Related
Hey All,
I just got my One XL and I was so excited by the root on 2.20 that I decided to try and flash the custom rom of AOKP on onto it.
After rooting the phone, I did the following:
Flashed TWRP 2.3.1.0 - success
Then I went and saw the thread about the AOKP rom and followed instructions. On that thread, it states that you must flash the boot.img before doing this through fastboot if you are coming forom 2.20 firmware, so I did that. Then I saw that it said on the thread "do not complain about bootlooping if you flashed a custom KERNEL or did not manually flash the stock KERNEL via fastboot" As this was the first custom rom I had attemped with this phone I assumed that I had the stock KERNEL already installed, so I did not flash any kind of kernel.
As soon as I flashed the boot.img from AOKP, I saw that there was red writing on the bootloader about this being for development use only and I noticed that the phone would get past the bootloader to a black screen and then would reboot (boot loop).
I thought that the issue here was that I did not flash the kernel so I went and downloaded the rohan.kernel and flashed that. HOWEVER, I did not realize that I was meant to use recovery to do that and I pushed the boot.img from within the kernel via fastboot instead of using recovery to flash the new kernel (not sure if that matters all that much, but I think that from now on all rom work will be done in the day time after sleeping a little more).
After doing that I see no change in the performance of the phone (it is still boot looping). I am unsure of what to do now. I managed to push the KERNEL zip file and the ROM zip file to the phone via adb but when I try and install them via TWRP I am getting an error because the phone reports that it is unable to mount /sdcard/.
Can one of the far more knowlegable gurus here point me in the right direction? I have wiped the cache and davlik cache numerous times but that has not helped. Should I use TWRP to wipe the system? How can I get the phone back to a place where I can install the new rom?
Thanks!!
ackerchez said:
Hey All,
I just got my One XL and I was so excited by the root on 2.20 that I decided to try and flash the custom rom of AOKP on onto it.
After rooting the phone, I did the following:
Flashed TWRP 2.3.1.0 - success
Then I went and saw the thread about the AOKP rom and followed instructions. On that thread, it states that you must flash the boot.img before doing this through fastboot if you are coming forom 2.20 firmware, so I did that. Then I saw that it said on the thread "do not complain about bootlooping if you flashed a custom KERNEL or did not manually flash the stock KERNEL via fastboot" As this was the first custom rom I had attemped with this phone I assumed that I had the stock KERNEL already installed, so I did not flash any kind of kernel.
As soon as I flashed the boot.img from AOKP, I saw that there was red writing on the bootloader about this being for development use only and I noticed that the phone would get past the bootloader to a black screen and then would reboot (boot loop).
I thought that the issue here was that I did not flash the kernel so I went and downloaded the rohan.kernel and flashed that. HOWEVER, I did not realize that I was meant to use recovery to do that and I pushed the boot.img from within the kernel via fastboot instead of using recovery to flash the new kernel (not sure if that matters all that much, but I think that from now on all rom work will be done in the day time after sleeping a little more).
After doing that I see no change in the performance of the phone (it is still boot looping). I am unsure of what to do now. I managed to push the KERNEL zip file and the ROM zip file to the phone via adb but when I try and install them via TWRP I am getting an error because the phone reports that it is unable to mount /sdcard/.
Can one of the far more knowlegable gurus here point me in the right direction? I have wiped the cache and davlik cache numerous times but that has not helped. Should I use TWRP to wipe the system? How can I get the phone back to a place where I can install the new rom?
Thanks!!
Click to expand...
Click to collapse
First of all I think if you're on 2.2 fw I don't think you can flash kernels through TWRP - I think it has to be through fastboot, I don't know first hand as I'm still on an earlier fw version.
Secondly if you can get into recovery you can flash another rom.
Go to Mount > Mount USB Storage with your phone connected via USB, it should mount as a drive otherwise windows asks you to format format the drive if this happens chances are may have wiped it in bootloader with factory reset or clear storage in either case just format the drive.
You can then drag and drop another rom onto the phone and flash that - remember to extract the boot.img from the rom and flash via fastboot so it will boot.
Goodluck
thejosh86 said:
First of all I think if you're on 2.2 fw I don't think you can flash kernels through TWRP - I think it has to be through fastboot, I don't know first hand as I'm still on an earlier fw version.
Secondly if you can get into recovery you can flash another rom.
Go to Mount > Mount USB Storage with your phone connected via USB, it should mount as a drive otherwise windows asks you to format format the drive if this happens chances are may have wiped it in bootloader with factory reset or clear storage in either case just format the drive.
You can then drag and drop another rom onto the phone and flash that - remember to extract the boot.img from the rom and flash via fastboot so it will boot.
Goodluck
Click to expand...
Click to collapse
Hey!
Thanks a ton for your reply! I managed to get the phone to install a new ROM (AOKP V5) and it seems to boot up. Now when I get into that rom, I see all kinds of things crashing on me. The "Settings" app crashes, the keyboard crashes..any idea?
Did you wipe system, factory reset, davlik and cache from within TWRP before flashing?
Try that otherwise if you're still running into issues post in the thread.
You flashed the 11/10 JB gapps?
Sent from my Nexus 7 using xda premium
ok, i got the phone back up now and have been able to flash stuff properly.
