I've looked around quite a bit, but can't find anyone who has had this problem when restoring. I was trying out Paranoid Android 3.10 D2VZW on my Galaxy SIII, and decided to go back to JellyBam 8.2.0 D2VZW. Both are 4.2.2 ROMs. I rebooted into CWM Recovery, wiped data and cache (can't remember if I wiped the Dalvik), and restored my JellyBam backup. The restore went fine, and I rebooted the system from CWM...nothing! Phone is completely black, no boot up at all. I tried the power button, a battery pull, booting into recovery, and booting into download. When I plug my phone into my computer (a Mac with Windows running in Parallels), I get QHSUSB_DLOAD. So far my research tells me this means my phone is hard-bricked. If I plug in without a battery, I get a red LED light that extinguishes after a few minutes. My understanding of hard-bricking is that it's caused by flashing ROMs not intended for my phone (i.e. an international version ROM). Why would my phone hard-brick if the last thing I did is restore a backup from a previously-working ROM built for my phone? I didn't check the md5, but if the md5 failed wouldn't the restore fail too? I literally can't do anything with my phone. No display, no Odin/download, no recovery. The only indications that it isn't completely fried are the red LED and my computer recognizing the QHSUSB_DLOAD and making a notification sound when it's connected or disconnected. I have no problem sending it to be JTAGed if need be, but I'm not 100% that it's hard-bricked. Any suggestions?
ransdell2 said:
I've looked around quite a bit, but can't find anyone who has had this problem when restoring. I was trying out Paranoid Android 3.10 D2VZW on my Galaxy SIII, and decided to go back to JellyBam 8.2.0 D2VZW. Both are 4.2.2 ROMs. I rebooted into CWM Recovery, wiped data and cache (can't remember if I wiped the Dalvik), and restored my JellyBam backup. The restore went fine, and I rebooted the system from CWM...nothing! Phone is completely black, no boot up at all. I tried the power button, a battery pull, booting into recovery, and booting into download. When I plug my phone into my computer (a Mac with Windows running in Parallels), I get QHSUSB_DLOAD. So far my research tells me this means my phone is hard-bricked. If I plug in without a battery, I get a red LED light that extinguishes after a few minutes. My understanding of hard-bricking is that it's caused by flashing ROMs not intended for my phone (i.e. an international version ROM). Why would my phone hard-brick if the last thing I did is restore a backup from a previously-working ROM built for my phone? I didn't check the md5, but if the md5 failed wouldn't the restore fail too? I literally can't do anything with my phone. No display, no Odin/download, no recovery. The only indications that it isn't completely fried are the red LED and my computer recognizing the QHSUSB_DLOAD and making a notification sound when it's connected or disconnected. I have no problem sending it to be JTAGed if need be, but I'm not 100% that it's hard-bricked. Any suggestions?
Click to expand...
Click to collapse
It's definitely hard bricked, whatever happened is very strange though, as a nandroid doesn't usually mess up your boot partition.
Flashing a rom not intended for your phone can cause a hard brick, but that's not the only way it can happen. Somewhere in the restore process your boot partition got corrupted. Your base coding somehow is not being recognized, and your computer and phone can't tell what's supposed to run. A jtag is really your only option.
TWRP offers you the option to disable the boot and recovery partition when restoring. After you fix your phone, I'd recommend trying that out so you're absolutely sure your boot partition doesn't get touched. Those really don't need to be restored anyway.
Sorry that happened to you.
Sent from my SCH-I535 using Tapatalk 2
Bummer. Thanks for the input. I kinda figured that was the case, but was hoping I was missing something. Guess I'm going to have it JTAGed, probably by Mobile Tech Videos. The process looks fairly simple. If the equipment costs were comparable to having someone else do it I might do it myself, but if that were the case everyone else would be doing that too! I'll let you know how it goes.
ransdell2 said:
Bummer. Thanks for the input. I kinda figured that was the case, but was hoping I was missing something. Guess I'm going to have it JTAGed, probably by Mobile Tech Videos. The process looks fairly simple. If the equipment costs were comparable to having someone else do it I might do it myself, but if that were the case everyone else would be doing that too! I'll let you know how it goes.
