Related
Hi all!
Im in a big pickle here and I cant get myself out at the moment.
First hand.. The info
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.13.0000
(bootloader) version-baseband: 0.17.31501S.10_2
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) product: vle
(bootloader) platform: HBOOT-8960
(bootloader) modelid: PJ4011000
(bootloader) cidnum: ROGER001
(bootloader) battery-status: good
(bootloader) battery-voltage: 3917mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-d92cc658
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.093s
Now i've been running cyanogenmod 10 stable since I started rooting etc...
And it's been amazing, but now since there has been a release candidate for 10.1, I was looking into updating it.
I ran into an issue where my boot-loader was not accepted , therefor i would run into an error on Clockwork mod stopping me from flashing 10.1
The bad thing was that I erased my previous installation without backing up the stock and CM10.
So now i'm left with no system. Though I can get into Fastboot and ADB via recovery.I
For some reason if I try to flash CM10 (The rom and the boot file) the cyanogenmod logo will continue spinning.
I tried to fiddle around with my RUU afterwards because I currently have S-On. But i later learned that i need superCID.
^(Which i learned that you need your phone on to alter it to the 8 "1"s) Which i cant do because i have no system.
I might have already altered some files guessing that my boot-loader is named "dirty-d92cc658" and im afraid that I messed up something internally.
So anyways. Im here with my Ville S4 plugged in on fastboot not knowing what to do.
Any Help would be amazing , thank you
Did you try a RUU for Rogers? Not sure if there is one but try to find a RUU that matches your cid
c19932 said:
Did you try a RUU for Rogers? Not sure if there is one but try to find a RUU that matches your cid
Click to expand...
Click to collapse
Do I need to have superCID to flash RUU's ?
Mozziliac said:
Do I need to have superCID to flash RUU's ?
Click to expand...
Click to collapse
If you have a RUU for your specific phone, no, you just need to lock the bootloader.
Have USB debugging turned on (unless running ruu when your phone is in fastboot usb mode)
If you can't find one for Rogers, then yes you have to be super cid to run another RUU.exe (after that change your cid back so an OTA update doesn't brick your phone)
If your phone is on Jellybean, you need to run a JB ruu, if it's Ice Cream Sandwich it won't run. Unless you are supercid I guess.
Khan.orak has a guide for OTA zips to return to stock that you might want.
http://forum.xda-developers.com/showthread.php?p=44365370
Ville / VilleC2 RUU, OTA and Stock Nandroid Collection
http://forum.xda-developers.com/showthread.php?t=2200930
tivofool said:
If you have a RUU for your specific phone, no, you just need to lock the bootloader.
Have USB debugging turned on (unless running ruu when your phone is in fastboot usb mode)
If you can't find one for Rogers, then yes you have to be super cid to run another RUU.exe (after that change your cid back so an OTA update doesn't brick your phone)
If your phone is on Jellybean, you need to run a JB ruu, if it's Ice Cream Sandwich it won't run. Unless you are supercid I guess.
Khan.orak has a guide for OTA zips to return to stock that you might want.
http://forum.xda-developers.com/showthread.php?p=44365370
Ville / VilleC2 RUU, OTA and Stock Nandroid Collection
http://forum.xda-developers.com/showthread.php?t=2200930
Click to expand...
Click to collapse
How can I superCID my phone if I cant boot into the rom?
I've never superCid, can't help you there.
Good news is you can get into bootloader still.
You could fastboot flash a boot.img and flash a rom in recovery.
Just need to mount usb storage in recovery to put the rom.zip on your phone.
Edit: reread that you tried that but rom didn't boot. Hopefully you waited 5-10 min for first load.
try wipedata/factory reset from CWM like 3 times then flashing?
Good luck to ya.
Edit 2: kind of wondering if you can run the Rogers RUU with that low of a bootloader (version-bootloader: 1.13.0000)
Maybe someone can chime in, because that would be nice not having to SuperCid.
Alright so I seemed to get it running on CM 10 by switching recoveries and flashing it's boot.
Then I was able to superCID the phone, which then lead my into S-off'ing it.
Then I was able to update the hboot firmware to 2.15
Cleared the cache and installed the new kernel and flashed cyanogenmod 10.1 rc
Everything went well after that. I did run into a laggy issue, which I then fixed by switching the CPU governor to ondemand instead of interactive.
Thanks for the post guys
Ok, I'll start from the beginning.
I purchased my phone from Rogers at April 2012. So it was Rogers stock 4.0.x rom, everything was locked at that time. I FORGOT the stock hboot/ruu version number for Rogers ONE XL.
