[Q] Help with booting loop please - Verizon Samsung Galaxy S III

I searched around and couldn't find how to fix my booting problem. I have a Verizon Galaxy S3. I was rooted, installed ezlocked and unlocked it. I then installed ezrecovery and did a back up. Then I wiped everything on and it and tried to install CM10. It failed, so I rebooted and everything went back to stock. I repeated the ezunlock and ezrecovery and then attempted to install CM10 without wiping the data/cache(because I'm an idiot). Now when I start the phone it takes me right into the CM10 booting animation. I can't get into download mode or recovery mode. Whenever I try to get into those it takes me right back into the booting animation. Battery pulls do nothing.
I know I'm a noob and I can't believe I did this. I can't get back into CWM or download mode so I can flash through Odin. Any help would be really appreciated.

Tyjames48 said:
I searched around and couldn't find how to fix my booting problem. I have a Verizon Galaxy S3. I was rooted, installed ezlocked and unlocked it. I then installed ezrecovery and did a back up. Then I wiped everything on and it and tried to install CM10. It failed, so I rebooted and everything went back to stock. I repeated the ezunlock and ezrecovery and then attempted to install CM10 without wiping the data/cache(because I'm an idiot). Now when I start the phone it takes me right into the CM10 booting animation. I can't get into download mode or recovery mode. Whenever I try to get into those it takes me right back into the booting animation. Battery pulls do nothing.
I know I'm a noob and I can't believe I did this. I can't get back into CWM or download mode so I can flash through Odin. Any help would be really appreciated.
Click to expand...
Click to collapse
Did you try holding the power button, up on the volume, and the home button when you boot the phone to get to CWM?
Sent from my SCH-I535 using xda app-developers app

do you have the sdk set up? can you use adb?

Were you on a JellyBean baseband? If so to enter recovery you have to let go of the power button on the vibrate and keep pressing the home key + vol up.

x714x said:
Were you on a JellyBean baseband? If so to enter recovery you have to let go of the power button on the vibrate and keep pressing the home key + vol up.
Click to expand...
Click to collapse
I was going from stock ICS to CM10. But yeah, you were right. I tried like a hundred different ways to try to get into download mode. I finally got it to work and then flashed through Odin. Thanks everybody! I feel like a dumbass.

Related

Bricked G2x, Tried everything

My G2x is bricked. I have tried following this guide, but it did nothing, http://forum.xda-developers.com/showthread.php?t=1
I have tried using NVFlash to flash to stock, Flash CWM on it, but nothing seems to happen. This is the result of flashing stock recovery
http://gyazo.com/111d4f87503e91a3cd92b8a803d5bb46
After doing so, I try to boot into recovery but nothing happens. The screen lights up and shows the pure white LG sign with no colors on the side. No matter how long I hold vol DOWN and power, it doesn't want to boot into recovery. I am unsure of what to do now. Could someone help me?
hyudryu said:
My G2x is bricked. I have tried following this guide, but it did nothing, http://forum.xda-developers.com/showthread.php?t=1
I have tried using NVFlash to flash to stock, Flash CWM on it, but nothing seems to happen. This is the result of flashing stock recovery
http://gyazo.com/111d4f87503e91a3cd92b8a803d5bb46
After doing so, I try to boot into recovery but nothing happens. The screen lights up and shows the pure white LG sign with no colors on the side. No matter how long I hold vol DOWN and power, it doesn't want to boot into recovery. I am unsure of what to do now. Could someone help me?
Click to expand...
Click to collapse
You cannot boot into stock recovery on a G2X. For stock you use volume up and power and it just does a factory reset and reboots your device.
You need to flash CWM Recovery. Then you enter recovery by holding Volume Down and Power and use CWM to reformat your system and flash a rom.
If CWM doesn't work then you need to use the KDZ method to reflash your device to stock.
Don't worry it is almost impossible to fully brick a G2X. As long as you can use NVFlash the device should be recoverable.
My phone isn't stock. I had CWM on it, and I flashed PhoenixBlood ROM. When I tried to upgrade the ROM by flashing the new one, my phone ended up like this. I was able to boot into CWM by holding Vol DOWN and power, but not anymore. Right now, I can't even get into recovery.
hyudryu said:
My phone isn't stock. I had CWM on it, and I flashed PhoenixBlood ROM. When I tried to upgrade the ROM by flashing the new one, my phone ended up like this. I was able to boot into CWM by holding Vol DOWN and power, but not anymore. Right now, I can't even get into recovery.
Click to expand...
Click to collapse
It doesn't matter what your phone is. Use this method to unbrick your G2x:
http://forum.xda-developers.com/showthread.php?t=1248644
There are a couple more methods found on XDA too. Please search before posting.
hyudryu said:
My phone isn't stock. I had CWM on it, and I flashed PhoenixBlood ROM. When I tried to upgrade the ROM by flashing the new one, my phone ended up like this. I was able to boot into CWM by holding Vol DOWN and power, but not anymore. Right now, I can't even get into recovery.
Click to expand...
Click to collapse
Did you install CWM using ROM Manager?

