Related
Working on porting ICS to the Lanyu 910 / X10 Airpad MID-910. I think the kernel sources used for the Pascal2 could possibly work with the 910 after some config changes.
Basically with the 910 we have no stock kernel source available for reference, no stock configuration, no detailed hardware inside the device.. We know it uses the rk2918 rockchip and I know it uses the SWL-2480 / Marvel 8686, simply from observing the identifying markings on the chip. Other than that, all we know is that it uses a 2.6.32 kernel with android 2.3, has an unknown 7" capacitive touch screen, unknown camera, etc. In order for ICS to work with the 910 we'll have to use a 3.0.8+ kernel or backport all of the required components from 3.x to our working 2.6.32 sources -however we don't have the patched sources for the stock firmware, so we are better off to just use 3.0.8 kernel that the source is available for on many rk2918 devices - of course we'd have to make configuration changes to our specific hardware, and possibly patch the sources with modified/new source code for our specific hardware (if we can obtain it).
Pascal 2 has a realtek based wireless chipset.. 910 uses the SWL-2940 / Marvel 8686, the module for this is also included in the kernel sources. The 910 has an unknown touchscreen, so the kernel for the pascal2 may or may not work with the touch screen settings. It is quiet difficult to work on the kernel without in depth knowledge of all the hardware. The 910 has Lanyu printed on the motherboard, and I'm not successful in finding any detailed hardware information for the board on the 910.
Also I am concerned with the memory mappings since the 910 only has 512mb ram and the pascal2 has 1GB+
Really wish these Chinese tablet manufacturers would follow the rules of GPL and release their source code, it would help A LOT with getting ICS to work with the 910.
As far as the rockchip and the ICS rom that vurrut has put together, I am almost 100% sure that the system.img that he used will work with the 910 as long as I get a working 3.0.8 kernel for ICS reconfigured/recompiled and implement some changes in the boot.img for the init services relating to hardware.
If anyone has the X10 airpad (rk2918 based) or the Lanyu 910 and has some important information regarding the internal hardware, please contact me with details, as I can probably get a working kernel for our device in a matter of hours.
Needed:
Gsensor/Accelerometer MFG/Model
Input Keys Controller - MFG/Model
Battery Sensor Chip - MFG/Model
TouchScreen/Display - MFG/Model
Other mainboard chipsets - MFG/Model (excluding RK2918 Rockchip SoC)
It would be of much help if there was someone here knows the MFG/Model of any of the above hardware, and it would also be a great help if anyone knows what linux kernel drivers are used for any of the components inside the 910.
When I was working with the Kindle Fire kernel I had found a very helpful information page on the internal parts of the device, with very detailed information - it was really helpful. I know that with these generic Chinese tablets finding such info may be much more difficult due to lack of interest and lack of popularity when compared to major brand tablets such as the Kindle Fire - but if anyone out there has ran across similar information it would give us GREAT progress in developing an ICS ROM for the 910. Here is a link to the breakdown of components in the Kindle Fire:
http://www2.electronicproducts.com/Amazon_Kindle_Fire_D01400_Tablet-whatsinside_text-123.aspx
The thread to the ICS ROM for Pacal 2 (rk2918) device is here: http://forum.xda-developers.com/showthread.php?t=1734181
A big thanks to Vurrut for all of his work! Hopefully we can use parts of his ROM to get ICS running on our Lanyu/Airpad!
Pls open a terminal, type "dmesg" and upload the log. Then we will see
If you have luck your build has also the kernel config file. You will find it under /proc/config.gz.
- Oma -
Oma7144 said:
Pls open a terminal, type "dmesg" and upload the log. Then we will see
If you have luck your build has also the kernel config file. You will find it under /proc/config.gz.
- Oma -
Click to expand...
Click to collapse
Do you honestly think I would be working on a Linux kernel without a knowledge of the existence of dmesg or config.gz? Did you also forget to remind me of adb shell logcat -d >> logcat.log ?
Sent from my A100 using xda premium
linuxsociety said:
Do you honestly think I would be working on a Linux kernel without a knowledge of the existence of dmesg or config.gz? Did you also forget to remind me of adb shell logcat -d >> logcat.log ?
Click to expand...
Click to collapse
Sry. You've been asking for touch, sensors etc.. In the named logs you will find all that.
- Oma -
Oma7144 said:
Sry. You've been asking for touch, sensors etc.. In the named logs you will find all that.
- Oma -
Click to expand...
