Hey guys i do have a bit of experience flashinng roms and custom recoveries but im stuck on this one. My asus me301t memo pad is coming on then the asus screen stays on for about 15 seconds then turns on and off randomly about every 5-10 seconds. Ive never bootlooped anything yet so im not sure if that is what is going on here or not. I did unlock it with the asus unlock tool and fastboot twrp then flashed a cm mod 11. I know that was risky but if i can flash skyrocket roms to my rogers SII i thought maybe these ttwo tablets are close enough to do the same. What has me confused is after a week of fighting to get it back with only apx mode to work with i broke down and changed the main board. It acts the exact same way with the new board! What else should i look at? Could i have fried another part that is causeing it? I.ve unlocked, rooted, and flashed rom to about 10 tf101's and 5 tf300t's in the last 2 weeks but this me301t is a real tough one for me.
lljeffll said:
Hey guys i do have a bit of experience flashinng roms and custom recoveries but im stuck on this one. My asus me301t memo pad is coming on then the asus screen stays on for about 15 seconds then turns on and off randomly about every 5-10 seconds. Ive never bootlooped anything yet so im not sure if that is what is going on here or not. I did unlock it with the asus unlock tool and fastboot twrp then flashed a cm mod 11. I know that was risky but if i can flash skyrocket roms to my rogers SII i thought maybe these ttwo tablets are close enough to do the same. What has me confused is after a week of fighting to get it back with only apx mode to work with i broke down and changed the main board. It acts the exact same way with the new board! What else should i look at? Could i have fried another part that is causeing it? I.ve unlocked, rooted, and flashed rom to about 10 tf101's and 5 tf300t's in the last 2 weeks but this me301t is a real tough one for me.
Click to expand...
Click to collapse
Sure, sounds like the perfect boot-loop: starting the kernel crashes and causes a reboot, etc.
Usually you can get out of the boot-loop by holding volume-down and wait for the next reboot. That should give you the bootloader screen and you can fastboot a new boot image or go to recovery and reflash your ROM from there.
If it won't work right away, there are lots of variations to try suggested in several threads: for example combine it with a reset or switch it off and plug in the charger. Well, those are for TF300T, but i guess your ME301T is not that different in that respect.
Sent from my TF300T using Tapatalk
f69m said:
Sure, sounds like the perfect boot-loop: starting the kernel crashes and causes a reboot, etc.
Usually you can get out of the boot-loop by holding volume-down and wait for the next reboot. That should give you the bootloader screen and you can fastboot a new boot image or go to recovery and reflash your ROM from there.
If it won't work right away, there are lots of variations to try suggested in several threads: for example combine it with a reset or switch it off and plug in the charger. Well, those are for TF300T, but i guess your ME301T is not that different in that respect.
Sent from my TF300T using Tapatalk
Click to expand...
Click to collapse
Hmmm, funny ive been rooting aand flashing roms for 6 months or more and didnt know or figure out to just hold the one volume button. Turns out that the used board that i put in was also in bootloop! What are the chances? so i borrowed one out of a working one i have and it worked. Thx for your response. The volume down button option might save me a lot of headake next time. in fact i think ill put it back in and give it a try. Thx
lljeffll said:
Hmmm, funny ive been rooting aand flashing roms for 6 months or more and didnt know or figure out to just hold the one volume button. Turns out that the used board that i put in was also in bootloop! What are the chances? so i borrowed one out of a working one i have and it worked. Thx for your response. The volume down button option might save me a lot of headake next time. in fact i think ill put it back in and give it a try. Thx
Click to expand...
Click to collapse
Well that didnt work. Unless you have to press and release at a spacific time. Tried a few different ways and it didnt effect thee tablet at all.
lljeffll said:
Well that didnt work. Unless you have to press and release at a spacific time. Tried a few different ways and it didnt effect thee tablet at all.
Click to expand...
Click to collapse
Did you try the small reset hole? Usually people suggest to use a paperclip to go in, but at least German paperclips are too thick; I had a hard time finding something to go in. But might help you.
You'll have to figure out, where it is on your device. Don't confuse it with the microphone.
Then press in, till you feel the switch giving way, but don't press too hard. Hold for a while (why not a full minute). Then try vol-down right away.
Sent from my TF300T using Tapatalk
f69m said:
Did you try the small reset hole? Usually people suggest to use a paperclip to go in, but at least German paperclips are too thick; I had a hard time finding something to go in. But might help you.
You'll have to figure out, where it is on your device. Don't confuse it with the microphone.
Then press in, till you feel the switch giving way, but don't press too hard. Hold for a while (why not a full minute). Then try vol-down right away.
Sent from my TF300T using Tapatalk
Click to expand...
Click to collapse
so i put in a new board and flashed some more roms. in the end this tablet cost me nothing but im enjoying the challange its causing so im gonna keep messing with it. What would cause it to bootloop after the asus logo then a min into the rom logo? i still have recovery but no matter what rom i flash it never goes past a min into the rom logo
lljeffll said:
so i put in a new board and flashed some more roms. in the end this tablet cost me nothing but im enjoying the challange its causing so im gonna keep messing with it. What would cause it to bootloop after the asus logo then a min into the rom logo? i still have recovery but no matter what rom i flash it never goes past a min into the rom logo
Click to expand...
Click to collapse
If you still got recovery, let it loop, then go to recovery. Then check the file /proc/last_kmsg.
It has the kernel log from your last bootloop. You should be able to find some hints there.
Sent from my TF300T using Tapatalk
f69m said:
If you still got recovery, let it loop, then go to recovery. Then check the file /proc/last_kmsg.
It has the kernel log from your last bootloop. You should be able to find some hints there.
Sent from my TF300T using Tapatalk
Click to expand...
