Related
Below is the procedure to FACTORY REST, ROOT AND MArket installation for COBY KYROS MID7010 or MID 7010 Tablet owners stuck at white boot screen OR android OS not loading after any manipulation with the firmware OR interested in rooting and installing google market.
FACTORY RESET Steps:
1. Turn OFF the device
2. Make sure its turned OFF
3. Press and hold simultaneously POWER + BACK + HOME buttons (as in third Pic)
4. The device turns on with COBY logo, keep pressing......
5. After about 15 to 20 seconds the COBY LOGO display changes and prompts to press the keys again within 5 secs to factory reset the device.
6. LEAVE the power button now while still pressing HOME and BACK keys
7. FActory reset is initiated!
TO INSTALL MARKET AND ROOT:
1. Enable adb debugging on your tablet,connect to pc wait for driver installation if any. Run SuperOneClickv2.3.2-ShortFuse.zip > choose advance> driver install
2. Will prompt to force install drivers ( if the adb device drivers not available), accept and sit back! the program will not respond for a while 10-15mins and prompts back that the drivers are installed.
3. Run root from the above software (clicking root tab)
4. Open root explorer or any file browser accepting root, browse to system/app copy all files in attached folder (apks) here, if prompts to rewrite( do not allow!)
5. Change permissions of the copied files as in other apks in system/app folder.
6. Google market app appears in app drawer.
7. Run and Enjoy!
thnks for the useful thred
thanks a lot for this thred since no one is taking care of this model "7010" .. my kyros 7010 stop working and freez on android booting screen a did the method you post here but i got this message
" Unexpected updater mode! Pleas reboot your device"
could you pleas support me with any help since i am olmost about to lose the hope to get my Kyros back to life
Follow the buttons, you arent pressing hard the back button. its HOME + BACK+POWER all three buttons altogether. until the coby screen changes to reset request as in pics. Ask someone to press the power button while you press the front two. UNTIL THE COBY LOGO display changes (15 to 20 seconds).
the same problem
really i tryed it ten times and got the same message " unexpectaed updater mode please reboot your device"
it gives me Penguin logo "Linux logo" befor this message - this logo is normally comes even befor it stop working
pressing the power button + home button only displays your message. You are definitely not pressing back button hard enough or its broken?!?. TRy pressing power than reset pin at back together. a white screen appears release both buttons and try the three button combination again.
YOU must apply steady pressure on the three buttons for 20 seconds till the coby logo screen automatically changes. Ask someone else to help you with it. THIS KEY COMBINATION DEFINITELY WORKS!
the same problem
i did the power + reset and yes it gives me a white screen then use the three buttons "i am sure i pressed them well"
the coby logo screen changes to Penguin logo "Linux logo" and it gives me the same message
i feel that i am breaking your head but you are the only hope that i have no more help on this model .. so can i do that throw ADB i did root it using adb and whin i tybe # recovery it gives me (android system recovery <e3>) with 3 choces to restor or reboot somthing like that but non of them are working i can choose between them but i cant select or confirm i tried all the buttons but no action
when do you release the three buttons? Are you sure its mid 7010 there is no recovery rom partition in mid7010 as far as i know.
i releas them after i swe the message "unexpectaed updater mode please reboot your device" and i try to wait more than one min as well
and yes i am sure it is coby kyros MID 7010. i got it from Dubai as a present
i know there is no recovery partition as i read it a lot on the internet.
so do u have any recovery rom for that model or any other way to install system on it???
Since there is no recovery partition than A kernel is required to repartion the partition table WHICH IS NOT EASY and since there is a way to factory reset why would one bother. i don't understand how you got to recovery menu when there isnt any? Besides have retried the steps and they work all the time. MOSt probably your return key is damaged!
rooting
i did everything and then when i connect the device via usb (after debugging n since there is no unmount) superoneclick does nothing, no driver update nothing, it just stays there, n if i click root, it hangs(super). m i doing something wrong?
it hangs! thats the point..... it takes time. Does it prompt to force install drivers yes:no?
the program will not respond for a while
Click to expand...
Click to collapse
Where does it freeze? ADB kill server> ADb start server>?
stuck on android logo after factory reset
mughalgxt said:
when do you release the three buttons? Are you sure its mid 7010 there is no recovery rom partition in mid7010 as far as i know.
