Related
I just rooted my TF101 using ViperMod but now I'm not sure whether I should install CWM recovery or not if I want to install further OTAs. I have read some threads but couldn't come up with a clear answer. I read somewhere that only stock recovery can receive OTA updates but also read that CWM can receive them too. If I can't install CWM then what ROMs can I install with stock recovery? What's the best way to go if I want to be ready for the ICS? Thanks!!
theremix said:
I just rooted my TF101 using ViperMod but now I'm not sure whether I should install CWM recovery or not if I want to install further OTAs. I have read some threads but couldn't come up with a clear answer. I read somewhere that only stock recovery can receive OTA updates but also read that CWM can receive them too. If I can't install CWM then what ROMs can I install with stock recovery? What's the best way to go if I want to be ready for the ICS? Thanks!!
Click to expand...
Click to collapse
Technically you'll still receive the OTA update you just can't apply it if you have CWM or a custom ROM installed.
You can't install custom ROM without CWM (if you have an older SBK tablet you can use NVFlash with a compatible ROM).
So I shouldn't install cwm until the ICS drops right?
Sent from my Transformer TF101 using Tapatalk
If you want to update to ICS via OTA don't instal CWM.
As you have been told, you will get the OTA message but the update will fail.
So you have two choices (or three):
* Keep stock recovery and update to ICS when the OTA update is available
* Install CWM and update to ICS as soon as a DEV publishes an ICS ROM
* Install CWM and remove it as soon as you know the OTA is due (pretty lame, but you could do it).
Regards.
CalvinH said:
If you want to update to ICS via OTA don't instal CWM.
As you have been told, you will get the OTA message but the update will fail.
So you have two choices (or three):
* Keep stock recovery and update to ICS when the OTA update is available
* Install CWM and update to ICS as soon as a DEV publishes an ICS ROM
* Install CWM and remove it as soon as you know the OTA is due (pretty lame, but you could do it).
Regards.
Click to expand...
Click to collapse
Thanks, I think I'll just wait for the OTA as I want to update as soon as ICS drops in.
Sent from my PC36100 using Tapatalk
I have a question about removing CWR. Actually 2.
1. Can't we just uninstall and wipe data with Titanium since it was installed as an .apk- from Gnufabio? (pretty sure this won't work but thought I would throw it out there anyways). Where is the recovery located on a tablet (what folders) Same as in phones?
2. Can we just flash the stock recovery by itself and not reset back to .13 or younger? If I am running stock ROM, it seems that I should be able to just reflash the stock recovery and replace it w/o changing the ROM or factory reset.
I have no problem doing it the long way but if it doesn't need to be done and we can replace the CWR with stock and not tamper with the ROM, it seems logical.
Clearly I just got the tab recently and have been reading and reading but they seem so much different than the way phones work. I am very comfortable flashing ROMs/Kernels/Mods on phones, but just a little intimidated with the tablet (for now).
Woodrube said:
I have a question about removing CWR. Actually 2.
1. Can't we just uninstall and wipe data with Titanium since it was installed as an .apk- from Gnufabio? (pretty sure this won't work but thought I would throw it out there anyways). Where is the recovery located on a tablet (what folders) Same as in phones?
2. Can we just flash the stock recovery by itself and not reset back to .13 or younger? If I am running stock ROM, it seems that I should be able to just reflash the stock recovery and replace it w/o changing the ROM or factory reset.
I have no problem doing it the long way but if it doesn't need to be done and we can replace the CWR with stock and not tamper with the ROM, it seems logical.
Clearly I just got the tab recently and have been reading and reading but they seem so much different than the way phones work. I am very comfortable flashing ROMs/Kernels/Mods on phones, but just a little intimidated with the tablet (for now).
Click to expand...
Click to collapse
1- The RecoveryInstaller app only help to flash the recovery image so no you can just delete it.
2- You can flash a stock recovery image via CWM. You can get a repacked version here.
http://forum.xda-developers.com/showthread.php?t=1154947&highlight=unroot
baseballfanz said:
2- You can flash a stock recovery image via CWM. You can get a repacked version here.
http://forum.xda-developers.com/showthread.php?t=1154947&highlight=unroot
Click to expand...
Click to collapse
I figured that would be the case with the executable part of the apk.
I read that thread but wasn't sure if only the stock recovery by itself could be flashed w/o the prepacked ROM.
