Database Info

help- bricked it, no recovery, what now?

Hey yall. I had the phone for 6 days before I bricked it. I am wondering if there is any stock recovery mode or anything or what I shsould do? I think something went wrong due to using the root toolbox pro app. I have done some backups within the ap as well as Titanium Backup but now the phone will not boot up and I dont know if/how to put it in factory recovery mode. Soft reset does nothing. The Motorola logo will show on startup but then the screen just blacks out forever, not off, just colored black.
A few details, the phone was rooted with Motofail2go, with no recovery and bootloader still locked as far as I know.
Should I take it to Sprint for a factory reset? Is this even an option? What are my other options?
Next time I will probably use the Moto unlock key so I can open the bootloader all legit like and have a recovery mode...

Try holding power button and the down volume key to power off. Once you power off press and hold them again. This should boot you into fastboot, Motorola's adb shell basically. This can take a couple tries, make sure the phone is powered down completely before hitting volume down and power button to get into fastboot. If you can boot into fastboot you can unlock using this guide: http://www.droid-life.com/2012/08/20/how-to-unlock-the-motorola-photon-q-bootloader/
Once unlocked flash the custom recovery of your choice (I like twrp). You can boot into custom recovery by holding volume up and the power button from a powered down state. Here is the link for instructions on how to flash twrp:
http://forum.xda-developers.com/showthread.php?t=1887070
Then you can download one of the stock backups for the Q posted in the development section and restore them using the custom recovery. Most of the ones I have seen have been compatible with twrp.
The only way to download the stock rom backups is to remove the sd card from your phone, plug your sd card into a PC or other device with a card reader, download the stock backups, and place the stock backup rom files on your sd card. Finally place the sd card with the stock backup downloads into your phone.
These backups and information on how to go through this process can be found in this thread on page 2: http://forum.xda-developers.com/showthread.php?t=2001226
The key is to make a backup of your existing rom with twrp and then move the stock backups from your sd card to the twrp/backups/yourdeiceserial/ directory. That creates a backup directory which twrp knows to look for backups in.
Don't feel bad, I've been in that state several times since getting the Q, live and learn.
Sent from my XT897 using xda app-developers app

UnicronAlpha99 said:
Try holding power button and the down volume key to power off. Once you power off press and hold them again. This should boot you into fastboot, Motorola's adb shell basically. This can take a couple tries, make sure the phone is powered down completely before hitting volume down and power button to get into fastboot. If you can boot into fastboot you can unlock using this guide: http://www.droid-life.com/2012/08/20/how-to-unlock-the-motorola-photon-q-bootloader/
Once unlocked flash the custom recovery of your choice (I like twrp). You can boot into custom recovery by holding volume up and the power button from a powered down state. Here is the link for instructions on how to flash twrp:
http://forum.xda-developers.com/showthread.php?t=1887070
Then you can download one of the stock backups for the Q posted in the development section and restore them using the custom recovery. Most of the ones I have seen have been compatible with twrp.
Don't feel bad, I've been in that state several times since getting the Q, live and learn.
Sent from my XT897 using xda app-developers app
Click to expand...
Click to collapse
If that does not work you could drop it in water or something. You have not officially unlocked boot loader so you still have warranty. Or you could just tell sprint it quit working and act completely clueless. At least its bricked with warranty still intact.

matt2k12 said:
Hey yall. I had the phone for 6 days before I bricked it. I am wondering if there is any stock recovery mode or anything or what I shsould do? I think something went wrong due to using the root toolbox pro app. I have done some backups within the ap as well as Titanium Backup but now the phone will not boot up and I dont know if/how to put it in factory recovery mode. Soft reset does nothing. The Motorola logo will show on startup but then the screen just blacks out forever, not off, just colored black.
A few details, the phone was rooted with Motofail2go, with no recovery and bootloader still locked as far as I know.
Should I take it to Sprint for a factory reset? Is this even an option? What are my other options?
Next time I will probably use the Moto unlock key so I can open the bootloader all legit like and have a recovery mode...
Click to expand...
Click to collapse
Both of the methods above are very effective. When I had the first photon I bricked it and just dropped it in water and did a claim. Depending on the insurance you have that way may cost you $100. The other method should work. When I first got this phone I did the exact same thing and to go back and unlock then flash twrp and in stall a stock backup someone had posted.
Sent from my XT897 using Tapatalk 2

UnicronAlpha99 said:
Try holding power button and the down volume key to power off. Once you power off press and hold them again. This should boot you into fastboot, Motorola's adb shell basically. This can take a couple tries, make sure the phone is powered down completely before hitting volume down and power button to get into fastboot. If you can boot into fastboot you can unlock using this guide: http://www.droid-life.com/2012/08/20/how-to-unlock-the-motorola-photon-q-bootloader/
Click to expand...
Click to collapse
Thanks for the response. Is there anything extra extra special about getting into factory fastboot mode? I can't seem to get it done. Is there an official set of instructions anywhere? Does the phone need to be plugged into the PC? It was always my understanding (for the last week) that Power and Vol Down was the soft reset mode which reboots the phone. Therefore it always tries to reboot in normal mode. This is what keeps happening. It never powers completely down using this method.
Anyhow, once I follow your instructions, the Moto logo appears, no Sprint logo appears, the phone "powers on" but the screen is blacked out (not off). After waiting for a while at the blank/black screen, or holding down several buttons like vol or camera I get the first attachment: "Process system is not responding. Would you like to close it?" When I wait nothing happens. When I push OK nothing happens. By chance, I held down power during the notification and the power menu came up behind the ANR notice (second/third attachments). So obviously there are some things working but the main system isn't booting up. And either factory fastboot is nuked or I can't figure it out. When I power down from this accessible power menu and try to do the fastboot (Power / Vol Down) I still havent gotten it to work.
Any other ideas before I take drastic measures?
Since I bought it from Amazon would that be my best route for return or should I go thru a Sprint store?
Thanks in advance.

Hi again yall. You know once I got to thinking about it, I decided to check out the return policy on Amazon Wireless. They will accept any device under warranty for the first 30 days and it is up to Moto for the next 11 months of warranty coverage. They email me a packing label and it ships out 1 day and they ship out the new phone 1 day shipping. Hard to beat, just takes 2 days of shipping and some more fun times with my Epic, 10.1CM style, in the meantime.
Who's to say it wasnt some sort of hardware or software glitch that bricked the phone rather than my screwing around? Nobody knows and it isn't up to the consumer to prove his innocence. I bought everything legally, all the apps at the app store, and only ran the motofail2go root method. Wasn't running any custom Roms, Mods, or anything. I don't feel bad after they got me for another 2 grand for 24 months, and since I have been with Sprint for 10 years;l I have spent well over 10k or 15k with them lifetime.
If any other method pops up between now and when I ship it out I may give it a shot but if not, ah well, capitalism.

