Hello, long time reader, first time poster. I know about rooting, and installing roms and all that good stuff (had a galaxy s2 but odin bricked it). So I'm new to the sensation, and it's quite different from my previous device. My problem is that when I install a custom rom, the phone will boot and all about after about 30 seconds will freeze and restart.
Okay so these are the steps that I followed:
-Used the KGS Utility and chose "s-off"
-Followed all the prompts everything worked out fine.
-Following that I used it to install a custom recovery.
-Followed the prompts everything worked fine.
-Then I used Revolutionary CWM to flash SuperUser.
-App was there on reboot.
-Then I downloaded the AOKP "Initiate Your Swagger"[4.1.2] Rom
-Put it on my SD card and flashed it (after wiping and backing up)
-When the phone boots the setup wizard starts.
-I follow the prompt and when it gets to "Just a sec" the phone freezes then restarts.
Don't know what the problem is here.
I get the same problem when trying to flash CM10. The phone will boot, but then after 20-30 seconds will reboot.
kojimin said:
Hello, long time reader, first time poster. I know about rooting, and installing roms and all that good stuff (had a galaxy s2 but odin bricked it). So I'm new to the sensation, and it's quite different from my previous device. My problem is that when I install a custom rom, the phone will boot and all about after about 30 seconds will freeze and restart. I also noticed that there is no signal in custom roms either. Don't know what I'm doing wrong here. I used an all in one tool to do s-off, and install a custom recovery. Then I rooted it. Then I started trying to install custom roms but they don't seem to work. What am I doing wrong?
Click to expand...
Click to collapse
Be VERY specific and give a step by step detail of what you are doing to install. Give WAY more detail than you have. And put the detail in a list, not a giant paragraph.
Then we'll look at it and see what's missing.
Skipjacks said:
Be VERY specific and give a step by step detail of what you are doing to install. Give WAY more detail than you have. And put the detail in a list, not a giant paragraph.
Then we'll look at it and see what's missing.
Click to expand...
Click to collapse
Sorry about that. Edited my first post. I hope that is enough.
When you say it boots for 20 seconds, what exaclty for you mean.
Does it just replay the boot animation over and over? Or does it actually bring you to a home screen with the status bar and everything for 20 seconds before the reboot? That's a very important difference in diagnosing this one.
Also try installing 4EXT recovery. CWM has been known to cause weirdness with AOSP roms. Plus you may have an older version of CWM thatcan't properly install the newer roms. If you used a .zip in bootloader to flash CWM yuou probably had an older version. I have a special place in my heart for CWM too, but 4EXT is just so much better for the Sensation. (Different recoveries ar ebetter or worse on different devices.)
If you properly installed superuser on your stock rom that you have a nandroid backup for, installing 4EXT is super easy. Just restore the nandroid, which should boot up without problems, download the 4EXT app from the play store, and use the app to install teh latest version of the recovery. No need for ADB or flashing in bootloader. Then try a full wipe and fresh install of AOKP from 4EXT.
Skipjacks said:
When you say it boots for 20 seconds, what exaclty for you mean.
Does it just replay the boot animation over and over? Or does it actually bring you to a home screen with the status bar and everything for 20 seconds before the reboot? That's a very important difference in diagnosing this one.
Also try installing 4EXT recovery. CWM has been known to cause weirdness with AOSP roms. Plus you may have an older version of CWM thatcan't properly install the newer roms. If you used a .zip in bootloader to flash CWM yuou probably had an older version. I have a special place in my heart for CWM too, but 4EXT is just so much better for the Sensation. (Different recoveries ar ebetter or worse on different devices.)
If you properly installed superuser on your stock rom that you have a nandroid backup for, installing 4EXT is super easy. Just restore the nandroid, which should boot up without problems, download the 4EXT app from the play store, and use the app to install teh latest version of the recovery. No need for ADB or flashing in bootloader. Then try a full wipe and fresh install of AOKP from 4EXT.
Click to expand...
Click to collapse
It boots up to the homescreen (with no signal) then it reboots.
I will try 4EXT and post my results. Thanks for your help thus far!
EDIT: Tryed installing 4EXT now when I try to boot into recovery it shows the HTC spash screen, then it reboots back the homescreen. So I think my recovery is gone.
EDIT 2: So I got the 4EXT recovery installed. But the ROMs are giving me the same issues (no change). I also noticed as before, when the custom roms boot there isn't any cellular signal.
kojimin said:
It boots up to the homescreen (with no signal) then it reboots.
I will try 4EXT and post my results. Thanks for your help thus far!
EDIT: Tryed installing 4EXT now when I try to boot into recovery it shows the HTC spash screen, then it reboots back the homescreen. So I think my recovery is gone.
EDIT 2: So I got the 4EXT recovery installed. But the ROMs are giving me the same issues (no change). I also noticed as before, when the custom roms boot there isn't any cellular signal.
Click to expand...
Click to collapse
Update the firmware.. You are on gingerbread firmware (revolutionary soff worked for you means you are on GB) and it won't work on ics/jb roms
Check the firmware thread by kohr-ah in sensation development section and flash universal 3.33 firmware
It will solve your rom problems
Sent from my HTC Sensation 4G using xda premium
ganeshp said:
Update the firmware.. You are on gingerbread firmware (revolutionary soff worked for you means you are on GB) and it won't work on ics/jb roms
Check the firmware thread by kohr-ah in sensation development section and flash universal 3.33 firmware
It will solve your rom problems
Sent from my HTC Sensation 4G using xda premium
Click to expand...