Click to expand...
Click to collapse
Hi, i also have the same problem. Im stuck on the android logo after i did a factory reset. I tried the three button combo u instructed but im stuck always on the coby logo if i hold the three button.
Any help will do. Thank you
kernel
mughalgxt said:
Since there is no recovery partition than A kernel is required to repartion the partition table WHICH IS NOT EASY and since there is a way to factory reset why would one bother. i don't understand how you got to recovery menu when there isnt any? Besides have retried the steps and they work all the time. MOSt probably your return key is damaged!
Click to expand...
Click to collapse
aftry month now of trying every thing to get this kyros to life again but failed ... i think as u said a kernel is the only hope now .. hope i found some one to help in how can i do that
magus1982 said:
Hi, i also have the same problem. Im stuck on the android logo after i did a factory reset. I tried the three button combo u instructed but im stuck always on the coby logo if i hold the three button.
Any help will do. Thank you
Click to expand...
Click to collapse
You have to keep holding the three buttons the Coby LOGO display will change after 20-30 secs. ANDROID logo means the reset is done and the OS is loading will take time after reset. blank black screen means the Os cannot load hence factory reset must be done. Which logo are you stuck with?
sherif.afifi said:
aftry month now of trying every thing to get this kyros to life again but failed ... i think as u said a kernel is the only hope now .. hope i found some one to help in how can i do that
Click to expand...
Click to collapse
Your final hope is getting the back button repaired or ask someone else to do the reset procedure for you. No one is going to create a kernel for you. or for coby. try kyros forum website see if you persuade someone for more TECHNICAl support. I believe your tab's back button is damaged.
I have the Coby Kyros MID7010wc and I followed those steps, but it didn`t work - google market icon didn`t show up on apps screens. I tried to run those apks but it always says "application is not installed".
Is there something else that I can do?
did you root the device successfully?
how did you change the permission of the files in the attachment after pasting them into /system/app folder?
did you restart the device after above step?
* You need not manually install anything as it wont work just copy and paste them into system/app, change permissions and restart.
Yes it is rooted - used SuperOneClick
I didn`t understand when you said "if prompts to rewrite( do not allow!) "
if I don`t overwrite the apks it won`t install the files.
Anyway, used root explorer and copied each apk one by one in the system/app folder then changed the permission (checked every fields).
Did you reboot the system after changing permissions? Overwriting all apks in the attachment to system/app is not required rather unnecessary as google framework already exists only missing is phonesky or android market. These steps worked for me try reading other mid7xxxx threads to cross check
I redone everything and it is working as expected.
thanks!
Hi all,
Was wondering if i can get help or a solution to my problem.
I have an advance II novo 7 tablet, First of I''l start at the beginning.
I flashed my tablet and before i did i done a nandroid back up,
now i have realised i have flashed it with the wrong rom for the simple fact when i press
left, my tablet pointer goes right. In my tablet it wont sync with pc nor will it boot in to recovery mode.
All my programmes are missing except terminal and a few others, my tablet will not connect to wifi.
So i can't just download a copy of CWM prem, an install it.
Oh yeah my memory card is full but it's like a virus, i can't access it and as above
everything is back to front. Can i even install or do something via terminal?!?
Any help would be much apprectiated, as at the moment I'm sitting basically with a dead slate.
Kind regards.
Joseph.
From my experience, the custom ROMs have a shortcut to boot into recovery. Press and hold power button, when menu arrives, goto Restart > Recovery, press OK.
Please tell if it helps or not
[Q] Unable to flash Lenovo A660 -> looped during factory reset -> unable to boot
Hello all!
I am having a really strange error with my phone. I can't flash it. Even when it says it's "Downloaded OK" -> green circle in Smart Phone Flash Tool, seems like nothing really happened.
The problem is, machine Lenovo A660 keeps restarting and "updating". Lenovo logo -> Android image with some weird blue shape -> restart. (5-10secs each repetition).
My Factory mode looks like this -> http://imageshack.us/photo/my-images/594/img5854y.jpg/ (power on + volumne down)
This phone came with Etotalk MOD ROM.
