET);
uint16_t numberOfOffsets = GetNumberOfOffsets(originalLogoBin);
fprintf(stdout, "Resolution\tOffset\tName\n");
fprintf(stdout, "-------------------------------------------------------------\n");
for ( i = 0 ; i < numberOfOffsets ; i++ ){
if ((imageHeaders[i].width == 0) || (imageHeaders[i].height == 0)){
fprintf(stdout, "(placeholder) for %s\n", imageHeaders[i].metaData);
continue;
}
fprintf(stdout,"%dx%d\t", imageHeaders[i].width, imageHeaders[i].height);
if ((imageHeaders[i].width < 1000) && (imageHeaders[i].height <1000)){fprintf(stdout, "\t");}
fprintf(stdout, "%ld\t%s\n", imageHeaders[0].offsets[i], imageHeaders[i].name );
}
return 1;
}
uint16_t Copy(FILE *originalLogoBin, IMAGEHEAD *imageHeaders, uint16_t numberOfOffsets, uint16_t injectionNumber, FILE *modifiedLogoBin){
uint8_t *data;
uint32_t offset, originalOffset;
uint32_t imageSize = BlockIt(BLOCK + imageHeaders[injectionNumber].lengthOfData);
if( imageHeaders[injectionNumber].name[0] == 0){
fprintf(stdout, "Copying \t#%d:(placeholder) %s\n", injectionNumber + 1 , imageHeaders[injectionNumber].metaData);
} else {
fprintf(stdout, "Copying \t#%d:%s\n", injectionNumber + 1 , imageHeaders[injectionNumber].name);
}
data = malloc(imageSize);
memset(data, 0 , imageSize);
fread(data, 1, imageSize, originalLogoBin);
fwrite(data, 1 , imageSize, modifiedLogoBin);
free(data);
}
int32_t InjectNewStyle(FILE *originalLogoBin, IMAGEHEAD *imageHeaders, uint16_t numberOfOffsets, uint8_t *injectionName, uint16_t injectionNumber, FILE *modifiedLogoBin, uint32_t *ihMainOffsets ){
uint32_t encodedSize = 0, actualWritten = 0, imageSize = 0;
uint8_t *data, *header;
int8_t inFileName[69];
int32_t blockDifference;
uint32_t offset, originalOffset;
FILE *pngFile;
sprintf(inFileName, "%s", injectionName);
if (imageHeaders[injectionNumber].special != 1){
fprintf(stdout, "ERROR: \"Special\" is not equal to '1' \nThis would not be safe to flash!\nPlease email logo.bin in question to:\[email protected]\n");
fclose(originalLogoBin);
fclose(modifiedLogoBin);
return 0;
}
if ((pngFile = fopen(inFileName, "rb")) == NULL){
sprintf(inFileName, "%s.png", injectionName);
if ((pngFile = fopen(inFileName, "rb")) == NULL){
fclose(pngFile);
fclose(modifiedLogoBin);
fclose(originalLogoBin);
fprintf(stderr, "%s could not be read\n", inFileName);
return 0;
}
}
IMAGEHEAD new;
memset(new.blank, 0, sizeof(new.blank));
memset(new.metaData, 0, sizeof(new.metaData));
memset(new.offsets, 0, SIZEOFLONGINT * MAXOFFSETS);
strncpy(new.header, HEADER , 8);
strncpy(new.metaData, imageHeaders[injectionNumber].metaData, sizeof(imageHeaders[injectionNumber].metaData));
strncpy(new.name, injectionName, 64);
new.special = 1;
fprintf(stdout, "Injecting\t#%d:%s\n", injectionNumber + 1 , imageHeaders[injectionNumber].name);
if (((new.width = GetWidth(pngFile)) != imageHeaders[injectionNumber].width) && (!badAss)){
fprintf(stderr, "Error: Width of PNG to be injected is %d, it must be %d!\n", new.width, imageHeaders[injectionNumber].width);
fclose(pngFile);
fclose(modifiedLogoBin);
fclose(originalLogoBin);