Click to collapse
Only partial information can be obtained in this manner as it will only show what device modules are loaded, the information I was wanting was precise model information of the chipsets used in the tablet. And the config for the stock kernel is not included in procfs anyway as the developers must have not said =Y to CONFIG_IKCONFIG
Sent from my A100 using xda premium
]
Code:
CONFIG_INPUT_TOUCHSCREEN=y
# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
# CONFIG_TOUCHSCREEN_AD7879 is not set
# CONFIG_I2C_LZ300 is not set
CONFIG_I2C_LZ300_ST=y
# CONFIG_I2C_SIS809 is not set
# CONFIG_INPUT_MISC is not set
CONFIG_INPUT_GPIO=y
#
# Magnetometer sensors
#
# CONFIG_COMPASS_AK8975 is not set
# CONFIG_COMPASS_AK8973 is not set
CONFIG_G_SENSOR_DEVICE=y
# CONFIG_GS_MMA7660 is not set
CONFIG_GS_MMA8452=y
# CONFIG_GS_L3G4200D is not set
# CONFIG_INPUT_JOGBALL is not set
# CONFIG_LIGHT_SENSOR_DEVICE is not set
With the Model (SIS809, MMA8452, AK8975 etc.) you have all what you need. This you will also find in the dmsg log.
That's enough to compile from sources.
Anyway.
- Oma -
Oma7144 said:
]
Code:
CONFIG_INPUT_TOUCHSCREEN=y
# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
# CONFIG_TOUCHSCREEN_AD7879 is not set
# CONFIG_I2C_LZ300 is not set
CONFIG_I2C_LZ300_ST=y
# CONFIG_I2C_SIS809 is not set
# CONFIG_INPUT_MISC is not set
CONFIG_INPUT_GPIO=y
#
# Magnetometer sensors
#
# CONFIG_COMPASS_AK8975 is not set
# CONFIG_COMPASS_AK8973 is not set
CONFIG_G_SENSOR_DEVICE=y
# CONFIG_GS_MMA7660 is not set
CONFIG_GS_MMA8452=y
# CONFIG_GS_L3G4200D is not set
# CONFIG_INPUT_JOGBALL is not set
# CONFIG_LIGHT_SENSOR_DEVICE is not set
With the Model (SIS809, MMA8452, AK8975 etc.) you have all what you need. This you will also find in the dmsg log.
That's enough to compile from sources.
Anyway.
- Oma -
Click to expand...
Click to collapse
Mr. Oma, I am sorry but I think you may be in the wrong thread, the Lanyu 910 only shares one thing in common with the other common RK2918 based tablets, and that is the RK2918 its self, the rest of the hardware that makes up the full system is different on the 910/Airpad than the more popular tablets that are using the RK2918. For example you probably use a RTL based wifi chip in the config you are using also, where the 910/AP uses the SWL-2480 which uses a Marvel 8686 driver in the linux kernel or you can use the libertas driver in more recent kernels. What exactly is the config you pasted here from? At this point I know the internal hardware enough to get a proper config file for the 910/Airpad, however there are compile issues with certain components and without resolving the compile issues there is no kernel image going to be generated unless I disable the problems at hand in the config, if you want more up-to-date information then head over the the x10 forums and check the original thread for 910/AP kernel development: http://forums.x10.com/index.php?topic=27184.0
Have you seen this?
Here is another Tab using SWL-2480 (looks like an Aoson M12).
Here is another 3.0.8 source, originally from a Chinese Tab named Xinboa.
Maybe that helps.
- Oma -
Oma7144 said:
Have you seen this?
Here is another Tab using SWL-2480 (looks like an Aoson M12).
Here is another 3.0.8 source, originally from a Chinese Tab named Xinboa.
Maybe that helps.
- Oma -
Click to expand...
Click to collapse
I appreciate your effort in helping me find info, but I have already researched most the possibilities and am already aware of the sites you linked. The problems aren't finding hardware specs, the problem now is getting 3.0.8 sources to compile with the Airpads hardware selected in the configuration, as I posted in the x10 forum, it doesn't appear that any 3.0.8 kernels have been successfully compiled for other devices using the same board-config as the 910, in fact the link you specified with the swl-2480 is the only device that has similar hardware aside from the rk2918 that I have found. The wifi and audio both fail to compile with Ody.se sources. I have decided to put most of my work now into testing/development of Jelly Bean for the Acer Iconia Tab, as it doesn't seem that many others are interested in the 910/Airpad development. Thanks again
Ok.
Odys-Xpress sources? That's kernel 2.6.32.27, isn't it?
But try the sources from above link. Could search for that
A library for Marvell 8686 SDIO WLAN devices.
So far, the following modules have been verified:
(1) Samsung SWL-2480
(2) Azurewave AW-GH321
(3) USI WM-G-MR-09
(4) Murata SP-8HEP-P
I don't know if they will compile.
- Oma -
Oma7144 said:
Ok.
Odys-Xpress sources? That's kernel 2.6.32.27, isn't it?