Click to expand...
Click to collapse
I think the price is reasonable if you factor in equipment and labor.
Sent from my SCH-I535 using Tapatalk 2
BadUsername said:
I think the price is reasonable if you factor in equipment and labor.
Sent from my SCH-I535 using Tapatalk 2
Click to expand...
Click to collapse
Got my phone JTAGed by Patrick Walls (whose service is available on eBay for ~$35), and it works great. Fast service and great communication from Patrick. The phone came back unrooted with a stock 4.1.2 ROM. Of course I immediately re-rooted it and flashed a fresh JellyBAM ROM to it (with a huge feeling of trepidation), and so far everything is working, with the exception of the camera (I get "Can't connect to camera" after taking one picture, and a reboot is the only thing that enables the camera again, for one pictures, then can't connect, reboot, one pic, can't connect, etc.).
Having never hard-bricked before after many, many ROM changes on a Fascinate and about 10 ROM changes on my S3, I'm a little nervous about changing them now. Is my hesitation unfounded providing I don't mess with the bootchain? To root my phone I flashed the VRALEC bootchain, then TWRP, then rooted, then JellyBAM, then the VRBMD3 bootchain, as per this rooting guide:
http://forum.xda-developers.com/showthread.php?t=2046439
Now that I've put my phone back to the Jelly Bean bootchain, I should be free to flash ROMs built for my device without a serious concern about hard-bricking, right?
ransdell2 said:
Got my phone JTAGed by Patrick Walls (whose service is available on eBay for ~$35), and it works great. Fast service and great communication from Patrick. The phone came back unrooted with a stock 4.1.2 ROM. Of course I immediately re-rooted it and flashed a fresh JellyBAM ROM to it (with a huge feeling of trepidation), and so far everything is working, with the exception of the camera (I get "Can't connect to camera" after taking one picture, and a reboot is the only thing that enables the camera again, for one pictures, then can't connect, reboot, one pic, can't connect, etc.).
Having never hard-bricked before after many, many ROM changes on a Fascinate and about 10 ROM changes on my S3, I'm a little nervous about changing them now. Is my hesitation unfounded providing I don't mess with the bootchain? To root my phone I flashed the VRALEC bootchain, then TWRP, then rooted, then JellyBAM, then the VRBMD3 bootchain, as per this rooting guide:
http://forum.xda-developers.com/showthread.php?t=2046439
Now that I've put my phone back to the Jelly Bean bootchain, I should be free to flash ROMs built for my device without a serious concern about hard-bricking, right?
Click to expand...
Click to collapse
Glad you got it working.
There's always a risk of something going wrong and a hard brick reoccurring, you just had bad luck. I don't think your brick had anything to do with your bootchain.
I think what probably happened was when you made a nandroid in cwm, the boot partition somehow got corrupted. CWM by default restores your boot, recovery, data, system, and cache partitions. In the advanced restore section, you can restore one at a time but you have no way of simply disabling a particular partition from being restored. I think since the boot partition was messed up, it erased your good data and hard-bricked your phone.
TWRP by default only backs up your data, cache, and system partitions and leaves your boot and recovery partitions alone. If you restore that backup, then there's pretty much no way a hard brick can happen. I can't think of any reason why you really need to backup your recovery or boot partition.
Sent from my SCH-I535 using Tapatalk 2
BadUsername said:
Glad you got it working.
There's always a risk of something going wrong and a hard brick reoccurring, you just had bad luck. I don't think your brick had anything to do with your bootchain.
I think what probably happened was when you made a nandroid in cwm, the boot partition somehow got corrupted. CWM by default restores your boot, recovery, data, system, and cache partitions. In the advanced restore section, you can restore one at a time but you have no way of simply disabling a particular partition from being restored. I think since the boot partition was messed up, it erased your good data and hard-bricked your phone.
TWRP by default only backs up your data, cache, and system partitions and leaves your boot and recovery partitions alone. If you restore that backup, then there's pretty much no way a hard brick can happen. I can't think of any reason why you really need to backup your recovery or boot partition.
