Database Info

[Q] xperia miro possible hard brick?

so... i flashed 11.0.a.5.5 but i forgot to root it, so i downloaded some older firmware. unluckily, something was wrong with that file and i got dump ram message. so... i downloaded other version of firmware and flashed. then, when i tried to turn it on, only green light would few time blink and that was all. so i tried to flash again with that same firmware. and now - when i try to turn it on, nothing happens. tried to turn it in flash mode - nothing. fastboot mode - nothing. something that gives me hope - when i plug it in computer, it detects that something is plugged in, but beside that - nothing happens

maybe battery is dead? it charges when you plug in charger?
Στάλθηκε από το Xperia Tipo μου χρησιμοποιώντας Tapatalk 2

i connected it through the night. no led turned on, or anything.
dead?

Maybe you should charge the battery in some other phone or universal charger and then try to get into flashmode.
Sent from my ST23i

remove your battery
open flash tool
start flashing
connect the phone without battery in flash mode (do not remove your finger from flash mode button) when flashtool prompts you
and then load your battery and remove finger from flash mode button
it will solve the problem

Naney said:
remove your battery
open flash tool
start flashing
connect the phone without battery in flash mode (do not remove your finger from flash mode button) when flashtool prompts you
and then load your battery and remove finger from flash mode button
it will solve the problem
Click to expand...
Click to collapse
it didn't. i'll give it another try with another battery.
thanks guys for helping me :highfive:

DUIRduje said:
it didn't. i'll give it another try with another battery.
thanks guys for helping me :highfive:
Click to expand...
Click to collapse
did you try it
did it work

Flash it online, maybe it will work bro

FajarMF28 said:
Flash it online, maybe it will work bro
Click to expand...
Click to collapse
i don't get it
@Naney
no, it didn't work

DUIRduje said:
i don't get it
@Naney
no, it didn't work
Click to expand...
Click to collapse
it must work bro
i think u did a little mistake
describing again
remove your miro's battery and do not install it
open flashtool and start flashing
when flashtool prompts you, connect the mobile phone without battery in flash mode (pressed volume down button or whatever it is)
i made it lots of time with tipo and every time worked..
good luck..

Have you unlocked your bootloader? If not repair it in PC Companion.

same problem
DUIRduje said:
so... i flashed 11.0.a.5.5 but i forgot to root it, so i downloaded some older firmware. unluckily, something was wrong with that file and i got dump ram message. so... i downloaded other version of firmware and flashed. then, when i tried to turn it on, only green light would few time blink and that was all. so i tried to flash again with that same firmware. and now - when i try to turn it on, nothing happens. tried to turn it in flash mode - nothing. fastboot mode - nothing. something that gives me hope - when i plug it in computer, it detects that something is plugged in, but beside that - nothing happens
Click to expand...
Click to collapse
dude i have the same problem with the same device , would u please tell me how u fixed it ?? thanks

francois90 said:
dude i have the same problem with the same device , would u please tell me how u fixed it ?? thanks
Click to expand...
Click to collapse
i brought it to service. they thought that motherboard failed and replaced it. by some luck they didn't get what actually happened. and everything was covered by guarranty
:victory:

Naney said:
remove your battery
open flash tool
start flashing
connect the phone without battery in flash mode (do not remove your finger from flash mode button) when flashtool prompts you
and then load your battery and remove finger from flash mode button
it will solve the problem
Click to expand...
Click to collapse
not work, my phone hard brick, help any solutions

Ermm..

xperia L frozen !!!! help !

Hi there
I had to flash my xperia L with clean and tweaked rom downloaded from here http://forum.xda-developers.com/showthread.php?t=2419042
I had not enough charge on my battery and suddenly my phone shutdown and frozen. I am tired to pressing vol+ and power button for restart my device, everytime i got only one vibration but no display will appears.
Help me guys

s0ur0v said:
Hi there
I had to flash my xperia L with clean and tweaked rom downloaded from here http://forum.xda-developers.com/showthread.php?t=2419042
I had not enough charge on my battery and suddenly my phone shutdown and frozen. I am tired to pressing vol+ and power button for restart my device, everytime i got only one vibration but no display will appears.
Help me guys
Click to expand...
Click to collapse
Did you try to charge it when its off (just push the charger and wait)? Wait like 20-30 minutes and then try to power it on. If you see the kernel logo just go to CWM and reflash rom,if not try to use flashtool and some .ftf(4.1.2/4.2.2).