I decided to return to stock today so i could check out the newest ota which was not implemented in my fav rom yet. I soon realized its a pain in the ass to get there. Flash rom, update, update, etc, etc. And even worse is tracking down all the threads required for it.
Though I've narrowed it down to three or four, I thought i'd make a thread to put it all in one spot.
First off thanks to the members/devs that make these updates and roms for us. I dev on the HTC eVO 4g and know how time consuming and tedious it can be.
I am renaming and reuploading all the files required to ensure links stay current and are easy to follow. I will however be linking to all original threads where i got the files as well as giving props to the members who provided them.
I have a US version TF101 and will only be testing on that device. I dont know what works on tf101G, WW, TW models etc
I will update this thread as new rooted ota's come out.
ALL YOU NEED TO INSTALL IS A ALREADY ROOTED ASUS TRANSFORMER WITH A CUSTOM RECOVERY
THIS WILL NOT ROOT YOUR DEVICE, UN-ROOT YOUR DEVICE OR CHANGE YOUR CURRENT RECOVERY.
DONT FORGET TO BACK UP ALL YOURS APPS/DATA
FOR US VERSIONS ONLY
- STEP 1 - WIPE (DOWNLOAD) (This wipe zip was originally provided HERE by mike1986.
This script will erase and format your system and cache partition using EXT4 file-system ---Your external SD card and internal virtual SD card (/data/media) will remain untouched
- STEP 2 - FLASH STOCK ROOTED 9.2.1.11 FULL ROM AND REBOOT/SETUP (DOWNLOAD) originally provided here by MrNago
- STEP 3 - FLASH ROOTED OTA 9.2.1.17 AND REBOOT (DOWNLOAD) originally provided HERE by daoist
-STEP 4 - FLASH ROOTED OTA 9.2.1.21 AND REBOOT (DOWNLOAD) originally provided HERE by gee one
FOR WW VERSIONS ONLY
- STEP 1 - WIPE (DOWNLOAD) (This wipe zip was originally provided HERE by mike1986.
This script will erase and format your system and cache partition using EXT4 file-system ---Your external SD card and internal virtual SD card (/data/media) will remain untouched
- STEP 2 - FLASH STOCK ROOTED 9.2.1.11 FULL ROM AND REBOOT/SETUP (DOWNLOAD) originally provided here by MrNago
CANT FIND ROOTED VERSIONS OF THE NEXT FEW UPDATES THAT DONT REQUIRE ROOT KEEPER, SO IM STOPPING HERE. THIS WILL GET YOU STARTED THOUGH. i JUST DONT WANT TO BE RESPONSIBLE FOR NEWBS THAT CANT READ LOSING ROOT.
FAQ
-Will this root my transformer = no
-Will I lose root if i flash this = NO
-Can i flash this on top of a custom rom = NO
-Will this replace the custom recovery with the stock recovery? = NO, this will not touch your current recovery
-OMG, I lost root after this = NO you didnt or you did something wrong.
Can you explain why step 2 and 3 are needed?
You couldn't go from 1 to 4 if you want 9.2.1.21?
locutus7o9 said:
Can you explain why step 2 and 3 are needed?
You couldn't go from 1 to 4 if you want 9.2.1.21?
Click to expand...
Click to collapse
its my understanding that you have to have the last prior ota installed to be able to install the next. The last update may not include everything from the others.
Will this replace the custom recovery with the stock recovery?
xbs said:
Will this replace the custom recovery with the stock recovery?
Click to expand...
Click to collapse
I knew i'd forget one of the typicals in the FAQ..
Answer is no, this will not change/touch your current recovery
I wanted to return to stock Rom too, but I have seen your topic too late....
I first saved my root with rootsavekeeper
I have wiped cache and dalvik, and then install the rom
Now, I have a bootloop with the Asus logo, and if I try boot in recovery, I have the red robot
If u have a solution, I take it
Sorry for my english
jouix said:
I wanted to return to stock Rom too, but I have seen your topic too late....
I first saved my root with rootsavekeeper
I have wiped cache and dalvik, and then install the rom
Now, I have a bootloop with the Asus logo, and if I try boot in recovery, I have the red robot
If u have a solution, I take it
Sorry for my english
Click to expand...
Click to collapse
What ROM did you flash? If you flashed the official ROM from Asus you unrooted the TF.
