Related
I have a rooted (Superuser 3.1.3) TF101 with TWRP 2.7.0.1. I HAD Katkiss 4.3 installed. One day the tablet locked up and then starting bootlooping. I went into recovery, wiped everything, did factory reset, format /system.
Then I tried to reflash Katkiss 4.3_020, it failed with "set_perm: some changes failed". I then tried katkiss 4.4.2_023c - it failed with a similar error message. Tried flashing stock (US_epad-user-9.2.1.27) - same thing. The first part of the error message for all three ROMs is the same set_perm failure. The next couple of lines gives different error messages depending on the ROM. Generally something like: "E: error executing updater binary in zip".
Now I have a tablet with no ROM on it (when I tried to boot it hangs at the ASUS screen). I can get into the TWRP recovery menu just fine - I can flash other things like superuser or gapps without error. But any ROM I try to flash gives the set_perm error.
Any thoughts?
Chris
Try using Easyflasher to flash a different version of TWRP in case recovery is the problem, TWRP builds newer than 2.3.2.3 are not official builds, they have been continued by another member here once the project was abandoned by the original team
http://forum.xda-developers.com/showthread.php?t=1688012
Use Easyflasher to flash TWRP again - then try flashing KatKiss #23
Thanks but...
Easyflasher doesn't seem to work for me anymore (odd because it is what I first used to root/update my TF101). It runs and declares success - but nothing gets pushed to my device. Tried both SBK1 and SBK2. Using universal naked 0.72 and 0.73 on win7 64 bit.
I tried to find an older version of TWRP like you suggested - but I couldn't. Seems they want you to use "goo manager" from the play store... which doesn't work for me since I can't boot... And the goo website doesn't list an older TWRP for my device.
In any case, the latest TWRP seems to work in every other respect. I read somewhere that superuser can set an "immutable" bit that can survive a wipe? If true - could that be my permissions problem?
Chris
stuck on load screen
*Detection* said:
Try using Easyflasher to flash a different version of TWRP in case recovery is the problem, TWRP builds newer than 2.3.2.3 are not official builds, they have been continued by another member here once the project was abandoned by the original team
http://forum.xda-developers.com/showthread.php?t=1688012
Use Easyflasher to flash TWRP again - then try flashing KatKiss #23
Click to expand...
Click to collapse
I'm new as one can get at this and likely deserve any hammering I may get....TF1010 B70, CWM 5.8.3.4, I know I missed a step somewhere. I can't recover to 4.3 as the back up was bad, not recognized by any computer, loops to recovery and holding power and vol dn the booting to the linuz get me a long (14 hrs) flashing KatKiss boot screen.
I've tried Easyflasher aswell with no results, Please, any hope for this thing, Thanks in advance!
Sounds like your problem is a bit different - can you get into your bootloader? After voldown+power you should see some small text in the upper left of the screen then immediately hit vol up.... From there you should be able to reflash any ROM...
ldwhyte said:
I'm new as one can get at this and likely deserve any hammering I may get....TF1010 B70, CWM 5.8.3.4, I know I missed a step somewhere. I can't recover to 4.3 as the back up was bad, not recognized by any computer, loops to recovery and holding power and vol dn the booting to the linuz get me a long (14 hrs) flashing KatKiss boot screen.
I've tried Easyflasher aswell with no results, Please, any hope for this thing, Thanks in advance!
Click to expand...
Click to collapse
ChrisG12 said:
Sounds like your problem is a bit different - can you get into your bootloader? After voldown+power you should see some small text in the upper left of the screen then immediately hit vol up.... From there you should be able to reflash any ROM...
Click to expand...
Click to collapse
Thanks for your reply, when I do use that button combo, it goes into the ClockworkMod Recovery v5.8.3.4, the native one seems to be gone.
Is that a bad thing? Once in ClockworkMod - you can install a new ROM (such as KatKiss or even go back to stock). Just find the right zip file on the web, copy to your sdcard and then in clockwork select that zip file to install.... Or am I missing something?
ldwhyte said:
Thanks for your reply, when I do use that button combo, it goes into the ClockworkMod Recovery v5.8.3.4, the native one seems to be gone.