I am working on an issue where after flashing a new rom (AOKP v4) and then a new kernel right after (rohan.kernel V2) the rom seems to hang on the loading splash screen. Has anyone else had this happen? Know how to solve it?
ackerchez said:
ok, i got the phone back up now and have been able to flash stuff properly.
I am working on an issue where after flashing a new rom (AOKP v4) and then a new kernel right after (rohan.kernel V2) the rom seems to hang on the loading splash screen. Has anyone else had this happen? Know how to solve it?
Click to expand...
Click to collapse
Did u wipe everything? (davlik, cache)
Sent from my HTC One XL using xda premium
I been lurking on XDA for a long time just have made any posts, lots of great info has been found here and I usually find my answers without having to ask, that is till now. This might be a long post but I want to give the best information possible to get the best help. I recently updated my tf300t to jb4.2 and that's when the bottom fell out. First I thought I was bricked, flashed the update and it booted fine, flashed twrp and it booted fine, tried flashing Energy rom and that's when it started. Twrp would not mount cache, sd, nothing. Then after rebooting it would give the Asus screen with unlocked bootloader in the top then go straight to twrp, where I could not flash anything. I finally got it to reboot to fastboot where I can reboot to jb but if turned off it will still load straight to twrp and I have to adb fastboot reboot to the RCK android wipe screen and load jb from there using the android. I have tried wiping from that screen, wiping from twrp and even adb push the rom again to wipe with no success. When adb pushing any recovery or rom/software it seems to take but have to manually reboot with power button after to get it to reboot. I tried adb pushing different recoveries with no success along with Energy rom, no success. To me its like I have a dual partition on the storage. Is there any way to wipe everything completely clean and start fresh? Without using recovery since it is not working.
Sounds like you have bricked like a lot of other people. There is a guide in General. Which version of TWRP did you use on the latest bootloader. If it was not TEWRP 2.4.40 or the patched version then you have bricked unfortuntely.....
sbdags said:
Sounds like you have bricked like a lot of other people. There is a guide in General. Which version of TWRP did you use on the latest bootloader. If it was not TEWRP 2.4.40 or the patched version then you have bricked unfortuntely.....
Click to expand...
Click to collapse
I haven't bricked yet, it still works. I just have to adb reboot to bootloader if I power it down and restart it. I just cant wipe it and reinstall anything. I dont remember right off which version of TWRP I did use, but it wont mount anything to allow me to wipe or install from it though.
Hello Forum! I've come here for a little help! Here's My Story.
After running Cyanogen 10.1 Nightlies on 4.2.2 for quite some time, I decided to do a factory reset because my TF300T seemed to be running a little slugish. I DID NOT back it up (mistake #1), DID NOT have USB Debugging on (mistake #2), and, while CWM was wiping /data, I shut off the tablet (STRIKE THREE). Prior to my bonehead move, I had everything else squared away. The unit was fully functional. Now, I'm stuck in this infernal boot loop on the ASUS screen.
I can reboot into recovery, so CWM is not compromised. I have tried to push a new ZIP of the ROM via ADB (unsuccessful, thinking the drivers are nerfed) and through CWM (also unsuccessful).
If anyone has any ideas, please feel free to comment.
P.S. Please don't kill me Mods, I'll be good after this
Update:
After looking through the forums more I tried all of these:
Installed the Universal Naked Driver (Sorta Worked)
Reflashed the system blob from the most recent CyanogenMod Nightly (Says it wrote, I doubt it did)
Went into CWM, tried to Sideload the CM zip (Didn't work)
Then, I took my external SD, placed the CM zip onto it, rebooted the tablet w/ the SD in it, booted into CWM, TRIED a full system wipe (couldn't mount /data), and reflashed the ROM. That worked! ... sorta. Upon "successful install", I had CWM reboot the TF300T. It came to the ASUS Screen w/ a progress bar (went from 1% to 100% within a second). However, after that, it went back to the bootloop ASUS screen
I feel like I'm close on this one, any tips?
Kazman101 said:
Update:
After looking through the forums more I tried all of these:
Installed the Universal Naked Driver (Sorta Worked)
Reflashed the system blob from the most recent CyanogenMod Nightly (Says it wrote, I doubt it did)
Went into CWM, tried to Sideload the CM zip (Didn't work)
Then, I took my external SD, placed the CM zip onto it, rebooted the tablet w/ the SD in it, booted into CWM, TRIED a full system wipe (couldn't mount /data), and reflashed the ROM. That worked! ... sorta. Upon "successful install", I had CWM reboot the TF300T. It came to the ASUS Screen w/ a progress bar (went from 1% to 100% within a second). However, after that, it went back to the bootloop ASUS screen
I feel like I'm close on this one, any tips?
Click to expand...
Click to collapse
I would try to install TWRP recovery since CWM is sometimes a bit flaky, I would use TWRP 2.3.3.0 since I believe is the most stable but you can install the latest one 2.4.4.0, then flash the blob file via fastboot (instructions are at the twrp site) and repeat the same process as you did with CWM, wipe everything and then flash CM.zip from external SD and see if it works that way. If that does not work, try reflashing the stock system blob from Asus this time using fastboot and that will put you completely stock and then you can start over.
hope it helps.
Erik
ricco333 said:
I would try to install TWRP recovery since CWM is sometimes a bit flaky, I would use TWRP 2.3.3.0 since I believe is the most stable but you can install the latest one 2.4.4.0, then flash the blob file via fastboot (instructions are at the twrp site) and repeat the same process as you did with CWM, wipe everything and then flash CM.zip from external SD and see if it works that way. If that does not work, try reflashing the stock system blob from Asus this time using fastboot and that will put you completely stock and then you can start over.
hope it helps.
