Database Info

[WIP] Unbricking evita

IF YOUR PARTITIONS NEVER APPEAR, THAT MEANS YOU WERE RUNNING THE 2.20 FIRMWARE AND FLASHED AN INCORRECT ROM AND BRICKED.. THERE IS NO FIX AT THIS TIME, PLEASE STOP ASKING ME HOW TO FIX IT.​
Reference threads​Users on 2.20 flashing IceColdJelly (a ROM for the endeavoru) have been bricked. This ROM effectively writes over mmcblk0p4, mmcblk0p5*, mmcblk0p6*, mccblk0p7* and then attempts to write mmcblk0p12 (which is our hboot, but fails due to write protection) (according to beaups' post in this thread http://forum.xda-developers.com/showthread.php?t=1960897, it overwrites mmcblk0p4, p5, p6 and p7)
http://forum.xda-developers.com/showthread.php?t=1963088
http://forum.xda-developers.com/showthread.php?t=1959497
http://forum.xda-developers.com/showthread.php?t=1727075 (heres a good reason NOT to flash CWM. This occurs when flashing it through Rom Manager, use TWRP instead!)
http://forum.xda-developers.com/showthread.php?t=1960022
As you can see. This clearly is an issue.
Enumerating your partitions​Q: What does enumerate mean?
A:
Code:
enumerate - to specify one after another.
Synonym: list
Prerequisites: Ubuntu 12.04 or higher. 32/64 bit
unbrick package: http://dl.dropbox.com/u/40181085/unbrick_evita.zip
A null p4: included in the unbrick package.. you will need to hex edit your IMEI into this file. the offset is 0x21c, it's after 11111111, which is the SuperCID
1. Open up 3 terminal windows
2. On your first window, type
Code:
$ watch -n.1 lsusb
3. Now, hold power down on your phone for about 10 seconds, and let go, Then go to your second window and spam
Code:
$ ls /dev/sd*
You should go from seeing this..
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
to seeing this...
4. Make note of the following.
for me, my devices was listed as /dev/sdb, yours may be listed as /dev/sdc or even /dev/sdd.
make note of /dev/sd*4 and /dev/sd*12
5. Make sure Linux sees the phone
Code:
$ sudo dmesg | grep "qcserial"
You should see "Qualcomm USB modem converter detected" as the last line of the output. If not, you can unplug and replug the USB cable or run...
Code:
$ sudo modprobe qcserial
to reload the driver
6. Reset the driver
Code:
$ sudo modprobe -r qcserial
7. create the block device
Code:
$ sudo mknod /dev/ttyUSB0 c 188 0
8. Open a third Terminal window and navigate to where you stored the Downgrade_evita folder. I saved it to my desktop, so my code is
Code:
$ cd Desktop/unbrick_evita
$ chmod +x emmc_recover
9. Now we restore the hboot.. replace /sdc12 with your device location that we discovered in step 3 and 4
Code:
$ sudo ./emmc_recover -f ./hboot_1.12.0000_signedbyaa.nb0 -d /dev/sdc12 -c 24576
You can hit enter at all of the prompts here. If it stalls at "Waiting for /dev/sdc12, hold the power button down on your phone about 10 seconds, or until your see "Qualcomm. Inc. Gobi Wireless Modem (QDL mode) disappear from your terminal window, then release it. 10 seconds or less after you do this, emmc_recovery will see your phone and proceed. Flashing Hboot will take several minutes, as it has to load data in ~23K chunks followed by a reset after each.
or you can open a new terminal window and run
Code:
$ sudo ./emmc_recover -r
10. Once that is finished. We have to reset the qcserial driver again.
Code:
$ sudo modprobe -r qcserial
11. And then recreate the block device
Code:
$ sudo mknod /dev/ttyUSB0 c 188 0
12. Now we restore the original mmcblk0p4 that you should have saved as "bakp4"
Code:
$ sudo ./emmc_recover -f ./bakp4 -d /dev/sdc4 -c 24576
13. Again, if it hangs, hold your phone's power button for about 10 seconds, then release. This file will flash very quickly (it's only 1K) and once it completes, you'll immediately notice that your charging light turns back on. You should see "Qualcomm, Inc." or "Qualcomm, Inc. Gobi Wireless modem (QDL mode) disappear from your terminal screen.
14. Press the thanks button for yarrimapirate. These are his tools. If you do not, I will find you and flash ICJ on your phone.
special thanks to
beaups (for helping me understand how to enumerate the partitions)
18th.abn (for getting me the 1.09 hboot and also agreeing to help me)
and yarrimapirate (not only for the scripts which he made for the Evo 4G LTE, but also agreeing to help me in this project and buying a one x with his own money)

Partition Table
Code:
[email protected]:/ $ su
[email protected]:/ # fdisk -l /dev/block/mmcblk0
Warning: deleting partitions after 60
Disk /dev/block/mmcblk0: 15.6 GB, 15634268160 bytes
1 heads, 16 sectors/track, 1908480 cylinders
Units = cylinders of 16 * 512 = 8192 bytes
Device Boot Start End Blocks Id System
/dev/block/mmcblk0p1 * 1 17 128 4d Unknown
Partition 1 does not end on cylinder boundary
/dev/block/mmcblk0p2 17 49 256 51 Unknown
Partition 2 does not end on cylinder boundary
/dev/block/mmcblk0p3 49 16382 130671 5d Unknown
Partition 3 does not end on cylinder boundary
/dev/block/mmcblk0p4 16382 1908480 15136784 5 Extended
Partition 4 does not end on cylinder boundary
/dev/block/mmcblk0p5 16383 16384 16 5a Unknown
/dev/block/mmcblk0p6 16385 16417 256 73 Unknown
/dev/block/mmcblk0p7 16417 18364 15577+ 5b Unknown
/dev/block/mmcblk0p8 18364 18396 256 5c Unknown
/dev/block/mmcblk0p9 18396 18524 1024 45 Unknown
/dev/block/mmcblk0p10 18524 18556 256 47 Unknown
/dev/block/mmcblk0p11 18556 18812 2048 46 Unknown
/dev/block/mmcblk0p12 18812 18940 1024 4c Unknown
/dev/block/mmcblk0p13 18940 18944 32 0 Empty
/dev/block/mmcblk0p14 18944 19712 6144 34 Unknown
/dev/block/mmcblk0p15 19712 19840 1024 36 Unknown
/dev/block/mmcblk0p16 19840 19968 1024 0 Empty
/dev/block/mmcblk0p17 19968 25728 46080 77 Unknown
/dev/block/mmcblk0p18 25729 27008 10240 7a Unknown
/dev/block/mmcblk0p19 27009 27649 5120 0 Empty
/dev/block/mmcblk0p20 27649 28672 8190+ 74 Unknown
/dev/block/mmcblk0p21 28673 30720 16384 48 Unknown
/dev/block/mmcblk0p22 30721 32768 16383+ 71 Unknown
/dev/block/mmcblk0p23 32769 32896 1022+ 76 Unknown
/dev/block/mmcblk0p24 32896 33408 4096 4a Unknown
/dev/block/mmcblk0p25 33409 33920 4096 4b Unknown
/dev/block/mmcblk0p26 33921 36481 20480 19 Unknown
/dev/block/mmcblk0p27 36481 36481 4 0 Empty
/dev/block/mmcblk0p28 36481 36513 256 23 Unknown
/dev/block/mmcblk0p29 36513 36515 16 0 Empty
/dev/block/mmcblk0p30 36515 36675 1280+ 0 Empty
/dev/block/mmcblk0p31 36675 36683 64 0 Empty
/dev/block/mmcblk0p32 36684 49152 99752 0 Empty
/dev/block/mmcblk0p33 49153 262144 1703935 83 Linux
/dev/block/mmcblk0p34 262145 294912 262143+ 83 Linux
/dev/block/mmcblk0p35 294913 606208 2490367+ 83 Linux
/dev/block/mmcblk0p36 606209 1908480 10418176 c Win95 FAT32 (LBA)
/dev/block/mmcblk0p37 16383 16384 16 5a Unknown
/dev/block/mmcblk0p38 16385 16417 256 73 Unknown
/dev/block/mmcblk0p39 16417 18364 15577+ 5b Unknown
/dev/block/mmcblk0p40 18364 18396 256 5c Unknown
/dev/block/mmcblk0p41 18396 18524 1024 45 Unknown
/dev/block/mmcblk0p42 18524 18556 256 47 Unknown
/dev/block/mmcblk0p43 18556 18812 2048 46 Unknown
/dev/block/mmcblk0p44 18812 18940 1024 4c Unknown
/dev/block/mmcblk0p45 18940 18944 32 0 Empty
/dev/block/mmcblk0p46 18944 19712 6144 34 Unknown
/dev/block/mmcblk0p47 19712 19840 1024 36 Unknown
/dev/block/mmcblk0p48 19840 19968 1024 0 Empty
/dev/block/mmcblk0p49 19968 25728 46080 77 Unknown
/dev/block/mmcblk0p50 25729 27008 10240 7a Unknown
/dev/block/mmcblk0p51 27009 27649 5120 0 Empty
/dev/block/mmcblk0p52 27649 28672 8190+ 74 Unknown
/dev/block/mmcblk0p53 28673 30720 16384 48 Unknown
/dev/block/mmcblk0p54 30721 32768 16383+ 71 Unknown
/dev/block/mmcblk0p55 32769 32896 1022+ 76 Unknown
/dev/block/mmcblk0p56 32896 33408 4096 4a Unknown
/dev/block/mmcblk0p57 33409 33920 4096 4b Unknown
/dev/block/mmcblk0p58 33921 36481 20480 19 Unknown
/dev/block/mmcblk0p59 36481 36481 4 0 Empty
/dev/block/mmcblk0p60 36481 36513 256 23 Unknown
Partition table entries are not in disk order
[email protected]:/ #