Click to collapse
it was the firmware! I just updated to 3.33, and 4.1.2 "Initiate your swagger" booted up completely. Thanks for your help :good:
Awesome reply mate :
Sent from my HTC Sensation XE with Beats Audio using xda premium
Related
I've a huge problem
I've a Sensation 4g I was on stock ics and i followed the guide to get root, htc dev unlock e CWM... (still s.off) after that I installed 4ext and ARHD 6.7.0.. and everything was fine..
Then i tried to install cyanogenmod 9 which requires CWM again.. so i've installed rom manager and installed cwm through it..
I was stuck on the bootloader image, so i tried to flash back my recovery which of course isn't working because i have CWM now and so i tried to flash back ARHD but it will get untill the beginning when it says "optimizing app" and it restarts and again and again....
Anyway i can fix this problem?? I tried to flash another rom "energy ics" which don't require 4ext.. but i got the same results!!! what should i do?! did i brick my phone?
anyway to install 4ext without having a rom working?
andre_07 said:
I've a huge problem
I've a Sensation 4g I was on stock ics and i followed the guide to get root, htc dev unlock e CWM... (still s.off) after that I installed 4ext and ARHD 6.7.0.. and everything was fine..
Then i tried to install cyanogenmod 9 which requires CWM again.. so i've installed rom manager and installed cwm through it..
I was stuck on the bootloader image, so i tried to flash back my recovery which of course isn't working because i have CWM now and so i tried to flash back ARHD but it will get untill the beginning when it says "optimizing app" and it restarts and again and again....
Anyway i can fix this problem?? I tried to flash another rom "energy ics" which don't require 4ext.. but i got the same results!!! what should i do?! did i brick my phone?
anyway to install 4ext without having a rom working?
Click to expand...
Click to collapse
yes flash recovery using this guide
FLASHING ROMS WITH SON
just follow step 2 from above guide if you are SOFF
if SON follow step 2 and 3
Did you install the correct firmware? ICS based Roms is usually 3.32, firmware ?
Sent from my HTC Sensation 4G using xda premium
realsis said:
Did you install the correct firmware? ICS based Roms is usually 3.32, firmware ?
Sent from my HTC Sensation 4G using xda premium
Click to expand...
Click to collapse
Let's say right now I've a big confusion in my head.. Beore I had ICS working.. i never even tried to downgrade so i should have the correct firmware right?
the last time i check i had 1.32 (and don't remember but it was the last one installed with the tmous OTA)...
Maybe when i did my first format of the sd should i've installed something before the rom?
can anyone giving me the exact path of the cwm backup?
andre_07 said:
can anyone giving me the exact path of the cwm backup?
Click to expand...
Click to collapse
andre read my previous post to flash 4EXT this doesn't require a working rom
also in normal the backups are present on SDCRAD
ie /sdcard/clockworkmod/backup
so once you format the sdcard you will lose the backups
andre_07 said:
Let's say right now I've a big confusion in my head.. Beore I had ICS working.. i never even tried to downgrade so i should have the correct firmware right?
the last time i check i had 1.32 (and don't remember but it was the last one installed with the tmous OTA)...
Maybe when i did my first format of the sd should i've installed something before the rom?
Click to expand...
Click to collapse
If I read this correct you have the official stock firmware that was with the T-Mobile OTA ICS update. This means your bootloader is locked even though you are S-off. You need to flash a engineered Hboot to solve this. Go to this thread to get a firmware package with this. Go to the "User-Friendly Firmware" thread by Kohr-Ah, or you can also use the firmware from GROG88's thread here.
To the Guru of this forum. After my last rom flashing my device is keeping booting into recovery :crying:. Is it briked ? If so my only hope is the unbricking project ? Thanks in advance.
What recovery are you running?
Can you use the power menu within recovery to boot into bootloader?
Also, please provide as much pertinent info as possible, ie: rom you flashed, firmware, s-off or s-on, locked or unlocked. With your description it's basically like saying, "my car makes a noise all the time. what is causing it?".
Its not bricked.If u can enter recovery
Sent from my HTC sensation
Sorry you are right:
What recovery are you running? 4Ext
Can you use the power menu within recovery to boot into bootloader? yes
The device is HTC unlocked with S-On.
Rom JBMIUI v4.1 2.8.31 R2.
HBOOT 1.27.0000
firmware 3.33.401.6
I've format everything but SD. Restored the most recent back up done today before flashing. Once it reboots HTC logo comes up once, black screen, HTC logo, 4Ext is coming up saying that smartflash it is set to update the boot partition on next system start asking if this should be removed.
I've downloaded and installed again PG58IMG *different files using bootloader
I've founded a 3.33.401.6-Unsecured-Boot.img,+Root+Busybox zip file that can be installed via recovery but it did not help.
At this point I need a bit of help to look into the right direction and I'm not sure that Unbrick_Pyramid is the right way.
Thanks again.
Try turning off smartflash and flash a 3.33 stock rom to see if it will boot.
What was your last working setup, and what were you trying to install?
Sent from my HTC Sensation 4G using Tapatalk 2
Hi. Manage to flash a stock 3.33.
It stopped to reboot straight into recovery.