matt2k12 said:
Thanks for the response. Is there anything extra extra special about getting into factory fastboot mode? I can't seem to get it done. Is there an official set of instructions anywhere? Does the phone need to be plugged into the PC? It was always my understanding (for the last week) that Power and Vol Down was the soft reset mode which reboots the phone. Therefore it always tries to reboot in normal mode. This is what keeps happening. It never powers completely down using this method.
Anyhow, once I follow your instructions, the Moto logo appears, no Sprint logo appears, the phone "powers on" but the screen is blacked out (not off). After waiting for a while at the blank/black screen, or holding down several buttons like vol or camera I get the first attachment: "Process system is not responding. Would you like to close it?" When I wait nothing happens. When I push OK nothing happens. By chance, I held down power during the notification and the power menu came up behind the ANR notice (second/third attachments). So obviously there are some things working but the main system isn't booting up. And either factory fastboot is nuked or I can't figure it out. When I power down from this accessible power menu and try to do the fastboot (Power / Vol Down) I still havent gotten it to work.
Any other ideas before I take drastic measures?
Since I bought it from Amazon would that be my best route for return or should I go thru a Sprint store?
Thanks in advance.
Click to expand...
Click to collapse
Try using adb. If your computer has drivers on it for phone you might able to get into fast boot. If that does not work I would try Sprint store first. Have locked my phone up several times while hacking wife off in progress and have used adb every time. Only time i have been truely scared is when i soft bricked my nexus 7. had to stay at work for two hours after i got off to get it to recover because i was scared of her lol.
---------- Post added at 02:05 PM ---------- Previous post was at 01:57 PM ----------
If you get adb to recognize device you could take chance and officially unlock boot loader. Then flash twrp. There is a thread in general section about having trouble getting official update. It has a stock recovery in it. Trick would be moving files to recovery section of twrp

I have gotten the phone to soft power down and get into fast boot and custom recovery. It's a bit tricky with timing, I usually wait for the screen to go black after soft reset, let go, and immediately hold power and volume down. If you can not boot into fastboot I honestly don't know what you can do either than return the phone.
Sent from my XT897 using xda app-developers app

UnicronAlpha99 said:
I have gotten the phone to soft power down and get into fast boot and custom recovery. It's a bit tricky with timing, I usually wait for the screen to go black after soft reset, let go, and immediately hold power and volume down. If you can not boot into fastboot I honestly don't know what you can do either than return the phone.
Sent from my XT897 using xda app-developers app
Click to expand...
Click to collapse
Thanks for the help Unicron. I think Brandons method might be my only alternative... but you know what? I already have the box packed up to ship back to Amazon! I am still a noob; I dunno if I could go the distance on this one. I have been updating my Android SDK files since I got the phone but I never got it to recognize boot up thru ADB fastboot. disclaimer* I havent tried it in a couple days since all teh SDK updates completed.
I dunno though I am a big time DIYer when possible. If it werent for the massive amount of tape I put on the box and packing label I would already be trying this method. I can't convince myself just yet. Amazon makes it too easy. I could have the *new* phone by Friday. Then I wouldn't be wasting my remaining work week trying to hack into my personal Christmas present in order to make it function...........................................
Edit - Yes I'm impatient. My job is too demanding and I am trying to set a good precedent for 2013. Wasting the first 3 work days on a phone is not how I intend to start off the year. There is probably a valuable lesson to be learned from this as far as hacking experience and to be honest with the responses here I think I could get it to boot up from PC in SDK/ADB mode and go from there. I just didnt know if that was possible until after I made the claim with Amazon. I still have an entire day today and tomorrow if I want to indulge myself. It doesnt matter if I mail the package today or Wednesday, I can still get it by Friday. I believe this thread is still valuable because we have patterns of repeating past failures and I may find use of it when I recieve my new phone and, darn it, it mysteriously bricks as well. in the same fashion.... the only thing I was really trying to do was get all my apps on my SD card... sad huh?
Edit 2 - Opened up the box, tried fastboot and adb, nothing. Off she goes.

I don't blame you, it sounds easier to exchange in your case any way. The main suggestion I have is if you are getting into any type of build.prop or operating system tweaks that have potential to lead to boot loops or cause the phone not to boot, then unlock the bootloader and install custom recovery.
The Moto-fail method seems limited to only be able to run apps that require root. For me this has no use as I want to be able to have complete control over all aspects of the Android OS. There is not a huge mod community for the Q as yet but I believe Cyanogen will be a reality as Interloper continues working on it. I came from an Epic with Cyanogen and soft-bricked it a minimum of 50 times. CWM was very forgiving on that phone, the Q is a lot more finicky and frustrating.
If you have insurance through the carrier then you are going to pay $150 for a refurb if something goes wrong and you hard brick the phone. If you unlock bootloader and install custom recovery then you have a fail-safe in the form of nandroid backups and restores. Then you can mod away with little fear.
Good luck on the new phone and I hope you don't give up after six days of modding with the Q!
Sent from my XT897 using xda app-developers app

matt2k12 said:
Thanks for the help Unicron. I think Brandons method might be my only alternative... but you know what? I already have the box packed up to ship back to Amazon! I am still a noob; I dunno if I could go the distance on this one. I have been updating my Android SDK files since I got the phone but I never got it to recognize boot up thru ADB fastboot. disclaimer* I havent tried it in a couple days since all teh SDK updates completed.
I dunno though I am a big time DIYer when possible. If it werent for the massive amount of tape I put on the box and packing label I would already be trying this method. I can't convince myself just yet. Amazon makes it too easy. I could have the *new* phone by Friday. Then I wouldn't be wasting my remaining work week trying to hack into my personal Christmas present in order to make it function...........................................
Edit - Yes I'm impatient. My job is too demanding and I am trying to set a good precedent for 2013. Wasting the first 3 work days on a phone is not how I intend to start off the year. There is probably a valuable lesson to be learned from this as far as hacking experience and to be honest with the responses here I think I could get it to boot up from PC in SDK/ADB mode and go from there. I just didnt know if that was possible until after I made the claim with Amazon. I still have an entire day today and tomorrow if I want to indulge myself. It doesnt matter if I mail the package today or Wednesday, I can still get it by Friday. I believe this thread is still valuable because we have patterns of repeating past failures and I may find use of it when I recieve my new phone and, darn it, it mysteriously bricks as well. in the same fashion.... the only thing I was really trying to do was get all my apps on my SD card... sad huh?
Edit 2 - Opened up the box, tried fastboot and adb, nothing. Off she goes.
Click to expand...
Click to collapse
FWIW, pressing vol down + power til it resets then pressing the camera button + power once the screen is black gets you to the Boot Mode Selection Menu, where you can start recovery, fastboot, BP tools (still not sure what that is entirely) and some others. Seems to be a fairly reliable/easy method for getting to both recovery and fastboot from any point.

befrosty8612 said:
FWIW, pressing vol down + power til it resets then pressing the camera button + power once the screen is black gets you to the Boot Mode Selection Menu, where you can start recovery, fastboot, BP tools (still not sure what that is entirely) and some others. Seems to be a fairly reliable/easy method for getting to both recovery and fastboot from any point.
Click to expand...
Click to collapse
Sure wish I would have known that ahead of time. Does this work without any recovery mode and with the bootloader still locked?

matt2k12 said:
Sure wish I would have known that ahead of time. Does this work without any recovery mode and with the bootloader still locked?
Click to expand...
Click to collapse
It does work without any recovery mode and I believe it still works without the bootloader being unlocked, I didn't know about this myself until after I had already unlocked it. Sorry I couldn't help out sooner.

befrosty8612 said:
It does work without any recovery mode and I believe it still works without the bootloader being unlocked, I didn't know about this myself until after I had already unlocked it. Sorry I couldn't help out sooner.
Click to expand...
Click to collapse
Awesome, I am wanting to do the backdoor root method again but, of course, may brick it. I dont think Amazon will keep sending me new ones.... but maybe!