Main problem occured, when I've couldn't access my applications -> Application not found error and lost all application icons. Then Google Play said, my account has never been used with this device. So I joined again, "re"installed applications. Some worked, but most of them kept shutting down with errors. So I decided for factory reset via software menu recovery and backup menu (??). Device started to "recovering" and it was doing for 20-30minutes - so I have restarted it.. bearing on mind, that factory reset did not work, as people stated it lasts around 7mins..
Then I have tried to flash it using various boot.img and recovery.img from
http://forum.xda-developers.com/showthread.php?t=1874403 and http://forum.xda-developers.com/showthread.php?t=2104748
but they won't work. Seems like something starts earlier then true recovery tool.
Any help would be appreciated.
Thank you in advance.
Mich
I have found and use stock-modded ROM for this phone, but it really seems like Smart Phone Flash Tool is not flashing this device.
The thing is, I never see that purple bar to come.
I am using only recovery and boot image. After hitting Download I connect phone, which got battery out for few secs, and leave it as is. Red bar fills up, yellow bar fills up and that all, green circle appears.
When I start device, no change has happened. :-/
Somebody help me, please..
Btw, what is that THL and which is on my phone? Do I actually need it?
I am really stuck.
Michalxo said:
If you would have some spare time, would you help me please?
This is my problem described in a deeper way -> http://forum.xda-developers.com/showthread.php?p=37983752
I think, that smart phone flash tool is not actually flashing the device at all.
Your help is probably the last I might get.. in case you know any other phone-expert.
I had this phone for almost a month and a week
PS: I have anohter exactly same phone in case it might help something in something.
Thank you very much in advanced.
Mich
Click to expand...
Click to collapse
You are correct, the standard recovery will not flash the ROM. You *must* first flash a custom recovery using the windows flash utility, and after that you can flash the ROM you linked to.
Read the first two posts in this thread, and the pages it links to, especially the two 'flash' links and the A660 recovery link.
cybermaus said:
You are correct, the standard recovery will not flash the ROM. You *must* first flash a custom recovery using the windows flash utility, and after that you can flash the ROM you linked to.
Read the first two posts in this thread, and the pages it links to, especially the two 'flash' links and the A660 recovery link.
Click to expand...
Click to collapse
Thank you for your help! After some hard battling with some button combinations I managed to get into some "etotalk" rom recovery, which fixed partitioning (using mke2fs tool) and getting clean "old" 4.0.4 android.
Thank you again! Phone is alive!
PS: I am not sure of the combination, but I pressed & hold both volume controls and simultaneously (or few ms later) pressed power on button.
Michalxo said:
Hello all!
I am having a really strange error with my phone. I can't flash it. Even when it says it's "Downloaded OK" -> green circle in Smart Phone Flash Tool, seems like nothing really happened.
The problem is, machine Lenovo A660 keeps restarting and "updating". Lenovo logo -> Android image with some weird blue shape -> restart. (5-10secs each repetition).
My Factory mode looks like this -> http://imageshack.us/photo/my-images/594/img5854y.jpg/ (power on + volumne down)
This phone came with Etotalk MOD ROM.
Main problem occured, when I've couldn't access my applications -> Application not found error and lost all application icons. Then Google Play said, my account has never been used with this device. So I joined again, "re"installed applications. Some worked, but most of them kept shutting down with errors. So I decided for factory reset via software menu recovery and backup menu (??). Device started to "recovering" and it was doing for 20-30minutes - so I have restarted it.. bearing on mind, that factory reset did not work, as people stated it lasts around 7mins..
Then I have tried to flash it using various boot.img and recovery.img from
http://forum.xda-developers.com/showthread.php?t=1874403 and http://forum.xda-developers.com/showthread.php?t=2104748
but they won't work. Seems like something starts earlier then true recovery tool.
Any help would be appreciated.
Thank you in advance.
Mich
Click to expand...
Click to collapse
hi i have the same problem with the same phone,how you solved the problem?
thank you
nicodim23 said:
hi i have the same problem with the same phone,how you solved the problem?
thank you
Click to expand...