Click to expand...
Click to collapse
Ok - back to my problem - I installed a new recovery and get the same error. The two recoveries I have tried are TWRP (2.3 and 2.7.0.1) and cwm-6.0.2.1-notouch-hybrid. Both seem to work fine (and I had no trouble previously with my device running TWRP and Katkiss 4.3).
After a crash I needed to reinstall a ROM. I've copied four ROMs to my sdcard (Katkiss 4.3, Katkiss 4.4.2, Omni 4.4.2, and stock asus). I've tried all 4 ROMs with both recoveries. I get the same error when I try to install the zips. Usually it is "set_perm: some changes failed". Though stock asus zip fails with a different message "Assert failed: package_extract_file(“blob”, “/tmp/blob”)".
Any ideas on what is keeping a recovery from installing the zip? Note they can install other zips fine (i.e. other recoveries, superuser, gapps, etc.). But not the ROM.
ChrisG12 said:
Is that a bad thing? Once in ClockworkMod - you can install a new ROM (such as KatKiss or even go back to stock). Just find the right zip file on the web, copy to your sdcard and then in clockwork select that zip file to install.... Or am I missing something?
Click to expand...
Click to collapse
No it's not, but I can't get anything onto the SD card, only the ext card and I CWM will not mount it to flash from. if I'm missing something and I sure I am, Im greatful for any help, and thanks again..
Can anyone tell me how I flash a recovery to the device from a zip file? Going into CWM and flashing the TWRP recovery initially seems to work, but if I then interrupt the reboot and go straight into recovery, I still see CWM, not TWRP. I'm stuck on the CWM recovery and need TWRP to try to install the Kitkat upgrade.
Should I unzip the components first and then flash the image using fastboot, or is there another way? I'm wary of fastboot as I've already (temporarily) "bricked" the Xoom by flashing a zip instead of an image that way. None of the instructions I've read has much advice on getting round installation problems.
I'm guessing the persistent CWM was caused by my selecting (at an earlier stage) the CWM option to fix the problem of the stock recovery being reinstated at each reboot. Can this be undone? Although I've installed Xoom-Universal-Root, apps that require root access - including GooManager - also fail with an access error. It's hard to tell whether the device is now rooted or not, so if there's any method of getting further without root access, that would be great.
====================
Edit: it looks as if the instructions I saw online, which mentioned two separate TWRP recoveries, were incorrect. To get Android Kitkat 4.4 onto my Xoom I didn't need the initial TWRP recovery, only the BigPart version. Once I skipped to the BigPart recovery, the problem described above did not recur.
Hello,
My TF700 was on a CleanRom (2.3 i think), for a while, i decided to update.
- I installed the latest CWM (via fastboot) and flashed a Cyanogen 10.2 "stable", but my tablet freezed very quickly after successful boot, i tried some reboots and get same problem.
- I tried to install a stock ODEX root ROM, the tablet freezed at asus logo
- I flashed TWRP instead of CWM, it doesn't helped
- I tried wipe data and cache with TWRP, then my data was not accessible anymore and TWRP was unable to re-create it
- I searched on forums and found on this one that flash a boot.blob file can solve the problem
- It doesn't and now CWM and TWRP refuse to work ....
So i post here before getting my tablet completely brick.
At this point, i get access to fastboot / abd, CWM load but don't work (reboot when trying to do something), TWRP don't load.
Any suggestion to get back to a Stock ODEX rooted rom ?
Excuse my english ...
Asphodele said:
Hello,
My TF700 was on a CleanRom (2.3 i think), for a while, i decided to update.
- I installed the latest CWM (via fastboot) and flashed a Cyanogen 10.2 "stable", but my tablet freezed very quickly after successful boot, i tried some reboots and get same problem.
