The Problem/Symptoms: I've been running a version of last CM10.2 for the past year. On February 20th, I was able to send a single SMS and then subsequent texts failed. I could still receive SMS, send/receive MMS, send/receive calls and send/receive data. If I toggle airplane mode/reboot I can send another SMS and then subsequent sms are undeliverable.
What wont work: Flashing to CM11 does not change the issue.
Disabling Voice+ does not change the issue
Factory Reset does not change the issue
Workarounds: Toggle Airplane mode
Switching Mobile Network to CDMA only (not permanent)
Change your number to a different area code
Going back to a Touchwiz based ROM
The Solution
net-cat said:
Alright. I think I've refined my process and it results in having a newer radio as well as not having to ODIN things or do dd commands.
NOTE: This isn't fully tested. When I did this, my phone wasn't showing the issue. I did this after doing my original procedure, but the GPS stopped working after I updated the radio from VRALF2 to VRBMB1. You shouldn't need to do the original procedure for this to work, but I haven't tested that. At the very least, the original procedure still works and this one can be used afterward if you need the newer radio. (GSM support...)
Ideally, we'll want to get to a procedure that doesn't use ODIN or dd. Hopefully this is a step in that direction.
Requirements:
A rooted stock ROM of the VRUCML1/4.3 vintage. I used Scott's Stock Rooted Knox Free VRUCML1 - 4.3 - DeOdex - V2. (Thread here.)
VRBMB1 AIO Flash, available here. (Thread here.)
I'm going to assume you know how to boot into and use recovery.
NOTE: Do NOT let the stock ROM install any updates.
Starting with my CM11 M3 install, I did a nandroid backup. (Recovery is CWM Touch 6.0.4.5, but I doubt that matters.)
Flash the VRBMB1 AIO.
Wipe data and cache.
Flash the stock ROM.
Boot into the stock ROM.
The reprovisioning seems to happen as a part of ROM's initial boot up.
Send a few text messages to test. (I sent them to Twitter.)
Launch the Maps application, turn on your GPS and let it get a lock. If you don't, when you boot back into your ROM, you probably won't have working GPS.
This would be a good time to back up your IMEI if you haven't already done so.
Reboot into your recovery, wipe data/cache and restore your nandroid backup.
At this point, you'll be running your preferred ROM with a less archaic radio than my previous post.
DO NOT UPGRADE YOUR RADIO. The moment I upgraded my radio, the problem came back!
CM11 M3 will work just fine with the old radio. I've rebooted several times over the last few hours and it still works fine. (Time will tell if it's a long term fix or not.)
Click to expand...
Click to collapse
buffal0b1ll said:
I put a MB1 aoi zip in my dropbox for you. It's from invisblek.org which isn't working now for some reason https://www.dropbox.com/s/7b1aqspo40fxl00/VRBMB1.aio.zip
Click to expand...
Click to collapse
Notes: There are threads for the S4 with this identical problem. All updated information I have seen is listed above. If anyone knows more please post as I am going to keep this updated. If this does/doesn't work for you please post and let the community know. Feel free to hit the thanks button if it works for you.
This exact thing happened to me. I tried many fixes with no luck. After hours of hacking around in settings, I found a ROM of verizon's 4.3 OTA update and flashed that through ODIN. My texts are working just fine again. Kind of a cheap method of fixing my problem. I wish I could have taken more time to find a fix, but I needed to be able to communicate with people that day.
Stock 4.3 is kind of lame:
-4.3 is killing my battery faster than ever. CM11 had me going for days without charging and now I've needed to charge everyday.
-Stock 4.3 is laggier/slower than CM11. It tends to stutter for me.
-4.3 came with a new boot loader which no developers have exploited to install custom ROMs yet. This leaves you stuck with Verizon bloat. I hate all these damn apps. Going to try to safe root & see if I can't do some cleanup work.
Enough ranting. Just wanted to let you know you are not alone with this problem. Hopefully someone will figure it out. Missing my cyanogen mod already
It seems this problem has happened on other phones also running Cyanogenmod. I found this thread http://forum.xda-developers.com/showthread.php?t=2654822
It looks like the symptoms have all showed up at the same time approximately. (February 19th, 2014). Still looking for a better answer than going back to stock TW...