From the time being, I rooted it, superCID, unlocked via HTC DEV. After these, I flashed customer recovery, and successfully flashed several roms from time being. Finally I stayed with ViperXL.
Then, facepalm s-off is released, and I s-offed my phone. Everything worked just fine.
The problem occurred when I started to flash sense 5 roms about couple weeks ago. I did not upgrade my firmware and I flashed sense 5 based roms (this is my bad), so I'm experiencing random reboot and signal drops. Then I upgraded my firmware using the instruction in this tread: http://forum.xda-developers.com/showthread.php?t=2423735 . I verified my installtion with ./fastboot gervar all . At this time, there were two warnings on the top of my bootloader: "tampered" and "unlocked".
So, at this time, I tried several sense 5 roms. My recovery at this time was TWRP 2.6.3.0. All the roms have one common problem on my phone: after I locked the screen and left my phone for a while, if I wanna wake my phone/display, nothing happened by pressing the power button. I have to press the power button for 10+ seconds to restart my phone. If I just left my phone for a short time and wake it, it will work properly.
I was thinking are these sense 5 problems, so I tried to flash cm roms yesterday. I followed the instructions in http://forum.xda-developers.com/showthread.php?t=2382933 to upgrade my RUU to 3.18. I flashed TWRP 2.6.3.0, and tried to flash cm 10.1 and 10.2. For cm 10.2, there were a lot of force close when I boot my phone. For cm 10.1, it is so unstable with random reboots as well as did not respond when I try to wake up the phone. I am not questioning CM's roms, I am sure there were something wrong with my phone or what I've done to it.
So, I tried to flash viper rom again with ruu 3.18 installed. The rom won't even boot...... However I found something interesting when I am flashing the viper rom. The size of ViperXL is 700+ MB while the size of CM 10.1 or 10.2 is around 180MB. The time it took to flash ViperXL was shorter than the time it took to flash CM roms.
Then I re-installed the RUU 3.18 update on my phone. Right now, the AT&T stock rom also will not respond after I left my phone idle for a moment......
User timmaaa kindly reminds me about something. I am posting the original post I started in another tread.
Originally Posted by snake3276120 View Post
After I ran the RUU 3.18 upgrade in this tread: http://forum.xda-developers.com/show....php?t=2382933
I boot into bootloader, and ran fastboot getvar all, the result is:
(bootloader) version: 0.5
(bootloader) version-bootloader: 2.14.0000
(bootloader) version-baseband: 0.24p.32.09.06
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 3.18.502.6
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) serialno: HT246W304864
(bootloader) imei: 359691041684351
(bootloader) product: evita
(bootloader) platform: HBOOT-8960
(bootloader) modelid: PJ8310000
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 4122mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-97c9a06e
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.061s
I'm assuming "(bootloader) version-main: 3.18.502.6" is the RUU version. I also flashed an hboot 2.14, it became 3.17.xxxxxxx. That'w why I am assuming this is the RUU number.
Ok, regardless of the build number or ruu...... I think there is something wrong with my bootloader. It doesn't matter which hboot I flash (hboot 2.14 with version-main 3.17/3.18, or hboot 2.15 with version-main 5.08), and I tried several twrp (2.4.4.0 and 2.6.3.0). The time it took to flash viper xl is really short while viper xl has 700MB. It is even shorter than the time I flash CM, which is around 180 MB. (Sorry for the bad English, I actually mean "The size of ViperXL is 700+ MB while the size of CM 10.1 or 10.2 is around 180MB. The time it took to flash ViperXL was shorter than the time it took to flash CM roms.")
I guess I'll start with the current AT&T stock rom (which still lose respond after I left the phone open for a while, and I have to press the power button for 10 secs to reset my phone)on hboot 2.14 and ruu 3.18. Root it, try to s-off again. Not sure if this will solve the problem.
Something interesting when I'm booting my phone, when the phone displays only the green HTC in the middle of the display, there is some text below it... saying something like "This is an internal build, do not distribute outside of HTC, failure may cause to law action". However, the AT&T stock rom I'm running right now does not have this.
timmaaa:
It's a bit hard to follow what you're saying there but here goes. It's not the RUU number it's the build number. An RUU is the program that updates your phone, the reason you see them referred to as the 3.18 RUU is because they're known by the build number that they update your phone to.
Did you check the md5 of the downloaded file as someone else suggested? It might be corrupt. Also, maybe you should try TWRP 2.6, versions 2.4.x and 2.5.x are well known as being very buggy, and I've seen people have issues with version 2.6.3 too. 2.6 is rock solid though.