- I tried to install a stock ODEX root ROM, the tablet freezed at asus logo
- I flashed TWRP instead of CWM, it doesn't helped
- I tried wipe data and cache with TWRP, then my data was not accessible anymore and TWRP was unable to re-create it
- I searched on forums and found on this one that flash a boot.blob file can solve the problem
- It doesn't and now CWM and TWRP refuse to work ....
So i post here before getting my tablet completely brick.
At this point, i get access to fastboot / abd, CWM load but don't work (reboot when trying to do something), TWRP don't load.
Any suggestion to get back to a Stock ODEX rooted rom ?
Excuse my english ...
Click to expand...
Click to collapse
Hey Your in the right place
Shoot me an email, we can review your issues and if we find a solution we can post back here to help
XDA users with there issues....
My email is everywhere talke a look around
Thx Josh
Asphodele said:
Hello,
My TF700 was on a CleanRom (2.3 i think), for a while, i decided to update.
- I installed the latest CWM (via fastboot) and flashed a Cyanogen 10.2 "stable", but my tablet freezed very quickly after successful boot, i tried some reboots and get same problem.
- I tried to install a stock ODEX root ROM, the tablet freezed at asus logo
- I flashed TWRP instead of CWM, it doesn't helped
- I tried wipe data and cache with TWRP, then my data was not accessible anymore and TWRP was unable to re-create it
- I searched on forums and found on this one that flash a boot.blob file can solve the problem
- It doesn't and now CWM and TWRP refuse to work ....
So i post here before getting my tablet completely brick.
At this point, i get access to fastboot / abd, CWM load but don't work (reboot when trying to do something), TWRP don't load.
Any suggestion to get back to a Stock ODEX rooted rom ?
Excuse my english ...
Click to expand...
Click to collapse
Sounds like you are on an old bootloader. Flash the stock rom from asus by unzipping the zip you download from their website and placing in the root folder of your micro sd and then go into rck from the bootloader menu (power + volume down whilst booting)
Or you could just flash it from recovery....
lj50036 helped me to flash a new bootloader, recovery, rom and nvflash to make it unbrickable
Not just helped he spent many times to explain me how it works and what he did.
He is very nice and this was a pleasure to talk with him, i'm happy that there's still person like that on this planet
see you !
Asphodele said:
lj50036 helped me to flash a new bootloader, recovery, rom and nvflash to make it unbrickable
Not just helped he spent many times to explain me how it works and what he did.
He is very nice and this was a pleasure to talk with him, i'm happy that there's still person like that on this planet
see you !
Click to expand...
Click to collapse
I buy a tf700 with cm 11 a few days ago i am really interessted on how this steps works. I really want to make it unbrickeable, But i dont really understand how it works. I can not enter in fastboot. at least i got cwm interface when rebooting with adb into recovery.
Can u explain how you did it?
It invovles flashing a modified bootloader and the flatline recovery and then using Wheelie to generate your nvflash blobs.
Step-by-step instructions (which you need to follow to the letter) are here:
https://www.androidroot.mobi/pages/guides/tegra3-guide-nvflash-jellybean/
Stuck in boot loop, fastboot and recovery accessible
Hello,
I'm having a similar issue and I need help! Initially my tablet was rooted with Cromi-X 5.4. Then I decided to try Crombi-KK.
Here is what happened:
- Updated TWRP recovery
- Did a full wipe as recommended
- Flashing got stuck at the Crombi-KK loading sign
- Tried to reflash but TWRP wasn't detecting data partition anymore
- Instead installed the other recommended recovery CWMR.
- Flashed Crombi-KK, it worked. Played around with it for a few days, it was wonderful, fast and responsive.
- Battery died out and when I turned it back on I got a UIDs system inconsistent error.
- I found online many recommendations to reflash so I tried to do that
- Since then I'm stuck in a boot loop. I see the initial "bios" Asus logo then it restarts over and over.
- I am able to access bootloader and recovery
I've tried reflashing the asus stock blob. I've tried wiping the data through CWMR but it starts working and then it restarts. I don't know what to do anymore, so if anyone can help me, I would really appreciate it!
Thanks
Which recovery and bootloader version do you have now?
A (for KK) outdated bootloader seems the most likely culprit.