Edit: And another thread http://forum.xda-developers.com/showthread.php?t=2659280 This one suggests its all AOSP roms. But it seems many people are unaffected... I don't understand why/how.
edit2: and another thread http://forum.xda-developers.com/showthread.php?p=50627899
Just looking for more info
Sent from my SCH-I535 using Tapatalk
Dex954 said:
Just looking for more info
Sent from my SCH-I535 using Tapatalk
Click to expand...
Click to collapse
SO this is the current status that I know.
The problem happens for everyone with a 570/717 area codes + on verizon + running Cyanogenmod (possibly any AOSP) + while connected to LTE which started on Feb 20th (the day before KitKat came out offically).
Current Workarounds:
Switch to TouchWiz based Roms
Switch your radios to be CDMA only
Call verizon and switch your number to a different area code
I know the workarounds all suck but that all I know for now. Switching SIM cards won't work. If I anyone knows anything more please feel free to let me know.
I'm 717
Sent from my SCH-I535 using Tapatalk
I have still be unable to find a solution for this issue. I think I have to give up on CM and go back to a TW based. If I hear anything new I'll update the post but I don't have the time to be wasting on my phone at the moment. If someone finds or hears of a fix or if it magically goes away as it started, please post it.
And spread the word if there are any other ROMs that this is occurring on. It seems the pool of those affected is just too small.
I have already had to give up. Been running slows tw. I take it Verizon didn't get back to you?
Sent from my SCH-I535 using Tapatalk
Here is my thread guys. Same issue. I am gonna get on the fog horn with some Verizon buddies I have http://forum.xda-developers.com/showthread.php?t=2662658
DreamFX said:
Here is my thread guys. Same issue. I am gonna get on the fog horn with some Verizon buddies I have http://forum.xda-developers.com/showthread.php?t=2662658
Click to expand...
Click to collapse
Godspeed my friend.
Anyone try aosp to see if fixed yet?
Nope. Still having issues. Tried gummy and cm. TW based roms are fine. In 717.
capt730 said:
Nope. Still having issues. Tried gummy and cm. TW based roms are fine. In 717.
Click to expand...
Click to collapse
I try every other day. 717 for me. Remaining hopeful it's fixed... One day...
What gapps are you using? I have been using the PA 0Day gapps. Going to try the gapps package from invisblek and see if that makes a difference.
Sent from my GT-N5110 using XDA Premium 4 mobile app
capt730 said:
What gapps are you using? I have been using the PA 0Day gapps. Going to try the gapps package from invisblek and see if that makes a difference.
Sent from my GT-N5110 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
It won't. It isn't software dependent. People who had already flashed builds prior to the 20th magically had issues starting on that date, so it isn't a problem with new builds, and it only happens to those in the 717-570 areas so it isn't a problem with AOSP code. It has to be a Verizon network issue, I just have no idea how.
Sent from my SCH-I535 using XDA Premium 4 mobile app
I have run TW base roms almost 100% of the time. Prior to the 20th, I had flashed cm11 3 or 4 times to see if camera worked and was never on it more than a day. I also had issues where music in my sd card wasn't being found but it was fine on TW. Could it be the unified build causing an issue? I have no issues on Clean Rom 8, wicked sensations or old and slows stock based roms.
*Edit* I have installed Gummy and CM 11 with PA Mini Modular apps and the CM Gapps from Invisiblek, let it set up. I then shut it down, removed battery and sim and then put everything back in and still the same issue. 1st text message goes through, then the rest after that just fail. I tried regular message app, Hangouts and Verizon messaging. All same results. I go back to my CR8 backup and all is fine. It's bizarre because everything else seems to be working fine and is very fast & smooth.
capt730 said:
I have run TW base roms almost 100% of the time. Prior to the 20th, I had flashed cm11 3 or 4 times to see if camera worked and was never on it more than a day. I also had issues where music in my sd card wasn't being found but it was fine on TW. Could it be the unified build causing an issue? I have no issues on Clean Rom 8, wicked sensations or old and slows stock based roms.
*Edit* I have installed Gummy and CM 11 with PA Mini Modular apps and the CM Gapps from Invisiblek, let it set up. I then shut it down, removed battery and sim and then put everything back in and still the same issue. 1st text message goes through, then the rest after that just fail. I tried regular message app, Hangouts and Verizon messaging. All same results. I go back to my CR8 backup and all is fine. It's bizarre because everything else seems to be working fine and is very fast & smooth.
Click to expand...
Click to collapse
It can't be an issue with the unified builds because going back and flashing an older build yields the same results. If you're willing to make the trade-off, you can set your phone to CDMA only. Texts will send, but you'll have no 3G or 4G.