The red text you see when the phone boots up is completely normal for a modified phone so you needn't worry about that. The reason the stock ROM doesn't have it is because the RUU has returned your phone to being completely stock, therefore not modified, therefore no red text.
Click to expand...
Click to collapse
Click to expand...
Click to collapse
OK, I am wondering where I can get my RUU number......
Also, in this case, what I should do now? Install TWRP 2.6.0.0 and try to flash everything again?
Currently "tampered" is gone from my bootloader, only "unlocked" stays there.
Lol you've kinda mashed my quote in with your post there so it's hard for people to see where they begin and end.
What do you mean you want to get your RUU number? Like I said an RUU is a program, what exactly do you mean?
Sent from my Evita
timmaaa said:
Lol you've kinda mashed my quote in with your post there so it's hard for people to see where they begin and end.
What do you mean you want to get your RUU number? Like I said an RUU is a program, what exactly do you mean?
Sent from my Evita
Click to expand...
Click to collapse
Because some posts are saying RUU 3.17 or 3.18, so I got confused...... but as long as it's a program, I will assume they are talking about the firmware or bootloader after running RUU 3.17 or 3.18 upgrade.
timmaaa said:
Lol you've kinda mashed my quote in with your post there so it's hard for people to see where they begin and end.
What do you mean you want to get your RUU number? Like I said an RUU is a program, what exactly do you mean?
Sent from my Evita
Click to expand...
Click to collapse
I fixed the qoute
Just to be clear, after you ran the 3.18 RUU you booted the phone without making any modifications and the problem was still occurring, right? It seems to me that it might be some kind of hardware problem that's causing a sleep of death every time the phone goes into sleep mode.
Sent from my Evita
timmaaa said:
Just to be clear, after you ran the 3.18 RUU you booted the phone without making any modifications and the problem was still occurring, right? It seems to me that it might be some kind of hardware problem that's causing a sleep of death every time the phone goes into sleep mode.
Sent from my Evita
Click to expand...
Click to collapse
That's right, I didn't even flash recovery... Well, my stock rom just self-rebooted, and stuck at booting animation while adb is still able to recognize it, and I can issue a reboot from adb. This also applies to my sense 5 roms.
If it's hardware problem, looks like upgrading to hboot 2.15 ruined my hardware, which is hard to believe...... Everything works fine before I upgrade my hboot to 2.15
Unfortunately it isn't under warranty anymore either.
Sent from my Evita
timmaaa said:
Unfortunately it isn't under warranty anymore either.
Sent from my Evita
Click to expand...
Click to collapse
I know... it is unfortunate...
timmaaa said:
Unfortunately it isn't under warranty anymore either.
Sent from my Evita
Click to expand...
Click to collapse
I upgraded my hboot to 2.15 and I flashed MaginRom 4.0. At least it's booting...... looks like my recovery hates aroma installer.
snake3276120 said:
I upgraded my hboot to 2.15 and I flashed MaginRom 4.0. At least it's booting...... looks like my recovery hates aroma installer.
Click to expand...
Click to collapse
Confirm your hboot and baseband version and post here. You said it upgraded, but let's make sure it actually was completely successful.
Also, I think TWRP 2.6.3 has some bugs, not sure if AROMA is one of them. You might check the TWRP thread. But I believe other 2.6.x versions are very stable. I've been on 2.6.0 for a while, and everything seems to be working great, and don't remember any bug reports on that version.
Yeah I can confirm I've seen folks with bugs on 2.6.3 but I've been using 2.6 for months and not a single problem (and no reports of bugs from others).
Sent from my Evita
timmaaa said:
Yeah I can confirm I've seen folks with bugs on 2.6.3 but I've been using 2.6 for months and not a single problem (and no reports of bugs from others).
Sent from my Evita
Click to expand...
Click to collapse
I used 2.6.0.0 to flash my current magiorom 4..... well at least it is usable now, with app/sense/notification bar/wake phone do not respond sometimes... I'm not blaming the rom, I am blaming my phone... probably now it's the time to get a new one lol
redpoint73 said:
Confirm your hboot and baseband version and post here. You said it upgraded, but let's make sure it actually was completely successful.
Also, I think TWRP 2.6.3 has some bugs, not sure if AROMA is one of them. You might check the TWRP thread. But I believe other 2.6.x versions are very stable. I've been on 2.6.0 for a while, and everything seems to be working great, and don't remember any bug reports on that version.
Click to expand...
Click to collapse
Here you are, boss.