befrosty8612 said:
FWIW, pressing vol down + power til it resets then pressing the camera button + power once the screen is black gets you to the Boot Mode Selection Menu, where you can start recovery, fastboot, BP tools (still not sure what that is entirely) and some others. Seems to be a fairly reliable/easy method for getting to both recovery and fastboot from any point.
Click to expand...
Click to collapse
For anyone concerned, I knew it would only be a matter of time until bricking my new device. This damn Root Toolbox Pro did it to me again, and on a simple, menial task. I am going to be working thru the motions on getting this to work.
Using the instructions quoted I did get stock recovery to work or at least flash on the screen for a split second. Seems like there is a timer on the recovery screen. I am having trouble with the fastboot prompt though on the PC. Do I do it in the "platform-tools" folder which contains fastboot or in the "tools" folder of the main SDK directory? I am really a noob, can you give me the cliff notes of how to get into ADB, fastboot, etc on the Photon Q in order to do a factory reset? I already have Android SDK installed and completely up to date so that is done. And Fastboot is installed. I'm just having trouble crossing the finish line here... I can get the fastboot page opened in the stock recovery but from there I'm lost. I dont know what to type into the command prompt, in what directory, or what.... Also when I open the command prompt in the SDK folder on the PC with fastboot in the directory and type "adb reboot bootloader" it says "device not found". Maybe (surely) that is the wrong prompt?
FWIW my phone is showing the dead android guy. I didnt do anything besides try and clear up my Play Store download list which required a reboot. The phone never started back up. I dont know how much damage was done or info was lost or whatever, but seeing as how I was rooted but still locked, I had no custom recovery. So no back ups. Is there anything to restore or am I looking at a full wipe and restore?

matt2k12 said:
For anyone concerned, I knew it would only be a matter of time until bricking my new device. This damn Root Toolbox Pro did it to me again, and on a simple, menial task. I am going to be working thru the motions on getting this to work.
Using the instructions quoted I did get stock recovery to work or at least flash on the screen for a split second. Seems like there is a timer on the recovery screen. I am having trouble with the fastboot prompt though on the PC. Do I do it in the "platform-tools" folder which contains fastboot or in the "tools" folder of the main SDK directory? I am really a noob, can you give me the cliff notes of how to get into ADB, fastboot, etc on the Photon Q in order to do a factory reset? I already have Android SDK installed and completely up to date so that is done. And Fastboot is installed. I'm just having trouble crossing the finish line here... I can get the fastboot page opened in the stock recovery but from there I'm lost. I dont know what to type into the command prompt, in what directory, or what.... Also when I open the command prompt in the SDK folder on the PC with fastboot in the directory and type "adb reboot bootloader" it says "device not found". Maybe (surely) that is the wrong prompt?
FWIW my phone is showing the dead android guy. I didnt do anything besides try and clear up my Play Store download list which required a reboot. The phone never started back up. I dont know how much damage was done or info was lost or whatever, but seeing as how I was rooted but still locked, I had no custom recovery. So no back ups. Is there anything to restore or am I looking at a full wipe and restore?
Click to expand...
Click to collapse
As abnormal as it seems, your situation seems pretty normal... at least from my shoes. I went through the same scenario... I didn't know what adb was, or fastboot, etc. So, here's what I know
the fastboot commands work even if adb doesnt see it in the list of devices attached. Somehow it just works (as long as the phone is in fastboot mode).
If you're able to get to the fastboot mode, things should be okay. Just open a windows explorer window to the Platform-Tools, hold the shift key and right click on a blank space within the window, then click open command window here.
you should be able to pass any adb (if the phone is on and recognized) or fastboot (if phone is in fastboot mode) commands from that command prompt.
Also, if you have a stock recovery, CMW, or TWRP image, this is the folder to copy those .img files to. Once you get your phone into fastboot mode and its plugged into the computer, just type into the command prompt:
Code:
fastboot flash recovery recovery.img
If you're just looking to reboot the phone into recovery
If you have a CWM or TWRP recovery just replace the recovery.img with whatever the .img file that you have. Also, as a tip instead of writing the entire file name, just press the first couple letters then press the tab key within the command prompt, it should fill in the rest. keep pressing tab until you get to the .img file name you want.
To avoid doing this again, maybe I can help... what were you trying to do to begin with? From the sound of it, you were trying to root the phone with the Root Toolbox Pro but it bricked, and then you tried to reboot into recovery and then got the red android... ?

befrosty8612 said:
As abnormal as it seems, your situation seems pretty normal... at least from my shoes. I went through the same scenario... I didn't know what adb was, or fastboot, etc. So, here's what I know
the fastboot commands work even if adb doesnt see it in the list of devices attached. Somehow it just works (as long as the phone is in fastboot mode).
If you're able to get to the fastboot mode, things should be okay. Just open a windows explorer window to the Platform-Tools, hold the shift key and right click on a blank space within the window, then click open command window here.
you should be able to pass any adb (if the phone is on and recognized) or fastboot (if phone is in fastboot mode) commands from that command prompt.
Also, if you have a stock recovery, CMW, or TWRP image, this is the folder to copy those .img files to. Once you get your phone into fastboot mode and its plugged into the computer, just type into the command prompt:
Code:
fastboot flash recovery recovery.img
If you're just looking to reboot the phone into recovery
If you have a CWM or TWRP recovery just replace the recovery.img with whatever the .img file that you have. Also, as a tip instead of writing the entire file name, just press the first couple letters then press the tab key within the command prompt, it should fill in the rest. keep pressing tab until you get to the .img file name you want.
To avoid doing this again, maybe I can help... what were you trying to do to begin with? From the sound of it, you were trying to root the phone with the Root Toolbox Pro but it bricked, and then you tried to reboot into recovery and then got the red android... ?
Click to expand...
Click to collapse
Thanks for the response. So, all I have to do is: go to fastboot and flash a stock recovery image file and it will automatically wipe the phone, cache, everything, and restore the operating system? Sounds awfully easy! I found some stock files in this post : http://forum.xda-developers.com/showthread.php?t=2001226&page=2 Are these the ones you used before?
Last question: I can flash CWM or TWRP but wont be able to access them if my bootloader is locked, correct? So flashing a stock recovery will allow me to have my stock phone back again, locked and un-rooted? I guess if I cant get it to work with the stock recovery then I can unlock the bootloader and do a CWM or TWRP recovery and then flash the stock .img files?
Thanks again for your help. I already had root with the motofail2go method which I like using but seems like when I try and use some generic root feature from apps from the app store that it will crash/brick the phone cuz obviously those apps are generalized and likely to brick certain percentage of devices....

Ok what does this mean? Something with the bootlaoder obviously. Does it need to be unlocked?
Code:
C:\Program Files (x86)\Android\android-sdk\platform-tools>fastboot flash recover
y qrecovery1.img
(bootloader) Variable not supported!
target reported max download size of 31457280 bytes
sending 'recovery' (5962 KB)...
OKAY [ 0.479s]
writing 'recovery'...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. total time: 0.755s
C:\Program Files (x86)\Android\android-sdk\platform-tools>
And on the phone screen it says "invalid image size for partition recovery" twice for both times I tried this method.