Erik
Click to expand...
Click to collapse
It Unbricked!
Step 1: Flashed TWRP 2.4.4.0 blob file to overwrite CWM (Check)
Step 2: Factory Reset and Wipe Entire Device (CHECK!?!?!)
Step 3: Flash CM.zip!?!?! (Not So Check ... PLAN B!)
Downloaded Chinese Stock system blob (don't ask, I know it was stupid, but go with me here)
Flashed the system blob (after 3 minutes ... SUCCESS!)
No more boot loop and back to stock ... now to root it again to get my sweet CyanogenMod back ...
Thank you Erik, your help was much appreciated!
My buddy is having a hard time flashing a new ROM on his tablet. Currently he's running Cyanogen with TWRP.
Apparently TWRP formatted his tablet randomly and he hasn't been able to install a new ROM because his tablet won't mount the system or cache. It keeps failing. Neither system or cache are selectable to mount and it says "E: unable to mount '/system' "
And ADB isn't pushing anything.
Any thoughts why?
Sunset Rider said:
My buddy is having a hard time flashing a new ROM on his tablet. Currently he's running Cyanogen with TWRP.
Apparently TWRP formatted his tablet randomly and he hasn't been able to install a new ROM because his tablet won't mount the system or cache. It keeps failing. Neither system or cache are selectable to mount and it says "E: unable to mount '/system' "
And ADB isn't pushing anything.
Any thoughts why?
Click to expand...
Click to collapse
TWRP formatted his tablet randomly??? Never heard of such a thing!
And we need more information:
What versions of bootloader, CM, TWRP and you are trying to push what in ADB?
Do you have access to fastboot? What rom are you trying to flash?
What did he do - as best as he can remember?
berndblb said:
TWRP formatted his tablet randomly??? Never heard of such a thing!
And we need more information:
What versions of bootloader, CM, TWRP and you are trying to push what in ADB?
Do you have access to fastboot? What rom are you trying to flash?
What did he do - as best as he can remember?
Click to expand...
Click to collapse
It wiped his data when he went to decrypt data and it asked for a password. He hit cancel and it said system memory 0gb
He has the newest twrp, he was on 10.2 trying to go to 11, and he was trying to push the mounting through adb and was getting errors. Because he is unable to select them In twrp
He has fastboot but it doesn't respond to commands at all.
Thank you for any help
fastboot
Sunset Rider said:
It wiped his data when he went to decrypt data and it asked for a password. He hit cancel and it said system memory 0gb
He has the newest twrp, he was on 10.2 trying to go to 11, and he was trying to push the mounting through adb and was getting errors. Because he is unable to select them In twrp
He has fastboot but it doesn't respond to commands at all.
Thank you for any help
Click to expand...
Click to collapse
Sounds like a soft brick.. Due to a wrong recovery flash or he flashed the newest version of twrp, and did a full data wipe.. It has known issues!!!!!
Becareful from here.. Like berndblb said we need verify we still have fastboot access!!:fingers-crossed:
What is the OS of the PC your using to fastboot from??
Well I tried installing cromi for him and it stalls at 87%
Sunset Rider said:
Well I tried installing cromi for him and it stalls at 87%
Click to expand...
Click to collapse
UPDATE: We restarted the tablet, mid installation because it froze, and it booted up to his old 10.2 just fine. I recommended he do a clean format now but he doesn't want to do anything lol.
So right now I'm just thanking God he didn't brick it hard
Sunset Rider said:
It wiped his data when he went to decrypt data and it asked for a password. He hit cancel and it said system memory 0gb
Click to expand...
Click to collapse
Did he have the tablet encrypted or did the request for a decryption password just show up unexpectedly? If it's the latter - I have read about this a number of times - unfortunately still cannot make rhyme or reason out of it, but I suspect it's a corrupted recovery....
He has the newest twrp, he was on 10.2 trying to go to 11, and he was trying to push the mounting through adb and was getting errors. Because he is unable to select them In twrp
Click to expand...
Click to collapse
The newest meaning 2.6.3.2?
He has fastboot but it doesn't respond to commands at all.
Thank you for any help
Click to expand...
Click to collapse
Which probably means he doesn't have the correct fastboot drivers installed. That would No. 1: Get fastboot working. Download the Google Universal Naked drivers, install them and try
Code:
fastboot devices
If that returns the tablet's serial number, you're in business. You could then flash CWM 6.0.4.6 in fastboot. I would probably wipe data (hope he has everything backed up) and flash the rom.
---------- Post added at 10:18 PM ---------- Previous post was at 10:10 PM ----------
lj50036 said:
Sounds like a soft brick.. Due to a wrong recovery flash or he flashed the newest version of twrp, and did a full data wipe.. It has known issues!!!!!
Becareful from here.. Like berndblb said we need verify we still have fastboot access!!:fingers-crossed:
What is the OS of the PC your using to fastboot from??
Click to expand...
Click to collapse
@lj50036 could you elaborate on the issues of TWRP 2.6.3.2.? sbdags included it it in his bootloader/TWRP flash package for CROMi-X and one guy just softbricked flashing CROMi_X after flashing that package, he seems to have done everything else correctly and I suspect the recovery is buggy???
