I've got the Touch Pro (T7272-unlocked not t-Mobile branded) and am a T-Mobile customer.
Does anyone know if this device works on the T-Mobile 4G network?
If so, what setting, if any, need to be changed?
The package says the phone supports HSPA network, but T-Mobile's is HSPA+.
The phone will work, but I believe only on EDGE. The radio bands are wrong to get 3G or I guess 4G. There's nothing you can do about it.
Thanks for your reply.
I've used it for years with EDGE, which is brutally sloooooow.
I was wondering what spec determines if a phone will work on T-Mobile 4G network?
that is correct. att's 3/4g opperates arround 1800hmz while tmobiles 3/4g opperates around 1700mhz to no matter what you do (outside of switching carriers) there is no way you can opperate outside of edge
-rastlin
Rastin,
Thanks for your reply.
Is there any possibility that a software solution could change the Band Frequency?
Unfortunately it`s imposible.
Sorry for what is probably a stupid question.
I am thinking of buying an International version of the 7.0 plus (P6200) but I'm having a hard time figuring out which US Carrier, if any, (AT&T, T-Moble or Verizon) is fully compatible with the table's supported frequencies.
Any help in pointing me to the carrier, that will allow the tablet to get 3g data and allow the tablet to make phone calls, would be greatly appreciated.
Also, if you are using a P6200 in the US, I would be interested in what carrier you use, your opinions of the carrier and your opinion of the tablet in general.
Thank you
Over 140 views but no replies.
Does no one know the answer or is the question so simple it is basic knowledge I should already know?
I'm not familar witht eh international model but I can tell you that it won't work with Sprint or Verizon as they are CDMA and not GSM. So that leaves T-Mobile and AT&T and it would depend upon what frequency the GTab7+ recieves, is it tri-band (850, 1800, 1900) or just a single band? AT&T uses 850/1900 MHz and T-Moblile 1900 MHz for 3G service. I would assume that it would be tri-band as are so called "world phones".
TMo also requires UMTS1700.
So almost surely it will NOT get 3G service on TMo. That's why there is a special Tmo variant.
Don't know about AT&T
Thank you for your reply!
Here are the listed frequencies for the tablet
2G Network GSM 850 / 900 / 1800 / 1900
3G Network HSDPA 900 / 1900 / 2100
it appears that it supports all the frequencies for AT&T and T-Mobile. I guess my confusion is I can't tell if the tablet will support 3G or just 2G (wouldn't be worth it if all I could get is 2G).
Entropy512 said:
TMo also requires UMTS1700.
So almost surely it will NOT get 3G service on TMo. That's why there is a special Tmo variant.
Don't know about AT&T
Click to expand...
Click to collapse
Ahh, that is what I was looking for. As much as I dislike them, seems I will need to go with AT&T if I get this tablet.
Thank you very much, both of you!
Sorry I got a little confused between tabs and phones. Verizon uses EV-DO (CDMA based) for 3G and AT&T is HSDPA (GSM based) at 1900 MHz. T-Mobile uses 1700 and 2100 MHz for 3G.
warning, if you plan on using as phone and tab, at&t may want to make sure you are on tab data plan as well an it could be pricey for both.
with that being said Im using this on att with voice and unlimited grandfathered smartphone data. havent heard a word from them. I pray it stays this way. I will fight them for it.
conclusion: best mobile device in the world right now IMHO, until 7.7 comes out.
P6200 and iPhone SIM
Hi all,
just to make sure...
If I get the P6200, can I just pop my iPhone 3gs SIM with unlimited data plan (as long as I don't use it too much)?
I saw someone said they can do that on the 7.7 thread but I wanted to make sure the AT&T iPhone SIM isn't restricted to iPhones somehow.
Thanks
O
I have GT-P620900 from the Philippines and I am my tablet in the US now. I tested using at&t sim card and it works when I tried making a call using sim card (gsm).