Corrupted CWMR? Boot loop

Hey all, first time posting here,
So, I rooted my phone a few days ago and flashed Invisiblek's CM10(Running the August 10th build), using the instructions found here. Haven't had any problems at all until now. I had to reboot my phone, and now it's stuck in a boot loop. The CWMR screen is missing the background, and it won't let me boot into ODIN mode. What do I do?
Thank you for any help!
Krog216 said:
Hey all, first time posting here,
So, I rooted my phone a few days ago and flashed Invisiblek's CM10(Running the August 10th build), using the instructions found here. Haven't had any problems at all until now. I had to reboot my phone, and now it's stuck in a boot loop. The CWMR screen is missing the background, and it won't let me boot into ODIN mode. What do I do?
Thank you for any help!
Click to expand...
Click to collapse
You should be able to boot into odin by taking the battery out, and then putting it back in while holding Volume Down + Home + Power at the same time. And then just flash a stock or stock rooted image in odin.
There we go. Thank you very much!
Flashed the ROM linked from here. Now I'm stuck on the 4G LTE screen. Suggestions?
Flashed it again. Still nothing. Did I brick it?
If you can get into Odin mode, I suggest flashing back go stock and starting over. If you can't get Odin to work, or even enter download mode then you might have other problems.
Sent from my SCH-I535 using Tapatalk 2
I am (thankfully) able to get into odin mode. Where can I get the stock ROM for the US VZW version? I haven't been able to find that anywhere, and the thread on here only has dead links.
Flashed again, still nothing. I get stuck at the 4G LTE loading screen.
Found a stock ROM and flashed back to it. Still stuck at that screen. Did I brick it?
dont forget to wipe data/cache...
it happens
you can do this by booting into stock recovery
Volume UP + Home + power.
vega04 said:
dont forget to wipe data/cache...
it happens
you can do this by booting into stock clock work
Volume UP + Home + power.
Click to expand...
Click to collapse
Oh my god I love you.
It works!!!
Krog216 said:
Oh my god I love you.
Click to expand...
Click to collapse
i love you too.. lol ive been there..
So, I've got it worked out so that I have a recovery image made of a rooted version of the stock ROM. However, I SWEAR a kitten dies every time I look at the TouchPiss interface, but whenever I try to flash Invisiblek's CM10 I get stuck in a boot loop. Any ideas as to what's causing it? I've tried clearing data/cache/davlik cache before flashing the ROM, after flashing the ROM...
Would there be any way at all that I could flash it through ODIN?

[Q][SOLVED] Help!