Click to collapse
i got it going again but when i flash the omni rom 4.4 which they say i can on the me301 i have a mouse pointer as if im a tf300t on keyboard but controlled with touch screen and also in settings i am listed as a tf300t. lol.ive really confused this poor machine. Any ideas on this?
lljeffll said:
i got it going again but when i flash the omni rom 4.4 which they say i can on the me301 i have a mouse pointer as if im a tf300t on keyboard but controlled with touch screen and also in settings i am listed as a tf300t. lol.ive really confused this poor machine. Any ideas on this?
Click to expand...
Click to collapse
Did you flash the OmniROM for ME301T? There is a separate build and a separate thread.
Sorry, lacking a ME301T myself, so only got this pointer for you.
Sent from my TF300T using Tapatalk
f69m said:
Did you flash the OmniROM for ME301T? There is a separate build and a separate thread.
Sorry, lacking a ME301T myself, so only got this pointer for you.
Sent from my TF300T using Tapatalk
Click to expand...
Click to collapse
good idea! thx. I prob got the one for the tf300t and when it flashed the kernal.... I have the tf300t aswell so i likely have a copy for that. Its a much better tablet but id like to get this one to 4.4 too. Funny tho, i got a mouse hooked up with an otg cable from my samsung s2 and its not kinda cool. the round pointer dissapeared after about 10 min for whatever reason idk and left me with a nice little pointer. i might end up keeping it this way if i cant get a good 4.4 rom to work properly.
Thank you so much f69m.
I thought i had the right rom and such but I went looking and found what was looking for right here on xda ofcourse. The kitkat compatability pack! Got cm 11 nightly running right now! Not sure if everything works right yet but so far so good.
Related
Hello all, I just recently bought a tf300t, unlocked it, installed cwm 5.5.0.4 for ics, and then updated to jellybean hydro, then installed cwm 6.
Afterwards, just recently noticed that CM 10 nightlies came out, so i updated to it. I went through step by step, and DID NOT USE rom manager. I went into straight recovery mode. It installed perfectly fine, but when i reboot, it would get stuck at the initial asus splash screen. At first I was able to get into RCK. I became extremely upset, fell asleep and the device eventually died, because it wouldn't turn off, it would constantly boot loop. The next morning, I plugged it in, and it would not even get into RCK, but it would show the options for fastboot, RCK, and cold boot. So, just to restate. Was able to get into RCK, device died, then would not boot into RCK. So then I ran fastboot, and that completely stopped the device from showing ANY options when holding power + volume down. I can not get to RCK or fastboot.
So all in all my device is legitimately stuck at the initial asus boot screen, and NOTHING happens when I hold power + volume down.
Anybody got some ideas? I'm going to japan soon, i'll try and stay in touch. Someone on the forums named Neroga will keep this updated for me while I'm in transit, i'm military and ridiculously busy.
thanks all
just flash stock ROM with fastboot. this should work.
I've tried multiple times. No menu pops up with power + volume down. Literally just hangs on the unlocked screen. I can put it in APX mode or whatever it's called but I heard that nvflash isn't working for the tf300, yet.
Sent from my Motorola Atrix 4G
Blubberor said:
just flash stock ROM with fastboot. this should work.
Click to expand...
Click to collapse
Neroga said:
I've tried multiple times. No menu pops up with power + volume down. Literally just hangs on the unlocked screen. I can put it in APX mode or whatever it's called but I heard that nvflash isn't working for the tf300, yet.
Sent from my Motorola Atrix 4G
Click to expand...
Click to collapse
What neroga said, we can't get to the menu to choose fastboot.
Velict said:
What neroga said, we can't get to the menu to choose fastboot.
Click to expand...
Click to collapse
I asked our friends at androidroot.mobi if it would be possible to have this issue solved with NVFLASH, this is their response:
@AndroidRootMobi Is it worth waiting for NVFLASH on (very hard) softbricked TF300t? Or should I go to @Asus
@AndroidRootMobi
@Joanuz @ASUS Sorry. If/when we support TF300T, you will need device-specific files. So no brick recovery if you're already bricked.
It sucks, I know. I'll be sending mine back to ASUS tomorrow. No warranty. Hopefully a reflash will do the job (normally it should be around 75 euro), if the mainboard needs to be replaced, the total costs will be around 200... I will open a thread here once it's under repair. Good luck! (and PLEASE don't come up with a solution while mine is in repair :laugh:
Sphinix said:
I asked our friends at androidroot.mobi if it would be possible to have this issue solved with NVFLASH, this is their response:
@AndroidRootMobi Is it worth waiting for NVFLASH on (very hard) softbricked TF300t? Or should I go to @Asus
@AndroidRootMobi
@Joanuz @ASUS Sorry. If/when we support TF300T, you will need device-specific files. So no brick recovery if you're already bricked.
It sucks, I know. I'll be sending mine back to ASUS tomorrow. No warranty. Hopefully a reflash will do the job (normally it should be around 75 euro), if the mainboard needs to be replaced, the total costs will be around 200... I will open a thread here once it's under repair. Good luck! (and PLEASE don't come up with a solution while mine is in repair :laugh:
Click to expand...
Click to collapse
I think it really depends on where the tablet is shipped for RMA because mine got reflashed for free I didn't even have to pay shipping or diagnostic costs.
sparky28000 said:
I think it really depends on where the tablet is shipped for RMA because mine got reflashed for free I didn't even have to pay shipping or diagnostic costs.
Click to expand...
Click to collapse
Wow, that's great. I think they might notice the "bootloader unlocked" in the top right corner though... Anyway: I don't really mind paying, it's like paying for a lesson learned
Mine is going to the Czech Republic. Where did yours go to?
Sphinix said:
Wow, that's great. I think they might notice the "bootloader unlocked" in the top right corner though... Anyway: I don't really mind paying, it's like paying for a lesson learned
Mine is going to the Czech Republic. Where did yours go to?
Click to expand...
