So I had a completely stock Galaxy s 4g, on gingerbread. I had the bright idea of rooting to try out different builds. I was in the middle of flashing when I noticed that what I was flashing was for the Vibrant. Well, it was either let it flash with that or stop the flash, so I stopped it. After searching for hours, I couldn't find a working link for a download to flash a custom build. I was able to find a "stock" flash, but for some reason I don't think it's right. I have problems with low call volume now and have to power the phone off and on to fix it temporarily. Everything else works fine, so far. Another thing I noticed is everyone shows firmware of 2.3.6, mine says 2.3.4????? Here's my info: sigh-t959v, baseband T959VUVKG4, kernel 2.6.35.7-t959vuvkg4-cl385158, build gingerbread.vuvkg4.
Any thoughts on what I should do?
Thanks in advance
This thread has heimdall one clicks that will get you back to stock kj6. Remember to flash once then after booting until you hear the t-mo jingle pull battery and put it back in download mode and check the flash bootloaders and flash it again.
http://forum.xda-developers.com/showthread.php?t=1358498
If you want root in the second post is a one click created by me. You can flash it instead of the plain stock one by bhundeven. But you need to flash the bootloaders to make sure you get rid of all the vibrant stuff.
Ok, thanks a lot. I will flash your build tomorrow when I get home from work. I'll let you know how it goes. Thanks again.
So I flashed your build and everythingis working great, even seems to be running faster. However, the wifi says "error" when I try and activate it. Is that a rom problem? Should I start over and try again?
It is because the kernel uses a different module then what is in the rom itself. That is why it is suppose to be used as a stepping stone to flash to a different rom.
Gotcha.
Related
used to be able to flash any combo...even I-9000 roms(darky's...) with proper kernel and modem combos.
Had no problems ever!
Now, ANY combination kills my signal. Paragon; perception, pheonix, the list goes on and on.
The only ROM i can run is Cognition. If i flash to a different kernel/modem combo,(even while running cognition) I have problems.
Now atleast I am stuck with a good ROM, but I would love to fine-tune with a different kernel/radio and I have NO idea why my phone is acting this way. I am thinking maybe it's a SIM card thing(I pulled the SIM out one timebefore the phone was fully shut down...
other than that I cannot think of anything weird I have done.
In between flashes I have ODIN'd back to H2 and then Master Cleared.
Flash via CWM. Root with 1-click.
PLEASE give me some idea of what I have done?!?!!?
Or is it warranty time for the phone due to 'GPS' issues..
Thanks
boardsportsrule said:
used to be able to flash any combo...even I-9000 roms(darky's...) with proper kernel and modem combos.
Had no problems ever!
Now, ANY combination kills my signal. Paragon; perception, pheonix, the list goes on and on.
The only ROM i can run is Cognition. If i flash to a different kernel/modem combo,(even while running cognition) I have problems.
Now atleast I am stuck with a good ROM, but I would love to fine-tune with a different kernel/radio and I have NO idea why my phone is acting this way. I am thinking maybe it's a SIM card thing(I pulled the SIM out one timebefore the phone was fully shut down...
other than that I cannot think of anything weird I have done.
In between flashes I have ODIN'd back to H2 and then Master Cleared.
Flash via CWM. Root with 1-click.
PLEASE give me some idea of what I have done?!?!!?
Or is it warranty time for the phone due to 'GPS' issues..
Thanks
Click to expand...
Click to collapse
Find the modem cognition uses that gives you the least problems. Are you flashing to stock before each ROM?
Sent from my SAMSUNG-SGH-I897 using XDA App
Yep, back to stock & master cleared between(only once problems arised..back in the day I could just flash to what I wanted and never really had a problem. Went back to stock once when the new flash responded strangely.)
Looking at cognition, I get minimal information, I THINK it's stock radio/kernel..
http://forum.xda-developers.com/showthread.php?t=912657
Any one???