[Q] Help!
Okay. So i just rooted my phone yesterday and i flashed a ROM. Well I forgot to backup all my apps and such. So I went back into CWM and I cleared data and flashed my nandroid recovery file. That completed successfully, so I push restart system at the top. Well now it is just stuck in the boot screen and won't do anything. How do I fix this! HELP!
atech087 said:
Okay. So i just rooted my phone yesterday and i flashed a ROM. Well I forgot to backup all my apps and such. So I went back into CWM and I cleared data and flashed my nandroid recovery file. That completed successfully, so I push restart system at the top. Well now it is just stuck in the boot screen and won't do anything. How do I fix this! HELP!
Click to expand...
Click to collapse
I can't get into CWM either. It just keeps rebooting and getting stuck on the boot screen.
For getting back to CWM, pull the battery (USB unplugged) so it turns off fully, put the battery back in, hold the volume up and down both on the left, and turn it on (hold power until you see something, let go of power but keep holding the volume keys). Once you see CWM come on, you can let go of the volume keys.
You flashed what from what? If what you flashed isn't the same major OS version, the nandroid backup is probably only going to be helpful through Titanium Backup or some other program since you won't be able to flash it successfully.
Theraze said:
For getting back to CWM, pull the battery (USB unplugged) so it turns off fully, put the battery back in, hold the volume up and down both on the left, and turn it on (hold power until you see something, let go of power but keep holding the volume keys). Once you see CWM come on, you can let go of the volume keys.
You flashed what from what? If what you flashed isn't the same major OS version, the nandroid backup is probably only going to be helpful through Titanium Backup or some other program since you won't be able to flash it successfully.
Click to expand...
Click to collapse
Ok so I tried to get back into CWM and it was unsuccessful. It just gets stuck on the boot screen still. I flashed my 2.3.6 stock rooted nandroid backup from this custom rom: http://forum.xda-developers.com/showthread.php?t=1404863 . I can still get to recovery mode just not CWM. Any ideas?
Okay... recovery mode but not CWM... what does that mean?
CWM IS recovery mode. Are you trying to get into download mode instead? For that, battery pull, battery in, plug in USB to computer, hold volume... up (I think), turn on (power button until the screen lights up), let go of power, should be in download mode.
Theraze said:
Okay... recovery mode but not CWM... what does that mean?
CWM IS recovery mode. Are you trying to get into download mode instead? For that, battery pull, battery in, plug in USB to computer, hold volume... up (I think), turn on (power button until the screen lights up), let go of power, should be in download mode.
Click to expand...
Click to collapse
Yeah.. I meant i couldn't get into recovery mode but I can get into download mode. Do you think this would get my phone working again? http://forum.xda-developers.com/showthread.php?t=1358498
Working as a phone, yes. If you can get into download mode, you should be able to flash stuff. If you flashed from Froyo to GB-custom, use the one-click twice... first to get the basic ROM over, then tell it to do bootloaders as well. If you flashed from GB to GB-custom, then you only need to flash once.
I'd suggest using the second link, BWaT+stock. Basically, from here:
http://forum.xda-developers.com/showthread.php?t=1822626
If you have any problems, make sure you're following the guide fully:
http://forum.xda-developers.com/showpost.php?p=21953878&postcount=2
After you get it booting up with root, you can extract apps from the nandroid using Titanium Backup or something else similar.
Theraze said:
Working as a phone, yes. If you can get into download mode, you should be able to flash stuff. If you flashed from Froyo to GB-custom, use the one-click twice... first to get the basic ROM over, then tell it to do bootloaders as well. If you flashed from GB to GB-custom, then you only need to flash once.
I'd suggest using the second link, BWaT+stock. Basically, from here:
http://forum.xda-developers.com/showthread.php?t=1822626
If you have any problems, make sure you're following the guide fully:
http://forum.xda-developers.com/showpost.php?p=21953878&postcount=2
After you get it booting up with root, you can extract apps from the nandroid using Titanium Backup or something else similar.
Click to expand...
Click to collapse
Thanks. I used http://forum.xda-developers.com/showthread.php?t=1358498 this and am just going to reboot and everything all over again using this guide http://forum.xda-developers.com/showthread.php?t=1470716 and hope I don't have this problem again. Thanks for your help!!!!!