Click to collapse
Czech Republic also and mine was obviously unlocked. With some luck they will just perform a "BIOS upgrade" and repair it for free. Did take them about 3 weeks though. And if it makes any difference I did lie about bricking it myself. I told them that the official update went wrong and bricked my device.
I'm stucked at Asus logo but I can go into recovery and fastbood. There is something that I can do to repair my tablet?
Sphinix said:
I asked our friends at androidroot.mobi if it would be possible to have this issue solved with NVFLASH, this is their response:
@AndroidRootMobi Is it worth waiting for NVFLASH on (very hard) softbricked TF300t? Or should I go to @Asus
@AndroidRootMobi
@Joanuz @ASUS Sorry. If/when we support TF300T, you will need device-specific files. So no brick recovery if you're already bricked.
It sucks, I know. I'll be sending mine back to ASUS tomorrow. No warranty. Hopefully a reflash will do the job (normally it should be around 75 euro), if the mainboard needs to be replaced, the total costs will be around 200... I will open a thread here once it's under repair. Good luck! (and PLEASE don't come up with a solution while mine is in repair :laugh:
Click to expand...
Click to collapse
I knew NVFLASH wasn't going to work, since you basically need to backup your device with it, then you'll be unbrickable. The whole point of NVFLASH is BEFORE you decide to mess with your tablet, you make sure you have a failsafe, which is NVFLASH. Since the whole tablet is completely locked out, it won't work. Idont understand why asus would make a device that completely locks itself out. Even on a normal everyday computer, the bios can be completely reinstalled.
Why can't firmware?
I just sent the tf300t in for RMA. UPS $27 USD for shipping. I"ll keep everyone updated along with whoever else probably has threads like this open, especially for theTF300t
For anyone who comes across this thread, let me recap on what you should do if you have a TF300t, or tf700. DO NOT go to jellybean yet. I honestly suggest waiting for CM10 nightly to become more stable. Also, wait for nvflash for these devices. With that tool you'll become unbrickable.
Velict said:
I just sent the tf300t in for RMA. UPS $27 USD for shipping. I"ll keep everyone updated along with whoever else probably has threads like this open, especially for theTF300t
For anyone who comes across this thread, let me recap on what you should do if you have a TF300t, or tf700. DO NOT go to jellybean yet. I honestly suggest waiting for CM10 nightly to become more stable. Also, wait for nvflash for these devices. With that tool you'll become unbrickable.
Click to expand...
Click to collapse
Is there any way to stop the JB update notification? I set the postpone to one day but it keeps popping up all the time!
Velict said:
I just sent the tf300t in for RMA. UPS $27 USD for shipping. I"ll keep everyone updated along with whoever else probably has threads like this open, especially for theTF300t
For anyone who comes across this thread, let me recap on what you should do if you have a TF300t, or tf700. DO NOT go to jellybean yet. I honestly suggest waiting for CM10 nightly to become more stable. Also, wait for nvflash for these devices. With that tool you'll become unbrickable.
Click to expand...
Click to collapse
That's a good advice/warning , considering that the Jelly Bean bootloader is completely incompatible with CM9/CM10/AOKP and all derivatives that are designed around the ICS kernel. Hope they find a solution for those who already jumped on the Asus JB train.
Skickat från min Transformer Pad TF300T
solefero69 said:
I'm stucked at Asus logo but I can go into recovery and fastbood. There is something that I can do to repair my tablet?
Click to expand...
Click to collapse
I am having the same problem and the whole thing is so confusing that I am loosing hope to get my Transformer tf300gt working again, Did you managed to have yours sorted out.
Regards,
Yves
I had this happen once, but continuously pressing Vol- & Power got me into bootloader eventualy. It took "forever" for my feeling, may be 20-30 seconds, but it booted to the bootloader.
Ti2 said:
I had this happen once, but continuously pressing Vol- & Power got me into bootloader eventualy. It took "forever" for my feeling, may be 20-30 seconds, but it booted to the bootloader.
Click to expand...
Click to collapse
I just went through a brick scenario when trying to get data2sd working with cleanrom 3.3 after many bootloops i was able to install the stock rom. I am going to unlock and reinstall cleanrombut first going to back it with nvflash. I hate the feeling ofnot knowing if the tablet will stay a brick or not.
Hi there xda-community!
I'm a little bit shocked - It seems I managed to break my Asus TF300t while trying to install Cyanogenmod (latest version).
I followed the guide in the wiki "Asus_Transformer_Pad_TF300T:_Full_Update_Guide"
And I'm already at the last step where you should reboot your tablet but I'm stuck on the Asus-Booting Screen. I can't even turn the tablet off. (Automatically reboots)
It says in the top left corner "The Device is UnLocked." followed by a large ASUS-Logo in the middle and a small NVIDIA TEGRA logo in the lower right corner.
I'm still able to go into the recovery and already tried to install the ROM again. But I'm still stuck at the loading screen.
I'm not an expert on this topic but still thought I would be able to install CM - but right now I have no idea what to do next. I don't even know how to turn my pad off.
I would greatly appreciate any help!
Nijin said:
Hi there xda-community!
I'm a little bit shocked - It seems I managed to break my Asus TF300t while trying to install Cyanogenmod (latest version).
I followed the guide in the wiki "Asus_Transformer_Pad_TF300T:_Full_Update_Guide"
And I'm already at the last step where you should reboot your tablet but I'm stuck on the Asus-Booting Screen. I can't even turn the tablet off. (Automatically reboots)
It says in the top left corner "The Device is UnLocked." followed by a large ASUS-Logo in the middle and a small NVIDIA TEGRA logo in the lower right corner.
I'm still able to go into the recovery and already tried to install the ROM again. But I'm still stuck at the loading screen.
I'm not an expert on this topic but still thought I would be able to install CM - but right now I have no idea what to do next. I don't even know how to turn my pad off.
I would greatly appreciate any help!
Click to expand...
Click to collapse
More info needed. What version of recovery are you using? The last time you successfully booted, were you on ICS or jb? What version of cm are you trying to flash?