TWRP
could you elaborate on the issues of TWRP 2.6.3.2.? sbdags included it it in his bootloader/TWRP flash package for CROMi-X and one guy just softbricked flashing CROMi_X after flashing that package, he seems to have done everything else correctly and I suspect the recovery is buggy???
Click to expand...
Click to collapse
My issues are first hand.. It flashes just fine, everything seems to function correctly.. It's only the wiping of data that has a issue.... It just hangs says its doing it thing but nothing ever happens..After a hard reboot TWRP now asking for password will not mount any storage of any kind... The fastest way to a soft brick.... I posted on the TWRP forum, about the issue... Maybe we need a new forum letting people know about the issue, so we dont end up with a riot!!!
lj50036 said:
My issues are first hand.. It flashes just fine, everything seems to function correctly.. It's only the wiping of data that has a issue.... It just hangs says its doing it thing but nothing ever happens..After a hard reboot TWRP now asking for password will not mount any storage of any kind... The fastest way to a soft brick.... I posted on the TWRP forum, about the issue... Maybe we need a new forum letting people know about the issue, so we dont end up with a riot!!!
Click to expand...
Click to collapse
Thanks! Though I would love to see what a riot on XDA looks like LOL
berndblb said:
Did he have the tablet encrypted or did the request for a decryption password just show up unexpectedly? If it's the latter - I have read about this a number of times - unfortunately still cannot make rhyme or reason out of it, but I suspect it's a corrupted recovery....
The newest meaning 2.6.3.2?
Which probably means he doesn't have the correct fastboot drivers installed. That would No. 1: Get fastboot working. Download the Google Universal Naked drivers, install them and try
Code:
fastboot devices
If that returns the tablet's serial number, you're in business. You could then flash CWM 6.0.4.6 in fastboot. I would probably wipe data (hope he has everything backed up) and flash the rom.
---------- Post added at 10:18 PM ---------- Previous post was at 10:10 PM ----------
@lj50036 could you elaborate on the issues of TWRP 2.6.3.2.? sbdags included it it in his bootloader/TWRP flash package for CROMi-X and one guy just softbricked flashing CROMi_X after flashing that package, he seems to have done everything else correctly and I suspect the recovery is buggy???
Click to expand...
Click to collapse
It was version 2.6.3.0.
He had no decrypted files he was just seeing what it did when he hit decrypt data. I asked for a password which he obviously never set and hit cancel. And it said he had nothing in internal storage.
However, after the install froze on an older Cromi version I put on his sd card (from my 700t), we held down the power button and rebooted. It booted up fine to his previous Cyanogen 10.2. WITH all of his internal storage still there, EVEN THOUGH, he did a format from TWRP already.
So it's definitely a problem with TWRP. His tablet is back to the way it was before the fiasco and he is afraid to do anything else.
Sunset Rider said:
It was version 2.6.3.0.
He had no decrypted files he was just seeing what it did when he hit decrypt data. I asked for a password which he obviously never set and hit cancel. And it said he had nothing in internal storage.
However, after the install froze on an older Cromi version I put on his sd card (from my 700t), we held down the power button and rebooted. It booted up fine to his previous Cyanogen 10.2. WITH all of his internal storage still there, EVEN THOUGH, he did a format from TWRP already.
So it's definitely a problem with TWRP. His tablet is back to the way it was before the fiasco and he is afraid to do anything else.
Click to expand...
Click to collapse
Are you sure about this???
Because TWRP 2.6.3.0 was too big for the recovery partition of the TF700 and never properly installed????
For any reliable advice you need to provide the bootloader version (which you still haven't given us) and if you have a working system, you should be able to boot into recovery and give us it's version number.
For installing CM 11 on the TF700 you need to be on the 10.6.1.14.10 bootloader and have the CWM 6.0.4.6 recovery.
TWRP 2.6.3.2 supposedly works with CM 11, but I would not trust it - read about too many problems with it....
And anyway - in terms of performance, neither CM 10.2 or CM 11 beats CROMi-X on this tablet - period.
Here I am
berndblb said:
Are you sure about this???
Because TWRP 2.6.3.0 was too big for the recovery partition of the TF700 and never properly installed????
For any reliable advice you need to provide the bootloader version (which you still haven't given us) and if you have a working system, you should be able to boot into recovery and give us it's version number.
For installing CM 11 on the TF700 you need to be on the 10.6.1.14.10 bootloader and have the CWM 6.0.4.6 recovery.
TWRP 2.6.3.2 supposedly works with CM 11, but I would not trust it - read about too many problems with it....
And anyway - in terms of performance, neither CM 10.2 or CM 11 beats CROMi-X on this tablet - period.
Click to expand...
Click to collapse
Hey guys, this is Wade, the cause of the whole fiasco.
It was the newest TWRP 2.3.6.2, but I imagine it might've been a problem with the bootloader? I had no idea that the bootloader needed updating; I thought that once you could boot what you wanted, that was it, but obviously I'm mistaken. Where do I find the bootloader version? It was the latest posting to the Asus download site, or the V8, 2013 bootloader edition for JB. 4.2
Basically, I had tried several times that day installing CM11 and the gapps with CWM 6.0.3.1 (which ROM manager says is the up to date version? WTF?) to no avail. It kept giving me md5sum errors, and I couldn't find anything to easily fix that. CWM would also not respond to commands from ROM manager other than backups... If i told it to bootload and flash, it would just reboot normally... ADB also would fail, despite saying that i COULD connect to fastboot.