But try the sources from above link. Could search for that
A library for Marvell 8686 SDIO WLAN devices.
So far, the following modules have been verified:
(1) Samsung SWL-2480
(2) Azurewave AW-GH321
(3) USI WM-G-MR-09
(4) Murata SP-8HEP-P
I don't know if they will compile.
- Oma -
Click to expand...
Click to collapse
They won't compile with 4.2.0 or 4.4.0 arm eabi toolchain in 3.0.8 sources, i tried them, since 3.0.8 it has been replaced with libertas instead of mv8686, i've done looked into all of it man
linuxsociety said:
They won't compile with 4.2.0 or 4.4.0 arm eabi toolchain in 3.0.8 sources, i tried them, since 3.0.8 it has been replaced with libertas instead of mv8686, i've done looked into all of it man
Click to expand...
Click to collapse
Use gcc 4.5.2 or higher.
- Oma -
Oma7144 said:
Use gcc 4.5.2 or higher.
- Oma -
Click to expand...
Click to collapse
I also tried gcc 4.6.2 and 4.6.3 natively setup with cross compile in Gentoo / Funtoo - I get the same same errors with the wifi and the audio as using the appropriate eabi-arm toolchains.. I tracked down the problems though, it is a dephell with major code changes in common headers. The headers that are included in the sources have changed from 2.6.32.27 and to 3.0.8 and porting everything up to current is quiet more code changes than I am willing to work on. Like I have said though, I am no longer working on this kernel for the generic devices 910/AP, I have more work on my slate now than I need working on the Acer Vangogh / Vendetta kernels for Jelly Bean to incorporate Tiny HAL and newer tegra changes keeping compatability with the only Acer source we have available. But at least I am not limited to products that aren't following the GPL appropriately, and the use of uncommon hardware that makes debugging damn near impossible. I almost have the Vangogh board and Acer specifics ported over to 3.1's grouper from the nexus project and it's much more smoother than working with that chinese developed tab
Ok, than have a good time!
Greetings to Southern Kentucky.
- Oma -
linuxsociety said:
If anyone has the X10 airpad (rk2918 based) or the Lanyu 910 and has some important information regarding the internal hardware, please contact me with details, as I can probably get a working kernel for our device in a matter of hours.
Click to expand...
Click to collapse
Here you go: eboda-TS, MV8686 WLAN, MMA8452Q Sensor, WM8988 Audio, ANX7150 HDMI, HYM8563 Clock, APX192 Powermgt.
Could you pls compile a kernel?
- Oma -
I have a clones phone of CHERRY BURST / XOLO A500 / CROSS A28.
TeamBURST is working hard to make perfect cook roms, and I thanks to them.
But, I have some small wishes like TV out, OC,... my device, which need a custom kernel.
My friend have asked some developer about it but they said that they need a source code of my phone.
My phone is a Chinese phone and I can't find any source code of any clones have roms working on my phone.
Anyone can help me ? Please !
(Sory for my bad English)
Unfortunately you can't
thread closed
If you are a developer, and wish to have a device merged into Omni, here is the current "temporary" process to use. There are 2 ways to do this - make your tree available on github (or a similar service), or request a new git tree be created, and submit it to gerrit.
1) Get your device working. There's plenty of help available in #omnirom on Freenode if you need assistance. An AOSP device tree is probably the best place to get started.
2) Set up your device to use the OmniROM "custom" build type, rather than full/aosp. More information will follow on this step - check device/samsung/manta or device/lge/mako for an example.
3) Make your device tree available on github or a similar git service. Please retain authorship of an original tree (if you fork it from AOSP or another custom ROM)
4) Come to #omni on Freenode, and have a chat to one of the core developers (they are listed at the top of the user list) - they will be able to help you get your device merged
Please note, in order to add a new device, we will require a maintainer on an ongoing basis for it, to ensure someone is able to investigate bugs that users report on a device. Without this, we unfortunately cannot enable nightly builds for a device.
will a cm kernel tree work for the most part with just a few changes?
azoller1 said:
will a cm kernel tree work for the most part with just a few changes?
Click to expand...
Click to collapse
yes - of course it must be 10.2 (4.3)
most likly it will work even unchanged
pulser_g2 said:
3) Make your device tree available on github or a similar git service. Please retain authorship of an original tree (if you fork it from AOSP or another custom ROM)
Click to expand...
Click to collapse
Along these lines, do NOT remove copyright attributions of a changed file. You may ADD copyrights to a header, but do NOT remove anything.
maxwen said:
yes - of course it must be 10.2 (4.3)
most likly it will work even unchanged
Click to expand...
Click to collapse
Most likely kernel change will be that reverting out that MDP sync point mess used by CM's AOSP+CAF frankendisplay. Can't link to it from my current location.