Awesome job! This will help out allot of people!
Sent from my Galaxy Nexus using xda app-developers app

absolutelygrim said:
(heres a good reason NOT to flash CWM, he was put into QHSUSB_DLOAD, which is, more or less, a bricked phone)
This is actually caused by flashing cwm thru Rom manager. Rom manager doesn't support evita, so the only choice is the endeavor HTC one x. Another international killer.....I still recommend twrp but just pointing this out.
Sent from my HTC One XL using Tapatalk 2
Click to expand...
Click to collapse

18th.abn said:
(heres a good reason NOT to flash CWM, he was put into QHSUSB_DLOAD, which is, more or less, a bricked phone)
This is actually caused by flashing cwm thru Rom manager. Rom manager doesn't support evita, so the only choice is the endeavor HTC one x. Another international killer.....I still recommend twrp but just pointing this out.
Sent from my HTC One XL using Tapatalk 2
Click to expand...
Click to collapse
I'll edit that in, thanks

Well somebody had to do it, glad it's you. Thanks for putting it altogether, hopefully we will advance towards a solution soon..:fingers-crossed:

here is my result from running sudo ./dg112.sh
HTC EVO 4G LTE HBOOT Downgrade Tool v0.2beta
FATAL: File killp4 missing.
I don't like the look of that FATAL, but what does it mean?

=JKT= said:
here is my result from running sudo ./dg112.sh
HTC EVO 4G LTE HBOOT Downgrade Tool v0.2beta
FATAL: File killp4 missing.
I don't like the look of that FATAL, but what does it mean?
Click to expand...
Click to collapse
Oh. killp4 is specific to downgrading the EVO.
your p4 is already dead, and i didn't include it in the folder
Code:
sudo ./dg112.sh -u
Stalled at restoring /dev/block/mmclk0p4 - partitions not being detected again..

Thank you for doing this, it will help so many people.

Mike724 said:
Thank you for doing this, it will help so many people.
Click to expand...
Click to collapse
Although tonight's experimentation did not necessarily succeed, it is very encouraging to see my phone respond in it's limited ways and see that there is still life inside of it, though it appear so dead on the outside. Take heart, all you other brick owners!

absolutelygrim said:
Oh. killp4 is specific to downgrading the EVO.
your p4 is already dead, and i didn't include it in the folder
Code:
sudo ./dg112.sh -u
Stalled at restoring /dev/block/mmclk0p4 - partitions not being detected again..
Click to expand...
Click to collapse
We actually kill P4 on the EVO by loading an evita P4 backup.
I bet the reverse is true for you guys, loading an EVO P4 backup would cause the desired panic.

18th.abn said:
This is actually caused by flashing cwm thru Rom manager. Rom manager doesn't support evita, so the only choice is the endeavor HTC one x. Another international killer.....I still recommend twrp but just pointing this out.
Click to expand...
Click to collapse
Right, I've seen numerous people do this. The head fake is that Google Play will let you install RomManager but there's nothing you can do with it on the One XL.
Sent from my Nexus 7 using Tapatalk 2

yarrimapirate said:
We actually kill P4 on the EVO by loading an evita P4 backup.
I bet the reverse is true for you guys, loading an EVO P4 backup would cause the desired panic.
Click to expand...
Click to collapse
Unfortunately our problem right now is being unable to write to the device.. The computer knows it's there, but we can't access it currently

absolutelygrim said:
Unfortunately our problem right now is being unable to write to the device.. The computer knows it's there, but we can't access it currently
Click to expand...
Click to collapse
Yes it seems like that.
about the new progress...How it appears and lsusb lists "Qualcomm Inc." ? The QHSUSB_DLOAD is appear immediately when the phone connect to the Win 7, right?
Or you mean that it appears in the Linux?

grim, yarimapirate, and I worked on my phone last night (my role was quite passive). Cheers to those guys for being extremely rad!
Looks like, at least in my case, I'll need to resort to more drastic solutions.
I'm in contact with a local guy who has a jtag rig. His last reply was exceedingly ambiguous:
for 2.20 bad news
- unfortunately, on 2.20 the hboot mmcblk0p12 is write protected
we working in jTag connection / controlled pins,
- drive test patterns on to the PCB
will be ready shortly
-----------------------------------------------------------------------------------------------
direct jTag connection to eMMc.
I asked him to clarify if this meant that he is looking into that solution, and it will be ready shortly, or if when I bring it in, he will use that solution and it will be ready soon after I give it to him.
regardless, I'll keep y'all posted on how this plays out.
edit: he replied and clarified that he is working on that solution.

lucentworld said:
Yes it seems like that.
about the new progress...How it appears and lsusb lists "Qualcomm Inc." ? The QHSUSB_DLOAD is appear immediately when the phone connect to the Win 7, right?
Or you mean that it appears in the Linux?
Click to expand...
Click to collapse
It appears in Linux for 2 seconds before going into download mode. This is good and bad.
Good because that possibly opens a 2 second window we can write to.
The bad news, the partitions aren't revealing so we can't write to them.
As of right now we have no idea how we can do this. If anyone has suggestions please post them here.
If jkt can get more info on that JTAG.. I'd love to jump into it and make my own to attempt more unbricks and see what else I can do. Im sure it'd get s-off, but the guys in the s-off thread want s non JTAG method.
Sent from my One X using xda app-developers app

absolutelygrim said:
It appears in Linux for 2 seconds before going into download mode. This is good and bad.
Good because that possibly opens a 2 second window we can write to.
The bad news, the partitions aren't revealing so we can't write to them.
As of right now we have no idea how we can do this. If anyone has suggestions please post them here.
If jkt can get more info on that JTAG.. I'd love to jump into it and make my own to attempt more unbricks and see what else I can do. Im sure it'd get s-off, but the guys in the s-off thread want s non JTAG method.
Sent from my One X using xda app-developers app
Click to expand...
Click to collapse
So if JKT's friend finally find that there are only JTAG can work... How can we open the at&t HOX ? It is integrative right? Maybe I will just post it to your place and after that send it back to me? I don't think I can do anytime with the hardware...like JTAG.
Hope for some soft unbricking ways.:good:

lucentworld said:
So if JKT's friend finally find that there are only JTAG can work... How can we open the at&t HOX ? It is integrative right? Maybe I will just post it to your place and after that send it back to me? I don't think I can do anytime with the hardware...like JTAG.
Hope for some soft unbricking ways.:good:
Click to expand...
Click to collapse
18th.abn has a video of taking it apart. I'll get it for you in a bit
Sent from my One X using xda app-developers app
yarrimapirate said:
Spent about an hour over Teamviewer with a bricked OneXL last night. It seems the phones flashed with international ROMs go through the standard SBL process, but for some reason don't expose their emmc partitions after a reset. Next step would be to disconnect/short the battery or let a bricked phone run completely flat, then try again.
Click to expand...
Click to collapse

absolutelygrim said:
It appears in Linux for 2 seconds before going into download mode. This is good and bad.
Good because that possibly opens a 2 second window we can write to.
The bad news, the partitions aren't revealing so we can't write to them.
As of right now we have no idea how we can do this. If anyone has suggestions please post them here.
If jkt can get more info on that JTAG.. I'd love to jump into it and make my own to attempt more unbricks and see what else I can do. Im sure it'd get s-off, but the guys in the s-off thread want s non JTAG method.
Sent from my One X using xda app-developers app
Click to expand...
Click to collapse
If we wrote a script that could first take the existing partitions that register, then when we plug the phone in, it immediately enumerates the partitions and tries to simultaneously write p4 to all of the new partitions repeatedly, could we sneak it in? I mean, the other partitions may as well be corrupt anyway. if we nail p4, can we get into fastboot? then we can write the others after
right now how we were doing it required id'ing the partitions manually, and thus missing the window.
also, this teardown video NOTE: REMOVED (wrong video, it was for int'l one x) didn't look that bad at all, actually. Mr jTag is willing, I'd let him rip apart my phone. Still unsure of his intentions/commitment.
heck, if it came down to it, i'd be willing to tear apart my own phone and see if i can find a cheap motherboard replacement. not sure what's all involved with getting it running with a fresh board.

absolutelygrim said:
18th.abn has a video of taking it apart. I'll get it for you in a bit
Sent from my One X using xda app-developers app
Click to expand...
Click to collapse
Oh thank you~
However I never heard that RIFF BOX has a support with the HOXL...
Even I don't know how to use that...
If it finally cannot be fixed expect using JTAG...
Do I need anything besides Riff Box? It seems that I cannot keep some tools like welding torch...when I live in a dorm.

CLOSE, please

All important information/ links will be moved to an INFO thread, since this is a question thread, we do not need it anymore.

Still looking.
Bump, can anyone help?
Saw this page:
forum.xda-developers .com/showthread.php?t=1959445
Was wondering if it's worth a shot.