Sits now on HTC logo now for about 10 mins. I plan to let him run for 1 hr and see what happens.
Was thinking to install CWM on the basis that could be a 4ext recovery issue, toughs?
GROGG88 said:
Try turning off smartflash and flash a 3.33 stock rom to see if it will boot.
What was your last working setup, and what were you trying to install?
Sent from my HTC Sensation 4G using Tapatalk 2
Click to expand...
Click to collapse
If you can install clockworkmod that may help.
Tge device isnt getting the message that it has already booted into recovery once. So something may be jacked up with 4ext.
Clockwork may bypass all that when it doesnt know what to do with that signal to run smartflash.
Worst case scenario...put a full pm58img containing a rom and recovery on the sf card and flash that through bootloader.
You should still be able to get to bootloader as the device looks for that option first.
Sent from my HTC Sensation using xda app-developers app
Hallo. Ok installed CWM. Can please direct me to a full pm58img as you mentioned ? Thx.
Skipjacks said:
If you can install clockworkmod that may help.
Tge device isnt getting the message that it has already booted into recovery once. So something may be jacked up with 4ext.
Clockwork may bypass all that when it doesnt know what to do with that signal to run smartflash.
Worst case scenario...put a full pm58img containing a rom and recovery on the sf card and flash that through bootloader.
You should still be able to get to bootloader as the device looks for that option first.
Sent from my HTC Sensation using xda app-developers app
Click to expand...
Click to collapse
DiscreteTask said:
Hallo. Ok installed CWM. Can please direct me to a full pm58img as you mentioned ? Thx.
Click to expand...
Click to collapse
And did that help? Are you able to get into recovery without errors now? If so you should be able to flash a fresh version of any ROM.
Try that first. Get any ROM. Flash it. See if it boots.
If you have successfully replaced 4EXT I will bet a fresh flash of a ROM will now boot.
Also worth a shot is replacing or upgrading the firmware, as that could be what's sending the phone into recovery on each boot (though this is less likely that 4EXT just being broken)
Flash a firmware PM58IMG like 3.32 or 3.33 and see if that helps.
But for starters, put a fresh ROM on the SD card and flash it with CWM. (BE SURE IT'S A ROM THAT DOESN'T REQUIRE 4EXT!!)
Once you've got it all fixed you can switch back to 4EXT. I have a feeling it was just the copy you were running that got botched. The software itself is solid and stable. A new copy shoudl work fine now.
CWM v5.0.2.0 was installed fine.
3.33 firmware installed once again.
Using this I've installed ROM that I already did in the past w/o luck, they all sit on the HTC logo. Is like the initial boot sequence is broken. Is boot.img part of the firmware or ROM ?
Trying to download some additional ones.
Thanks,
Skipjacks said:
And did that help? Are you able to get into recovery without errors now? If so you should be able to flash a fresh
version of any ROM.
Try that first. Get any ROM. Flash it. See if it boots.
If you have successfully replaced 4EXT I will bet a fresh flash of a ROM will now boot.
Also worth a shot is replacing or upgrading the firmware, as that could be what's sending the phone into recovery on each boot (though this is less likely that 4EXT just being broken)
Flash a firmware PM58IMG like 3.32 or 3.33 and see if that helps.
But for starters, put a fresh ROM on the SD card and flash it with CWM. (BE SURE IT'S A ROM THAT DOESN'T REQUIRE 4EXT!!)
Once you've got it all fixed you can switch back to 4EXT. I have a feeling it was just the copy you were running that got botched. The software itself is solid and stable. A new copy shoudl work fine now.
Click to expand...
Click to collapse
DiscreteTask said:
CWM v5.0.2.0 was installed fine.
3.33 firmware installed once again.
Using this I've installed ROM that I already did in the past w/o luck, they all sit on the HTC logo. Is like the initial boot sequence is broken. Is boot.img part of the firmware or ROM ?
Trying to download some additional ones.
Thanks,
Click to expand...
Click to collapse
The more details you give, the better the answers will be. Don't consider any detail too small.
What do you mean you installed ROM's that you had done in the past? Do you mean you are trying to restore a backup made with 4EXT?
That won't work. You need to flash a fresh version of the ROM after wiping.
Also, CWM won't install some ROM's that you may have used in the past. What ROM are you trying to install?
The HTC logo that first pops up when you hit the power button is part of the firmware.
Make sure you do a full wipe of everything but the SD card from within CWM. Get whatever's causing the problem off that way. Then flash a fresh install of a ROM from scratch.
Hi.
I did not use any backup only fresh ROMs: ARHD, Elegantia, but also stock ROMs I could find.
I've tried also some PG58IMG with ROM included.
Cheers.
Skipjacks said:
The more details you give, the better the answers will be. Don't consider any detail too small.
What do you mean you installed ROM's that you had done in the past? Do you mean you are trying to restore a backup made with 4EXT?
That won't work. You need to flash a fresh version of the ROM after wiping.
Also, CWM won't install some ROM's that you may have used in the past. What ROM are you trying to install?
The HTC logo that first pops up when you hit the power button is part of the firmware.
Make sure you do a full wipe of everything but the SD card from within CWM. Get whatever's causing the problem off that way. Then flash a fresh install of a ROM from scratch.
Click to expand...
Click to collapse
Arhd and elegencia wont work with cwm. So there is your isdue. Try cm9 or 10 to see if you can boot one of those.