I would..check your usb plug/cable/port first..make sure it isn't bad and effecting your data transfer..Make sure your not plugged into a external port and plug into PC directly..
Re down load your roms and kernels again..keep them separate from what you have already used..
Flash back to stock..master clear delete all data on your internal and your data
Re-install everything over again..cause it sounds like something got corrupted along the way
Mac
Mac11700 said:
it sounds like something got corrupted along the way
Click to expand...
Click to collapse
Thats how I am leaning, but i dont think it's with the roms/kernels/radios i have downloaded...since I have tried so many damn copies that wouldn't make sense. also tried downloading directly to phone, eliminating the "3rd party" computer, and have used drop box in the past...
I have flashed to stock and master cleared, i could do it again, but i am tempted to go back to stock and try to exchange it for a new one due to either random shut-offs or GPS(both of which mine are effected by..) but i would like to avoid this hassle...
If something did get corrupted, any idea how I'd solve that? I am at a loss as to what could have gotten corrupted that a odin'd stock + master clear wouldn't solve...?
boardsportsrule said:
If something did get corrupted, any idea how I'd solve that? I am at a loss as to what could have gotten corrupted that a odin'd stock + master clear wouldn't solve...?
Click to expand...
Click to collapse
It's possible that your phone has a hardware issue making it more finicky. Try stock for a bit and see if the problems go away. Maybe try Andromeda 1.0 and see how the KP1 modem works (or just flash KP1 on some other ROM).
opcow said:
It's possible that your phone has a hardware issue making it more finicky. Try stock for a bit and see if the problems go away. Maybe try Andromeda 1.0 and see how the KP1 modem works (or just flash KP1 on some other ROM).
Click to expand...
Click to collapse
hopped back to Stock... Gonna run things here, see which problems arise, and go from there. Can you flash a different kernel onto the stock ROM? I'd assume you need a 2.1 kernel, and i don't think many are retrofitted to 2.1, but the KP1 modem is a good idea, ill let things pan out on stock and see what happens if/when i flash kp1 modem.
funny fact: fire fly made problems for me... it's based on rogers 2.2, same as cognition. that seemed odd to me.
Background. Was using 2.2 for the longest time, loved Firefly. Went ahead and bit the bullet and decided to go to 2.3 and use Gingerbread. Solid week of great success. However I started notcing my antenna saying no signal. Several Reboots and still nothing worked. Decided I would One-Click Back to 2.1 and start fresh. Well I never had issues with Odin 1 Click before, but now I get in a boot loop (ATT SPlash Screen) I have noticed when its unloading the package after , the last thing i see is CSC and that it boots into the loop. Would love to get my phone back to stock so i can see if its a hardware or software issue with my antenna. I have looked at this link, http://forum.xda-developers.com/showpost.php?p=10056254&postcount=36 but was afraid I possibly might still have GB bootloaders on my phone. I would think not if Odin finished, but I just want to double check with the community so I dont brick.
Thanks guys.
Can you get into DL mode? IF so, i would try and Odin again. ALthough I looked at the link in your OP, unless your heart is set on 2.1JH7, i would use the Odin3 one click downloader. That will restore your phone to 2.1JF6 as well as flash the correct bootloaders. I have gone back and forth from continuum to cm7 a few times now using that method.
Thanks for the quick reply. however this is the 3rd time trying Odin-1 Click tonight and I still end up in a boot loop. I have redownloaded the file just to make sure I didnt have a corrupt one. I just want a stock system and see if the constant antenna issues continue. (Trust me Ive tried different modems and all those possibilities.) Is it safe with that link? I noticed when i do Odin they flash a sbin and bootloader. I am assuming that puts it back on 2.1
which Odin are you using? Are you using the one click program that gives you stock firmware... JF6 firmware?