Kernel released by Huawei.
For kernel/Rom Developers, Huawei has released the kernel for the Huawei Prism II online.
Attached is a notepad document with the links in them, since I am not allowed to post links. I apologize for the inconvenience.
ALSO
For anyone else with a Huawei device that has not released their kernel, I used the email format below:
Emal 1:
I would like the source code for my phone that is available to me. I am an android developer, and it would be useful to me if I have the
source code(that is offerred by Huawei).
The reply you will get:
Dear Customer,
Thank you for contacting Huawei device. The open source is under our technical department to make. Since the procedure is a little more complex, so please kindly be a little patient. We will keep you informed once available.Once again thank you for contacting Huawei device.
Best Regards.
Huawei Device Customer Care Team.
Give them 2-3 days, then E-mail once again! Be persistent!
2nd email:
Any new information about the source code?
The reply I got:
Dear Customer,
Thank you for contacting Huawei device. Please kindly check the source code link for your reference:
(link given above)
Once again thank you for contacting Huawei device.
Best Regards.
Huawei Device Customer Care Team.

Parted/FDisk Output on /dev/block/mmcblk0
streetdev22 said:
Bump, can anyone help?
Saw this page:
forum.xda-developers .com/showthread.php?t=1959445
Was wondering if it's worth a shot.
Click to expand...
Click to collapse
Tried the guide on my Prism II. Parted gave me an error. Possible reason for parted error is explained here: http://forum.xda-developers.com/showthread.php?t=2169709.
However, fdisk worked, but it doesn't clearly identify the partitons:
Edited to include gdisk output
parted:
Code:
parted /dev/block/mmcblk0
GNU Parted 1.8.8.1.179-aef3
Using /dev/block/mmcblk0
Welcome to GNU Parted! Type 'help' to view a list of commands.
(parted) print
print
print
Error: Unable to satisfy all constraints on the partition.
fdisk:
Code:
[email protected]:/ # fdisk -l /dev/block/mmcblk0
fdisk -l /dev/block/mmcblk0
Disk /dev/block/mmcblk0: 3909 MB, 3909091328 bytes
1 heads, 16 sectors/track, 477184 cylinders
Units = cylinders of 16 * 512 = 8192 bytes
Device Boot Start End Blocks Id System
/dev/block/mmcblk0p1 * 1 3 20 4d Unknown
Partition 1 does not end on cylinder boundary
/dev/block/mmcblk0p2 3 41 300 45 Unknown
Partition 2 does not end on cylinder boundary
/dev/block/mmcblk0p3 41 16681 133120 c Win95 FAT32 (LBA)
Partition 3 does not end on cylinder boundary
/dev/block/mmcblk0p4 16681 477184 3684031+ 5 Extended
Partition 4 does not end on cylinder boundary
/dev/block/mmcblk0p5 16897 18432 12288 6a Unknown
/dev/block/mmcblk0p6 18433 18944 4096 46 Unknown
/dev/block/mmcblk0p7 18945 19456 4096 63 GNU HURD or SysV
/dev/block/mmcblk0p8 19457 19840 3072 58 Unknown
/dev/block/mmcblk0p9 19969 20352 3072 4a Unknown
/dev/block/mmcblk0p10 20481 20864 3072 4b Unknown
/dev/block/mmcblk0p11 20993 21504 4096 47 Unknown
/dev/block/mmcblk0p12 21505 22528 8192 48 Unknown
/dev/block/mmcblk0p13 22529 25088 20480 60 Unknown
/dev/block/mmcblk0p14 25089 25600 4096 6c Unknown
/dev/block/mmcblk0p15 25601 50176 196608 83 Linux
/dev/block/mmcblk0p16 50177 60416 81920 83 Linux
/dev/block/mmcblk0p17 60417 191488 1048576 83 Linux
/dev/block/mmcblk0p18 191489 338944 1179648 83 Linux
/dev/block/mmcblk0p19 338945 477184 1105920 6b Unknown
gdisk:
Code:
[email protected]:/ # gdisk -l /dev/block/mmcblk0
gdisk -l /dev/block/mmcblk0
GPT fdisk (gdisk) version 0.8.4
Partition table scan:
MBR: MBR only
BSD: not present
APM: not present
GPT: not present
***************************************************************
Found invalid GPT and valid MBR; converting MBR to GPT format.
***************************************************************
Exact type match not found for type code 4D00; assigning type code for
'Linux filesystem'
Exact type match not found for type code 4500; assigning type code for
'Linux filesystem'
Exact type match not found for type code 6A00; assigning type code for
'Linux filesystem'
Exact type match not found for type code 4600; assigning type code for
'Linux filesystem'
Exact type match not found for type code 6300; assigning type code for
'Linux filesystem'
Exact type match not found for type code 5800; assigning type code for
'Linux filesystem'
Exact type match not found for type code 4A00; assigning type code for
'Linux filesystem'
Exact type match not found for type code 4B00; assigning type code for
'Linux filesystem'
Exact type match not found for type code 4700; assigning type code for
'Linux filesystem'
Exact type match not found for type code 4800; assigning type code for
'Linux filesystem'
Exact type match not found for type code 6000; assigning type code for
'Linux filesystem'
Exact type match not found for type code 6C00; assigning type code for
'Linux filesystem'
Exact type match not found for type code 6B00; assigning type code for
'Linux filesystem'
Warning! Main partition table overlaps the first partition by 33 blocks!
You will need to delete this partition or resize it in another utility.
Warning! Secondary partition table overlaps the last partition by
33 blocks!
You will need to delete this partition or resize it in another utility.
Disk /dev/block/mmcblk0: 7634944 sectors, 3.6 GiB
Logical sector size: 512 bytes
Disk identifier (GUID): E271C8D6-2001-435D-A466-BEFE7ED158CD
Partition table holds up to 128 entries
First usable sector is 34, last usable sector is 7634910
Partitions will be aligned on 1-sector boundaries
Total free space is 9599 sectors (4.7 MiB)
Number Start (sector) End (sector) Size Code Name
1 1 40 20.0 KiB 8300 Linux filesystem
2 41 640 300.0 KiB 8300 Linux filesystem
3 641 266880 130.0 MiB 0700 Microsoft basic data
5 270336 294911 12.0 MiB 8300 Linux filesystem
6 294912 303103 4.0 MiB 8300 Linux filesystem
7 303104 311295 4.0 MiB 8300 Linux filesystem
8 311296 317439 3.0 MiB 8300 Linux filesystem
9 319488 325631 3.0 MiB 8300 Linux filesystem
10 327680 333823 3.0 MiB 8300 Linux filesystem
11 335872 344063 4.0 MiB 8300 Linux filesystem
12 344064 360447 8.0 MiB 8300 Linux filesystem
13 360448 401407 20.0 MiB 8300 Linux filesystem
14 401408 409599 4.0 MiB 8300 Linux filesystem
15 409600 802815 192.0 MiB 8300 Linux filesystem
16 802816 966655 80.0 MiB 8300 Linux filesystem
17 966656 3063807 1024.0 MiB 8300 Linux filesystem
18 3063808 5423103 1.1 GiB 8300 Linux filesystem
19 5423104 7634943 1.1 GiB 8300 Linux filesystem
[email protected]:/ #

Partition Layout
streetdev22 said:
Recently rooted and unlocked the bootloader on my Huawei Prism II, but there is no custom recovery nor custom roms for this phone. I have tried determing the partition layout in order to dump the recovery, but I am unable to do so.
Tried earlier versions of romdump, but they returned with a segmentation failure.
Click to expand...
Click to collapse
I believe I've found the partition layout based on the /etc/recovery_mmc.fstab extracted from mmcblk0p13, but am not sure. The excerpt of my /etc/recovery_mmc.fstab file from mmcblk0p13 shows some partition names correlated to device names. Could someone verify this is a legitimate way to determine the partition layout? I've also attached the whole recovery_mmc.fstab file.
recovery_mmc.fstab excerpt:
Code:
/boot emmc /dev/block/mmcblk0p12
/cache ext4 /dev/block/mmcblk0p15
# /* < DTS2012062603367 lizhigang 20120626 begin */
/data ext4 /dev/block/mmcblk0p18 length=-16384
#/* < DTS2012062603367 lizhigang 20120626 end */
/recovery emmc /dev/block/mmcblk0p13
/misc emmc /dev/block/mmcblk0p7
/sdcard vfat /dev/block/mmcblk1p1 /dev/block/mmcblk1
/system ext4 /dev/block/mmcblk0p17
/sys_boot vfat /dev/block/mmcblk0p3
/fat vfat /dev/block/mmcblk0p3
/HWUserData vfat /dev/block/mmcblk0p19
#/*< DTS2012020804291 weizhonghui 20120208 begin */
/cust ext4 /dev/block/mmcblk0p16
#/* DTS2012020804291 weizhonghui 20120208 end >*/
#/* DTS2012011906026 chendeng 20120120 end > */
# /* DTS2012031506621 lishubin 20120321 end > */
Easier to read (joined fdisk and the recovery_mmc.fstab)
Code:
Device Boot Start End Blocks Id System
/dev/block/mmcblk0p1 * 1 3 20 4d Unknown /sdcard
/dev/block/mmcblk0p2 3 41 300 45 Unknown
/dev/block/mmcblk0p3 41 16681 133120 c Win95 FAT32 (LBA) /sys_boot and /fat
/dev/block/mmcblk0p4 16681 477184 3684031+ 5 Extended
/dev/block/mmcblk0p5 16897 18432 12288 6a Unknown
/dev/block/mmcblk0p6 18433 18944 4096 46 Unknown
/dev/block/mmcblk0p7 18945 19456 4096 63 GNU HURD or SysV /misc
/dev/block/mmcblk0p8 19457 19840 3072 58 Unknown
/dev/block/mmcblk0p9 19969 20352 3072 4a Unknown
/dev/block/mmcblk0p10 20481 20864 3072 4b Unknown
/dev/block/mmcblk0p11 20993 21504 4096 47 Unknown
/dev/block/mmcblk0p12 21505 22528 8192 48 Unknown /boot
/dev/block/mmcblk0p13 22529 25088 20480 60 Unknown /recovery
/dev/block/mmcblk0p14 25089 25600 4096 6c Unknown
/dev/block/mmcblk0p15 25601 50176 196608 83 Linux /cache
/dev/block/mmcblk0p16 50177 60416 81920 83 Linux /cust
/dev/block/mmcblk0p17 60417 191488 1048576 83 Linux /system
/dev/block/mmcblk0p18 191489 338944 1179648 83 Linux /data
/dev/block/mmcblk0p19 338945 477184 1105920 6b Unknown /HWUserData

