Phone will not boot into recovery but does boot into download mode - Verizon Samsung Galaxy S III

My phone is rooted with stock rom. The only changes are listed below
Froze bloat that was safe
changed bootanimation to stock samsung
replaced some apps with inverted versions of themselves (ex. google +, stock messaging)
Here goes:
I was using navigation and I noticed that my phone was off after I had finished. Nothing worked at all, I could not boot into recovery or download. I connected the phone to a charger and red led flashes and an empty battery appears. The battery was full. I could reboot the phone while on the charger, but it would shut off as soon as it got to the homescreen. While off, If I pressed the home button, the green battery would appear as if it were charging. From here I could boot into recovery and download mode. The phone will only boot into these modes while connected to the charger. Here is where it went bad. I attempted to restore a backup while the phone was on the car charger and my car charger got pulled out in the middle of a restore. No charger meant that the phone shut off mid restore. Now, when I plug in the phone, the red led appears and the empty battery with a circle inside appears and then goes away. This repeats itself over and over and the phone buzzes when the empty battery reappears. I can still boot into download mode but not recovery. If I try to flash the stock samsung rom via odin, it says that it passes, however upon automatic reboot the samsung appears and nothing else. After the samsung appears the phone just continues to buzz every 5 seconds or so as if it is trying to do something. Could it be a bootloop? I have done a ton of searching here and now I am resorting to help! Your time is appreciated and beers on me if you can help me get my phone back to normal.

try:
Section 6: Using Odin to flash back to Stock from any rom/ recover from a soft brick
*Move everything you dont want to lose from internal sdcard to external sdcard as this will reformat your internal sdcard!!
Step 1: Download and install these files to pc:
Odin- http://samsung-updates.com/Odin307.zip
Samsung Driver- http://tinyw.in/Fdoz
Step 2: Download one of these Factory STOCK Bloated 4.0.4 roms and the stock kernel to your pc:
*You will need to unzip these files with a .zip program such as 7zip to extract the .tar files!
VRALG1- http://goo.im/devs/invisiblek/i535/C...w_ship.tar.zip(Yes this works with the stock VRALF2 kernel!)
VRALF2- http://goo.im/devs/invisiblek/i535/H...w_ship.tar.md5
Rooted Stock VRALF2 by MrRobinson(aka root66)- Here is the Torrent link
Stock VRALF2 Kernel- http://samsung-updates.com/kernel/Sa...LF2_Kernel.zip
Step 3: Power device off, then hold the volume down/home/power keys until you see a yellow triangle, then press the volume up key to access "download mode"
Step 4: Open Odin and connect the oem usb cable to pc & device, you should see a "comport #" in upper left hand corner of odin
Step 5: Uncheck auto reboot
Step 6: Click on the PDA function of odin and select the Stock Kernel you downloaded in step 2. Should take roughly 1 min, then odin will say pass/reset
Step 7: Click on the PDA function of odin and select the Stock Rom you downloaded in step 2. Should take less than 8 minutes, then odin will say pass/reset
Step 7: Disconnect usb cable, then pull and reinsert the battery
Step 8: Press and hold the volume up/home/power keys until you see a green android, you should boot into stock recovery
Step 9: Wipe data/factory reset
Step 10: Reboot! (You should now be booted into factory stock, locked, and bloated ICS 4.0.4)
*If your internal memory(EMMC) has corrupted data partitions and my method above wont recovery your device, try this: http://forum.xda-developers.com/show...4#post30477064
And thank DroidStyle for providing this ^^

I will try your method. I believe I have completed these steps but I will try again. The link you supplied is not found.

Should the stock rom file be a .tar or .tar.md5? The kernel was a .tar and I have an official samsung vralf2 that is a .tar.md5

I tried your method and the empty battery is gone , but it doesnt get past the samsung on booting into recovery and continues to buzz every few seconds with a blank screen.