return 0;
}
if (((new.height = GetHeight(pngFile)) != imageHeaders[injectionNumber].height) && (!badAss)){
fprintf(stderr, "Error: Height of PNG to be injected is %d, it must be %d!\n", new.height, imageHeaders[injectionNumber].height);
fclose(pngFile);
fclose(modifiedLogoBin);
fclose(originalLogoBin);
return 0;
}
uint32_t rawBytes = new.width * new.height * BYTESPERPIXEL;
uint8_t *decodedPNG = malloc(rawBytes);
lodepng_decode24_file(&decodedPNG, (uint32_t*)&new.width, (uint32_t*)&new.height , (const uint8_t*)inFileName);
if (rgb2bgr == 1){
uint8_t old;
uint32_t k = 0;
while( k < rawBytes ){
old = decodedPNG[k];
memset(&decodedPNG[k], decodedPNG[k + 2], 1);
memset(&decodedPNG[k + 2], old, 1);
k += BYTESPERPIXEL;
}
}
encodedSize = GetEncodedSize(decodedPNG, (new.width * new.height * BYTESPERPIXEL));
new.lengthOfData = encodedSize;
uint8_t *rlEncoded = malloc(BlockIt(encodedSize));
memset(rlEncoded, 0, BlockIt(encodedSize));
actualWritten = Encode(decodedPNG, rlEncoded, (new.width * new.height * BYTESPERPIXEL));
blockDifference = (((BLOCK + BlockIt(actualWritten)) - (BLOCK + BlockIt(imageHeaders[injectionNumber].lengthOfData))) / BLOCK);
fwrite(&new, 1 , BLOCK, modifiedLogoBin);
fwrite(rlEncoded, 1 , BlockIt(actualWritten), modifiedLogoBin);
free(decodedPNG);
free(rlEncoded);
RewriteHeaderZero( injectionNumber , numberOfOffsets , modifiedLogoBin , blockDifference, ihMainOffsets);
fclose(pngFile);
return 1;
}
int32_t RewriteHeaderZero( uint32_t injectionImageNumber , uint16_t numberOfOffsets, FILE *modifiedLogoBin , int32_t blockDifference, uint32_t *ihMainOffsets){
uint8_t i, j = injectionImageNumber + 1 ;
uint32_t filePosition = ftell(modifiedLogoBin);
uint32_t offset = 0;
for( ; j < numberOfOffsets; j++){
fseek(modifiedLogoBin, OFFSETSTART + (SIZEOFLONGINT * j), SEEK_SET);
offset = ihMainOffsets[j];
offset += (blockDifference * BLOCK);
fseek(modifiedLogoBin, OFFSETSTART + (SIZEOFLONGINT * j), SEEK_SET);
fwrite(&offset, 1 , SIZEOFLONGINT , modifiedLogoBin);
ihMainOffsets[j] = offset;
}
fseek(modifiedLogoBin, filePosition , SEEK_SET);
return;
}
uint32_t GetEncodedSize(uint8_t* data, uint32_t size){
uint32_t pos = 0, ret = 0;
uint16_t count = 1;
for( pos = 0 ; pos < size ; ++pos , count = 1){
while((pos < size - 1) && (count < 0xFF) && ((memcmp(&data[pos], &data[pos+1], 1)) == 0)){
count++;
pos++;
}
ret += 2;
}
return ret;
}
uint32_t Encode(uint8_t* rawRgbReading, uint8_t* rlEncoded, uint32_t rawSize){
uint32_t writePosition = 0 , readPosition = 0;
uint16_t count = 1;
for( readPosition = 0 ; readPosition < rawSize ; ++readPosition , count = 1){
while((readPosition < rawSize - 1 ) && (count < 0xFF) && ((memcmp(&rawRgbReading[readPosition], &rawRgbReading[readPosition+1], 1)) == 0)){
count++;
readPosition++;
}
rlEncoded[writePosition] = rawRgbReading[readPosition];
rlEncoded[writePosition + 1] = count;
writePosition += 2;
}
return writePosition;
}
uint32_t GetWidth(FILE *pngFile){
uint32_t width;
fseek(pngFile, 16, SEEK_SET);
fread(&width, 1, SIZEOFLONGINT, pngFile);
return(SWAP32(width));
}