Very nice!
Correlates with the hints found in other files as seen above, so I think we have successfully found the partition layout! I will take a look when my device gets here(originally was working on my relative's phone, but now I purchased it for myself). If this method is confirmed,we can to port CWM, thank you all!! After CWM, we should be able to make custom ROMs freely.

streetdev22 said:
Correlates with the hints found in other files as seen above, so I think we have successfully found the partition layout! I will take a look when my device gets here(originally was working on my relative's phone, but now I purchased it for myself). If this method is confirmed,we can to port CWM, thank you all!! After CWM, we should be able to make custom ROMs freely.
Click to expand...
Click to collapse
Great. I'm glad that someone can verify part of the partition layout. Hopefully, this means that the new information is credible too.

Prism 2 said:
Great. I'm glad that someone can verify part of the partition layout. Hopefully, this means that the new information is credible too.
Click to expand...
Click to collapse
How exactly did you extract the file? Did you extract it from mmcblk0p13? Have the device on hand, so I am trying to verify the findings.
Thanks.

Unpacking Recovery Image
streetdev22 said:
How exactly did you extract the file? Did you extract it from mmcblk0p13? Have the device on hand, so I am trying to verify the findings.
Thanks.
Click to expand...
Click to collapse
First, I made a selective backup using a google store app called Online Nandroid Backup https://play.google.com/store/apps/details?id=com.h3r3t1c.onnandbup&hl=en to make a backup on the "recovery" partition. Even though the app does not specify which block it copies, I believe the app makes a backup of /dev/block/mmcblk0p13 because it uses /system/partlayout4nandroid to determine the partition layout. If you look at the "cat /system/partlayout4nandroid" output below, you'll see that mmcblk0p13 corresponds to recovery.
Then I transferred the recovery.img from the sdcard to my computer.
From there, I followed the directions in Step 1 and Step 2 of http://www.imajeenyus.com/computer/20130301_android_tablet/android/unpack_repack_recovery_image.html to unpack and extract recovery.img.
Online Nandroid Backup Partition Layout:
Code:
[email protected]:/ # cat /system/partlayout4nandroid
cat /system/partlayout4nandroid
dev: size erasesize name
mmcblk0p1: 010000 000000 "modem"
mmcblk0p2: 000008 000000 "ssd"
mmcblk0p3: 000080 000000 "sbl1"
mmcblk0p4: 000100 000000 "sbl2"
mmcblk0p5: 000200 000000 "sbl3"
mmcblk0p6: 000200 000000 "aboot"
mmcblk0p7: 000200 000000 "rpm"
mmcblk0p8: 000200 000000 "tz"
mmcblk0p9: 002800 000000 "pad"
mmcblk0p10: 000c00 000000 "fsg"
mmcblk0p11: 002000 000000 "persist"
mmcblk0p12: 002800 000000 "boot"
[B]mmcblk0p13: 002800 000000 "recovery"[/B]
mmcblk0p14: 0b8000 000000 "system"
mmcblk0p15: 0d0000 000000 "cache"
mmcblk0p16: 000c00 000000 "modemst1"
mmcblk0p17: 000c00 000000 "modemst2"
mmcblk0p18: 040000 000000 "tombstones"
mmcblk0p19: 000400 000000 "misc"
mmcblk0p20: 001000 000000 "logo"
mmcblk0p21: 001000 000000 "logo2"
mmcblk0p22: 54c000 000000 "userdata"
mmcblk0p23: 00ffef 000000 "grow"
[email protected]:/ #

Probably correct.
My father(the owner of the phone) has once again left on a trip, so I will have to wait until Monday/Tuesday, when I receive my phone, to confirm these results.
My only issue with this is is why nandroid shows a different partition layout then what is shown in other files.
If partition 13 is recovery, there is no coincidence that you would find that fstab file in the extracted recovery.
Do you mind dumping all the extracted files from the recovery and uploading them to 4shared, mediafire, or any other cloud service as a compressed file(zip, tar)? I think the file is not coincidental, and that we have indeed found the partition layout(or at least the important partitions for our purposes).
Also, try dumping the boot partition that is currently identified (block 12) without using online nandroid backup(I think via dd should still work) and see if you can find similar files to that explained in the guide(.png, ramdisk directory, etc). If these files match up to what would be typically found in a boot.img or recovery.img, then the layout is most likely correct.
If these files match up to typical boot.img or recovery.img files, we can test the layout by changing something simple like a background before working on serious stuff.
Also, thanks for helping! Once we conclusively identify that this partition layout is correct, we can start to port clockworkmod.

streetdev22 said:
My father(the owner of the phone) has once again left on a trip, so I will have to wait until Monday/Tuesday, when I receive my phone, to confirm these results.
My only issue with this is is why nandroid shows a different partition layout then what is shown in other files.
If partition 13 is recovery, there is no coincidence that you would find that fstab file in the extracted recovery.
Do you mind dumping all the extracted files from the recovery and uploading them to 4shared, mediafire, or any other cloud service as a compressed file(zip, tar)? I think the file is not coincidental, and that we have indeed found the partition layout(or at least the important partitions for our purposes).
Also, try dumping the boot partition that is currently identified (block 12) without using online nandroid backup(I think via dd should still work) and see if you can find similar files to that explained in the guide(.png, ramdisk directory, etc). If these files match up to what would be typically found in a boot.img or recovery.img, then the layout is most likely correct.
If these files match up to typical boot.img or recovery.img files, we can test the layout by changing something simple like a background before working on serious stuff.
Also, thanks for helping! Once we conclusively identify that this partition layout is correct, we can start to port clockworkmod.
Click to expand...
Click to collapse
The extracted files in partition 13 can be found in post #44 of http://forum.xda-developers.com/showthread.php?t=2546455&page=5 labeled as "ramdisk.tar.bz2". I will make a dump of the boot partition using dd and run the tests tomorrow.

Looks validated, Also more tools
There are other guides on the matter of porting cyanogenmod..for example
http://wiki.cyanogenmod.org/w/Doc:_porting_intro
which even mentions a recovery.fstab file in recovery.img! So, that means the partition layout in the fstab file you found is most likely correct.
Another guide:
http://xda-university.com/as-a-developer/porting-clockworkmod-recovery-to-a-new-device
Also, there is an automated tool to porting cyanogenmod for new devices..
http://builder.clockworkmod.com/ (I would recommend avoiding the touch recovery for now, simple is all we need and we don't need more complications)
I am really feeling pretty confident about the partition layout found in the recovery.fstab, because one guide mentions it to be found in the recovery.img!
I would recommend making the changes to a recovery.img instead, because boot.img is still kinda scary (possible bricking )
Also, I think there is a command to try booting from a recovery.img without flashing the .img to the actual partition.
I think the command is mentioned here: http://forum.xda-developers.com/showthread.php?t=2233477
fastboot boot recovery.img is the command and it will not overwrite your existing recovery.
By using this command, you can try booting the stock recovery you extracted(to validate that we have a stock recovery available if we need it), and then boot the recovery.img you make with small edits, and then boot the recovery.img made from the automated CWM porter.
Thank you for replying so fast! We have made real progress in the last few days.
Edit:In the ramdisk that was extracted, another fstab exists on the root of the directory that is named fstab.msm7627, which is the same name from the file I located in post 1! They are the same file! I think this is validated.