[Q] Recovery Boot Loop Problem

Had a problem. Hope someone with experience can give me a few answers.
Nave new t-mobile Note 3, SM-N900T. Stock 4.4.2 KitKat Touchwiz rooted.
Rooted to enable SDFix to use SD card as I want to use it.
Everything great! No problems.
Thought it would be wise to have a Nanoid backup.
Opened Rom Manager and made One change in prefrences. I set it for external SD card storage. (mistake?)
Went to 'Backup current Rom' in Rom manager, started it and it started to reboot. Shut down and restarted in a 'Recovery' boot loop??
No matter what I did, Tried holding power, up volume and home button, nothing. Boot loop continued. Removed battery, waited, as soon as I re-installed battery it instantly went back into recovery boot loop.
I don't know what I did, I kept removing battery and trying again and again and all of a sudden, it booted up back to KitKat and now everything is working great again. No problem on any standard reboot.
What happened? I have used this same set up on my S3 and never had a problem.
I would like to backup the current setup for any future problems. But now, I'm afraid to even try.
I removed Rom Manager and re-installed. Made sure that the storage location was reset to internal and it should be OK??
What did I do when I got out of the Recovery boot loop??
So, afraid to try again. Don't want the boot loop again.
rspilot1 said:
Had a problem. Hope someone with experience can give me a few answers.
Nave new t-mobile Note 3, SM-N900T. Stock 4.4.2 KitKat Touchwiz rooted.
Rooted to enable SDFix to use SD card as I want to use it.
Everything great! No problems.
Thought it would be wise to have a Nanoid backup.
Opened Rom Manager and made One change in prefrences. I set it for external SD card storage. (mistake?)
Went to 'Backup current Rom' in Rom manager, started it and it started to reboot. Shut down and restarted in a 'Recovery' boot loop??
No matter what I did, Tried holding power, up volume and home button, nothing. Boot loop continued. Removed battery, waited, as soon as I re-installed battery it instantly went back into recovery boot loop.
I don't know what I did, I kept removing battery and trying again and again and all of a sudden, it booted up back to KitKat and now everything is working great again. No problem on any standard reboot.
What happened? I have used this same set up on my S3 and never had a problem.
I would like to backup the current setup for any future problems. But now, I'm afraid to even try.
I removed Rom Manager and re-installed. Made sure that the storage location was reset to internal and it should be OK??
What did I do when I got out of the Recovery boot loop??
So, afraid to try again. Don't want the boot loop again.
Click to expand...
Click to collapse
Hi. What recovery are you using?
If you haven't installed a custom recovery, then that explains your issue. Basically, the app scheduled a custom recovery script which kept failing in the stock recovery. You should normally be able to reboot into the system holding the power button, thus skipping going to recovery. This also resets the recovery script so everything is back to normal.
Nandroid is normally only possible using a custom recovery like TWRP or CWM.
I saw that you might be able to perform a Nandroid without restarting the phone (so without a custom recovery) using this app: https://play.google.com/store/apps/details?id=com.h3r3t1c.onnandbup&hl=en
I have never tried it. Looks promising though.
But please note that you won't be able to restore the backup without a custom recovery.
EDIT: If you do have a custom recovery, why not boot in recovery mode and make the backup from there?
Cheers
Recovery Boot Loop Problem
I have CWM installed. Setup thru Rom Manager as I have done before on other phones.
Tried it again, same thing. Over and over. Constant reboot. Dosen't matter if I hold the power button or try different ways, same thing.
It says: Recovery booting
Recovery is not seandroid enforcing
Set warranty bit:recovery
If I remove battery and wait a couple of minutes, I can install battery and it dosen't start till I hold power button.