It is here:
http://www.megaupload.com/?d=SBSMALFJ
Yup thats what I have. It looks like it doesn't load the android system. Soon as it says installing Multi-CSC its done and rebooting. It would seem like its not unpacking the files. I have no status bar at the bottom. I have no idea why its doing this. Here is the crazy part. If i go back to the ginberbread stock, its not a problem to get to boot.
while I'm no expert.. seems like a bootloader thing. Try downloading it again from the link i put up and see if it was maybe a corrupted download.
The bootloaders are the first thing flashed in odin. It stopped after that then you have stock bootloaders. Also if all you see is the white AT&T screen and then it reboots, that indicates stock bootloaders as well. The gb bootloaders have a black galaxy s I9000 screen as the param.lfs image.
I would bet money you have stock bootloaders, use that link you posted that work be perfect. If you go back to gingerbread and want to return to stock bootloaders you'll have to use one click again even though you got a problem from it this time, if you get the same problem you know this worked to fix it.
And lastly usually problems with cell signal are modem related ... Which one were you using, did you even try another one? That would've been my first move instead of going all the way back to stock.
Hey studacris,
I have been using Mosaic (Love the work you guys do over there). I did try and use the other method to get back to Stock Last night and it did the same thing. Just a bootloop. If its plugged into the USB cable it goes directly to the Battery Symbol, if its not the Att 3G bars loop. I can flash to Gingerbread stock and then apply Other Roms. I tried GR-2 and Mosaic again, but still nothing with the signals. I just dont like the fact I cant get back to Stock with those 2 different methods. What I think is odd is when I load Gingerbread, it seems like items are being unpacked and loaded. When i try to go to Stock, everything happens super quick, making me believe nothing ever gets installed on the Internal Card during the unpacking sequence. I am no pro, but thats just something i noticed. Here was my original post on the Mosaic board. http://forum.xda-developers.com/showthread.php?p=14043766&highlight=Rizz67#post14043766
ok so i rooted a few weeks ago and downloaded the usual apps. super user titanium back up and clock work mod. tried to flash a rom with clock work mod and got the e:signature verification failure message. found a post for a kernal that made clock work mod actually work so i tried to flash a rom. zSimplyAOKPV5_Dark to be exact. now it sticks on boot screen. i have searched for hours and cannot find a way to fix my problem. its my first rooted android and first attempted rom flash and i botched it right off the rip. please help?
Depending on what you did beforehand, you have some options.
If you have backed everything up previously, just flash back to stock with one of the one-click stock roms in the Development section (they're in a sticky).
If you haven't backed everything up, try holding V+/V-/power until it reboots. If it doesn't take you to recovery, you can try to flash a kernel (most likely one that would match the version of android/rom you were running prior to this flash) and see if it lets you into recovery. You'll have to flash it with either Odin or Heimdall, after rebooting into download mode (power off, hold V+/V-, insert USB).
If that doesn't work, though, the stock flashing would probably be your best and/or only bet.
it wont allow me into recovery though i can get to download mode by pulling the battery and pressing just the volume +- and plugging in the usb. i was trying to flash an ics slim rom. thanks for your very speedy response.
i have now tried to flash a stock rom however it is not working from there even with the stock kernal. now it is hanging on the at&t screen.
ok i got it. seems the kernal i flashed to help cwd work properly was the culprit. now i dont know how im going to flash this ics rom im looking at without it.
phoenixfriend said:
it wont allow me into recovery though i can get to download mode by pulling the battery and pressing just the volume +- and plugging in the usb. i was trying to flash an ics slim rom. thanks for your very speedy response.
i have now tried to flash a stock rom however it is not working from there even with the stock kernal. now it is hanging on the at&t screen.
ok i got it. seems the kernal i flashed to help cwd work properly was the culprit. now i dont know how im going to flash this ics rom im looking at without it.
Click to expand...
Click to collapse
Flash corn kernel if you have stock gingerbread
Sent from my SGH-I897
The utility in my signature can help you flash the Corn Kernel so that you will have CWM.
