Database Info

Recessed front camera?

Hey guys, I had a question about the front camera on the One X.
I have mine, and it seems that the camera & glass is recessed inside of the casing about 2mm. I was wondering if it's supposed to be this way or not? Its quite a deep recess, its impossible for me to clean dust off the lens without using something like a toothpick because it is so deep and small. So I'm just wondering if this is normal or not. Thanks

Normal. Mine is the same way.
Sent from my HTC One X using Tapatalk 2

Ddot196 said:
Normal. Mine is the same way.
Sent from my HTC One X using Tapatalk 2
Click to expand...
Click to collapse
Confirmed, same here.

Okay thanks, just had to make sure. Seems kind of strange since it makes it very difficult to clean

Lol I didn't wanna sound like a tweaker
But I tried cleaning it and it sucks

It's a bad design element for sure. I use what looks like a little makeup application brush to dust it out.

Yup. Only part of my phone that doesn't look brand new...
Sent from my HTC One X using XDA

roltzje said:
Okay thanks, just had to make sure. Seems kind of strange since it makes it very difficult to clean
Click to expand...
Click to collapse
I think the point of it being recessed is so you DON'T have to clean it. Usually you get finger prints all over the lens and grease because most cameras are flush with the front....with this deisgn, the lens avoids that

You could always spray some computer cleaner/compressed air in there
Sent from my HTC One X using XDA

I use a Qtip...
Sent from my ROOTED HTC One X using xda premium

Mine has been away for repair. I never noticed before, but although mine is recessed there appears to be nothing protecting the camera module. If I look from the side there is a small gap to the inside of the housing. Is this right?? I suspect the repair centre has screwed up and forgotten to put something in there. If I shoved something in there to clean it I would basically be cleaning the tiny lens of the camera.
Can anyone post a picture of what it's supposed to look like as I have nothing for comparison.
Also they (Regenesis) have left a gap in the seal between the top of the LCD panel and the bezel AND the original fault of a stuck pixel is fixed only to the extent that there is another stuck pixel elsewhere.
Am I within my rights to demand a brand new unit from HTC? I think it's unacceptable to be messed around like this, bearing in mind the expense of the unit. I also totally distrust the capabilities of Regenesis, based on this and my experience sending an HTC Sensation away for repair last year.

[Q] Replacement Digitizer Problem

So I finally replaced my cracked screen and I've been having issues with my new digitizer. It's one of the LG digitizers, not the ones that say T-Mobile at the top. When you touch the extreme left side of the screen, it acts like you're touching the extreme right side of the screen at the same time. It's very weird - when I try to capitalize, it also backspaces, and my a's all have l's after them - stuff like that. It's like that all the way from the top of the screen to the bottom.
I got in there and cleaned a couple of specks of dust that I had accidentally left between the digitizer and LCD screen and it didn't seem to help. I used compressed air to clean the contact where the digitizer ribbon cable connects to the motherboard and tried to get the ribbon cable itself to sit under the motherboard nice and straight (I had a little trouble with it the first time and it could have been crooked, I guess, but I'm not sure if that would even matter.) I've also tried soft reboots, removing the battery, full wipes, and even have experimented with a few different ROMs. Acts exactly the same.
What do you guys think? Do I have a bad digitizer or is there something else I could try to get it to work properly? Thanks!

I buy broken phones of Craigslist and fix them. I have put digitizers on 4 g2x as of yet never had that problem. I'd make sure the connections were nice clean and seated correctly. I see you've done that so my conclusion is that you have a faulty unit. Run a calibration app and see if that helps
Sent from my LG-P999 using Tapatalk 2

I had bought a digitizer with the LG logo on it and it was not as senseative to the touch and as well when touching the left or right sides of it where off a little. I used the ones with the T Moble logo and all works like new.
Sent from my LG-P999 using xda premium

Different digitizer replacement issue
Stopfakn said:
I buy broken phones of Craigslist and fix them. I have put digitizers on 4 g2x as of yet never had that problem. I'd make sure the connections were nice clean and seated correctly. I see you've done that so my conclusion is that you have a faulty unit. Run a calibration app and see if that helps
Sent from my LG-P999 using Tapatalk 2
Click to expand...
Click to collapse
Hi, my screen cracked, so I got a replacement digitizer and installed it. When I reassembled the phone, it worked fine, except the buttons at the bottom (home, back, etc.) and the bottom 15% of the touch screen do not register. The rest of the touch screen works fine.
Do you know if that part is connected differently from the rest of the phone? Or any other reason it might be broken.
This may be dumb on my part, but my package didn't come with adhesive, so I used superglue. Could that be messing up the sensor somewhere? Or is it not likely that?
Any thoughts/comments would be greatly appreciated.