So I held volume down, home button and power button and booted into download mode. From there I cancelled and it rebooted normally.
Everything I've read on boot loops always say 'boot into recovery'. I only wish I could. That's the bootloop.
Any idea on what's wrong?
Thank you for your time and trouble.
rspilot1 said:
I have CWM installed. Setup thru Rom Manager as I have done before on other phones.
Tried it again, same thing. Over and over. Constant reboot. Dosen't matter if I hold the power button or try different ways, same thing.
It says: Recovery booting
Recovery is not seandroid enforcing
Set warranty bit:recovery
If I remove battery and wait a couple of minutes, I can install battery and it dosen't start till I hold power button.
So I held volume down, home button and power button and booted into download mode. From there I cancelled and it rebooted normally.
Everything I've read on boot loops always say 'boot into recovery'. I only wish I could. That's the bootloop.
Any idea on what's wrong?
Thank you for your time and trouble.
Click to expand...
Click to collapse
Have you tried booting directly into recovery?
So just shut off your phone and then open it by holding volume up + home + power. It should boot into recovery. If it doesn't, I recommend installing cwm or TWRP using Odin instead of Rom manager.
Might be a problem with your current recovery.
Sent from my GT-I9505
Recovery Boot Loop Problem
andreiav said:
Have you tried booting directly into recovery?
So just shut off your phone and then open it by holding volume up + home + power. It should boot into recovery. If it doesn't, I recommend installing cwm or TWRP using Odin instead of Rom manager.
Might be a problem with your current recovery.
Sent from my GT-I9505
Click to expand...
Click to collapse
Yes, I tried. Does the same thing.
I've never used Odin. All the info I've read mentioned downloading USB drivers and using different .tar files. Checking this and that.
Nothing I've ever done.
No experience with it.
Never had a reason before to use it.
Every instruction website I've read all seem to be different.
I'm gonna have to find out, huh? lol
I've got Odin on my computer, and have the CWM 6 zipped file.
Will do some research.
Thanks
rspilot1 said:
Yes, I tried. Does the same thing.
I've never used Odin. All the info I've read mentioned downloading USB drivers and using different .tar files. Checking this and that.
Nothing I've ever done.
No experience with it.
Never had a reason before to use it.
Every instruction website I've read all seem to be different.
I'm gonna have to find out, huh? lol
I've got Odin on my computer, and have the CWM 6 zipped file.
Will do some research.
Thanks
Click to expand...
Click to collapse
No problem.
A few tips with odin:
-If you have Kies installed, you don't need to install other drivers.
-The file you flash with Odin should have tar or tar.md5 extension
-you have to activate USB debugging from developer options.
-boot your phone into download mode
-run Odin as administrator
-connect your phone. you should see the text Added in Odin. If don't see it, you need drivers.
-you should make sure only auto reboot and f. Reset time are checked
-you should put the file in Pda or Ap(if using latest version)
Click start and wait until it finishes. It will restart itself if you checked auto reboot.
That's about it. It's very safe and easy to use.
Watch some videos on YouTube. You will definitely find some.
Cheers
Sent from my GT-I9505
Recovery Boot Loop Problem
andreiav said:
No problem.
A few tips with odin:
-If you have Kies installed, you don't need to install other drivers.
-The file you flash with Odin should have tar or tar.md5 extension
-you have to activate USB debugging from developer options.
-boot your phone into download mode
-run Odin as administrator
-connect your phone. you should see the text Added in Odin. If don't see it, you need drivers.
-you should make sure only auto reboot and f. Reset time are checked
-you should put the file in Pda or Ap(if using latest version)
Click start and wait until it finishes. It will restart itself if you checked auto reboot.
That's about it. It's very safe and easy to use.