I have corn kernal and odin 3 on the computer at home. Ill do that tonight. Any suggestions on a good stable rom for a noob? Preferably ics. I hated posting for fear of being flamed as a noob. My wife keeps making fun of me for it so I kinda have to get it done. I want to fix hers also. Its a great little phone it just seem a bit buggy to me. Very laggy. Thanks for all the help.
Sent from my SAMSUNG-SGH-I897 using XDA
Maybe start with a KK4 based rom such as Legend and then move up to ICS after that. I only say that because there is a bug in ICS that could render your internal SD unusable. It's rare, but when it happens you will not be happy.
Still unable to get corn kernal to flash. I've tried a few of your guys fixes but I'm gonna have to get some other updates to my computer first.
Sent from my SAMSUNG-SGH-I897 using XDA
So I decided to start with fresh ICS install coming from leak 1. I didn't care if I ever was able to flash back to 2.3 so I used the FXZ files found in this thread http://forum.xda-developers.com/showthread.php?t=1961310
It started the flash and seemed to be working properly. Seemed to flash the MBM. Then erase the firmware and as It was writing the new It said flash failure. 18/1 or 1/18. After letting it sit for awhile and looking up some stuff I tried again and it keeps getting stuck at flashing MBM. So now what? I thought about trying the 2.3.6 FXZ but if it updated the MBM the first time that's probably not an option..What about just flashing the firmware? Anyway I'm hoping someone can help me out.
Edit:
Well I'm not sure what happened but I have managed to boot into Android. It was a fresh install and had me setup my phone again. When I enter fast boot I haven't seen the phone show up, as I wanted to try and flash again.
I don't know if I have a partial/buggy install or if it's perfectly fine. So far it seems to run alright, it did seem a little buggy when I was first setting it up though. I took some screen shots of the about phone area. Maybe someone can tell me if all the numbers are the same as what's in the FXZ.
http://forum.xda-developers.com/attachment.php?attachmentid=1804995&stc=1&d=1363284886
The kernel is the ICS one. I guess you're good. :thumbup:
Hello all,
Okay, I admit that I am gonna get a lot of "use the search tool first" replies, but please hear me out. I have done my fair share of searching. Its not that I haven't found anything, its just the things I found are useless for this SGS 4G. I really wanted to install Cyanogen Mo on the SGS (its not actually mine, a friend asked me to do it since he saw my old SGS GT-I9000 running CM).
I am gonna try and give a detailed report . The phone was originally from T-Mobile and now unlocked permanently. Its running firmware version 2.3.3 that I installed just recently. I found out that I can't install CWM on the stock kernel or bootloader or whatever and I needed a new of the thing. So I went on searching and searching....found a handful of help but none work. Every method breaks at some point and I go to the "firmware update failed" thing on the phone, which I then install 2.3.3 again using ODIN and try another method. I have tried a lot of things. Hemidall, ODIN, SuperOneClick, and a lot of gibbrish-sounding methods. None work. I am now running 2.3.3. Here are some infos:
ABOUT PHONE:
Model Number: SGH-T959V
Firmware Version: 2.3.3
Baseband Version: T959VUVKF1
Kernel Version: 2.6.35.7-T959VUVKF1-CL270364
Build Number: GINGERBREAD.VUVKF1
The files I used to flash to 2.3.3 using ODIN v1.85:
PIT: Hawk_Sidekick_VibrantPlus_831.pit
PDA: CODE_T959VUVKF1_CL270364_REV00_user_low_noship.tar.md5
PHONE: T959VUVKF1-Phone-CL1020302.tar.md5
CSC: SGH-T959V-CSC-TMB-VIBRANTP.tar.md5
I hope the above infos are enough. So, can anyone help me and point me to the right direction on how to install CWM and then install CM10 or 9 on my friends SGS 4G?