Sent from my HTC Sensation using xda app-developers app
Hallo, after trying all option the following did work for me:
- re-lock bootloader via fastboot oem lock
- apply stock ROM founded in this list http://forum.xda-developers.com/showthread.php?t=1074559
- rebooted fine
I guess that HTC RUU had some superpower and erase and installed whatever file(s) were corrupted.
Now I'm on stock 3.6 - fw 3.33.401.106 - radio 11.76A.3504.00UU_11.24A.3504.31_M
HBOOT 1.29 - S-ON - Relocked.
Standard Recovery.
Now I'm reading how to return my device to S-OFF w/o damaging it again.
Many thanks to skipjacks & groog88 :good:
Skipjacks said:
Arhd and elegencia wont work with cwm. So there is your isdue. Try cm9 or 10 to see if you can boot one of those.
Sent from my HTC Sensation using xda app-developers app
Click to expand...
Click to collapse
Hi all,
I'm trying to help a friend update his Sensation to bruce2728's CM10 beta. I started from scratch on an updated-to-4.0.3 device with this phone and have done a fair amount of research. So far, I have done the following:
1.) Unlocked my boot loader via HTCDev
2.) flashed a custom recovery via fastboot - it's CWM-based 6.0.0.0. I can boot into recovery and back up the ROM and restore it
3.) Rooted with the CWM-flashable SuperSU 0.9.6 and verified root.
4.) used the JuopunutBear method to enable S-OFF. This is verified by booting to the boot loader, it says S-OFF and hboot version 1.27.1111
5.) Flashed a custom ROM
And #4 is where I run into problem.s I started with the CM10 beta mentioned above. It seems to install OK, and then I install G-apps, wipe data/cache, and reboot. I get to an htc logo and then it goes black and boots into recovery automatically. Tried wiping /system along with another wipe of data/cache and same result.
Thinking I had a bad download, I re-downloaded. Same results
Well maybe his Sensation is screwy, I wonder, so I grab the official CM9.1 release. Exact same procedure, exact same results.
So now I'm wondering, what can I do? Right now it's back to running the stock but rooted ROM. So it's not the end of the world. Just trying to figure out what I did wrong or what I can do to fix it. Should I get the official 5.0.2.0 or touch 5.8.0.9? I see both of those on the ClockworkMod ROM manager website, and I own ROM Manager Premium, so I can do all that if need be. Thanks in advance.
You might want to try 4ext recovery it is probably the most used recovery for the sensation. Then wipe every thing except sd . Then flash the ROM then gapps. But make sure you have a working nandroid first.
Sent from my HTC Sensation using xda app-developers app
I do have a working Nandroid. I'll check into 4EXT, as well. Thanks for the assist.
Will you think less of me if I pay $2.82 for the automated installer? :lol:
No, I'm not going that route, just wondering.
edit 10:01pm Central - that did it. Booted into bruce2728's CM10 beta. Sweet!
I am wondering if I made any major changes or done anything wrong.
1) Yesterday I attempted to "S-Off" my phone for the first time ever since purchase. When "revolutionary.io" asked me what Bootloader I was on, I connected the phone through USB and the revolutionary executable told me 1.18.0000. The first few tries failed because it just kept saying "Waiting for bootloader" but after messing with different HTC drivers and unplugging a bunch of times it finally took and went through S-off. Now when I boot into bootloader it says my verison is 1.17 S-off. Is it correct that I went backwards from 1.18 to 1.17?
2) I flashed a custom ROM but being a noob that I am I knew nothing about firmware so I was stuck in bootloop of Cyanogen JB. I flashed through RUU to stock ROM but it is not the same stock ROM that came with my phone out of the box, some of the settings are different it does have the same network though TMOUS; especially the personalize options some of them do not work (themes). Is it alright if I flashed to this ROM as opposed to the exact same one that my phone came with? If I update my firmware and flash Cyanogen again this ROM is basically gone anyways right? I am just concerned that by RUU flashing this stock ROM I changed the firmware or baseband or something important.
Thats all I'm wondering, hoping you can give me a Yes or a No and a brief explanation to each question, thanks so much
fashofasho said:
I am wondering if I made any major changes or done anything wrong.
1) Yesterday I attempted to "S-Off" my phone for the first time ever since purchase. When "revolutionary.io" asked me what Bootloader I was on, I connected the phone through USB and the revolutionary executable told me 1.18.0000. The first few tries failed because it just kept saying "Waiting for bootloader" but after messing with different HTC drivers and unplugging a bunch of times it finally took and went through S-off. Now when I boot into bootloader it says my verison is 1.17 S-off. Is it correct that I went backwards from 1.18 to 1.17?
2) I flashed a custom ROM but being a noob that I am I knew nothing about firmware so I was stuck in bootloop of Cyanogen JB. I flashed through RUU to stock ROM but it is not the same stock ROM that came with my phone out of the box, some of the settings are different it does have the same network though TMOUS; especially the personalize options some of them do not work (themes). Is it alright if I flashed to this ROM as opposed to the exact same one that my phone came with? If I update my firmware and flash Cyanogen again this ROM is basically gone anyways right? I am just concerned that by RUU flashing this stock ROM I changed the firmware or baseband or something important.
Thats all I'm wondering, hoping you can give me a Yes or a No and a brief explanation to each question, thanks so much
Click to expand...