uint32_t GetHeight(FILE *pngFile){
uint32_t height;
fseek(pngFile, 20, SEEK_SET);
fread(&height, 1, SIZEOFLONGINT, pngFile);
return(SWAP32(height));
}
uint64_t BlockIt(uint32_t isize){
uint32_t blockSize = BLOCK;
if ((isize % blockSize) == 0){
return isize;
}else{
return isize + (blockSize - (isize % blockSize));
}
}
void Usage(){
fprintf(stdout, "Usage: logoinjector -i \"input file\" [-l] | [-L] | [-d [-s]] | [-j \"image to be replaced\" [-b] | [-s]]\n\n");
fprintf(stdout, "Mandatory Arguments:\n\n");
fprintf(stdout, "\t-i \"C:\\xda\\logo.bin\"\n");
fprintf(stdout, "\t This is the logo.bin file to analyze or inject an image\n\n");
fprintf(stdout, "Optional Arguments:\n\n");
fprintf(stdout, "\t-d Decode all images into PNGs, (-s)wap parameter may be needed for proper color.\n");
fprintf(stdout, "\t-l Lower case 'L' is to display a short list of what is inside the input file.\n");
fprintf(stdout, "\t-L Upper case 'L' is for a more detailed list of logo.bin image contents.\n");
fprintf(stdout, "\t-b 'b' is used to tell the program to disregard width or height differences\n");
fprintf(stdout, "\t when encoding an image, the program also won't fail if it can't find a name\n");
fprintf(stdout, "\t that can't be found on the inject list when encoding images\n");
fprintf(stdout, "\t-s 's' is used to swap RGB and BGR color order. Can be used on decoding or encoding.\n");
fprintf(stdout, "\t NEW IN THIS V1.2: Swap is on by default, meaning the color order will be BGR. Using\n");
fprintf(stdout, "\t the \"-s\" switch will result in a RGB color order. Bottom line: If you (-d)ecode the\n");
fprintf(stdout, "\t images (that have color) and the colors aren't right, then you should use (-s) to \n");
fprintf(stdout, "\t decode and inject images.\n");
fprintf(stdout, "\t-j \"image(s) to be replaced\"\n");
fprintf(stdout, "\t The image(s) name to be replaced as seen in the (-l)ist\n");
fprintf(stdout, "\t NEW IN THIS V1.2: Multiple image names may be put after \"-j\"\n");
fprintf(stdout, "\t The names simply need to be separated by a space. The names now also are not case\n");
fprintf(stdout, "\t sensitive, and it doesn't matter if you put the extension at the end of the name.\n");
fprintf(stdout, "\t You actually only need to put the first characters of the name.\nExample:\n");
fprintf(stdout, "\t logoinjector -i \"your_logo.bin\" -j FHD \n\n");
fprintf(stdout, "\t This will inject a PNG for every name in the logo bin that begins with \"fhd\"\n");
return;
}
void PrintFileSize(uint32_t bytes){
float megaBytes = 0, kiloBytes = 0;
kiloBytes = (float)bytes / (float)TWOTOTHETEN;
megaBytes = kiloBytes / (float)TWOTOTHETEN;
if (kiloBytes < (float)TWOTOTHETEN){
fprintf(stdout, "\t%.2f KB\n", kiloBytes);
} else {
fprintf(stdout, "\t%.2f MB\n", megaBytes);
}
return;
}
uint32_t GetFileSize(FILE *temp){
fseek(temp, 0 , SEEK_END);
uint32_t fileSizeZ = ftell(temp);
return(fileSizeZ);
}
int32_t main(int32_t argc, int8_t **argv){
int32_t c;
int16_t h, i , j , k = 0;
FILE *originalLogoBin = NULL, *modifiedLogoBin = NULL;
uint8_t *inputFile = NULL;