You can try save the recovery log when you flash or grab a logcat of the bootloop, but probably it'll only tell you that the recovery cannot mount /data.
Determine that you are on the correct bootloader, if not update it. If you're lucky the tablet will start right up. If it doesn't, formatting /data is the only way I know to get it back. Not just wiping - formatting it. You will loose everything on internal SD, so I hope you have a nandroid you can restore from later.
If you use TWRP 2.7+ be aware that formatting can take more than an hour. Let it finish!
For good measure, download CROMBi-KK again, check the md5 and then flash that file.
I'm on 10.6.1.14.10 bootloader which I think is the latest one
I have 6.0.4.7 CWMR
I'm trying to format data completely but when i do it in CWMR it starts and then the tablet reboots on it's own after a couple of minutes.
How can I retrieve the logs, I never had to do it before.
Thanks for your help
Mhh, getting a little more complicated.
Your BL is ok...
What do you see in CWM when you go into Mounts and Storage? What is mounted?
The recovery logs are under Advanced > show logs.
I'm at work now but from what I remember the only thing mounted was the cache. I'll double check tonight. Do you think there's any hope or I have a brand new paper weight?
yasyas said:
I'm at work now but from what I remember the only thing mounted was the cache. I'll double check tonight. Do you think there's any hope or I have a brand new paper weight?
Click to expand...
Click to collapse
Can you fastboot flash twrp?
It's much much better than CWM, has its own terminal and will be easier to offer the correct format command.
sbdags said:
Can you fastboot flash twrp?
It's much much better than CWM, has its own terminal and will be easier to offer the correct format command.
Click to expand...
Click to collapse
So I flashed TWRP and when I go in mount/storage everything is selected except for system. Should I do a format data from the wipe menu before flashing crombi-kk again?
yasyas said:
So I flashed TWRP and when I go in mount/storage everything is selected except for system. Should I do a format data from the wipe menu before flashing crombi-kk again?
Click to expand...
Click to collapse
To be in the safe side, yes, that is what I would do. TWTRP 2.7.+ takes a long time to format and it may seem the process got stuck. Give it at least 90 minutes to finish.
Then reflash CROMBi
I'm back up and running !!!
This time installing TWRP, everything was mounted (maybe my previous flash before CWMR wasn't good), did a format data, waited until it was done, flashed latest Crombi-KK and going through setup now. Hopefully won't have the same UID issue on next shutdown. I didn't enable fsync or journaling so hopefully it won't happen again.
Thanks both of you for your help!
Good deal! Happy for you!
Rooting google pixel zl
I have a Moto G X1032 rooted with TWRP installed. I've been using the stock firmware for 4.4.2 without any issues for a while, but after June 6th's OTA update to 4.4.3, my phone has gotten stuck in a boot loop. It turns on and runs Android as usual, without any issues, for less than a minute and then shuts down. It then continues to boot back up and continue the process. The only way to stop the loop is to boot into the bootloader from TWRP and power off the phone from there. Luckily I have a backup to that reverts me back to 4.4.2, which successfully stops the loop. But after several attempts to update to 4.4.3, it has become quite clear that this boot loop is inevitable unless I stick with 4.4.2. I read an article that seems to address some conflict with rooted phones and 4.4.3, but I'm not quite sure what the conflict is. Can anyone explain to me why this boot loop is most likely happening, what I could do to fix it, or if it is even possible to have a rooted X1032 with 4.4.3 installed? Any help whatsoever would be greatly appreciated. Thank you.
Are you saying you tried to install the OTA with TWRP installed and not the stock recovery?