So i read on the actual CM forum that the newest TWRP 2.6.3.2 would do the trick as well, and tried that. But ya, once i booted into twrp, it threw a password query at me. I never set a password, so I pressed cancel, and that's when the partition showed up as blank.
I went to reboot, but it warned that I had no OS installed. That's about when I freaked out. It would see my microSD fine, but wasn't able to talk to /system to actually flash anything, and ADB would just give "error:closed" if I tried any mount commands there.
So ya, I invited my buddy over, and he recommended we try flashing an old CROMI-X, and it WORKED! sort of. It started to flash, even though a previous CM 10.2 and it's gapps (which I was already running and knew worked) wouldn't!
Then it froze installing Youtube, and after ten mins we held down the power.
And it booted back into CM 10.2 like nothing had happened.
Even though TWRP said I had succesfully factory reset AND wiped AND formatted the internal by that point. Lies!
So ya, I imagine it's a combination of pilot error, and TWRP being a little fluky. My question - where did that 87% CROMI-X flash go, and how can I get rid of it? And i reflashed CWM 6.0.3.1, but I'm still wary of going into the bootloader, just in case bastard TWRP is still lurkin
UPDATE
Wadesauce said:
I had no idea that the bootloader needed updating; I thought that once you could boot what you wanted, that was it, but obviously I'm mistaken. Where do I find the bootloader version? It was the latest posting to the Asus download site, or the V8, 2013 bootloader edition for JB. 4.2
Click to expand...
Click to collapse
So it was definitely the old ASUS 4.2 bootloader I was using. I had no idea that dasunsrule32 wanted us to use his April 2013 bootloader for 10.2 as well, the site that told me how to put CM 10.2 on my tab said to use the old ASUS one.
Finally manned up and tried my first soft reboot, and it brought up the ASUS menu with the blue loading bar - it seemed like it wanted to go into bootloader. Then it went blank and the regular ASUS logo showed, and then the CM logo and booted. So i didn't walk away from this unscathed; something low-down got messed with...
Can I update the bootloader to his, despite the problems ive been having? How do I do that?
And why does ROM manager only offer 6.0.3.1??
And since CM11 is based on 4.4, wont it eventually be better than CROMi-X?
Wadesauce said:
So it was definitely the old ASUS 4.2 bootloader I was using. I had no idea that dasunsrule32 wanted us to use his April 2013 bootloader for 10.2 as well, the site that told me how to put CM 10.2 on my tab said to use the old ASUS one.
So can I update the bootloader to his, despite the problems ive been having? How do I do that?
And why does ROM manager only offer 6.0.3.1??
And since CM11 is based on 4.4, wont it eventually be better than CROMi-X?
Click to expand...
Click to collapse
Can you still boot into fastboot mode on your tablet and can your PC see the tablet in fastboot mode?? What is the OS on your PC??
i dunno
lj50036 said:
Can you still boot into fastboot mode on your tablet and can your PC see the tablet in fastboot mode?? What is the OS on your PC??
Click to expand...
Click to collapse
I haven't tried booting into bootloader, or even a full power down/power up yet. This is the device I use for school and right now would be a pretty sh**y time for anything serious to happen to it.
I am mainly afraid that TWRP hasn't left yet, or that I won't be able to access the CWM that ROM manager says I just successfully reflashed.
I don't really want to plug it back into the computer until I know more about what happened to it. Is it likely that the CROMI that we tried flashing or the old TWRP will cause me problems? Remember that CROMI said it was 87% successful (had loaded kernel and system and all that jazz)
And I have 64 bit Win7, it should have appropriate drivers
Feedback
Wadesauce said:
I haven't tried booting into bootloader, or even a full power down/power up yet. This is the device I use for school and right now would be a pretty sh**y time for anything serious to happen to it.
I am mainly afraid that TWRP hasn't left yet, or that I won't be able to access the CWM that ROM manager says I just successfully reflashed.
I don't really want to plug it back into the computer until I know more about what happened to it. Is it likely that the CROMI that we tried flashing or the old TWRP will cause me problems? Remember that CROMI said it was 87% successful (had loaded kernel and system and all that jazz)
And I have 64 bit Win7, it should have appropriate drivers
Click to expand...
Click to collapse
Well you just let me know.. I will be here to help out if you would like it ....As always thx lj
Wadesauce said:
Hey guys, this is Wade, the cause of the whole fiasco.
It was the newest TWRP 2.3.6.2, but I imagine it might've been a problem with the bootloader? I had no idea that the bootloader needed updating; I thought that once you could boot what you wanted, that was it, but obviously I'm mistaken. Where do I find the bootloader version? It was the latest posting to the Asus download site, or the V8, 2013 bootloader edition for JB. 4.2
Basically, I had tried several times that day installing CM11 and the gapps with CWM 6.0.3.1 (which ROM manager says is the up to date version? WTF?) to no avail. It kept giving me md5sum errors, and I couldn't find anything to easily fix that. CWM would also not respond to commands from ROM manager other than backups... If i told it to bootload and flash, it would just reboot normally... ADB also would fail, despite saying that i COULD connect to fastboot.