For some reason the phone will not recognize the battery. I tried a new one at verizon and the same thing. I can now boot into both recovery and download mode when connected to the charger , but the phone shuts off as soon as it boots and shows an empty battery with a circle in the middle. Sometimes it does not make it through the verizon boot animation and sometimes it makes it all the way to the homescreen and I can make a few selections before it turns off. After flashing the stock kernel and rom in odin I believe i am completely stock, however I do not want to chance sending the phone into Verizon. I believe that I saw a thread before this happened to me talking about having to calibrate the battery in some way and it had an item to flash in order to fix the problem. I can not find it now. Any ideas? Now that I can access recovery is there anything else that can be done? Why won't the phone recognize that it has a battery? As soon as I pull it off the charger it shuts off. When it is on the charger it appears to be charging and the green in the battery appears to be at about 80% but the level does not move up or down at all. Thank you for your help ahead of time.

I replied to your other thread seems to have been deleted.----- Boot into download mode and let it sit on the charger for 30 minutes, remove from charger pull and reinsert battery. Boot your phone regularly. Charge/profit
Sent from my VzW Galaxy s3 using xda premium

Ok i am in the process right now. Thank you, and I hope this works. If it does not and If i try to download bootchains , kernel, modem , and stock rom once again, is there any particular order that this should be done in? Also, is there any way that I can get cwm recovery on my phone? I can not get my computer to recognize the phone in download mode or recovery mode to push it with adb. If I could get cwm on the phone would wiping battery stats and fixing permissions do anything?

Related

Unbricking help

I tried to put in the mod for the circle battery and the evo black bar on top of just having the circle battery in already.. minus the black bar mod. I went to update it from recovery mode, it turns on with the ATT and the Galaxy S screen... then just goes black. Not sure what to really do about this other then messing with any more mods after this.
I tried Recovery Mode and deleting everything and then rebooting it... it did nothing.
this happened to me too... 3 times actually.
Not really sure what causes the problem, but at this point you're gonna have to reflash the firmware. Use the Odin oneclick downloader to reflash to stock, then odin v1.0 to flash to what ever firmware you had on before.
In order to do this, you have to put your phone into recovery mode. First open up odin one click downloader. Next, hold the volume up and down button (if your on the i9000 firmware, just hold down the down volume button) and insert the usb. after a few seconds, a new screen should pop up saying it's in download mode. (the screen should say "download, do not turn off target!!!") then hit start on odin.
When you do the black bar/battery update, make sure you re-download it, put it into your sdcard, then rename it. DO NOT reinstall an update that you've already installed. this will also screw up the firmware.
download mode was a bit trickery for me to get into.....
here are my steps...
Open Odin3 and get the pit file and pda tar file inputted.
then plug your phone into usb.
turn on the phone to just the charging graphic...
from there hold the vol up nad vol down buttons and then hold the power button.
The graphic should disappear, let go of power when screen goes black and then it should go into "download mode"
it took me over 2 hours the other night to get into download mode.
Well I got it into Download mode and on Odin it's saying File analysis and do not turn off target... so I guess that means it's working?
Well I think I just bricked it for good now. I had it in download mode, it started to reset everything and the screen turned green for a little while, I thought something was wrong when that happened so I just took the battery out again to turn it off... now it won't even turn back on.