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
funnel71 said:
More info needed. What version of recovery are you using? The last time you successfully booted, were you on ICS or jb? What version of cm are you trying to flash?
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
Click to expand...
Click to collapse
My guess, as many went before him: Official JB update, adepted bootloader and then... A wipe.
The end! All you can do now is ship it to ASUS to have it fixed. I had mine back yesterday, they fixed it under warranty within one week. But this is Europe, I've read different (horror ) stories here, ranging from tablet in RMA for more than 1.5 month, up to replacing the mainboard (charging a total of 200 dollar).
If you are in Europe, ship it back, lie, say it's stuck after JB upgrade, they will fix it (fast!).
Good luck!
funnel71 said:
More info needed. What version of recovery are you using? The last time you successfully booted, were you on ICS or jb? What version of cm are you trying to flash?
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
Click to expand...
Click to collapse
Hi funnel, thanks for your help - sorry for missing the Infos.
I'm using "CWM-based Recovery v6.0.1.3" (showthread.php?t=1668173). Last time I booted the stock JellyBean Firmware. I'm trying to flash "cm-10-20120920-NIGHTLY-tf300t.zip"
Sphinix said:
My guess, as many went before him: Official JB update, adepted bootloader and then... A wipe.
The end! All you can do now is ship it to ASUS to have it fixed. I had mine back yesterday, they fixed it under warranty within one week. But this is Europe, I've read different (horror ) stories here, ranging from tablet in RMA for more than 1.5 month, up to replacing the mainboard (charging a total of 200 dollar).
If you are in Europe, ship it back, lie, say it's stuck after JB upgrade, they will fix it (fast!).
Good luck!
Click to expand...
Click to collapse
Oh.. this doesn't sound good. What would be the way I should have taken?
I did now flash (after a full wipe + cache wipe) the official firmware (from ASUS Website).
THIS DID WORK!!!
I am now back with my pad on the official ROM. (With an unlocked bootloader - but otherwise like it was when I bought it.)
This fixed my problem but I'm still wondering where I went wrong... Could someone explain me what I did wrong and how do prevent it next time?
Thanks for your help!
Nijin said:
Hi funnel, thanks for your help - sorry for missing the Infos.
I'm using "CWM-based Recovery v6.0.1.3" (showthread.php?t=1668173). Last time I booted the stock JellyBean Firmware. I'm trying to flash "cm-10-20120920-NIGHTLY-tf300t.zip"
Oh.. this doesn't sound good. What would be the way I should have taken?
I did now flash (after a full wipe + cache wipe) the official firmware (from ASUS Website).
THIS DID WORK!!!
I am now back with my pad on the official ROM. (With an unlocked bootloader - but otherwise like it was when I bought it.)
This fixed my problem but I'm still wondering where I went wrong... Could someone explain me what I did wrong and how do prevent it next time?
Thanks for your help!
Click to expand...
Click to collapse
CM10 currently doesn't work with the JB bootloader (which you have since updating) as far as I'm aware, which would probably explain why it went wrong.
Check out Hydro or CleanROM perhaps, both have been updated for new JB bootloader.
mozyman said:
CM10 currently doesn't work with the JB bootloader (which you have since updating) as far as I'm aware, which would probably explain why it went wrong.
Check out Hydro or CleanROM perhaps, both have been updated for new JB bootloader.
Click to expand...
Click to collapse
Ah okay - thanks for the info. I'm now running Hydro ROM and I am very happy with it!
In case someone finds this topic and would like to know which firmware I used to get it back again - it was "ASUS Transformer Pad TF300T Firmware: V10.4.2.13 "
Nijin said:
Ah okay - thanks for the info. I'm now running Hydro ROM and I am very happy with it!
In case someone finds this topic and would like to know which firmware I used to get it back again - it was "ASUS Transformer Pad TF300T Firmware: V10.4.2.13 "
Click to expand...
Click to collapse
Any chance you could give me the steps? My stock TF300T is stuck on the boot-logo now.
I never had a chance to even put a single app on it, just turned it on and let it download JB when I went to work, came home tried to install and BRICK. Can I follow your steps if my bootloader is not unlocked?
Sorry for noob questions but I was so excited for my first tablet and now it's dead, I feel like a kid again when I found out Santa wasn't real
TF300T said:
Any chance you could give me the steps? My stock TF300T is stuck on the boot-logo now.
I never had a chance to even put a single app on it, just turned it on and let it download JB when I went to work, came home tried to install and BRICK. Can I follow your steps if my bootloader is not unlocked?
Sorry for noob questions but I was so excited for my first tablet and now it's dead, I feel like a kid again when I found out Santa wasn't real
Click to expand...
Click to collapse
I'm afraid that you will not be able to follow my steps because I used the CW Recovery. (This can only be installed with an unlocked bootloader (as far as I know)).
But since your bootloader is not unlocked you still have your warranty. I'd suggest to call the ASUS Support Hotline / Mail them and ask if they can help you. In worst case scenario you will have to send them your tablet but should get in repaired for free.
Yeah, ASUS will RMA but I have to pay shipping >.<
Trying to get supplier to just send me a new one, heres to hoping!
TF300T said:
Yeah, ASUS will RMA but I have to pay shipping >.<
Trying to get supplier to just send me a new one, heres to hoping!
Click to expand...
Click to collapse
I don't know if this was mentioned but have you tried to wipe data first? Just a though
T.
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
funnel71 said:
I don't know if this was mentioned but have you tried to wipe data first? Just a though
T.
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
Click to expand...
Click to collapse
1. Hold the Power button in for about 5-7 seconds to get it to reboot. (Seems stupid for the device to auto restart, wish I could change that.)
2. After the screen goes black, hold the Power and the Volume Down buttons until you get the words in the upper left corner to say something about hitting the Volume Up to load Recovery (don't hit the volume up, there's no recovery on an locked bootloader).