uint8_t *injectNames[MAXOFFSETS];
int16_t decodeAllOpt = 0;
int16_t encodeOpt = 0;
int16_t inject = 0;
int16_t listFile = 0;
uint16_t numberOfOffsets = 0, injected = 0;
for(i = 0; i < MAXOFFSETS; i++){
injectNames[i] = NULL;
}
fprintf(stdout, "__________________________________________________________-_-\n");
fprintf(stdout, "Logo Injector v1.2\n\nWritten By Makers_Mark @ XDA-DEVELOPERS.COM\n");
fprintf(stdout, "_____________________________________________________________\n\n");
while ((c = getopt (argc, (char**)argv, "sSj:J:hHbBdDlLi:I:")) != -1){
switch(c)
{
case 'l':
listFile = 1;
break;
case 'L':
decodeAllOpt = 1;
convertToPNG = 0;
break;
case 'i':
case 'I':
inputFile = optarg;
break;
case 'b':
case 'B':
badAss = 1;
break;
case 'j':
case 'J':
h = optind - 1 ;
uint8_t *nextArg;
while(h < argc){
inject = 1;
nextArg = strdup(argv[h]);
h++;
if(nextArg[0] != '-'){
injectNames[k++] = nextArg;
} else {
break;
}
}
optind = h - 1;
break;
case 'd':
case 'D':
decodeAllOpt = 1 ;
break;
case 's':
case 'S':
rgb2bgr = -1 ;
break;
case 'h':
case 'H':
Usage();
return 0;
break;
default:
Usage();
return 0;
break;
}
}
if (inputFile == NULL){
Usage();
return 0;
}
fprintf(stdout, "FILE: %s\n_____________________________________________________________\n\n", inputFile);
if (rgb2bgr == 1){
fprintf(stdout, "BGR is the color order. Use \"-s\" switch to change it to RGB.\n\n");
} else {
fprintf(stdout, "RGB is the color order. Use \"-s\" switch to change it to BGR.\n\n");
}
if ((originalLogoBin = fopen(inputFile, "rb")) == NULL){
fprintf(stderr, "%s could not be opened\n", inputFile);
return 0;
}
if (!IsItALogo(originalLogoBin)){
fprintf(stdout, "\nThis is NOT a valid Logo.bin\n\n");
fclose(originalLogoBin);
return 0;
}
if (!IsItTheNewStyle(originalLogoBin)){
fprintf(stdout, "\nThis is the old style logo.bin\n\n");
fclose(originalLogoBin);
return 0;
}
numberOfOffsets = GetNumberOfOffsets(originalLogoBin);
IMAGEHEAD *imageHeaders = ParseHeaders(originalLogoBin, numberOfOffsets);
if (listFile){
ListFileDetails(originalLogoBin, imageHeaders);
return 1;
}
if(inject){
uint32_t ihMainOffsets[MAXOFFSETS];
uint8_t found = 0, exitFlag = 0;
for (i = 0; i < MAXOFFSETS ; i++){
ihMainOffsets[i] = 0;
}
for (j = 0; j < k ; j++){
for (i = 0 ; i < numberOfOffsets ; i++ ){
if((strcasecmp(imageHeaders[i].name, injectNames[j]) == 0) ||
(strncasecmp(imageHeaders[i].name, injectNames[j], strlen(injectNames[j])) == 0)){
found = 1;
break;
} else {
found = 0;
}
}
if (!found){
fprintf(stdout, "ERROR: \"%s\" is not in the logo bin !!!!\n", injectNames[j]);
exitFlag = 1;
}
}
if ((exitFlag) && (!badAss)){
fclose(originalLogoBin);
exit(0);
}
memcpy(&ihMainOffsets , &imageHeaders[0].offsets, SIZEOFLONGINT * MAXOFFSETS);
fseek(originalLogoBin, 0, SEEK_SET);
if ((modifiedLogoBin = fopen("modified.logo.bin", "wb+")) == NULL){
fclose(modifiedLogoBin);
fclose(originalLogoBin);
fprintf(stderr, "modified.logo.bin could not be opened\n");
return 0;
}
for (i = 0 ; i < numberOfOffsets ; i++ , injected = 0 ){
for (j = 0; j < k ; j++){