Sent from my GT-P6200 using Tapatalk
Hi Neogrin,
With the posted frequencies:
2G Network GSM 850 / 900 / 1800 / 1900
3G Network HSDPA 900 / 1900 / 2100
it will work perfectly for 3G (HSDPA/HSPA+) speeds only on AT&T. You should get 2-4 Mbps downlink, or maybe even more with a good signal on AT&T.
Unfortunately for T-Mobile (whom I also prefer over AT&T), it will only work on their 2G network, at EDGE speeds, which would be about 200 Kbps if you are lucky. Actually, EDGE speeds are good enough for twitter, facebook, and a bit of surfing, but would be frustratingly slow for YouTube or downloading apps.
The Tab 7plus will NOT work on Sprint or Verizon as their CDMA, LTE, and WiMax networks are different technology from GSM and HSDPA and thus not compatible.
Internationally, the 7plus should work on almost any 2G or 3G network, with maybe a few country exceptions here and there.
BTW if you decide to activate your 7plus on AT&T, I can share a bit of experience. I received a Tab 7.7 3G this week, with a similar frequency list to the 7plus. (Unfortunately, it also lacks the "AWS" 1700/2100 band for T-Mobile). I went to an AT&T store today to activate the 7.7 on a month-to-month data plan, of US$25 for 2GB with US$10 per each 1GB of overage. They were not able to assign the data plan in their system to me, because the 7.7 3G is not an AT&T device. The same will be true for your 7plus. What they did to get it to work was to take the IMEI number from one of the other tablets they had on display in the store - making sure it was an HSDPA tablet, and not an LTE one - and used that to activate my account. It took them a while to figure this out, but when they did, it worked. Once the account was activated, and the SIM card was in my 7.7, it found AT&T service and I immediately got a welcome text message. However, data did not yet work - for that I had to do one more thing, which the staff did not know about (but luckily I did).
Go into Settings->Wireless and Networks->Mobile Network Settings
In there is an "Access Point Names" item.
Click on this, and you should see some entries. If it's a new AT&T SIM, it likely says "Cingular 410" or "wap.cingular" or something. This would be correct for a phone, but does not work with tablet data plans, so we need to add the correct one.
Bring up the menu, and there should be a "New APN" option. Select this. In the form which comes up, in the "Name" field, enter "broadband" (one word, no caps, without the quotes). In the "APN" field, do the same - "broadband" one word, no caps, no quotes.
Once you've done this, hit the menu again, and there should be a "Save" option. Choose this, and it will take you back to the list of APNs. Now in the list there should be an APN item called "broadband" which you just created. Press the radio button to the far right of the broadband item. It should turn green.
Give the tablet a few seconds, or a minute, and data should start working!
Hope this helps.
Craig
Hey guys i recently unlocked my HOX and tossed a T-Mobile chip in it. Is there a way for me to get a better data speed? I'm only able to use 2G at the moment.
You can't simply enable it, as T-Mobile uses the 1700 AWS spectrum for 3G/4G in most of their areas. The HOX doesn't support 1700. T-Mobile's older 2G network runs on 1900mhz, which the HOX will pick up, but you'll be limited to EDGE speeds.
There is good news though. T-Mobile is currently in the process of upgrading those areas to support 3G/4G on the 1900mhz spectrum they have. Their main goal is to attract iPhone customers (since the iPhone also cannot run on their 1700mhz network). From what I've heard they're doing a pretty good job, but until they get your area upgraded, you'll be stuck on EDGE.
Hope that explanation makes sense. If not, here's a decent writeup:
http://9to5mac.com/2012/05/07/t-mob...rk-in-large-number-of-markets-by-end-of-2012/
So T-Mobile seems to be ramping up their LTE coverage and my area seems to be one of the LTE markets.
I was wondering, would now be a good time to buy an AT&T Android LTE phone (like the Note 2 or GS3)?
I'm not entirely clear if the LTE on those AT&T phones will work with the current/future T-Mobile LTE network.
Right now I'm currently using an iPhone 4 on T-Mobile. I get spotty 3G coverage since I'm in one of the 1900MHz refarmed areas. Would using an AWS LTE compatible AT&T phone let me get T-Mobile LTE service?