You will need to flash the system image as well if you want those, as the recovery image will only flash the recovery. The files in that link are for twrp only... so you'll have to be able to get there first.
With the custom recoveries, I'm not 100% sure whether or not you will be able to use them without being unlocked. I would wait to see if anyone else can answer that question for you, but if you did try it without an unlocked bootloader, you at least have the stock recovery to fall back on if needed.
Sent from my XT897 using xda app-developers app
---------- Post added at 09:16 PM ---------- Previous post was at 09:12 PM ----------
I'm thinking it could either be that your phone is full and the image you're flashing is too large to fit on the space available...
Or you're trying to flash custom software on a locked phone.
Hopefully someone is able to answer that a little better...
Sent from my XT897 using xda app-developers app

You can't alter the stock recovery (flash a custom recovery like twrp or cwm) in fastboot without having the bootloader unlocked. Your options are to unlock your bootloader, flash custom recovery, create a backup of your current setup, download one of the stock working backups, place it in the backups folder for twrp on your external sd card, and restore one of the known working backups in the development section (befrosty linked to one). Or you could use RSD lite to return to stock using a stock factory firmware flash. That involves connecting your phone to your PC and flashing the phone back to factory stock. Information on RSD Lite and links to the FXZ's can be found here.
http://forum.xda-developers.com/showthread.php?t=2095536
Sent from my XT897 using xda app-developers app

Help, Goes straight to TWRP on startup

Hello Everyone,
I am a Noob, Yes. Please help. I was trying to install TWRP onto my TF300T. I installed it Via ADB. Had it installed with my stock ROM. I tried to do a backup so I could flash CM10. It said it wasn't mounted. I tried again and then it reboot and now goes straight to TWRP. I can get my device on ADB via the cmd screen but it says that the device is attached in recovery and my serial number is now 01233456789ABCD. Have I completely bricked my tablet? Is there anything I can do? I have been searching the forums for literally hours and am at wits end. Any suggestions would be appreciated. Sorry if this has been gone over time and time again but I can't figure it out. Please help. Thanks
Marc

To add,
When I try to do anything via fastboot it just hangs waiting for device. I can't get it to go to the fastboot page on my tablet, it just goes straight to the TWRP page.

Let me guess... You were on the Asus 4.2.1 OTA release, and installed TWRP 2.4.4.0-JB...

splashg said:
Let me guess... You were on the Asus 4.2.1 OTA release, and installed TWRP 2.4.4.0-JB...
Click to expand...
Click to collapse
Yes, that would be correct. So I managed to reset the device and cold boot back to a working device. Now i'm still wanting to flash a custom recovery and change ROMS to cyanogenmod (had it on my S1 and loved it) but am a bit nervous. How do I reset my partition and clear the old TWRP and flash a working version of CWR via fastboot or a version of TWRP that will work with my OTA rom. I thought I had done quite a bit of research before hand but am feeling a bit overwhelmed now. I don't want to go through another twelve hours of trying every trick I can find on the internet to unbrick my device.
Thanks

Just a few other things to add. So now when i have my device connected to my computer in normal function i can recognize it when I enter adb devices on my cmd prompt. Then I do the fastboot reboot bootloader which it then sends it into the fastboot screen. type in adb devices and it doesn't recognize the device anymore. I try the commands to install the cwm recovery.img and my cmd screen goes through the normal steps saying it's completed it. Then i try to reboot the device through fastboot and it freezes on the bootload screen with the green box no longer flashing on the rck box. Hold power button for six seconds to reboot and i have a working device again. So now i'm lost. How do I reset everything so I can start over, repartition so I can flash a custom recovery and carry on. any help is appreciated.

I don't know how you got yours back, even the bootloader cold-booting linux won't go into the OS for me.
That said, AFAIK, TWRP 2.4.4.0-4.2 or 2.5.0.0-4.2 are the only ones that will work with the 4.2.1 OTA update. Let me know if you somehow manage to get either on there because I can't seem to flash anything.

splashg said:
I don't know how you got yours back, even the bootloader cold-booting linux won't go into the OS for me.
That said, AFAIK, TWRP 2.4.4.0-4.2 or 2.5.0.0-4.2 are the only ones that will work with the 4.2.1 OTA update. Let me know if you somehow manage to get either on there because I can't seem to flash anything.
Click to expand...
Click to collapse
I tried flashing the new correct version of TWRP. it just freezes on the rck tab of the bootloader. It goes through the process on fastboot on my cmd prmt but does nothing on the tablet end. At least I have a working device on 4.2.1 just frustrating that TW didn't state that there is a 4.2 version not just a JB version. So now I can't get OTA updates and can't flash any custom or stock ROM's. So I'm permanently stuck with 4.2 but it's better than being stuck with a brick I guess. This isn't my first time rooting, flashing or working with ADB and fastboot. Did my research before flashing the custom recovery and thought I followed TW's steps very accurately. I hope that they update their site to stop a large number of people soft or hard bricking their devices. I at least can hold out hope that someone will figure out how to re install the bootloader. There has to be a fix as the rest of my device works so the motherboard isn't shot. Good luck. Let me know if anything or anyone figures it out.

lomoski said:
I tried flashing the new correct version of TWRP. it just freezes on the rck tab of the bootloader. It goes through the process on fastboot on my cmd prmt but does nothing on the tablet end. At least I have a working device on 4.2.1 just frustrating that TW didn't state that there is a 4.2 version not just a JB version. So now I can't get OTA updates and can't flash any custom or stock ROM's. So I'm permanently stuck with 4.2 but it's better than being stuck with a brick I guess. This isn't my first time rooting, flashing or working with ADB and fastboot. Did my research before flashing the custom recovery and thought I followed TW's steps very accurately. I hope that they update their site to stop a large number of people soft or hard bricking their devices. I at least can hold out hope that someone will figure out how to re install the bootloader. There has to be a fix as the rest of my device works so the motherboard isn't shot. Good luck. Let me know if anything or anyone figures it out.
Click to expand...
Click to collapse
I finally gave up, sent mine in today, it will cost but what the hell, i want my tablet in working order. I've tried the remedies myself, to no avail.
So off to ASUS.

Let me know what they end up charging you. I did a service request on-line, but haven't heard back yet.

steveb05 said:
Let me know what they end up charging you. I did a service request on-line, but haven't heard back yet.
Click to expand...
Click to collapse
I won't know how much it will cost until the unit is in their hands. I initiated my RMA online as well, they told me i will be contacted by phone after they examine it, I'm prepared to invest another 100 bucks as i got the unit for $299. I'll be hesitant to go much higher. I will post a number when i hear from them, if they haven't replied back to you.

I've got the same problem on my TF300T.
I'm going to try to get it working.
Not entirely sure what caused it, since I had used encryption in cm10.1 prior to flashing Asus stock 4.2.1.
BTW, I've been able to get back to fastboot by running adb reboot bootloader when TWRP is loaded.
Update: Seems to be that new 10.6.x.x bootloader... gotta love Asus :-/
--- Update II----
I can't flash anything in fastboot anymore :-/

[Q] Bricked TF300T (APX mode only, no nvflash) – any hope?

I bricked a TF300T today, and I'd like to know if there is possibility that it might be repaired.
I was attempting to install CyanogenMod 10.1 on the tablet for my friends, which I offered to do since I have a bit of experience doing similar on other devices. It was running Android 4.2, and had the latest firmware (v10.6.1.15.3, WW). After researching the XDA forums, I unlocked and rooted the device, and installed the TWRP recovery (2.5.0.0). I used TWRP to flash CM 10.1 and the Google apps, but when I tried to boot I got stuck at the Asus logo. After some more research I realized that the official release of CM doesn't work with the 4.2 bootloader, and that if I wanted to install that ROM I would need to downgrade my bootloader (right?).
The trouble occurred during the downgrade. I downloaded the 10.4.2.20 firmware and used flashboot to flash it. The flash completely successfully and I was going to run "flashboot reboot." Thinking I'd save keystrokes on the command line, I hit the up arrow to call up my last command, and meant to delete the last half of it, but I managed to hit 'enter' instead, starting the flash over again. I cancelled the command (^C), which might not have been wise -- but then I made my dumbest move, and powered the device off. (I'm not really sure why; I guess I assumed I'd still be able to get into fastboot mode.)
Now the device will not boot at all, except into APX mode -- i.e., the screen is blank, but when plugged into the computer the device registers. From what I've read here, there isn't really anything useful I can do in APX mode, given that I never setup nvflash, and I can't figure out any way of getting the tablet to do anything else.
Is there anything I've missed? Is there anything I could accomplish by cracking open the tablet (popping out the battery)? I've seen references to replacing the logic board – would that work, and how should I go about this? I know most if not all of these questions have been answered in different places before, and I tried to do my homework, but I figured I'd ask in case anyone had new experience or expertise to share.