3. Hit the Volume Down button unless the "Wipe Data" icon is highlighted and then hit the Volume Up to confirm. This will go through the factory reset option and should bring your tablet back to working condition if it's possible.
* if you get the android laying on his back you tried to boot the recovery partition after step 2, just start over and hold the power button down to reset the device and remember do NOT hit the Volume Up button after it restarts until you have hit the Volume Down button to highlight the Wipe Data icon.
Let us know if this works.
-Nate
herschwolf said:
1. Hold the Power button in for about 5-7 seconds to get it to reboot. (Seems stupid for the device to auto restart, wish I could change that.)
2. After the screen goes black, hold the Power and the Volume Down buttons until you get the words in the upper left corner to say something about hitting the Volume Up to load Recovery (don't hit the volume up, there's no recovery on an locked bootloader).
3. Hit the Volume Down button unless the "Wipe Data" icon is highlighted and then hit the Volume Up to confirm. This will go through the factory reset option and should bring your tablet back to working condition if it's possible.
* if you get the android laying on his back you tried to boot the recovery partition after step 2, just start over and hold the power button down to reset the device and remember do NOT hit the Volume Up button after it restarts until you have hit the Volume Down button to highlight the Wipe Data icon.
Let us know if this works.
-Nate
Click to expand...
Click to collapse
I had the same problem trying to install CM10 with the JB bootloader. As soon as you restart after its installed it hangs at the ASUS logo.
I tried wiping everything but my backup and still had no luck. Thanks for this procedure though. I was really scared I bricked it for a bit there. Was especially scared at the thought that I live in the US and would never get lucky enough to have mine replaced under warranty.
So yes I can confirm your procedure will correct the issue.
k4killer said:
I had the same problem trying to install CM10 with the JB bootloader. As soon as you restart after its installed it hangs at the ASUS logo.
I tried wiping everything but my backup and still had no luck. Thanks for this procedure though. I was really scared I bricked it for a bit there. Was especially scared at the thought that I live in the US and would never get lucky enough to have mine replaced under warranty.
So yes I can confirm your procedure will correct the issue.
Click to expand...
Click to collapse
im using CleanROM 2.1 at scottsroms .com
with TWiRP 2.2 ( advice to all CWM users, i was one too, uninstall, install TWRP, TEAM WIN RECOVERY PARTITION)
RUNS smooth..
launcher choice: apex or asus stock
its great...
k4killer said:
I had the same problem trying to install CM10 with the JB bootloader. As soon as you restart after its installed it hangs at the ASUS logo.
I tried wiping everything but my backup and still had no luck. Thanks for this procedure though. I was really scared I bricked it for a bit there. Was especially scared at the thought that I live in the US and would never get lucky enough to have mine replaced under warranty.
So yes I can confirm your procedure will correct the issue.
Click to expand...
Click to collapse
CM10 will not work with the JB Bootloader unfortunately. The bootloader will hang at the ASUS logo because of it. Hopefully there will be some development to correct this issue or a CM10 port into the JB bootloader soon, but until then you have the Stock (which has been rooted), Hydro's ROM, and Scott's CleanROM - which I use and love. It's very minimalistic and easy to install.
-Nate
Hi all,
Firstly apologies if this is posted in the wrong place......
I think I might have messed up my Transformer infinity but hoping to see some light at the tunnel.
When I got my tablet I rooted it and unlocked the bootloader (wish I hadn't done that). All of that went fine and I got it all set-up perfectly. I then tried to use CWM to make a back-up of the ROM which didn't work. I read a little online and got the impression that CWM doesn't work as it does with most android devices and then read about being able to get to recovery mode (where I assumed I could make a back-up) using an app called Transformer Pad Recovery Tool so I ran this......BOOM!!!!
My Infinity will now not boot and I have the following....
Normal Boot
Sticks at the first Asus Logo with the white 'Device is Unlocked' text
Powering on with Power & Vol DOWN pressed.
Hangs on the Asus logo with.......
'Android cardu-user bootloader <2.10e> released by "US_epad-9.4.5.30-20120907" A03
Checking for android ota recovery
Booting recovery kernal image
but it doesn't do anything further
Powering on with Power & Vol UP pressed
Tablet goes black screen but windows picks it up as an APX device whereas before it wouldn't pick it up at all. I also have it listed in device manager as 'Asus Transformer TF700 APX interface'
I'm guessing that the APX connection is my only potential route to salvation but I don't know where to go from here. I can't seem access fastboot on the tablet itself and am I right in thinking I can't push anything to it through the PC without this?
- I've read about NVflash but apparently this only works if already on the device before it's KO'd? (I wish I'd have read this article before the recovery app one)
- I've also read somewhere that I can copy the stock blob file to an sd card and then reboot the tablet it will recover from there but it doesn't seem to work (I've tried it with both the blob & meta inf folder and with the zip file)
I'm really worried becuase I can't return it now and I may have messed up big time. I've been reading loads online but can't find a specific answer for my dilema and I'm trying to avoid experimenting too much in case I make things worse.
Can anyone help point me in the right direction?
Thanks
I am sorry mate but it looks like your device it's stuck in the so called "recovery boot loop" and this happened mostly because you have used that app, wich btw was already known for causing bricks and you can find more than one thread warning about it. AFAIK there's no fix for that yet, at least not without NvFlash so it seems that the only way to fix it is sending the device to Asus and pay for the repairs (some users said they paid 250$ for this).
ahh crap. Getting a warranty repair could be fun as well because I'm in the UK using a US model and they haven't even released here. Is it the sort of thing where a solution might come out in the near future or would that just be wishful thinking?
BTW - Edit: The app was called 'Transformer reboot to recovery so everyone steer clear of that as well
It's strange how that app works for some (I can use it without problem) and causes others to get in this "recovery bootloop"... I just don't understand that...
Man, it really sucks that you didn't install NVFlash.