Click to collapse
when you did S-OFF in order to install Cyanogen JB first you had to flash the latest fw version and then the rom
the rom you tried to install requires the latest fw version
now are you still s-off?
what is now your hboot version?
what is your fw version?
I am wondering if I made any major changes or done anything wrong.
1) Yesterday I attempted to "S-Off" my phone for the first time ever since purchase. When "revolutionary.io" asked me what Bootloader I was on, I connected the phone through USB and the revolutionary executable told me 1.18.0000. The first few tries failed because it just kept saying "Waiting for bootloader" but after messing with different HTC drivers and unplugging a bunch of times it finally took and went through S-off. Now when I boot into bootloader it says my verison is 1.17 S-off. Is it correct that I went backwards from 1.18 to 1.17?
2) I flashed a custom ROM but being a noob that I am I knew nothing about firmware so I was stuck in bootloop of Cyanogen JB. I flashed through RUU to stock ROM but it is not the same stock ROM that came with my phone out of the box, some of the settings are different it does have the same network though TMOUS; especially the personalize options some of them do not work (themes). Is it alright if I flashed to this ROM as opposed to the exact same one that my phone came with? If I update my firmware and flash Cyanogen again this ROM is basically gone anyways right? I am just concerned that by RUU flashing this stock ROM I changed the firmware or baseband or something important.
Thats all I'm wondering, hoping you can give me a Yes or a No and a brief explanation to each question, thanks so much
Click to expand...
Click to collapse
1) Normal. You're good. And you'll have HBoot 1.27 or 1.29 when you're all done.
2) Not normal. You missed a step. You need to upgrade the firmware to 3.32 (HBoot 1.27) or 3.33 (HBoot 1.29). Either will run CM10, which gives you better performance is for you to decide. The difference is mainly the radio for cell reception. If you're a T Mobile user try the 3.32 for T Mobile for starters. (Available in the radio/firmware thread. Do a search and you'll find it.)
Basicly what you did was flash an Android 4.x ROM on Android 2.3 firmware. That doesn't work. They are incompatible.
If you RUU'ed back to stock, you might have reverted back to S-On and lost your custom recovery, so check. If you have S-On now, you have to start over.
If you still have s-off and can still get into your recovery (Clockwork or 4EXT, I receomend 4EXT but CM10 will load from either), find that Firmware thread, download 3.32 for T Mobile. Follow the instructions in that thread on how to install new firmware. It's painfully simple...you just put the firmware file on teh SD card, reboot, and let it do it's thing. The firmware thread will be more specific, but that's about it. It takes 2 minutes. The phone will suddenly go black and power off for a second during the process. Don't panic. It's normal. AND DON'T TOUCH IT UNTIL IT TELLS YOU TO!!!!
Once you've done that, the stock ROM you have now will not boot. You will need to boot to recovery (Clockwork or 4EXT), do a full wipe, and flash CM10 again.
It should not boot.
This entire process (if you are still s-off and have your recovery working still) should take no more than 15 minutes. It sounds complicated but it's really not. I promise!
I just gave you a general overview. If you get stuck at any point come back and ask more specific questions about where you are stuck.
Skipjacks said:
1) Normal. You're good. And you'll have HBoot 1.27 or 1.29 when you're all done.
2) Not normal. You missed a step. You need to upgrade the firmware to 3.32 (HBoot 1.27) or 3.33 (HBoot 1.29). Either will run CM10, which gives you better performance is for you to decide. The difference is mainly the radio for cell reception. If you're a T Mobile user try the 3.32 for T Mobile for starters. (Available in the radio/firmware thread. Do a search and you'll find it.)
Basicly what you did was flash an Android 4.x ROM on Android 2.3 firmware. That doesn't work. They are incompatible.
If you RUU'ed back to stock, you might have reverted back to S-On and lost your custom recovery, so check. If you have S-On now, you have to start over.
If you still have s-off and can still get into your recovery (Clockwork or 4EXT, I receomend 4EXT but CM10 will load from either), find that Firmware thread, download 3.32 for T Mobile. Follow the instructions in that thread on how to install new firmware. It's painfully simple...you just put the firmware file on teh SD card, reboot, and let it do it's thing. The firmware thread will be more specific, but that's about it. It takes 2 minutes. The phone will suddenly go black and power off for a second during the process. Don't panic. It's normal. AND DON'T TOUCH IT UNTIL IT TELLS YOU TO!!!!
Once you've done that, the stock ROM you have now will not boot. You will need to boot to recovery (Clockwork or 4EXT), do a full wipe, and flash CM10 again.
It should not boot.
This entire process (if you are still s-off and have your recovery working still) should take no more than 15 minutes. It sounds complicated but it's really not. I promise!
I just gave you a general overview. If you get stuck at any point come back and ask more specific questions about where you are stuck.
Click to expand...
Click to collapse
i got confused
.i think your answer is going for fashofasho
Skipjacks said:
1) Normal. You're good. And you'll have HBoot 1.27 or 1.29 when you're all done.
2) Not normal. You missed a step. You need to upgrade the firmware to 3.32 (HBoot 1.27) or 3.33 (HBoot 1.29). Either will run CM10, which gives you better performance is for you to decide. The difference is mainly the radio for cell reception. If you're a T Mobile user try the 3.32 for T Mobile for starters. (Available in the radio/firmware thread. Do a search and you'll find it.)