I'm ok with using CR8, Beans or other stock roms. Can't see paying for LTE and not using it lol. Was curious to see how aosp has been coming along and sms was really the only issue I was having.
Obaterista93 said:
It can't be an issue with the unified builds because going back and flashing an older build yields the same results. If you're willing to make the trade-off, you can set your phone to CDMA only. Texts will send, but you'll have no 3G or 4G.
Click to expand...
Click to collapse
I was using masta's 10.2 build for over 6 months without even thinking about flashing new builds. The 20th is when the problem started for me. Upgrading to CM11 didn't change it. I just installed Hyperdrive and everything is back to normal.
I wish I could go back to CM but it just doesn't work in this area. And I don't know what I can do about it,
Whisk_33 said:
I was using masta's 10.2 build for over 6 months without even thinking about flashing new builds. The 20th is when the problem started for me. Upgrading to CM11 didn't change it. I just installed Hyperdrive and everything is back to normal.
I wish I could go back to CM but it just doesn't work in this area. And I don't know what I can do about it,
Click to expand...
Click to collapse
Basically. I've talked to a few friends who have worked for carriers and stuff, and everyone is stumped as to how something like this can even happen. Luckily I'm pretty much always in WiFi so I can survive on CDMA only.
Related
I've had my S3 for about 3-4 months or so, and I've recently been having this problem.
The day I got it I rooted it and everything was going good, battery wasn't amazing, but definitely reasonable.
After the boot loader was unlocked, I unlocked it with the EZ unlock in the Play Store.
I then loaded up Synergy r50 (nightly at the time) and everything seemed improved.
Anyways, I have since then loaded Paranoid Android, CM10, Beans, and Incubus' Jellywiz.
I went to Beans after Synergy, everything was still fine, then I loaded up Jellywiz RLS7 for a day, and it ran extremely warm and I was dropping
a percentage of my battery every 2 minutes. I nandroided back to Beans, and had the overheat and battery drain problem on that too. I wiped everything and went to Synergy (newest nightly, forgot the number) (edit: added the ktoonsez kernel after many FC's) and the problem still exists. I'm also getting horrible cell signal (not 4g, 4g is fine) at my school where it used to be perfectly fine. Anyone know what I could possibly do besides returning it? I already used Odin to go back to the latest non-leaked stock, and it's still doing it. Thank you very much.
TL;DR: After flashing multiple roms, then flashing Jellywiz, my phone runs much too hot for comfort, borderline burning, battery life goes fast, and I get next to no signal at my school.
Thanks again for any help!
chisandwich said:
I've had my S3 for about 3-4 months or so, and I've recently been having this problem.
The day I got it I rooted it and everything was going good, battery wasn't amazing, but definitely reasonable.
After the boot loader was unlocked, I unlocked it with the EZ unlock in the Play Store.
I then loaded up Synergy r50 (nightly at the time) and everything seemed improved.
Anyways, I have since then loaded Paranoid Android, CM10, Beans, and Incubus' Jellywiz.
I went to Beans after Synergy, everything was still fine, then I loaded up Jellywiz RLS7 for a day, and it ran extremely warm and I was dropping
a percentage of my battery every 2 minutes. I nandroided back to Beans, and had the overheat and battery drain problem on that too. I wiped everything and went to Synergy (newest nightly, forgot the number) (edit: added the ktoonsez kernel after many FC's) and the problem still exists. I'm also getting horrible cell signal (not 4g, 4g is fine) at my school where it used to be perfectly fine. Anyone know what I could possibly do besides returning it? I already used Odin to go back to the latest non-leaked stock, and it's still doing it. Thank you very much.
TL;DR: After flashing multiple roms, then flashing Jellywiz, my phone runs much too hot for comfort, borderline burning, battery life goes fast, and I get next to no signal at my school.
Thanks again for any help!
Click to expand...
Click to collapse
Did you try to odin back to Stock, get the new OTA and maybe odin the leaked radio on top? I'd give it a try and see how it works out for you 1-2 days. People are reporting better single with the leaked radio. You flashed a lot of stuff in a very short time and you missed the latest official radio from the G7 OTA.
If you still have issues return the phone to VZW. If not DebugFS, EZ Unlock (make sure to use version 1.2 from rootzwiki) and EZ recovery again. Make a clean Nandroid and go back to your favorite ROM.