Watch some videos on YouTube. You will definitely find some.
Cheers
Sent from my GT-I9505
Click to expand...
Click to collapse
Thank you, that answered some questions.
you've been a great help.
Recovery Boot Loop Problem
rspilot1 said:
Thank you, that answered some questions.
you've been a great help.
Click to expand...
Click to collapse
Update: The install of CWM with Odin seemed to be successful. Still have same problem.
I believe the problem must be somewhere else.
Something is stopping the recovery boot. More research ahead.
When I find out more, will post here and give update.
rspilot1 said:
Update: The install of CWM with Odin seemed to be successful. Still have same problem.
I believe the problem must be somewhere else.
Something is stopping the recovery boot. More research ahead.
When I find out more, will post here and give update.
Click to expand...
Click to collapse
Strange. You could try TWRP instead of CWM. I use TWRP and really like it:
Here is the download link for your device: http://www.techerrata.com/file/twrp2/hltetmo/openrecovery-twrp-2.7.2.0-hltetmo-4.4.img.tar
This is the Odin flashable recovery.
Here is TWRP page: http://teamw.in/project/twrp2/
EDIT: One more thing. Are these the exact steps you are following when booting into recovery?
"To access recovery mode on your Note 3, turn off the device and press Volume Up+Home+Power buttons at the same time for about 4-6 seconds. When the screen lights up and you see the Samsung logo, release the Power button but keep Volume Up+Home keys pressed until you see the recovery menu screen"
Cheers
Recovery Boot Loop Problem
andreiav said:
Strange. You could try TWRP instead of CWM. I use TWRP and really like it:
Here is the download link for your device: http://www.techerrata.com/file/twrp2/hltetmo/openrecovery-twrp-2.7.2.0-hltetmo-4.4.img.tar
This is the Odin flashable recovery.
Here is TWRP page: http://teamw.in/project/twrp2/
EDIT: One more thing. Are these the exact steps you are following when booting into recovery?
"To access recovery mode on your Note 3, turn off the device and press Volume Up+Home+Power buttons at the same time for about 4-6 seconds. When the screen lights up and you see the Samsung logo, release the Power button but keep Volume Up+Home keys pressed until you see the recovery menu screen"
Cheers
Click to expand...
Click to collapse
Yes, if I use the buttons, the download mode comes up saying 'Boot failed'. That's holding the vol. button 'up'. If I hold vol. down, it loads download mode correctly.
If I try to enter recovery thru Rom Manager, Recovery tries to start and the boot loop starts. ??
I may try TWRP. I've heard a lot about it.
Thanks for the links.
Recovery Boot Loop Problem
rspilot1 said:
Yes, if I use the buttons, the download mode comes up saying 'Boot failed'. That's holding the vol. button 'up'. If I hold vol. down, it loads download mode correctly.
If I try to enter recovery thru Rom Manager, Recovery tries to start and the boot loop starts. ??
I may try TWRP. I've heard a lot about it.
Thanks for the links.
Click to expand...
Click to collapse
Is changing over to TWRP as simple as installing CWM on Odin??
Just install and try?
rspilot1 said:
Is changing over to TWRP as simple as installing CWM on Odin??
Just install and try?
Click to expand...
Click to collapse
Yep. 5 minutes process at most
Sent from my GT-I9505
Recovery Boot Loop Problem
andreiav said:
Yep. 5 minutes process at most
Sent from my GT-I9505
Click to expand...
Click to collapse
Success!! TWRP works!!
Installed with Odin and it started up fine. Backed up system on my Ext. SD card and rebooted back to OS.
Perfect!
Don't know what happened to CWM but problem is solved thanks to your help.
If your ever in Winter Haven, Fl area, I'll buy you a steak dinner.
Thank you.
rspilot1 said:
Success!! TWRP works!!
Installed with Odin and it started up fine. Backed up system on my Ext. SD card and rebooted back to OS.
Perfect!
Don't know what happened to CWM but problem is solved thanks to your help.
If your ever in Winter Haven, Fl area, I'll buy you a steak dinner.
Thank you.
Click to expand...
Click to collapse
Awesome! Really glad it worked.
Cheers!
Sent from my GT-I9505