Click to collapse
This might no longer be up to date AND I am no expert but when I was "playing" with my A660, I noticed that some (generic) descriptions for flashing, etc. refer to up- and down volume buttons, which (because they are on the right side of the device?) are in some cases mirrored to some of the instructions. In other words, up is down and down is up (if that makes sense).
If I power off the device, I usually first press volume up (and keep it pressed), while then also pressing and holding the power button.
Once the screen comes to live, you may let go of the buttons.
This combination brings me into the CWM Recovery based Recovery Mode. My phone also had the ETOTALK ROM installed ...
Navigation is with volume up / down and item selction is with the power button!
Same procedure with volume down gets you into the "factory Mode" menu, where you can do all sorts of test. However, this mode is also required for some (!) flashing procedures (ofter referred to for adb access).
Scrolling through the entries with volume down. Accepting an entry with Volume Up!
Hope this helps,
Robert
New Lenovo A660
Hallo, I root'ed my new phone with A789_ROW_S106_cybermaus_ICS_V3.1 with SP flash tool.
Every thing was working great until I want to instal v3.21.
I flashed the old v3.1 and I have a problem.
My phone don't power on, but I can flash booting, rocovery.img etc, what can I do to make it working again ??
Now, I see phone in SP FLASH TOOL, I can flash booting, recovery, but phone won't power on.
Is there anything i can do??
DawidMacha said:
Hallo, I root'ed my new phone with A789_ROW_S106_cybermaus_ICS_V3.1 with SP flash tool.
Every thing was working great until I want to instal v3.21.
I flashed the old v3.1 and I have a problem.
My phone don't power on, but I can flash booting, rocovery.img etc, what can I do to make it working again ??
Now, I see phone in SP FLASH TOOL, I can flash booting, recovery, but phone won't power on.
Is there anything i can do??
Click to expand...
Click to collapse
What phone were you flashing?
please with with my lenovo a660
steirx said:
This might no longer be up to date AND I am no expert but when I was "playing" with my A660, I noticed that some (generic) descriptions for flashing, etc. refer to up- and down volume buttons, which (because they are on the right side of the device?) are in some cases mirrored to some of the instructions. In other words, up is down and down is up (if that makes sense).
If I power off the device, I usually first press volume up (and keep it pressed), while then also pressing and holding the power button.
Once the screen comes to live, you may let go of the buttons.
This combination brings me into the CWM Recovery based Recovery Mode. My phone also had the ETOTALK ROM installed ...
Navigation is with volume up / down and item selction is with the power button!
Same procedure with volume down gets you into the "factory Mode" menu, where you can do all sorts of test. However, this mode is also required for some (!) flashing procedures (ofter referred to for adb access).
Scrolling through the entries with volume down. Accepting an entry with Volume Up!
Hope this helps,
Robert
Click to expand...
Click to collapse
I also had exactly the same problem as you, when trying to do a factory reset on my phone too. the vol up+ power button don't work, instead the phone starts in the same looped state, displaying the green android logo & restarting.
somebody please help me out.
DawidMacha said:
.....
My phone don't power on, but I can flash booting, rocovery.img etc, what can I do to make it working again ??
Now, I see phone in SP FLASH TOOL, I can flash booting, recovery, but phone won't power on.
Is there anything i can do??
Click to expand...
Click to collapse
I have the same end result (after a factory reset (unintended) and unsuccesful attemts to put etotalk recovery rom back) i did a "format" from the flash tool): the phone appears dead, it will not power up. the flash tool does recognise the phone, and will download, memory test (it does say: "NAND Flash was not detected" however), etc.
Henkjan_O said:
I have the same end result (after a factory reset (unintended) and unsuccesful attemts to put etotalk recovery rom back) i did a "format" from the flash tool): the phone appears dead, it will not power up. the flash tool does recognise the phone, and will download, memory test (it does say: "NAND Flash was not detected" however), etc.
Click to expand...
Click to collapse
solved!
using the instructions from http://forum.xda-developers.com/showthread.php?t=1943442 I got the phone unbricked, so I could put the original firmware back (thanks to etotalk tech support for that tip) and then upgrade again tothe etotalk ROM.