All the downloads you need can be found in droidstyle's sticky in devel.
BlackBytes said:
Did you try to odin back to Stock, get the new OTA and maybe odin the leaked radio on top? I'd give it a try and see how it works out for you 1-2 days. People are reporting better single with the leaked radio. You flashed a lot of stuff in a very short time and you missed the latest official radio from the G7 OTA.
If you still have issues return the phone to VZW. If not DebugFS, EZ Unlock (make sure to use version 1.2 from rootzwiki) and EZ recovery again. Make a clean Nandroid and go back to your favorite ROM.
All the downloads you need can be found in droidstyle's sticky in devel.
Click to expand...
Click to collapse
Thank you very much! I just finished installing the OTA and I'm about to flash the leaked radio through Odin.
I'll post back in a few days or so in case this doesn't end up working or if any one else is having this issue and doesn't want to post (much like I was until I realized I can't stand the issues I was having)
Hopefully this works, thanks again!
(If anyone else has any other remedies for this, would be nice to post just in case this doesn't work, thank you)
chisandwich said:
Thank you very much! I just finished installing the OTA and I'm about to flash the leaked radio through Odin.
I'll post back in a few days or so in case this doesn't end up working or if any one else is having this issue and doesn't want to post (much like I was until I realized I can't stand the issues I was having)
Hopefully this works, thanks again!
(If anyone else has any other remedies for this, would be nice to post just in case this doesn't work, thank you)
Click to expand...
Click to collapse
you are welcome,
by the way - try to avoid Jelly Bean ROMs like CM10 or AOKP. They all have issues with the RIL and we have to wait for someone to figure out a fix or an official JB TouchWiz leak.
Hi, I can't seem to find my way around this issue. Every time I try to open any camera app, it doesn't allow me and says it's unable to connect. Is there no sure solution to this yet? I tried flashing new cameras through recovery. Nothing works at all. I have tried flashing fixes from several threads on a clean start, different camera apps, clearing caches, clean wiping, and other things I can't even remember at this point with all the frustration. What's up with this?
TW based ROMs work. AOSP seems to not. I lost the thread explaining how to dial the codes into a TW based ROM, but another problem with this for me is, I am extremely confused as to how to do some of the steps explained in that thread (hence why I closed it, looks like that should be the way out for me though?).
Same problem
CZory91 said:
Hi, I can't seem to find my way around this issue. Every time I try to open any camera app, it doesn't allow me and says it's unable to connect. Is there no sure solution to this yet? I tried flashing new cameras through recovery. Nothing works at all. I have tried flashing fixes from several threads on a clean start, different camera apps, clearing caches, clean wiping, and other things I can't even remember at this point with all the frustration. What's up with this?
TW based ROMs work. AOSP seems to not. I lost the thread explaining how to dial the codes into a TW based ROM, but another problem with this for me is, I am extremely confused as to how to do some of the steps explained in that thread (hence why I closed it, looks like that should be the way out for me though?).
Click to expand...
Click to collapse
I am having the same problem you are. I am running paranoid android and cant get the camera / gallery to work. I hope somebody can help. I had it working on Beans rom build 13 but that is TW. I am going to have to bail on pa if there isn't a fix
bmanderle said:
I am having the same problem you are. I am running paranoid android and cant get the camera / gallery to work. I hope somebody can help. I had it working on Beans rom build 13 but that is TW. I am going to have to bail on pa if there isn't a fix
Click to expand...
Click to collapse
It's an AOSP problem based on the firmware of your camera when getting the phone from what I've seen.
http://forum.xda-developers.com/showthread.php?p=37072484#post37072484
Here's the thread I was talking about, however I'm confused about how to go about zipping and unzipping these files. Or even how to get to them to place the files in to begin with considering internal SD card is the only thing that comes up for USB storage. Unless you're supposed to move them in and out from within android.
Would really like a confirm on whether or not this works for the Verizon version, and whether or not it's a different process/if this even works at all, rather not break it fully
Why is this not more of a widespread issue? it seems so crucial that many are having but nobody seems to be talking about it or wanting to find a definite fix for it?
CZory91 said:
Would really like a confirm on whether or not this works for the Verizon version, and whether or not it's a different process/if this even works at all, rather not break it fully
Why is this not more of a widespread issue? it seems so crucial that many are having but nobody seems to be talking about it or wanting to find a definite fix for it?
Click to expand...
