I have a 727r and I want to use it on wind, and have no idea what combo of rom / kernal / modem to use. what I do know:
The 727r radio has the ability to pick up the signal
The wind network uses HSPA+ - transmit on 1700, receive on 2100
There are modem files out there for these frequencies
Things I don't know
How to make sure a rom / kernel / radio will work with each other (hopefully without needing to spend hours flashing n! combinations)
How to figure out if a modem file will support my device, or the frequencies I need
Things I've tried
the 989 from Tmobile runs on HSPA+, so I tried installing a tmobo rom, kernel, and radio with little success.
Trying to install / flash different rom - kernel - modem combos (most of which results in baseband version:unknown - this means the modem and rom are incompatible right?)
What I'm asking
Is there anyone running a 727r on wind that wouldn't mind sharing their rom / kernel / modem combo?
Has anyone found a Cyanogen-kernel-modem combo that works?
I am NOT asking which is the "best". After spending 4 hours of flashing and praying things will work, I don't care if I get the "worst" rom. I just want a combo that works
WORKING(more or less) COMBOS:
R34P3ReX_T989_Skyrocket_Conversion - Juggernaut_50_0218 - Tmo_SGH-T989_KID_radio
Gingerbread base, gyroscope tilts screen wrong way, a bit buggy, but works
CM10, CM10, T989UVLH1
Works well enough, having Call issues though. Going to try a new radio
Cyanogen always gets terrible battery. Going to look for an optimized version but not a problem for me
CM10, Blaze 4G UVLH5
Calling worked, I could hear caller, but they heard a lot of garbled blarky. Not good
u don't need a specific ROM or kernel at all, all u need to do is try different t radios. try the uvle1 from the t989 aka Hercules subsection, and give the modem someone dumped from the i757m bell version to see if u can catch a signal. I strongly believe the later will work
pileot said:
I have a 727r and I want to use it on wind, and have no idea what combo of rom / kernal / modem to use. what I do know:
The 727r radio has the ability to pick up the signal
The wind network uses HSPA+ - transmit on 1700, receive on 2100
There are modem files out there for these frequencies
Things I don't know
How to make sure a rom / kernel / radio will work with each other (hopefully without needing to spend hours flashing n! combinations)
How to figure out if a modem file will support my device, or the frequencies I need
Things I've tried
the 989 from Tmobile runs on HSPA+, so I tried installing a tmobo rom, kernel, and radio with little success.
Trying to install / flash different rom - kernel - modem combos (most of which results in baseband version:unknown - this means the modem and rom are incompatible right?)
What I'm asking
Is there anyone running a 727r on wind that wouldn't mind sharing their rom / kernel / modem combo?
Has anyone found a Cyanogen-kernel-modem combo that works?
I am NOT asking which is the "best". After spending 4 hours of flashing and praying things will work, I don't care if I get the "worst" rom. I just want a combo that works
Click to expand...
Click to collapse
So.. im using the Tmo Radio.. the latests and you can get it here: http://forum.xda-developers.com/showthread.php?t=1895400
and as for the ROM i am using Cyanogenmod 10.0 but the T989 version.
works good.. dont forget to wipe everything.. as for the other comment where you just need to flash the radio.. dunno.. i tried that a couple of times and it didnt work.. however.. im about to try it again.. so ill let you know how it goes.. for now though.. just to get it working.. i would do the above..
tip: i initially flashed the UVLH1 radio.. worked great.. great signal.. then i updated the other day to the latest.. and it seems as though my signal is not as strong.. dunno.. but try it out.. you never know..
also.. on initial boot up.. you need to give it a couple of minutes for things to settle.. it should pick up the Wind signal by itself... if it doesnt after 5 mins.. then do a search.. but you shouldnt have a problem..
So.. i can confirm that you CAN install the TMO radio and the ATT Skyrocket CM 10 ROM!!!!!
Infact... it works great!!!
TIP: i can also confirm that the UVLH1 has a stronger signal than the UVLI4 radio which is the latest. not sure why.. but i reverted back to UVLH1
hope this helps!
df186 said:
So.. i can confirm that you CAN install the TMO radio and the ATT Skyrocket CM 10 ROM!!!!!
Infact... it works great!!!
TIP: i can also confirm that the UVLH1 has a stronger signal than the UVLI4 radio which is the latest. not sure why.. but i reverted back to UVLH1
hope this helps!
Click to expand...
Click to collapse
I have ROGERS_ICS_ULFX3 stock rom installed, baseband T989UVLH1, I flashed it and i get no sim error
Just before this on Stock gingerbread i had gotten it to work, but after 1 restart, everything got screwed up
Help me
I have been running SkyJB 4.1.2, and Blaze LB7 in Southern Ontario, picking up Wind signals. Speeds are okay, still trying to find the best combo, but that combo works.
kr4tos said:
I have ROGERS_ICS_ULFX3 stock rom installed, baseband T989UVLH1, I flashed it and i get no sim error
Just before this on Stock gingerbread i had gotten it to work, but after 1 restart, everything got screwed up
Help me
Click to expand...