Just go into recovery clear all cache,kavik cache that should do
NerdNoob1210 said:
I have a Moto G X1032 rooted with TWRP installed. I've been using the stock firmware for 4.4.2 without any issues for a while, but after June 6th's OTA update to 4.4.3, my phone has gotten stuck in a boot loop. It turns on and runs Android as usual, without any issues, for less than a minute and then shuts down. It then continues to boot back up and continue the process. The only way to stop the loop is to boot into the bootloader from TWRP and power off the phone from there. Luckily I have a backup to that reverts me back to 4.4.2, which successfully stops the loop. But after several attempts to update to 4.4.3, it has become quite clear that this boot loop is inevitable unless I stick with 4.4.2. I read an article that seems to address some conflict with rooted phones and 4.4.3, but I'm not quite sure what the conflict is. Can anyone explain to me why this boot loop is most likely happening, what I could do to fix it, or if it is even possible to have a rooted X1032 with 4.4.3 installed? Any help whatsoever would be greatly appreciated. Thank you.
Click to expand...
Click to collapse
The bootloop is caused by the recovery. It can't update 4.4.3 and keeps trying. Start the update again and let the OTA file download, then copy it out of /cache and into the sdcard. If it's not in cache it won't bootloop. I suggest flashing PhilZ recovery and updating with that instead. Flash the file in the sdcard and post whatever errors are listed...
secretkloud said:
The bootloop is caused by the recovery. It can't update 4.4.3 and keeps trying. Start the update again and let the OTA file download, then copy it out of /cache and into the sdcard. If it's not in cache it won't bootloop. I suggest flashing PhilZ recovery and updating with that instead. Flash the file in the sdcard and post whatever errors are listed...
Click to expand...
Click to collapse
Thank you. I will try that. Before I do though, do you know of any places I could find 4.4.3 online, so I could just download it from my PC and flash it over via sideload? I usually prefer to flash things that way, rather than straight from the phone.
bozzykid said:
Are you saying you tried to install the OTA with TWRP installed and not the stock recovery?
Click to expand...
Click to collapse
Yes. This is my first time doing so, excuse my lack of knowledge on the subject. In retrospect, I suppose I should have known there must be a different method with which I install it. Secretkloud gave me a good suggestion though. Is there a reason in particular as to why I can't do OTA updates with custom recovery installed?
secretkloud said:
The bootloop is caused by the recovery. It can't update 4.4.3 and keeps trying. Start the update again and let the OTA file download, then copy it out of /cache and into the sdcard. If it's not in cache it won't bootloop. I suggest flashing PhilZ recovery and updating with that instead. Flash the file in the sdcard and post whatever errors are listed...
Click to expand...
Click to collapse
I just downloaded the zip from my phone and flashed it from Phillz recovery. It worked very well and the update was successful. Thanks for pointing me to Phillz recovery by the way. It's the only functional recovery image that allows me to mount the sdcard.
NerdNoob1210 said:
Thank you. I will try that. Before I do though, do you know of any places I could find 4.4.3 online, so I could just download it from my PC and flash it over via sideload? I usually prefer to flash things that way, rather than straight from the phone.
Click to expand...
Click to collapse
Copy the one you have in your phone onto your PC. Smallest chance of error if you do it that way...
it's not easy getting out of the loop.
I did a factory reload of a rooted phone with CWM.
Now for the CWM issue the Moto G loaded OK and then said there was an update for android to fix some bugs. This was 4.4.3. I loaded it and it gets half way and it then says
"Signature verification fail"
at the bottom of the screen and
" Install Untrusted Package"
The options are yes, no or go back
at the top....
whichever one I try it then tries to boot shows the Android / Motorola screen and starts up gets a txt message for 2-3 seconds... it then goes back to Android CWM recovery with the same options as above and repeats the process. again and again and again. No function keys will stop this cycle which just repeats again. This continues until the battery dies.
any ideas ? how can I override this action in CWM v6.0.4.6 and force it to do a factory reload ? any help or advice much appreciated.
If you can still power your phone, can you still access the boot loader? If so, I would suggest using adb from a computer to flash Phillz recovery. CWM always gave me a lot of random errors when flashing items. You could use PhillZ to flash the stock ROM for 4.4.2. After that, just follow the same process I did. Download the update zip via the OTA download when it prompts you. Once it's finished, DON'T boot back into Android. Boot into Phillz recovery from the boot loader, move the zip out of the cache and onto sdcard or your computer, and then flash it either straight from the phone or by sideloading it from your computer. Then you'll have a working version of vanilla 4.4.3, and you can flash over a custom ROM in the future if you so choose.