[Q] G2x stuck in "S/W Upgrade" screen after NVflasher One Click

My phone is currently sitting with a "S/W upgrade" screen after a series of stupid events. I flashed recovery using ROM Manager before I had read that it fake flashed. I rebooted into recovery and installed CM7 nightly. Rebooted and it's stuck in a boot loop. So I finally see all the warnings against that so I figure I need to get a real recovery so I use the awesome guide from TGA_Gunnman. I follow all the instructions and it appears from the log on my PC that the CM recovery flashed successfully. I pull the cord, reinsert my battery and my phone just sits in the S/W upgrade screen. It's been like that for 30 minutes now.
What do I do?
I thought I'd done something wrong with my G2x because that happened to me too. Remove your battery and USB. Then insert your battery again. When you turn it on, make sure to hold both the power button and the volume down button until you see text that says android. If you, like me, thought you just had to hold the volume down and tap the power button (like my Nexus One), that might be your issue.
Sent from my Nexus One using Tapatalk
just disconnect usb, and go to recovery Power+vol down...
.....and congrats !
yep, I thought I bricked it too.. When you were done at the green screen where it said press any button, thats where you press whatever you want and then unplug the cord. Then, put the battery back in and hold down vol then power, don't let go until "android" pops up.. You did it man, just missing your last step..
Moved to proper forum
I can get to the Recovery screen, but I cant select any of the options....volume lets me scroll, but cant find anything to select any of the options....kinda new at this
power button to 'action' your selection... at least it works for me.
usajlh said:
My phone is currently sitting with a "S/W upgrade" screen after a series of stupid events. I flashed recovery using ROM Manager before I had read that it fake flashed. I rebooted into recovery and installed CM7 nightly. Rebooted and it's stuck in a boot loop. So I finally see all the warnings against that so I figure I need to get a real recovery so I use the awesome guide from TGA_Gunnman. I follow all the instructions and it appears from the log on my PC that the CM recovery flashed successfully. I pull the cord, reinsert my battery and my phone just sits in the S/W upgrade screen. It's been like that for 30 minutes now.
What do I do?
Click to expand...
Click to collapse
The "S/W upgrade" stays on, that's normal. See if your terminal window has completed whatever stuff it is doing. If you get a completed message, you are good to go and can safely pull out the USB chord even if your phone still says "S/W upgrade". Put back your battery and hold Power+Vol DOWN button and see if you get into cmw recovery.
so im trying to fix my friends phone and this is weird..
im able to go to cwm, wipe it all and flash a new rom.. it flashess successfully but when i reboot it goes back to the s/w update screen..it happens with any rom i flash.. its been sitting there for a while.. how long should i wait?
Once you flash the ROM you shouldn't be getting that screen...Does your friend has the G2x or 2x and which ROM did you flash?
Sounds like you screwed up the boot image. Go into APX mode again and reflash the recovery package making sure it completes, you hit a key to close the terminal window, and you hold the volume buttons the entire time. Then go into recovery and factory reset and clear the Dalvik cache. Then if you still get the S/W update screen you are going to need to go to the thread about fixing bricked phones and use the KDZ method to reflash the entire GB OTA package. There is also a new method to reinstall the entire OTA package using NVFlash but you have to hold the volume buttons down for about ten to fifteen minutes while everything flashes.

[Q] cwm help

I had an issue with my phone and basically had to start over. I took the FP1 upgrade. Now I have tried several times to odin the correct recovery so I can get back to where I was before the issue. Nothing is working. I keep getting the stock android recovery system. Help Please!
danstar said:
I had an issue with my phone and basically had to start over. I took the FP1 upgrade. Now I have tried several times to odin the correct recovery so I can get back to where I was before the issue. Nothing is working. I keep getting the stock android recovery system. Help Please!
Click to expand...
Click to collapse
You need to reflash cwm with Odin the stock recovery overwrites cwm when your on the stock ROM
Sent from my Galaxy Nexus using xda premium
I was on the stock rom and reflashed cwm using odin and it reverted back to the stock recovery each time. I had to odin the new rom I was going to first, then odin the new recovery and everything was fine.
danstar said:
I was on the stock rom and reflashed cwm using odin and it reverted back to the stock recovery each time. I had to odin the new rom I was going to first, then odin the new recovery and everything was fine.
Click to expand...
Click to collapse
After you Odin CWM, you need to immediately boot into CWM and flash a non-stock kernel. Stock kernels will overwrite CWM with stock recovery if they boot into the OS.
When you Odin cwm make shire autorestart is not checked. Odin cwm unplug phone take battery out. Put battery back in boot directly to cwm by pressing home, Vol up and power. Hold until Samsung logo comes up the second time then let go. Now you're in the flashes cwm go install superuser, then reboot . Install "root explorer" , sum privileges should b allowed , go to "system" folder find "recovery.sh" file, it has a yellow star. Click on the "Mount R/W" Press and hold on the recovery file till menu pops up, go to "permissions" uncheck all the boxes save and exit. Shut down phone, go to download mode with Odin flash cwm again make shire autorestart is not checked , unplug take bat out. Put bat back startup. You should be able to go to cwm any time now.
This is from one of the posts I read and memorized. Thanks go to whoever figured it out.
Sent from my SCH-I510 using XDA
been through this but cannot get the phone into download mode now? any ideas
headed over to imnuts
Morrisme said:
been through this but cannot get the phone into download mode now? any ideas
headed over to imnuts
Click to expand...
Click to collapse
Power the phone down completely. Pull the battery. Hold volume down while you plug in the USB cable. When it comes up in download mode, put battery back in.
This instruction, step 5.
What I do to get my download screen is : bat out , vol down, power then plug in cable (count) 1 and release power but hold vol down until download mode pops up. Then put battery in. That's the only way it works for me. Some ppl hold both buttons until download mode pops up, that don't work for me. Others can get it by pressing buttons n piping in battery and then connecting cable. Try some of these. I figured out my just by chance my finger slipped cause most can do it by pressing both buttons holding and plugging in. If I do it that way my phone either reboots or nothing happens.
Sent from my SCH-I510 using xda app-developers app
Don't use the power button at all to get into download mode. Just remove the battery, hold down volume down, and plug the USB cable in. It'll automatically power on. Then you should put the battery back in to help ensure a better chance at a clean flash.