if((strcasecmp(imageHeaders[i].name, injectNames[j]) == 0) ||
(strncasecmp(imageHeaders[i].name, injectNames[j], strlen(injectNames[j])) == 0)){
if (InjectNewStyle(originalLogoBin, imageHeaders , numberOfOffsets, imageHeaders[i].name, i, modifiedLogoBin, ihMainOffsets) == 0){
fprintf(stderr, "Error: Injecting %s\n", imageHeaders[i].name);
fclose(originalLogoBin);
fclose(modifiedLogoBin);
return 0;
}
if ( i != numberOfOffsets - 1 ){
fseek(originalLogoBin, imageHeaders[0].offsets[i+1], SEEK_SET);
}
injected = 1;
break;
}
}
if (!injected){
Copy(originalLogoBin , imageHeaders, numberOfOffsets, i, modifiedLogoBin);
}
}
uint16_t modifiedNumberOfOffsets = 0;
if (GetNumberOfOffsets(modifiedLogoBin) != numberOfOffsets){
fprintf(stderr, "ERROR: The number of offsets doesn't match the Original file!!\n");
fclose(modifiedLogoBin);
if (!badAss){
unlink("modified.logo.bin");
}
exit(0);
}
fprintf(stdout, "\n\nContents of the NEW \"modified.logo.bin\":\n");
fprintf(stdout, "VVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVV\n\n");
ListFileDetails(modifiedLogoBin, imageHeaders);
fprintf(stdout, "\n\n_____________________________________________________________\nOriginal filesize: ");
PrintFileSize(GetFileSize(originalLogoBin));
fprintf(stdout, "Modified filesize: ");
PrintFileSize(GetFileSize(modifiedLogoBin));
fprintf(stdout, "-------------------------------------------------------------\n");
fclose(originalLogoBin);
fclose(modifiedLogoBin);
return 1;
}
if (decodeAllOpt){
DecodeLogoBin(originalLogoBin, imageHeaders);
fclose(originalLogoBin);
return 1;
}
fclose(originalLogoBin);
return 1;
}
Interesting Can you tell me where do I find the logo.bin in my boot.img. I've extracted mine and don't see any sign of logo.bin. I own a OnePlus 2
shreyas.kukde said:
Interesting Can you tell me where do I find the logo.bin in my boot.img. I've extracted mine and don't see any sign of logo.bin. I own a OnePlus 2
Click to expand...
Click to collapse
Did you download a system image? If so, unzip it, and look for the folder "firmware-update". The logo.bin should be in there.
Works well for me! Thanks!
Grarak said:
Works well for me! Thanks!
Click to expand...
Click to collapse
Thanks!! Removed this:
This is untested on the oneplus 2, however I've looked at the logo.bin from your firmware and it is identical to the newer oneplus one logo.bin. Let me know! Thanks!
Grarak said:
Works well for me! Thanks!
Click to expand...
Click to collapse
how did you flash your modified logo.bin? if done through "fastboot flash logo logo.bin" it just quits with this error:
Code:
target reported max download size of 536870912 bytes
sending 'logo' (1581 KB)...
OKAY [ 0.064s]
writing 'logo'...
FAILED (remote: partition table doesn't exist)
finished. total time: 0.085s
this also happens with an unmodified logo.bin
markus1540 said:
how did you flash your modified logo.bin? if done through "fastboot flash logo logo.bin" it just quits with this error:
Code:
target reported max download size of 536870912 bytes
sending 'logo' (1581 KB)...
OKAY [ 0.064s]
writing 'logo'...
