[Q] Quick Help please - Galaxy Note 10.1 Q&A, Help & Troubleshooting

Hi
Below is the error I am getting while flashing the N8000
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_N8000DDBLL2_N8000ODDBLL2_541027_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> modem.bin
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
There is then a big red fail box and nothing else happens. During this whole process (about a minute) the screen on the note doesn't change at all.
The file I used in the PDA box is as follows: KIES_HOME_N8000DDBLL2_N8000ODDBLL2_541027_REV00_user_low_ship.tar.md5, only the Auto reboot, F reset and PDA were selected.
Please help

Usual if firmware file is faulty or the wrong format .
jje

It is fixed now.I will write small tutorial over this .. Its like everywhere its written but nowhere solution is given ...I will start a new thread to discuss step by step fix ...

Related

[Q] Samsung Tab 3 8.0 SM-T310 HELP!

I have got stuck in a boot loop, i forgot to make a backup in PhilZ Touch Advanced CWM Recovery and i've tried to restore to the original file with Odin3 V. 3.09 and
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T310UEUAMH2_T310XARAMH2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
this pops up. I have done the download mode and http://forum.xda-developers.com/showthread.php?t=2618798 tried using this tool so i could go to the stock firmware so far nothing is working. PLEASE HELP

[Q] Samsung galaxy s3 lte odin problem

hi, i have a problem with my galaxy s3 lte. i was trying to root the phone and somehow i bricked it . i tried to install the stock firmware android 4.3 through odin, i put it in the pda section but it keeps failing.
This is the log.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGNJ2_I9300MSTGNJ1_I9300XXUGNA8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> modem.bin
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
im sure im using the correct file, i tried different usb cables but it wont work. i cant use kies because my pc doesn't detect the phone just odin does.
please help if you can

Galaxy S6 sm g920t - boots with sounds but no picture (all black screen fixes no fix)

hey everyone i have my Galaxy s6 from t mobile rooted and one day i went to power it on and it shows pictures for the Galaxy S6 screen but no picture comes up after the Tmobile Sounds boot screen. I have attempted all black screen fixes i can find as well as TWRP recovery and i cant seem to get the correct file? or something always goes wrong in odin when i try to install the stock firmware. not sure what else to try if anyone has any ideas or needs more information please let me know. thank you.
After It fails my download screen on phone says SW REV. CHECK FAIL. DEVICE:3, BINARY:2
***ODIN LOG***
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920TUVU2COF6_G920TTMB2COF6_G920TUVU2COF6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

s7 G930F wotn flash with odin

Hello i been getting this short of message while im trying to flash it
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1101)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
if i flash the AP on its own i i get recovery.img fail
ps. the mobile wont turn on and stucks on loading screen of twrp cant access recovery cant access the rom nothing just download mode
What firmware did you have?
What country are you in?
What firmware are you trying flash?