did u use c'n't on latest version 4.2.2 or older version??
.
.
if u used in 4.2.2 then it happened bec c'n't is based on old rom ie,4.1 so u may have to flash latest fw using flashtool

siankatabg said:
Did you try to charge it when its off (just push the charger and wait)? Wait like 20-30 minutes and then try to power it on. If you see the kernel logo just go to CWM and reflash rom,if not try to use flashtool and some .ftf(4.1.2/4.2.2).
Click to expand...
Click to collapse
i had to wait minimum 1 hour before try power button. but my phone didn't showing any logo or display. just light indicator glowing red.

shahiz369 said:
did u use c'n't on latest version 4.2.2 or older version??
.
.
if u used in 4.2.2 then it happened bec c'n't is based on old rom ie,4.1 so u may have to flash latest fw using flashtool
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2419042 i am using this rom,. i think this one is 4.1

s0ur0v said:
i had to wait minimum 1 hour before try power button. but my phone didn't showing any logo or display. just light indicator glowing red.
Click to expand...
Click to collapse
Did you try to flash ftf in flashtool,maybe you can put the phone in flashmode? Best way is if you got friend with same phone,or just same battery and try to power it on.And after that you will know if the phone is bricked or just the battery is empty.
But first try with Flashtool and maybe Sony flashtool.
Good luck.

shahiz369 said:
did u use c'n't on latest version 4.2.2 or older version??
.
.
if u used in 4.2.2 then it happened bec c'n't is based on old rom ie,4.1 so u may have to flash latest fw using flashtool
Click to expand...
Click to collapse
siankatabg said:
Did you try to flash ftf in flashtool,maybe you can put the phone in flashmode? Best way is if you got friend with same phone,or just same battery and try to power it on.And after that you will know if the phone is bricked or just the battery is empty.
But first try with Flashtool and maybe Sony flashtool.
Good luck.
Click to expand...
Click to collapse
yap, i did this way too. my brother has same handset. but i am unable to connect with flashtool . only red indicator glowing when i connect with a charger or data cable

Tutorial: Fix Xperia C softbrick with red led and no Sony logo

Fix Xperia C Red Light brick
Are you facing that the red led on your device blinks and there is no other signs of life? Then you are in the correct thread, I faced this issue when flashing a corrupted recovery but then I found out a easy way to fix it without opening the device or sending it in to Sony.
Requirements:
Xperia C with red light softbrick
MicroUSB Cable
Sony Update Service
Click to expand...
Click to collapse
1. The first thing you need to do is to make sure that you have downloaded Sony Update Service and have installed it onto your PC from the link above, if not, do it now.
2. Now launch Sony Update Service and select Xperia C in the list and then press Next.
3. Hold the Volume Up button and plugin microusbcable while doing so, if that doesn't work for you, hold power + volume up and plugin the microusbcable while doing. Keep holding button combination for a few seconds and wait for a green light on your phone, if it appears check on
your PC so that it's detected.
4. Wait while the firmware is being downloaded and reinstalled on your phone and enjoy your working device!

Have tried this on my bricked xperia c red led
Few weeks back no success
Logic
If you flash wrong recovery there is no way to boot in any mode
I can say this with 100% confident as I had spent full 3 days and tried every thing...
If u wona check goto custome mod for xperia c thred and get recovery installed
Then try this and share results
All the best

chauhanjayc said:
Have tried this on my bricked xperia c red led
Few weeks back no success
Logic
If you flash wrong recovery there is no way to boot in any mode
I can say this with 100% confident as I had spent full 3 days and tried every thing...
If u wona check goto custome mod for xperia c thred and get recovery installed
Then try this and share results
All the best
Click to expand...
Click to collapse
I flashed a faulty recovery using mobileuncles and there was no signs of life other than a red led liggt, and holding power + volume up works just fine and it went into flashmode.