So i read on the actual CM forum that the newest TWRP 2.6.3.2 would do the trick as well, and tried that. But ya, once i booted into twrp, it threw a password query at me. I never set a password, so I pressed cancel, and that's when the partition showed up as blank.
I went to reboot, but it warned that I had no OS installed. That's about when I freaked out. It would see my microSD fine, but wasn't able to talk to /system to actually flash anything, and ADB would just give "error:closed" if I tried any mount commands there.
So ya, I invited my buddy over, and he recommended we try flashing an old CROMI-X, and it WORKED! sort of. It started to flash, even though a previous CM 10.2 and it's gapps (which I was already running and knew worked) wouldn't!
Then it froze installing Youtube, and after ten mins we held down the power.
And it booted back into CM 10.2 like nothing had happened.
Even though TWRP said I had succesfully factory reset AND wiped AND formatted the internal by that point. Lies!
So ya, I imagine it's a combination of pilot error, and TWRP being a little fluky. My question - where did that 87% CROMI-X flash go, and how can I get rid of it? And i reflashed CWM 6.0.3.1, but I'm still wary of going into the bootloader, just in case bastard TWRP is still lurkin
Click to expand...
Click to collapse
Jeez - where to start?
First of all: Do yourself a favor and ditch ROM Manager. It does not work well with the TF700 and several people have hard bricked using it. You have been very lucky so far!
Second: Do not flash anything until you are 150% sure you know what you are doing, you understand the requirements for your situation and have everything you need at hand.
Do not flash anything EVER if you do not know what bootloader version you have. That's like getting into your car blind folded and trusting that your GPS will drive you safely to your destination.
Every ROM has it's requirements in terms of bootloader version and recovery and they are usually clearly stated in the first couple of paragraphs in the OP of the rom thread. If not: Stay away from that rom unless you know exactly what you are doing!
TWRP 2.6.3.2 has major issues when formatting data from it. Stay away from it for now.
To find out what you can do to get a stable system back, you need to know where you are and what you have.
Boot into the bootloader (and do not use ROM Manager to do it!) and read the tiny script. It'll probably be 10.6.1.14.10 or .8
Post the result.
Boot into the recovery to check what you have installed. Versions matter!
The proper way of installing a custom recovery is in fastboot mode. Which is different from ADB, btw - you've been mixing those up I think.
Google "adb fastboot tutorial" and do some reading. Once you understand, get it set up on your PC, boot the tablet into the bootloader, connect both via original USB cable and test the connection with
Code:
fastboot devices
If it returns the serial number of your tablet, you are in business and we can continue from there.
Happy studying!
Getting there...
berndblb said:
Google "adb fastboot tutorial" and do some reading. Once you understand, get it set up on your PC, boot the tablet into the bootloader, connect both via original USB cable and test the connection with
Code:
fastboot devices
If it returns the serial number of your tablet, you are in business and we can continue from there.
Happy studying!
Click to expand...
Click to collapse
Alright, I have done some reading as far as all of this goes. I understand a lot of it better now.
So I'm positive now that it was because I hadn't updated my bootloader before trying through CWM. And TWRP obviously was no more useful.
I haven't quite checked what the bootloader version is - I think there may be something wrong with it still (given my weird boot-up) and I don't want to go there until I'm totally sure what I'm doing. I'd hate to hit bootloader and then realize something was seriously wrong, and my time was ticking.
However, I have never changed the bootloader since I used ASUS's one from their website originally - since it says v8, I imagine thats the .8 one?
Before I uninstalled ROM manager, I checked what it said my recovery was - and it said I had CWM 6.0.3.1 still, even though the TWRP fiasco has just gone down. I used ROM to reflash the same 6.0.3.1 from the device, and it said it was successful.
So before I begin, could i possibly ask a few questions?
1) Could I have corrupted the bootloader?
2) Can more than one recovery exist? Is it maybe true that CWM 6.0.3.1 would be the one I will boot into if I went into recovery? I REALLY don't want it to be TWRP again as it might not survive the experience (I had put TWRP on via fastboot). Should I just get to bootloader, flash a new recovery right away and go from there?
3) When I go to finally solve it, what are the hypothetical steps I should take? Right now, as far as I can tell, it will be:
a) Make sure all drivers are working, and files (including backup) are on my PC.
b) reboot into bootloader, check version.
c) flash the 10.6.1.14.4 bootloader
d) reboot
e) reboot into bootloader
f) flash CWM. 6.0.4.6
g) reboot
i) reboot into bootloader, into recovery, then flash CM 11 and gapps
j) reboot
Ya? No? Any help would be appreciated
Wadesauce said:
Alright, I have done some reading as far as all of this goes. I understand a lot of it better now.
So I'm positive now that it was because I hadn't updated my bootloader before trying through CWM. And TWRP obviously was no more useful.
I haven't quite checked what the bootloader version is - I think there may be something wrong with it still (given my weird boot-up) and I don't want to go there until I'm totally sure what I'm doing. I'd hate to hit bootloader and then realize something was seriously wrong, and my time was ticking.
However, I have never changed the bootloader since I used ASUS's one from their website originally - since it says v8, I imagine thats the .8 one?
Before I uninstalled ROM manager, I checked what it said my recovery was - and it said I had CWM 6.0.3.1 still, even though the TWRP fiasco has just gone down. I used ROM to reflash the same 6.0.3.1 from the device, and it said it was successful.
So before I begin, could i possibly ask a few questions?