So there is nothing that he can do even though APX mode is working? When I last read of this problem, I thought that the person couldn't even get APX mode working.
Sent from my ASUS Transformer Pad TF700T using Tapatalk 2
jtrosky said:
It's strange how that app works for some (I can use it without problem) and causes others to get in this "recovery bootloop"... I just don't understand that...
Man, it really sucks that you didn't install NVFlash.
So there is nothing that he can do even though APX mode is working? When I last read of this problem, I thought that the person couldn't even get APX mode working.
Sent from my ASUS Transformer Pad TF700T using Tapatalk 2
Click to expand...
Click to collapse
Sadly the APX mode is useless for users without working NvFlash,so considering that OP is on .30 bootloader and didn't used the nvflash tool to backup the needed files, then for him Asus is the only solution, at least for now.
cwm works fine on the infinity. my guess is you were using rom manager which does NOT work on the infinity.
there are several guides posted here to walk people through the recovery/backup process.
I would suggest reading through all of them to see if there is anything you can try.
did you even install cwm through fastboot before running these apps?
DNO1978 said:
ahh crap. Getting a warranty repair could be fun as well because I'm in the UK using a US model and they haven't even released here. Is it the sort of thing where a solution might come out in the near future or would that just be wishful thinking?
BTW - Edit: The app was called 'Transformer reboot to recovery so everyone steer clear of that as well
Click to expand...
Click to collapse
Of course they have been released here... they were released around 3 weeks ago.
hshah said:
Of course they have been released here... they were released around 3 weeks ago.
Click to expand...
Click to collapse
oops....of course. I remember seeing the gold ones for sale but not the Grey
Well I've submitted my return form now and will be waiting to take the hit from Asus. I'm sure it will be an expensive lesson to learn!!
"Kiddies to avoid bricking your brand new Asus Infinity in two seconds - Make sure you read EVERYTHING before doing ANYTHING!"
<walks away with his head down in shame> :crying:
DNO1978 said:
oops....of course. I remember seeing the gold ones for sale but not the Grey
Well I've submitted my return form now and will be waiting to take the hit from Asus. I'm sure it will be an expensive lesson to learn!!
"Kiddies to avoid bricking your brand new Asus Infinity in two seconds - Make sure you read EVERYTHING before doing ANYTHING!"
<walks away with his head down in shame> :crying:
Click to expand...
Click to collapse
Id hate to have to see you do that. Have you tried to flash something from recovery, or reinstall recovery from fastboot (e.g. fastboot flash staging twrp.blob), or reflashing the firmware?
petavium
rightonred said:
Id hate to have to see you do that. Have you tried to flash something from recovery, or reinstall recovery from fastboot (e.g. fastboot flash staging twrp.blob), or reflashing the firmware?
Click to expand...
Click to collapse
Yep, fastboot wont pick the device up attached to the computer. It just hangs at waiting for device. I decided just to send it off as I needed it fixed quick.....pretty sure a solution will turn up the day I get it back
At least it's a chance to test out the customer services in turning it around and how much they charge......
DNO1978 said:
Yep, fastboot wont pick the device up attached to the computer. It just hangs at waiting for device. I decided just to send it off as I needed it fixed quick.....pretty sure a solution will turn up the day I get it back
At least it's a chance to test out the customer services in turning it around and how much they charge......
Click to expand...
Click to collapse
Did Asus repair your table? I have to repair mine because the same brick and I would know how much cost :fingers-crossed:
They repaired it and they didn't charge me!
DNO1978 said:
They repaired it and they didn't charge me!
Click to expand...
Click to collapse
They reflashed your bootloader?
I hope to have your luck
Congrats! :good:
So I pretty much bricked my tablet and can't get into the recovery or fastboot menus and now I'm stuck at the Asus logo screen.
I've searched high and low for a way to un-brick my tablet and get it back in working order but no dice...
My question is.... Do you think/know if there will be a way to un-brick these tablets (without NVflash) in the future? I would send it in to ASUS but I literally just received it back from them due to a screen manufacturing defect.
I just wonder if someone out there has managed to do it and hasn't shared their knowledge or if someone is working on something right now.
Hopeful as ever,
Kordman916
What did you do that you bricked your tablet?
I unlocked the tablet and tried installing Twrp recovery on it. It froze every time I tried booting into recovery so I opened the fastboot menu and hit "Wipe Data" now it just sits at the boot screen with "The device is unlocked" in the corner
Kordman916 said:
I unlocked the tablet and tried installing Twrp recovery on it. It froze every time I tried booting into recovery so I opened the fastboot menu and hit "Wipe Data" now it just sits at the boot screen with "The device is unlocked" in the corner
Click to expand...
Click to collapse
i guess you wiped entire your tablet so there is no system to boot.
You are unrecoverable bricked! I'm sorry.
Sent from my ASUS Transformer Pad TF300T using XDA Premium HD app
Hazard17 said:
You are unrecoverable bricked! I'm sorry.
Sent from my ASUS Transformer Pad TF300T using XDA Premium HD app
Click to expand...
Click to collapse
Are you serious??? I feel like someone would've come up with a solution by now...
Kordman916 said:
Are you serious??? I feel like someone would've come up with a solution by now...
Click to expand...
Click to collapse
Yeah, I think we are screwed. I have fastboot and recovery, but my recovery is the TWRP that doesn't support 4.2.1. Fastboot says is flashes, but it doesn't. It just hangs.
Without the ability to flash a working recovery, I'm afraid we can't fix it. It sucks, I bought my tablet 11 months ago. Waiting for the warranty to be almost over before i flash it. If I would have waited 2 days, I would be fine.
From what I read, Asus wants between $80 and $200.
i thought this was well know by now but by using that wipe data button you brick, completely. you cannot recover. DO NOT EVER USE "WIPE DATA" in bootloader menu. there needs to be a massive banner or something that says this when you enter the tf300 forums IMO.