Click to collapse
I had the camera problem on MIUI...
Before flashing, I made a backup of my system with CW
I extracted the SlimISP_ZH.bin from my backup and
copied it to my /data directory and it worked fine.
Link: d-h.st/dwx
(I can't post links yet)
maybe... someone post the fix in this forum and make it sticky... lol
Ughhhhhhhhh. This is getting irritating. Going to revive the thread.
I flashed the new firmware (MD3) for this phone. I had everything good and working with CM10... Guess what, borken camera, same issues...
I can't post links yet, but it's in the android development thread with this title:
★ [Rom][I535VRBMD3][4.1.2] Stock Root Odex/Deodex [05/29/13]★
Except... this time I cannot do the simple copy/paste of the bin files this time, why is that?
At this point I just want my VRBLK3 (I think?) firmware back.. Where can I get it to reverse what I just downloaded, in essence?
Also.. What the heck kind of hurdles am I going to have to go through when CM10.1 is complete?.. I don't think I'll be updating my phone past 10.1 at this rate if this continues, really irritating.
CZory91 said:
Ughhhhhhhhh. This is getting irritating. Going to revive the thread.
I flashed the new firmware (MD3) for this phone. I had everything good and working with CM10... Guess what, borken camera, same issues...
I can't post links yet, but it's in the android development thread with this title:
★ [Rom][I535VRBMD3][4.1.2] Stock Root Odex/Deodex [05/29/13]★
Except... this time I cannot do the simple copy/paste of the bin files this time, why is that?
At this point I just want my VRBLK3 (I think?) firmware back.. Where can I get it to reverse what I just downloaded, in essence?
Also.. What the heck kind of hurdles am I going to have to go through when CM10.1 is complete?.. I don't think I'll be updating my phone past 10.1 at this rate if this continues, really irritating.
Click to expand...
Click to collapse
did you flash this after flashing the rom?
http://forum.xda-developers.com/showthread.php?t=1788313
---------- Post added at 04:47 AM ---------- Previous post was at 04:41 AM ----------
dandydon414 said:
did you flash this after flashing the rom?
http://forum.xda-developers.com/showthread.php?t=1788313
Click to expand...
Click to collapse
my advice, odin back to stock (4.1.2), root and install this rom
http://forum.xda-developers.com/showthread.php?t=1788313
has been great for me, no issues whatsoever
dandydon414 said:
did you flash this after flashing the rom?
http://forum.xda-developers.com/showthread.php?t=1788313
---------- Post added at 04:47 AM ---------- Previous post was at 04:41 AM ----------
my advice, odin back to stock (4.1.2), root and install this rom
http://forum.xda-developers.com/showthread.php?t=1788313
has been great for me, no issues whatsoever
Click to expand...
Click to collapse
Yes, that is the post. I also tried MB1 out of curiosity, no dice on either of them. I had a perfectly working CM10. I dun goofed :\.
That was my next step (rerooting, installing that firmware AIO, and then installing CM10). However my question is this, what happens when more firmware comes out? I have to re root and start over again?
If you flashed md3 just flash back mb1 and you will fix that problem. I had the issue. Pulled the firmware from invisiblek for mb1 and back to normal on liquid smooth
Sent from my GT-P5113 using xda premium
bbqsfire said:
If you flashed md3 just flash back mb1 and you will fix that problem. I had the issue. Pulled the firmware from invisiblek for mb1 and back to normal on liquid smooth
Sent from my GT-P5113 using xda premium
Click to expand...
Click to collapse
for some reason I haven't good luck running cm roms on the s3........have much better luck with tw based rom. that's why I recommend a restock and basically start all over from scratch
dandydon414 said:
for some reason I haven't good luck running cm roms on the s3........have much better luck with tw based rom. that's why I recommend a restock and basically start all over from scratch
Click to expand...
Click to collapse
Yeah I think a clean slate is definitely needed from time to time. I swap roms frequently but liquid gives me the best battery life right now from my tests so I keep going back. I Get scared telling people to odin because so mant people soft brick while screwing up a flash inodin or hard brick because they flash a non Verizon rom
Sent from my GT-P5113 using xda premium
bbqsfire said:
Yeah I think a clean slate is definitely needed from time to time. I swap roms frequently but liquid gives me the best battery life right now from my tests so I keep going back. I Get scared telling people to odin because so mant people soft brick while screwing up a flash inodin or hard brick because they flash a non Verizon rom
Sent from my GT-P5113 using xda premium
Click to expand...