PS E:\Program Files (x86)> cd '.\Minimal ADB and Fastboot'
PS E:\Program Files (x86)\Minimal ADB and Fastboot> .\fastboot.exe getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 2.15.0000
(bootloader) version-baseband: 1.31a.32.45.16_2
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 5.08.111.2
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) serialno:
(bootloader) imei:
(bootloader) product: evita
(bootloader) platform: HBOOT-8960
(bootloader) modelid: PJ8310000
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 3874mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-de589c6eef
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.061s
PS E:\Program Files (x86)\Minimal ADB and Fastboot>
Click to expand...
Click to collapse
I think the result is the same in thread http://forum.xda-developers.com/showthread.php?t=2423735
Quoted from the thread:
Install:
Installing the rom:
Download the rom and copy to your sdcard
Reboot to Recovery
Flash rom
I recommend you wipe data before or after flashing the rom
For root access, flash this: Flash this in recovery for root access
Reboot
OPTIONAL: Installing the Firmware (Warning: You MUST be S-OFF and Super CID to flash this! Flash at own risk!)
Reboot to bootloader (adb reboot bootloader if "USB Debugging" is enabled in Android)
Run: fastboot oem rebootRUU
Run: fastboot flash zip <PathToFirmware.zip>
If the output ends with "FAILED (remote: 90 hboot pre-update! please flush image again immediately)", run the previous command AGAIN
If it ends with "INFO..... OK", reboot to the bootloader: fastboot reboot-bootloader
Verify everything was successful by running: fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 2.15.0000
(bootloader) version-baseband: 1.31a.32.45.16_2
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 5.08.111.2
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) product: evita
(bootloader) platform: HBOOT-8960
(bootloader) modelid: PJ8310000
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 4140mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-de589c6eef
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
Click to expand...
Click to collapse
Reboot into Android: fastboot reboot or into recovery: fastboot reboot-recovery
Click to expand...
Click to collapse
Please refer to the attachment for a photo of my bootloader
Will TWRP 2.3.3.0 solve my problem? It looks like most roms recommend this recovery.... btw I'm running 2.6.0.0 at the moment.
No, changing TWRP won't solve your problem. You said you're using TWRP 2.6 now and that version is fine. I'd suggest trying one more time to do a clean flash, so wipe cache/dalvik cache/factory reset/system and install the ROM. Hell, do the wipe two or three times to be sure before installing.
Sent from my Evita
timmaaa said:
No, changing TWRP won't solve your problem. You said you're using TWRP 2.6 now and that version is fine. I'd suggest trying one more time to do a clean flash, so wipe cache/dalvik cache/factory reset/system and install the ROM. Hell, do the wipe two or three times to be sure before installing.
Sent from my Evita
Click to expand...
Click to collapse
lol thanks... Every time before I flash a new rom, I just format everything...
I don't know what to tell you then. There's nothing wrong with the ROMs you're using so it's either a case of user error or hardware failure of some kind.
Sent from my Evita
timmaaa said:
I don't know what to tell you then. There's nothing wrong with the ROMs you're using so it's either a case of user error or hardware failure of some kind.
Sent from my Evita
Click to expand...
Click to collapse
Thanks for all the help... I think it is hardware error... because I'm an electrical/computer engineer, I don't think I can't even handle flashing roms... Maybe I need to do more research lol
One XL is a nice phone, I don't wanna switch yet...
snake3276120 said:
Thanks for all the help... I think it is hardware error... because I'm an electrical/computer engineer, I don't think I can't even handle flashing roms... Maybe I need to do more research lol
One XL is a nice phone, I don't wanna switch yet...
Click to expand...
Click to collapse
Could you also try one last thing? Could you upgrade your twrp to latest release and try flashing cm 10.2 0310 nightly please.
Sent from my One X using Tapatalk 4
sandys1 said:
Could you also try one last thing? Could you upgrade your twrp to latest release and try flashing cm 10.2 0310 nightly please.
Sent from my One X using Tapatalk 4
Click to expand...
Click to collapse
Ok I'll do a backup and try tonight....latest twrp do u mean 2.6.3.0, or there is another new release?
Hi fellow XDA members. I am new to the HTC community so i can be considered as noob. A friend of mine gave me his HTC One S to try and fix it.
Currently i can get into the bootloader (its unlocked with HTC dev, and shows as tempered). I did a factory reset but this does not change anything. When i try to start the phone it sometimes loads correctly, but it can't last more that a minute in android. It freezes and starts rebooting several times. After that i can only shut it down through the bootloader.