Sent from my SCH-I535 using Tapatalk 2
Click to expand...
Click to collapse
Great, thanks for the info! I'll make sure that the boot and recovery partitions aren't touched in the future. I've primarily used CWM, but am probably just going to stick with TWRP.
Related
so, last night my phone was acting wierd... slow, battery was getting destroyed literally in an hour or two so i cleaned it up..
somehow i lost clockwork recovery... no flippin idea what happened, i never flashed or installed anything, but i went to do a backup and all i got was samsung recovery.
i did not lose root...
tried to install via rom manager and it said it worked... yeah whatever, that program is rubbish and ALWAYS says it worked...
anyways rebooted to a black screen but the capacitive buttons would light up if i touched them.
finally it installed but nothing worked and the phone locked up.
by the way rom manager installed CWM 3.0.0.8 (orange)
so now i had to completely blow out the phone, reroot, reinstall CWM (which worked the first time) but nothing is working in clockwork again.
back up.. nope says error backing up.. thats it
restore... nope, something about only having 8gb of space on my SDcard
i can wipe cache,, or so it seems.
but
if i wipe dalvik it locks the phone and i completely lose CWM again.
its acting like CWM is only temporary or something.
so what the heck.. i have never seen this before... ever.
I cant do anything with regards to bqcking up or restoring.
I cant.flash anything either even though rom manager boots to a portion of cwm which tries to flash a eom. But the phone just reboots.
Sent from my SCH-I500 using Tapatalk
Can't lie - Karma's a *****
Try going back to stock and starting over.
foxfire450 said:
Try going back to stock and starting over.
Click to expand...
Click to collapse
please be sure you read my post in its entirety and not bits and pieces.
i did finally get the latest CM7 installed and its running ok.
havent tried to do other things in CWM yet
akellar said:
Can't lie - Karma's a *****
Click to expand...
Click to collapse
you aint kidding...
but
its a phone, my life doesnt end if my phone goes to hell
just wierd, i have never lost clockwork before.
v_lestat said:
please be sure you read my post in its entirety and not bits and pieces.
Click to expand...
Click to collapse
In fairness, it's not immediately clear what you did after getting CWM Orange 3 installed---and really, ROM Manager should only ever be used on our phones if you're using the latest (CWM 4) on an MTD ROM.
That said: IF you think you need to do this (it sounds like if you got CM7 installed, you don't, but offering the advice all the same): take foxfire450's advice. Then do the entire process all over again. I've heard of people having issues with a lagfux or MTD removal unless they did the process twice. You might even consider the RFS Formatter if you're still having trouble.
Again though, that's all largely academic if you're running fine now. *shrug* Up to you to try if you think it's worth bothering at this point.
Had just flashed the latest CM9 nightly (clean install, fresh wipe) yesterday and everything was running fine.
This morning, woke up, my phone was turned off. When powering it on it hung on the google screen. Fastboot still working, booted into recovery only to find that I would get error messages when trying to load my backs "E:unable to mount /sdcard". Apparently it also couldn't mount /data. So I was unable to flash any images or restore or boot up.
Seeing that fastboot was still working I assume I'm not bricked yet. I tried flashing a new boot and cwm recovery via fastboot - no dice. Same errors.
I don't have a recent backup of anything in sdcard, but at this point I'm willing to sacrifice it.
Found this thread http://forum.xda-developers.com/showthread.php?t=1078213
and I'm trying to follow the steps to flash back to stock GB. using the GRJ22 images
It flashed the boot and recovery without issue but seems to hang while flashing the system.img. I know it's a big file, but it was up to ~2hrs with it still transferring. I pulled the plug on it and tried again, lost patience after an hour.
Now I had the idea of maybe locking and unlocking the boot loader would help things.....not sure why I thought this. Anyway, now it seems to hang on the unlock bootloader screen.
So my question now - am I screwed?
- anything else to try?
- is it really "hanging" or do I need to give it more time?
- have I screwed myself even more by now locking my bootloader and flashing the stock recovery?
Any help would be very much appreciated....