I have everything device sided transformed to Omni (m7ul,m7-common,and msm8960) and have exactly this problem now. Builds fine but Stucks after a few secs booting and hard reboots. Already looked into kmsg with maxwen but now we need to find what's causing it...
Reverted some stuff (MDP) kernel sided but haven't succeeded so far. Would be appreciated if u point us there when u back on a pc
noNeedForAsig
TF300T
OK here goes..
For the Asus Transformer TF300T the kernel forked from the CyanogenMod github:
https://github.com/scanno/android_kernel_asus_tf300t/tree/android-4.3
And the device tree, modified to get OmniROM to finish the build and get a bootable result:
https://github.com/scanno/android_device_asus_tf300t/tree/android-4.3
Hopefully it will be added to the OmniROM github.
n3ocort3x said:
I have everything device sided transformed to Omni (m7ul,m7-common,and msm8960) and have exactly this problem now. Builds fine but Stucks after a few secs booting and hard reboots. Already looked into kmsg with maxwen but now we need to find what's causing it...
Reverted some stuff (MDP) kernel sided but haven't succeeded so far. Would be appreciated if u point us there when u back on a pc
noNeedForAsig
Click to expand...
Click to collapse
I'm thinking for m7ul it would be https://github.com/CyanogenMod/android_kernel_htc_m7/commit/f2efb02581110747711c8b17f31f38fc3ed5dd1a
Don't want to hijack the thread though, so we can probably discuss this elsewhere
@Grarak Maybe you should post your edited device tree for Omni Rom =)
Sent From my i9500 With ☆★Crash Rom★☆
AL_IRAQI said:
@Grarak Maybe you should post your edited device tree for Omni Rom =)
Sent From my i9500 With ☆★Crash Rom★☆
Click to expand...
Click to collapse
Already on my github
https://github.com/Grarak/android_device_samsung_i9500
kernel tree
https://github.com/Grarak/android_kernel_samsung_exynos5410
proprietary
https://github.com/Grarak/proprietary_vendor_samsung
exynos 5410 repos:
https://github.com/intervigilium/android_hardware_samsung_slsi_exynos5410
https://github.com/intervigilium/android_hardware_samsung_slsi_exynos
https://github.com/intervigilium/android_hardware_samsung_slsi_exynos5
https://github.com/intervigilium/android_hardware_samsung_slsi_exynos5-insignal
https://github.com/intervigilium/android_hardware_samsung_slsi_openmax
pretty much ^^
I'd like to maintain for l900 and i605 (Sprint and Verizon Galaxy Note 2).
device trees
https://github.com/omnirom-slickrick/android_device_samsung_l900 (sprint tree)
https://github.com/omnirom-slickrick/android_device_samsung_i605 (vzw tree)
https://github.com/omnirom-slickrick/android_device_samsung_t0lte (note 2 common tree)
https://github.com/omnirom-slickrick/android_device_samsung_smdk4412-common (same as tree on omnirom github but actually more updated and device settings added back)
kernel
https://github.com/omnirom-slickrick/android_kernel_samsung_smdk4412 (just have needed device settings commits added back in)
thracky said:
I'm thinking for m7ul it would be https://github.com/CyanogenMod/android_kernel_htc_m7/commit/f2efb02581110747711c8b17f31f38fc3ed5dd1a
Don't want to hijack the thread though, so we can probably discuss this elsewhere
Click to expand...
Click to collapse
we already making progress but it needs more work to be done.. at least we are now in system with working wifi, and display but modem doesent work.. something for tomorrow, and i dont want to hijack this thread too sorry if my question was in the wrong section but i thought i mention it because of the post above mine. nevermind i cann offer to maintain m7ul as already discussed with maxwen and oin IRC but a lot of work needs to be done:
here are my sources, device trees are usable but kernel needs more work as said above:
device trees:
https://github.com/n3ocort3x/android_device_htc_m7ul
https://github.com/n3ocort3x/android_device_htc_m7-common
https://github.com/n3ocort3x/android_device_htc_msm8960-common
kernel: its a modified one but its no problem to bring it back to stock features and will push as soon asap the modem stuff is sorted out
https://github.com/n3ocort3x/android_kernel_htc_m7
EDIT modem fixed, only BT left
@sykomaniac , look at first post and become a maintainer
pulser_g2 said:
If you are a developer, and wish to have a device merged into Omni, here is the current "temporary" process to use. There are 2 ways to do this - make your tree available on github (or a similar service), or request a new git tree be created, and submit it to gerrit.
1) Get your device working. There's plenty of help available in #omnirom on Freenode if you need assistance. An AOSP device tree is probably the best place to get started.
2) Set up your device to use the OmniROM "custom" build type, rather than full/aosp. More information will follow on this step - check device/samsung/manta or device/lge/mako for an example.