Basicly what you did was flash an Android 4.x ROM on Android 2.3 firmware. That doesn't work. They are incompatible.
If you RUU'ed back to stock, you might have reverted back to S-On and lost your custom recovery, so check. If you have S-On now, you have to start over.
If you still have s-off and can still get into your recovery (Clockwork or 4EXT, I receomend 4EXT but CM10 will load from either), find that Firmware thread, download 3.32 for T Mobile. Follow the instructions in that thread on how to install new firmware. It's painfully simple...you just put the firmware file on teh SD card, reboot, and let it do it's thing. The firmware thread will be more specific, but that's about it. It takes 2 minutes. The phone will suddenly go black and power off for a second during the process. Don't panic. It's normal. AND DON'T TOUCH IT UNTIL IT TELLS YOU TO!!!!
Once you've done that, the stock ROM you have now will not boot. You will need to boot to recovery (Clockwork or 4EXT), do a full wipe, and flash CM10 again.
It should not boot.
This entire process (if you are still s-off and have your recovery working still) should take no more than 15 minutes. It sounds complicated but it's really not. I promise!
I just gave you a general overview. If you get stuck at any point come back and ask more specific questions about where you are stuck.
Click to expand...
Click to collapse
Thanks for the reply. Okay so here is where I am currently at. I haven't done anything since I reflashed stock ROM throguh RUU after the fail cyanogen flash. On this stock ROM whenever I load into bootloader it still says s-off 1.17 but I did lose my clockworkmod. So according to your instructions I should either clockworkmod again or 4ext now, that's okay right? If so, going to flash firmware then cyanogen!! Or is there a problem that I have s-off but not recovery.
P.s. there is no point in running revolutionary and have it s-off again when I already have it right, just thought it might be necessary to make things fresh
If you have a bootable phone right now this is easy as you may not need adb or fast boot or anything.
First off you will need to install 4ext. Get the app from the Play Store. Then run it and let it install its recovery module. (You may need to be rooted to do thus, which your stock rom is not. Im not sure if you can flash the recovery without root or not because Ive never tried without root. If so, then you will have to install Superuser via fastboot I think. You any guide for rooting to get instructions on this. Its easy.)
You may also find a way to install 4ext recovery via flashing from bootloader, but you will have to search for that. You MAY even be able to install it with the firmware upgrade. You will have to see if that is an available option.
Get your firmware from this thread...
forum.xda-developers.com/showthread.php?t=1459767
Follow the instructions to update. Once you have 3.3x firmware and 4ext simply boot to recovery, do a full wipe, and flash cm10 (make sure cm10 is on your sd card. You can download it from your currently working gingerbread rom so you have it available)
You have like 15-20 minutes worth of work to do, so its not a monumental obstacle to overcome. It just seems like alot
Sent from my HTC Sensation using xda app-developers app
Skipjacks said:
If you have a bootable phone right now this is easy as you may not need adb or fast boot or anything.
First off you will need to install 4ext. Get the app from the Play Store. Then run it and let it install its recovery module. (You may need to be rooted to do thus, which your stock rom is not. Im not sure if you can flash the recovery without root or not because Ive never tried without root. If so, then you will have to install Superuser via fastboot I think. You any guide for rooting to get instructions on this. Its easy.)
You may also find a way to install 4ext recovery via flashing from bootloader, but you will have to search for that. You MAY even be able to install it with the firmware upgrade. You will have to see if that is an available option.
Get your firmware from this thread...
forum.xda-developers.com/showthread.php?t=1459767
Follow the instructions to update. Once you have 3.3x firmware and 4ext simply boot to recovery, do a full wipe, and flash cm10 (make sure cm10 is on your sd card. You can download it from your currently working gingerbread rom so you have it available)
You have like 15-20 minutes worth of work to do, so its not a monumental obstacle to overcome. It just seems like alot
Sent from my HTC Sensation using xda app-developers app
Click to expand...
Click to collapse
I am not rooted but am S-off. So my next step would be to root. I am suppose to have Clockworkmod to root AND 4EXT after right? Its not one or the other? I keep reading that people recommend 4ext is better than CWM but in order to root su-2.3.6.3-ef-signed.zip I need CWM first correct?
fashofasho said:
I am not rooted but am S-off. So my next step would be to root. I am suppose to have Clockworkmod to root AND 4EXT after right? Its not one or the other? I keep reading that people recommend 4ext is better than CWM but in order to root su-2.3.6.3-ef-signed.zip I need CWM first correct?
Click to expand...
Click to collapse
flash su-2.3.6.3-ef-signed.zip first and then install 4ext recovery
You're over engineering this. You don't need to root your current ROM first. That's an extra step since you're s-off.
If you are s-off it's really simple to get 4EXT recovery.
First, download this and put it on the root directory of your SD Card (meaning not in a folder, just on the SD Card. Do not rename it)
http://d-h.st/qnm
I got this download link from here...
http://forum.xda-developers.com/showthread.php?p=21989107
Click Thanks for Joaquinf in that thread. He made the 4EXT zip that's flashable through the bootloader.
That is 4EXT made into a zip file that's flashable via the bootloader, which you can do when you are S-off.
So put that file on the SD card, power the phone off, pull the battery out for a second and put it back in (this stops fastboot so you can get back to the bootloader). Then hold volume down and power at the same time. You have to hit both buttons at the same time. If it goes to the splash screen, pull the battery and try again.