These are the phone details:
(bootloader) version: 0.5
(bootloader) version-bootloader: 2.15.0000
(bootloader) version-baseband: 1.15.50.05.29
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 3.16.401.9
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno:
(bootloader) imei:
(bootloader) product: vle
(bootloader) platform: HBOOT-8960
(bootloader) modelid: PJ4010000
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 3987mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-64bedd38
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
After a lot of reading over the pass 2 days i realised that this phone is an S4 version (vle and it has a 1,5 processor).
From what i see the previous owner has flashed an S3 rom to an S4 handset.
If this is the case, can the phone be recovered from the DEAD????:angel:
Pretty much from what I can tell SOL for now. Tampered with s-on means that it was S-off previously. Plus the 3.16 firmware can only be flashed with S-off. Currently there is method to S-off 3.16. The easiest way to fix most issues is with a RUU but since 3.16 firmware was leaked and not official, there is no RUU at this time either.
I had the same problem previously but I was able to send it back to tmob for a warranty exchange.
Sent from my HTC One S using XDA Premium 4 mobile app
mjsheldon4 said:
Pretty much from what I can tell SOL for now. Tampered with s-on means that it was S-off previously. Plus the 3.16 firmware can only be flashed with S-off. Currently there is method to S-off 3.16. The easiest way to fix most issues is with a RUU but since 3.16 firmware was leaked and not official, there is no RUU at this time either.
I had the same problem previously but I was able to send it back to tmob for a warranty exchange.
Sent from my HTC One S using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Thanks for your reply. I do have some good news and bad news.
Good news is that i have managed to flash a 3.16 RUU.exe for S4. Tampered has gone (relock is still present).:victory:
Bad news is that phone does not boot to android and when it does is only for a few seconds. The more time is left switched off, the more time it can last in android. Even with safe mode, it still reboots.
I guess is a hardware problem.:crying:
What happens when it boots. Full android then turns off or stuck on HTC white screen. Does it say any thin?
Sent from my CM 10.1 Motorola Xoom Wingray!
mjsheldon4 said:
What happens when it boots. Full android then turns off or stuck on HTC white screen. Does it say any thin?
Sent from my CM 10.1 Motorola Xoom Wingray!
Click to expand...
Click to collapse
It stucks on the HTC logo and it keeps rebooting until i turn it off through the bootloader.
original21 said:
It stucks on the HTC logo and it keeps rebooting until i turn it off through the bootloader.
Click to expand...
Click to collapse
Hi.
Looks like a hardware issue to my, but there is more things to try.
It's good you have ran 3.16.401.8 JB RUU. You can S-OFF your phone now.
Can you run fastboot getvar all again and paste it here. Just to make sure the firmware in RUU was flashed correctly. If it was your hboot should be 2.15 and radio 1.11.
Sent from HTC One S using android 4.2.2 sense 5
tominozh said:
Hi.
Looks like a hardware issue to my, but there is more things to try.
It's good you have ran 3.16.401.8 JB RUU. You can S-OFF your phone now.
Can you run fastboot getvar all again and paste it here. Just to make sure the firmware in RUU was flashed correctly. If it was your hboot should be 2.15 and radio 1.11.
Sent from HTC One S using android 4.2.2 sense 5
Click to expand...
Click to collapse
I have a 2.15 hboot and 1.15 radio. Today I got an update for 3.16.401.9
Sent from my HTC One using XDA Premium 4 mobile app
So the phone's working now properly?
Sent from HTC One S using android 4.2.2 sense 5
tominozh said:
So the phone's working now properly?
Sent from HTC One S using android 4.2.2 sense 5
Click to expand...
Click to collapse
No. I still have the same problems. When its in android (even safe mode)after a few minutes it starts rebooting. When it reboots it stays at the HTC logo.
Sent from my HTC One using XDA Premium 4 mobile app
tominozh said:
So the phone's working now properly?
Sent from HTC One S using android 4.2.2 sense 5
Click to expand...
Click to collapse
Ok. I would try this. Run .8 RUU again. After that get root (or flash some jb 4.1.1 sense Rom) and flash unsecure kernel, like bulletproof for JB.
Then make sure you have supercid
and use facepalm method to get S-OFF. Then try downgrade to ics or upgrade your firmware to jb 4.2.2. I think it's worth a try.
Sent from HTC One S using android 4.2.2 sense 5
Resolved!
Apparently it was due to the fact that I installed Xposed Framework that causes the update process to fail.
I try to manually update the OTA.zip via stock recovery and found out that the process stopped at
"assert failed apply_patch_check( /system/bin/app_process."
Click to expand...
Click to collapse
Further checks showed that Xposed replaced the app_process file and causes it to fail checksum. I then copied /system/bin/app_process.orig back to /system/bin/app_process.