Sent from my XT1032 using XDA Premium 4 mobile app
NerdNoob1210 said:
If you can still power your phone, can you still access the boot loader? If so, I would suggest using adb from a computer to flash Phillz recovery. CWM always gave me a lot of random errors when flashing items. You could use PhillZ to flash the stock ROM for 4.4.2. After that, just follow the same process I did. Download the update zip via the OTA download when it prompts you. Once it's finished, DON'T boot back into Android. Boot into Phillz recovery from the boot loader, move the zip out of the cache and onto sdcard or your computer, and then flash it either straight from the phone or by sideloading it from your computer. Then you'll have a working version of vanilla 4.4.3, and you can flash over a custom ROM in the future if you so choose.
Sent from my XT1032 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
unfortunately I can't get into bootloader. I can connect usb and it makes no difference. therefore adb commands dont work. it just goes straight into screen described with those three options. I'm hoping that there is an override action in CWM which isn't power and volume down which do nothing.
thanks for the suggestion tho. it was a good idea.
Hm... Without access to the boot loader, I'm not sure there's much of anything you can do anymore... You've completely lost the ability to communicate any sort of commands to your phone save for the 3 options that menu provides. I assume that what CWM is trying to do is install the zip from your cache and is failing to do so. The only viable option would be to flash a new recovery image and install the zip manually, but that's impossible for you given your current circumstances. I would give up looking for an override command for CWM, your best hope is to find an alternative means with which you can access your boot loader. I suggest you start a thread dedicated to your issue and see if a more experienced user can provide you with the information you need. Sorry, I hope you get the help you need. :/
Sent from my XT1032 using XDA Premium 4 mobile app
Thanks for trying to help. I have followed your advice and opened a thread
NerdNoob1210 said:
Hm... Without access to the boot loader, I'm not sure there's much of anything you can do anymore... You've completely lost the ability to communicate any sort of commands to your phone save for the 3 options that menu provides. I assume that what CWM is trying to do is install the zip from your cache and is failing to do so. The only viable option would be to flash a new recovery image and install the zip manually, but that's impossible for you given your current circumstances. I would give up looking for an override command for CWM, your best hope is to find an alternative means with which you can access your boot loader. I suggest you start a thread dedicated to your issue and see if a more experienced user can provide you with the information you need. Sorry, I hope you get the help you need. :/
Sent from my XT1032 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Hi,
Just for you to know:
Model: r7plusf
Recovery: TWRP 3.0.2-0
----------------------------------------
So earlier today I did an OTA update (cm-14.1-20161205-NIGHTLY-r7plus.zip), but couldn't get my phone to boot.
So naturally, I tried wiping Cache and ART cache, but was still bootlooping.
Thought there might be someting wrong with my ROM and data, so I formated data and Installed ROM and GAPPS again after ADB pushing them onto my phone.
Now, and although CM14.1 and GAPPS are successfully installed on my Oppo R7 Plus, I can't boot into the OS. Every time I try reboot system, whether through POWER_BUTTON, RECOVERY or ADB, I just boot into Recovery.
Worst of all, for some unknown reason, I can't get into BOOTLOADER, neither through button combination, nor through Recovery nor ADB.
I found this article (http://forum.xda-developers.com/tmobile-lg-g3/general/fix-recovery-loop-twrp-computer-t2873386) in the LG G3 thread about executing some shell commands, but I haven't tested testing it with my phone's variables because it might hard brick it...
Please Help!
[EDIT] I now have access to fastboot but still recovery looping like crazy.
I installed the same update via CyanDelta , worked like a charm ! hopefully you get back up and running.
[UPDATE] strangely I tried to flash stock recovery and boot CM13 and it worked!
Will try to flash twrp again and insall CM14
keep you up to date
Same thing happened to me! Where did you get a copy of the stock recovery? Link?
resverse said:
[UPDATE] strangely I tried to flash stock recovery and boot CM13 and it worked!