Click to collapse
good point. saw where someone flashed an i9300 s3 rom on the verizon s3 and brick city. my problem with aokp, cm, liquid, carbon, baked bean, I've tried them all, is constant freezing forcing me to pull the battery. I love the features of those roms but I hate having to pull the battery all the time
Hmm, over the past couple days I've tried out a few different ROMs on my girlfriend's S3 here, and on each one I would get this "Could not connect to the camera" error, every single time upon opening the camera app. One of the Paranoid Android ROMs, Liquid Smooth, and Synergy (even the Touchwiz camera was broken on that!).
I can restore to the original backup I made of the stock ROM, and the camera works fine again. But as soon as I try a different ROM, no camera.
I'd love to get an AOSP ROM running on this phone, but having a working camera is a requirement, and I can't figure out what I'm doing wrong. Searching the individual threads for the ROMs yields little help, and I'm getting exactly the same error on different ROMS, so I feel like I'm doing something wrong on a higher level. Any chance that switching from TWRP to CWM would make a difference? I don't see why it would, but I suppose it's something I could try.
bbqsfire said:
If you flashed md3 just flash back mb1 and you will fix that problem. I had the issue. Pulled the firmware from invisiblek for mb1 and back to normal on liquid smooth
Sent from my GT-P5113 using xda premium
Click to expand...
Click to collapse
Yep, I'm saying I tried that, still nothing :\ I'm going to flash MB1 and get the stock files again to see if it will do anything but I doubt it.
CZory91 said:
Yep, I'm saying I tried that, still nothing :\ I'm going to flash MB1 and get the stock files again to see if it will do anything but I doubt it.
Click to expand...
Click to collapse
Have you tried odin back to MB1 or even LK3 and letting it go through the OTA's? Those OTA's also update rpm, and other partitions, that as far as I know don't get updated when we flash these stock files on xda unless we flash them ourselves. Maybe something screwed up and is being persistent since those partitions aren't getting updated along the way?
Watanuki-Kun said:
Have you tried odin back to MB1 or even LK3 and letting it go through the OTA's? Those OTA's also update rpm, and other partitions, that as far as I know don't get updated when we flash these stock files on xda unless we flash them ourselves. Maybe something screwed up and is being persistent since those partitions aren't getting updated along the way?
Click to expand...
Click to collapse
I'm honestly just going to restart from scratch and re root when CM10.1 is fully done (hopefully soon...) Nothing is working. Flashed to MB1 firmware on CM 10. Tan MB1 CleanROM. Camera worked in CleanROM, copy/pasted onto my CM10 after the restore, still nothing... Seriously mind boggling.
CZory91 said:
I'm honestly just going to restart from scratch and re root when CM10.1 is fully done (hopefully soon...) Nothing is working. Flashed to MB1 firmware on CM 10. Tan MB1 CleanROM. Camera worked in CleanROM, copy/pasted onto my CM10 after the restore, still nothing... Seriously mind boggling.
Click to expand...
Click to collapse
Probably best, that would be my first thing to try if I had that problem, restarting from scratch. If all else fails, restarting from scratch will wipe out everything. If that failed, I would probably suspect hardware issue.
Watanuki-Kun said:
Have you tried odin back to MB1...
Click to expand...
Click to collapse
Flashing the MB1 firmware fixed the camera for me on AOSP. I flashed this zip in recovery after the ROM was installed:
http://invisiblek.org/sch-i535/firmware/
Link was obtained from here (FAQ about it):
http://rootzwiki.com/topic/34053-firmware-vrbmd3-modemrpmtzsbl-verizon-sgs3-sch-i535/
dandydon414 said:
good point. saw where someone flashed an i9300 s3 rom on the verizon s3 and brick city. my problem with aokp, cm, liquid, carbon, baked bean, I've tried them all, is constant freezing forcing me to pull the battery. I love the features of those roms but I hate having to pull the battery all the time
Click to expand...
Click to collapse
Well I would recommend liquid 2.5 with the kernel that comes with it and I never change any of the overclocking settings. I don't have to pull the battery at all on this one.
Sent from my SCH-I535 using xda premium
TunedReference said:
Flashing the MB1 firmware fixed the camera for me on AOSP. I flashed this zip in recovery after the ROM was installed:
http://invisiblek.org/sch-i535/firmware/
Link was obtained from here (FAQ about it):
http://rootzwiki.com/topic/34053-firmware-vrbmd3-modemrpmtzsbl-verizon-sgs3-sch-i535/
Click to expand...