You probably got some glue in the wrong place. I used 3M double sided adhesive, that way I could be exact with the placement
Sent from my LG-P999 using xda premium

Superglue + Electronics = BAD!
Sent from my LG-P999 using xda app-developers app

justjackyl said:
Superglue + Electronics = BAD!
Sent from my LG-P999 using xda app-developers app
Click to expand...
Click to collapse
Hah what he said.
You should never use glue of any sort on electronics. If the manufacturers don't do it, then you surely shouldn't.

Anybody tried these replacement screens?

and how much trouble would it be to install one? Only the outer glass I know.
http://item.mobileweb.ebay.com/view...cmd=VIDESC&index=2&nav=SEARCH&nid=37627158673
Sent from my SAMSUNG-SGH-I727 using xda app-developers app

I got one, it went in all right, but was a pita to get the oldscreen off. Its pretty much glued on, has an adhesive gasket, and requires breaking the old screen to pieces separateto . The new screen never came with the outer seal, but i haven't had any issues yet. Its been in about two months.

I wouldn't trust eBay for a screw driver

breeze1000rr said:
and how much trouble would it be to install one? Only the outer glass I know.
http://item.mobileweb.ebay.com/view...cmd=VIDESC&index=2&nav=SEARCH&nid=37627158673
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
Click to expand...
Click to collapse
See this video.
http://www.youtube.com/watch?v=k6Y6an6D2PE

m4570d0n said:
See this video.
http://www.youtube.com/watch?v=k6Y6an6D2PE
Click to expand...
Click to collapse
Thanks for the video....hopefully I can get my new screen installed without any problems......should be here next week sometime and I will post results IF I install it right.....
Sent from my SAMSUNG-SGH-I727 using xda app-developers app

I replaced my screen and the LCD. They are pretty tightly glued together but my glass was fine, it was the LED that was shot. I didn't watch the video but I can give you some of my experience. I got the replacement from China. It came with magic marker blocking out the 2 logos. It was on the plastic covering and there they were when I removed it. I didn't watch the YouTube I was watching past the point where he said press anywhere its broken anyway. The next sentence was "except here". I can tell you if press there you will hear an 8.95 snap. Its the power strip to the lighted home buttons. So I put the screen on and waited for it to arrive. I also got some 2mm double-sided tape this time. I knew to get it really hot also, even though I hadn't really pressed it home. I looked at the speaker hole and though that would be a good place to grab- DON'T. It snapped off the top part of the replacement screen. I thought oh well I might as well plug it up before I trash it. I lucked up and it didn't get into the LCD-YET. I'm using it now and there is one crack in the glass but a perfect picture. So, buy 2 or 3mm tape, do not press on lower right side where you see copper. Get it hot and then get it hotter- hairdryer. Take your time and remember the connectors. You understand that what you had a link to is just the outer glass and if the LED isn't broken you'll have an interesting time separating the two.
Oh, I put electrical tape where the top glass broke and its underneath the top of the plastic protector I bought. You'd have to be looking for it to notice. Sometimes you're the squirrel, sometimes the nut.
Good Luck
Sent from my SAMSUNG-SGH-I727 using xda app-developers app

Well I failed at replacing the screen.....the digitizer cracked wen trying to separate the screen from it and yes I heated the screen to where it literally burned my finger...haha.....so now I'm stuck with a replacement screen I have no use for and had to shell out another $150 for the digitizer. I shudve just done that in the first place.
Sent from my SAMSUNG-SGH-I717 using xda app-developers app

Sell it on eBay 20 bucks cheaper.
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2

No Screen! Cover Replacement Gone Horribly Wrong! Help/Buy/Suggestions?

SMh... broke my digitier/lcd on my One X today!
Was gonna replace my back housing because it was cracked and had scuffs to put a white one on,
but when I was doing the first step I went into the wrong slit and slid my tool in between the LCD/Digitizer!!
Only a few centimeters from the edge, guess it was enough.
Now the screen doesnt turn on AT ALL!! Phone still boots and capacitive buttons light up and vibrate
I'm not sure where to start, I hope I can get it to work still but I dont know what to try now.
Im a noob, but the only thing I can think of is to dissamble the whole phone and then
blow dry it and separate the LCD/Digitizer and put them back together after inspecting.
This happened by sliding a guitar pick in between the LCD/Digitizer.
I only went in a few centimeters from the edge until I realized I was doing something terrible wrong.
I was trying to disassemble my One X.
It still works, I plugged in MHL adapter and it works, could navigate normal, just that the LCD doesnt turn on.
Click to expand...
Click to collapse
A) $75+ for a new screen and attempt to fix myself?
B) Sell it for as much as I can? $220?
C) Try to get AT&T/HTC to replace it even tho I rooted 2.20?