3) Make your device tree available on github or a similar git service. Please retain authorship of an original tree (if you fork it from AOSP or another custom ROM)
4) Post a link here to the device tree (and kernel repository) for review, and tell us what device it is (give model numbers and board names and as many details as possible )
Click to expand...
Click to collapse
We have quite a few things that aren't working like bluetooth, camera is buggy, H/W vsync, gps, and fm radio.
https://github.com/SeannyM/android_device_samsung_kylessopen
https://github.com/SeannyM/ba2x-kernel
gt-s7560m with quadband gsm and 850/1900/2100 WCDMA/UTMS
We have a MSM7227a cpu armv7 clocked at 1008mhz stock.
645mb of usable ram
4gb of storage with 1.7 usable
233 dpi 800x480 4inch screen
Adreno 200 enhanced
5mp camera 1.3 front facing
hopefully we can get something official
single sim
Gtab2 10.1 Wifi & 3G (p5110 & p5100)
There you have my device tree for omni
p5110 :
https://github.com/sevenup30/android_device_samsung_p5110
p5100:
https://github.com/sevenup30/android_device_samsung_p5100
omap4-common (had to edit it cuz of duplicate libion entry):
https://github.com/sevenup30/android_device_samsung_omap4-common
other dependencies required from CM & Themuppets
kernel :
https://github.com/CyanogenMod/android_kernel_samsung_espresso10
samsung proprietary:
https://github.com/TheMuppets/proprietary_vendor_samsung
samsung hardware:
https://github.com/CyanogenMod/android_hardware_samsung
apps samsung service:
https://github.com/CyanogenMod/android_packages_apps_SamsungServiceMode
Everything is working (sound / wifi / bluetooth / video playback) BUT!
I must edit build.prop by hand to get sound working until omni build process take care of "product_build_prop_overrides" into custom_XXXX.mk
see:
http://forum.xda-developers.com/showthread.php?t=2484747
Original Samsung Galaxy Note
Samsung n7000 initial bringup:
Modified CM n7000 device: https://github.com/chasmodo/android_device_samsung_n7000/tree/android-4.3
Modified CM galaxys2-common: https://github.com/chasmodo/android_device_samsung_galaxys2-common/tree/android-4.3
CM smdk4412 kernel: https://github.com/CyanogenMod/android_kernel_samsung_smdk4412/tree/cm-10.2
Samsung proprietary stuff: https://github.com/TheMuppets/proprietary_vendor_samsung/tree/cm-10.2
Samsung hardware tree untouched from OmniRom.
Device info:
Board platform - exynos4
SOC - exynos4210
Board name - smdk4210
Kernel specifics - unified kernel and recovery
It compiles fine using the repos listed above, but throws up a kernel assert error when flashing the Rom. Several compilers for different devices complained about it in the 'All the answers' thread. The way out of this is to flash a CM10.2 kernel immediately after the Rom flash aborts, then Omni boots up fine.
What works:
1. telephony
2. mms
3. WiFi
4. GPS
What doesn't work:
1. data
2. bluetooth turns off as soon as you turn it on
3. both sdcards are invisible from Android; all your stuff is there when you drop into recovery, though
4. Settings/Storage FC when tapped - see #3
5. Performance options also FC
6. Notification drawer cannot be pulled down
Camera cannot be tested because it shuts down as soon as you start it, saying: "No external storage available" - again, see #3
Galaxy Note II / N7100 (International)
Samsung Galaxy Note II / N7100 Bring up details.
I have a working build of the Omni rom for the N7100. Below are the details on what is working and not working. i have been using it for the last 2 days, so far not crashes or reboots all seems to be working fine. i cherry picked a few commits and included it into my build
Working :
WIFI
DATA -3G & 2G
Telephony & MMS & SMS
GPS
Sound
Camera (Both Front and Back)
SD card
Performance control
Notification drawer & Lights
Multi-Window
roadrunner
Not Working :
BT
Backlights(if i install a custom kernel then the lights work)
Device Tree for N7100 - https://github.com/tilaksidduram/device_samsung_n7100
Device smdk4412-common - https://github.com/tilaksidduram/android_device_samsung_smdk4412-common
smdk-4412 Kernel (3.0.100) - https://github.com/CyanogenMod/android_kernel_samsung_smdk4412
samsung hardware - https://github.com/CyanogenMod/android_hardware_samsung
DEVICE: GT-N7100
sources
https://www.github.com/UtkarshGupta/android_device_samsung_n7100
https://www.github.com/omnirom/android_device_samsung_smdk4412-common
https://www.github.com/omnirom/android_hardware_samsung
https://www.github.com/omnirom/android_kernel_samsung_smdk4412
https://www.github.com/TheMuppets/proprietary_vendor_samsung
Is anyone else working on d2att/d2can (Galaxy S3 I747)? I'm not overly familiar with ROM development, but I can compile CM10.2 for this device just fine, and I'm slowly working on getting Omni to compile for it as well. If someone more experienced than I is already working on it though, I'll probably just let them do it.