I think to only solution is to replace the main board OR buy a new tablet :'(
Sent from my ASUS Transformer Pad TF300T

jay-roc said:
I bricked a TF300T today, and I'd like to know if there is possibility that it might be repaired.
I was attempting to install CyanogenMod 10.1 on the tablet for my friends, which I offered to do since I have a bit of experience doing similar on other devices. It was running Android 4.2, and had the latest firmware (v10.6.1.15.3, WW). After researching the XDA forums, I unlocked and rooted the device, and installed the TWRP recovery (2.5.0.0). I used TWRP to flash CM 10.1 and the Google apps, but when I tried to boot I got stuck at the Asus logo. After some more research I realized that the official release of CM doesn't work with the 4.2 bootloader, and that if I wanted to install that ROM I would need to downgrade my bootloader (right?).
The trouble occurred during the downgrade. I downloaded the 10.4.2.20 firmware and used flashboot to flash it. The flash completely successfully and I was going to run "flashboot reboot." Thinking I'd save keystrokes on the command line, I hit the up arrow to call up my last command, and meant to delete the last half of it, but I managed to hit 'enter' instead, starting the flash over again. I cancelled the command (^C), which might not have been wise -- but then I made my dumbest move, and powered the device off. (I'm not really sure why; I guess I assumed I'd still be able to get into fastboot mode.)
Now the device will not boot at all, except into APX mode -- i.e., the screen is blank, but when plugged into the computer the device registers. From what I've read here, there isn't really anything useful I can do in APX mode, given that I never setup nvflash, and I can't figure out any way of getting the tablet to do anything else.
Is there anything I've missed? Is there anything I could accomplish by cracking open the tablet (popping out the battery)? I've seen references to replacing the logic board – would that work, and how should I go about this? I know most if not all of these questions have been answered in different places before, and I tried to do my homework, but I figured I'd ask in case anyone had new experience or expertise to share.
Click to expand...
Click to collapse
APX mode is useless without nvflash installed and nvflash can only be installed while on ICS and once you leave ICS you can't go back.
Some Info: the vehicles to recover without nvflash are
1. recovery - stock or twrp
2. adb
3. fastboot
Do any of these work?
Try this link to find ways you may not have used yet -to get to the bootloader - thus recovery or fastboot
[GUIDE] Enter APX mode or Bootloader-recovery menu!
For future reference here is the way I see the recovery and rom matching issue.
4.1 bootloader - 10.4.2.9, 10.4.2.13, 10.4.2.17, 10.4.2.18, 10.4.2.20 - twrp openrecovery-twrp-2.5.0.0-tf300t-JB.blob
4.2 bootloader - 10.6.1.8 - twrp openrecovery-twrp-2.4.4.0-tf300t-4.2.blob
4.2.1 bootloader - 10.6.1.15.3 - twrp openrecovery-twrp-2.5.0.0-tf300t-4.2.blob

tobdaryl said:
APX mode is useless without nvflash installed and nvflash can only be installed while on ICS and once you leave ICS you can't go back.
Some Info: the vehicles to recover without nvflash are
1. recovery - stock or twrp
2. adb
3. fastboot
Do any of these work?
Try this link to find ways you may not have used yet -to get to the bootloader - thus recovery or fastboot
[GUIDE] Enter APX mode or Bootloader-recovery menu!
Click to expand...
Click to collapse
Thanks for the response. I've already tried the relevant methods in the guide, except for disconnecting the battery. I can get into APX mode -- the tablet registers as an APX device when plugged into the computer -- but I can't get it to enter the bootloader, so recovery, adb, and fastboot do not work. At this point I don't have much hope that the device will ever boot again without replacing the motherboard.

jay-roc said:
Thanks for the response. I've already tried the relevant methods in the guide, except for disconnecting the battery. I can get into APX mode -- the tablet registers as an APX device when plugged into the computer -- but I can't get it to enter the bootloader, so recovery, adb, and fastboot do not work. At this point I don't have much hope that the device will ever boot again without replacing the motherboard.
Click to expand...
Click to collapse
I'm sorry, I hoped the guide would give you a chance of recovery.

I definitely appreciate the help, and the guide's a great resource.
tobdaryl said:
I'm sorry, I hoped the guide would give you a chance of recovery.
Click to expand...
Click to collapse

jay-roc said:
I definitely appreciate the help, and the guide's a great resource.
Click to expand...
Click to collapse
You are welcome!
I had wished for better results.
Good Luck!

noahvt said:
I think to only solution is to replace the main board OR buy a new tablet :'(
Click to expand...
Click to collapse
Is there any tips for buying mainboard? Should it be exactly the same as in my tablet (I mean the same region and, therefore, version of ROM installed), maybe serials.
I have a bricked TF300T, and the only way I have to resurrect it - MB replacement. So, please, ANY info will be useful. Thanks in advance.

try to get it into fastboot somehow - i was stuck in apx too but with a bit of trying i was able to get to fastboot (try resetbutton + vol-down, let it completly drain of power, charge it back and try again)
here is what i did after i regained fastboot:
http://forum.xda-developers.com/showpost.php?p=44244313&postcount=12
gl
-Buster

Buster99 said:
try to get it into fastboot somehow - i was stuck in apx too but with a bit of trying i was able to get to fastboot (try resetbutton + vol-down, let it completly drain of power, charge it back and try again)
here is what i did after i regained fastboot:
http://forum.xda-developers.com/showpost.php?p=44244313&postcount=12
gl
-Buster
Click to expand...
Click to collapse
I'm so damn appreciated! Thank you so much)) I'd add this way to get to fastboot - adb reboot fastboot - just from faulty CWM. Other way it didn't worked.

I got mine working this way
Link to my thread --> http://forum.xda-developers.com/showthread.php?p=45120193#post45120193
Hope it helps. Try It!

ozkrtech said:
Link to my thread --> http://forum.xda-developers.com/showthread.php?p=45120193#post45120193
Hope it helps. Try It!
Click to expand...
Click to collapse
I have the same problem...
My TF300T got bricked and now i cant boot at all anymore, i just see the Asus logo.
Vol down and power doesnt work but i think i can boot it into APX mode, screen stays black but my pc recognises an APX device.
At first my pc didnt install the driver but than i found APX drivers in these forums.
I've downloaded the APX drivers from a thread and i can choose to install various drivers, i tried all of them.
The one i think i need is the Asus Transformer ADB interface driver but this one along with every other one i can choose from doesn't work.
After installing and trying fastboot devices and adb devices i never had a device name show up
im kinda stuck right now
Can anyone please give me some advice ?
Cheers, any help is appreciated
marty

martyzzz said:
I have the same problem...
My TF300T got bricked and now i cant boot at all anymore, i just see the Asus logo.
Vol down and power doesnt work but i think i can boot it into APX mode, screen stays black but my pc recognises an APX device.
At first my pc didnt install the driver but than i found APX drivers in these forums.
I've downloaded the APX drivers from a thread and i can choose to install various drivers, i tried all of them.
The one i think i need is the Asus Transformer ADB interface driver but this one along with every other one i can choose from doesn't work.
After installing and trying fastboot devices and adb devices i never had a device name show up
im kinda stuck right now
Can anyone please give me some advice ?
Cheers, any help is appreciated
marty
Click to expand...
Click to collapse
Can you explain me step by step what you did to get bricked? Are you on bootloader 4.1 or 4.2+? 10.4.x.x is 4.1 and 10.6.x.x is 4.2+