You know how long its been since I read about a Hox issue that hasn't been posted yet???? I feel bad, that sux, it really does, but this was by far the funniest thing I've read about in a while
Sent from my Nexus 7 using Tapatalk 2

I did the exact same thing you did! That's why I've got two HOX now. I had to purchase the LCD/digitizer combo. All fixed now. I still have the digitizer screen on my desk. Sucks I know.
Sent from my One X using xda premium

you can try that but doubt it'd fix anything. Plus the LCD and digitizer are seriously bonded together tight so it'd be hard to take it apart fully without breaking the glass. I've replaced my LCD/digitizer twice, and while it's not impossible, it's still very tedious and risky. So if your gonna do it yourself I'd suggest making sure the place you get it is atleast somewhat reputable so you don't get another faulty screen, and don't use super glue to bond the LCD to the housing! (lol that was what I did with my first screen and it destroyed the screen). And be prepared to be left with some more scuffs on your housing. Otherwise sending to HTC shouldn't be a problem, even with root I think it's fine. It's just a screen repair, its not like root could cause really screen damage. Good luck though on whatever you decide.
Sent from my One X using xda premium

thanks for the reply, um do you think HTC would fix for free if I play dumb and say one day it just stopped turning on?
I've decided not to try to separate the LCD from the digitizer, way too work.
and an xda member said he'd sell me his lcd+digi for a good price but its a HTC Branded one instead of AT&T, i think it will work the same tho,

I got the HTC logo digitizer/lcd. Worked fine vs the original att one
Sent from my One X using xda premium

alright good to know! I prefer it to say HTC anyhow since im not even with AT&T! Im T-mobile!
so you really did the exact same thing as me!? guitar pick in the wrong hole!?
How far did u push in and try to separate it til you noticed u messed up BIG TIME?
I was in denial for a good 10 minutes =( still kinda am... smh

I went a little farther than you and got angry though. Totally destroyed it. Lol! Couple things. Make sure you get the adhesive strips. There is a metal casing that goes around that LCD that likes to pop out if not glued properly. And I got mine from repair universe. Not perfect but pretty cheap. Only issue is captivate button lights don't transfer over, and I had to silicone the edge of the LCD to the digitizer cause it started getting dust between them. Pain to say the least. I taken these apart enough now. I'm comfortable with it.
Sent from my One X using xda premium

u bought the LCD+Digitizer and the capacitive buttons still didnt turn on? Hope mine will work.
Also can u point to me which YouTube tut was the most helpful for you?
I wish there was some way to fix the LCD I have now tho, still in good condition aesthetically =(

Yeah it sucks that most newer devices really bond the LCD and digitizer tightly. Once (if) you take it apart you'll realize what we mean. Its possible but very unlikely with original screen. And taking the LCD off the housing is near impossible to do without breaking the LCD in my experience too. So make sure to get LCD+digitizer. And as far as sending it to HTC, I'm sure you could try but once they figure out what you did I'm sure they'll charge you (why wouldn't they? ). There was an amazing YouTube video made by some company (I think it was irepairfast) that I used but after many people complained about their service here on their one x, they removed it. So sorry, just look around for some good ones.
Sent from my One X using xda premium

I agree with what xaey said. Depending on the LCD/screen you get the captivate buttons may or may not have the little fiber optics on them. I just went with the cheapest one I could find cause I'm a tight [email protected]%. There are NO good videos that I could find on tear apart and none on putting it back together. Take you time and keep an inventory of what you do. I lost a screw and its still missing inside the repaired phone.
Sent from my One X using xda premium

oh well it should save some power then right? im a cheap buyer too!
these tuts seem pretty good!
http://youtu.be/FxbjQbi1tAY
http://youtu.be/OIeO0DueMcg

When replacing it, just take them optics out of the original, it has very lightly adhesive but it should come off easily and then put them on the new one if it doesn't haven't them already, it should still be a bit sticky to do so. Another problem is possible light leakage (you'll know what I mean if it happens, basically more light shines through than just on the buttons). This happened to me, which is why I don't keep my capacitive lights on. Worst part is you won't know until you turn it on unless you can connect the screen to circuit without bonding it to the housing yet.
Sent from my One X using xda premium

alright I'll try that if it doesnt come with capacitive lights. will attempt to replace it next week. I hope I can do this correctyl!!