If I am the only one, expect some newb-ish questions in the near future.
dstruct2k said:
Is anyone else working on d2att/d2can (Galaxy S3 I747)? I'm not overly familiar with ROM development, but I can compile CM10.2 for this device just fine, and I'm slowly working on getting Omni to compile for it as well. If someone more experienced than I is already working on it though, I'll probably just let them do it.
If I am the only one, expect some newb-ish questions in the near future.
Click to expand...
Click to collapse
I think a few are... There has been chat of it in the IRC channels.
Device name: LG Optimus 4X HD
Codename: P880
Board name: X3
Chipset: Tegra 3 AP33
Everything works, except button backlight.
https://github.com/Adam77Root/android_device_lge_p880
https://github.com/Adam77Root/android_kernel_lge_x3
https://github.com/TheMuppets/proprietary_vendor_lge
Code:
#include
/*
* I am not responsible for bricked devices, dead SD cards, thermonuclear
* war, or the current economic crisis caused by you following these
* directions. So don't be an *** ****
*/
hi.. i'm already started make some modifications on ROM with other Brazilian DEV's for "Evertek S.A - SKMtek Genesis Tab GT7305"... we already found the source kernel from another Netbook or Development Board PC who uses the same SOC... but nothing already have been maked to kernel, we use the provided kernel from stock (Kernel 3.4.5+)... and about the ROM we already have two custom ROM's... One is Stock Modded (4.2.2) and another is KitKat Ported ROM from another Evertek Device... *Portuguese-Brazil Language Site/Forum
And we already make some modifications to this KK port...
- ROOT
- BusyBox
- Init.D support
- Build.Prop Mods
- SuperUser
- zipalign apps after boot
.. and other mods.
we already make too much on ROM but nothing about kernel... we want make a better kernel with optimizations and a better TCP/Clock Table, More Governors , More I/O Scheduler and maybe Overclock to 1600mhz to start after have a custom Kernel booting...
Now we need someone who understand about recovery's like CWM or TWRP and Kernel Compilation better than me to we can start make something awesome =D i think this can be used to another company's/Chinese tablets too, using the same SOC (WM8880) evidently... . . . (Found^^Working^^Recovery's)
i can't start testing here because if i flash this kernel using the Stock Recovery (WonderMedia Recovery tool) maybe i can possible brick my tablet... so if someone understand about CMW recovery to start would be nice =D
Update Progress / ChangeLog ¬
Code:
# 25/12:
- [STRIKE]Found Possible match [URL="http://forum.xda-developers.com/showthread.php?t=2305268"]CWM port[/URL] from [URL="http://forum.xda-developers.com/showthread.php?t=2216390"]Asus MeMo Pad 7{ME172V}[/URL] on XDA Forum[/STRIKE] #NOPE...
- FOUND WOKING [URL="http://blog.hadi-cpu.com/2013/09/cwm-recovery-6036-w8850-rc2.html"]CWM Recovery[/URL] from Malasya Blog from Generic WM8850 SOC tablet , Founded [URL="http://blog.hadi-cpu.com/2013/10/twrp-touch-wondermedia-wm8850-jb-version.html"]TWRP recovery[/URL] too but not tested (Thanks to #Rollidark to notify me about and #osinaldi to discover that from malasya blog) [Mirrors -> [URL="https://www.4shared.com/rar/2POyc0B0ba/CWM_WM8850_NSFAT-RC2.htm?sop=true"]CMW[/URL] -> [URL="https://www.4shared.com/rar/rJBfUTQF/TWRP-JB-NSFAT-WM8850.htm"]TWRP[/URL]] // [URL="https://www.facebook.com/groups/NewSmartFrenAndroTab/"]Facebook Group of Recovery Developers[/URL]
- Studying some way to introduce the missing Touch driver to kernel from [URL="https://gist.github.com/psachin"]psachin Github[/URL]|[URL="http://cdn.liliputing.com/wp-content/uploads/2013/01/rock_02.jpg"]apc-rock-II-[/URL]|[URL="https://github.com/psachin/apc-rock-II-kernel"]kernel[/URL] how already modded the Source to work with [URL="http://tinyurl.com/oqxmuam"]Generic Netbook[/URL] who uses the same SOC
-- Merry Christmas to #ALL
# ?? to 23~24/12:
- ROM JB and KK + ADV. Patch developed by Brazilian Dev's team
- found Source Kernel to WM8880 SoC
Brazilian Developers who already help this projects from forum - genesiseries :
Code:
# KK ROM:
- #paulomsilva2006 {KitKat ROM Port}
- #Rollidark {KitKat Patch}
- #Wcfuria
- #? - Pedro Alves
- #? - Pedro Victor
- #? - Walter Moretti
- #? - Moises Teixeira
Code:
# JB Stock ROM:
- #ylukasy {ROM Dev.}
- #Rollidark
- #paulomsilva2006
- +?