ozkrtech said:
Can you explain me step by step what you did to get bricked? Are you on bootloader 4.1 or 4.2+? 10.4.x.x is 4.1 and 10.6.x.x is 4.2+
Click to expand...
Click to collapse
Bought the Asus tab a year back and kept it original and updated by Asus for a few months.
Begin this year i unlocked it through a guide here on XDA (i dont thin through the Asus APK but another way).
After it succesfully unlucked (you could see "your device is unlocked" in the left top of the Asus boot screen i installed CWM.
After CWM i installed Cyogenmod 10.1 and kept it updated for months
This was all in the beginning of this year...
In june after updating Cyogenmod 10.1 to a newer version it wouldnt boot up anymore (i still had acces to my CWM recovery at this time).
So i switched back to the last working Cyogenmod 10.1 version (think it was 15th or 16th june).
I left it again for 2 months, still everything was fine till i saw that Cyogenmod 10.2 was out on XDA.
The upcomming is all last week;
First i tried to install 10.2 through CWM but my tab wouldnt boot up.
Than i switched recovery through fastboot because i have read that 10.2 was only compatible with TWRP 2.5+ so i got the latest TWRP
(2.6.0.0 i think)
After booting into TWRP i fully wiped the tab (i might have wiped everything because i dont know TWRP so well), after the wipe i wanted to install 10.2 again.
My tab still didnt boot so i got anctious and wanted to switch back to my latest version 10.1 (june 2013 that did work) so i could at least use my tab again.
Installing 10.1 again didnt work through TWRP, after that i came to the conclusion that i couldt install any rom anymore, at every rom i got an error in TWRP so i thought i had the wrong TWRP installed. (see my other post for a link to the screenshot of the error msge, i just cant find it atm).
Last but not least i tried to load my old CWM again as recovery, after i did this i couldnt get into recovery anymore...
Thans basicly the whole story.
Hope some1 can help me out.
Thanks in advance !
Cheers

martyzzz said:
Bought the Asus tab a year back and kept it original and updated by Asus for a few months.
Begin this year i unlocked it through a guide here on XDA (i dont thin through the Asus APK but another way).
After it succesfully unlucked (you could see "your device is unlocked" in the left top of the Asus boot screen i installed CWM.
After CWM i installed Cyogenmod 10.1 and kept it updated for months
This was all in the beginning of this year...
In june after updating Cyogenmod 10.1 to a newer version it wouldnt boot up anymore (i still had acces to my CWM recovery at this time).
So i switched back to the last working Cyogenmod 10.1 version (think it was 15th or 16th june).
I left it again for 2 months, still everything was fine till i saw that Cyogenmod 10.2 was out on XDA.
The upcomming is all last week;
First i tried to install 10.2 through CWM but my tab wouldnt boot up.
Than i switched recovery through fastboot because i have read that 10.2 was only compatible with TWRP 2.5+ so i got the latest TWRP
(2.6.0.0 i think)
After booting into TWRP i fully wiped the tab (i might have wiped everything because i dont know TWRP so well), after the wipe i wanted to install 10.2 again.
My tab still didnt boot so i got anctious and wanted to switch back to my latest version 10.1 (june 2013 that did work) so i could at least use my tab again.
Installing 10.1 again didnt work through TWRP, after that i came to the conclusion that i couldt install any rom anymore, at every rom i got an error in TWRP so i thought i had the wrong TWRP installed. (see my other post for a link to the screenshot of the error msge, i just cant find it atm).
Last but not least i tried to load my old CWM again as recovery, after i did this i couldnt get into recovery anymore...
Thans basicly the whole story.
Hope some1 can help me out.
Thanks in advance !
Cheers
Click to expand...
Click to collapse
What happends when you press volume down+ power?
It jeeps rebooting or it goes to black screen? Have you tried pressing the reset button is below the micro sdcard slot.
You should be able to boot any recovery.

is I recall correctly cm switched partition layout to 4.2 on tf300.
if you still have fastboot try my guide to flash stock and then flash recovery and cm10.2. since it sounds a lot like my error I had with cm it should work for you as well.
good luck
Sent from my TF300T using xda app-developers app

ozkrtech said:
What happends when you press volume down+ power?
It jeeps rebooting or it goes to black screen? Have you tried pressing the reset button is below the micro sdcard slot.
You should be able to boot any recovery.
Click to expand...
Click to collapse
When i press vol down+power i get the asus boot screen for a minute or 2, the tab switches off and on again to the same boot screen.
I cant boot into recovery
---------- Post added at 06:51 PM ---------- Previous post was at 06:42 PM ----------
Buster99 said:
is I recall correctly cm switched partition layout to 4.2 on tf300.
if you still have fastboot try my guide to flash stock and then flash recovery and cm10.2. since it sounds a lot like my error I had with cm it should work for you as well.
good luck
Sent from my TF300T using xda app-developers app
Click to expand...
Click to collapse
I dont have fastboot in any way.
I can only power on the device with volume up + power to enter APX mode, than only my pc sees a USB device.
I tried a lot of differtent drivers but for nome of them i can ADB of Fastboot to the device.
It would help if someone that has managed to unbrick through APX mode posted the right driver for a TF300T
Cheers

have you tried the apx drivers that come with the sdk?
Sent from my GT-I9505 using xda app-developers app

Buster99 said:
have you tried the apx drivers that come with the sdk?
Sent from my GT-I9505 using xda app-developers app
Click to expand...
Click to collapse
Ive tried searching in the SDK forders but i cant find any.
If i try to install drivers automaticly and than point to the root SDK folder i get the windows msge the best drivers are already installed (no matter what driver is in stalled at that time)

martyzzz said:
Ive tried searching in the SDK forders but i cant find any.
If i try to install drivers automaticly and than point to the root SDK folder i get the windows msge the best drivers are already installed (no matter what driver is in stalled at that time)
Click to expand...
Click to collapse
don't just point at the folder
manually select the driver for the device from android-sdk\extras\google\usb_driver
gl

Insignia Flex

Anybody have one? It's Best Buy's brand tablet.
insigniaproducts.com/products/computer-speakers-accessories/NS-14T002.html
(can't post a link...)
Just picked up a Flex 8 on Black Friday. Not bad for $80. Not sure if I'd pay full price for it though.
It seems good for the price so far, except I'm having a rough time trying to root it.
Anyone have one and root it?

Employee here and I had to pouch one up as well for the price of $80. Now to figure out root.
Sent from my SPH-L710 using xda app-developers app

Let us know if you get it.
I've tried Bin4ry, doomlord, tpsparky, played around with it myself a bit. Still not luck. Closest I got is normal on Bin4ry. Just when it reboots, it has no root privaledges. su is in /data/local/tmp but it fails to do anything...

I haven't messed around with it until this very moment. I will admit that the price is killer but initial impression with the device could be better. I was impressed and I mean really impressed with its quadrant score. I'll root this device later today. Black Friday sales and I am tired.
---------- Post added at 01:20 AM ---------- Previous post was at 01:18 AM ----------
I found a link to root this device on both ICS and jellybean. I will personally look into it tomorrow but I will post it if you would like to go ahead. The guide itself was written for ICS but later down the thread you will find another link to a working root for jellybean.
http://androidforums.com/insignia-flex-all-things-root/661247-how-root-insignia-flex.html
Please root at your own discresion and I sure hope you purchased a protection plan (GSP) for your tablet.

also picked this up at my BB, was surprised when i walked in at 3pm and they still had about 10. i want to root too

We had a large quantity to sell as well and they all went. It is honestly not half bad. And I would really recommend getting the GSP for the tablet in case of anything. Will report back after rooting.