Some new additions and new insights from the reddit android community:
- this probably has nothing to do with CM9. My phone has been wonky for about two weeks - random reboots, sometimes rebooting into recovery. That's why I thought I'd throw on the latest nightly and do a fresh wipe yesterday.
- There's definitely something up with /data. Anytime I tried wiping all/factory reset in cwm recovery I got errors about not being able to mount /data or being able to find files in /data
- basically anything I do involving /data partition causes the phone to lock-up -- flashing the boot.img and recovery img worked, but not system. Also, I think the reason I can't re-unlock the bootloader is because during the unlock process it tries to do a factory reset/data wipe
Basically I think there are two things I need to know if I can do - 1) unlock the bootloader again, via some way that won't try to reset the /data partition and thus won't freeze the phone. 2) try repartitioning /data
I really hope I didn't screw myself by locking the bootloader. I'd actually feel a lot better if it was something in my phone that just failed hardware-wise rather than something I could've fixed if I wasn't too quick to try poorly thought out ideas.....
Any help at all would be appreciated!
Possibly (and likely) a corrupted nand flash. Fairly common problem sadly. I'd say it's a good thing your bootloaders locked, no dramas sending it back to samsung. It might've been possible to reset the partitions and flash fastboot images but i don't think i've seen anyone who has done this to sort any similar problem. Hopefully your phones still under warranty
Well thank God that it turns out that I'm still on warranty.....sending the phone back to Samsung tomorrow.
Like you said, it's actually a good thing the bootloader is now locked and the stock boot img and recovery img are now back on! Hopefully this makes it more likely that they weren't turn away my phone.
I've yet to hear someone not getting work done under warranty because of an unlocked boot loader but it's always good to have it as stock as can be. Hope they don't take too long with your phone.
Harbb said:
I've yet to hear someone not getting work done under warranty because of an unlocked boot loader but it's always good to have it as stock as can be. Hope they don't take too long with your phone.
Click to expand...
Click to collapse
I bricked my nexus s 4 days before Christmas last year... and i was using a custom rom obviously with an unlocked bootloader and custom recovery image, and i handed it to vodafone, and guess what? they repaired without asking any questions, and the day before Christmas! sooo happy maybe because i was thirteen then, they didn't suspect a thing
Hi
Was running CM10 nightly from 12 Dec. Bluetooth froze while in car. I rebooted phone. It never came back up after booting, just looping Cyanogenmod logo.
Went into recovery, did a Nandroid, restored my previous backup from the 11th. Still looping Cyanogenmod logo.
Got home. Reflashed stock kernel. Went into recovery and flashed CM10 stable after wiping. Comes up with HTC logo, then black.
Tried to go back into recovery. Comes up with HTC logo, then goes black.
Now it lets me into fastboot, and into the bootloader menu, but recovery does not work. Neither does booting normally. Tried reflashing kernel AND recovery (stable TWRP). It just keeps looping the HTC logo.
HBOOT is 1.14.
Help, please. I'm going to destroy this piece of ****.
If all else fails, run a RUU and skip the thread.
yea, just ruu. i ruu'd a few days ago for kicks.
some car chargers and even wall chargers can make ur phone go wonky, my old moto backflip would randomly press buttons if i used a non-motorola charger.
on a side note, i never used the word "wonky" until this forum.
try running "fastboot erase cache"
also try a clean install instead of restoring nandroid, im assuming your also fastbooting the boot.img from all your nandroid backups. if not they probably wont boot.
strange...
I would say ruu and retry as well.. Sometimes accessories can make a phone go haywire.. Besides the phone is not a piece of crap.Roms can never give you complete stability while stock unrooted can.
Yep. Thanks. Had to start from scratch with Sense again. Now on CM10 stable (and stable CM10 kernel). Hopefully it doesn't lose its mind again, I'm going overseas soon. Sigh.
For anyone who has a similar catastrophe - Titanium recovered most (but not all) of my apps from my TWRP backup. I guess my data partition was slightly corrupt. AppExtractor restored my SMS database from the backup too.
I hate phones.
Passa91 said:
Yep. Thanks. Had to start from scratch with Sense again. Now on CM10 stable (and stable CM10 kernel). Hopefully it doesn't lose its mind again, I'm going overseas soon. Sigh.