1) Could I have corrupted the bootloader?
2) Can more than one recovery exist? Is it maybe true that CWM 6.0.3.1 would be the one I will boot into if I went into recovery? I REALLY don't want it to be TWRP again as it might not survive the experience (I had put TWRP on via fastboot). Should I just get to bootloader, flash a new recovery right away and go from there?
3) When I go to finally solve it, what are the hypothetical steps I should take? Right now, as far as I can tell, it will be:
a) Make sure all drivers are working, and files (including backup) are on my PC.
b) reboot into bootloader, check version.
c) flash the 10.6.1.14.4 bootloader
d) reboot
e) reboot into bootloader
f) flash CWM. 6.0.4.6
g) reboot
i) reboot into bootloader, into recovery, then flash CM 11 and gapps
j) reboot
Ya? No? Any help would be appreciated
Click to expand...
Click to collapse
1. No, your bootloader is still good because you still can boot into your system. You need your bootloader to initiate your hardware before your OS is booting.. I am very sure that is the case but it would be nice for someone to confirm it...
2. Your recovery partition is too small for two custom recoveries to exist. So it is almost impossible for you to have two recoveries..
Before you want to go further, it is easier to find out your bootloader and recovery versions so you know what is the next step that you need to do. Otherwise, it is just a guess or a shot in the dark... I think that you are fine but you need to wait for some experts to confirm it... Good luck...:fingers-crossed:
Please bear with me
LetMeKnow said:
Before you want to go further, it is easier to find out your bootloader and recovery versions so you know what is the next step that you need to do. Otherwise, it is just a guess or a shot in the dark... I think that you are fine but you need to wait for some experts to confirm it... Good luck...:fingers-crossed:
Click to expand...
Click to collapse
Sorry hahah, I know I must seem really frustrating...
I have held off for 2 reasons:
1. The first time I did a soft reboot after my fiasco, upon boot it went through the first series of steps trying to load into the bootloader, but then booted fine. Another time a few days after, it rebooted while i was using it, and just went blank after the asus logo. Holding the power down caused it to boot fine. Still, neither of those had ever happened before, and I am pretty sure that some point along the line of bootloader-->OS something is broken. Hopefully on the OS side.
2. I am not going to attempt to boot into recovery until I know that it isn't the same TWRP 2.6.3.2 that got me into this whole fiasco. I know it sounds like a catch 22, not wanting to reboot into recovery to check what it is, but I have NO IDEA how to get out of this TWRP as it stands. I had to flash a CROMI (which failed at 87%) and hard reboot. Not willing to go out on a limb and assume that hard-reboot will work during any step of that process.
So, why do I have to check it? Can't I boot into bootloader, flash a new bootloader, flash a new recovery, and then reboot normally? Assuming I'll be able to establish fastboot (drivers still work, so fingers crossed on that one).
Hello,
My TF700 was on a CleanRom (2.3 i think), for a while, i decided to update.
- I installed the latest CWM (via fastboot) and flashed a Cyanogen 10.2 "stable", but my tablet freezed very quickly after successful boot, i tried some reboots and get same problem.
- I tried to install a stock ODEX root ROM, the tablet freezed at asus logo
- I flashed TWRP instead of CWM, it doesn't helped
- I tried wipe data and cache with TWRP, then my data was not accessible anymore and TWRP was unable to re-create it
- I searched on forums and found on this one that flash a boot.blob file can solve the problem
- It doesn't and now CWM and TWRP refuse to work ....
So i post here before getting my tablet completely brick.
At this point, i get access to fastboot / abd, CWM load but don't work (reboot when trying to do something), TWRP don't load.
Any suggestion to get back to a Stock ODEX rooted rom ?
Excuse my english ...
Asphodele said:
Hello,
My TF700 was on a CleanRom (2.3 i think), for a while, i decided to update.
- I installed the latest CWM (via fastboot) and flashed a Cyanogen 10.2 "stable", but my tablet freezed very quickly after successful boot, i tried some reboots and get same problem.
- I tried to install a stock ODEX root ROM, the tablet freezed at asus logo
- I flashed TWRP instead of CWM, it doesn't helped
- I tried wipe data and cache with TWRP, then my data was not accessible anymore and TWRP was unable to re-create it
- I searched on forums and found on this one that flash a boot.blob file can solve the problem
- It doesn't and now CWM and TWRP refuse to work ....
So i post here before getting my tablet completely brick.
At this point, i get access to fastboot / abd, CWM load but don't work (reboot when trying to do something), TWRP don't load.
Any suggestion to get back to a Stock ODEX rooted rom ?
Excuse my english ...
Click to expand...
Click to collapse
Hey Your in the right place
Shoot me an email, we can review your issues and if we find a solution we can post back here to help
XDA users with there issues....
My email is everywhere talke a look around
Thx Josh
Asphodele said:
Hello,
My TF700 was on a CleanRom (2.3 i think), for a while, i decided to update.
- I installed the latest CWM (via fastboot) and flashed a Cyanogen 10.2 "stable", but my tablet freezed very quickly after successful boot, i tried some reboots and get same problem.
- I tried to install a stock ODEX root ROM, the tablet freezed at asus logo
- I flashed TWRP instead of CWM, it doesn't helped
- I tried wipe data and cache with TWRP, then my data was not accessible anymore and TWRP was unable to re-create it
- I searched on forums and found on this one that flash a boot.blob file can solve the problem
- It doesn't and now CWM and TWRP refuse to work ....