Looks like you have stock recovery now.
Yes I have
My biggest problem is to get out on this sh*t Now
jouix said:
Yes I have
My biggest problem is to get out on this sh*t Now
Click to expand...
Click to collapse
Try this.
Hold Vol down plus power button
When you get the option of COld boot Linux or wipe data,
choose wipe data.
jouix said:
Yes I have
My biggest problem is to get out on this sh*t Now
Click to expand...
Click to collapse
What model do you have? B50, B60, B70?
If you have a B50 or B60, try this
Once you get back to stock honeycomb, you'll have to root it again.
@baseballfanz : Guy, you have saved my tablet .. I had almost throwed it in the garbage
@ldc2335 : I have bought it in France, and no idea about the version, sorry .. (I don't have the dock)
Well, now, I willl see if it is stable or not :
- if it is, I need to find the way to root it (but I have read it's not possible with the last Rom, right ?)
- if not ... I will try to return to Honeycomb and sell this piece of sh*t, and I will buy the Galaxy S3 or will wait for the Note 2
Thx again !!!!
I use NVflash way and from modded(rooted/CWM/Overclock) 9.2.1.17 directly flash back to stock clean 9.2.1.17 and it's very quick... and root it agan via Vipermod and flash 9.2.1.21 update zip.. Takes about lest than 30mins..
Thats one way to do it. I just dont wanna re-root etc.
Flash, reboot, flash, reboot, flash, reboot..done Definitly 30 mins or less.
jouix said:
@baseballfanz : Guy, you have saved my tablet .. I had almost throwed it in the garbage
@ldc2335 : I have bought it in France, and no idea about the version, sorry .. (I don't have the dock)
Well, now, I willl see if it is stable or not :
- if it is, I need to find the way to root it (but I have read it's not possible with the last Rom, right ?)
- if not ... I will try to return to Honeycomb and sell this piece of sh*t, and I will buy the Galaxy S3 or will wait for the Note 2
Thx again !!!!
Click to expand...
Click to collapse
If you can return to honeycomb, then just reroot and then flash any rom you want. Whats the issue?
Simple, clear, straightforward directions - very nice. The file naming is clever also, no "now which file do I flash next?..."
Does anyone have a clue where i can find cwm flashable WW Stock Roms with Original Recovery and no root?
Want to revert back to full basic!
(Tried to flash Stock Rom from Asus Website via CWM, didn't work...)
Try This
JohnMcLane said:
Does anyone have a clue where i can find cwm flashable WW Stock Roms with Original Recovery and no root?
Want to revert back to full basic!
(Tried to flash Stock Rom from Asus Website via CWM, didn't work...)
Click to expand...
Click to collapse
Try this
http://forum.xda-developers.com/showthread.php?t=1558170
i just used the search bar above, im sure theres more than this one.
You will also need a NVflashable tf101 with this....
I hve succesfully flashed the .11 version, but when I try to update to the next version, it restarts, and starts loading the installation as it is supposed to, ut then it says "installation aported"
I am using Rootkeeper and CWM, and have temp. unrooted, I am using a B70 WW.
Anyone have a solution?
Sumsar94 said:
I hve succesfully flashed the .11 version, but when I try to update to the next version, it restarts, and starts loading the installation as it is supposed to, ut then it says "installation aported"
I am using Rootkeeper and CWM, and have temp. unrooted, I am using a B70 WW.
Anyone have a solution?
Click to expand...
Click to collapse
Same here, its an assert issue, I remember dealing with it when flashing my epic touch and I believe that had to do with the version of CWM that it was being flashed from
can anyone confirm?
EDIT: B40 using roach v5.5.0.4 r2 CWM
Hey guys, I just unlocked and flashed ROM on my LG Optimus G phone and looking to do the same with the TFT300T.
I did read some of the stickies, and there are various ways of doing this.
Anyone recently unlock, root, and install ROM on your TF300T? Which directions did you take? I am looking for the simplest and user friendly solutions. Any tips are much appreciated.
Thanks
What rom/ android version are you currently running?
I am on 4.2.1
First off you need to go to Asus support site and download the v8 unlock apk & run it (unlocking your bootloader).
Then have a good read here to learn how to flash the compatible TWRP custom recovery (2.4.4.0), the root your device.