Let us know if you have any luck. I found the link you posted before which led me to try Bin4ry. The script seems to be updated for JB in general but still had no luck. I'm on a Mac and haven't tried any of the windows rooting apps, like posted at the bottom of that thread. I do have a windows partition and would be willing to try that method if needed. That chinese one at the bottom seems shady regardless though.. I hope there is an alternative to that

Is there a way to flash clockworkmod onto this tablet?

rekagear20 said:
Is there a way to flash clockworkmod onto this tablet?
Click to expand...
Click to collapse
I managed to get the CX-803 version of CWM for Rockchip 3066 from AndroTab.info to work by replacing its kernel with ours by unpacking and repacking with RK3xxx-Firmware-Tools by Sergio.
Note: This is for the Insignia NS-14T002 (aka iRiver NS-14T002) tablet that shipped with Android 4.2.2
Be EXTREMELY careful! Highly recommend you dump your current kernel and recovery partitions and save them somewhere before flashing anything.
If for some reason the recovery doesn't work, you can flash your stock recovery back as long as you can get back into root shell. But, if it fails to boot normally, I have no idea how to fix it. I have not been able to get any of the Rockchip flashing utilities to recognize the tablet so far, in bootloader mode (these devices have no fastboot) or otherwise. So don't blame me if you somehow brick your tablet.
You have been warned!!
CWM & Stock* Recovery image for NS-14T002
* if for some reason you can't back up your own, but again highly recommend backing up your existing recovery in case it's different from mine
You need root, and you need to do the install from root shell (don't forget to su) as described here.
I used /data/local instead of /dev - anywhere writable should be okay.
To boot into recovery:
adb reboot recovery
power off tablet, disconnect USB, press and hold Vol+ and Power until recovery comes up.
USB disconnect is not a strict requirement, but the battery status thing tends to get in the way.
In stock recovery, push Vol+ and Vol- simultaneously to bring up the menu. CWM menu should be visible at launch.
install petrus's Reboot App and use it to Reboot into recovery
Note: In CWM recovery you can swipe up for Vol+ (move up), swipe down for Vol- (move down), swipe left for Power (select), and swipe right for Back.

Re:Insignia Flex Tablet
I actually just purchased one of these last night. It was on sale at Best Buy for $99! I have successfully rooted it and it actually works great! I used Kingo Root to root but first I installed pda net first to install the necessary drivers. I have used this program to root several Android devices and haven't had a problem thus far!
http://www.kingoapp.com/

cramamarshall said:
I actually just purchased one of these last night. It was on sale at Best Buy for $99! I have successfully rooted it and it actually works great! I used Kingo Root to root but first I installed pda net first to install the necessary drivers.
Click to expand...
Click to collapse
Great news! I didn't have luck with that one but it might have been the machine I was using at the time.
Just to confirm, your model came with Jellybean 4.2, Model NS-14T002?
The previous version with Ice Cream Sandwich 4.0 was easier to root.
Sent from a device with no keyboard. Please forgive typos, they may not be my own.

bhiga said:
Great news! I didn't have luck with that one but it might have been the machine I was using at the time.
Just to confirm, your model came with Jellybean 4.2, Model NS-14T002?
The previous version with Ice Cream Sandwich 4.0 was easier to root.
Sent from a device with no keyboard. Please forgive typos, they may not be my own.
Click to expand...
Click to collapse
Yes my device came with 4.2.2 Jelly Bean! My first attempt using Kingo Root it did not see my device. Windows would not install the drivers needed. So I installed PDA net for windows and choose other in the program and once it was done installing it had configured the necessary drivers for Kingo Root to find my tablet and it rooted fine within a couple minutes after that! :good:

help!
klowdhaus said:
Anybody have one? It's Best Buy's brand tablet.
insigniaproducts.com/products/computer-speakers-accessories/NS-14T002.html
(can't post a link...)
Just picked up a Flex 8 on Black Friday. Not bad for $80. Not sure if I'd pay full price for it though.
It seems good for the price so far, except I'm having a rough time trying to root it.
Anyone have one and root it?
Click to expand...
Click to collapse
I was wondering, because I rooted my insignia flex 8 tablet and downloaded an app to try and customize the navigation bar and the developer provided a way on how to do it but said it was risky and took the risk anyway. Unfortunately, after turning on my tablet, it gets stuck on the insignia logo which I'm assuming it is stuck in the boot screen. I emailed the developer on how to fix this and said to flash a ROM to it. But I am just wondering if I am able to still do this even if my tablet gets stuck on the boot screen and freezes. I used ultimate dynamic navbar lite to try and customize my navbar.

arahmahndy said:
I was wondering, because I rooted my insignia flex 8 tablet and downloaded an app to try and customize the navigation bar and the developer provided a way on how to do it but said it was risky and took the risk anyway. Unfortunately, after turning on my tablet, it gets stuck on the insignia logo which I'm assuming it is stuck in the boot screen. I emailed the developer on how to fix this and said to flash a ROM to it. But I am just wondering if I am able to still do this even if my tablet gets stuck on the boot screen and freezes. I used ultimate dynamic navbar lite to try and customize my navbar.
Click to expand...
Click to collapse
I don't have the tablet anymore as it was a gift for a family member that lives elsewhere (I just wanted root so I could remote control it with TeamViewer QuickSupport), but will try to help from my notes and memory.
Flashing ROM may be difficult.
There is no fastboot on these Rockchip devices...
I couldn't find a way to flash without it being bootable and accessible via ADB
None of the Rockchip flashing tools would recognize it, even when I thought I got it booted into flash mode - it loaded drivers, but the flash tools still didn't see it.
The only way I know how to flash is to use a flash tool via ADB root shell.
Have you tried plugging it into USB on computer and booting it? Even if it doesn't reach the launcher, maybe it is accessible from ADB?
If you can access ADB, you may be able to reverse whatever the app changed from ADB shell and uninstall the app. (Politely ask the author for help)
You might be able to flash the system image I took too, but that has potential to brick it even worse.
If you have custom recovery loaded, you should just be able to restore from a backup.
If you don't have custom recovery loaded, things get a little more hairy...
You can try booting into Safe mode, maybe it'll bypass the offending app.
Power off tablet
Unplug USB*
Press and hold Vol- and Power until (hopefully) it completely boots
Try booting into standard recovery and see what your options are there - Factory Reset might help (depends what was changed and where)
Power off tablet
Unplug USB*
Press and hold Vol+ and Power until recovery comes up (Android with open chest)
Press Vol+ and Vol- simultaneously to bring up the menu.
* while unplugging USB isn't really required, because a battery app launches shortly afterward, it can make getting into recovery and safe mode more difficult
The folks over at Freaktab and Vondroid are really the experts at this Rockchip stuff.
For reference, the platform is RK3066, but there are many variations of the platform (different WiFi, memory configuration, etc) so you can't just grab any ROM.