stuck in loop, possibly a different kind of loop

I was trying to fix my girlfriends nexus 5 that was doing the restart loop after an update. Everything seemed to go fine. Unlocked the bootloader, etc. Flashed the newest rom (6.0.1 (MMB29S) ce1d670f61061c3902f3997510ea55d7 6bfcdfa4f4840898e5d76fa044f5e6a0f71343bf) and then something obviously went wrong (not quite sure, dont think i touched anything) and it's now stuck in a different kind of loop that only loops while it's plugged in. Ive uploaded a video to youtube, but since im a new user i cant actually link it properly yet. Hopefully this wont annoy any mods, I promise it's not spam. youtube . be / yNSoiTPnGZw
Is there any way to get it to stay on for more than a couple seconds to retry the flashing?
Any help is appreciated.
atomkrieg said:
I was trying to fix my girlfriends nexus 5 that was doing the restart loop after an update. Everything seemed to go fine. Unlocked the bootloader, etc. Flashed the newest rom (6.0.1 (MMB29S) ce1d670f61061c3902f3997510ea55d7 6bfcdfa4f4840898e5d76fa044f5e6a0f71343bf) and then something obviously went wrong (not quite sure, dont think i touched anything) and it's now stuck in a different kind of loop that only loops while it's plugged in. Ive uploaded a video to youtube, but since im a new user i cant actually link it properly yet. Hopefully this wont annoy any mods, I promise it's not spam. youtube . be / yNSoiTPnGZw
Is there any way to get it to stay on for more than a couple seconds to retry the flashing?
Any help is appreciated.
Click to expand...
Click to collapse
What was your flashing procedure, did u is a toolkit or do it manually, can u get it into bootloader or recovery? What files did u is for update and where did u get them?
Sent from my XT1526 using Tapatalk
soupysoup said:
What was your flashing procedure, did u is a toolkit or do it manually, can u get it into bootloader or recovery? What files did u is for update and where did u get them?
Sent from my XT1526 using Tapatalk
Click to expand...
Click to collapse
First i followed the guide here on xda to unlock the bootloader(guide-nexus-5-how-to-unlock-bootloader-t2507905), installed twrp, which went fine. Then i realized that i couldnt (or didnt realize how to via command line) to copy the stock rom and install it via twrp, so then i followed this guide here on xda (tutorial-how-to-flash-factory-image-t2513701) with the factory img (6.01 hammerhead), got to this point in the guide: ★After everything finished, select "Recovery" using the volume buttons. then it stalled out,turned off and now just cycles on and offf through the google logo with the lock picture or if i hold down the volume button it will go into the bootloader briefly then restart, rinse repeat.
atomkrieg said:
First i followed the guide here on xda to unlock the bootloader(guide-nexus-5-how-to-unlock-bootloader-t2507905), installed twrp, which went fine. Then i realized that i couldnt (or didnt realize how to via command line) to copy the stock rom and install it via twrp, so then i followed this guide here on xda (tutorial-how-to-flash-factory-image-t2513701) with the factory img (6.01 hammerhead), got to this point in the guide: ★After everything finished, select "Recovery" using the volume buttons. then it stalled out,turned off and now just cycles on and offf through the google logo with the lock picture or if i hold down the volume button it will go into the bootloader briefly then restart, rinse repeat.
Click to expand...
Click to collapse
Have u tried messing with the power button, there are a lot of issues on the nexus 5 with the power button causing loops, simply from getting stuck, try playing with the power button a little and see of that helps, it might just need to be replaced
Wait, did u flash the factory img with twrp, or did u flash it using fastboot?
Sent from my XT1526 using Tapatalk
soupysoup said:
Have u tried messing with the power button, there are a lot of issues on the nexus 5 with the power button causing loops, simply from getting stuck, try playing with the power button a little and see of that helps, it might just need to be replaced
Wait, did u flash the factory img with twrp, or did u flash it using fastboot?