When the bootloader loads up it will immediately find the PM58IMG.zip file. It will ask you if you want to install the update. Say yes by hitting volume up I think (it will tell you how to say yes)
Put the phone down and don't touch it until it tells you it's done. Should just take a second. But seriously don't touch it. Leave it alone.
If that works, you've just flashed 4EXT. You can check it by pulling the SD card out (so it doesn't try to flash the PM58IMG again) and rebooting to the bootloader and selecting 'recovery' from the menu. 4EXT should boot up.
This entire process so far shouldn't take more than 3 minutes total. It just sounds like a lot.
To see this detailed out by someone else in case you want to check what I'm saying, read steps 4 and 5 of the first post in this thread.
http://forum.xda-developers.com/showpost.php?p=21989063&postcount=1
Give the author 'thanks' again because he's awesome and deserves it.
Now you've got 4EXT installed. Great. You're 1/3rd of the way home.
Now you need to update your firmware. Delete the PM58IMG.zip file you used to flash 4EXT off the SD card (use a card reader or boot the phone up and delete it, whatever works. You can also use 4EXT as a card reader now too by choosing USB storage from inside 4EXT. It will give you access toteh SD card on your computer now)
Now get new Firmware from this thread.
http://forum.xda-developers.com/showthread.php?p=21711154#post21711154
try the 3.33 firmware universal. First download link in post 2 of the thread above.
CHECK THE MD5 SUM!!!! I'M NOT PLAYING AROUND HERE!!! You are worried about bricking your phone, this is where you can do it if the firmware .zip is bad.
Put that PM58IMG file on your SD and flash it in the bootloader the same way you flashed 4EXT recovery a minute ago. (If you're still in 4EXT recovery you can use it's power menu to reboot into bootloader easily.)
This will take a minute. The phone will shut off and go black in the middle of this process. Your heart will skip a beat. Relax. It'll come back on. Again, put the phone down and walk away while it does it's thing and don't touch it until it says it's done.
Delete the PM58IMG file from your SD card.
You are now 2/3 of the way there. Your phone WILL NOT boot up right now because your ROM is not compatible with your firmware. Relax. That's supposed to happen.
Now you can flash CM10. Make sure you have the CM10.zip file on your SD card nad GApps. (Bruce has Gapps in his downloads page). Delete the PM58IMG firmware file from your SD card (that's important)
Pull the battery again so you can get back into bootloader. Get into bootloader (power + volume down)
Select Recovery
4EXT should boot up.
Go to the Wipe menu. Wipe all partitions except SD card. (Old ROM is now gone)
Go back to the main menu.
Install from SD
Find the CM10.zip file you should have downloaded and put onto the SD card. Flash it.
This will take about 3 minutes. 4EXT will flash it and ask if you want to reboot. You do not yet. Not you need to flash Gapps the same way you flashed the ROM.
When that's done, now you can reboot. You shoudl see the CyanogenMod boot animation after the splash screen. Give it a few minutes to boot up this first time. Once it boots, set it up the way you like it. If you enjoy it, donate a few bucks to the developer, Bruce.
You don't have to root CM10. It's already rooted when you boot it up the first time.
Hey guys,
Having some problems with this ROM. I downloaded the ZIP, used Titanium backup to back it all up, and flashed the Rom with no problems at all...got through all the screens and whatnot, and upon launching for the first time it's stuck on the "Beats Audio" screen. Not really sure why or what happened. I'm coming from MIUI ROM and haven't had issues with flashing any other ROM before.
One thing I noticed is on the HD 7.3 first page there is a firmware update that you apparently need before you flash the ROM but all links are 404/not found.
Wondering if any of you pros can offer a hand?
-Cain
Cainsmoker said:
Hey guys,
Having some problems with this ROM. I downloaded the ZIP, used Titanium backup to back it all up, and flashed the Rom with no problems at all...got through all the screens and whatnot, and upon launching for the first time it's stuck on the "Beats Audio" screen. Not really sure why or what happened. I'm coming from MIUI ROM and haven't had issues with flashing any other ROM before.
One thing I noticed is on the HD 7.3 first page there is a firmware update that you apparently need before you flash the ROM but all links are 404/not found.
Wondering if any of you pros can offer a hand?
-Cain
Click to expand...
Click to collapse
post the output of this command
fastboot getvar all
don't show your imei and serial number
and what recovery do you have?
rzr86 said:
post the output of this command
fastboot getvar all
don't show your imei and serial number
and what recovery do you have?
Click to expand...
Click to collapse
In looking at my Hboot, it's old as sin....I'm using Revolutionary Hboot 1.17.1111 and Radio 10.14.9035.01_M
I run clockwork recovery mod v5.0.2.0 as well. This could be an issue causing the problem. I've been using the MIUI ROM for probably 2 years or so because I enjoyed it but I'm ready for a change. Apparently my phone doesn't agree. lol.
You want me to connect via USB and run the cmd prompt for the getvar command and let you know what it says?
Cainsmoker said:
In looking at my Hboot, it's old as sin....I'm using Revolutionary Hboot 1.17.1111 and Radio 10.14.9035.01_M
I run clockwork recovery mod v5.0.2.0 as well. This could be an issue causing the problem. I've been using the MIUI ROM for probably 2 years or so because I enjoyed it but I'm ready for a change. Apparently my phone doesn't agree. lol.