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
Possible Fix?
sevenalive said:
Yeah, I think we are screwed. I have fastboot and recovery, but my recovery is the TWRP that doesn't support 4.2.1. Fastboot says is flashes, but it doesn't. It just hangs.
Without the ability to flash a working recovery, I'm afraid we can't fix it. It sucks, I bought my tablet 11 months ago. Waiting for the warranty to be almost over before i flash it. If I would have waited 2 days, I would be fine.
From what I read, Asus wants between $80 and $200.
Click to expand...
Click to collapse
Have you tried fastboot flashing the latest version of TWRP?
If you haven't tried it yet, I would recommend you follow the instruction in this thread:
http://forum.xda-developers.com/showthread.php?t=2187982
to install a patched TWRP recovery image (2.4.4.0). This should then let you reinstall a copy of the downloadable ROM from the Aus website.
Once you have installed the update you must re-install the same TWRP 2.4.4.0 again because the Asus ROM update over writes the TWRP recovery files.
Good luck!
:good:
Good luck.
markymark567 said:
i thought this was well know by now but by using that wipe data button you brick, completely. You cannot recover. Do not ever use "wipe data" in bootloader menu. There needs to be a massive banner or something that says this when you enter the tf300 forums imo.
Sent from my asus transformer pad tf300t using xda app-developers app
Click to expand...
Click to collapse
why the f*** did asus put that option there if that's all it does??? It should say "click here if you wanna brick your tablet"
Kordman916 said:
why the f*** did asus put that option there if that's all it does??? It should say "click here if you wanna brick your tablet"
Click to expand...
Click to collapse
lol - but who would hit something without knowing what will happen? I wouldn't dare choose this "wipe data" without knowing, what it means
You can enter wipe data from bootloader menu, when your twrp is working. When your TWRP doesn't exist, wipe data will brick your tablet. So maybe in the future we will be able to install mod which will change icon from Wipe Data to picture with Brick
Kordman916 said:
why the f*** did asus put that option there if that's all it does??? It should say "click here if you wanna brick your tablet"
Click to expand...
Click to collapse
Because it works if your on all stock. and apparently it can work if your twrp is working right, although i say dont even risk it. But im sure it was not known by asus when they put it in there. These tabs are just finiky like that... especially when it comes to recovery
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
Because it's fine with their stock firmware. They don't want you to root it and change it, because they didn't take the proper precautions to prevent bricks. I'm sure they also don't mind the free $$$ for fixing bad flashes. There is a reason why unlocking voids their warranty. They want to charge you to fix it.
I honestly can't imagine ASUS replacing the motherboard of the tablet just to fix it they must be doing something software wise.... I just wonder what it is to fix my damn tablet
Kordman916 said:
I honestly can't imagine ASUS replacing the motherboard of the tablet just to fix it they must be doing something software wise.... I just wonder what it is to fix my damn tablet
Click to expand...
Click to collapse
im sure they have the files and knowledge to restore the tablet through apx mode. they probably use something like nvflash actually..
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
I think that they shouldn't replace motherboard, they only need replace nand memory. They do this for money!
I imagine it must be easier to train employees how to change the motherboard then to flash. Then just have 1 or 2 guys flash motherboards and sort them.
Or they could just be lying and just hook it up to a computer that sends the special stuff needed to flash unrestricted. Then charge you an insane amount for at most 20-30 minutes.
I'm mailing mine off today, won't get to TX until Tuesday since the weekend is here. But I think I'll get mine back before March is out. I'm not happy about the money. I waited for my warranty to be over before I decided to unlock. I killed it by being stupid. i just hope it's not more then the $87 quoted.
This tablet felt slow, never fast. App switching and soft keyboard lag was a big one. I attributed that to the crap flash memory they put in. IO is just as important as CPU/RAM. I think all owners will agree with that. I believed those that they custom firmware is so much better and the tablet speed is improved. I still do. Just sucks I have to pay quite a bit of money to get it fixed and not having a tablet for a few weeks.
Hey guys. Semi newb here. I unlocked my TF300t a while back on the first offical JB update from ASUS. I then followed all the steps to unlock it and use fastboot to install TWRP. This was months back. I have been steadily updating CleanROM Inheritance as the revisions are released.
This latest revision to 3.4.4 flash was easy....as always. I wiped all and installed. When the system came back up I noticed my wifi was broken. I couldnt get it to initialize. So I booted to recovey so I could wipe all and reflash again just in case. Well, TWRP asked me for a password. Ive never encrypted my tablet nor have I used passwrods in the past as I know they can cause issues with access or permissions. I can hit cancel and use twrp but it wont mount anything or allow me to do anything until I 'decrypt' it. Not sure where to go from here. I guess Id like to flash the new official 4.2 from asus but I need advice on how to do this using fastboot.
Any help or pointers are welcomed. I only used the fastboot once to install twrp so I dont completely remember how to use it or if I can use it to flash a full ROM to hopefully reset the tablet. Thanks for any help! Cause I am stumped...
EDIT:
So I tried to turn off the tablet and pressed VOL DN + PWR to get to recovery options and choose fastboot, it just boot loops back to the asus logo twice then goes back in to TWRP. I cant even get into the OS now like I could. I need to unlock TWRP. PLEASE HELP!
EDIT 2:
I just wanted to add that by no means am I putting any blame on the ROM. Its a badass ROM that I love. The issue I am having is most definitely due to the bootloader and TWRP I suspect. I just dont know what I can do in TWRP locked down the way it is to regain some control...or at least fastboot.
cubaniche1 said:
Hey guys. Semi newb here. I unlocked my TF300t a while back on the first offical JB update from ASUS. I then followed all the steps to unlock it and use fastboot to install TWRP. This was months back. I have been steadily updating CleanROM Inheritance as the revisions are released.