Thanks,
Tamrat
Hmmm, an interesting set of binaries, ones that don't ring a bell with me. I'm used to seeing T959VUVKJ6.
Where did you find those? Half curiosity, half trying to understand the problem, half since much of the "old" images for the phones got lost when Multiupload and what have you were shut down.
For the SGS4G, the kernel, root file system, and recovery file system are all in "boot.img" -- flash one, you flash them all. They can be flashed through Odin (assuming you really like Windows), heimdall (multi-platform), through recovery, or from a root command line (for the adventurous only).
I would say the most robust way to get where you need to be would be to use Lumin's guide to make sure you've got a viable Gingerbread set-up going, then flash something reliable to get you to MTD, like TeamAcid's CM9.
From there, you should know that some of the KK ROMs use slightly different MTD partitioning and aren't a "just flash this ROM and keep your data" kind of thing.
jeffsf said:
Hmmm, an interesting set of binaries, ones that don't ring a bell with me. I'm used to seeing T959VUVKJ6.
Where did you find those? Half curiosity, half trying to understand the problem, half since much of the "old" images for the phones got lost when Multiupload and what have you were shut down.
Click to expand...
Click to collapse
A long day Googling... and then a site turned up. One thing I forgot to mention was, before I installed this firmware, I had to use the "remove battery->plug usb->press the button combos->insert the battery" to enter download mode, but now I juts have to press vol down and power button.
Thanks for the reply,
Failure again
UPDATE:::
I tried to update to 2.3.6 as the guide suggests and I also wanted a clean stock OS in case the old one was not. But once again updating to 2.3.6 has been a pain. Kies Mini recognizes the phone but it doesn't recognize the firmware running on the phone. And also, firmware update is impossible since the button is greyed out.
I googled again and found the official 2.3.6 firmware for the phone (file name: T959VUVKJ6-REV00-home-low-CL694130.tar.md5) and tried flashing it using ODIN; absolutely no luck. It fails at the stage which says Slb.bin. Restarting the phone after that gives a "firmware upgrade failure" display. Only way to wake up the phone is to flash the previous OS back.
I am really confused here.
*********************EDIT***************
Some how, after like 10 retires and fiddling with ODIN, it finally flashed 2.3.6 to the SGS 4G. Still, fingers crossed.
*********************EDIT 2***************
Finally, its all working fine now. Thank you @jeffsf, thank you very much.
F*****************K
forgot an important step and now my IEMI number is gone........
do i throw the phone now, or is there any other way???
Don't throw your phone away! How do you know that you have "no IMEI" on your phone? We'll go from there.
Hopefully, you've backed up your data before starting to play around with ROMS. If so just load your backed up efs folder onto your storage & use Root Explorer to drop it over your existing one , it will overwrite your imei file & you will be good as new.
========================================================================================
I'm also in need of help, I have been running SlimSaber since last weekend, was wanting to try out Beanstalk. First full wipe, install & reboot wipe again, reinstall etc as per Dao's OP, but after the first install, it won't boot past the kernel splash. Tried again with same result. Decided to click it back to stock & start over, using Gremlin Remover (odin). Then saw that others were having similar issue so I tried to load in build from April1st.
But now it only boots back into recovery, won't boot to the OS ( everything indicated install was complete & no errors.)
1 clicked back again & just tried to put SlimSaber back on again, but have the same problem, will only boot into recovery.
I had to first load CM9 to get CWM 6.xx so I could install kk using TWRP
What am I not doing correctly? Thanks for any suggestions.
Flash kernel
Reboot recovery
Wipe all partitions
(Reboot recovery for good measure and wipe again if paranoid)
Install
Boot
If that doesn't do it, it is likely ROM or hardware.
---
Posted from whatever phone booted today
Since this is running GB VUVKG4, could you recommend a kernel that would work & get me to TWRP (or CWM 5.xx+)?
Either the Team Acid CM9 or Hefe Kernel should work.
---
Posted from whatever phone booted today