Click to collapse
flash the radio twice,no cable plugged in before flashing rom, might help
df186 said:
So.. im using the Tmo Radio.. the latests and you can get it here: http://forum.xda-developers.com/showthread.php?t=1895400
and as for the ROM i am using Cyanogenmod 10.0 but the T989 version.
works good.. dont forget to wipe everything.. as for the other comment where you just need to flash the radio.. dunno.. i tried that a couple of times and it didnt work.. however.. im about to try it again.. so ill let you know how it goes.. for now though.. just to get it working.. i would do the above..
tip: i initially flashed the UVLH1 radio.. worked great.. great signal.. then i updated the other day to the latest.. and it seems as though my signal is not as strong.. dunno.. but try it out.. you never know..
also.. on initial boot up.. you need to give it a couple of minutes for things to settle.. it should pick up the Wind signal by itself... if it doesnt after 5 mins.. then do a search.. but you shouldnt have a problem..
Click to expand...
Click to collapse
I tried to install the T989 (Hercules) CM10 version but it kept failing to install
The recovery I'm using is Team Win Recovery, if that matters. I suspect either TWRP is not working or the Kernel is incompatible
What Kernel are you using?
pileot said:
I tried to install the T989 (Hercules) CM10 version but it kept failing to install
The recovery I'm using is Team Win Recovery, if that matters. I suspect either TWRP is not working or the Kernel is incompatible
What Kernel are you using?
Click to expand...
Click to collapse
if it was built for t989 specific phones it wont install because of the assert
u dont need a t989 rom anyways, but if you want to try them out make sure the updater script doesnt have the assert function and do the rotation fix
I'm using the i727r (Rogers) running CM 10.1. I'm still on Rogers using the stock radio for now. Is there any consensus as to which radio file to flash for best results?
I know this thread is a little stale, but I figured I would throw in my two cents.
I have an i727r, unlocked. Right now I am running PACman Rom (http://forum.xda-developers.com/showthread.php?t=2178402) with the Blaze LB7 radio (4th from the bottom here: http://forum.xda-developers.com/showthread.php?t=1895400). They said I shouldn't be able to run an ICS radio with a JB Rom, but somehow it seems to be working. Note that the radio was on there before flashing PACman.
The kernel showing up in my phone info is the one that came with the PACman Rom, 3.0.72-cyanogenmod. I know this because before flashing PACman over stock, the kernel was 3.0.8.
Having said all that I'm thinking about updating my radio, probably to UVMB1. I'm not sure if I should bother though. I have a Nexus S, which is designed as an AWS phone out of the factory, and when I put my SIM card in that phone, the speedtest results are the same as what I'm getting right now with the LB7 radio on the Skyrocket. So I'm not sure I'd gain much by updating. :/
Can some people in the GTA please chime in to help me.
I am using a Rogers Skyrocket.
SlimBean Rom 4.2.2 Official 7
T989UVMC6 radio/modem
I tried a few other modems and found this one to be the most stable as some did not even allow a call to be made.
This is what I noticed.
Full charge I talked for 20 minutes and lost 10% battery (from full charge)
I get erratic data speeds inside=500-1 and outside I get 3
The problem is the battery drain and signal strength.
What are you using and what is your battery life and signal strength?
Data speeds?
your location?
droiduzr2 said:
Can some people in the GTA please chime in to help me.
I am using a Rogers Skyrocket.
SlimBean Rom 4.2.2 Official 7
T989UVMC6 radio/modem
I tried a few other modems and found this one to be the most stable as some did not even allow a call to be made.
This is what I noticed.
Full charge I talked for 20 minutes and lost 10% battery (from full charge)
I get erratic data speeds inside=500-1 and outside I get 3
The problem is the battery drain and signal strength.
What are you using and what is your battery life and signal strength?
Data speeds?
your location?
Click to expand...
Click to collapse
My carrier is videotron, one of the most difficult carriers to get unlocked phones to work on. Here's what works for me, sim unlocked, rooted. Running cyanogenmod 10.1.0 RC2 with Blaze 4G LF4 radio, nobars battery saver and network booster. I'm still have the same issue as everyone else, baseband unknown and network type unknown. I've been running the stock kernel and I've been running like this for the past couple days, and touch wood, I haven't had any issues. I've tried the 2 Tmo radios, I got no signal what-so-ever, the telus radio kept dropping my connection, meaning, I would have to try and resend text messages several times before it would actually send. Now that I'm using my current setup, as described at the beginning of my post, no problems to date.
I hope my input helps out.
wraith79 said:
My carrier is videotron, one of the most difficult carriers to get unlocked phones to work on. Here's what works for me, sim unlocked, rooted. Running cyanogenmod 10.1.0 RC2 with Blaze 4G LF4 radio, nobars battery saver and network booster. I'm still have the same issue as everyone else, baseband unknown and network type unknown. I've been running the stock kernel and I've been running like this for the past couple days, and touch wood, I haven't had any issues. I've tried the 2 Tmo radios, I got no signal what-so-ever, the telus radio kept dropping my connection, meaning, I would have to try and resend text messages several times before it would actually send. Now that I'm using my current setup, as described at the beginning of my post, no problems to date.