if i forget someone.. please comment below :highfive:
Reserved
wow there's only a handful on and off development going on for this SoC, I still keep my WM8880 tablet just in case somebody made a breakthrough in doing Custom ROM or even getting real ubuntu/debian to boot natively... are you still on this?
funtikar said:
wow there's only a handful on and off development going on for this SoC, I still keep my WM8880 tablet just in case somebody made a breakthrough in doing Custom ROM or even getting real ubuntu/debian to boot natively... are you still on this?
Click to expand...
Click to collapse
just a few Brazilian and Malasya Developers still make progress with this SoC... if you want to try install the custom ROM´s i have shared upper topic.. it will be by your won and I am not responsible for bricked devices...
i´m already started make progress with Custom Kernel but i need found the touch screen driver source and re-work the sound driver(Alsa Drivers...) and compile the recovery with kernel too.. to than have some trust on my work to flash it on tablet =#
:highfive:
DvDwx. said:
just a few Brazilian and Malasya Developers still make progress with this SoC... if you want to try install the custom ROM´s i have shared upper topic.. it will be by your won and I am not responsible for bricked devices...
i´m already started make progress with Custom Kernel but i need found the touch screen driver source and re-work the sound driver(Alsa Drivers...) and compile the recovery with kernel too.. to than have some trust on my work to flash it on tablet =#
:highfive:
Click to expand...
Click to collapse
meh, its my rom testing ground anyway not really worried .. i actually have the tablet connect directly from the battery wires(the battery removed) to the adapter(usb)... anything is better than nothing for the development hehe...wait by Malasya do u mean Malaysia? whos that developer lol..
funtikar said:
meh, its my rom testing ground anyway not really worried .. i actually have the tablet connect directly from the battery wires(the battery removed) to the adapter(usb)... anything is better than nothing for the development hehe...wait by Malasya do u mean Malaysia? whos that developer lol..
Click to expand...
Click to collapse
i mean Malaysia.. the country... because i don't have found the real developer.. only the Facebook's group where it have been shared... i write too fast and don't check if i write it correct too...
--
i Already compile the kernel with CMW recovery and flashed on tablet ... but i need find the Touchpad driver to make he work properly... i stay getting some other minor issues on logcat/kmsg reports...
but i already test four touch drivers and anyone works... only OTG stay working.. that is the problem on developing the kernel without the official source release by the producer company... maybe i will need close this developing project because that =/
DvDwx. said:
i mean Malaysia.. the country... because i don't have found the real developer.. only the Facebook's group where it have been shared... i write too fast and don't check if i write it correct too...
--
i Already compile the kernel with CMW recovery and flashed on tablet ... but i need find the Touchpad driver to make he work properly... i stay getting some other minor issues on logcat/kmsg reports...
but i already test four touch drivers and anyone works... only OTG stay working.. that is the problem on developing the kernel without the official source release by the producer company... maybe i will need close this developing project because that =/
Click to expand...
Click to collapse
what a coincidence , I was wondering today when you will reply lol
ah I see too bad, maybe you will share it at techknowme forum, ... wow Malaysian ?, Im asking because I'm Malaysian, can you pm me the link where its shared?
DvDwx. said:
i mean Malaysia.. the country... because i don't have found the real developer.. only the Facebook's group where it have been shared... i write too fast and don't check if i write it correct too...
--
i Already compile the kernel with CMW recovery and flashed on tablet ... but i need find the Touchpad driver to make he work properly... i stay getting some other minor issues on logcat/kmsg reports...
but i already test four touch drivers and anyone works... only OTG stay working.. that is the problem on developing the kernel without the official source release by the producer company... maybe i will need close this developing project because that =/
Click to expand...
Click to collapse
please continue developing this project..i have using acer b1 740 and it dont have android 4.4 update
tuyenat3 said:
please continue developing this project..i have using acer b1 740 and it dont have android 4.4 update
Click to expand...