As of know I don't know about any custom roms that will boot with the newest bootloader. Correct me if I'm wrong here.
Do have a good read though, and read it again - and make sure you understand it and then read some again. Then proceed by following the steps to the letter.
Have fun! :good:
Can I just download an older unlock apk if the current ROMs don't run with the v8 unlock?
No. If you updated to 4.2.1 you need to use the v8 apk.
Ti2 said:
No. If you updated to 4.2.1 you need to use the v8 apk.
Click to expand...
Click to collapse
Got it. So if I am on 4.2.1, there's no ROM that I can flash? Just want to get that absolutely correct.
Not that I'm aware of at this point. The new bootloader uses a different partition layout than the "older" 4.1 ones, so it will soft brick (as will flashing the wrong recovery, you'll want the latest twrp 2.4.4.0)
Thanks. That's really good to know.
So at this point, for anyone on the OTA 4.2.1, we can unlock and root but cannot install any kernels or ROMs yet, correct? Anyone know if CleanROM is being updated to work for us yet?
I think you can try this ROM.
Thanks, I had a look at that. I'm having a hard time figuring out which set of "instructions" to use. The ones on the OP:
Code:
Installation instructions:
- Unlock your device using the Asus supplied APK. Search around the forum for the official unlocking app.
- Install a custom recovery such as TWRP. Follow the instructions in the TWRP thread (website)
- Copy over the ROM zip to your Internal Storage or your microsd card
- Boot into recovery and simply install the ROM. This ROM will NOT wipe your current ROM settings
- Enjoy!
Or at the bottom of post #3 (where it seems to have the download links) it says "BEFORE YOU DOWNLOAD AND INSTALL ANYTHING IN THE JB 4.2.1 folder BELOW CLICK THIS LINK FOR INSTRUCTIONS AND WARNINGS!"
Which then gives you this set of instructions:
Code:
The stock ROM is uploading in the JB 4.2.1 subfolder of the main download folder on the first page..
Be warned that once you do this... you will not be able to simply restore your backup and go back to 4.1.1. You will need to flash the JB bootloader ( think craig gomez has a package for it) and repartition your tablet. So be ready to STAY on 4.2.1
Instructions:
1. Make a full backup of your internal storage and copy it over to your computer after. Do a "nandroid" or "backup" in TWRP and copy the resulting folder/files to your computer (if you want a backup...)
2. Download and copy the Energy_JB_4.2.1_Partitions.zip to your tab.
3. Reboot into recovery and flash the above mentioned file. Reboot.
4. Wait while the blue line at the bottom is doing its thing. At the top you should see a "signature match" message. This WILL WIPE YOUR INTERNAL STORAGE. Which is why I recommend a backup!
5. At this point the tablet will NOT boot. You need to manually reboot and get back into recovery. Hold power and volume down and choose "RCK".
6. Either using an sdcard or adb, copy over the actual ROM zip Energy.TF201.JB.03.15.2013.STOCK.zip and flash it! Reboot... and... Enjoy.
Having started on the OTA 4.2.1, I can't figure out what I need to do here. Do I require the Partitions.zip, or am I already set with that having installed 4.2.1 prior? Conflicting sets of instructions are bad...
Silas0220 said:
So at this point, for anyone on the OTA 4.2.1, we can unlock and root but cannot install any kernels or ROMs yet, correct? Anyone know if CleanROM is being updated to work for us yet?
Click to expand...
Click to collapse
Sbdags is working on it and has made some great progress. He's got it figured out where we are gonna be able to flash the bootloader, kernel, and custom recovery all at one time. From what I've read, I have a feeling a release is coming pretty soon.
Just keep up with the thread and you'll be good to go.
Sent from my LG-LG855 using Xparent SkyBlue Tapatalk 2
That sounds great. It was so much easier flashing my LGOG phone.
Sent from my LG-E970 using xda app-developers app
Following
Im posting because I want to keep up on this thread, I too have an ASUS TF300 with 4.2.1 and want to root it and install a custom ROM like I have on my Droid Razr.
I tried several ROMs and this was the only one I was able to get to work.
glamisldy said:
Im posting because I want to keep up on this thread, I too have an ASUS TF300 with 4.2.1 and want to root it and install a custom ROM like I have on my Droid Razr.
Click to expand...
Click to collapse
You too huh?