Testing Recovery Partition
streetdev22 said:
I would recommend making the changes to a recovery.img instead, because boot.img is still kinda scary (possible bricking )
Also, I think there is a command to try booting from a recovery.img without flashing the .img to the actual partition.
I think the command is mentioned here: http://forum.xda-developers.com/showthread.php?t=2233477
fastboot boot recovery.img is the command and it will not overwrite your existing recovery.
By using this command, you can try booting the stock recovery you extracted(to validate that we have a stock recovery available if we need it), and then boot the recovery.img you make with small edits, and then boot the recovery.img made from the automated CWM porter.
Click to expand...
Click to collapse
I've made
a regular recovery.img using "dd if=/dev/block/mmcblk0p13 of=/sdcard/recovery.img" to make a copy of the recovery partition
a test recovery.img that is the same in every way to the original recovery.img except that all the images under /res/images is rotated 90 degrees. You can see the difference yourself by looking in res.rar attached below.
a clockworkmod recovery image from the clockworkmod recovery builder website
These images can be found attached below:
recovery.rar = original Huawei recovery image
recovery-test.rar = edited recovery image
recovery.img = clockworkmod recovery automatic builder image from http://jenkins.cyanogenmod.com/job/recovery/52069/
Unfortunately, I cannot test this image myself, because I do not want to unlock my bootloader yet.
If anyone with a rooted, unlocked Huawei Prism 2 is interested in helping to further the development of recovery roms for the Prism 2, I have made 3 tests to see if
the recovery partition is located in /dev/block/mmcblk0p13
the command "fastboot boot recovery.img", which we will be using extensively, can be used to boot the specified image file
the Clockworkmod Recovery image made from automated CWM porter successfully boots
The files you will need are provided below. I've also given instructions to the best of my ability without actually having done this.
To test if the recovery partition is located in /dev/block/mmcblk0p13:
Go into fastboot mode (step 2f in post #1 of http://forum.xda-developers.com/showthread.php?t=2546455)
Download the recovery.rar file below and extract it to get recovery.img.
Open up terminal
change directory to where you extracted recovery.img
type
Code:
fastboot boot recovery.img
See if phone boot into recovery
Next we test an edited recovery.img to see if "fastboot boot recovery.img" is truly letting us boot the image we've specified.
To find out, we're going to use the edited recovery.img and do pretty much the same thing except now with recovery-test.img:
Go into fastboot mode (step 2f in post #1 of http://forum.xda-developers.com/showthread.php?t=2546455)
Download the recovery-test.rar file below and extract it to get recovery-test.img.
Open up terminal
change directory to where you extracted recovery-test.img
type
Code:
fastboot boot recovery-test.img
See if any pictures are upside down (the battery symbol, numbers, or the android robot)
After completing the 2 tasks above, and verifying that we have a valid original recovery.img and that we can use
Code:
fastboot boot recovery.img
to boot a specific image file, we can start testing a very, very, very EXPERIMENTAL Clockworkmod Recovery image using fastboot. I would not rely on this image to make backups and I honestly do not know what kind of damage it might inflict on the phone so make a backup of everything before starting.
output from CWM automatic recovery builder: http://jenkins.cyanogenmod.com/job/recovery/52069/
To test if this CWM recovery image will boot and have the right partition layout:
Go into fastboot mode (step 2f in post #1 of http://forum.xda-developers.com/showthread.php?t=2546455)
Download the recovery.img.
Open up terminal
change directory to where you downloaded recovery.img
type
Code:
fastboot boot recovery.img
If the cwm recovery image boots, type
Code:
mount
See if /sdcard is mounted to the right partition)
If you're feeling lucky, make a backup to /sdcard **this step can cause damage to phone if /sdcard is mounted to the wrong partition**
Thanks for volunteering and bringing the Huawei Prism 2 one step closer to custom roms.

Will test as soon as I get the phone.
I should be getting my phone in the mail Tuesday-Wednesday, but I will test as soon as I get it in the mail and I get my bootloader unlocked. I shouldn't have an issue booting it, since it will boot without effecting my current recovery partition. Hopefully the cwm recovery boots as well.

streetdev22 said:
I should be getting my phone in the mail Tuesday-Wednesday, but I will test as soon as I get it in the mail and I get my bootloader unlocked. I shouldn't have an issue booting it, since it will boot without effecting my current recovery partition. Hopefully the cwm recovery boots as well.
Click to expand...
Click to collapse
Great! I really hope it works. Let me know if I can help with anything in the meantime.

Getting my phone today
My phone is coming today! I will let you know the results either later today or tomorrow. Also, could you pull a build.prop using ADB from your phone? This guy needs it: http://forum.xda-developers.com/showthread.php?p=49494728

niceeeee
Prism 2 said:
Great! I really hope it works. Let me know if I can help with anything in the meantime.
Click to expand...
Click to collapse
I tried them today and they work fine siiiiir. both booted while i was stuck in a boot loop from deleting my settins apk

Cjantolak said:
I tried them today and they work fine siiiiir. both booted while i was stuck in a boot loop from deleting my settins apk
Click to expand...
Click to collapse
Thats good news! Could you state specifically which 2 of the 3 images booted though? I'm assuming the original (recovery.rar file) and the edited (recovery-test.rar file) recovery.images, but want to make sure
In other words, did you test the clockworkmod recovery image?

first two
Prism 2 said:
Thats good news! Could you state specifically which 2 of the 3 images booted though? I'm assuming the original (recovery.rar file) and the edited (recovery-test.rar file) recovery.images, but want to make sure
In other words, did you test the clockworkmod recovery image?
Click to expand...
Click to collapse
I did just boot the clockworkmod recovery and i just booted up fine. os is running as it should other than the whole missing settings app. im stuck without root, without wifi, and usb debugging.
adb not installing the app either so idk.

Thanks for straightening out the confusion. Can you check the mounted partitions are correct? Afterwards you can use update.zip to install your settings.apk
---------- Post added at 01:11 AM ---------- Previous post was at 01:04 AM ----------
Never mind about checking the partition layout. I just remembered you don't have adb. I will try to make a better recovery image.

[Kindle Fire HD 7] 3rd Gen (2013) SOHO - Bring it back alive with emmc adapter flash