Will try to flash twrp again and insall CM14
keep you up to date
Click to expand...
Click to collapse
I had the same problem. Can't remember exactly how I resolved it. But I think, I use CM recovery to flash nightly. Then flash TWRP to flash gapps. For some strange reason, using CM recovery also show no enough disk space whenever I try to flash opengapps. But TWRP recovery can flash opengapps successfully.
Don't use the OTA, use adb sideload to flash the nightly next time. So far, adb sideload has not given me any issue to flash nightly.
Same problem...
I tried a lot of things nothing works and now I've installed the cm recovery but I have the "unauthorized phone" in terminal when I try to flash the ROM... I can do nothing because I can't enable the usb debugging. I don't know what to do.
If somebody can help I appreciate.
corbalan12 said:
Same problem...
I tried a lot of things nothing works and now I've installed the cm recovery but I have the "unauthorized phone" in terminal when I try to flash the ROM... I can do nothing because I can't enable the usb debugging. I don't know what to do.
If somebody can help I appreciate.
Click to expand...
Click to collapse
Since then I found how to fix it :
first of all I flashed cm13 through TWRP,
Then I flashed the stock recovery (Google it, I found it in OPPO forums) with fastboot,
After that I did a factory reset in the stock recovery,
Booted cm13 with stock recovery,
Then re-flashed TWRP,
From TWRP, I wiped both data and system partitions,
Then fresh installed cm14 and Gapps
And it worked!
Not sure if those are the exact steps I followed because all I did was a hole lot of messing around and trying absurd things out, but think this is how I fixed it.
Let me know if it worked for you or if you still can't fix your problem
Best of luck
Resverse
resverse said:
Since then I found how to fix it :
first of all I flashed cm13 through TWRP,
Then I flashed the stock recovery (Google it, I found it in OPPO forums) with fastboot,
After that I did a factory reset in the stock recovery,
Booted cm13 with stock recovery,
Then re-flashed TWRP,
From TWRP, I wiped both data and system partitions,
Then fresh installed cm14 and Gapps
And it worked!
Not sure if those are the exact steps I followed because all I did was a hole lot of messing around and trying absurd things out, but think this is how I fixed it.
Let me know if it worked for you or if you still can't fix your problem
Best of luck
Resverse
Click to expand...
Click to collapse
Thank you very much!!!! I'll try tomorrow and tell you.
I appreciate a lot!
First of all now works but to be honest, I don't know if the way I fix makes sense or if is correct but not for the same reason I do but I'll try to explain...
I had cm-14.1-20161218-NIGHTLY and I tried to update via OTA to 20161220 the phone reboot and I get the bootloop. The first I thought, install again the ROM making wipe data and blabla... nothing work.
I tried to "reflash" the recovery, nothing. Flashed cm recovery, it always gave me error trying to flash the rom. I tried to install with stock recovery, errors too.
I was reading hundred of post looking for my issues, device unauthorized, "error 7" in twrp... I was crazy.
At last I thought, I've been trying to install from SDcard, if I try to install from internal memory? and I install again the twrp to transfer the ROM and Gapps to the internal memory and... it worked!!!!
Long story but with happy ending.
Thank you for your help I appreciate and sorry for my english.First of all now works but to be honest, I don't know if the way I fix makes sense or if is correct but not for the same reason I do but I'll try to explain...
I had cm-14.1-20161218-NIGHTLY and I tried to update via OTA to 20161220 the phone reboot and I get the bootloop. The first I thought, install again the ROM making wipe data and blabla... nothing work.
I tried to "reflash" the recovery, nothing. Flashed cm recovery, it always gave me error trying to flash the rom. I tried to install with stock recovery, errors too.
I was reading hundred of post looking for my issues, device unauthorized, "error 7" in twrp... I was crazy.
At last I thought, I've been trying to install from SDcard, if I try to install from internal memory? and I install again the twrp to transfer the ROM and Gapps to the internal memory and... it worked!!!!
Long story but with happy ending.
Thank you for your help I appreciate and sorry for my english.