So i post here before getting my tablet completely brick.
At this point, i get access to fastboot / abd, CWM load but don't work (reboot when trying to do something), TWRP don't load.
Any suggestion to get back to a Stock ODEX rooted rom ?
Excuse my english ...
Click to expand...
Click to collapse
Sounds like you are on an old bootloader. Flash the stock rom from asus by unzipping the zip you download from their website and placing in the root folder of your micro sd and then go into rck from the bootloader menu (power + volume down whilst booting)
Or you could just flash it from recovery....
lj50036 helped me to flash a new bootloader, recovery, rom and nvflash to make it unbrickable
Not just helped he spent many times to explain me how it works and what he did.
He is very nice and this was a pleasure to talk with him, i'm happy that there's still person like that on this planet
see you !
Asphodele said:
lj50036 helped me to flash a new bootloader, recovery, rom and nvflash to make it unbrickable
Not just helped he spent many times to explain me how it works and what he did.
He is very nice and this was a pleasure to talk with him, i'm happy that there's still person like that on this planet
see you !
Click to expand...
Click to collapse
I buy a tf700 with cm 11 a few days ago i am really interessted on how this steps works. I really want to make it unbrickeable, But i dont really understand how it works. I can not enter in fastboot. at least i got cwm interface when rebooting with adb into recovery.
Can u explain how you did it?
It invovles flashing a modified bootloader and the flatline recovery and then using Wheelie to generate your nvflash blobs.
Step-by-step instructions (which you need to follow to the letter) are here:
https://www.androidroot.mobi/pages/guides/tegra3-guide-nvflash-jellybean/
Stuck in boot loop, fastboot and recovery accessible
Hello,
I'm having a similar issue and I need help! Initially my tablet was rooted with Cromi-X 5.4. Then I decided to try Crombi-KK.
Here is what happened:
- Updated TWRP recovery
- Did a full wipe as recommended
- Flashing got stuck at the Crombi-KK loading sign
- Tried to reflash but TWRP wasn't detecting data partition anymore
- Instead installed the other recommended recovery CWMR.
- Flashed Crombi-KK, it worked. Played around with it for a few days, it was wonderful, fast and responsive.
- Battery died out and when I turned it back on I got a UIDs system inconsistent error.
- I found online many recommendations to reflash so I tried to do that
- Since then I'm stuck in a boot loop. I see the initial "bios" Asus logo then it restarts over and over.
- I am able to access bootloader and recovery
I've tried reflashing the asus stock blob. I've tried wiping the data through CWMR but it starts working and then it restarts. I don't know what to do anymore, so if anyone can help me, I would really appreciate it!
Thanks
Which recovery and bootloader version do you have now?
A (for KK) outdated bootloader seems the most likely culprit.
You can try save the recovery log when you flash or grab a logcat of the bootloop, but probably it'll only tell you that the recovery cannot mount /data.
Determine that you are on the correct bootloader, if not update it. If you're lucky the tablet will start right up. If it doesn't, formatting /data is the only way I know to get it back. Not just wiping - formatting it. You will loose everything on internal SD, so I hope you have a nandroid you can restore from later.
If you use TWRP 2.7+ be aware that formatting can take more than an hour. Let it finish!
For good measure, download CROMBi-KK again, check the md5 and then flash that file.
I'm on 10.6.1.14.10 bootloader which I think is the latest one
I have 6.0.4.7 CWMR
I'm trying to format data completely but when i do it in CWMR it starts and then the tablet reboots on it's own after a couple of minutes.
How can I retrieve the logs, I never had to do it before.
Thanks for your help
Mhh, getting a little more complicated.
Your BL is ok...
What do you see in CWM when you go into Mounts and Storage? What is mounted?
The recovery logs are under Advanced > show logs.
I'm at work now but from what I remember the only thing mounted was the cache. I'll double check tonight. Do you think there's any hope or I have a brand new paper weight?
yasyas said:
I'm at work now but from what I remember the only thing mounted was the cache. I'll double check tonight. Do you think there's any hope or I have a brand new paper weight?
Click to expand...
Click to collapse
Can you fastboot flash twrp?
It's much much better than CWM, has its own terminal and will be easier to offer the correct format command.
sbdags said:
Can you fastboot flash twrp?
It's much much better than CWM, has its own terminal and will be easier to offer the correct format command.
Click to expand...
Click to collapse
So I flashed TWRP and when I go in mount/storage everything is selected except for system. Should I do a format data from the wipe menu before flashing crombi-kk again?
yasyas said:
So I flashed TWRP and when I go in mount/storage everything is selected except for system. Should I do a format data from the wipe menu before flashing crombi-kk again?
Click to expand...
Click to collapse
To be in the safe side, yes, that is what I would do. TWTRP 2.7.+ takes a long time to format and it may seem the process got stuck. Give it at least 90 minutes to finish.
Then reflash CROMBi
I'm back up and running !!!
This time installing TWRP, everything was mounted (maybe my previous flash before CWMR wasn't good), did a format data, waited until it was done, flashed latest Crombi-KK and going through setup now. Hopefully won't have the same UID issue on next shutdown. I didn't enable fsync or journaling so hopefully it won't happen again.
Thanks both of you for your help!
Good deal! Happy for you!
Rooting google pixel zl