Well put xaey. I tried to transfer those over and there was way too much light bleeding from the side and bottom. Plus they were a pain to get in there. I tore that thing apart 4 times. Lol trial and error. So I just put some sealant over the captivate area. Unfortunately that does not disable the lights to them.
Sent from my One X using xda premium

subarudroid said:
Well put xaey. I tried to transfer those over and there was way too much light bleeding from the side and bottom. Plus they were a pain to get in there. I tore that thing apart 4 times. Lol trial and error. So I just put some sealant over the captivate area. Unfortunately that does not disable the lights to them.
Sent from my One X using xda premium
Click to expand...
Click to collapse
Lol yeah I know what you mean. I ended up putting some black electrical tape over where the light bleeding was on mine (just under the capacitive buttons) before putting the screen in... and it didn't help much, it just looked more weird looking at it from different angles haha. So I just keep the lights off.
Sent from my One X using xda premium

eww I do not want to see leakage from the bottom!
Hopefully i get lucky and only have to take apart once and be done with it!
I've only taken apart a HTC Dash a few years ago.
Excited to put my hand eye coordination to the test

smh... noticed wifi/data pins came off also so I am SOL!!
any suggestions on what and how to replace those pieces on the motherboard?

Witch ones? Data pins?
Sent from my One X using xda premium

im not even sure what the term for these are, the metal on the motherboard that touches the gold areas on the back cover?
I must have pulled the phone out too rough or something but they came off the mother board.
my wifi only gets 1 bar, DL speed of 3mbs
data doesn't connect, can still call text.
this video shows the areas on the phone
http://www.youtube.com/watch?v=7NZXM_O5srw

Air Bubble Inside of Screen

I recently bought a used HTC One S. Its in great shape and I've only had it for a few months. A few days ago I noticed an air bubble on the left side of my screen. At first I thought it was a crack or a scratch but the glass on my phone is fine. It keeps getting larger and I don't have any money for a new phone at the moment so I was wondering if anyone else had this problem or knows how to fix it?

ThatOneKidRobby said:
I recently bought a used HTC One S. Its in great shape and I've only had it for a few months. A few days ago I noticed an air bubble on the left side of my screen. At first I thought it was a crack or a scratch but the glass on my phone is fine. It keeps getting larger and I don't have any money for a new phone at the moment so I was wondering if anyone else had this problem or knows how to fix it?
Click to expand...
Click to collapse
Is it under the screen protector and not the screen itself perhaps?
Sent from my rotary phone

the4biddendonut said:
Is it under the screen protector and not the screen itself perhaps?
Sent from my rotary phone
Click to expand...
Click to collapse
I don't have a screen protector on my phone. Its in the screen its self :crying:

I used to see this on the old acclaims a lot. Best bet is a blowdryer to reheat the glue under the digi. Let it cool slowly though or it can crack (though it's unlikely)
Otherwise it'll need a new digitizer
Sent from my KFSOWI using xda app-developers app

kyleberry.graphics said:
I used to see this on the old acclaims a lot. Best bet is a blowdryer to reheat the glue under the digi. Let it cool slowly though or it can crack (though it's unlikely)
Otherwise it'll need a new digitizer
Sent from my KFSOWI using xda app-developers app
Click to expand...
Click to collapse
I've tried this because I saw it on a form for one of the older iPhones and it made it worse!! I'm not really worried about anymore. Guess I'll have to wait for my upgrade later this year

ThatOneKidRobby said:
I recently bought a used HTC One S. Its in great shape and I've only had it for a few months. A few days ago I noticed an air bubble on the left side of my screen. At first I thought it was a crack or a scratch but the glass on my phone is fine. It keeps getting larger and I don't have any money for a new phone at the moment so I was wondering if anyone else had this problem or knows how to fix it?
Click to expand...
Click to collapse
I have the same issue .. just started for me... last year my broken screen had been replaced...

Theoretically this will occur when the digitizer is getting apart from the screen. As you may know, the screen we see it's composed from several layers glued together. The digitizer is the last layer, the one we touch and transmit our touches to the OS. This is also the part that usually gets broken (if the shock wasn't too big ofc to break the actual LCD screen).
You could go to a service, they are used to replace such parts and they could glue it back. It might be possible that your device had the digitizer replaced in the past and it was not properly glued as it have been initially in the manufacturing plant and that's why you have the issue