Click to collapse
Yep, that's what I tried. Nothing.
hey im new to the forum and i rooted my s3 and have the r420 senergy rom installed but the wifi dooesnt work! uhhhhh i cant post in the development section till i have 10 posts. so any one who can help that would be great. ive been doing a lot of reading and what is the differnce between nightly and and regular roms? and i read that the wifi wont work on the nightly rom with out a kernel flash?>?>? Is this right? im going to try the v1.6 senergy any way .....my model is the i535 but yall probably already know that because you hacked my ip address and seen my phone plugged in J/K ha thanks in advance
First off, Synergy r433 is the latest version. And a new release is scheduled to drop any minute now.
A nightly is an experimental build that gets updated nightly. Whereas a stable build is less frequent but as the name suggests is stable. Nightly you must really know what you're doing and are be okay with occasional bugs, otherwise use the stable releases. (fyi SynergyROM stopped releasing nightlies)
As for your Wifi problem, reflash but the make sure you do a full factory reset, and then a super wipe within the AROMA installer. *This will wipe internal storage, make sure to have the ROM zip on external storage* Wifi is not bugged, I'm suggesting the was a flashing error.
Sent via SGS3 using Tapatalk
Thank you so much for replying. i was thinking the same about the nightly "name" but thanks for clarifying. i have tried several times. in clockworkmod recovery(or whatever the name is) i factory reset and in the installer i wipe everything. (on the internal sd) and then install cleanly. but my kernel doesnt flashed it says its not unlocked.?!?! how do i unock it? i unlocked the bootloader and once more so i knew for sure. and my phone says custom with a padlock unlocked symbol below. but same thing everytime...wifi is buggy. i like this rom and just want it to work...thanks!!!!!!!!!!!!! is there a special "better" kernel unlock method? my paitients are getting low...lol well my girl wants her phone stock ...F**CK THATT!!!!!!!!!! thanks man
Bump please someone plesase help.. I need this phone working asap
Check out this link
seems to work for some.
http://forum.xda-developers.com/showthread.php?p=40531554
Mine has always been good.
I also use an app called Opensignal
https://play.google.com/store/apps/details?id=com.staircase3.opensignal
When on the OpenSignal app select > wifi then select the > refresh then the > refresh network.
I do this every week or so. I have no issues with wifi, ever.
Some say tightening the screws
help check out rhe link below
http://gs3.wonderhowto.com/how-to/s...-gps-problems-your-samsung-galaxy-s3-0145332/
I hear it's just some phones. Anyways
good luck
Sent from my Smoking smooth
Synergy r484
Mods by gunthermic,
Theme by jbeitel
I am experiencing the same issue.
I rooted, flashed CWO, and then installed synergy. Nothing worked... then I read that you need to unlock the bootrom so I did that, rebooted and got the same... no wifi. After unlocking the bootloader I reinstalled synergy (R484) and still WiFi will not turn on.
I followed they synergy thread for flashing and This thread for bootloader unlocks.
Provider: Verizon
Phone: GS3
ROM: SynergyROM (r484)
Recovery: ClockworkOrange
Got it fixed!
So... I only used odin... no romloader apps or any of that crap...
1: Reinstalled stock ROM
2: Reinstalled CWO
3: Reinstalled Root+Bootloader
4: Reinstalled SynergyROM
5: Enjoy! Wifi works, all applications work!
Chris
Alrighty, this is one of the weirdest things I've had happen with a phone since I started doing this on the original Droid. Lately I've been using Jellybeans Rom, its been great and my longest running ROM so far, but like a lot of people here I have to try out new stuff quite often just to try it. Well anymore I cant seem to try much else, I wanted to run the newest Liquid Smooth 2.3 ROM that just hit and it wont work at all really, before I redid the whole phone every time I flashed LS 2.3 I couldnt even hit the start button when the ROM first installed, when I did it wouldnt do anything and then the screen would go black and I would have to hard reset or battery pull. Next boot up seemed to go fine, got my gmail up and running and titanium downloaded and then after that, hitting settings options would lock up the phone in just about any app I had, never even got around to trying to restore anything with titanium.