FAILED (remote: partition table doesn't exist)
finished. total time: 0.085s
this also happens with an unmodified logo.bin
Click to expand...
Click to collapse
You have to flash "LOGO" partition and not "logo"
makers_mark said:
You have to flash "LOGO" partition and not "logo"
Click to expand...
Click to collapse
gotta love case sensitivity. thanks, it worked.
awesome mod
It worked, thanks
This will work with Stock Oneplus 2 rom too, right?
Edit:
Working fine with my Onelus2 too, just got logo.bin from my stock Oxygen rom. Thanks again.
From where can I extract my logo.bin from my phone? I dont have the stock rom with me. I need this from 1+2 if this works with it?
Sent from my "GT-I9300/1+1" powered by Carbon Rom & Boeffla/ak Kernel
Fueled by 7000mAh ZeroLemon Battery
Edit:
Working fine with my Onelus2 too, just got logo.bin from my stock Oxygen rom. Thanks again.
shreyas.kukde said:
Interesting Can you tell me where do I find the logo.bin in my boot.img. I've extracted mine and don't see any sign of logo.bin. I own a OnePlus 2
Click to expand...
Click to collapse
nicesoni_ash said:
From where can I extract my logo.bin from my phone? I dont have the stock rom with me. I need this from 1+2 if this works with it?
Click to expand...
Click to collapse
I went into changing the splash screen only after I'd already changed to custom rom ( bliss 6 ), so I didn't had any official OPT rom zip.
I tried to use the "logo.bin.p" from latest OTA updates FROM HERE... but the LogoInjector telling me that "This is NOT a valid Logo.bin".
Solution I found -> I managed to EXTRACT THE LOGO.BIN FILE FROM THE OPT ITSELF !!!
I got it right after I read about this command and saw the "updater-script" from one of the official OTA updates that included a hint about logo.bin place in the OPT internal storage :
apply_patch("EMMC:/dev/block/bootdevice/by-name/LOGO:305152:567b5d4deed7f4875809ae8b7f071ab38e5a94d5:305152:16c76f9c0cadf8be18eed0961dfbcf3b7bd0aacf",
"-", 16c76f9c0cadf8be18eed0961dfbcf3b7bd0aacf, 305152,
567b5d4deed7f4875809ae8b7f071ab38e5a94d5, package_extract_file("patch/firmware-update/logo.bin.p"));
Click to expand...
Click to collapse
so... how to extract to logo.bin ?
Note: If you don't know what you're doing - DO NOT DO IT ! DD command is DANGEROUS !
Using adb open shell and run the following command:
dd if=/dev/block/bootdevice/by-name/LOGO of=/sdcard/logo.bin bs=305152 count=1
Click to expand...
Click to collapse
This will create a "logo.bin" file inside the root of your internal memory aka /sdcard folder.
I got from that the following image files list:
Resolution - Offset - Name
1080x1920 | 0............ | fhd_oppo_1080_1920_result.raw ---> THE SPLASH IMAGE !!!
536x60.........| 65536 | fhd_at_536_60_result.raw
300x1020....| 75264 | fhd_charger_300_1020_result.raw
1080x1920 | 89600 | fhd_fastboot_1080_1920_result.raw ---> THE FASTBOOT IMAGE !!!
1080x1920 | 145920 | fhd_lowpower_1080_1920_result.raw
392x66 ........| 277504 | fhd_rf_392_66_result.raw
487x69 ........| 285184 | fhd_wlan_487_69_result.raw
Note, inorder to load the png to the logo.bin you need to rename the png you make as *.raw according to this list above.
Now... inorder to "flash" the logo.bin back to the OPT I use the attached zip.
you only need to add "logo.bin" to the root of this zip, then flash it through TWRP.
@makers_mark - once again, after your OPO development - Thanks A LOT for developing & sharing with us LogoInjector for the OPT as well
@makers_mark
Could you make one for oneplus3?
Thanks in advance.
logo.bin for oneplus3 is attached.