I have a dead lenovo IdeaTab. It powers up and will hang at the Lenovo screen. The only way out of this is to use the reset button. I have tried to do a wipe/factory reset with no luck. When I tell it to reset to factory default, it hangs up with the android picture on the screen just stays there. Again with the reset button and it freezes on bootup at Lenovo screen.
I can hook it to my computer as a USB drive but is sees nothing. I am at a loss.
Any ideas how to fix this. Any help would be appreciated.
PS I cannot even get to the settings menu to switch to dev mode ... I have Win XP as my operating system so if you give instructions to fix this thing keep that in mind.
jimmyh88 said:
I have a dead lenovo IdeaTab. It powers up and will hang at the Lenovo screen. The only way out of this is to use the reset button. I have tried to do a wipe/factory reset with no luck. When I tell it to reset to factory default, it hangs up with the android picture on the screen just stays there. Again with the reset button and it freezes on bootup at Lenovo screen.
I can hook it to my computer as a USB drive but is sees nothing. I am at a loss.
Any ideas how to fix this. Any help would be appreciated.
PS I cannot even get to the settings menu to switch to dev mode ... I have Win XP as my operating system so if you give instructions to fix this thing keep that in mind.
Click to expand...
Click to collapse
Have you tried getting into recovery?
If not Hold the powerbutton + one of the volume buttons. (or both it depends)
E-13 said:
Have you tried getting into recovery?
If not Hold the powerbutton + one of the volume buttons. (or both it depends)
Click to expand...
Click to collapse
Yes It hangs after recovery as well. Data wipe completes then I reboot ... goes straight back to Lenovo screen and stays there.
Up volume + power is recovery mode
Down Volume + power is test mode.
Wifi fails... everything else seems to test good.
jimmyh88 said:
Yes It hangs after recovery as well. Data wipe completes then I reboot ... goes straight back to Lenovo screen and stays there.
Up volume + power is recovery mode
Down Volume + power is test mode.
Wifi fails... everything else seems to test good.
Click to expand...
Click to collapse
Have you tried connecting the pc while in Recovery mode?
If you have go to Device Manager on your pc and look if it sees the device. If it does it will probarly see it as "unknown device"
If it sees it as Unkown Device,
Look for the Lenovo drivers for your phone. Install them.
Reconnect your device while in recovery. This time your tab should be recognised.
If it has install ADB. I recommend this: Minimal ADB&Fastboot
Launch this and type ADB devices. If it recognises your device. Well thats great. If not and your pc has recognised it. Then try messing in recovery. I had this same problem once with a old tablet which was from polaroid and didnt/barely gave any drivers at all.
E-13 said:
Have you tried connecting the pc while in Recovery mode?
If you have go to Device Manager on your pc and look if it sees the device. If it does it will probarly see it as "unknown device"
If it sees it as Unkown Device,
Look for the Lenovo drivers for your phone. Install them.
Reconnect your device while in recovery. This time your tab should be recognised.
If it has install ADB. I recommend this: Minimal ADB&Fastboot
Launch this and type ADB devices. If it recognises your device. Well thats great. If not and your pc has recognised it. Then try messing in recovery. I had this same problem once with a old tablet which was from polaroid and didnt/barely gave any drivers at all.
Click to expand...
Click to collapse
Ok I have found the device and can read from it with ADB.exe I have downloaded source code in rar file and can extract. There is one primary file called Kernel with multiple files under that. How do I transfer that to the tablet or is there another method through ADB to restore to factory default.
Thanks so much for the help.
jimmyh88 said:
Ok I have found the device and can read from it with ADB.exe I have downloaded source code in rar file and can extract. There is one primary file called Kernel with multiple files under that. How do I transfer that to the tablet or is there another method through ADB to restore to factory default.
Thanks so much for the help.
Click to expand...
Click to collapse
Not so fast
If you flash only the kernel you shall achieve nothing.(at least not in this case because you have another problem)
But before I continue. How did this happen?
And are you maybe using a costum or the standard recovery?
E-13 said:
Not so fast
If you flash only the kernel you shall achieve nothing.(at least not in this case because you have another problem)
But before I continue. How did this happen?
And are you maybe using a costum or the standard recovery?
Click to expand...
Click to collapse
As it was described to me by my daughter ... A new game was downloaded and while playing that game or another game, it froze and would only reboot to the Lenovo screen and never get any further.