I need to get my bootloader unlocked...
Yeah, more of the same for my TF300T...
Silas0220 said:
Having started on the OTA 4.2.1, I can't figure out what I need to do here. Do I require the Partitions.zip, or am I already set with that having installed 4.2.1 prior? Conflicting sets of instructions are bad...
Click to expand...
Click to collapse
I have been having lag issues since the OTA upgrade to 4.2.1 and figured putting a custom ROM on the TF300T might help things out. Glad I came in here. I had unlocked it via the ASUS website: http://www.service.asus.com/#!downloads/c1wax
So what else can u do with unlock?
Sent from my LG-E970 using xda app-developers app
I have flashed my phone a couple times with the leaks from here and now I am at the JB 4.1.2. but not with the premium suite. Is it possible to go back to factory and receive the official update from Verizon or is there a leaked build with the premium suite available. I have looked and not found any.
http://forum.xda-developers.com/showthread.php?t=2301814
I have used the nodata wipe versions of the build in the past using ODIN. Will that link work with it?
Thanks.
The link is to a full ROM you flash in recovery. So if you have root, unlocked the bootloader, and installed a custom recovery, you can flash the ROM in the link (and the firmware in post 2) and be on the latest official OTA.
If you are still stock and haven't got the latest OTA, you may just have to wait until it gets pushed to your device.
detonation said:
The link is to a full ROM you flash in recovery. So if you have root, unlocked the bootloader, and installed a custom recovery, you can flash the ROM in the link (and the firmware in post 2) and be on the latest official OTA.
If you are still stock and haven't got the latest OTA, you may just have to wait until it gets pushed to your device.
Click to expand...
Click to collapse
Pardon my ignorance, but can you point me to the instructions on how to use those 2 files. I have only done Odin before so that is why I am not too sure what I would do after downloading both zips and putting them on my SD card. Thank you!!
So you are rooted, with unlocked boot loader an custom recovery? Not sure by your post. I assume you are since asked about going back to take an ota.
Sent from my SCH-I535 using xda app-developers app
tu3218 said:
So you are rooted, with unlocked boot loader an custom recovery? Not sure by your post. I assume you are since asked about going back to take an ota.
Sent from my SCH-I535 using xda app-developers app
Click to expand...
Click to collapse
That is what I am not sure abaout. Each time I downloaded a link and installed it I used Odin v3.07 and also got firles(from xda) that had No Data wipe. SO if that means I am rooted, I am not sure. I have downloaded, then connect phone to Odin, install file and voila, it is back up. That is why I do not know. Thanks a million!
Please read forum rules before posting
Questions and help issues go in Q&A and Help sections
Thread moved
Thank you for your cooperation
Friendly Neighborhood Moderator
[email protected] said:
That is what I am not sure abaout. Each time I downloaded a link and installed it I used Odin v3.07 and also got firles(from xda) that had No Data wipe. SO if that means I am rooted, I am not sure. I have downloaded, then connect phone to Odin, install file and voila, it is back up. That is why I do not know. Thanks a million!
Click to expand...
Click to collapse
I would suggest you install ROM Manager. Once installed (it will only work if you have root), you can have it flash a custom recovery (Clockwork Mod" or "TWRP). You can then use the ROM manager to boot into the recovery you just flashed. Once in recovery you can flash those 2 zip files.
You would be well served to understand this a bit better but the ROM Manager will get you there with a minimum of knowledge. You can search here on XDA for instructions on flashing with CWM or TWRP, whichever you choose.
Good luck
sodium ampopto
junksecret said:
I would suggest you install ROM Manager. Once installed (it will only work if you have root), you can have it flash a custom recovery (Clockwork Mod" or "TWRP). You can then use the ROM manager to boot into the recovery you just flashed. Once in recovery you can flash those 2 zip files.
You would be well served to understand this a bit better but the ROM Manager will get you there with a minimum of knowledge. You can search here on XDA for instructions on flashing with CWM or TWRP, whichever you choose.
Good luck
Click to expand...
Click to collapse
I am trying to root the phone and it keeps telling me that there are no privileges???? I am trying to root and just cant get past that.