After that, the update was a breeze. The recovery used was from 3.15.707.4 (extracted from OTA.zip).
I've also S-OFF and Super-CID during my testing process.
If your update process stops after 25%, usually some checksum error has happened. Use manual update to determine the error message.
________________________________________________________________________
I'm having a problem updating my Butterfly to Android 4.3 from 4.2.2
My current firmware is 2.33.707.3 and the upgrade version is 3.15.707.4.
On my current phone, I have unlock my bootloader, flash recovery to TWRP 2.6.3.0 as well as rooted it. Due to inexperience, I did not backup my original recovery.
As per gleamed from this forum, I've tried to flash recovery from other stock ROM to proceed with the OTA update.
Steps taken:
Clicked Install now on the OTA message
Phone reboots to recovery
Phone icon with Green exclamation mark appears
Bottom part blue progress bar appears
Upon 30 to 40% progress, the screen changes to Red exclamation mark and update is stopped.
Edit: Did a Factory reset, problem remains.
I've tried the following recovery from other stock ROM without success.
Recovery from 3.15.707.4 (extracted OTA zip in phone's Download folder)
Recovery from 1.19.707.1 (extracted from DLXB1_U_JB_45_hTC_Asia_WWE_1.19.707.1_V0.0)
Recovery from 2.28.709.2 (extracted from OTA_DLXB1_U_JB_50_S_hTC_Asia_TW_2.28.709.2-1.18.709.3)
Recovery from 1.12.707.1
Recovery from 2.33 (from @Bassie39's OTA collection)
Recovery from 2.28.709.3
I've searched high and low for stock Recovery from 2.33.707.3 but unable to locate it.
Any tips or suggestion apart from S-OFF and update firmware, PL99img.zip update via bootloader, look in the OTA collection?
Code:
Model: Butterfly x920d
Android Version: 4.2.2
HTC Sense: 5.0
Software number: 2.33.707.3
CID: 044
[I][B]Bootloader Menu[/B][/I]
*** TAMPERED ***
*** UNLOCKED ***
DELUXE_UB1 PVT SHIP [B]S-ON[/B] RH
[B]HBOOT-1.54.0000[/B]
RADIO-3A.28.306.09
OpenDSP-V10.120.274.0520
[B]OS-2.33.707.3[/B]
eMMC-boot 2048MB
Aug 16 2013
[B][I]Fastboot getvar all results[/I][/B]
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.54.0000
(bootloader) version-baseband: 3A.28.306.09
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 2.33.707.3
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno: x
(bootloader) imei: x
(bootloader) meid: x
(bootloader) product: deluxe_ub1
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PL9911000
(bootloader) cidnum: HTC__044
(bootloader) battery-status: good
(bootloader) battery-voltage: 3856mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-0c6295fdaf
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
A list of posts with the same problem:
[Q] Help In Updating To 4.3 - Unsolved
Followed @bluheart suggestion - Not working
Try this buddy
Do everything as written.
bluheart said:
Try this buddy
Do everything as written.
Click to expand...
Click to collapse
@bluheart, How do I go from S-OFF to update my OTA? Is Rumrunner better?
Any help or advice would be very appreciated.
Sent from my HTC Butterfly using Tapatalk
Firewater or Rumrunner are equally effective.
I liked Firewater as its very simple to use.
What's the next step after having S-Off?
Sent from my HTC Butterfly using Tapatalk
kemikelx said:
What's the next step after having S-Off?
Sent from my HTC Butterfly using Tapatalk
Click to expand...
Click to collapse
Super cid
Sent from my HTC Butterfly s using XDA Premium 4 mobile app
After supercid flash the TW (Taiwan) firmware not the WWE (World Wide Edition) so that you get faster updates as this is a Taiwanese company. WWE gets updates a lot later (2-4 months later) so think about that.
abhinav.tella said:
After supercid flash the TW (Taiwan) firmware not the WWE (World Wide Edition) so that you get faster updates as this is a Taiwanese company. WWE gets updates a lot later (2-4 months later) so think about that.
Click to expand...
Click to collapse
Yes, This means I have to change the CID to HTC__621? But would this affect my Carrier settings?
kemikelx said:
Yes, This means I have to change the CID to HTC__621? But would this affect my Carrier settings?
Click to expand...
Click to collapse
No, I have done this with my old Butterfly without any bad effects or signal problems.
bluheart said:
Firewater or Rumrunner are equally effective.
I liked Firewater as its very simple to use.
Click to expand...
Click to collapse
Firewater didn't work. Instead I used Rumrunner.
Hope things worked out, and also I hope you took my advice and switched to Taiwan RUU.