Thank you!
bhiga said:
I don't have the tablet anymore as it was a gift for a family member that lives elsewhere (I just wanted root so I could remote control it with TeamViewer QuickSupport), but will try to help from my notes and memory.
Flashing ROM may be difficult.
There is no fastboot on these Rockchip devices...
I couldn't find a way to flash without it being bootable and accessible via ADB
None of the Rockchip flashing tools would recognize it, even when I thought I got it booted into flash mode - it loaded drivers, but the flash tools still didn't see it.
The only way I know how to flash is to use a flash tool via ADB root shell.
Have you tried plugging it into USB on computer and booting it? Even if it doesn't reach the launcher, maybe it is accessible from ADB?
If you can access ADB, you may be able to reverse whatever the app changed from ADB shell and uninstall the app. (Politely ask the author for help)
You might be able to flash the system image I took too, but that has potential to brick it even worse.
If you have custom recovery loaded, you should just be able to restore from a backup.
If you don't have custom recovery loaded, things get a little more hairy...
You can try booting into Safe mode, maybe it'll bypass the offending app.
Power off tablet
Unplug USB*
Press and hold Vol- and Power until (hopefully) it completely boots
Try booting into standard recovery and see what your options are there - Factory Reset might help (depends what was changed and where)
Power off tablet
Unplug USB*
Press and hold Vol+ and Power until recovery comes up (Android with open chest)
Press Vol+ and Vol- simultaneously to bring up the menu.
* while unplugging USB isn't really required, because a battery app launches shortly afterward, it can make getting into recovery and safe mode more difficult
The folks over at Freaktab and Vondroid are really the experts at this Rockchip stuff.
For reference, the platform is RK3066, but there are many variations of the platform (different WiFi, memory configuration, etc) so you can't just grab any ROM.
Click to expand...
Click to collapse
Thanks for the information! I know I have ADB from rooting my tablet so I'm gonna check how that is when I get home and I have found some rockship information on vondroid so I will check that out also. Thanks for the reply again!

arahmahndy said:
Thanks for the information! I know I have ADB from rooting my tablet so I'm gonna check how that is when I get home and I have found some rockship information on vondroid so I will check that out also. Thanks for the reply again!
Click to expand...
Click to collapse
If you can access ADB then try loading the CWM recovery I posted above. If you can at least get CWM up, at worst case I can give you a copy of my stock backup to restore.
Sent from a device with no keyboard. Please forgive typos, they may not be my own.

arahmahndy said:
Thanks for the information! I know I have ADB from rooting my tablet so I'm gonna check how that is when I get home and I have found some rockship information on vondroid so I will check that out also. Thanks for the reply again!
Click to expand...
Click to collapse
Did you get things sorted out?

If anyone is interested or needs it, Insignia sent me the GPL source.
You can also request it directly from them like it says on the website but it took a week or two (they might not have had a procedure in place yet, the agent had to forward my request to a different department) and I had completely forgotten until an unexpected package arrived.

Performance NS-15at10, ta120, ITQ701
Just thought someone might want to know, kingo root works, updated to 4.4.2, Booster plus battery saver pro is worth the money, better than 3c so far, still looking for more sources, any advice or help is appreciated especially for a recovery, dual bootloaders, ugh

cramamarshall said:
I actually just purchased one of these last night. It was on sale at Best Buy for $99! I have successfully rooted it and it actually works great! I used Kingo Root to root but first I installed pda net first to install the necessary drivers. I have used this program to root several Android devices and haven't had a proble
Can I install drivers without PC?
Click to expand...
Click to collapse

Failed to flash stock image (maybe full bricked?)

Hi all,
Today I tried to flash an older version of the stock rom (v1.2.1) and thought I didn't need to flash userdata.img. That was a big mistake..
Now the tablet stuck at a bootloop. After that I thought I could simply flash twrp over the bootloader to peform a /cache & /data wipe so that I can fix the bootloop.
And now we come to the other BIG problem. I can't access the bootloader. It directly boots up the tablet with the Nvidia logo. Is there any solution to fix the tablet?
I tried at the bootloop to enter via adb into the bootloader but my PC isn't recognize my device (probably no usb debugging).
There is no way to rescue it? No apx drivers out there?

Your message seems to be unclear about one very important thing:
1. Are you able to successfully access the bootloader? I don't mean your custom recovery. I mean the black screen with very small font words with your serial and shows whether your bootloader is Locked or Unlocked.
From where I'm sitting, it looks like you flashed v1.2.1 without using "flash -w", as well as forgetting to flash ALL the stock img files. Next, it looks like you're expecting a direct boot into the bootloader, which is not possible. You need to hold down the Vol_down button and then hold the Power button until the screen comes on, THEN you need to let go of the Power BUT KEEP HOLDING the Vol_down. If done correctly, you should be at the bootloader.
From the bootloader, you will not be able to run adb commands. Instead, the bootloader takes "fastboot" commands. All this is assuming you've installed the latest nVidia Shield Family drivers from the nvidia gameworks download site.

amartolos said:
Your message seems to be unclear about one very important thing:
1. Are you able to successfully access the bootloader? I don't mean your custom recovery. I mean the black screen with very small font words with your serial and shows whether your bootloader is Locked or Unlocked.
From where I'm sitting, it looks like you flashed v1.2.1 without using "flash -w", as well as forgetting to flash ALL the stock img files. Next, it looks like you're expecting a direct boot into the bootloader, which is not possible. You need to hold down the Vol_down button and then hold the Power button until the screen comes on, THEN you need to let go of the Power BUT KEEP HOLDING the Vol_down. If done correctly, you should be at the bootloader.
From the bootloader, you will not be able to run adb commands. Instead, the bootloader takes "fastboot" commands. All this is assuming you've installed the latest nVidia Shield Family drivers from the nvidia gameworks download site.
Click to expand...
Click to collapse
Thanks for your answering. I flashed all .imgs, the blob file and the .dtb file . Everything but not the userdata.img. I can't access the bootloader with holding down the vol down + power button. I only can access the apx mode with power + vol up.

ThunderArts said:
Thanks for your answering. I flashed all .imgs, the blob file and the .dtb file . Everything but not the userdata.img. I can't access the bootloader with holding down the vol down + power button. I only can access the apx mode with power + vol up.
Click to expand...
Click to collapse
I notice in your sig that you do in fact seem to have a fully working new replacement tablet. That got me thinking along the following:
1. new tablet is fully functional, old one is not
2. both tablets have the same hardware spec
3. pull firmware from new one, and somehow get it onto the old one
4. hopefully old tablet should work!
The biggest problem is step 3... I only know of nvflash that might be able to help here, but I've never used it myself so I'm completely useless here. Maybe someone more knowledgeable could help out here, but otherwise it seems like you might be out of options.
If you do want to take a stab at nvflash yourself, THIS PAGE has a nice writeup of what some commands do, BUT BEWARE! It's not for our device, so don't just copy-paste commands! As long as you're not writing things to the new tablet, it couldn't hurt to try stuff, right?

It wish someone could help me with NvFlash because I have no knowledge with it.
So it's possible to make a copy of the system of my working tablet and flash it on my old tablet with NvFlash?
I hope someone helpful with NvFlash experience could help me out.
Btw I need to have an un-blob'd stock rom version to get it back alive? Afaik is there no public version.

NVflash is only useful if you have backed up using it BEFORE you brick it.

sbdags said:
NVflash is only useful if you have backed up using it BEFORE you brick it.
Click to expand...
Click to collapse
I have a replacement tablet. I could make a backup from it and use it with my bricked tablet. Do you know how this could work? (As I said I don't have experience with Nvflash yet.)

-deleted-

ThunderArts said:
I have a replacement tablet. I could make a backup from it and use it with my bricked tablet. Do you know how this could work? (As I said I don't have experience with Nvflash yet.)
Click to expand...
Click to collapse
No the blobs are specific to the device.

sbdags said:
No the blobs are specific to the device.
Click to expand...
Click to collapse
Okay. So it seems that there is no way to rescue it. Btw is there no accessible bootloader in OTA 1.2.1 because I flashed the boot.img without any error and I don't understand why I can't access it.

sbdags said:
NVflash is only useful if you have backed up using it BEFORE you brick it.
Click to expand...
Click to collapse
can you actually back up anything for nvflash? afaik there's nothing that works on the tegra k1 yet

Bogdacutu said:
can you actually back up anything for nvflash? afaik there's nothing that works on the tegra k1 yet
Click to expand...
Click to collapse
Indeed - I was just talking about nvflash use in general. I haven't seen it used since tegra 3.