Go to the play store and download a root checker (there are several free ones) and it will tell you if you have root. If not, use one of the many guides to root. I suggest this one, follow this guide to root and install custom recovery Once you are rooted with a custom recovery you can flash the rooted version of the VRBLMD3 and the associated modem, RPM. etc.
http://forum.xda-developers.com/showthread.php?t=2046439
Hello community,
I was given the device last year and had been fairly satisfied with the performance of it. However, it has gotten laggy over the past couple weeks and a friend suggested to root and flash a rom on it. So, without any prior knowledge, I have been doing some research and browsing through the threads on this forum. I can see that there are guides but was very unsure if the methods would still work because I have noticed that most of them were last updated/edit a while ago. I know I shouldn't use the word 'latest' for doing this to a tablet that is fairly old in the market. However, it would be very helpful if someone can point me to some 'proven to work' or 'trust-worthy' guides of rooting, flashing recovery, and rom.
Also, just out of curiosity, please recommend which recovery and rom a first-timer should use if possible
try these roms.
rocketfans14 said:
Hello community,
I was given the device last year and had been fairly satisfied with the performance of it. However, it has gotten laggy over the past couple weeks and a friend suggested to root and flash a rom on it. So, without any prior knowledge, I have been doing some research and browsing through the threads on this forum. I can see that there are guides but was very unsure if the methods would still work because I have noticed that most of them were last updated/edit a while ago. I know I shouldn't use the word 'latest' for doing this to a tablet that is fairly old in the market. However, it would be very helpful if someone can point me to some 'proven to work' or 'trust-worthy' guides of rooting, flashing recovery, and rom.
Also, just out of curiosity, please recommend which recovery and rom a first-timer should use if possible
Click to expand...
Click to collapse
hello ,
these are the things you need to do before flashing a ROM.
note: -the following things may void your warranty.
-do this on your own risk.
1. HOW TO ROOT
-First install kingo root on your windows PC. Then check USB debugging .
( settings. < about device < touch build number 7times < go back and select developer options < check USB debugging.)
-Open kingo root on the PC and connect your device and connect your device to the PC. Start root and do not remove the USB cable until it says finish.
-Now you have successfully rooted your device.
2.HOW TO INSTALL A CUSTOM RECOVERY
- Go to the following link and download CLOCK WORK MOD(CWM)
LINK: https://www.clockworkmod.com/rommanager
Select your device and install the recovery.
go into the app and install recovery .
3.BACK UP
download rom manager from playstore and do a backup( do a backup using this ap only if you are using CWM recovery.
link for ROM manager: https://play.google.com/store/apps/d...mmanager&hl=en
Now the first thing you need to do is download this rom.
https://www.androidfilehost.com/?fid=95916177934533333
(note: you can flash the rom of p5110 for p5113)
now to flash the rom follow the following steps.
1. Go to recovery mode
2. (have the rom in your sd card)flash it there .
use this link to know how to flash a rom.
https://www.youtube.com/watch?v=tJfPwWjnWGY
now you can reboot after flashing.
to get inbuilt google apps and play store you need to install something called GAPPS (Google apps) download from this link.
http://opengapps.org/?api=5.1&variant=nano
now you flash this zip the same way you flashed the rom.
any problems plz notoce me.
Zte blade l said:
hello ,
these are the things you need to do before flashing a ROM.
note: -the following things may void your warranty.
-do this on your own risk.
1. HOW TO ROOT
-First install kingo root on your windows PC. Then check USB debugging .
( settings. < about device < touch build number 7times < go back and select developer options < check USB debugging.)
-Open kingo root on the PC and connect your device and connect your device to the PC. Start root and do not remove the USB cable until it says finish.
-Now you have successfully rooted your device.
2.HOW TO INSTALL A CUSTOM RECOVERY
- Go to the following link and download CLOCK WORK MOD(CWM)
LINK: https://www.clockworkmod.com/rommanager
Select your device and install the recovery.
go into the app and install recovery .
3.BACK UP
download rom manager from playstore and do a backup( do a backup using this ap only if you are using CWM recovery.
link for ROM manager: https://play.google.com/store/apps/d...mmanager&hl=en
Now the first thing you need to do is download this rom.
https://www.androidfilehost.com/?fid=95916177934533333
(note: you can flash the rom of p5110 for p5113)
now to flash the rom follow the following steps.