Is T-Mobile eventually going to get rid of their 3G service on the 1700MHz frequency so they can use it for LTE and then put their 3G service on the 1900MHz frequency?
I can't afford a brand new phone, but when it comes to used phones it always seems that AT&T ones are cheaper to buy than T-Mobile equivalent.
Outrager said:
So T-Mobile seems to be ramping up their LTE coverage and my area seems to be one of the LTE markets.
I was wondering, would now be a good time to buy an AT&T Android LTE phone (like the Note 2 or GS3)?
I'm not entirely clear if the LTE on those AT&T phones will work with the current/future T-Mobile LTE network.
Right now I'm currently using an iPhone 4 on T-Mobile. I get spotty 3G coverage since I'm in one of the 1900MHz refarmed areas. Would using an AWS LTE compatible AT&T phone let me get T-Mobile LTE service?
Is T-Mobile eventually going to get rid of their 3G service on the 1700MHz frequency so they can use it for LTE and then put their 3G service on the 1900MHz frequency?
I can't afford a brand new phone, but when it comes to used phones it always seems that AT&T ones are cheaper to buy than T-Mobile equivalent.
Click to expand...
Click to collapse
It has been my understanding that AT&T and T-Mobile smartphones are network cross-compatible because they use the same bands for HSPDA and LTE. So as long as you have the following, you should be good to go.
First and most important: ***Phone Unlocked***
The correct sim for the carrier.
The correct APN settings for the carrier. (If this isn't auto-populated after the new sim is in the phone, you can search here on XDA for them.)
Lastly, apply any patches/fixes/tweaks for the particular device where needed. (if needed)
As for this network cross-compatibility changing in the future, odds are that it probably will not happen any time soon as this would be very costly for the carrier to change so soon after launching the LTE service. Post-LTE, maybe, but that is at least another 10 years away if I had to guess. :fingers-crossed:
I got a Jiayu G3 knowing it would be a gamble concerning whether or not it supported 3G on the AT&T network, which operates 3G on 850mhz and 1900mhz.
Naturally, I lost the gamble and was stuck with EDGE, or so I thought. I was driving around today, just 1-2 miles away from my home when I looked down at my phone and noticed the H over my cell signal. I ran a speed test and sure enough it confirmed HSPA due to the 4mb down and 1mb up speed. I even go to network provider search menu and it shows both AT&T 2G and 3G selections. Then as I went back home I noticed it was back to EDGE again. Now I have an old Samsung dumb phone that shows what band you are on in a developer menu, and I confirmed both 850mhz and 1900mhz bands have decent signals in my house, yet my Jiayu can't connect to it.
Can anyone help, this has really confused me.....
JonR1230 said:
I got a Jiayu G3 knowing it would be a gamble concerning whether or not it supported 3G on the AT&T network, which operates 3G on 850mhz and 1900mhz.
Naturally, I lost the gamble and was stuck with EDGE, or so I thought. I was driving around today, just 1-2 miles away from my home when I looked down at my phone and noticed the H over my cell signal. I ran a speed test and sure enough it confirmed HSPA due to the 4mb down and 1mb up speed. I even go to network provider search menu and it shows both AT&T 2G and 3G selections. Then as I went back home I noticed it was back to EDGE again. Now I have an old Samsung dumb phone that shows what band you are on in a developer menu, and I confirmed both 850mhz and 1900mhz bands have decent signals in my house, yet my Jiayu can't connect to it.
Can anyone help, this has really confused me.....
Click to expand...
Click to collapse
it use 2100Mhz only for 3G.
typical for china mobile phone...
use google chrome
open this http://www.ejiayu.com/Product-8.html
haybat said:
it use 2100Mhz only for 3G.
typical for china mobile phone...
use google chrome
open this http://www.ejiayu.com/Product-8.html
Click to expand...
Click to collapse
I think you missed the part that I actually get 3G in some areas, and it's definitely not on 2100MHz. It's 850 or 1900MHz.