This latest revision to 3.4.4 flash was easy....as always. I wiped all and installed. When the system came back up I noticed my wifi was broken. I couldnt get it to initialize. So I booted to recovey so I could wipe all and reflash again just in case. Well, TWRP asked me for a password. Ive never encrypted my tablet nor have I used passwrods in the past as I know they can cause issues with access or permissions. I can hit cancel and use twrp but it wont mount anything or allow me to do anything until I 'decrypt' it. Not sure where to go from here. I guess Id like to flash the new official 4.2 from asus but I need advice on how to do this using fastboot.
Any help or pointers are welcomed. I only used the fastboot once to install twrp so I dont completely remember how to use it or if I can use it to flash a full ROM to hopefully reset the tablet. Thanks for any help! Cause I am stumped...
EDIT:
So I tried to turn off the tablet and pressed VOL DN + PWR to get to recovery options and choose fastboot, it just boot loops back to the asus logo twice then goes back in to TWRP. I cant even get into the OS now like I could. I need to unlock TWRP. PLEASE HELP!
EDIT 2:
I just wanted to add that by no means am I putting any blame on the ROM. Its a badass ROM that I love. The issue I am having is most definitely due to the bootloader and TWRP I suspect. I just dont know what I can do in TWRP locked down the way it is to regain some control...or at least fastboot.
Click to expand...
Click to collapse
It sounds like you flashed the 4.2 update, as that has a new bootloader which causes the behavior you describe. Did you update it to 4.2 before flashing? If so, then check the threads associated with rooting/recovery with 4.2. Basically, you need to install a patched TWRP 2.4.4.0.
jimpmc said:
It sounds like you flashed the 4.2 update, as that has a new bootloader which causes the behavior you describe. Did you update it to 4.2 before flashing? If so, then check the threads associated with rooting/recovery with 4.2. Basically, you need to install a patched TWRP 2.4.4.0.
Click to expand...
Click to collapse
Hey thanks for the reply! Actually, no I was not installing 4.2. I would like to install a newer version of twrp but I cant do anything in twrp because it says its encrypted. I did read that other thread but all the options given are not available to me. I cant get to fastboot.
BUT heres an update:
I got the PC to recognize my device as a Transformer. But I couldn't get the naked drivers nor the newer Asus drivers to work. So I modified the .ini file for both the MTP install and USB driver install to include the Hardware ID shown in windows under device manager properties for the device. Basically I modded the .ini so that it also looks for the device ID, then saved and had windows look at the folder I gain to install the driver and this time is installed. So now I am going to try to use a fastboot command....Ill update if this works. Otherwise I may need to try adb and Im a total newb at adb...
UPDATE:
Got the driver installed but 2 issues:
1: Device manager says Device Cannot Start
2: I cant get recovery menu to show. Tablet goes right into TWRP recovery after looping through the ASUS boot screen twice.
I am stumped. I don't want to give up but I think I may have to
UPDATE
Just an update for those who were following:
I can boot into APX but since I never loaded NVFLASH I was screwed. Nothing I did to try to force it into download mode worked. Bootloader must be screwed. In any case, I went on ebay and bought a TF300T mainboard that was pulled from a damaged screen unit. It was 80 bukcs and should be here soon. I figure 80 bucks is better that 180 from ASUS or drop another 300-400 on a new tablet. I wish there was a JIG for the tablet. I used it on a SG SII once.
cubaniche1 said:
Just an update for those who were following:
I can boot into APX but since I never loaded NVFLASH I was screwed. Nothing I did to try to force it into download mode worked. Bootloader must be screwed. In any case, I went on ebay and bought a TF300T mainboard that was pulled from a damaged screen unit. It was 80 bukcs and should be here soon. I figure 80 bucks is better that 180 from ASUS or drop another 300-400 on a new tablet. I wish there was a JIG for the tablet. I used it on a SG SII once.
Click to expand...
Click to collapse
300-400? buy nexus10 for strong cpu and gpu. and retina display. asus build quality very bad. And support only need money.
chanhny said:
300-400? buy nexus10 for strong cpu and gpu. and retina display. asus build quality very bad. And support only need money.
Click to expand...
Click to collapse
Nexus 10 has it's drawbacks too, I love my TF300T.
UPDATE:
Installed new mainboard and got her back up and running quickly. Already updated to 4.2.1. I like it. Well done ASUS!
chanhny said:
300-400? buy nexus10 for strong cpu and gpu. and retina display. asus build quality very bad. And support only need money.
Click to expand...
Click to collapse
Lol. I love my TF300T. Sure, i can buy a better tablet but I would also have to spend a lot more money. I've only got $299 invested in my 32gb tablet plus $49 in my dock. I'm a happy camper. My tablet , when connected to the dock, will last almost twice as long as the Nexus on one charge. I can also keep using the tablet while the dock is charging. I really never even need to put the tablet itself into the charger. You can't do that with the more expensive Nexus 10.
Sent from my ASUS Transformer Pad TF300T using Tapatalk HD
This feature is one of the reasons I love this tab. I'm having the same problem as op. I can still get into my 4.2 is though but cannot get recovery to read anything. Maybe ill have to wait for a twrp update.
For now as long as the tab works I can deal with it. I would like to get it working the right way again though.
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
klownin5643 said:
This feature is one of the reasons I love this tab. I'm having the same problem as op. I can still get into my 4.2 is though but cannot get recovery to read anything. Maybe ill have to wait for a twrp update.
For now as long as the tab works I can deal with it. I would like to get it working the right way again though.
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
Click to expand...
Click to collapse
Have you added the patch yet? This will allow TWRP to pick up your sd card.
I tried flashing the patched one via fastboot but it did not seem to take. Its still encrypted. I'm thinking its not flashing properly. I'm not the only one having this issue. Hopefully I can just wait it out till a fix is found. I'm afriad of screwing it up to where its completely unuseable.
Sent from my ASUS Transformer Pad TF300T using xda app-developers app