For anyone who has a similar catastrophe - Titanium recovered most (but not all) of my apps from my TWRP backup. I guess my data partition was slightly corrupt. AppExtractor restored my SMS database from the backup too.
I hate phones.
Click to expand...
Click to collapse
I always export my contact list to /sdcard if a change is made and then backup to google just in case
Passa91 said:
Yep. Thanks. Had to start from scratch with Sense again. Now on CM10 stable (and stable CM10 kernel). Hopefully it doesn't lose its mind again, I'm going overseas soon. Sigh.
For anyone who has a similar catastrophe - Titanium recovered most (but not all) of my apps from my TWRP backup. I guess my data partition was slightly corrupt. AppExtractor restored my SMS database from the backup too.
I hate phones.
Click to expand...
Click to collapse
I'd suggest keeping a boot.IMG and a stock ROM on the SD card along with adb drivers so you can fix it with a computer without downloading anything.
Sent from my Nexus 4 using xda premium
So here is the situation.
Regardless what Rom I flash, the phone works fantastic up until the first time you try to reboot it. At that point it gets past the samsung flash screen and gets stuck on the flash screen of whatever rom I'm running. I've even left it on like that for an hour and it never changed. The only way I'm able to get out of this is to reboot into recovery with a battery pull and do a data/internal storage wipe.
I've even tried odin'ing to stock and when it goes to reboot the phone to reset it gets stuck at that screen.
From recovery if i wipe everything and install the rom fresh it works great. Any ideas what is messed up or corrupted? Gets kinda old having to reset everything just because phone needs to reboot lol.
xRelapse13 said:
So here is the situation.
Regardless what Rom I flash, the phone works fantastic up until the first time you try to reboot it. At that point it gets past the samsung flash screen and gets stuck on the flash screen of whatever rom I'm running.
Click to expand...
Click to collapse
I have pretty much the same issue with any ROM other than the stock Verizon. I can restore that and everything is fine. I can flash a ROM, flash GApps (if needed) and everything is fine...but restart and yep..hangs at splash screen. If I try a standard wipe data, it fails. I have to do a format of internal memory and then I can proceed to restore or reflash. Kind of a pain in the ass because I really want to run something other than stock. Whoever can solve this problem will be a hero!
Maybe this will help you
Might be a bad partition, a rare problem to all. Maybe this will help you, do this at your own risk. Read first the thread before making a move.
[HOW-TO] Unbrick your soft bricked Galaxy S III (+ bootloader brick)
Note: You know the responsibility when you root your phone, I am not nor them who created this thread have responsibility to your phone, it is your choice.
skyss07 said:
Might be a bad partition, a rare problem to all. Maybe this will help you, do this at your own risk. Read first the thread before making a move.
[HOW-TO] Unbrick your soft bricked Galaxy S III (+ bootloader brick)
Note: You know the responsibility when you root your phone, I am not nor them who created this thread have responsibility to your phone, it is your choice.
Click to expand...
Click to collapse
Gonna go ahead and read through that and try it, not much to lose at this point. I'll keep you guys updated if it works or not
xRelapse13 said:
Gonna go ahead and read through that and try it, not much to lose at this point. I'll keep you guys updated if it works or not
Click to expand...
Click to collapse
Please do...I am interested to see what happens but not ready to try it yet as I am going on vacation and need my phone at the moment instead of bricking it...LOL
I actually had this problem when I just did the regular wipe in TWRP (the one that maintains the internal SD card). When I did an advanced wipe and did everything, excluding the recovery and external SD, things went back to normal.
Used the Unbrick thread and it fixed the problem. Thanks!
Just wanted to post this update for anyone else who had the problem.
Hello!
I can no longer flash anything to my GT-P5110, even factory reset has no effect. The internal storage seems to be read-only.
I think this is a longer story: About one year ago the stock firmware became incredibly slow, to the point that processes started to force close, then my user data was lost, and after factory reset the tablet went into endless boot loop.