You don't have to change CID if you are supercid which is 11111 something like that, you can install any RUU.
Sent from my LG-LS980 using XDA Premium 4 mobile app
abhinav.tella said:
Hope things worked out, and also I hope you took my advice and switched to Taiwan RUU.
You don't have to change CID if you are supercid which is 11111 something like that, you can install any RUU.
Sent from my LG-LS980 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I'm trying to find a way to install the Taiwanese RUU on my phone. Looking around this forum but some of the instructions are contradictory.
Any help or useful links to share?
kemikelx said:
I'm trying to find a way to install the Taiwanese RUU on my phone. Looking around this forum but some of the instructions are contradictory.
Any help or useful links to share?
Click to expand...
Click to collapse
Go to the unlock thread page 9, I posted a detailed S-Off procedure. Any further questions regarding TW firmware they can answer.
Hi guys, I'm new to installing custom roms. I've been reading for countless hours on the process before I attempt to install one. Here's where I'm at.
Phone: Verizon HTC One m8
1) Used Sunshine to get unlocked bootloader & S-OFF
2) I downloaded all OTA updates
3) Then flashed TWRP 3.0.2.0 and rooted with superSU
4) I immediately made a nandroid backup using TWRP
My phone's current state is working fine on stock rom.
Android 6.0
Sense 7.0
Here's my getvar all output:
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.14.20.0930
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 6.21.605.3
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) serialno: XXXXXXXXX
(bootloader) imei: XXXXXXXXXX
(bootloader) imei2: Not Support
(bootloader) meid: XXXXXXXXXX
(bootloader) product: m8_wlv
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B20000
(bootloader) cidnum: VZW__001
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 205bdca3
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
Click to expand...
Click to collapse
I want to install Android Revolution HD
I downloaded Android Revolution HD 53.1 which is Marshmallow (Android 6.0.0 + HTC Sense 7.0) according to their site.
I made one attempt to install that rom but it didn't work. Here's what I did:
1) Copied the rom zip to my sdcard
2) Entered recovery (TWRP)
3) Performed a Wipe in TWRP (default wipe settings)
4) Clicked Install, selected the Android Revolution zip.
The install screen came up, I went through the dialog and selected which apps I wanted to be installed in ARHD, and the install went through and eventually said Success. I rebooted the phone and was stuck in bootloop. So I restored to my nandroid backup and haven't tried again since.
I have read and re-read their instructions and am still not sure what I'm missing. Any help is greatly appreciated, and if you need any info just let me know. Thanks!
jdub55 said:
Hi guys, I'm new to installing custom roms. I've been reading for countless hours on the process before I attempt to install one. Here's where I'm at.
Phone: Verizon HTC One m8
1) Used Sunshine to get unlocked bootloader & S-OFF
2) I downloaded all OTA updates
3) Then flashed TWRP 3.0.2.0 and rooted with superSU
4) I immediately made a nandroid backup using TWRP
My phone's current state is working fine on stock rom.
Android 6.0
Sense 7.0
Here's my getvar all output:
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.14.20.0930
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 6.21.605.3
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) serialno: XXXXXXXXX
(bootloader) imei: XXXXXXXXXX
(bootloader) imei2: Not Support
(bootloader) meid: XXXXXXXXXX
(bootloader) product: m8_wlv
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B20000
(bootloader) cidnum: VZW__001
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 205bdca3
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
I want to install Android Revolution HD
I downloaded Android Revolution HD 53.1 which is Marshmallow (Android 6.0.0 + HTC Sense 7.0) according to their site.
I made one attempt to install that rom but it didn't work. Here's what I did:
1) Copied the rom zip to my sdcard
2) Entered recovery (TWRP)
3) Performed a Wipe in TWRP (default wipe settings)
4) Clicked Install, selected the Android Revolution zip.
The install screen came up, I went through the dialog and selected which apps I wanted to be installed in ARHD, and the install went through and eventually said Success. I rebooted the phone and was stuck in bootloop. So I restored to my nandroid backup and haven't tried again since.
I have read and re-read their instructions and am still not sure what I'm missing. Any help is greatly appreciated, and if you need any info just let me know. Thanks!
Click to expand...
Click to collapse
If I'm reading the op correctly I don't think that rom is compatible with the Verizon m8
Sent from my HTC One M8 using XDA Labs
jurington said:
If I'm reading the op correctly I don't think that rom is compatible with the Verizon m8
Click to expand...
Click to collapse
Ah shoot. I must have overlooked that. Okay, then how about this Verizon Stock Rooted rom?