I have the download from lenovo. Apparently it is the full package but I am not sure exactly what to do with it.
jimmyh88 said:
I have a dead lenovo IdeaTab. It powers up and will hang at the Lenovo screen. The only way out of this is to use the reset button. I have tried to do a wipe/factory reset with no luck. When I tell it to reset to factory default, it hangs up with the android picture on the screen just stays there. Again with the reset button and it freezes on bootup at Lenovo screen.
I can hook it to my computer as a USB drive but is sees nothing. I am at a loss.
Any ideas how to fix this. Any help would be appreciated.
PS I cannot even get to the settings menu to switch to dev mode ... I have Win XP as my operating system so if you give instructions to fix this thing keep that in mind.
Click to expand...
Click to collapse
Flash the firmware, the instructions in here: http://forum.xda-developers.com/showthread.php?t=2772760
I had been looking for this in order to fix an irulu expro x1 tablet with much difficulty
after weeks of searching and trial and error i figured it out with some help from the net piecing info together
so now with my success i share with you:
1. shutdown tablet
2. power + vol ^ (hold till green android man)
3. power + vol ^ (might need to tap both multiple times, but be patient) enter recovery mode
4. scroll thru recovery menu, factory rest, clear cache, restart
5. now on pc extract zip file open sp flash tools folder, run application as administrator
6. load scatter file of X1048 x1049 xxxxx...
7. select all including preloader, instead of download only choose format all and download
8. hit download, make sure you power off tablet, then connect usb to pc
should show the red progress line, and after a few seconds begin flashing the tablet, allow it to do its thing till
green ok dialog button appears, power on and voila!!!
mod edit: pay per click link removed.
Is that file you posted a newer updated rom?(4.4.2 or better ?) And what exactly does this flash "fix" ?
xL2e said:
I had been looking for this in order to fix an irulu expro x1 tablet with much difficulty
after weeks of searching and trial and error i figured it out with some help from the net piecing info together
so now with my success i share with you:
1. shutdown tablet
2. power + vol ^ (hold till green android man)
3. power + vol ^ (might need to tap both multiple times, but be patient) enter recovery mode
4. scroll thru recovery menu, factory rest, clear cache, restart
5. now on pc extract zip file open sp flash tools folder, run application as administrator
6. load scatter file of X1048 x1049 xxxxx...
7. select all including preloader, instead of download only choose format all and download
8. hit download, make sure you power off tablet, then connect usb to pc
should show the red progress line, and after a few seconds begin flashing the tablet, allow it to do its thing till
green ok dialog button appears, power on and voila!!!
Click to expand...
Click to collapse
ssjgotengt said:
Is that file you posted a newer updated rom?(4.4.2 or better ?) And what exactly does this flash "fix" ?
Click to expand...
Click to collapse
sorry for the late responce, but the fix was for a virus, a very toublesome one by-the-way, that seemed to stay on the device even from a system reset, or from the recovery even after a wipe of cache/data/dalvic and what not... had been looking for the rom and couldnt find anywhere, had contacted the irulu site and we had multiple back and forth thru email... it was only however thru trial and error i found the correct rom which i posted for benefit of anyone who needs it.
also the fix was for an in-law but i believe it it was 4.4.2...
expro x1
Can you tell me tge serial number of your device? I've been looking for the firmware but none are working
expro x1
xL2e said:
sorry for the late responce, but the fix was for a virus, a very toublesome one by-the-way, that seemed to stay on the device even from a system reset, or from the recovery even after a wipe of cache/data/dalvic and what not... had been looking for the rom and couldnt find anywhere, had contacted the irulu site and we had multiple back and forth thru email... it was only however thru trial and error i found the correct rom which i posted for benefit of anyone who needs it.
also the fix was for an in-law but i believe it it was 4.4.2...
Click to expand...
Click to collapse
can you update the link?
kahrloz said:
Can you tell me tge serial number of your device? I've been looking for the firmware but none are working
Click to expand...
Click to collapse
Please don't ask for serial numbers here. :good:
My Irulu tablet does not have volume buttons.
Only power & esc buttons.
How do I get it into recovery mode then?