Could not do normal boot , invalid kernel length on sm-g570f

my phone is kinda stuck on bootloop with the same error in red letters "Could not do normal boot , invalid kernel length" , sadly the usb debbuging option wasn't turned on before the problem sowhenever i try flashong stock rom it doesn't work , if i try flashing ap bl csc cp , i get re partion operation failed and if i check the box it also fails saying couldn't open specified file , but when i try to flash only ap i get another error which is Complete(Write) operation failed. any solution pls ?
K1RA10 said:
my phone is kinda stuck on bootloop with the same error in red letters "Could not do normal boot , invalid kernel length" , sadly the usb debbuging option wasn't turned on before the problem sowhenever i try flashong stock rom it doesn't work , if i try flashing ap bl csc cp , i get re partion operation failed and if i check the box it also fails saying couldn't open specified file , but when i try to flash only ap i get another error which is Complete(Write) operation failed. any solution pls ?
Click to expand...
Click to collapse
Try flashing without using the re-partition option, just flash the firmware files without changing any of the settings and options in Odin, Odin's default settings should be all you need.
Droidriven said:
Try flashing without using the re-partition option, just flash the firmware files without changing any of the settings and options in Odin, Odin's default settings should be all
Droidriven said:
Try flashing without using the re-partition option, just flash the firmware files without changing any of the settings and options in Odin, Odin's default settings should be all you need.
Click to expand...
Click to collapse
so after some tries my problem can be summarized as, if i flash all the firmware ( AP+CSC+BL+CP) i get the re partition error but when i flash only AP ia get the complete(write) operation failed , also i can't flash twrp recovery cause ot says frp lock on, any solution?
Click to expand...
Click to collapse
K1RA10 said:
so after some tries my problem can be summarized as, if i flash all the firmware ( AP+CSC+BL+CP) i get the re partition error but when i flash only AP ia get the complete(write) operation failed , also i can't flash twrp recovery cause ot says frp lock on, any solution?
Click to expand...
Click to collapse
Yes, I understand what you said in your first post.
Are you selecting the "re-partition" option in Odin when you flash the firmware or are you not selecting the "re-partition" option when you flash the firmware? You should not be getting the re-partition error unless you are using the re-partition option when you flash the firmware, if this is what you are doing, try flashing without using the re-partition option.
Try finding the newest version of engineering firmware for your specific model number, if one exists for your model and is available to the public. Engineering firmware can be used to fix the FRP lock. Do some Google searching to learn how to use the engineering firmware to fix FRP lock.
Droidriven said:
Yes, I understand what you said in your first post.
Are you selecting the "re-partition" option in Odin when you flash the firmware or are you not selecting the "re-partition" option when you flash the firmware? You should not be getting the re-partition error unless you are using the re-partition option when you flash the firmware, if this is what you are doing, try flashing without using the re-partition option.
Try finding the newest version of engineering firmware for your specific model number, if one exists for your model and is available to the public. Engineering firmware can be used to fix the FRP lock. Do some Google searching to learn how to use the engineering firmware to fix FRP lock.
Click to expand...
Click to collapse
so now that i have tried the engineering firmware (combination file) , i still get the re partition error even tho i have this option unchecked in odin , and when i try to flash stock firmware or latest firmware i get the complete write error
this is what i get wheen i flash stoock rom,( re partition is unchecked)
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3364 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
this is what i get when i check the re partition
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3364 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Can't open the specified file. (Line: 2006)
<OSM> All threads completed. (succeed 0 / failed 1)
-----------------------------------------------------------------------------
now flashing with latest rom
re partition unchecked :
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 4019 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
re partition checked :
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 4019 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Can't open the specified file. (Line: 2006)
<OSM> All threads completed. (succeed 0 / failed 1)
-----------------------------------------------------------------------------
flashing only ap without and after adding pit file :
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3826 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3826 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
K1RA10 said:
this is what i get wheen i flash stoock rom,( re partition is unchecked)
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3364 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
this is what i get when i check the re partition
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3364 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Can't open the specified file. (Line: 2006)
<OSM> All threads completed. (succeed 0 / failed 1)
-----------------------------------------------------------------------------
now flashing with latest rom
re partition unchecked :
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 4019 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
re partition checked :
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 4019 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Can't open the specified file. (Line: 2006)
<OSM> All threads completed. (succeed 0 / failed 1)
-----------------------------------------------------------------------------
flashing only ap without and after adding pit file :
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3826 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3826 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
It seems to be connecting and disconnecting, are you sure that you are using a good cable and have it securly connected to the device? It also seems to be having trouble finding or loading your PIT file. You may have to download a PIT file for your specific device model number, if it is available for download.
Let me do some searching to see what your specific errors that it is reporting mean and I'll post here with what I find.
Droidriven said:
It seems to be connecting and disconnecting, are you sure that you are using a good cable and have it securly connected to the device? It also seems to be having trouble finding or loading your PIT file. You may have to download a PIT file for your specific device model number, if it is available for download.
Let me do some searching to see what your specific errors that it is reporting mean and I'll post here with what I find.
Click to expand...
Click to collapse
about the connection and disconnecting issue, it's cause when i flash and it doesn't work i have to get out of download mode and get back in, that's why it appears as added and removed, and about the pit file i found one and loaded it but as you see re partition error, thank you for the efforts
K1RA10 said:
about the connection and disconnecting issue, it's cause when i flash and it doesn't work i have to get out of download mode and get back in, that's why it appears as added and removed, and about the pit file i found one and loaded it but as you see re partition error, thank you for the efforts
Click to expand...
Click to collapse
Have you tried turning off antivirus? It can cause a myriad of errors in Odin.
Droidriven said:
Have you tried turning off antivirus? It can cause a myriad of errors in Odin.
Click to expand...
Click to collapse
i turned antivirus off and tried to flash stock rom i got this new error :
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3248 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
----------------------------------------------------------------------------
while flashing twrp gives :
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 22 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and the phone saying Custom Binary(RECOVERY) Blocked By FRP Lock
K1RA10 said:
i turned antivirus off and tried to flash stock rom i got this new error :
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3248 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
----------------------------------------------------------------------------
while flashing twrp gives :
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 22 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and the phone saying Custom Binary(RECOVERY) Blocked By FRP Lock
Click to expand...
Click to collapse
K1RA10 said:
i turned antivirus off and tried to flash stock rom i got this new error :
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3248 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
----------------------------------------------------------------------------
while flashing twrp gives :
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 22 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and the phone saying Custom Binary(RECOVERY) Blocked By FRP Lock
Click to expand...
Click to collapse
Can you still boot into stock recovery? If you can, factory reset your device while in recovery then boot into download mode. Flash the stock firmware, this time try enabling the "re-partition" option in Odin. Then, if you have a copy of your PIT file, select the PIT tab in Odin and place the PIT file in its slot then click Start to begin the flash.
Droidriven said:
Can you still boot into stock recovery? If you can, factory reset your device while in recovery then boot into download mode. Flash the stock firmware, this time try enabling the "re-partition" option in Odin. Then, if you have a copy of your PIT file, select the PIT tab in Odin and place the PIT file in its slot then click Start to begin the flash.
Click to expand...
Click to collapse
i can only boot into dowload mode
Hi;
My friend installed a wrong TWRP for Note 9 N960N and Later.
In the screen appears that’s message:” Could Not normal boot invalid kernel length”
I pull all buttons Vol Up + Power, Vol down + Power, Vol Up + Bixby + Power, Vol down + Bixby + Power, and nothing happened. Stay in the Sam message:” Could Not normal boot invalid kernel length”
Please Any Help?

Categories

Resources