Here's the thing. I really want a debloated rom. I'm not picky. It would be nice to get a stable custom rom that supports ART and is debloated. But I'm a bit confused.
It seems most of the stable roms are running Lollipop. Does this mean I need to downgrade somehow? Can I flash firmware, or do I need to do a actual factory reset? Please clarify this part, I think this is where I'm most confused at the moment.
jdub55 said:
Ah shoot. I must have overlooked that. Okay, then how about this Verizon Stock Rooted rom?
Here's the thing. I really want a debloated rom. I'm not picky. It would be nice to get a stable custom rom that supports ART and is debloated. But I'm a bit confused.
It seems most of the stable roms are running Lollipop. Does this mean I need to downgrade somehow? Can I flash firmware, or do I need to do a actual factory reset? Please clarify this part, I think this is where I'm most confused at the moment.
Click to expand...
Click to collapse
So for the most part just stay on marshmallow firmware. Everything I believe is compatible with it. And I'm running viper rom right now and it's pretty amazing. But just look in the Verizon m8 development and original development and you'll find roms that are compatible with it.
Sent from my HTC One M8 using XDA Labs
jurington said:
So for the most part just stay on marshmallow firmware. Everything I believe is compatible with it. And I'm running viper rom right now and it's pretty amazing. But just look in the Verizon m8 development and original development and you'll find roms that are compatible with it.
Sent from my HTC One M8 using XDA Labs
Click to expand...
Click to collapse
Oh okay. I actually already downloaded ViperOneM8 6.0.0 from their website. Is it safe to say I can perform a Wipe in TWRP, and then install the Viper rom and I should be good?
Also, just to clarify: I don't need to flash any firmware.zip?
Thanks so much.
jdub55 said:
Oh okay. I actually already downloaded ViperOneM8 6.0.0 from their website. Is it safe to say I can perform a Wipe in TWRP, and then install the Viper rom and I should be good?
Also, just to clarify: I don't need to flash any firmware.zip?
Thanks so much.
Click to expand...
Click to collapse
If you're already on the latest ota then you're good to go. And it'll have you perform a wipe through the aroma installer so no need to wipe before hand. And it's pretty slick, I just flashed it this morning and I'm liking it so far.
Sent from my HTC One M8 using XDA Labs
jurington said:
If you're already on the latest ota then you're good to go. And it'll have you perform a wipe through the aroma installer so no need to wipe before hand. And it's pretty slick, I just flashed it this morning and I'm liking it so far.
Click to expand...
Click to collapse
Thanks, I'm now running ViperOne!
I'm noticing a couple issues though:
1) The HTC Calendar app won't sync with my Google account. And my Google account isn't showing in the "Accounts" setting in Calendar. (I opted to not install Google Calendar during the rom install, but opted to install HTC Calendar)
2) None of the photos I've taken after installing V1 work with uFocus. I don't know if it's an issue with uFocus, or the dual lens. But when I go to edit a photo I took, I go into uFocus, and it says "Tap anywhere to adjust focus", but it doesn't matter where I tap, it doesn't adjust anything. Also, when taking a photo it doesn't tell me if my finger is blocking the 2nd lens. It will take the shot anyway, and if the 2nd lens was blocked, it will simply deny going into uFocus for that shot.
3) Is there any way to hide the Boomsound notification when playing audio?
If I can resolve these issues I can see myself sticking with this rom for a long time
jdub55 said:
Thanks, I'm now running ViperOne!
I'm noticing a couple issues though:
1) The HTC Calendar app won't sync with my Google account. And my Google account isn't showing in the "Accounts" setting in Calendar. (I opted to not install Google Calendar during the rom install, but opted to install HTC Calendar)
2) None of the photos I've taken after installing V1 work with uFocus. I don't know if it's an issue with uFocus, or the dual lens. But when I go to edit a photo I took, I go into uFocus, and it says "Tap anywhere to adjust focus", but it doesn't matter where I tap, it doesn't adjust anything. Also, when taking a photo it doesn't tell me if my finger is blocking the 2nd lens. It will take the shot anyway, and if the 2nd lens was blocked, it will simply deny going into uFocus for that shot.
3) Is there any way to hide the Boomsound notification when playing audio?
If I can resolve these issues I can see myself sticking with this rom for a long time
Click to expand...
Click to collapse
The first two issues are known about, and I don't know if it can be fixed since its a port from the HTC 10 and it's a completely different base than the m8 and if you follow the main thread and the Verizon for viper you see if there can be a fix. And I haven't looked hard to see if I can hide that dialogue but if I do I will definitely let you know.
Sent from my HTC One M8 using XDA Labs