Hi all, I downloaded the firmware from Irulu for the 8-inch Expand x1s version, but I can not install it in Sideload ADB mode can you help me?
***fixed for irulu Inc through Android reset method
While it is on hold the power button and hit power off and when prompted to have it boot in quick mode hit yes. Turn on and it power button. And when asked to power off or reboot hold the power off link and agree to have safe mode activated. (Even if it was already activated the process of the irulu is quite similar to down syndrome so must repeat for the second time). Once off hold power and volume up till it brings recovery mode into display.
Tinman_Haus said:
While it is on hold the power button and hit power off and when prompted to have it boot in quick mode hit yes. Turn on and it power button. And when asked to power off or reboot hold the power off link and agree to have safe mode activated. (Even if it was already activated the process of the irulu is quite similar to down syndrome so must repeat for the second time). Once off hold power and volume up till it brings recovery mode into display.
Click to expand...
Click to collapse
Good morning, is the advice for my problem? because with the translation I can not understand. Thanks anyway
---------- Post added at 05:57 AM ---------- Previous post was at 05:44 AM ----------
xL2e said:
I had been looking for this in order to fix an irulu expro x1 tablet with much difficulty
after weeks of searching and trial and error i figured it out with some help from the net piecing info together
so now with my success i share with you:
1. shutdown tablet
2. power + vol ^ (hold till green android man)
3. power + vol ^ (might need to tap both multiple times, but be patient) enter recovery mode
4. scroll thru recovery menu, factory rest, clear cache, restart
5. now on pc extract zip file open sp flash tools folder, run application as administrator
6. load scatter file of X1048 x1049 xxxxx...
7. select all including preloader, instead of download only choose format all and download
8. hit download, make sure you power off tablet, then connect usb to pc
should show the red progress line, and after a few seconds begin flashing the tablet, allow it to do its thing till
green ok dialog button appears, power on and voila!!!
mod edit: pay per click link removed.
Click to expand...
Click to collapse
Hello, my irulu is locked in a recovery mode for a year and can not install the original firmware. Can you help me with any rom so I can reactivate my tablet? . Thank you.
Jascha2016 said:
Good morning, is the advice for my problem? because with the translation I can not understand. Thanks anyway
---------- Post added at 05:57 AM ---------- Previous post was at 05:44 AM ----------
Hello, my irulu is locked in a recovery mode for a year and can not install the original firmware. Can you help me with any rom so I can reactivate my tablet? . Thank you.
Click to expand...
Click to collapse
Hey I couldn't find this firmware after you asked but I have since found it in an old hard drive so I am sharing it with you, hope it helps with restoring your tablet...
https://drive.google.com/file/d/17mpGEyaKRODxHkoBDen5YxxktFhvD5Mp/view?usp=drivesdk
Sent from my SM-G935F using Tapatalk
kahrloz said:
can you update the link?
Click to expand...
Click to collapse
https://drive.google.com/file/d/17mpGEyaKRODxHkoBDen5YxxktFhvD5Mp/view?usp=drivesdk
Sent from my SM-G935F using Tapatalk
xL2e said:
I had been looking for this in order to fix an irulu expro x1 tablet with much difficulty
after weeks of searching and trial and error i figured it out with some help from the net piecing info together
so now with my success i share with you:
1. shutdown tablet
2. power + vol ^ (hold till green android man)
3. power + vol ^ (might need to tap both multiple times, but be patient) enter recovery mode
4. scroll thru recovery menu, factory rest, clear cache, restart
5. now on pc extract zip file open sp flash tools folder, run application as administrator
6. load scatter file of X1048 x1049 xxxxx...
7. select all including preloader, instead of download only choose format all and download
8. hit download, make sure you power off tablet, then connect usb to pc
should show the red progress line, and after a few seconds begin flashing the tablet, allow it to do its thing till
green ok dialog button appears, power on and voila!!!
mod edit: pay per click link removed.
Click to expand...
Click to collapse
https://drive.google.com/file/d/17mpGEyaKRODxHkoBDen5YxxktFhvD5Mp/view?usp=drivesdk
Sent from my SM-G935F using Tapatalk
irulu tablet expro x1 x9 pro firmware
am looking the irulu tablet expro x1 x9 pro firmware