I have the same issue.
I organized xperia light rom for our xperia c, I flashed it from custom recovery. Phone is completely dead now.
There is a just red light, phone does not go into download or fastboot mode. Pc Companion, Sony Update Center, Wmshua Flashtool do not recognize the phone.
Any suggestion with that?
I don't have warranty, my last option is to pay money for technical service.

this worked for me but instead of POWER+VOL UP i used POWER+VOL DOWN

thanks
thank, i like this forum

worth to try... (hope it won't happen to me :laugh: )

I have experienced this too, however, instead of using the Sony Update Service, I used the Sony PC Companion. At first it was not working, so I did a hard reset on the phone (press the button at the back). I held the power+up button while inserting the cable, and finally it was detected by Sony. It will reset your device to factory settings though.

seiferfury said:
I have experienced this too, however, instead of using the Sony Update Service, I used the Sony PC Companion. At first it was not working, so I did a hard reset on the phone (press the button at the back). I held the power+up button while inserting the cable, and finally it was detected by Sony. It will reset your device to factory settings though.
Click to expand...
Click to collapse
How did it
How Catch 4 buttons simultaneously
Please reply to the importance of

Im in the same scenario.. I tried all the procedures here but i failed.. I noticed that when i connect it, it disconnects after a while along with blinking of led light then reconnect again. And my PC detects it as unknown device.. I tried to install ADB driver but it also fails. Please help me.. Thanks. Sorry about my English

zergmac023 said:
Im in the same scenario.. I tried all the procedures here but i failed.. I noticed that when i connect it, it disconnects after a while along with blinking of led light then reconnect again. And my PC detects it as unknown device.. I tried to install ADB driver but it also fails. Please help me.. Thanks. Sorry about my English
Click to expand...
Click to collapse
If you flash a different device's rom, it happens. If you replace your motherboard, it will work again.

(
TacoNikky said:
If you flash a different device's rom, it happens. If you replace your motherboard, it will work again.
Click to expand...
Click to collapse
Which probably crying::crying::crying:

yeubeo168 said:
Which probably crying::crying::crying:
Click to expand...
Click to collapse
I have bought motherboard from china http://www.yoybuy.com/en/show/37431065583/ from this seller.
It took 20 days to arrive to Turkey. I have changed my motherboard and my phone is back right now :victory:
It works like a charm. Model number changed, it shows s39h but phone works like old days :good:

A detailed guide :
http://forum.xda-developers.com/sony-xperia-c/general/how-to-install-restore-stock-android-t2832005

It worked!!!!!
GethPrime said:
Fix Xperia C Red Light brick
Are you facing that the red led on your device blinks and there is no other signs of life? Then you are in the correct thread, I faced this issue when flashing a corrupted recovery but then I found out a easy way to fix it without opening the device or sending it in to Sony.
Requirements:
1. The first thing you need to do is to make sure that you have downloaded Sony Update Service and have installed it onto your PC from the link above, if not, do it now.
2. Now launch Sony Update Service and select Xperia C in the list and then press Next.
3. Hold the Volume Up button and plugin microusbcable while doing so, if that doesn't work for you, hold power + volume up and plugin the microusbcable while doing. Keep holding button combination for a few seconds and wait for a green light on your phone, if it appears check on
your PC so that it's detected.
4. Wait while the firmware is being downloaded and reinstalled on your phone and enjoy your working device!
Click to expand...
Click to collapse
It worked for my Xperia M (rooted on JB 4.3) with a locked bootloader which was STUCK on bootloop screen and when I did the whole thing with holding the power and volume up button (after I let the battery die after so many bootloops it did), FINALLY I was able to take it to flashmode, while I had selected from Sony PC Companion to repair my phone, and after 3-4 tries, I DID IT!!! Thank you so much for this thread ( I DEFINITELY pressed the "thanks" button), it really SAVED ME time and money (because I was planning to send it to Sony to fix it and you ALL know how bastards Sony is)!!!! And to all those of you who are DESPERATE to fix their phone (I hope you read this thread), DON'T PANIC, and DON'T GIVE UP!!! It took me 2 days of searching the web, and FINALLY I MADE IT!!! There are ALWAYS solutions to these kinds of problems!!!!

red light
dear friends please help me. I wanted to install cwm recovery with mobile uncle tools. when I placed recovery.img to phone memory(not in any folder), it didn't find the file, but when in sd card(not in any folder) it succesfully find. I selected and flashed, but the phone shut down and didn't start anymore. yesterday, when plugging to charge the red light under the screen was blinking. but today, it just stays on, not blinking, but after some time, goes off again, and start blinking. when I connect to PC, first it connects, after some time connection is lost and green light passes to red again, after some time it again connects. I tried Sony Update Service and PC Companion, didn't work. Please help...