Hello,
I need some help. At the moment I am connected with the eMMC flash of my SOHO 3rd GEN tablet.
I used the exploitee.rs emmc adapter.
The problem:
-The tablet want not booting anymore. Stuck fw was on it (no idea wich fw).
-I try to bring it back with a fastboot cable but something burned on the mainboard (If you had a 3rd gen device and a microscope pls help)
What I want to try:
-I want to reflash the bootloader (are there two on this device???) and the recovery with my emmc adapter to be able to flash the stock fw again. I want to give him just manually 3.7V with a power adapter, at the battery connector.
The problem now:
I really dont know how to extract the right img-files from the stock-bin file. There are some different img files: (md5 sum at begining)
Code:
f82a8c5518a76b96b95dc0448b772d81 /media/galliumos/MULTIBOOT/Amazon_Kindle_Fire_HD_3rd_gen_SOHO/images/boot.img
Code:
a5224737ba83a65d40e3049ba6d71582 /media/galliumos/MULTIBOOT/Amazon_Kindle_Fire_HD_3rd_gen_SOHO/images/boot-prod.img
Code:
4e6181ea47c7868c2104147dc0b2fce6 /media/galliumos/MULTIBOOT/Amazon_Kindle_Fire_HD_3rd_gen_SOHO/images/u-boot.bin
Code:
38cfffa45008955f2887f7998dbd1c4e /media/galliumos/MULTIBOOT/Amazon_Kindle_Fire_HD_3rd_gen_SOHO/images/u-boot-prod.bin
Code:
aa4b135a185e5486656893f4c7101271 /media/galliumos/MULTIBOOT/Amazon_Kindle_Fire_HD_3rd_gen_SOHO/recovery_images/recovery-eng.img
Code:
5cba5636109eec7c7e5faa35104d65c0 /media/galliumos/MULTIBOOT/Amazon_Kindle_Fire_HD_3rd_gen_SOHO/recovery_images/recovery-prod.img
Code:
Here is recovery from the old system:
7e781998261c22852f6bae53e02335c6 /media/galliumos/MULTIBOOT/Amazon_Kindle_Fire_HD_3rd_gen_SOHO/recovery.img
I really think the bootloader was broken and that was the reason why the device was still black.
So I really would like to flash with
Code:
sudo dd if=/sdcard/bin-extract-stock/images/the-right.img of=/dev/sda2
the needed partitions. Like when I let the device making an update.
Can you help me to get the 100% right image files for the right partitions.
Here are some informations about the current partitions:
Code:
Disk /dev/sda: 14.6 GiB, 15634268160 bytes, 30535680 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: F9F21FFF-A8D4-5F0E-9746-594869AEC34E
Device Start End Sectors Size Type
/dev/sda1 256 511 256 128K Microsoft basic data
/dev/sda2 512 1023 512 256K Microsoft basic data
/dev/sda3 1024 1151 128 64K Microsoft basic data
/dev/sda4 1152 1183 32 16K Microsoft basic data
/dev/sda5 1184 1187 4 2K Microsoft basic data
/dev/sda6 2048 34815 32768 16M Microsoft basic data
/dev/sda7 34816 51199 16384 8M Microsoft basic data
/dev/sda8 51200 67583 16384 8M Microsoft basic data
/dev/sda9 67584 2623487 2555904 1.2G Microsoft basic data
/dev/sda10 2623488 4466687 1843200 900M Microsoft basic data
/dev/sda11 4466688 30535679 26068992 12.4G Microsoft basic data
Code:
Command (? for help): ?
b back up GPT data to a file
c change a partition's name
d delete a partition
i show detailed information on a partition
l list known partition types
n add a new partition
o create a new empty GUID partition table (GPT)
p print the partition table
q quit without saving changes
r recovery and transformation options (experts only)
s sort partitions
t change a partition's type code
v verify disk
w write table to disk and exit
x extra functionality (experts only)
? print this menu
Command (? for help): i
Partition number (1-11): 1
Partition GUID code: EBD0A0A2-B9E5-4433-87C0-68B6B72699C7 (Microsoft basic data)
Partition unique GUID: F9F21F00-A8D4-5F0E-9746-594869AEC34E
First sector: 256 (at 128.0 KiB)
Last sector: 511 (at 255.5 KiB)
Partition size: 256 sectors (128.0 KiB)
Attribute flags: 0000000000000000
Partition name: 'xloader'
Command (? for help): i
Partition number (1-11): 2
Partition GUID code: EBD0A0A2-B9E5-4433-87C0-68B6B72699C7 (Microsoft basic data)
Partition unique GUID: F9F21F01-A8D4-5F0E-9746-594869AEC34E
First sector: 512 (at 256.0 KiB)
Last sector: 1023 (at 511.5 KiB)
Partition size: 512 sectors (256.0 KiB)
Attribute flags: 0000000000000000
Partition name: 'bootloader'
Command (? for help): i
Partition number (1-11): 3
Partition GUID code: EBD0A0A2-B9E5-4433-87C0-68B6B72699C7 (Microsoft basic data)
Partition unique GUID: F9F21F02-A8D4-5F0E-9746-594869AEC34E
First sector: 1024 (at 512.0 KiB)
Last sector: 1151 (at 575.5 KiB)
Partition size: 128 sectors (64.0 KiB)
Attribute flags: 0000000000000000
Partition name: 'idme'
Command (? for help): i4
Partition number (1-11): 4
Partition GUID code: EBD0A0A2-B9E5-4433-87C0-68B6B72699C7 (Microsoft basic data)
Partition unique GUID: F9F21F03-A8D4-5F0E-9746-594869AEC34E
First sector: 1152 (at 576.0 KiB)
Last sector: 1183 (at 591.5 KiB)
Partition size: 32 sectors (16.0 KiB)
Attribute flags: 0000000000000000
Partition name: 'crypto'
Command (? for help): i
Partition number (1-11): 5
Partition GUID code: EBD0A0A2-B9E5-4433-87C0-68B6B72699C7 (Microsoft basic data)
Partition unique GUID: F9F21F04-A8D4-5F0E-9746-594869AEC34E
First sector: 1184 (at 592.0 KiB)
Last sector: 1187 (at 593.5 KiB)
Partition size: 4 sectors (2.0 KiB)
Attribute flags: 0000000000000000
Partition name: 'misc'
Command (? for help): i
Partition number (1-11): 6
Partition GUID code: EBD0A0A2-B9E5-4433-87C0-68B6B72699C7 (Microsoft basic data)
Partition unique GUID: F9F21F05-A8D4-5F0E-9746-594869AEC34E
First sector: 2048 (at 1024.0 KiB)
Last sector: 34815 (at 17.0 MiB)
Partition size: 32768 sectors (16.0 MiB)
Attribute flags: 0000000000000000
Partition name: 'efs'
Command (? for help): i
Partition number (1-11): 7
Partition GUID code: EBD0A0A2-B9E5-4433-87C0-68B6B72699C7 (Microsoft basic data)
Partition unique GUID: F9F21F06-A8D4-5F0E-9746-594869AEC34E
First sector: 34816 (at 17.0 MiB)
Last sector: 51199 (at 25.0 MiB)
Partition size: 16384 sectors (8.0 MiB)
Attribute flags: 0000000000000000
Partition name: 'recovery'
Command (? for help): i
Partition number (1-11): 8
Partition GUID code: EBD0A0A2-B9E5-4433-87C0-68B6B72699C7 (Microsoft basic data)
Partition unique GUID: F9F21F07-A8D4-5F0E-9746-594869AEC34E
First sector: 51200 (at 25.0 MiB)
Last sector: 67583 (at 33.0 MiB)
Partition size: 16384 sectors (8.0 MiB)
Attribute flags: 0000000000000000
Partition name: 'boot'
Command (? for help): i
Partition number (1-11): 9
Partition GUID code: EBD0A0A2-B9E5-4433-87C0-68B6B72699C7 (Microsoft basic data)
Partition unique GUID: F9F21F08-A8D4-5F0E-9746-594869AEC34E
First sector: 67584 (at 33.0 MiB)
Last sector: 2623487 (at 1.3 GiB)
Partition size: 2555904 sectors (1.2 GiB)
Attribute flags: 0000000000000000
Partition name: 'system'
Command (? for help): i
Partition number (1-11): 10
Partition GUID code: EBD0A0A2-B9E5-4433-87C0-68B6B72699C7 (Microsoft basic data)
Partition unique GUID: F9F21F09-A8D4-5F0E-9746-594869AEC34E
First sector: 2623488 (at 1.3 GiB)
Last sector: 4466687 (at 2.1 GiB)
Partition size: 1843200 sectors (900.0 MiB)
Attribute flags: 0000000000000000
Partition name: 'cache'
Command (? for help): i
Partition number (1-11): 11
Partition GUID code: EBD0A0A2-B9E5-4433-87C0-68B6B72699C7 (Microsoft basic data)
Partition unique GUID: F9F21F0A-A8D4-5F0E-9746-594869AEC34E
First sector: 4466688 (at 2.1 GiB)
Last sector: 30535679 (at 14.6 GiB)
Partition size: 26068992 sectors (12.4 GiB)
Attribute flags: 0000000000000000
Partition name: 'userdata'
gparted
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Greetings by I_did_it_just_tmrrow

overlode said:
Edit - SUCCESS!!! It seems I may have had one wire touching another so I tidied up the soldering and the eMMC was recognised straight away
I have successfully accessed the Soho eMMC and can see all partitions as in the attached image!!!
Now if only I could find the commands to backup the entire eMMC...
Click to expand...
Click to collapse
overlode said:
Ok, files uploaded -
Bootloader - https://drive.google.com/file/d/0BwMwdZJ36fBoVTNRVmNjX2FmZTQ/edit?usp=sharing
eMMC Dump - https://drive.google.com/file/d/0BwMwdZJ36fBoNTQyUENvbmVGY1E/edit?usp=sharing
Enjoy
Click to expand...
Click to collapse
I found this post here.
So now I had a 100% bootloader partition and my recovery partition.
What is about 'xloader' partition name?
And the partition 8: "boot". It that "u-boot.bin" from my source?
Pls, I need some answers.
Greetings by Idijt

its been awhile since i got mine revived! soo all this is like something new to me! howeveer ill provide what little that i have

abatoir said:
its been awhile since i got mine revived! soo all this is like something new to me! howeveer ill provide what little that i have
Click to expand...
Click to collapse
Did you still own your device? Can dump your partitions with dd?
Greetings by Idijt

No I don't own it anymore. But mine was an 8gb version, seems like yours is a 15gb version or something like that. I do have photos of my complete partitions.
Sent from my Redmi Note 2 using XDA Free mobile app
---------- Post added at 05:07 AM ---------- Previous post was at 04:48 AM ----------
this is my partiton table after succesfully uploading to emmc

Hello, I'm soho everything is normal, but then teardown accidentally short after the motherboard usb boot don't boot, but the computer have a reaction, but did not show for help how to solve the screen is black, from youdao translation

Hope this helps...
I did something similar. I was using a cheap cable so I swapped them out. I got a LG cable and plugged it in, well it borked my tablet. Black Screen, I took cable apart and found a resistor soldered to a pin! Tested it and it was sending odd pulses, whatever it broke mine. Here is a list of what I backed up before testing.
KF3_p1-xloader.img
-rwxrwxrwx 1 root vboxusers 35002 Sep 3 17:35 KF3_p1-xloader.rar
-rwxrwxrwx 1 root vboxusers 262144 Sep 3 17:27 KF3_p2-BootLoader-Orig.img
-rwxrwxrwx 1 root vboxusers 65536 Sep 3 17:35 KF3_p3-idme.img
-rwxrwxrwx 1 root vboxusers 16384 Sep 3 17:35 KF3_p4-crypto.img
-rwxrwxrwx 1 root vboxusers 2048 Sep 3 17:35 KF3_p5-misc.img
-rwxrwxrwx 1 root vboxusers 16777216 Sep 3 17:35 KF3_p6-efs.img
I assume you need to dd a original image to xloader &or bootloader.
I can only get mine in usb boot mode, which shows as omap4470 windows and Linux as:
Bus 002 Device 005: ID 0451:d012 Texas Instruments, Inc. I suspect I may need to mod & recompile the usbboot source. I think its hardcoded for 4430 or 4460.
*Your Method is even more promising.
I will upload the files if you need them. All except idme & efs as it contains my serials, etc. I *assume* those 2 files will work as they are stock and should have signatures intact.
Would You Post a Pic of the rs device connected to your Kindle?
I would love to find the serial and JTAG pinouts...?