You want me to connect via USB and run the cmd prompt for the getvar command and let you know what it says?
Click to expand...
Click to collapse
there is no need to do it now
you gave me exactly what i need
you still have gb firmware that's why you can't boot ARHD 7.3(ics rom)
see this thread
http://forum.xda-developers.com/showthread.php?t=1459767
flash 3.33 universal
follow the instructions to the letter
and before flashing check md5 sums(important)
The speedy reply is much appreciated.
I'll go ahead and update the firmware and see where that lands me. I figured it could have been a problem from the get go but in the original thread for the HD 7.3 Rom the firmware link has been removed (likely since it was from 2011)
Thanks for the point in the right direction Rzr, and I'll let you know how it goes!
rzr86 said:
there is no need to do it now
you gave me exactly what i need
you still have gb firmware that's why you can't boot ARHD 7.3(ics rom)
see this thread
http://forum.xda-developers.com/showthread.php?t=1459767
flash 3.33 universal
follow the instructions to the letter
and before flashing check md5 sums(important)
Click to expand...
Click to collapse
Hmmm....the firmware update didn't work.
I can verify that I'm on the firmware 3.3, Hboot is 1.27.1100, Radio is 11.24A.3504.31_M.
Each time Hboot is run it asks if I want to start the update. If I select yes, I've got 9 on screen options that it runs through and tells me "Update complete. Press power to reboot" The only way to do anything at all is to take out the SD card so it does not try to load up the firmware zip
Pushing power reboots the phone on an endless boot loop. Regardless of what ROM is being used (I also downloaded cyanogenmod) I can not make it past the spash screen.
Could it be that I'm just flashing the ROM incorrectly? To my knowledge I've followed instructions for both and have backed up my phone and it's contents and done everything from a factory reset/wipe to wiping the dalvik cache, etc. I didn't have this many problems rooting my phone and putting on MIUI to begin with and have flashed ROMS before with no trouble....not really sure where I'm going wrong on this one.
Anyway, I'll await your reply.
Thank you!
-Cain
Update: awww frick. So now it looks like this will be more difficult....I hope you like a challenge. I can now no longer get into my phone. It appears that it's soft bricked. I have tried going to a clockwork mod recovery from my first MIUI in 2012, it goes through the entire process of factory resetting restoring the boot image, system and data information. It asks for a reboot which I do. It goes to the white HTC splash screen and the MIUI initializes and goes black immediately. There doesn't seem to be a way to get my phone connected to my computer to get into the SD card to troubleshoot from inside the phone. Hopefully one of you guys has the answer for me. Is there any way to get into it via bootloader usb?
Cainsmoker said:
Hmmm....the firmware update didn't work.
I can verify that I'm on the firmware 3.3, Hboot is 1.27.1100, Radio is 11.24A.3504.31_M.
Each time Hboot is run it asks if I want to start the update. If I select yes, I've got 9 on screen options that it runs through and tells me "Update complete. Press power to reboot" The only way to do anything at all is to take out the SD card so it does not try to load up the firmware zip
Pushing power reboots the phone on an endless boot loop. Regardless of what ROM is being used (I also downloaded cyanogenmod) I can not make it past the spash screen.
Could it be that I'm just flashing the ROM incorrectly? To my knowledge I've followed instructions for both and have backed up my phone and it's contents and done everything from a factory reset/wipe to wiping the dalvik cache, etc. I didn't have this many problems rooting my phone and putting on MIUI to begin with and have flashed ROMS before with no trouble....not really sure where I'm going wrong on this one.
Anyway, I'll await your reply.
Thank you!
-Cain
Update: awww frick. So now it looks like this will be more difficult....I hope you like a challenge. I can now no longer get into my phone. It appears that it's soft bricked. I have tried going to a clockwork mod recovery from my first MIUI in 2012, it goes through the entire process of factory resetting restoring the boot image, system and data information. It asks for a reboot which I do. It goes to the white HTC splash screen and the MIUI initializes and goes black immediately. There doesn't seem to be a way to get my phone connected to my computer to get into the SD card to troubleshoot from inside the phone. Hopefully one of you guys has the answer for me. Is there any way to get into it via bootloader usb?
Click to expand...
Click to collapse
remove the pg58img.zip from your sdcard so it won't scan and identify any pg58img.zip file
and don't restore your miui rom because probably is a gb one and now you have an ics firmware installed
just download an ics or jb rom
put it on your sdcard
full wipe from recovery
flash the rom
done
rzr86 said:
remove the pg58img.zip from your sdcard so it won't scan and identify any pg58img.zip file
and don't restore your miui rom because probably is a gb one and now you have an ics firmware installed
just download an ics or jb rom
put it on your sdcard
full wipe from recovery
flash the rom
done
Click to expand...
Click to collapse
With the phone being in a boot loop I can't get it detected by my computer to remove/add anything from the SD card. I do have the HD 7.3 ROM on and the Gapps that's required but it never makes it past the "beats audio" splash screen. I have no idea what's going on with it but will try any suggestions you've got up your sleeve.
Ahhhhh....I've gotten a fix for this!
I was unable to do anything because of the update zip which wanted me to update every time bootloader was initiated. By keeping my case off I removed my SD card to be able to boot in recovery and then put the SD card back in to load the HD 7.3 zip from the card. This seemed to take care of the problem.
Thanks for the help Rzr