1. Go to recovery mode
2. (have the rom in your sd card)flash it there .
use this link to know how to flash a rom.
https://www.youtube.com/watch?v=tJfPwWjnWGY
now you can reboot after flashing.
to get inbuilt google apps and play store you need to install something called GAPPS (Google apps) download from this link.
http://opengapps.org/?api=5.1&variant=nano
now you flash this zip the same way you flashed the rom.
any problems plz notoce me.
Click to expand...
Click to collapse
I was looking in the forum and someone said that I would also need to unlock the bootloader? If so, how do I do that?
Also, is there a difference between kingroot and towelroot? I saw a post in the forum here saying towelroot is fast and easy to root the tablet.
Not much difference.
Actually there is not much difference between kings root and towel root....towel root doesn't need a PC...but I have never used it so I can't assure you that it is safe.
And coming to the boot loader I don't know much about it but I didn't do anything like that before flashing a rom or rooting my tab2....
If you want further assistance about the boot loader I can help you with that..
rocketfans14 said:
I was looking in the forum and someone said that I would also need to unlock the bootloader? If so, how do I do that?
Also, is there a difference between kingroot and towelroot? I saw a post in the forum here saying towelroot is fast and easy to root the tablet.
Click to expand...
Click to collapse
it is not necessary to unloack bootloader for tab 2 as it comes with a unlocked bootloader from stock.
Zte blade l said:
Actually there is not much difference between kings root and towel root....towel root doesn't need a PC...but I have never used it so I can't assure you that it is safe.
And coming to the boot loader I don't know much about it but I didn't do anything like that before flashing a rom or rooting my tab2....
If you want further assistance about the boot loader I can help you with that..
Click to expand...
Click to collapse
Hey, it's been a while. Honestly speaking, when I first posted this thread, I didn't really have enough time to do the things so now I am finally back and trying to do it. So far, I know what recovery and rom I'm going to use with all the files downloaded and ready. Though, currently, I am still at the pre-root stage. I have read up things about kingoroot and not sure if I wanted to use it. So I looked around on the forum and wonder if Odin is still a working solution. Reading on the steps and guides, I was wondering if I need to have Kies installed?
rocketfans14 said:
Hey, it's been a while. Honestly speaking, when I first posted this thread, I didn't really have enough time to do the things so now I am finally back and trying to do it. So far, I know what recovery and rom I'm going to use with all the files downloaded and ready. Though, currently, I am still at the pre-root stage. I have read up things about kingoroot and not sure if I wanted to use it. So I looked around on the forum and wonder if Odin is still a working solution. Reading on the steps and guides, I was wondering if I need to have Kies installed?
Click to expand...
Click to collapse
Kies is not needed as it never helped.
You can depend on odin it is your only saviour when you are in trouble.
I think rooting with kingroot is easy as it is just connecting to your PC and cick the start button.
So just notice me when your ready.
And there is also one good news...?
Tab 2 has got marshmallow.
Zte blade l said:
Kies is not needed as it never helped.
You can depend on odin it is your only saviour when you are in trouble.
I think rooting with kingroot is easy as it is just connecting to your PC and cick the start button.
So just notice me when your ready.
And there is also one good news...��
Tab 2 has got marshmallow.
Click to expand...
Click to collapse
I have rooted the tablet. I did it with odin and twrp with flashing the updatedSuperSU zip folder.
I have tried flashing the CM12.1 rom yesterday but resulted in a boot loop. So for now, I'm just rooted and on stock rom until I or someone can find out what was the problem. I have read about the discussion with marshmallow but it seems to me that the project isn't really stable yet. From what I have researched lately, can I assume there's issue with the p51xx line of tablets? Because I saw many people having problems with p51xx and most people with the other tablets aren't having any.
rocketfans14 said:
I have rooted the tablet. I did it with odin and twrp with flashing the updatedSuperSU zip folder.
I have tried flashing the CM12.1 rom yesterday but resulted in a boot loop. So for now, I'm just rooted and on stock rom until I or someone can find out what was the problem. I have read about the discussion with marshmallow but it seems to me that the project isn't really stable yet. From what I have researched lately, can I assume there's issue with the p51xx line of tablets? Because I saw many people having problems with p51xx and most people with the other tablets aren't having any.
Click to expand...
Click to collapse
You first must update your tab to jelly bean bootloader, before trying out newer roms.