So I decided to give CM10 a try and it worked flawlessly. The tablet was fast again. I even could upgrade to CM11 later. But around 2 month ago, only sometimes processes started to force-close or the tablet randomly rebooted itself - mostly during charging. I left it that way in the charger for some days because I had no time to bother with that issue. Then, I tried to factory reset my device only to find out that this has absolutely no effect. Installing app updates: No effect. Changing system settings: No effect. And apps start to force-close at an insane rate short after boot. The device is unusable. My could only shut down and reboot into recovery. I left the tablet lying around, turned off, out of charger, for 2 months. Now I tried to investigate:
When I "adb shell" into recovery and call dmesg, I see lots of these lines:
Code:
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
I think something is really broken with the internal storage. I tried to flash a newer recovery but it has no effect, even when done from download mode.
Factory reset sometimes fails with an error. Reinstalling CM fails with an error. Wiping cache seemingly succeeds but I'm sure it has no effect. I tried installing SlimRom instead which seemingly succeeds, too - but after reboot I'm greeted with the CM boot logo again.
I tried to flash stock firmware with Odin. It is very very slow, runs for about 15 minutes, then fails at around 50%. Of course: That "half flashed firmware" does in no way affect the device: It still boots CM11 "without problems", then a few seconds after finishing boot (showing home screen), force-closes start to pop-up.
What should I do? I suppose the device is out of warranty for a few weeks or months, now. And even when not: It has been flashed with CM, the triangle counter is not zero. I suppose that combination of problems (read-only/failing storage, non-stock firmware) voids warranty in a way that Samsung will deny any repair. If at least I could return the device to stock firmware things would be different maybe.
Any ideas what I could try? Is it possible that the internal storage is simply fried? fsck'ing the partitions shows no errors, just the data partition is unclean with unwritten journal data but all data is readable. So the internal storage has probably not died. It just sticks to read-only mode for whatever reason.
I've found some posts with similar problems but those seem to be about older Galaxy Tab 1 devices built 2011 or before.
Just reading over this and it sounds very similar to what I'm currently facing, which is doubly annoying as no one else has chipped in a solution
I had reboot issues with my Tab2 10.1 (GT-P5110) on stock so after realizing I'd need to factory reset bite the bullet and rooted so I could use CM10.
Had occasional reboots but nothing I couldn't live with however from yesterday evening the tablet is seemingly stuck in a boot loop. It comes on, some apps fire up and an update starts. Sometimes apps force close then BOOM I get the boot splash screen.
I've tried factory reset in recovery (CWM 6.0.2.7) to no avail and wiping just about everything which also had no noticeable effect as all my settings and the rom are still the same when I get back in (albeit briefly!).
I've tried flashing new recovery via ODIN which reported a success however that also didn't appear to take. I'm beginning to think it some serious file system or storage corruption ;(
Same problem here...
Hopefully someone can come up with a solution or at least a cause. I've tried to Odin every recovery available for my 5113 and nothing has taken. I'm currently on Omni with cwm and tried to update to the latest cwm and twrp and aroma installer yet nothing takes. I too rooted because of the incessant bootloops about 3 months ago.
bigg fella said:
Hopefully someone can come up with a solution or at least a cause. I've tried to Odin every recovery available for my 5113 and nothing has taken. I'm currently on Omni with cwm and tried to update to the latest cwm and twrp and aroma installer yet nothing takes. I too rooted because of the incessant bootloops about 3 months ago.
Click to expand...
Click to collapse
For what I can tell, my device is effectively read-only. Even in download mode (Odin) I cannot even flash a different recovery (tried to flash TWRP, still boots CWM).
hurikhan77 said:
For what I can tell, my device is effectively read-only. Even in download mode (Odin) I cannot even flash a different recovery (tried to flash TWRP, still boots CWM).
Click to expand...
Click to collapse
exactly, can't even uninstall an app. It's as if it boots from a permanent back up because even deleting pictures or files isn't permanently successful. You can uninstall and delete to your hearts content, get false hope, and get crushed after it reboots and everything is unchanged
Not looking very optimistic for this I was getting a similar inkling that it's gone into a permanent RO mode as not even the wipes from recovery have an effect. I'd also tried un-installing apps as I noticed one updating and thought it was crashing it however even when it did fire up and I disabled WLAN to stop Play Store auto-updating and removed the app on the next reboot cycle the app was back:crying::crying:
I fear I may have a big white paperweight....