any try this and did can repier of this problem

can you help me please
unimatrix725 said:
I did something similar. I was using a cheap cable so I swapped them out. I got a LG cable and plugged it in, well it borked my tablet. Black Screen, I took cable apart and found a resistor soldered to a pin! Tested it and it was sending odd pulses, whatever it broke mine. Here is a list of what I backed up before testing.
KF3_p1-xloader.img
-rwxrwxrwx 1 root vboxusers 35002 Sep 3 17:35 KF3_p1-xloader.rar
-rwxrwxrwx 1 root vboxusers 262144 Sep 3 17:27 KF3_p2-BootLoader-Orig.img
-rwxrwxrwx 1 root vboxusers 65536 Sep 3 17:35 KF3_p3-idme.img
-rwxrwxrwx 1 root vboxusers 16384 Sep 3 17:35 KF3_p4-crypto.img
-rwxrwxrwx 1 root vboxusers 2048 Sep 3 17:35 KF3_p5-misc.img
-rwxrwxrwx 1 root vboxusers 16777216 Sep 3 17:35 KF3_p6-efs.img
I assume you need to dd a original image to xloader &or bootloader.
I can only get mine in usb boot mode, which shows as omap4470 windows and Linux as:
Bus 002 Device 005: ID 0451:d012 Texas Instruments, Inc. I suspect I may need to mod & recompile the usbboot source. I think its hardcoded for 4430 or 4460.
*Your Method is even more promising.
I will upload the files if you need them. All except idme & efs as it contains my serials, etc. I *assume* those 2 files will work as they are stock and should have signatures intact.
Would You Post a Pic of the rs device connected to your Kindle?
I would love to find the serial and JTAG pinouts...?
View attachment 3866692
Click to expand...
Click to collapse
can you help me please

Nit an expert, mine is still bricked sitting on shelf.
arikurdi said:
can you help me please
Click to expand...
Click to collapse
I would suggest reading from first post. I don't know allot about the kindle. I spent many hours reading the threads to try and fix mine. I would suggest googling for an identification guide, since kindles are hard to tell apart. To make sure you are in the correct place. The second thing when needing help is to provide a detailed description of your problem. You increase chances of more than one person helping.

kindle fire soho
unimatrix725 said:
I would suggest reading from first post. I don't know allot about the kindle. I spent many hours reading the threads to try and fix mine. I would suggest googling for an identification guide, since kindles are hard to tell apart. To make sure you are in the correct place. The second thing when needing help is to provide a detailed description of your problem. You increase chances of more than one person helping.
Click to expand...
Click to collapse
my problem is my kindel fire soho is just read on pc omap4470 and idont know how to make short
and install driver on linux ihave linux but idont how is work iflashed wrong bootloader file

Hi, I also have Kindle Fire HD 7 Soho (2013). I was attempting to unlock the bootloader and install TWRP, following this thread:
https://forum.xda-developers.com/ki...ment/unlock-kfsowi-bootloader-unlock-t3262770
I was able to get into fastboot mode, then proceeded to flash boot with the hijack image, but in the next line, where the system partition is flashed with a system image, I mistakenly flashed system image to the boot partition. I then did continue, before I realized my mistake. It doesn't boot anymore, but I believe the card reader emmc access would be able to get me back in business again.
I've read this thread, and the thread for the HD 7 2012 Tate emmc, I don't see anything pointing to the connections for the card reader to the 2013 soho motherboard. If there is something that has been posted, could someone put a link in this thread? I think it will be very helpful for those of us that want to try that method to unbrick our Kindles (2013, 3rd generation). Thank you.
EDIT: After more reading, I came across a thread which shows the points to connect an sd card reader to the motherboard of a Kindle Fire HD 7 Soho (2013, 3rd gen) in order to access the emmc of the kindle, it will show up as a usb drive when the card reader is connected to the usb port.
https://forum.xda-developers.com/showthread.php?t=2674737&page=3
Here is another related link, it shows the connections using the pins of a micro-sdcard adapter, you should read the entire article because it mentions a 50k-ohm pull up resistor that is required between pins 2 & 4. This was used on a Kindle Fire HD 7 Tate (2012)
https://forum.xda-developers.com/kindle-fire-hd/7-inch-help/kindle-fire-hd-7-emmc-access-t2828906
I am waiting on a fastboot cable first, and it should arrive soon. If I can't get into fastboot mode with the new cable, then I will try the card reader method.

@crackitopen any news?
I found a pin decription for the SOHO and I got a image.
Currently I had still the broken SOHO-8GB from the first post. But I got a second SOHO-16GB version. I could imagine that the bootloader ist the same but I am not sure how to read it and flash it in the right way. Could anybody help with that?
Greetings by Idijt

I_did_it_just_tmrrow said:
@crackitopen any news?
Click to expand...
Click to collapse
Hi Sorry for the late reply, but yes - I waited for the fastboot cable to arrive, and when it did, I was able to get into fastboot mode, so I had only to reflash those 2 partitions. I was very careful this time around, and I was successful in updating the Soho to CyanogenMod 12 unofficial Soho, Android 5.0.2 as described in that other post that I referenced.

crackitopen said:
Hi Sorry for the late reply, but yes - I waited for the fastboot cable to arrive, and when it did, I was able to get into fastboot mode, so I had only to reflash those 2 partitions. I was very careful this time around, and I was successful in updating the Soho to CyanogenMod 12 unofficial Soho, Android 5.0.2 as described in that other post that I referenced.
Click to expand...
Click to collapse
Did you have some tipps for me?
I own 2 SOHO devices and grab from the first one the following partitions:
Code:
=========================================
soho:/ # df
Filesystem 1K-blocks Used Available Use% Mounted on
tmpfs 470440 480 469960 1% /dev
tmpfs 470440 0 470440 0% /mnt
/dev/block/mmcblk0p10 1251544 707172 544372 57% /system
/dev/block/mmcblk0p12 5316696 2888156 2428540 55% /data
/dev/block/mmcblk0p11 907096 15708 891388 2% /cache
/dev/fuse 5316696 2888156 2428540 55% /mnt/runtime/default/emulated
/dev/fuse 5316696 2888156 2428540 55% /mnt/runtime/read/emulated
/dev/fuse 5316696 2888156 2428540 55% /mnt/runtime/write/emulated
=========================================
soho:/ # ls -la /dev/block/platform/omap_hsmmc.1/by-name
total 0
drwxr-xr-x 2 root root 280 2017-10-22 01:35 .
drwxr-xr-x 4 root root 380 2017-10-22 01:35 ..
lrwxrwxrwx 1 root root 20 2017-10-22 01:35 boot -> /dev/block/mmcblk0p8
lrwxrwxrwx 1 root root 20 2017-10-22 01:35 bootloader -> /dev/block/mmcblk0p2
lrwxrwxrwx 1 root root 21 2017-10-22 01:35 cache -> /dev/block/mmcblk0p11
lrwxrwxrwx 1 root root 20 2017-10-22 01:35 crypto -> /dev/block/mmcblk0p4
lrwxrwxrwx 1 root root 20 2017-10-22 01:35 efs -> /dev/block/mmcblk0p6
lrwxrwxrwx 1 root root 20 2017-10-22 01:35 exploit -> /dev/block/mmcblk0p9
lrwxrwxrwx 1 root root 20 2017-10-22 01:35 idme -> /dev/block/mmcblk0p3
lrwxrwxrwx 1 root root 20 2017-10-22 01:35 misc -> /dev/block/mmcblk0p5
lrwxrwxrwx 1 root root 20 2017-10-22 01:35 recovery -> /dev/block/mmcblk0p7
lrwxrwxrwx 1 root root 21 2017-10-22 01:35 system -> /dev/block/mmcblk0p10
lrwxrwxrwx 1 root root 20 2017-10-22 01:35 xloader -> /dev/block/mmcblk0p1
The following partition was to big ofr internal memory:
Code:
lrwxrwxrwx 1 root root 21 2017-10-22 01:35 userdata -> /dev/block/mmcblk0p12
What would I like to do next:
I wanna solder my gtv-Hacker emmc adapter to my SOHO mainboard to fix it. Then I would like to flash "bootloader -> /dev/block/mmcblk0p2" & "recovery -> /dev/block/mmcblk0p7" & "exploit -> /dev/block/mmcblk0p9".
Commands to flash the 3 partitions?
Greetings by Idijt

Jesus christ you fixed it? You are a god to me OP.

Galaxyninja66 said:
Jesus christ you fixed it? You are a god to me OP.
Click to expand...
Click to collapse
If you mean me, no I dont fix it yet. I was on the right way but then my noob-Linux knowledge or any other reason seems to destroy the one mainboard. I had SOHO mainboard, one with hardware error and one with software-Brick error.
But I think you have another kindle, I had 2 SOHO boards and you seems to have a TATE:
Code:
>KFHD 7 2012 (tate) - CyanogenMod 13 (Considering an SFOS port)
Greetings by Idijt

I_did_it_just_tmrrow said:
If you mean me, no I dont fix it yet. I was on the right way but then my noob-Linux knowledge or any other reason seems to destroy the one mainboard. I had SOHO mainboard, one with hardware error and one with software-Brick error.
But I think you have another kindle, I had 2 SOHO boards and you seems to have a TATE:
Code:
>KFHD 7 2012 (tate) - CyanogenMod 13 (Considering an SFOS port)
Greetings by Idijt
Click to expand...
Click to collapse
I know we have different kindles, but raising a messed up board from the dead is an accomplishment no less
On a side note, and SFOS port might not be possible due to the nature of the Kindle fire bootloader. Each build just goes straight to fastboot which is un heard of on any other device.

Just wanted to say thank you to @overlode and @unimatrix725. Thanks to you I was able to bring my hard bricked Fire HD 3rd gen (soho) back to the land of living. I've made a mistake of flashing a wrong bootloader.
After a bit of googling I came across a thread on xda where @overlode shared an immensely helpful photo with eMMC pins mapped out - you rock! Using this mapping I was able to solder an usb sdcard reader to the eMMC and access it from gparted. Then I've found this thread where @unimatrix725 shared his original bootloader.img which I then subsequently flashed to my device. Now my Fire HD is happy again - thank you!