I hope my input helps out.
Click to expand...
Click to collapse
Ur input doesn't really help... 10.1 REQUIRES ucmc1 or ruxau7 , neither of which ur using. Try one of those radios and then post results
Edited: UVMB1 as well
icenight89 said:
Ur input doesn't really help... 10.1 REQUIRES ucmc1 or ruxau7 , neither of which ur using. Try one of those radios and then post results
Click to expand...
Click to collapse
Well, if it NEEDS ucmc1 or ruxau7, why have I been running this setup for the past month with no issues!?
wraith79 said:
Well, if it NEEDS ucmc1 or ruxau7, why have I been running this setup for the past month with no issues!?
Click to expand...
Click to collapse
You will, or already have had issues you're not aware of.
Sent from my SAMSUNG-SGH-I727 using Tapatalk 4
wraith79 said:
Well, if it NEEDS ucmc1 or ruxau7, why have I been running this setup for the past month with no issues!?
Click to expand...
Click to collapse
Edited, UVMB1, the NEW Blaze 4G radio from this thread seems to work as well:
http://forum.xda-developers.com/showthread.php?t=1895400
But like x said, u had issues u just weren't aware of them. Problems don't just APPEAR for no reason.
this threads getting confusing.
ucmc1 and uxuma7 is for rogers and att users on cm10.1
if using unlocked skyrocket for other carriers then you would need compatible jb radio for the new/unlocked carrier for cm10.1 based roms
so for tmo/wind etc you would need UVMB1 for the AWS bands, there are other jb radios for telus, bell but don't know if/how well they work on said carrier.
so if your carrier uses the same frequency's as tmo then UVMB1 seems to be what users are reporting success with.
if your carrier is using same frequency as att/rogers then the ucmc1 or uxuma7 radio is what you need
correct me if im wrong
^^^ this is exactly what I said except in a more detailed explanation .
icenight89 said:
^^^ this is exactly what I said except in a more detailed explanation .
Click to expand...
Click to collapse
good, i just needed a confirmation so i can add that info and a link to this post in the radio section of the 1stop sticky
Hi guys,
Do any of you know if the Desire s supports the 5ghz wifi band? I have just got a new router from Virgin and it has the 2.4 and 5 ghz bands available but my phone doesn't see the SSID for 5 ghz. I know it is 8011.2 n, which is supposed to support 5 ghz, but no joy. Do you think i need a firmware update or it's just not enabled on this phone??
Thanks for any tips!!!
matty pompy99 said:
Hi guys,
Do any of you know if the Desire s supports the 5ghz wifi band? I have just got a new router from Virgin and it has the 2.4 and 5 ghz bands available but my phone doesn't see the SSID for 5 ghz. I know it is 8011.2 n, which is supposed to support 5 ghz, but no joy. Do you think i need a firmware update or it's just not enabled on this phone??
Thanks for any tips!!!
Click to expand...
Click to collapse
What firmware do you have, which radio? (last official update or have you flashed the 4.0 ruu)
"The difference between pornography and erotica is lighting."
- Gloria Leonard
Just tried, able to connect using at freq 5gh.
Why not set the router's freq to auto?
FromBeyondThisWorld
I'm using endymion 2.1 rom, stock radio I believe. The router is set to auto for the 5 gig band, strange.
Any ROM/ Radio recommendations??
Cheers Guys.:cyclops:
matty pompy99 said:
I'm using endymion 2.1 rom, stock radio I believe. The router is set to auto for the 5 gig band, strange.
Any ROM/ Radio recommendations??
Cheers Guys.:cyclops:
Click to expand...
Click to collapse
If your s-off then i would recommend the radio and framework from the ics wwe ruu, there's a link and instructions in the index thread I had great improvements to wifi and signal after flashing this.
"I'm living so far beyond my income that we may almost be said to be living apart."
- E E Cummings (1894-1962)
Yes I'm s-offed, thanks buddy for the tip.......
Hi. I run into some problems. Basically 3G network stop working after installing pac_urushi_4.4.4.Beta-1.0_20140803-210807.
Cannot connect to 3G network and obviously cannot have 3Gdata transfer. Everything else is working great.
I also tried with SuperJellyBean8 and the same happens. Any idea?
I'm running
PAC 4.4.4.Beta-1.0
AOKP urushi_kikat
Android 4.4.4
kernel 3.4.0-LX+
Over Xperia RAY ST18i
The HSDPA (3G) frequency is 2100 MHz
UMTS-GSM (2G) frequency is 1800 MHz
some one else is experimenting the same issue?
First try uninstalling and re-installing the app. If you face that problem again then verify mod apk. I think its may be due to apk you are using.
AndroCID said:
First try uninstalling and re-installing the app. If you face that problem again then verify mod apk. I think its may be due to apk you are using.
Click to expand...
Click to collapse
I did that several times. I also installed a previous version of the rom, and the stable 4.3 version, with the respective image.img for each rom.
Could be something broken (hardware) in the phone becouse of the rom actualization?
some one had the same problem after installing a rom?