Sounds like the internal partitions might need to be completely reformatted. This CAN be done through recovery, but is tricky... However without actually having your device in my hand I'm not sure 100 what the best course of action would be. Try searching for the commands to format (or maybe someone else will post them) or maybe PM me for them but no promises. I won't post them publicly on XDA because honestly there are too many users who do stuff like one-click root and don't actually know what they're doing and I don't want to be in some way responsible for someone following the command wrong and bricking their device for good. I don't need that on my conscience. Personal choice.
Sent from my Nexus 4 using XDA Premium HD app
shakatu said:
Sounds like the internal partitions might need to be completely reformatted. This CAN be done through recovery, but is tricky... However without actually having your device in my hand I'm not sure 100 what the best course of action would be. Try searching for the commands to format (or maybe someone else will post them) or maybe PM me for them but no promises. I won't post them publicly on XDA because honestly there are too many users who do stuff like one-click root and don't actually know what they're doing and I don't want to be in some way responsible for someone following the command wrong and bricking their device for good. I don't need that on my conscience. Personal choice.
Sent from my Nexus 4 using XDA Premium HD app
Click to expand...
Click to collapse
Would this method be any different to the way it attempts to reformat the internal partitions when you select to format the various mounts from CWM? If so I'm more then willing to give it a go as I really have nothing to lose as the damn thing is useless atm!
shakatu said:
Sounds like the internal partitions might need to be completely reformatted. This CAN be done through recovery, but is tricky... However without actually having your device in my hand I'm not sure 100 what the best course of action would be. Try searching for the commands to format (or maybe someone else will post them) or maybe PM me for them but no promises. I won't post them publicly on XDA because honestly there are too many users who do stuff like one-click root and don't actually know what they're doing and I don't want to be in some way responsible for someone following the command wrong and bricking their device for good. I don't need that on my conscience. Personal choice.
Sent from my Nexus 4 using XDA Premium HD app
Click to expand...
Click to collapse
Good call......Smart move?
help!!
same issue here , sort of .. i have stock rom and stock recovery and i cannot flash CWM .. no matter how many times i try through ODIN or hemidal nothing changes.. any idea what is going on here?
PMs have been sent. Hopefully it works.
Sent from my Nexus 4 using XDA Premium HD app
im also having this issue with my galaxy tab2 7".. help is badly needed
Well, the proposed fix I had didn't help. Was worth a shot...
Sent from my Nexus 4 using XDA Premium HD app
hope someone finds a solution for this.
No Access to ADB
shakatu said:
PMs have been sent. Hopefully it works.
Sent from my Nexus 4 using XDA Premium HD app
Click to expand...
Click to collapse
Hi Shakatu,thanks for the PM, however, my device in ADB is unauthorised, so wont let me get into shell. Is there a way around this please?
sunnytimes said:
same issue here , sort of .. i have stock rom and stock recovery and i cannot flash CWM .. no matter how many times i try through ODIN or hemidal nothing changes.. any idea what is going on here?
Click to expand...
Click to collapse
Unmark "Auto Reboot" in Odin when CWM is flashed... Stock room overwrites it during start.
After flashed CWM start in Recovery mode and flash new ROM.
this is offtopic in this tread
same problem please help me... :crying:
seagman said:
Unmark "Auto Reboot" in Odin when CWM is flashed... Stock room overwrites it during start.
After flashed CWM start in Recovery mode and flash new ROM.
this is offtopic in this tread
Click to expand...
Click to collapse
i have tried that 100 times .. its also exactlly what this thread is about , not being able to flash because nothing changes..
sunnytimes said:
i have tried that 100 times .. its also exactlly what this thread is about , not being able to flash because nothing changes..
Click to expand...
Click to collapse
same here too, i have same issue.. unable to flash or do anything to my phone....
Probably this is the end for our tab. As off now the tab is useless.
Sent from my GT-N7000 using XDA Free mobile app