Glad you were able to sort it @pfoltyn, I haven't looked at this for a couple of years and have since moved on to other projects but glad it's still helping people

ZP980 unbrick/study of partition table

Hi to all, I hope to be posting in the right section...otherwise...punish me plz
It's a long story, so i hope that someone has time and want to put some effort to help me understand what i'm doing wrong.
By the way i work in IT field and have some knowledge about linux (let's say 5 on 10) but not so many on how android really works, but i'm confortable with custom recovery and roms, i'm still using an s4 mini (GT-I9195) with mine android 9 custom rom and i'm super happy with it.
Now that presentation are done , here is the matter.
I've found an old zp980 32GB (NOT the "plus one") that some years ago i've rooted it flashed with recovery and custom rom. all was working, but at some point i started playing with fdisk and parted and i messed up things.
Honestly i don't remember what exactly i was doing, but now the status of the phone is:
System not booting
I can enter into Recovery (custom TWRP by dezmen3 v2.4.4.0)
I can connect to adb into recovery
I cannot flash rom trough recovery due the actual system partition (589 MB)
I cannot flash the original rom trough SP flash tool due "SFT enable dram failed (4032)" error
The partitions actually are (what i can see from recovery):
System (589 MB)
Data (54MB)
Boot (6 MB)
Recovery (6MB)
Cache (4 MB)
uboot(0 MB)
nvram (5 MB)
Free space: 27412 MB
Actually, I've tried to reformat the memory using SP flah tool, but i got the same error "SFT enable dram failed (4032)", all drivers are ok, i can see COM port in deivce manager tried win 10 and even win 7.
SP tool ver. used v5 1720 more updated version tells me that the brick i'm tringo to flash in not supported anymore xD
Here a dump of fdisk -ul /dev/block/mmcblk0 from adb shell
Bash:
Device Boot Start End Blocks Id System
/dev/block/mmcblk0p1 1024 1022 2147483647+ 5 Extended
Partition 1 does not end on cylinder boundary
/dev/block/mmcblk0p2 26624 47103 10240 83 Linux
Partition 2 does not end on cylinder boundary
/dev/block/mmcblk0p3 47104 67583 10240 83 Linux
Partition 3 does not end on cylinder boundary
/dev/block/mmcblk0p4 93184 105471 6144 83 Linux
Partition 4 does not end on cylinder boundary
/dev/block/mmcblk0p5 134144 1465343 665600 83 Linux
/dev/block/mmcblk0p6 4869120 1022 2145049599+ 83 Linux
if i make a print from parted (pushed with adb) I get:
Error: Can't have a partition outside the disk!
Before i was also having an error saying that there was an extended partition into a logical one (don't ask me how I do it), but i removed it
So, now....what to to to rescue this device?
by the way honestly except for the instinct of "recover things that doesn't work" my main purpose is understand:
What I've messed on the partitions
Why sp flash tool can't reformat/flash the memory (i haven't tried to manually modify it again)

no brave person hat want to help me to brick it in a bad way?
EDIT NEW INFO
i've understtod that the problem was caused by
/dev/block/mmcblk0p1
and
/dev/block/mmcblk0p6
start and end were inverted , them were overflowing.
Now i used fdisk to remove part 1 (the extended), so i've lost also 5 and 6 (system and cache) and i have recreated them using 1 GB for each and using correct sector order.
now SD and try to flash a ....random compatible rom....see u later for info.
Cross your finger for me xD

flash failed it cant mount system and emmc.....
and now
~ # cat /etc/fstab
/cache ext4 rw
/data ext4 rw
/emmc vfat rw
/system ext4 rw
/sdcard vfat rw
/sd-ext auto rw

if someone has a zp980/c2 working can please post me the result of
cat /etc/fstab
from adb shell??
and a fdisk -ul?

Need a repartitioning expert to restore an omitted partition

I think I did some mistakes while trying to reflash a rom on my Sony Xperia S (lt26i).
I was following this guide, the first time it worked but then I decided to ungoogle my phone but it went bad.
[GUIDE/TUTORIAL/HOWTO] Sony Xperia S stock to Android 8.1 Oreo
[GUIDE/TUTORIAL/HOWTO] Sony Xperia S stock to Android 8.1 Oreo [GUIDE/TUTORIAL/HOWTO] Upgrade Sony Xperia S (Model LT26i codename nozomi) from Android 2.3.7 to Android 8.1 Oreo / nAOSP Rom This detailed step-by-step guide helps you transform...
forum.xda-developers.com
My problem is that I deleted my OS and TWRP can't read the data partition nor mount to Windows.
So now, with djibe89's help (the OP of the guide), I managed to figure out that my data partition is corrupted.
Using the adb shell, like on step 12 of the guide, I went to the partitions and it gave me this
Omitting empty partition (14)
Disk /dev/block/mmcblk0: 31.9 GB, 31910264832 bytes
4 heads, 16 sectors/track, 973824 cylinders
Units = cylinders of 64 * 512 = 32768 bytes
Device Boot Start End Blocks Id System
/dev/block/mmcblk0p1 1 65 2048 f0 Linux/PA-RISC boot
Partition 1 does not end on cylinder boundary
/dev/block/mmcblk0p2 * 65 81 512 4d Unknown
Partition 2 does not end on cylinder boundary
/dev/block/mmcblk0p3 129 768 20480 48 Unknown
Partition 3 does not end on cylinder boundary
/dev/block/mmcblk0p4 769 954240 30511104 5 Extended
Partition 4 does not end on cylinder boundary
/dev/block/mmcblk0p5 785 800 512 46 Unknown
/dev/block/mmcblk0p6 833 928 3072 4a Unknown
/dev/block/mmcblk0p7 961 1056 3072 4b Unknown
/dev/block/mmcblk0p8 1089 1184 3072 58 Unknown
/dev/block/mmcblk0p9 1217 1376 5120 70 Unknown
/dev/block/mmcblk0p10 1409 1664 8192 83 Linux
/dev/block/mmcblk0p11 1665 2176 16384 f0 Linux/PA-RISC boot
/dev/block/mmcblk0p12 2177 34944 1048576 83 Linux
/dev/block/mmcblk0p13 34945 42944 256000 83 Linux
~ # fdisk -l /dev/block/mmcblk0
Click to expand...
Click to collapse
The partition 14 should be the data one, that i already merged with the 15 the first time i flashed the rom.
What should I do?

try deleting it and let Android generate new one??

Code:
fastboot erase userdata
fastboot format:ext4 userdata
fastboot reboot
now there's a high chance that your device doesn't support " fastboot format:ext4 userdata "
here's an alternative
fastboot erase userdata <~ never reboot your device after typing this command you would go on infinite bootloop type the next command ...
fastboot reboot recovery <~ if this command does not work and just restarted your device instead of going recovery mode you are now on bootloop ... access recovery mode by pressing combination key instead
via recovery mode do "wipe data / factory reset"
then reboot

ineedroot69 said:
Code:
fastboot erase userdata
fastboot format:ext4 userdata
fastboot reboot
now there's a high chance that your device doesn't support " fastboot format:ext4 userdata "
here's an alternative
fastboot erase userdata <~ never reboot your device after typing this command you would go on infinite bootloop type the next command ...
fastboot reboot recovery <~ if this command does not work and just restarted your device instead of going recovery mode you are now on bootloop ... access recovery mode by pressing combination key instead
via recovery mode do "wipe data / factory reset"
then reboot
Click to expand...
Click to collapse
the first method didn't work because of the format command like you predicted.
then i did the <erase userdata> but i think the <reboot recovery> command isn't available because it returns me the commands list. so i used this command from the list
fastboot reboot-bootloader
Click to expand...
Click to collapse
then unplugged the usb and rebooted on twrp.
now my data partition went back to 0mb (going to wipe -> advanced wipe -> data -> repair or change file system) and i can't even reformat it.
should i re-do the adb procedure to recreate the data partition?

mongolino0 said:
the first method didn't work because of the format command like you predicted.
then i did the <erase userdata> but i think the <reboot recovery> command isn't available because it returns me the commands list. so i used this command from the list
then unplugged the usb and rebooted on twrp.
now my data partition went back to 0mb (going to wipe -> advanced wipe -> data -> repair or change file system) and i can't even reformat it.
should i re-do the adb procedure to recreate the data partition?
Click to expand...
Click to collapse
yes your device won't boot without userdata partition since it got deleted with "fastboot erase userdata" so you need to recreate it by "formatting" it somehow

so i wanted to "recreate" the data partition with adb but now i can't even use adb.
i went to mount on twrp with the phone connected and the cmd still running from 2 hours ago. when I type adb devices I can't find
... is it possible that i did some irreversible mistake?

mongolino0 said:
so i wanted to "recreate" the data partition with adb but now i can't even use adb.
i went to mount on twrp with the phone connected and the cmd still running from 2 hours ago. when I type adb devices I can't find
... is it possible that i did some irreversible mistake?
Click to expand...
Click to collapse
you have TWRP flashed? you can't use it to format data?
also looking at the Sony Xperia S (lt26i) specification it was released back in February 2012 i guess it has serve its purpose for too long it is time for it to retire