Click to collapse
man... i just don't want blame anyone but... to we can do something to your tablet we need the kernel source and that don't stay open to developers... on this Chinese tablets we have some little configurations to can work with... but the custom kernel project i need to abandon for two reasons... first i don't have much time to can work to create a stable and functional custom kernel to everyone... second i don't have a kernel source compatible with tablets... what i found is from a electronics engineering Project computer Board ... and to it can fit on tablet is missing too much drivers compatibles with to can work smoothly and functional... someday if i found a new source maybe i can try comeback developer something to that =#
please continue developing this project
I use a genesis 7305 his kernel is very poorly optimized would like to make this usable tablet sorry for my bad English I use Google translator ;-;
2021... I tried to put a Chinese rom, but I brick the tablet, it only responds to fastboot, when I put the sudo command fastboot flash:raw boot uzImage.bin ramdisk.bin and plug in the charger and press power it appears a genesis screen.
Boot FOSSEE-OS from SCARD | FOSSEE-Laptop
laptop.fossee.in
GitHub - FOSSEE/FOSSEE-netbook-kernel-source: A low cost fossee-laptop based on wm8880 ARMv7 SoC
A low cost fossee-laptop based on wm8880 ARMv7 SoC - GitHub - FOSSEE/FOSSEE-netbook-kernel-source: A low cost fossee-laptop based on wm8880 ARMv7 SoC
github.com
THIS INFO IS FOR ARMv7 ONLY:
*Broadcom
*Mediatek
*Speadtrum (vivalto)
*Qualcomm
*Tegra
Moderators please don't close this thread I will make typos after returning from school
This thread will more be helpful for ppls
BROADCOM
REQUIREMENTS:
1. Need kernel source if in case to make more stability
2. BCM21654 and above
SOURCES
KERNEL: ----> Note this contains the things which are to make some features to work on ROMs
https://github.com/karthick111/bcm21654-cm_kernel_common
DEVICE_TREE: ----> Can have the reference or port but give credits if it is based on any of it
GALAXY POCKET NEO: https://github.com/karthick111/android_device_corsica_cm
GALAXY FAME: https://github.com/wulsic/android_device_samsung_nevisp
GALAXY GRAND: https://github.com/pawitp/android_device_samsung_i9082
PATCHES: ----> All major patches from #Pawitp
KITKAT: https://github.com/wulsic/android_patchesnevisp
LOLLIPOP: https://gist.github.com/pawitp/cba169c87dba57eea8ef
COMMON-KITKAT: (hardware/libhardware/include/audio.h) replace with this->: https://gist.github.com/dhinesh77/7206ec7900bee32e4c51 ----> For working mic,videocam fix
COMMON-KITKAT,LOLLIPOP: https://github.com/PAC-man/android_frameworks_native/commit/0c81fda74f6e7f9dc5f48bd00e4dbeaef12fdbc2 ----> EGL patch
COMMON-LOLLIPOP: https://gist.github.com/Flex1911/47a9515fc482d5551a85 ---> patch for icu to run the old egl to run on new framework
________________________END FOR BROADCOM________________________
MediaTEK
SOURCES AS FAR WE KNOW MEDIATEK VIOLATING GPL TERMS SO WE CANT EXPECT KERNEL'S
DEVICE_TREE: ----> Can have the reference or port but give credits if it is based on any of it
MT6575 -single,dual core variants
CELKON A98: https://github.com/karthick111/android_device_Celkon_A98
________________________WAIT FOR NEXT UPDATE MEDIATEK________________________
SPEADTRUM Socs
SOURCES SPEADTRUM KERNEL SOURCE'S ARE RELEASED BUT SOME ARE NOT WORKING
WARNING IN THIS CHIPSET RIL FIXES ARE NO WAY SO QUIT IT IF YOU DONT HAVE WIFI
DEVICE_TREE: ----> Can have the reference or port but give credits if it is based on any of it
SAMSUNG GALAXY V SM-G313HZ: https://github.com/cleverior/android_device_samsung_vivalto3gvndx Used patches are in the device tree itself
SAMSUNG GALAXY STAR: https://github.com/TeamRegular/android_device_samsung_mint
________________________END FOR SPEADTRUM________________________
clicking the THANKS button may appreciate me to finish the guide
Could we port CM11 from an MTK to another with this?
karthick mostwanted said:
THIS INFO IS FOR:
*Broadcom
*Mediatek
*Speadtrum (vivalto)
*Qualcomm
*Tegra
Moderators please don't close this thread I will make typos after returning from school
This thread will more be helpful for ppls
Click to expand...
Click to collapse
Kindly share how to please I got kernel sources for my device
Yes for sure but wait I'm unable to amend some time for it
karthick mostwanted said:
Yes for sure but wait I'm unable to amend some time for it
Click to expand...
Click to collapse
Take your time
karthick mostwanted said:
Yes for sure but wait I'm unable to amend some time for it
Click to expand...
Click to collapse
Where is the method? How to port or create from existing tree?
The simple method can be done by all and it's no way useful and its not explainable
If you are new to this quit it let other devs make use if it