Phone boots to recovery then fails and keeps trying

Im new to the rooting scene but did my research. I did a clean install of the MOAR rom and i have been rooted and had been using teamwin recovery and it has worked fine. The moar rom is new but was working all day today till now. I used the reboot into recovery feature from the power menu and now its stuck. IT tries to boot to recovery and i see the teamwin splash page and then it fails and just flashes the splash page. I take out the battery after a couple minutes and hope to boot normally but it tries and boot to recovery straight off. I dont know what to do at this point im just hoping theres a way to fix
Fixed it. I did a little more searching and someone had a similar problem and soeone offered how to boot straight into downlaod mode which is.
1. Take the battery out of the phone and unplug it from USB power.
2. Plug in USB power.
3. While holding down the volume-down button and the Home button, insert the battery
You have to install the tar file via Odin

Weird Bootloop (not actually a bootloop)

Phone: J4+ (SM-J415F)
I wanted flash the stock ROM via Odin on pc and something went wrong (i don't know what) and now the phone shows "An error has occured while updating the device software. Use the emergency function in the Smart Switch PC software." I tried to go in the download mode but the phone "restarts" every 2 seconds when i connect it to the pc or the charger.The recovery didn't work either.
Note: The phone doesn't start even if it is not connected to the PC or to a charger.
I'm also stuck in this weird .non. bootloop
Hey, I had this problem before. The Battery maybe depleted during flashing. You have to find a way to charge it.
Try to boot into Odin warning screen or the IMEI screen, it's where the device won't reboot while your connected to a charger, then give it some time to charge until you have enough time to flash your stock ROM.
Its what I did xd, just watch out for overheating. Using a GN variant.
I solved it by holding all 3 buttons and plugging into USB, it did the whole rebooting thing as usual but I kept the buttons held for about 15/20 reboots and then it FINALLY went into download and I could flash stock rom. If important or not, I'd left it charging all night but showed no sign of life whilst it 'charged'
Something to Try!
The issue seems to be with the HOME CSC is corrupted on the latest version - Probably something by Samsung to outdo the Combo files being produced.
PLUG-IN THE PHONE to PC (NOT WALL), Press and hold POWER + VOL UP + VOL DOWN to BOOT the phone to the ODIN message screen (with the warning), not the Download Screen itself > in this Screen release all the buttons at the same time, if you do this right you should still be on that same screen. Then simply press the POWER once. This should show a Barcode IMEI Serial, etc (Then leave for 5-15 mins on USB Charge then quickly swap with a wall charger).
Then leave it to charge for normally phone charging time. Later PUT INTO ODIN MODE and retry.
I have done this 3 times on this device to make sure this is the correct way.
You might get away booting it to ODIN and trying to swap the power but unsure about that.
After this Go to GOOGLE Search on your laptop/pc > search for SAMFIRM > Put in the model and Download the Combination for J415FXXU5ASK1 and then in SAMFIRM software click Download ROM > Tick the Binary Nature box and then Flash the Combination file in the AP button of ODIN then the on that ROM go to Orange Calculator (IME) type in *#0808# on the next screen select the option with ADB and RM & DMT (normally the bottom) then select PDA on the next and then SAVE and RESET then flash the SAMSUNG ROM with the CSC, not the HOME!<< Just a NOTE! Not Responsible for bricked devices if you do this wrong! Advice only! :good:

Categories

Resources