Re-flashed LS 2.3 three or four times and nothing changed, tried fixing permissions, fully wiping, etc. didnt matter. So naturally I figured it was simply the ROM on my phone (mind you LS 2.2 worked fine before) so I went and decided I would try out Avatar ROM, CM based with MIUI themes, this ROM did pretty much the same thing. No idea why...
Next I figured something maybe was wrong with my phone so I went back to the drawing board and started from factory with ODIN, I redid my ROM with stock/root, unlocked the boot loader again and redid custom recovery and all the same thing with LS 2.3 happened all over again, Stock ROM worked great for the bit of time I used it before I tried to reflash LS 2.3 again, Now I'm back running Jellybeans v.15 and it runs perfectly fine as well.
I really have no idea what the problem is, both of those ROMs I've tried are CM based original development, so I'm wondering if its something in there thats causing an issue over the TW ROMs I've used. I've used other TW ROMs with decent success, but I've had some issues with those too that you wouldnt think should happen but it wasnt anything worth noting, just like Jellybeans the best, but even some of those would give me slow down problems and occasional lock ups when Jellybeans doesnt.
Anyone have any clue as to what could be causing this? I used to be able to run non TW roms just fine and its only been in the past month that this has started happening that I've noticed, I've had the phone since January and have been flashing away this whole time and now I cant seem to try out any more ROMs without having major issues......ugh
Your situation is a very random situation but I have something similar happened to me involving TW ROMs in that some of them froze on me. I had to flash the stock ROM.
Bump, anyone having any kind of similar problems?
Sent from my SCH-I535 using xda premium
Vidfreek said:
Bump, anyone having any kind of similar problems?
Sent from my SCH-I535 using xda premium
Click to expand...
Click to collapse
If you've only had these issues in the last month, it could be attributed to the Linux 3.4 kernel that every AOSP rom has moved to. I wouldn't let that stop you though. Are you downloading these rom zips over WiFi or mobile data? Were your downloads taking awhile as well? I know either GOO or AFH was having server issues recently which may have coincided with your downloads. I'd suggest using WiFi if you aren't already and trying again?
Sent from my SCH-I535 using xda app-developers app
Yeah its only been fairly recent and all roms I've tried have been updated since the very end of april, if my phone has major problems with that linux kernal am I going to be able to flash anything again? Everything I downloaded was over wifi but I can try all the downloads again but I'm thinking that won't fix anything, just weird stuff
Sent from my SCH-I535 using xda premium
I have installed 4.2.2 version of LiquidSmooth. But after installing it my network is dropping out within a min of talking. It's so annoying as I missed the most importing function. Talking to others using my phone.
ravi.kalyan said:
I have installed 4.2.2 version of LiquidSmooth. But after installing it my network is dropping out within a min of talking. It's so annoying as I missed the most importing function. Talking to others using my phone.
Click to expand...
Click to collapse
What radio are you using? You should be using UCMC1.
Sent from my SAMSUNG-SGH-I727 using xda premium
I have a similar issue. I've been running the March 23rd version of AoKp with no problems. However, I recently tried to install the latest version and my phone will not connect to the Rogers network (connects briefly during start up, then drops, this trend repeats infinitely). Even when I do get some bars of connectivity, it never actually registers with the network, so I cannot send/receive calls, sms, etc. All other functions work fine. Also of note; after first reboot after installing ROMs, all the correct APN's are there and it seems to default to Rogers LTE which is good, however never actually connects. Then, after a subsequent reboot, all APN's are missing and I cannot manually add any (when I save them, they don't actually save).
I've tried installing the latest version of CM - same issue
Tried flashing different radios to no avail (running UCMC1 currently)
Luckily I'm always able to restore my backup to that March 23rd version AoKp which still works without issue. My next step is to revert back to stock ROM and either stick with that or try installing a fresh custom following that.
Any idea what the issue is???
I'm seeing the same issue as well on AT&T.
I tried reverting back to the regular Cyanogenmod Rom, but I'm seeing the issue where the radio keeps dropping and connecting back every few seconds.
I'm on baseband UCLI3. Is that the best version to use?
LamboJ said:
I'm seeing the same issue as well on AT&T.
I tried reverting back to the regular Cyanogenmod Rom, but I'm seeing the issue where the radio keeps dropping and connecting back every few seconds.
I'm on baseband UCLI3. Is that the best version to use?
Click to expand...
Click to collapse
You need to be on ucmc1 for cm 10.1
Sent from my SAMSUNG-SGH-I727 using xda app-developers app