Or perhaps flash stock jb firmware with odin
Whatever you choose, both is ok.
http://forum.xda-developers.com/showthread.php?t=2642005
Read here
The first thing you do, is take a nandroid backup, it's very important at every step, unless you are really ready to risk. It's better to have it.
Next Read through the rom threads, clear your mind and your tab too. You must format data.
Stay on twrp 2.8.7.2. Don't go to the latest one yet.
Flash rom, wait, it will boot up.
Every tab behave differently with every rom, sure you are going to face soft reboots, on some roms it will be a lot, on some it will be less. I would suggest you try both LP and kk first.
Remember, it's better to keep this tab updated than to stay on stock. This tab 2 series has a emmc bug and staying on stock or jumping back is a risk too. I have been on kk and lp. They both have kept this tab running great and away from that bug.
billysam said:
You first must update your tab to jelly bean bootloader, before trying out newer roms.
Or perhaps flash stock jb firmware with odin
Whatever you choose, both is ok.
http://forum.xda-developers.com/showthread.php?t=2642005
Read here
The first thing you do, is take a nandroid backup, it's very important at every step, unless you are really ready to risk. It's better to have it.
Next Read through the rom threads, clear your mind and your tab too. You must format data.
Stay on twrp 2.8.7.2. Don't go to the latest one yet.
Flash rom, wait, it will boot up.
Every tab behave differently with every rom, sure you are going to face soft reboots, on some roms it will be a lot, on some it will be less. I would suggest you try both LP and kk first.
Remember, it's better to keep this tab updated than to stay on stock. This tab 2 series has a emmc bug and staying on stock or jumping back is a risk too. I have been on kk and lp. They both have kept this tab running great and away from that bug.
Click to expand...
Click to collapse
Do I have to unroot first? Do you have a link to making a nandroid backup?
Edit: Oh, I looked at the link you included and it said that if I am on stock jb (4.2.2), I can skip the update bootloader part..
When you flashed the new rom, did you do a factory reset (wipe data)?
Sent from my SAMSUNG-SM-G870A using XDA Free mobile app
rocketfans14 said:
Do I have to unroot first? Do you have a link to making a nandroid backup?
Edit: Oh, I looked at the link you included and it said that if I am on stock jb (4.2.2), I can skip the update bootloader part..
Click to expand...
Click to collapse
Yes, that's what I meant too, if you're on jb already, you are fine. You don't have to unroot. For making a nandroid backup, use twrp recovery, there is an option for backup, select and backup all from there, if you get into bootloop or any other problem, as long as you can get back to recovery, you can restore from there. Most rom comes pre rooted.
rocketfans14 said:
I have rooted the tablet. I did it with odin and twrp with flashing the updatedSuperSU zip folder.
I have tried flashing the CM12.1 rom yesterday but resulted in a boot loop. So for now, I'm just rooted and on stock rom until I or someone can find out what was the problem. I have read about the discussion with marshmallow but it seems to me that the project isn't really stable yet. From what I have researched lately, can I assume there's issue with the p51xx line of tablets? Because I saw many people having problems with p51xx and most people with the other tablets aren't having any.
Click to expand...
Click to collapse
Did you clear dalvik cache in recovery before flashing rom?
Zte blade l said:
Did you clear dalvik cache in recovery before flashing rom?
Click to expand...
Click to collapse
Yes, I cleared the top four options in recovery, and formatted data before flashing.
billysam said:
Yes, that's what I meant too, if you're on jb already, you are fine. You don't have to unroot. For making a nandroid backup, use twrp recovery, there is an option for backup, select and backup all from there, if you get into bootloop or any other problem, as long as you can get back to recovery, you can restore from there. Most rom comes pre rooted.
Click to expand...
Click to collapse
That's what I did. Let me just briefly summarize what I have done:
used odin with twrp
booted into recovery and made back up
cleared dalvik, cache, system, and data, formatted data
flashed update supersu, booted into system and checked root with root checker
rebooted into recovery, cleared dalvik, cache, system, and data, formatted data again
flashed cm12.1 and gapps, rebooted but ran into bootloop at splash screen
rebooted into recovery and restored back up
So I'm rooted and on stock 4.2.2 currently.
champ1919 said:
When you flashed the new rom, did you do a factory reset (wipe data)?
Sent from my SAMSUNG-SM-G870A using XDA Free mobile app
Click to expand...
Click to collapse
I did.
Try flashing blisspop or slimLP.