Sent from my XT1526 using Tapatalk
Click to expand...
Click to collapse
in the end fastboot, since i coulndt see how i could copy the img over to install via twrp
im pretty sure the button is fine, since it was cycling from the ota update install, then was working fine unlocking the bootloader, but after the flash, it crapped the bed.
Different problem
I had a problem where the google logo keeps on booting up with a slight vibration.This started to happen when my was dropped.I initially thought that was a software issue and thought of installing new ROM's but eventually my device was not detected :crying:
So i took it to repair shop near my house and they said it would cost 2500
I did some google research and found the reason was due to the power button being stucked during the fall.I got that repaired and my device is good to go
siddhu007 said:
I had a problem where the google logo keeps on booting up with a slight vibration.This started to happen when my was dropped.I initially thought that was a software issue and thought of installing new ROM's but eventually my device was not detected :crying:
So i took it to repair shop near my house and they said it would cost 2500
I did some google research and found the reason was due to the power button being stucked during the fall.I got that repaired and my device is good to go
Click to expand...
Click to collapse
ok, took it into a shop, got the power button fixed. It must have been on the way out because literally one minute it worked and the second it didnt. now i think ive got it narrowed down. it's saying it's unable to mount /persist. ive tried the various fixes:
e2fsck/dev/block/platform/msm_sdcc.1/by-name/persist
and
make_ext4fs/dev/block/platform/msm_sdcc.1/by-name/persist
but all i get is a not found error. not sure what to do from here on.
success!! i ended up stumbling on a bit how to restore the persist partition i didnt try. got a custom rom installs and everything works. thanks to everyone who tried to help!!
stuck in bootloop while flashing cataclysm rom
i tried to flash cataclysm rom in my n5..i unlock bootloader, flash custom recovery using TWRP and flash cataclysm rom following the instructions in this thread http://forum.xda-developers.com/goo...s-5-how-to-unlock-bootloader-t2507905...after that it was stuck in bootloop...i tried to open recovery but it wont open anymore it will only go back to loop....how can open the recovery? is it safe to flash CWM recovery?..tnx in advance..
When it was stuck in the loop, I had to hold vol up and down with the power button (wait a few secs until it was completely off) then reboot holding down + power till it opened the bootloader. if that doesnt work, try reflashing the bootloader via fastboot. I only found out i couldnt mount the persist partition by looking at the terminal window in twrp after trying to install a rom which kept it in the boot loop. I then used the cmd: make_ext4fs /dev/block/platform/msm_sdcc.1/by-name/persist to rebuild it.
jpau11 said:
i tried to flash cataclysm rom in my n5..i unlock bootloader, flash custom recovery using TWRP and flash cataclysm rom following the instructions in this thread http://forum.xda-developers.com/goo...s-5-how-to-unlock-bootloader-t2507905...after that it was stuck in bootloop...i tried to open recovery but it wont open anymore it will only go back to loop....how can open the recovery? is it safe to flash CWM recovery?..tnx in advance..
Click to expand...
Click to collapse
After flashing TWRP, use the volume and power button to select recovery. Once in TWRP, wipe cache, data, reboot.
audit13 said:
After flashing TWRP, use the volume and power button to select recovery. Once in TWRP, wipe cache, data, reboot.
Click to expand...
Click to collapse
problems solved!!i flashed TWRP again and it it already to the recovery so i reflashed the cataclysm rom and it worked...my n5 is now working..tnx guys!
jpau11 said:
problems solved!!i flashed TWRP again and it it already to the recovery so i reflashed the cataclysm rom and it worked...my n5 is now working..tnx guys!
Click to expand...
Click to collapse
Great to hear it. Congratulations:good:

Categories

Resources