Need help
same here only red light is blinking,,,i tried doing Power+vol up and Power+vol down and by inserting cable also...it just show a red light when plugged in

i'm also having the same problem....somebody please help!!!!really need to use it
kamran.kerim said:
dear friends please help me. I wanted to install cwm recovery with mobile uncle tools. when I placed recovery.img to phone memory(not in any folder), it didn't find the file, but when in sd card(not in any folder) it succesfully find. I selected and flashed, but the phone shut down and didn't start anymore. yesterday, when plugging to charge the red light under the screen was blinking. but today, it just stays on, not blinking, but after some time, goes off again, and start blinking. when I connect to PC, first it connects, after some time connection is lost and green light passes to red again, after some time it again connects. I tried Sony Update Service and PC Companion, didn't work. Please help...
Click to expand...
Click to collapse
i'm also having the same problem....somebody please help!!!!really need to use it

chauhanjayc said:
Have tried this on my bricked xperia c red led
Few weeks back no success
Logic
If you flash wrong recovery there is no way to boot in any mode
I can say this with 100% confident as I had spent full 3 days and tried every thing...
If u wona check goto custome mod for xperia c thred and get recovery installed
Then try this and share results
All the best
Click to expand...
Click to collapse
Does that mean phone is dead?

choxx said:
Does that mean phone is dead?
Click to expand...
Click to collapse
no all you need stock kernel
you can either google it or download ftf and check all except kernel
done

helpppp is it a hard brick?

My brother's htc sensation xe mob turned of suddenly and when tried to turn on mob it din't give anything only the soft button light and screen black .. he was using viper rom ..any idea about what happen with mob? P.s when i connect the mob to pc it give android phone but with yellow triangle and when try volume down with power button not give anyyhing too and soft button turn on and off simultaneously and when plug the charger while tge phone is off the led lamp give orange light for a sec then turn off again see screenshot

Ahmed.ragab said:
My brother's htc sensation xe mob turned of suddenly and when tried to turn on mob it din't give anything only the soft button light and screen black .. he was using viper rom ..any idea about what happen with mob? P.s when i connect the mob to pc it give android phone but with yellow triangle and when try volume down with power button not give anyyhing too and soft button turn on and off simultaneously and when plug the charger while tge phone is off the led lamp give orange light for a sec then turn off again see screenshot
Click to expand...
Click to collapse
I think luckily u havn't brick ur device.It is a hardware problem.

remove the battery and put it back
then try to boot into bootloader
if you boot select reboot

rzr86 said:
remove the battery and put it back
then try to boot into bootloader
if you boot select reboot
Click to expand...
Click to collapse
I can't boot into bootloader when i try thr soft key turn on and off simultaneously and screen is dark P.s (my brother put it in his pocket then he get it out to see it like that ? I thought maybe there is something wrong with screen but i tried to open mob normally till the soft key became light and never turn off then tried to make make a call to see if the mob will ring it said the mob is closed so i think this isn't about the screen any Idea ?

Any Idea ?
the 1st screenshot is when i connect my mob to the charger only soft key light on and never off
the 2nd screenshot is when I connected my mob to the pc and try to go to bootlooder with ADB
the 3rd screenshot is when i try to connect it with KGS utility (in all cases screen is always black)

Ahmed.ragab said:
Any Idea ?
the 1st screenshot is when i connect my mob to the charger only soft key light on and never off
the 2nd screenshot is when I connected my mob to the pc and try to go to bootlooder with ADB
the 3rd screenshot is when i try to connect it with KGS utility (in all cases screen is always black)
Click to expand...
Click to collapse
in adb mode your device is being recognized
when you are entering adb reboot bootloader what happens?

rzr86 said:
in adb mode your device is being recognized
when you are entering adb reboot bootloader what happens?
Click to expand...
Click to collapse
Nothing happen it's like the SS

Ahmed.ragab said:
Nothing happen it's like the SS
Click to expand...
Click to collapse
did you try to boot into safe mode?

rzr86 said:
did you try to boot into safe mode?
Click to expand...
Click to collapse
I can't boot into safe mode .. screen light never turned on and when i try to switch on mob normally thr green light turn on then turn off again and the mob vibrate and the soft key light always turn on anf after while it turn off and by just preesing volume up otlr power button it light again

Ahmed.ragab said:
I can't boot into safe mode .. screen light never turned on and when i try to switch on mob normally thr green light turn on then turn off again and the mob vibrate and the soft key light always turn on anf after while it turn off and by just preesing volume up otlr power button it light again
Click to expand...
Click to collapse
did you try to use a ruu.exe?
i am thinking that it could be a hardware issue

rzr86 said:
did you try to use a ruu.exe?
i am thinking that it could be a hardware issue
Click to expand...
Click to collapse
I'm trying to charge my battery more than 30 % cause he don't wanna continue installing and i have a slow external charger and will back to you again
It say rebooting to bootloader and stop in this stage see the SS

Ahmed.ragab said:
I'm trying to charge my battery more than 30 % cause he don't wanna continue installing and i have a slow external charger and will back to you again
It say rebooting to bootloader and stop in this stage see the SS
Click to expand...
Click to collapse
i don't know what to suggest anymore mate
probably it is hardware

rzr86 said:
i don't know what to suggest anymore mate
probably it is hardware
Click to expand...
Click to collapse
but do u think if it is a hardware it would read as android phone on pc normally but can't restart to bootloader ?

Ahmed.ragab said:
but do u think if it is a hardware it would read as android phone on pc normally but can't restart to bootloader ?
Click to expand...
Click to collapse
maybe some partition is damaged

rzr86 said:
maybe some partition is damaged
Click to expand...
Click to collapse
so how to repair this partitions ?

Ahmed.ragab said:
so how to repair this partitions ?
Click to expand...
Click to collapse
i really don't know mate
search here in xda
maybe you will find something about it
edit: did you try the unbricking project?
otherwise see this thread
http://forum.xda-developers.com/showthread.php?t=2775115

rzr86 said:
i really don't know mate
search here in xda
maybe you will find something about it
edit: did you try the unbricking project?
otherwise see this thread
http://forum.xda-developers.com/showthread.php?t=2775115
Click to expand...
Click to collapse
i tried unbricking project but ubuntu can't recognize my mob in QHSUSB_DLOAD mod without battery And ubuntu can't recognize my mob totally

rashmifantasy said:
I think luckily u havn't brick ur device.It is a hardware problem.
Click to expand...
Click to collapse
rzr86 said:
remove the battery and put it back
then try to boot into bootloader
if you boot select reboot
Click to expand...
Click to collapse
rzr86 said:
i really don't know mate
search here in xda
maybe you will find something about it
edit: did you try the unbricking project?
otherwise see this thread
http://forum.xda-developers.com/showthread.php?t=2775115
Click to expand...
Click to collapse
I repaired it guys the problem was with the lcd screen I replaced my sensation xe screen with my friends's sensation and it is working good now

Bricked my mate 7

I have a problem,i cant start up my phone it stuck on logo and it wont to turn up.
Phone is rooted but i dont install any custom rom..yet.
I dont install Cwm recovery and that is a big problem becouse i dont have acces to install rom or any update..
Can any one help me and tell me how to install Cwm recovery from sd card or how to install update or anything that will help me to turn on my phone..
I dont have computer so it would be nice if it be posible to fix this without comp. If is not..i will find computer..
Heelp pls
Sent from my GT-I9100 using XDA Free mobile app

jjoeshua said:
I have a problem,i cant start up my phone it stuck on logo and it wont to turn up.
Phone is rooted but i dont install any custom rom..yet.
I dont install Cwm recovery and that is a big problem becouse i dont have acces to install rom or any update..
Can any one help me and tell me how to install Cwm recovery from sd card or how to install update or anything that will help me to turn on my phone..
I dont have computer so it would be nice if it be posible to fix this without comp. If is not..i will find computer..
Heelp pls
Sent from my GT-I9100 using XDA Free mobile app
Click to expand...
Click to collapse
Try to do a factory reset.... turn off the phone.. and then press and hold volume up + power button for a few seconds until Huawei logo appears, release the buttons and the stock recovery should appear... then using the volume buttons go to factory reset and accept whit power button... and later reboot system